ISDN-MIB
79 objects
The MIB module to describe the management of ISDN interfaces.
Imported Objects
| IANAifType-MIB | IANAifType |
| IF-MIB | ifIndex InterfaceIndex |
| RFC1213-MIB | transmission |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP -- NOTIFICATION-GROUP |
| SNMPv2-SMI | Counter32 Gauge32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | DisplayString RowStatus TestAndIncr TEXTUAL-CONVENTION TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.10.20 | IdentityisdnMib | The MIB module to describe the management of ISDN interfaces. | ||
| 1.3.6.1.2.1.10.20.1 | NodeisdnMibObjects | |||
| 1.3.6.1.2.1.10.20.1.1 | NodeisdnBasicRateGroup | |||
| 1.3.6.1.2.1.10.20.1.1.1 | TableisdnBasicRateTable | not-accessible | current | Table containing configuration and operational parameters for all physical Basic Rate interfaces on this managed device. |
| 1.3.6.1.2.1.10.20.1.1.1.1 | RowisdnBasicRateEntry | not-accessible | current | An entry in the ISDN Basic Rate Table. |
| 1.3.6.1.2.1.10.20.1.1.1.1.1 | ColumnisdnBasicRateIfType | read-write | current | The physical interface type. For 'S/T' interfaces, also called 'Four-wire Basic Access Interface', the value of this object is isdns(75). For 'U' interfaces, a… |
| 1.3.6.1.2.1.10.20.1.1.1.1.2 | ColumnisdnBasicRateLineTopology | read-write | current | The line topology to be used for this interface. Note that setting isdnBasicRateIfType to isdns(75) does not necessarily mean a line topology of point-to-multi… |
| 1.3.6.1.2.1.10.20.1.1.1.1.3 | ColumnisdnBasicRateIfMode | read-write | current | The physical interface mode. For TE mode, the value of this object is te(1). For NT mode, the value of this object is nt(2). |
| 1.3.6.1.2.1.10.20.1.1.1.1.4 | ColumnisdnBasicRateSignalMode | read-write | current | The signaling channel operational mode for this interface. If active(1) there is a signaling channel on this interface. If inactive(2) a signaling channel is n… |
| 1.3.6.1.2.1.10.20.1.2 | NodeisdnBearerGroup | |||
| 1.3.6.1.2.1.10.20.1.2.1 | TableisdnBearerTable | not-accessible | current | This table defines port specific operational, statistics and active call data for ISDN B channels. Each entry in this table describes one B (bearer) channel. |
| 1.3.6.1.2.1.10.20.1.2.1.1 | RowisdnBearerEntry | not-accessible | current | Operational and statistics information relating to one port. A port is a single B channel. |
| 1.3.6.1.2.1.10.20.1.2.1.1.1 | ColumnisdnBearerChannelType | read-write | current | The B channel type. If the B channel is connected to a dialup line, this object has a value of dialup(1). In this case, it is controlled by an associated signa… |
| 1.3.6.1.2.1.10.20.1.2.1.1.2 | ColumnisdnBearerOperStatus | read-only | current | The current call control state for this port. idle(1): The B channel is idle. No call or call attempt is going on. connecting(2): A connection attempt (outgoin… |
| 1.3.6.1.2.1.10.20.1.2.1.1.3 | ColumnisdnBearerChannelNumber | read-only | current | The identifier being used by a signaling protocol to identify this B channel, also referred to as B channel number. If the Agent also supports the DS0 MIB, the… |
| 1.3.6.1.2.1.10.20.1.2.1.1.4 | ColumnisdnBearerPeerAddress | read-only | current | The ISDN address the current or last call is or was connected to. In some cases, the format of this information can not be predicted, since it largely depends … |
| 1.3.6.1.2.1.10.20.1.2.1.1.5 | ColumnisdnBearerPeerSubAddress | read-only | current | The ISDN subaddress the current or last call is or was connected to. The subaddress is an user supplied string of up to 20 IA5 characters and is transmitted tr… |
| 1.3.6.1.2.1.10.20.1.2.1.1.6 | ColumnisdnBearerCallOrigin | read-only | current | The call origin for the current or last call. If since system startup there was no call on this interface, this object has a value of unknown(1). |
| 1.3.6.1.2.1.10.20.1.2.1.1.7 | ColumnisdnBearerInfoType | read-only | current | The Information Transfer Capability for the current or last call. speech(2) refers to a non-data connection, whereas audio31(6) and audio7(7) refer to data mod… |
| 1.3.6.1.2.1.10.20.1.2.1.1.8 | ColumnisdnBearerMultirate | read-only | current | This flag indicates if the current or last call used multirate. The actual information transfer rate, in detail specified in octet 4.1 (rate multiplier), is th… |
| 1.3.6.1.2.1.10.20.1.2.1.1.9 | ColumnisdnBearerCallSetupTime | read-only | current | The value of sysUpTime when the ISDN setup message for the current or last call was sent or received. If since system startup there has been no call on this in… |
| 1.3.6.1.2.1.10.20.1.2.1.1.10 | ColumnisdnBearerCallConnectTime | read-only | current | The value of sysUpTime when the ISDN connect message for the current or last call was sent or received. If since system startup there has been no call on this … |
| 1.3.6.1.2.1.10.20.1.2.1.1.11 | ColumnisdnBearerChargedUnits | read-only | current | The number of charged units for the current or last connection. For incoming calls or if charging information is not supplied by the switch, the value of this … |
| 1.3.6.1.2.1.10.20.1.3 | NodeisdnSignalingGroup | |||
| 1.3.6.1.2.1.10.20.1.3.1 | ScalarisdnSignalingGetIndex | read-write | current | The recommended procedure for selecting a new index for isdnSignalingTable row creation is to GET the value of this object, and then to SET the object with the… |
| 1.3.6.1.2.1.10.20.1.3.2 | TableisdnSignalingTable | not-accessible | current | ISDN signaling table containing configuration and operational parameters for all ISDN signaling channels on this managed device. |
| 1.3.6.1.2.1.10.20.1.3.2.1 | RowisdnSignalingEntry | not-accessible | current | An entry in the ISDN Signaling Table. To create a new entry, only isdnSignalingProtocol needs to be specified before isdnSignalingStatus can become active(1). |
| 1.3.6.1.2.1.10.20.1.3.2.1.1 | ColumnisdnSignalingIndex | not-accessible | current | The index value which uniquely identifies an entry in the isdnSignalingTable. |
| 1.3.6.1.2.1.10.20.1.3.2.1.2 | ColumnisdnSignalingIfIndex | read-only | current | The ifIndex value of the interface associated with this signaling channel. |
| 1.3.6.1.2.1.10.20.1.3.2.1.3 | ColumnisdnSignalingProtocol | read-create | current | The particular protocol type supported by the switch providing access to the ISDN network to which this signaling channel is connected. |
| 1.3.6.1.2.1.10.20.1.3.2.1.4 | ColumnisdnSignalingCallingAddress | read-create | current | The ISDN Address to be assigned to this signaling channel. More specifically, this is the 'Calling Address information element' as being passed to the switch i… |
| 1.3.6.1.2.1.10.20.1.3.2.1.5 | ColumnisdnSignalingSubAddress | read-create | current | Supplementary information to the ISDN address assigned to this signaling channel. Usually, this is the subaddress as defined in Q.931. If there is no such numb… |
| 1.3.6.1.2.1.10.20.1.3.2.1.6 | ColumnisdnSignalingBchannelCount | read-create | current | The total number of B channels (bearer channels) managed by this signaling channel. The default value of this object depends on the physical interface type and… |
| 1.3.6.1.2.1.10.20.1.3.2.1.7 | ColumnisdnSignalingInfoTrapEnable | read-create | current | Indicates whether isdnMibCallInformation traps should be generated for calls on this signaling channel. |
| 1.3.6.1.2.1.10.20.1.3.2.1.8 | ColumnisdnSignalingStatus | read-create | current | This object is used to create and delete rows in the isdnSignalingTable. |
| 1.3.6.1.2.1.10.20.1.3.3 | TableisdnSignalingStatsTable | not-accessible | current | ISDN signaling table containing statistics information for all ISDN signaling channels on this managed device. Only statistical information which is not alread… |
| 1.3.6.1.2.1.10.20.1.3.3.1 | RowisdnSignalingStatsEntry | not-accessible | current | An entry in the ISDN Signaling statistics Table. |
| 1.3.6.1.2.1.10.20.1.3.3.1.1 | ColumnisdnSigStatsInCalls | read-only | current | The number of incoming calls on this interface. |
| 1.3.6.1.2.1.10.20.1.3.3.1.2 | ColumnisdnSigStatsInConnected | read-only | current | The number of incoming calls on this interface which were actually connected. |
| 1.3.6.1.2.1.10.20.1.3.3.1.3 | ColumnisdnSigStatsOutCalls | read-only | current | The number of outgoing calls on this interface. |
| 1.3.6.1.2.1.10.20.1.3.3.1.4 | ColumnisdnSigStatsOutConnected | read-only | current | The number of outgoing calls on this interface which were actually connected. |
| 1.3.6.1.2.1.10.20.1.3.3.1.5 | ColumnisdnSigStatsChargedUnits | read-only | current | The number of charging units on this interface since system startup. Only the charging units applying to the local interface, i.e. for originated calls or for … |
| 1.3.6.1.2.1.10.20.1.3.4 | TableisdnLapdTable | not-accessible | current | Table containing configuration and statistics information for all LAPD (D channel Data Link) interfaces on this managed device. Only statistical information wh… |
| 1.3.6.1.2.1.10.20.1.3.4.1 | RowisdnLapdEntry | not-accessible | current | An entry in the LAPD Table. |
| 1.3.6.1.2.1.10.20.1.3.4.1.1 | ColumnisdnLapdPrimaryChannel | read-write | current | If set to true(1), this D channel is the designated primary D channel if D channel backup is active. There must be exactly one primary D channel configured. If… |
| 1.3.6.1.2.1.10.20.1.3.4.1.2 | ColumnisdnLapdOperStatus | read-only | current | The operational status of this interface: inactive all layers are inactive l1Active layer 1 is activated, layer 2 datalink not established l2Active layer 1 is … |
| 1.3.6.1.2.1.10.20.1.3.4.1.3 | ColumnisdnLapdPeerSabme | read-only | current | The number of peer SABME frames received on this interface. This is the number of peer-initiated new connections on this interface. |
| 1.3.6.1.2.1.10.20.1.3.4.1.4 | ColumnisdnLapdRecvdFrmr | read-only | current | The number of LAPD FRMR response frames received. This is the number of framing errors on this interface. |
| 1.3.6.1.2.1.10.20.1.4 | NodeisdnEndpointGroup | |||
| 1.3.6.1.2.1.10.20.1.4.1 | ScalarisdnEndpointGetIndex | read-write | current | The recommended procedure for selecting a new index for isdnEndpointTable row creation is to GET the value of this object, and then to SET the object with the … |
| 1.3.6.1.2.1.10.20.1.4.2 | TableisdnEndpointTable | not-accessible | current | Table containing configuration for Terminal Endpoints. |
| 1.3.6.1.2.1.10.20.1.4.2.1 | RowisdnEndpointEntry | not-accessible | current | An entry in the Terminal Endpoint Table. The value of isdnEndpointIfType must be supplied for a row in this table to become active. |
| 1.3.6.1.2.1.10.20.1.4.2.1.1 | ColumnisdnEndpointIndex | not-accessible | current | The index value which uniquely identifies an entry in the isdnEndpointTable. |
| 1.3.6.1.2.1.10.20.1.4.2.1.2 | ColumnisdnEndpointIfIndex | read-only | current | The ifIndex value of the interface associated with this Terminal Endpoint. |
| 1.3.6.1.2.1.10.20.1.4.2.1.3 | ColumnisdnEndpointIfType | read-create | current | The interface type for this Terminal Endpoint. Interface types of x25ple(40) and isdn(63) are allowed. The interface type is identical to the value of ifType i… |
| 1.3.6.1.2.1.10.20.1.4.2.1.4 | ColumnisdnEndpointTeiType | read-create | current | The type of TEI (Terminal Endpoint Identifier) used for this Terminal Endpoint. In case of dynamic(1), the TEI value is selected by the switch. In case of stat… |
| 1.3.6.1.2.1.10.20.1.4.2.1.5 | ColumnisdnEndpointTeiValue | read-create | current | The TEI (Terminal Endpoint Identifier) value for this Terminal Endpoint. If isdnEndpointTeiType is set to static(2), valid numbers are 0..63, while otherwise t… |
| 1.3.6.1.2.1.10.20.1.4.2.1.6 | ColumnisdnEndpointSpid | read-create | current | The Service profile IDentifier (SPID) information for this Terminal Endpoint. The SPID is composed of 9-20 numeric characters. This information has to be defin… |
| 1.3.6.1.2.1.10.20.1.4.2.1.7 | ColumnisdnEndpointStatus | read-create | current | This object is used to create and delete rows in the isdnEndpointTable. |
| 1.3.6.1.2.1.10.20.1.5 | NodeisdnDirectoryGroup | |||
| 1.3.6.1.2.1.10.20.1.5.1 | TableisdnDirectoryTable | not-accessible | current | Table containing Directory Numbers. |
| 1.3.6.1.2.1.10.20.1.5.1.1 | RowisdnDirectoryEntry | not-accessible | current | An entry in the Directory Number Table. All objects in an entry must be set for a new row to become active. |
| 1.3.6.1.2.1.10.20.1.5.1.1.1 | ColumnisdnDirectoryIndex | not-accessible | current | The index value which uniquely identifies an entry in the isdnDirectoryTable. |
| 1.3.6.1.2.1.10.20.1.5.1.1.2 | ColumnisdnDirectoryNumber | read-create | current | A Directory Number. Directory Numbers are used to identify incoming calls on the signaling channel given in isdnDirectorySigIndex. The format of this informati… |
| 1.3.6.1.2.1.10.20.1.5.1.1.3 | ColumnisdnDirectorySigIndex | read-create | current | An index pointing to an ISDN signaling channel. Incoming calls are accepted on this signaling channel if the isdnDirectoryNumber is presented as Called Number … |
| 1.3.6.1.2.1.10.20.1.5.1.1.4 | ColumnisdnDirectoryStatus | read-create | current | This object is used to create and delete rows in the isdnDirectoryTable. |
| 1.3.6.1.2.1.10.20.2 | NodeisdnMibTrapPrefix | |||
| 1.3.6.1.2.1.10.20.2.0 | NodeisdnMibTraps | |||
| 1.3.6.1.2.1.10.20.2.0.1 | NotificationisdnMibCallInformation | current | This trap/inform is sent to the manager under the following condidions: - on incoming calls for each call which is rejected for policy reasons (e.g. unknown ne… | |
| 1.3.6.1.2.1.10.20.3 | NodeisdnMibConformance | |||
| 1.3.6.1.2.1.10.20.3.1 | NodeisdnMibCompliances | |||
| 1.3.6.1.2.1.10.20.3.1.1 | ComplianceisdnMibCompliance | read-only | current | The compliance statement for entities which implement the ISDN MIB. |
| 1.3.6.1.2.1.10.20.3.2 | NodeisdnMibGroups | |||
| 1.3.6.1.2.1.10.20.3.2.1 | GroupisdnMibBasicRateGroup | current | A collection of objects required for ISDN Basic Rate physical interface configuration and statistics. | |
| 1.3.6.1.2.1.10.20.3.2.2 | GroupisdnMibBearerGroup | current | A collection of objects required for ISDN Bearer channel control and statistics. | |
| 1.3.6.1.2.1.10.20.3.2.3 | GroupisdnMibSignalingGroup | current | A collection of objects required for ISDN D channel configuration and statistics. | |
| 1.3.6.1.2.1.10.20.3.2.4 | GroupisdnMibEndpointGroup | current | A collection of objects describing Terminal Endpoints. | |
| 1.3.6.1.2.1.10.20.3.2.5 | GroupisdnMibDirectoryGroup | current | A collection of objects describing directory numbers. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| IsdnSignalingProtocol | INTEGER { other(1), dss1(2), etsi(3), dass2(4), ess4(5), ess5(6), dms100(7), dms250(8), ni1(9), ni2(10), ni3(11), vn2(12), vn3(13), vn4(14), vn6(15), kdd(16), ins64(17), ins1500(18), itr6(19), cornet(20), ts013(21), ts014(22), qsig(23), swissnet2(24), swissnet3(25) } | current | This data type is used as the syntax of the isdnSignalingProtocol object in the definition of ISDN-MIB's isdnSignalingTable. The definition of this textual convention with the addition of newly assigned values is publis… |