LINKSYS-Physicaldescription-MIB
84 objects
The private MIB module definition for physical device configuration.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.89.53.4.1.3 | IdentityrlPhysicalDescription | The private MIB module definition for physical device configuration. | ||
| 1.3.6.1.4.1.89.53.4.1.3.5 | TablerlPhdModuleHotSwapTable | not-accessible | current | For each module (board) there is an entry describing its Hot Swap status |
| 1.3.6.1.4.1.89.53.4.1.3.5.1 | RowrlPhdModuleHotSwapEntry | not-accessible | current | A entry of this table specifies a module (board) Hot Swap status |
| 1.3.6.1.4.1.89.53.4.1.3.5.1.1 | ColumnrlPhdModuleHotSwapAdminStatus | read-write | current | The desired state of the module. The off(1) state indicates that the module is not used and its rlPhdModuleHotSwapOperStatus is always off(2). The on{1) state … |
| 1.3.6.1.4.1.89.53.4.1.3.5.1.2 | ColumnrlPhdModuleHotSwapOperStatus | read-only | current | The current Hot Swap state of the module. If rlPhdModuleHotSwapAdminStatus is down(2) then rlPhdModuleHotSwapOperStatus should be down(2). If rlPhdModuleHotSwa… |
| 1.3.6.1.4.1.89.53.4.1.3.6 | TablerlPhdStackOrderTable | not-accessible | current | This table enables the user to configure the order of the stack units as displayed on his GUI. The order of the entries in this table corresponds to the last c… |
| 1.3.6.1.4.1.89.53.4.1.3.6.1 | RowrlPhdStackOrderEntry | not-accessible | current | A entry of this table specifies a stack unit in the position desired by the user |
| 1.3.6.1.4.1.89.53.4.1.3.6.1.1 | ColumnrlPhdStackOrderCurrentUnitPosition | not-accessible | current | The current stack unit position. |
| 1.3.6.1.4.1.89.53.4.1.3.6.1.2 | ColumnrlPhdStackOrderDesiredUnitPosition | read-write | current | The desired stack unit position. Note that setting this MIB object will take effect only after setting the rlPhdStackReorder MIB object below. After setting th… |
| 1.3.6.1.4.1.89.53.4.1.3.6.1.3 | ColumnrlPhdStackOrderUnitIndex | not-accessible | current | This is the original unit index, i.e. has the same value as rlPhdStackUnit above. |
| 1.3.6.1.4.1.89.53.4.1.3.6.1.4 | ColumnrlPhdStackOrderUnitType | read-only | current | The type of the stack unit described by this entry. It has the same value as rlPhdStackType above. This information is duplicated here only for easier retrieva… |
| 1.3.6.1.4.1.89.53.4.1.3.7 | ScalarrlPhdStackReorder | read-write | current | Setting this MIB object will cause the settings of the rlPhdStackOrderDesiredUnitPosition MIB object instances to take effect. After setting this MIB object an… |
| 1.3.6.1.4.1.89.53.4.1.3.8 | ScalarrlPhdNumberOfUnits | read-only | current | Shows the current number of units in the stack. |
| 1.3.6.1.4.1.89.53.4.1.3.9 | ScalarrlPhdMaxNumberOfUnits | read-only | current | Shows the maximum number of units in the stack. |
| 1.3.6.1.4.1.89.53.4.1.3.10 | ScalarrlPhdForceMasterUnit | read-write | current | Force unit to be master. |
| 1.3.6.1.4.1.89.53.4.1.3.11 | ScalarrlPhdStackFixedUnit | read-write | current | Determine which unit will be on bottom/top of list on Show-List command(see . |
| 1.3.6.1.4.1.89.53.4.1.3.12 | ScalarrlPhdStackFixedUnitLocation | read-write | current | Determine the bottom/top object in the stack table. |
| 1.3.6.1.4.1.89.53.4.1.3.13 | ScalarrlPhdStackReloadUnit | read-write | current | Reset a specific unit. |
| 1.3.6.1.4.1.89.53.4.1.3.14 | TablerlPhdUnitGenParamTable | not-accessible | current | For each module (board) there is an entry describing it in this module |
| 1.3.6.1.4.1.89.53.4.1.3.14.1 | RowrlPhdUnitGenParamEntry | not-accessible | current | A entry of this table specifies a module (board) |
| 1.3.6.1.4.1.89.53.4.1.3.14.1.1 | ColumnrlPhdUnitGenParamStackUnit | read-only | current | The index of the stack unit to which this conceptual row corresponds. |
| 1.3.6.1.4.1.89.53.4.1.3.14.1.2 | ColumnrlPhdUnitGenParamSoftwareVersion | read-only | current | Serial number of the product. |
| 1.3.6.1.4.1.89.53.4.1.3.14.1.3 | ColumnrlPhdUnitGenParamFirmwareVersion | read-only | current | Serial number of the product. |
| 1.3.6.1.4.1.89.53.4.1.3.14.1.4 | ColumnrlPhdUnitGenParamHardwareVersion | read-only | current | Serial number of the product. |
| 1.3.6.1.4.1.89.53.4.1.3.14.1.5 | ColumnrlPhdUnitGenParamSerialNum | read-write | current | Serial number of the product. |
| 1.3.6.1.4.1.89.53.4.1.3.14.1.6 | ColumnrlPhdUnitGenParamAssetTag | read-write | current | Serial number of the product. |
| 1.3.6.1.4.1.89.53.4.1.3.14.1.7 | ColumnrlPhdUnitGenParamServiceTag | read-only | current | Asset tag of the product. |
| 1.3.6.1.4.1.89.53.4.1.3.14.1.8 | ColumnrlPhdUnitGenParamSoftwareDate | read-only | current | Date of product's software. |
| 1.3.6.1.4.1.89.53.4.1.3.14.1.9 | ColumnrlPhdUnitGenParamFirmwareDate | read-only | current | Date of product's firmware. |
| 1.3.6.1.4.1.89.53.4.1.3.14.1.10 | ColumnrlPhdUnitGenParamManufacturer | read-only | current | Product's Manufacturer. |
| 1.3.6.1.4.1.89.53.4.1.3.14.1.11 | ColumnrlPhdUnitGenParamModelName | read-only | current | Model Name. |
| 1.3.6.1.4.1.89.53.4.1.3.14.1.12 | ColumnrlPhdUnitGenParamMd5ChksumBoot | read-only | current | MD5 Checksum for Boot |
| 1.3.6.1.4.1.89.53.4.1.3.14.1.13 | ColumnrlPhdUnitGenParamMd5ChksumImage1 | read-only | current | MD5 Checksum for Image 1 |
| 1.3.6.1.4.1.89.53.4.1.3.14.1.14 | ColumnrlPhdUnitGenParamMd5ChksumImage2 | read-only | current | MD5 Checksum for Image 2 |
| 1.3.6.1.4.1.89.53.4.1.3.14.1.15 | ColumnrlPhdUnitGenParamRegistrationDone | read-write | current | Registration Done. |
| 1.3.6.1.4.1.89.53.4.1.3.14.1.16 | ColumnrlPhdUnitGenParamRegistrationSuppressed | read-write | current | Registration Suppressed. |
| 1.3.6.1.4.1.89.53.4.1.3.15 | TablerlPhdUnitEnvParamTable | not-accessible | current | For each module (board) there is an entry describing it in this module |
| 1.3.6.1.4.1.89.53.4.1.3.15.1 | RowrlPhdUnitEnvParamEntry | not-accessible | current | A entry of this table specifies a module (board) |
| 1.3.6.1.4.1.89.53.4.1.3.15.1.1 | ColumnrlPhdUnitEnvParamStackUnit | read-only | current | The index of the stack unit to which this conceptual row corresponds. Note that the index will be the same index as the index of a 'chassis' physical entity in… |
| 1.3.6.1.4.1.89.53.4.1.3.15.1.2 | ColumnrlPhdUnitEnvParamMainPSStatus | read-only | current | The mandatory state of the main PS being instrumented. |
| 1.3.6.1.4.1.89.53.4.1.3.15.1.3 | ColumnrlPhdUnitEnvParamRedundantPSStatus | read-only | current | The mandatory state of the redundant PS being instrumented. |
| 1.3.6.1.4.1.89.53.4.1.3.15.1.4 | ColumnrlPhdUnitEnvParamFan1Status | read-only | current | The mandatory state of the FAN 1 being instrumented. |
| 1.3.6.1.4.1.89.53.4.1.3.15.1.5 | ColumnrlPhdUnitEnvParamFan2Status | read-only | current | The mandatory state of the FAN 2 being instrumented. |
| 1.3.6.1.4.1.89.53.4.1.3.15.1.6 | ColumnrlPhdUnitEnvParamFan3Status | read-only | current | The mandatory state of the FAN 3 being instrumented. |
| 1.3.6.1.4.1.89.53.4.1.3.15.1.7 | ColumnrlPhdUnitEnvParamFan4Status | read-only | current | The mandatory state of the FAN 4 being instrumented. |
| 1.3.6.1.4.1.89.53.4.1.3.15.1.8 | ColumnrlPhdUnitEnvParamFan5Status | read-only | current | The mandatory state of the FAN 5 being instrumented. |
| 1.3.6.1.4.1.89.53.4.1.3.15.1.9 | ColumnrlPhdUnitEnvParamTempSensorValue | read-only | current | Current value for the Sensor being instrumented. |
| 1.3.6.1.4.1.89.53.4.1.3.15.1.10 | ColumnrlPhdUnitEnvParamTempSensorStatus | read-only | current | Status value for the Sensor being instrumented. |
| 1.3.6.1.4.1.89.53.4.1.3.15.1.11 | ColumnrlPhdUnitEnvParamUpTime | read-only | current | Up time of the unit in 100th of second (sec/100). |
| 1.3.6.1.4.1.89.53.4.1.3.15.1.12 | ColumnrlPhdUnitEnvParamMonitorAutoRecoveryEnable | read-write | current | Disable environment automatic recovery option |
| 1.3.6.1.4.1.89.53.4.1.3.15.1.13 | ColumnrlPhdUnitEnvParamMonitorTemperatureStatus | read-only | current | Display environment monitoring chassis temperature status |
| 1.3.6.1.4.1.89.53.4.1.3.15.1.14 | ColumnrlPhdUnitEnvParamMonitorOperStatus | read-only | current | Display environment automatic recovery current status (active/not active) |
| 1.3.6.1.4.1.89.53.4.1.3.16 | ScalarrlPhdStackOrderTopUnit | read-write | current | This scalar mib holds the Top unit for the stack order command |
| 1.3.6.1.4.1.89.53.4.1.3.17 | ScalarrlPhdStackOrderBottomUnit | read-write | current | This scalar mib holds the Bottom unit for the stack order command |
| 1.3.6.1.4.1.89.53.4.1.3.18 | ScalarrlPhdStackOrderPermutation | read-write | current | This scalar mib holds stack permutation |
| 1.3.6.1.4.1.89.53.4.1.3.19 | ScalarrlPhdNumberOfPoeUnits | read-only | current | Shows the current number of poe units in the stack. |
| 1.3.6.1.4.1.89.53.4.1.3.20 | TablerlPhdPoeTable | not-accessible | current | For each module (board) there is an entry describing it in this module |
| 1.3.6.1.4.1.89.53.4.1.3.20.1 | RowrlPhdPoeEntry | not-accessible | current | A entry of this table specifies a module (board) |
| 1.3.6.1.4.1.89.53.4.1.3.20.1.1 | ColumnrlPhdPoeStackUnit | read-only | current | The stack unit to which this module belongs. |
| 1.3.6.1.4.1.89.53.4.1.3.20.1.2 | ColumnrlPhdPoePresent | read-only | current | The present state of the PoE module. The no(1) state indicates that the PoE module is not present. The yes{2) state indicates that the PoE module is present. |
| 1.3.6.1.4.1.89.53.4.1.3.21 | ScalarrlPhdPhyLedStackUnit | read-write | current | This scalar mib holds the unit number for the stack light command |
| 1.3.6.1.4.1.89.53.4.1.3.22 | ScalarrlPhdPhyLedTimeout | read-write | current | This scalar mib holds the timeout for the stack light command. May be in the range 2..60 sec. (default - 5 sec.), if the timeout = 0 - all units return to norm… |
| 1.3.6.1.4.1.89.53.4.1.3.23 | TablerlCascadeTable | not-accessible | current | For each cascaded port for stacking unit there is an entry describing it in this table |
| 1.3.6.1.4.1.89.53.4.1.3.23.1 | RowrlCascadeEntry | not-accessible | current | An entry of this table specifies a cascaded link information in a unit |
| 1.3.6.1.4.1.89.53.4.1.3.23.1.1 | ColumnrlCascadeNeighborIfIndex | read-only | current | The ifIndex of a stacking port in the neighbor unit - 0 means not connected; other integer indicates the IfIndex. |
| 1.3.6.1.4.1.89.53.4.1.3.23.1.2 | ColumnrlCascadeNeighborUnit | read-only | current | The unit number of the neighbor unit - 0 means not connected; other integer indicates the unit number. |
| 1.3.6.1.4.1.89.53.4.1.3.23.1.3 | ColumnrlCascadeTrunkId | read-only | current | The id of the trunk, the stacking port is member, zero if the port is not member of trunk. |
| 1.3.6.1.4.1.89.53.4.1.3.23.1.4 | ColumnrlCascadeUnitId | read-only | current | The unit number matching the current ifIndex |
| 1.3.6.1.4.1.89.53.4.1.3.24 | TablerlCascadeAfterResetTable | not-accessible | current | For each cascaded port for stacking unit there is an entry describing it in this table after reset |
| 1.3.6.1.4.1.89.53.4.1.3.24.1 | RowrlCascadeAfterResetEntry | not-accessible | current | A entry of this table specifies a cascaded port information in a unit after reset |
| 1.3.6.1.4.1.89.53.4.1.3.24.1.1 | ColumnrlCascadeIfIndexAfterReset | read-only | current | The ifIndex of a stacking port after reset. |
| 1.3.6.1.4.1.89.53.4.1.3.24.1.2 | ColumnrlCascadeTrunkIdAfterReset | read-write | current | The Id of the trunk, the stacking port will be member after reset, zero if the port is not member of trunk. |
| 1.3.6.1.4.1.89.53.4.1.3.24.1.3 | ColumnrlCascadeRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.89.53.4.1.4 | ScalarrlPhdStackConnect2 | read-only | current | The unit number connected to the Hyper GLink right side connection - 0 means not connected; other integer indicates the unit number. |
| 1.3.6.1.4.1.89.53.4.1.5 | ScalarrlPhdStackSofrwareVer | read-only | current | The Software version of the unit. |
| 1.3.6.1.4.1.89.53.4.1.6 | ScalarrlPhdStackProductID | read-only | current | The Product ID of the unit. |
| 1.3.6.1.4.1.89.53.4.1.7 | ScalarrlPhdStackMacAddr | read-only | current | The physical (MAC) address of the unit. |
| 1.3.6.1.4.1.3955.1000.201.0.186 | NotificationrlStackUnitRemoved | current | Trap indicating that a unit was removed from the stack. | |
| 1.3.6.1.4.1.3955.1000.201.0.187 | NotificationrlStackConfigChangedRingChain | current | Trap indicating that the configuration of the stack has changed. - from ring to chain - from chain to ring. | |
| 1.3.6.1.4.1.3955.1000.201.0.188 | NotificationrlStackBackupUnitRemoved | current | Trap indicating that the backup unit was removed from the stack. | |
| 1.3.6.1.4.1.3955.1000.201.0.189 | NotificationrlStackMasterSwitchover | current | Trap indicating that a new master was elected. The old maste is the backup now. | |
| 1.3.6.1.4.1.3955.1000.201.0.190 | NotificationrlStackUnitDifferentSwVersion | current | Trap indicating that the new unit added to the stack has different software version than the master. | |
| 1.3.6.1.4.1.3955.1000.201.0.191 | NotificationrlStackDuplicateUnitNotJoin | current | Trap indicating that a new unit with duplicated unit id was added to the stack - but it will not join the stack. | |
| 1.3.6.1.4.1.3955.1000.201.0.195 | NotificationrlStackLinkChange | current | Trap indicating that Link has change in one of the Stacking Ports. |