Juniper-DS1-MIB
51 objects
The DS1/E1 MIB for the Juniper enterprise. This MIB contains managed objects to supplement those found in RFC1406 DS1/E1 MIB.
Imported Objects
| IF-MIB | ifIndex InterfaceIndexOrZero |
| Juniper-MIBs | juniMibs |
| Juniper-TC | JuniNextIfIndex JuniTimeSlotMap |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | DisplayString RowStatus |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.4874.2.2.5 | IdentityjuniDs1MIB | The DS1/E1 MIB for the Juniper enterprise. This MIB contains managed objects to supplement those found in RFC1406 DS1/E1 MIB. | ||
| 1.3.6.1.4.1.4874.2.2.5.1 | NodejuniDs1Objects | |||
| 1.3.6.1.4.1.4874.2.2.5.1.1 | TablejuniDsx1ConfigTable | not-accessible | current | This table contains entries for DS1/E1 interfaces present in the system. |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1 | RowjuniDsx1ConfigEntry | not-accessible | current | Each entry describes the characteristics of an DS1/E1 interface. |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.1 | ColumnjuniDsx1TimeSlotMap | read-only | current | A bitmap representing the timeslots on the DS1/E1 interface that have been allocated for service. For channelized DS1/E1, set bits reflect the union of timeslo… |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.2 | ColumnjuniDsx1Ds1ChannelNumber | read-create | current | This variable represents the channel number of the DS1/E1 on its parent DS3/E3. A value of 0 indicates this DS1/E1 does not have a parent DS3/E3. |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.3 | ColumnjuniDsx1Capabilities | read-only | current | A value which indicates the set of capabilities of the DS1/E1 interface. The value is a sum. This sum initially takes the value zero. Then, for each capability… |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.4 | ColumnjuniDsx1Mode | read-create | current | This variable represents the DS1/E1 interface mode. The value of the juniDsx1Capabilities object for the DS1/E1 interface indicates the valid set of values for… |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.5 | ColumnjuniDsx1LineBuildOutCapabilities | read-only | current | A value which indicates the set of line build out capabilities of the DS1/E1 interface. The value is a sum. This sum initially takes the value zero. Then, for … |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.6 | ColumnjuniDsx1LineBuildOutType | read-create | current | This variable represents the configured line build out type of the DS1/E1 interface. The value of the juniDsx1LineBuildOutCapabilities object for the DS1/E1 in… |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.7 | ColumnjuniDsx1LineAttenuation | read-create | current | This variable represents the configured line attenuation of the DS1/E1 interface. Note that the value of this object only takes effect when the value of the ju… |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.8 | ColumnjuniDsx1LineLength | read-create | current | This variable represents the length of the DS1/E1 line in meters. Note that the value of this object only takes effect when the value of the juniDsx1LineBuildO… |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.9 | ColumnjuniDsx1LowerIfIndex | read-create | current | The ifIndex of the interface over which this Dsx1 interface is to be layered. A value of zero indicates no layering. An implementation may choose to require th… |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.10 | ColumnjuniDsx1RowStatus | read-create | current | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndG… |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.11 | ColumnjuniDsx1SendCode | read-create | current | This variable indicates what type of code is being sent across the DS1 interface by the device. |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.12 | ColumnjuniDsx1YellowAlarm | read-create | current | This bitmap indicates the yellow alarm settings, and is the sum of the capabilities. |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.13 | ColumnjuniDsx1RemoteLoopback | read-create | current | This variable indicates the remote loopback setting. |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.14 | ColumnjuniDsx1FdlCarrier | read-create | current | Specifies the interface is used in carrier environment. |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.15 | ColumnjuniDsx1FdlEic | read-create | current | This is the equipment identification code. |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.16 | ColumnjuniDsx1FdlLic | read-create | current | This is the location identification code. |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.17 | ColumnjuniDsx1FdlFic | read-create | current | This is the frame identification code. |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.18 | ColumnjuniDsx1FdlUnit | read-create | current | This is the unit identification code. |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.19 | ColumnjuniDsx1FdlPfi | read-create | current | This is the facility identification code. |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.20 | ColumnjuniDsx1FdlPort | read-create | current | This is the equipment port number. |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.21 | ColumnjuniDsx1FdlGenerator | read-create | current | This is the generator number. |
| 1.3.6.1.4.1.4874.2.2.5.1.1.1.22 | ColumnjuniDsx1FdlTransmit | read-create | current | Specifies transmission enabling. path - Bit 0 for path transmit. When this bit is set indicates path transmit is enabled; otherwise path transmit disabled. idl… |
| 1.3.6.1.4.1.4874.2.2.5.1.2 | ScalarjuniDs1NextIfIndex | read-only | current | Coordinate ifIndex value allocation for entries in juniDsx1ConfigTable. A GET of this object returns the next available ifIndex value to be used to create an e… |
| 1.3.6.1.4.1.4874.2.2.5.1.3 | TablejuniDsx1FarEndConfigTable | not-accessible | current | The DS1 Far End Configuration table. |
| 1.3.6.1.4.1.4874.2.2.5.1.3.1 | RowjuniDsx1FarEndConfigEntry | not-accessible | current | An entry in the DS1 Far End Configuration table. |
| 1.3.6.1.4.1.4874.2.2.5.1.3.1.1 | ColumnjuniDsx1FarEndLineIndex | not-accessible | current | The index value which uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is … |
| 1.3.6.1.4.1.4874.2.2.5.1.3.1.2 | ColumnjuniDsx1FarEndEquipCode | read-only | current | This is the Far End Equipment Identification code that describes the specific piece of equipment. It is sent within the Path Identification Message. |
| 1.3.6.1.4.1.4874.2.2.5.1.3.1.3 | ColumnjuniDsx1FarEndLocationIDCode | read-only | current | This is the Far End Location Identification code that describes the specific location of the equipment. It is sent within the Path Identification Message. |
| 1.3.6.1.4.1.4874.2.2.5.1.3.1.4 | ColumnjuniDsx1FarEndFrameIDCode | read-only | current | This is the Far End Frame Identification code that identifies where the equipment is located within a building at a given location. It is sent within the Path … |
| 1.3.6.1.4.1.4874.2.2.5.1.3.1.5 | ColumnjuniDsx1FarEndUnitCode | read-only | current | This is the Far End code that identifies the equipment location within a bay. It is sent within the Path Identification Message. |
| 1.3.6.1.4.1.4874.2.2.5.1.3.1.6 | ColumnjuniDsx1FarEndFacilityIDCode | read-only | current | This code identifies a specific Far End DS1 path. It is sent within the Path Identification Message. |
| 1.3.6.1.4.1.4874.2.2.5.1.3.1.7 | ColumnjuniDsx1FarEndPortNumber | read-only | current | This code identifies the port number of the Far End DS1. It is sent within the Idle Signal Message. |
| 1.3.6.1.4.1.4874.2.2.5.1.3.1.8 | ColumnjuniDsx1FarEndGeneratorNumber | read-only | current | This code identifies the Far End DS1 Generator Number. It is sent within the Test Signal Message. |
| 1.3.6.1.4.1.4874.2.2.5.1.3.1.9 | ColumnjuniDsx1FarEndCarrier | read-only | current | Specifies the interface is used in carrier environment. It is sent with all FDL messages. |
| 1.3.6.1.4.1.4874.2.2.5.4 | NodejuniDs1Conformance | |||
| 1.3.6.1.4.1.4874.2.2.5.4.1 | NodejuniDs1Compliances | |||
| 1.3.6.1.4.1.4874.2.2.5.4.1.1 | CompliancejuniDs1Compliance | obsolete | Obsolete compliance statement for entities which implement the Juniper DS1/E1 MIB. This statement became obsolete when new objects were added. | |
| 1.3.6.1.4.1.4874.2.2.5.4.1.2 | CompliancejuniDs1Compliance2 | obsolete | Obsolete compliance statement for entities which implement the Juniper DS1/E1 MIB. This statement became obsolete when dynamic DS1 interface support was added. | |
| 1.3.6.1.4.1.4874.2.2.5.4.1.3 | CompliancejuniDs1Compliance3 | obsolete | Obsolete compliance statement for entities which implement the Juniper DS1/E1 MIB. This statement became obsolete when FDL support was added. | |
| 1.3.6.1.4.1.4874.2.2.5.4.1.4 | CompliancejuniDs1Compliance4 | obsolete | Obsolete compliance statement for entities which implement the Juniper DS1/E1 MIB. This statement became obsolete when support for remote FDL strings and FDL t… | |
| 1.3.6.1.4.1.4874.2.2.5.4.1.5 | CompliancejuniDs1Compliance5 | current | The compliance statement for entities which implement the Juniper DS1/E1 MIB. | |
| 1.3.6.1.4.1.4874.2.2.5.4.2 | NodejuniDs1Groups | |||
| 1.3.6.1.4.1.4874.2.2.5.4.2.1 | GroupjuniDs1Group | obsolete | Obsolete collection of objects providing management of DS1/E1 interfaces in a Juniper product. This group became obsolete when new objects where added to the M… | |
| 1.3.6.1.4.1.4874.2.2.5.4.2.2 | GroupjuniDs1Group2 | obsolete | Obsolete collection of objects providing management of DS1/E1 interfaces in a Juniper product. This group became obsolete when dynamic DS1 interface support wa… | |
| 1.3.6.1.4.1.4874.2.2.5.4.2.3 | GroupjuniDs1Group3 | obsolete | Obsolete collection of objects providing management of DS1/E1 interfaces in a Juniper product. This group became obsolete when FDL support was added. | |
| 1.3.6.1.4.1.4874.2.2.5.4.2.4 | GroupjuniDs1Group4 | obsolete | Obsolete collection of objects providing management of DS1/E1 interfaces in a Juniper product. This group became obsolete when support for remote FDL strings a… | |
| 1.3.6.1.4.1.4874.2.2.5.4.2.5 | GroupjuniDs1Group5 | current | A collection of objects providing management of DS1/E1 interfaces in a Juniper product. |