Juniper-ATM-1483-Profile-MIB
51 objects
The ATM Profile MIB for the Juniper Networks, Inc. enterprise.
Imported Objects
| Juniper-MIBs | juniMibs |
| Juniper-PROFILE-MIB | JuniProfileIfEncaps |
| Juniper-TC | JuniEnable JuniSetMap |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Gauge32 Integer32 MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.4874.2.2.58 | IdentityjuniAtm1483ProfileMIB | The ATM Profile MIB for the Juniper Networks, Inc. enterprise. | ||
| 1.3.6.1.4.1.4874.2.2.58.1 | NodejuniAtm1483ProfileObjects | |||
| 1.3.6.1.4.1.4874.2.2.58.1.1 | NodejuniAtm1483Profile | |||
| 1.3.6.1.4.1.4874.2.2.58.1.1.1 | TablejuniAtm1483ProfileTable | not-accessible | current | This table contains profiles for configuring bulk ATM circuits. Entries in this table are created/deleted as a side-effect of corresponding operations to the j… |
| 1.3.6.1.4.1.4874.2.2.58.1.1.1.1 | RowjuniAtm1483ProfileEntry | not-accessible | current | A profile describing VCC configuration of an ATM subinterface. |
| 1.3.6.1.4.1.4874.2.2.58.1.1.1.1.1 | ColumnjuniAtm1483ProfileId | not-accessible | current | The integer identifier associated with this profile. A value for this identifier is determined by locating or creating a profile name in the juniProfileNameTab… |
| 1.3.6.1.4.1.4874.2.2.58.1.1.1.1.2 | ColumnjuniAtm1483ProfileSetMap | read-write | current | A bitmap representing which objects in this entry have been explicitly configured. See the definition of the JuniSetMap TEXTUAL-CONVENTION for details of use. … |
| 1.3.6.1.4.1.4874.2.2.58.1.1.1.1.3 | ColumnjuniAtm1483ProfileVccType | read-write | current | Specifies the encapsulation used by the circuit to carry IP datagrams. Encapsulations are as specified in RFC1483 Multiprotocol Interconnect over ATM. 'autocon… |
| 1.3.6.1.4.1.4874.2.2.58.1.1.1.1.4 | ColumnjuniAtm1483ProfileVccServiceCategory | read-write | current | Service category for this circuit: ubr Unspecified Bit Rate (best effort). ubrPcr Unspecified Bit Rate with Peak Cell Rate limit. nrtVbr Non-realtime Variable … |
| 1.3.6.1.4.1.4874.2.2.58.1.1.1.1.5 | ColumnjuniAtm1483ProfileVccPcr | read-write | current | Peak Cell Rate, in kilo-bits per second (kbps), of this circuit. This parameter is only required when juniAtm1483ProfileVccServiceCategory is configured to hav… |
| 1.3.6.1.4.1.4874.2.2.58.1.1.1.1.6 | ColumnjuniAtm1483ProfileVccScr | read-write | current | Sustained Cell Rate, in kilo-bits per second (kbps), of this circuit. This parameter is only required when juniAtm1483ProfileVccServiceCategory is configured t… |
| 1.3.6.1.4.1.4874.2.2.58.1.1.1.1.7 | ColumnjuniAtm1483ProfileVccMbs | read-write | current | Maximum Burst Size, in cells, of this circuit. This parameter is only required when juniAtm1483ProfileVccServiceCategory is configured to have one of the follo… |
| 1.3.6.1.4.1.4874.2.2.58.1.1.1.1.8 | ColumnjuniAtm1483ProfileIfAlias | read-write | current | This object is an 'alias' name for the interface as specified by a network manager, and provides a non-volatile 'handle' for the interface. This object initial… |
| 1.3.6.1.4.1.4874.2.2.58.1.1.1.1.9 | ColumnjuniAtm1483ProfileAdvisoryRxSpeed | read-write | current | Advisory receive speed, in kilobits per second (kbps), of this subinterface. This object has no impact on forwarding performance but may be used as a hint for … |
| 1.3.6.1.4.1.4874.2.2.58.1.1.1.1.10 | ColumnjuniAtm1483ProfileVccOamAdminStatus | read-write | current | The administrative state of OAM for the interface identified by this entry. |
| 1.3.6.1.4.1.4874.2.2.58.1.1.1.1.11 | ColumnjuniAtm1483ProfileVccOamLoopbackFrequency | read-write | current | The OAM loopback frequency for the interface identified by this entry. |
| 1.3.6.1.4.1.4874.2.2.58.1.1.1.1.12 | ColumnjuniAtm1483ProfileVcClassName | read-write | current | The name of the ATM VC class assigned to this profile. |
| 1.3.6.1.4.1.4874.2.2.58.1.1.2 | TablejuniAtm1483ProfileAutoConfTable | not-accessible | current | Configures recognition of incoming data encapsulation types that trigger autoconfiguration on an interface. |
| 1.3.6.1.4.1.4874.2.2.58.1.1.2.1 | RowjuniAtm1483ProfileAutoConfEntry | not-accessible | current | Configures recognition of an incoming data encapsulation type that triggers autoconfiguration on an interface. |
| 1.3.6.1.4.1.4874.2.2.58.1.1.2.1.1 | ColumnjuniAtm1483ProfileAutoConfId | not-accessible | current | The integer identifier associated with this profile. A value for this identifier is determined by locating or creating a profile name in the juniProfileNameTab… |
| 1.3.6.1.4.1.4874.2.2.58.1.1.2.1.2 | ColumnjuniAtm1483ProfileAutoConfEncaps | not-accessible | current | The encapsulating protocol type to which the autconfiguration information in this entry applies. The valid values are: ip(0), ppp(1), pppoe(17), bridgedEtherne… |
| 1.3.6.1.4.1.4874.2.2.58.1.1.2.1.3 | ColumnjuniAtm1483ProfileAutoConfEnable | read-write | current | When enabled, permits autoconfiguration of the specified interface when the specified encapsulation is recognized in an incoming data frame. This parameter can… |
| 1.3.6.1.4.1.4874.2.2.58.1.1.2.1.4 | ColumnjuniAtm1483ProfileAutoConfLockoutMin | read-write | current | The lower bound, in seconds, of the time range used to specify the duration of the lockout of the encapsulation type from recognition for the specified interfa… |
| 1.3.6.1.4.1.4874.2.2.58.1.1.2.1.5 | ColumnjuniAtm1483ProfileAutoConfLockoutMax | read-write | current | The upper bound, in seconds, of the time range used to specify the duration of the lockout of the encapsulation type from recognition for the specified interfa… |
| 1.3.6.1.4.1.4874.2.2.58.1.1.3 | TablejuniAtm1483ProfileNestedProfileTable | not-accessible | current | Specifies nested profiles for incoming data encapsulation types. Entries in this table are created/deleted as a side-effect of corresponding operations to the … |
| 1.3.6.1.4.1.4874.2.2.58.1.1.3.1 | RowjuniAtm1483ProfileNestedProfileEntry | not-accessible | current | Specifies nested profile for incoming data encapsulation type. |
| 1.3.6.1.4.1.4874.2.2.58.1.1.3.1.1 | ColumnjuniAtm1483ProfileNestedProfileId | not-accessible | current | The integer identifier associated with this profile. A value for this identifier is determined by locating or creating a profile name in the juniProfileNameTab… |
| 1.3.6.1.4.1.4874.2.2.58.1.1.3.1.2 | ColumnjuniAtm1483ProfileNestedProfileEncaps | not-accessible | current | The encapsulating protocol type to which the nested profile specified in this entry applies. The valid values are: ip(0), ppp(1), pppoe(17), bridgedEthernet(19) |
| 1.3.6.1.4.1.4874.2.2.58.1.1.3.1.3 | ColumnjuniAtm1483ProfileNestedProfileUpperIfProfileName | read-write | current | The name of profile used for the protocol type specified by juniAtm1483ProfileNestedProfileEncaps. |
| 1.3.6.1.4.1.4874.2.2.58.1.1.4 | TablejuniAtm1483ProfileSubscriberTable | not-accessible | current | Configures subscriber identity used in circumstances where the remote subscriber's identity cannot be queried directly (e.g. dynamic IPoA operation). Entries i… |
| 1.3.6.1.4.1.4874.2.2.58.1.1.4.1 | RowjuniAtm1483ProfileSubscriberEntry | not-accessible | current | Configures subscriber identity used in circumstances where the remote subscriber's identity cannot be queried directly (e.g. dynamic IPoA operation). |
| 1.3.6.1.4.1.4874.2.2.58.1.1.4.1.1 | ColumnjuniAtm1483ProfileSubscriberId | not-accessible | current | The integer identifier associated with this profile. A value for this identifier is determined by locating or creating a profile name in the juniProfileNameTab… |
| 1.3.6.1.4.1.4874.2.2.58.1.1.4.1.2 | ColumnjuniAtm1483ProfileSubscriberEncaps | not-accessible | current | The encapsulating protocol type to which the subscriber information in this entry applies. The valid values are: ip(0), bridgedEthernet(19) |
| 1.3.6.1.4.1.4874.2.2.58.1.1.4.1.3 | ColumnjuniAtm1483ProfileSubscriberNamePrefix | read-write | current | If enabled, indicates whether the value of juniSubscriberName is a prefix rather than a full name. This parameter is valid only when juniAtm1483ProfileSubscrib… |
| 1.3.6.1.4.1.4874.2.2.58.1.1.4.1.4 | ColumnjuniAtm1483ProfileSubscriberName | read-write | current | If juniAtm1483ProfileSubscriberNamePrefix has the value 'enabled', the value of this object serves as the prefix of a full subscriber name. The full name is co… |
| 1.3.6.1.4.1.4874.2.2.58.1.1.4.1.5 | ColumnjuniAtm1483ProfileSubscriberPasswordPrefix | read-write | current | If enabled, indicates whether the value of juniAtm1483ProfileSubscriberPassword is a prefix rather than a full password. This parameter is valid only when juni… |
| 1.3.6.1.4.1.4874.2.2.58.1.1.4.1.6 | ColumnjuniAtm1483ProfileSubscriberPassword | read-write | current | The subscriber's password. If juniAtm1483ProfileSubscriberPasswordPrefix has the value 'enabled', the value of this object serves as the prefix of a full subsc… |
| 1.3.6.1.4.1.4874.2.2.58.1.1.4.1.7 | ColumnjuniAtm1483ProfileSubscriberDomain | read-write | current | The subscriber's domain. This parameter is valid only when juniAtm1483ProfileSubscriberEncaps is configured to one of the following values: ip(0), bridgedEther… |
| 1.3.6.1.4.1.4874.2.2.58.4 | NodejuniAtm1483ProfileConformance | |||
| 1.3.6.1.4.1.4874.2.2.58.4.1 | NodejuniAtm1483ProfileCompliances | |||
| 1.3.6.1.4.1.4874.2.2.58.4.1.1 | CompliancejuniAtm1483ProfileCompliance | obsolete | Obsolete compliance statement for entities which implement the Juniper ATM Profile MIB. This statement became obsolete when ifALias support was added to profil… | |
| 1.3.6.1.4.1.4874.2.2.58.4.1.2 | CompliancejuniAtm1483ProfileCompliance2 | obsolete | Obsolete compliance statement for entities which implement the Juniper ATM Profile MIB. This statement became obsolete when lockout objects were added to juniA… | |
| 1.3.6.1.4.1.4874.2.2.58.4.1.3 | CompliancejuniAtm1483ProfileCompliance3 | obsolete | Obsolete compliance statement for entities which implement the Juniper ATM Profile MIB. | |
| 1.3.6.1.4.1.4874.2.2.58.4.1.4 | CompliancejuniAtm1483ProfileCompliance4 | current | The compliance statement for entities which implement the Juniper ATM Profile MIB. | |
| 1.3.6.1.4.1.4874.2.2.58.4.2 | NodejuniAtm1483ProfileGroups | |||
| 1.3.6.1.4.1.4874.2.2.58.4.2.1 | GroupjuniAtm1483ProfileGroup | obsolete | Obsolete collection of objects providing management of profile functionality for ATM subinterfaces in a Juniper product. This group became obsolete when ifALia… | |
| 1.3.6.1.4.1.4874.2.2.58.4.2.2 | GroupjuniAtm1483ProfileGroup2 | obsolete | Obolete collection of objects providing management of profile functionalityfor ATM subinterfaces in a Juniper product. This group became obsolete when OAM supp… | |
| 1.3.6.1.4.1.4874.2.2.58.4.2.3 | GroupjuniAtm1483ProfileGroup3 | obsolete | Obsolete collection of objects providing management of profile functionality for ATM subinterfaces in a Juniper product. This group became obsolete when ifALia… | |
| 1.3.6.1.4.1.4874.2.2.58.4.2.4 | GroupjuniAtm1483ProfileGroup4 | obsolete | Obsolete collection of objects providing management of profile functionality for ATM subinterfaces in a Juniper product. This group became obsolete when Encaps… | |
| 1.3.6.1.4.1.4874.2.2.58.4.2.5 | GroupjuniAtm1483ProfileGroup5 | obsolete | Obsolete collection of objects providing management of profile functionality for ATM subinterfaces in a Juniper product. | |
| 1.3.6.1.4.1.4874.2.2.58.4.2.6 | GroupjuniAtm1483ProfileGroup6 | current | A collection of objects providing management of profile functionality for ATM subinterfaces in a Juniper product. |