MOXA-CN2600-MIB
352 objects
The MIB module for Moxa Terminal Server CN2600 series specific information.
Imported Objects
| SNMPv2-SMI | enterprises IpAddress OBJECT-TYPE |
| SNMPv2-TC | DateAndTime DisplayString MacAddress TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.8691 | Nodemoxa | |||
| 1.3.6.1.4.1.8691.2 | Nodenport | |||
| 1.3.6.1.4.1.8691.2.11 | Identitycn2600 | The MIB module for Moxa Terminal Server CN2600 series specific information. | ||
| 1.3.6.1.4.1.8691.2.11.1 | NodeswMgmt | |||
| 1.3.6.1.4.1.8691.2.11.1.1 | Nodeoverview | |||
| 1.3.6.1.4.1.8691.2.11.1.1.1 | ScalarmodelName | read-only | current | The model name of the CN2600. |
| 1.3.6.1.4.1.8691.2.11.1.1.2 | ScalarserialNumber | read-only | current | The serial number of the CN2600. Every Terminal Server CN2600 series is assigned a unique serial number before it is shipped. |
| 1.3.6.1.4.1.8691.2.11.1.1.3 | ScalarfirmwareVersion | read-only | current | The version of the firmware currently running on the CN2600. |
| 1.3.6.1.4.1.8691.2.11.1.1.4 | ScalarviewLan1IpAddress | read-only | current | The IP address of the CN2600's LAN1 interface. |
| 1.3.6.1.4.1.8691.2.11.1.1.5 | ScalarviewLan1MacAddress | read-only | current | The MAC address of the CN2600's LAN1 interface. |
| 1.3.6.1.4.1.8691.2.11.1.1.6 | ScalarviewLan1Speed | read-only | current | The current speed and link status of the CN2600's built-in LAN1 port. The possible values are 'No link', '10M/Link,' or '100M/Link.' |
| 1.3.6.1.4.1.8691.2.11.1.1.7 | ScalarviewLan2IpAddress | read-only | current | The IP address of the CN2600's LAN2 interface. |
| 1.3.6.1.4.1.8691.2.11.1.1.8 | ScalarviewLan2MacAddress | read-only | current | The MAC address of the CN2600's LAN2 interface. |
| 1.3.6.1.4.1.8691.2.11.1.1.9 | ScalarviewLan2Speed | read-only | current | The current speed and link status of the CN2600's built-in LAN2 port. The possible values are 'No link', '10M/Link,' or '100M/Link.' |
| 1.3.6.1.4.1.8691.2.11.1.1.10 | ScalarupTime | read-only | current | The time (in human-readable notation) since the system was was last re-initialized. |
| 1.3.6.1.4.1.8691.2.11.1.1.11 | Scalarpower1Status | read-only | current | The on/off status of power 1 |
| 1.3.6.1.4.1.8691.2.11.1.1.12 | Scalarpower2Status | read-only | current | The on/off status of power 2 for 2AC model |
| 1.3.6.1.4.1.8691.2.11.1.2 | NodebasicSetting | |||
| 1.3.6.1.4.1.8691.2.11.1.2.1 | NodeserverSetting | |||
| 1.3.6.1.4.1.8691.2.11.1.2.1.1 | ScalarserverName | read-write | current | A text string used to identify the CN2600. |
| 1.3.6.1.4.1.8691.2.11.1.2.1.2 | ScalarserverLocation | read-write | current | A text string used to identify the location of the CN2600. This option is useful for specifying the location or application of different CN2600. |
| 1.3.6.1.4.1.8691.2.11.1.2.2 | NodetimeSetting | |||
| 1.3.6.1.4.1.8691.2.11.1.2.2.1 | ScalartimeZone | read-write | current | The time-zone index of the CN2600. |
| 1.3.6.1.4.1.8691.2.11.1.2.2.2 | ScalarlocalTime | read-write | current | The system time in seconds since 1970/1/1. |
| 1.3.6.1.4.1.8691.2.11.1.2.2.3 | ScalartimeServer | read-write | current | The Terminal Server CN2600 series uses SNTP (RFC-1769) for auto time calibration. Input the correct 'Time server' IP address or domain name. Once the Terminal … |
| 1.3.6.1.4.1.8691.2.11.1.3 | NodenetworkSetting | |||
| 1.3.6.1.4.1.8691.2.11.1.3.1 | Scalarlan1IpConfiguration | read-write | current | The IP configuration mode of the CN2600. You can choose from four possible IP configuration modes: Static, DHCP, DHCP/BOOTP, BOOTP, and PPPoE. |
| 1.3.6.1.4.1.8691.2.11.1.3.2 | Scalarlan1IpAddress | read-write | current | An IP address is a number assigned to a network device (such as a computer) as a permanent address on the network. Computers use the IP address to identify and… |
| 1.3.6.1.4.1.8691.2.11.1.3.3 | Scalarlan1NetMask | read-write | current | A subnet mask represents all of the network hosts at one geographic location, in one building, or on the same local area network. When a packet is sent out ove… |
| 1.3.6.1.4.1.8691.2.11.1.3.4 | Scalarlan1DefaultGateway | read-only | current | A gateway is a network computer that acts as an entrance to another network. Usually, the computers that control traffic within the network or at the local Int… |
| 1.3.6.1.4.1.8691.2.11.1.3.5 | Scalarlan1Speed | read-write | current | IEEE802.3 Ethernet supports the auto negotiation speed function to get suitable speeds. However, for connecting to some switches/hubs, the communication speed … |
| 1.3.6.1.4.1.8691.2.11.1.3.6 | Scalarlan1PppoeUserAccount | read-write | current | The user account used by the CN2600 to access the Internet using PPPoE. For dynamic broad band networks such as xDSL or Cable Modem, users must enter the usern… |
| 1.3.6.1.4.1.8691.2.11.1.3.7 | Scalarlan1PppoePassword | read-write | current | The password used by the CN2600 to access the Internet using PPPoE. For dynamic broad band networks such as xDSL or Cable Modem, users must enter the username … |
| 1.3.6.1.4.1.8691.2.11.1.3.8 | Scalarlan2IpConfiguration | read-write | current | The IP configuration mode of the CN2600. You can choose from four possible IP configuration modes: Static, DHCP, DHCP/BOOTP, BOOTP, and PPPoE. |
| 1.3.6.1.4.1.8691.2.11.1.3.9 | Scalarlan2IpAddress | read-write | current | An IP address is a number assigned to a network device (such as a computer) as a permanent address on the network. Computers use the IP address to identify and… |
| 1.3.6.1.4.1.8691.2.11.1.3.10 | Scalarlan2NetMask | read-write | current | A subnet mask represents all of the network hosts at one geographic location, in one building, or on the same local area network. When a packet is sent out ove… |
| 1.3.6.1.4.1.8691.2.11.1.3.11 | Scalarlan2DefaultGateway | read-only | current | A gateway is a network computer that acts as an entrance to another network. Usually, the computers that control traffic within the network or at the local Int… |
| 1.3.6.1.4.1.8691.2.11.1.3.12 | Scalarlan2Speed | read-write | current | IEEE802.3 Ethernet supports the auto negotiation speed function to get suitable speeds. However, for connecting to some switches/hubs, the communication speed … |
| 1.3.6.1.4.1.8691.2.11.1.3.13 | Scalarlan2PppoeUserAccount | read-write | current | The user account used by the CN2600 to access the Internet using PPPoE. For dynamic broad band networks such as xDSL or Cable Modem, users must enter the usern… |
| 1.3.6.1.4.1.8691.2.11.1.3.14 | Scalarlan2PppoePassword | read-write | current | The password used by the CN2600 to access the Internet using PPPoE. For dynamic broad band networks such as xDSL or Cable Modem, users must enter the username … |
| 1.3.6.1.4.1.8691.2.11.1.3.15 | ScalardnsServer1IpAddr | read-write | current | The first DNS server address. When the user wants to visit a particular website, the computer asks a Domain Name System (DNS) server for the website��s cor… |
| 1.3.6.1.4.1.8691.2.11.1.3.16 | ScalardnsServer2IpAddr | read-write | current | The second DNS server address. When the user wants to visit a particular website, the computer asks a Domain Name System (DNS) server for the website��s co… |
| 1.3.6.1.4.1.8691.2.11.1.3.17 | ScalarwinsFunction | read-write | current | Enable or disable the WINS server. |
| 1.3.6.1.4.1.8691.2.11.1.3.18 | ScalarwinsServer | read-write | current | If a WINS Server is connected to the network, use this field to record the WINS Server��s IP address. TCP/IP uses IP addresses to identify hosts, but users… |
| 1.3.6.1.4.1.8691.2.11.1.3.19 | ScalarroutingProtocol | read-write | current | The routing protocol used by the CN2600. This value could be none, RIP-1, or RIP-2. |
| 1.3.6.1.4.1.8691.2.11.1.3.20 | ScalargratuitousArp | read-write | current | Enable or disable the gratuitous ARP function. For some applications, users need the Terminal Server CN2600 series to send broadcast packets to update the ARP … |
| 1.3.6.1.4.1.8691.2.11.1.3.21 | ScalargratuitousArpSendPeriod | read-write | current | The send period of the gratuitous ARP function. |
| 1.3.6.1.4.1.8691.2.11.1.4 | NodeportSetting | |||
| 1.3.6.1.4.1.8691.2.11.1.4.1 | NodeopModeSetting | |||
| 1.3.6.1.4.1.8691.2.11.1.4.1.1 | NodeopMode | |||
| 1.3.6.1.4.1.8691.2.11.1.4.1.1.1 | TableopModePortTable | not-accessible | current | The serial ports' operation mode table. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.1.1.1 | RowopModePortEntry | not-accessible | current | The serial port's operation mode entry. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.1.1.1.1 | ColumnportIndex | read-only | current | The serial port index. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.1.1.1.2 | ColumnportApplication | read-write | current | The application of the serial port. Note that changing this setting may also change the operation mode. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.1.1.1.3 | ColumnportMode | read-write | current | The operation mode of the serial port. Note that changing this setting may also change the application. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2 | Nodeapplication | |||
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.1 | NodedeviceControl | |||
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.1.1 | TabledeviceControlTable | not-accessible | current | The Device Control application table. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.1.1.1 | RowdeviceControlEntry | not-accessible | current | The Device Control application entry. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.1.1.1.1 | ColumndeviceControlTcpAliveCheck | read-write | current | The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The Terminal Server CN2600 series device serve… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.1.1.1.2 | ColumndeviceControlMaxConnection | read-write | current | Max connection is usually used when the user needs to receive data from different hosts simultaneously. The factory default is 1. In this case, only one specif… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.1.1.1.3 | ColumndeviceControlIgnoreJammedIp | read-write | current | Previously, when Max connection was set to a value greater than 1, and the serial device was transmitting data, if any one of the connected hosts stopped respo… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.1.1.1.4 | ColumndeviceControlAllowDriverControl | read-write | current | If Max connection is greater than 1, CN2600 will ignore driver control commands from all connected hosts. However, if you set Allow driver control to YES, cont… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.1.1.1.5 | ColumndeviceControlConnectionDownRTS | read-write | current | For some applications, serial devices must obtain the Ethernet link status by reading the RTS signal from the Terminal Server CN2600 series device server. If t… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.1.1.1.6 | ColumndeviceControlConnectionDownDTR | read-write | current | For some applications, serial devices must obtain the Ethernet link status by reading the DTR signal from the Terminal Server CN2600 series device server. If t… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2 | Nodesocket | |||
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1 | TablesocketTable | not-accessible | current | The Socket application table. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1 | RowsocketEntry | not-accessible | current | The Socket application entry. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.1 | ColumnsocketTcpAliveCheck | read-write | current | The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The Terminal Server CN2600 series device serve… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.2 | ColumnsocketInactivityTime | read-write | current | 0 ms: TCP connection is not closed when the serial line is idle. 1-65535 ms: The Terminal Server CN2600 series device server automatically closes the TCP conne… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.3 | ColumnsocketMaxConnection | read-write | current | Max connection is usually used when the user needs to receive data from different hosts simultaneously. The factory default is 1. In this case, only one specif… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.4 | ColumnsocketIgnoreJammedIp | read-write | current | Previously, when Max connection was set to a value greater than 1, and the serial device was transmitting data, if any one of the connected hosts stopped respo… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.5 | ColumnsocketAllowDriverControl | read-write | current | If Max connection is greater than 1, CN2600 will ignore driver control commands from all connected hosts. However, if you set Allow driver control to YES, cont… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.6 | ColumnsocketTcpPort | read-write | current | The 'TCP port' is the TCP port that the Terminal Server CN2600 series uses to listen to connections, and that other devices must use to contact the Terminal Se… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.7 | ColumnsocketCmdPort | read-write | current | The 'Command port' is a TCP port used to listen for IP-Serial Lib commands from the host. In order to prevent a TCP port conflict with other applications, the … |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.8 | ColumnsocketTcpServerConnectionDownRTS | read-write | current | For some applications, serial devices must obtain the Ethernet link status from the RTS signal sent by the Terminal Server CN2600 series device server. If this… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.9 | ColumnsocketTcpServerConnectionDownDTR | read-write | current | For some applications, serial devices must obtain the Ethernet link status from the DTR signal sent by the Terminal Server CN2600 series device server. If this… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.10 | ColumnsocketTcpClientDestinationAddress1 | read-write | current | The Terminal Server CN2600 series can connect actively to a remote host that has this IP address. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.11 | ColumnsocketTcpClientDestinationPort1 | read-write | current | The Terminal Server CN2600 series can connect actively to a remote host that has this TCP port number. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.12 | ColumnsocketTcpClientDestinationAddress2 | read-write | current | The Terminal Server CN2600 series can connect actively to a remote host that has this IP address. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.13 | ColumnsocketTcpClientDestinationPort2 | read-write | current | The Terminal Server CN2600 series can connect actively to a remote host that has this TCP port number. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.14 | ColumnsocketTcpClientDestinationAddress3 | read-write | current | The Terminal Server CN2600 series can connect actively to a remote host that has this IP address. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.15 | ColumnsocketTcpClientDestinationPort3 | read-write | current | The Terminal Server CN2600 series can connect actively to a remote host that has this port number. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.16 | ColumnsocketTcpClientDestinationAddress4 | read-write | current | The Terminal Server CN2600 series can connect actively to a remote host that has this IP address. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.17 | ColumnsocketTcpClientDestinationPort4 | read-write | current | The Terminal Server CN2600 series can connect actively to a remote host that has this port number. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.18 | ColumnsocketTcpClientDesignatedLocalPort1 | read-write | current | The local TCP port used to connect actively to the remote host. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.19 | ColumnsocketTcpClientDesignatedLocalPort2 | read-write | current | The local TCP port used to connect actively to the remote host. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.20 | ColumnsocketTcpClientDesignatedLocalPort3 | read-write | current | The local TCP port used to connect actively to the remote host. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.21 | ColumnsocketTcpClientDesignatedLocalPort4 | read-write | current | The local TCP port used to connect actively to the remote host. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.22 | ColumnsocketTcpClientConnectionControl | read-write | current | Events that cause the TCP client to drop the connection. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.23 | ColumnsocketUdpDestinationAddress1Begin | read-write | current | The Terminal Server CN2600 series can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and socketUdpDestina… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.24 | ColumnsocketUdpDestinationAddress1End | read-write | current | The Terminal Server CN2600 series can actively send UDP packets to remote hosts whose IP addresses are in the range between socketUdpDestinationAddress1Begin a… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.25 | ColumnsocketUdpDestinationPort1 | read-write | current | The Terminal Server CN2600 series can actively send UDP packets to remote hosts that have this port number. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.26 | ColumnsocketUdpDestinationAddress2Begin | read-write | current | The Terminal Server CN2600 series can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and socketUdpDestina… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.27 | ColumnsocketUdpDestinationAddress2End | read-write | current | The Terminal Server CN2600 series can actively send UDP packets to the remote hosts whose IP addresses are in the range between socketUdpDestinationAddress2Beg… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.28 | ColumnsocketUdpDestinationPort2 | read-write | current | The Terminal Server CN2600 series can actively send UDP packets to the remote hosts that have this TCP port number. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.29 | ColumnsocketUdpDestinationAddress3Begin | read-write | current | The Terminal Server CN2600 series can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and socketUdpDestina… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.30 | ColumnsocketUdpDestinationAddress3End | read-write | current | The Terminal Server CN2600 series can actively send UDP packets to remote hosts whose IP addresses are in the range between socketUdpDestinationAddress3Begin a… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.31 | ColumnsocketUdpDestinationPort3 | read-write | current | The Terminal Server CN2600 series can actively send UDP packets to remote hosts that have this TCP port number. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.32 | ColumnsocketUdpDestinationAddress4Begin | read-write | current | The Terminal Server CN2600 series can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and socketUdpDestina… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.33 | ColumnsocketUdpDestinationAddress4End | read-write | current | The Terminal Server CN2600 series can actively send UDP packets to remote hosts whose IP addresses are in the range between socketUdpDestinationAddress4Begin a… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.34 | ColumnsocketUdpDestinationPort4 | read-write | current | The Terminal Server CN2600 series can actively send UDP packets to remote hosts that have this TCP port number. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.2.1.1.35 | ColumnsocketUdpLocalListenPort | read-write | current | The UDP port that the Terminal Server CN2600 series device server listens to and that other devices must use to contact the Terminal Server CN2600 series devic… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.3 | NoderedundantCom | |||
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.3.1 | TableredundantComTable | not-accessible | current | The Redundant COM table. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.3.1.1 | RowredundantComEntry | not-accessible | current | The Redundant COM entry. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.3.1.1.1 | ColumnredundantComMaxConnection | read-write | current | Max connection is usually used when the user needs to receive data from different hosts simultaneously. The factory default is 1. In this case, only one specif… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.3.1.1.2 | ColumnredundantComIgnoreJammedIp | read-write | current | Previously, when Max connection was set to a value greater than 1, and the serial device was transmitting data, if any one of the connected hosts stopped respo… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.3.1.1.3 | ColumnredundantComAllowDriverControl | read-write | current | If Max connection is greater than 1, CN2600 will ignore driver control commands from all connected hosts. However, if you set Allow driver control to YES, cont… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.3.1.1.4 | ColumnredundantComConnectionDownRTS | read-write | current | For some applications, serial devices must obtain the Ethernet link status by reading the RTS signal from the Terminal Server CN2600 series device server. If t… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.3.1.1.5 | ColumnredundantComConnectionDownDTR | read-write | current | For some applications, serial devices must obtain the Ethernet link status by reading the DTR signal from the Terminal Server CN2600 series device server. If t… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.4 | Nodedrdas | |||
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.4.1 | TabledrdasTable | not-accessible | current | The DRDAS table. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.4.1.1 | RowdrdasEntry | not-accessible | current | The DRDAS entry. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.4.1.1.1 | ColumndrdasTcpAliveCheck | read-write | current | The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The Terminal Server CN2600 series device serve… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.4.1.1.2 | ColumndrdasInactivityTime | read-write | current | 0 ms: TCP connection is not closed when the serial line is idle. 1-65535 ms: The Terminal Server CN2600 series device server automatically closes the TCP conne… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.4.1.1.3 | ColumndrdasIgnoreJammedIp | read-write | current | Previously, when Max connection was set to a value greater than 1, and the serial device was transmitting data, if any one of the connected hosts stopped respo… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.4.1.1.4 | ColumndrdasPrimaryIpAddress | read-write | current | DRDAS Primary IP Address. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.4.1.1.5 | ColumndrdasBackup1IpAddress | read-write | current | DRDAS Backup 1 IP Address. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.4.1.1.6 | ColumndrdasBackup2IpAddress | read-write | current | DRDAS Backup 2 IP Address. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.4.1.1.7 | ColumndrdasBackup3IpAddress | read-write | current | DRDAS Backup 3 IP Address. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.4.1.1.8 | ColumndrdasTcpPort | read-write | current | The 'TCP port' is the TCP port that the Terminal Server CN2600 series uses to listen to connections, and that other devices must use to contact the Terminal Se… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.4.1.1.9 | ColumndrdasCmdPort | read-write | current | The 'Command port' is a TCP port used to listen for IP-Serial Lib commands from the host. In order to prevent a TCP port conflict with other applications, the … |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.4.1.1.10 | ColumndrdasConnectionDownRTS | read-write | current | For some applications, serial devices must obtain the Ethernet link status by reading the RTS signal from the Terminal Server CN2600 series device server. If t… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.4.1.1.11 | ColumndrdasConnectionDownDTR | read-write | current | For some applications, serial devices must obtain the Ethernet link status by reading the DTR signal from the Terminal Server CN2600 series device server. If t… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.5 | Nodeterminal | |||
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.5.1 | TableterminalTable | not-accessible | current | The Terminal Application table. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.5.1.1 | RowterminalEntry | not-accessible | current | The Terminal Application entry. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.5.1.1.1 | ColumnterminalTcpAliveCheck | read-write | current | The TCP alive check time. 0 min: TCP connection will not be closed if the TCP connection becomes idle. 1 to 99 min: The Terminal Server CN2600 series device se… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.5.1.1.2 | ColumnterminalInactivityTime | read-write | current | 0 min: TCP connection will not be closed if the serial line becomes idle. 0-99 min: The Terminal Server CN2600 series device server automatically closes the TC… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.5.1.1.3 | ColumnterminalAutoLinkProtocol | read-write | current | If Auto-Link protocol is set to 'None,' the Terminal Server CN2600 series will not connect to the host automatically. If Auto-Link protocol is set to 'Telnet,'… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.5.1.1.4 | ColumnterminalPrimaryHostAddress | read-write | current | If specified, designates a 'permanent' host to which the terminal will always be connected. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.5.1.1.5 | ColumnterminalSecondHostAddress | read-write | current | If specified, designates a 'permanent' host to which the terminal will always be connected. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.5.1.1.6 | ColumnterminalTelnetTcpPort | read-write | current | By default, the Telnet TCP port number is set to 23, which is the default TCP port number for Telnet. If you need to telnet to this Terminal Server CN2600 seri… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.5.1.1.7 | ColumnterminalType | read-write | current | Defines the terminal type for outgoing connections. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.5.1.1.8 | ColumnterminalMaxSessions | read-write | current | Configure the max. number of sessions. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.5.1.1.9 | ColumnterminalChangeSession | read-write | current | Defines the control character used to change the terminal session. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.5.1.1.10 | ColumnterminalQuit | read-write | current | Defines the control character used to quit a terminal session. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.5.1.1.11 | ColumnterminalBreak | read-write | current | Defines the control character used to send a Telnet BREAK message. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.5.1.1.12 | ColumnterminalInterrupt | read-write | current | Defines the control character used to send a Telnet INTERRUPT message. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.5.1.1.13 | ColumnterminalAuthenticationType | read-write | current | The terminal authentication type. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.5.1.1.14 | ColumnterminalAutoLoginPrompt | read-write | current | The prompt string for the automatic login ID. When the Terminal Server CN2600 series receives this string from a remote telnet/rlogin server, it will automatic… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.5.1.1.15 | ColumnterminalPasswordPrompt | read-write | current | The prompt string for the automatic login password. When the Terminal Server CN2600 series receives this string from a remote telnet/rlogin server, it will aut… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.5.1.1.16 | ColumnterminalLoginUserName | read-write | current | Terminal login ID for automatic login. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.5.1.1.17 | ColumnterminalLoginPassword | read-write | current | Terminal login password for automatic login. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.6 | NodereverseTerminal | |||
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.6.1 | TablereverseTerminalTable | not-accessible | current | The Reverse Terminal Application table. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.6.1.1 | RowreverseTerminalEntry | not-accessible | current | The Reverse Terminal Application entry. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.6.1.1.1 | ColumnreverseTerminalTcpAliveCheck | read-write | current | The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection becomes idle. 1 to 99 min: The Terminal Server CN2600 series device … |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.6.1.1.2 | ColumnreverseTerminalInactivityTime | read-write | current | 0 min: TCP connection will not be closed if the serial line becomes idle. 0-99 min: The Terminal Server CN2600 series device server automatically closes the TC… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.6.1.1.3 | ColumnreverseTerminalTcpPort | read-write | current | Each of the Terminal Server CN2600 series device server's serial ports are mapped to a TCP port. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.6.1.1.4 | ColumnreverseTerminalAuthenticationType | read-write | current | The reverse terminal authentication type. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.6.1.1.5 | ColumnreverseTerminalMapKeys | read-write | current | If data received through Terminal Server CN2600 series device server's Ethernet port is sent using the 'enter' command, the data will be transmitted out throug… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.7 | Nodedial | |||
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.7.1 | TabledialTable | not-accessible | current | The Dial In/Out table. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.7.1.1 | RowdialEntry | not-accessible | current | The Dial In/Out entry. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.7.1.1.1 | ColumndialTERMBINMode | read-write | current | Select Yes to enable a Binary Terminal connection. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.7.1.1.2 | ColumndialPPPDMode | read-write | current | Select Yes to enable a PPPD connection. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.7.1.1.3 | ColumndialSLIPDMode | read-write | current | Select Yes to enable a SLIPD Terminal connection. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.7.1.1.4 | ColumndialAuthType | read-write | current | The dial in/out authentication type. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.7.1.1.5 | ColumndialDisconnectBy | read-write | current | If this field is set to 'dcd-off,' the connection will be disconnected when the DCD signal is off. If this field is set to 'dsr-off,' the connection will be di… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.7.1.1.6 | ColumndialDestinationIpAddress | read-write | current | Destination IP address is the IP address of the remote dial-in/dial-out server. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.7.1.1.7 | ColumndialSourceIpAddress | read-write | current | Source IP address is IP address of this serial port. The Terminal Server CN2600 series will automatically assign an IP address for the port. We recommend leavi… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.7.1.1.8 | ColumndialIpNetmask | read-write | current | The IP netmask used for dial-in/dial-out networks (PPP or SLIP). |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.7.1.1.9 | ColumndialTcpIpCompression | read-write | current | Depends on whether the remote user's application requests compression. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.7.1.1.10 | ColumndialInactivityTime | read-write | current | 0 ms: TCP connection will not be closed if the serial line becomes idle. 1-65535 ms: The Terminal Server CN2600 series device server automatically closes the T… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.7.1.1.11 | ColumndialLinkQualityReport | read-write | current | Choose YES if you are using software to collect Link quality information. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.7.1.1.12 | ColumndialOutgoingPAPID | read-write | current | Dial-out user ID account. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.7.1.1.13 | ColumndialPAPPassword | read-write | current | Dial-out user password. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.2.7.1.1.14 | ColumndialIncomingPAPCheck | read-write | current | The Dial in/out incoming PAP check type. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.3 | NodedataPacking | |||
| 1.3.6.1.4.1.8691.2.11.1.4.1.3.1 | TabledataPackingPortTable | not-accessible | current | The Data Packing table. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.3.1.1 | RowdataPackingPortEntry | not-accessible | current | The Data Packing entry. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.3.1.1.1 | ColumnportPacketLength | read-write | current | If the value is 0, the Delimiter Process will be used, regardless of the length of the data packet. If the data length (in bytes) matches the configured value,… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.3.1.1.2 | ColumnportDelimiter1Enable | read-write | current | Enable the first delimiter character. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.3.1.1.3 | ColumnportDelimiter1 | read-write | current | The first delimiter character, in hex decimal. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.3.1.1.4 | ColumnportDelimiter2Enable | read-write | current | Enable the second delimiter character. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.3.1.1.5 | ColumnportDelimiter2 | read-write | current | The second delimiter character, in hex decimal. |
| 1.3.6.1.4.1.8691.2.11.1.4.1.3.1.1.6 | ColumnportDelimiterProcess | read-write | current | 'delimiterAddOne' or 'delimiterAddTwo': The data will be transmitted when an additional byte (for 'delimiterAddOne'), or an additional 2 bytes (for 'delimiterA… |
| 1.3.6.1.4.1.8691.2.11.1.4.1.3.1.1.7 | ColumnportForceTransmit | read-write | current | 0: Disable the force transmit timeout. 1 to 65535: Forces the Terminal Server CN2600 series device server's TCP/IP protocol software to try to pack serial data… |
| 1.3.6.1.4.1.8691.2.11.1.4.2 | NodecomParamSetting | |||
| 1.3.6.1.4.1.8691.2.11.1.4.2.1 | TablecomParamPortTable | not-accessible | current | The Communication Parameters table. |
| 1.3.6.1.4.1.8691.2.11.1.4.2.1.1 | RowcomParamPortEntry | not-accessible | current | The Communication Parameters entry. |
| 1.3.6.1.4.1.8691.2.11.1.4.2.1.1.1 | ColumnportAlias | read-write | current | Port alias is included to allow easy identification of the serial devices that are connected to Terminal Server CN2600 series device server's serial port. |
| 1.3.6.1.4.1.8691.2.11.1.4.2.1.1.2 | ColumnportInterface | read-write | current | The serial interface that the port works on. |
| 1.3.6.1.4.1.8691.2.11.1.4.2.1.1.3 | ColumnportBaudRate | read-write | current | The port's speed in bits per second. You can choose a standard baud rate by indexing. |
| 1.3.6.1.4.1.8691.2.11.1.4.2.1.1.4 | ColumnportBaudRateManual | read-write | current | The port's speed in bits per second. You can specify a baud rate manually. |
| 1.3.6.1.4.1.8691.2.11.1.4.2.1.1.5 | ColumnportDataBits | read-write | current | The number of bits in a character for the port. |
| 1.3.6.1.4.1.8691.2.11.1.4.2.1.1.6 | ColumnportStopBits | read-write | current | The number of stop bits for the port. |
| 1.3.6.1.4.1.8691.2.11.1.4.2.1.1.7 | ColumnportParity | read-write | current | The parity bit for the port. |
| 1.3.6.1.4.1.8691.2.11.1.4.2.1.1.8 | ColumnportFlowControl | read-write | current | The flow-control method for the port. |
| 1.3.6.1.4.1.8691.2.11.1.4.2.1.1.9 | ColumnportFIFO | read-write | current | Enable or disable the port's FIFO. |
| 1.3.6.1.4.1.8691.2.11.1.4.3 | NodedataBuffering | |||
| 1.3.6.1.4.1.8691.2.11.1.4.3.1 | TabledataBufferingPortTable | not-accessible | current | The Data Buffering/Log table. |
| 1.3.6.1.4.1.8691.2.11.1.4.3.1.1 | RowdataBufferingPortEntry | not-accessible | current | The Data Buffering/Log entry. |
| 1.3.6.1.4.1.8691.2.11.1.4.3.1.1.1 | ColumnportBufferingEnable | read-write | current | Enable off-line port buffering. |
| 1.3.6.1.4.1.8691.2.11.1.4.3.1.1.2 | ColumnportSerialDataLoggingEnable | read-write | current | Enable or disable serial data logging for the port. |
| 1.3.6.1.4.1.8691.2.11.1.4.4 | NodemodemSettings | |||
| 1.3.6.1.4.1.8691.2.11.1.4.4.1 | TablemodemSettingsPortTable | not-accessible | current | The Modem Settings table. |
| 1.3.6.1.4.1.8691.2.11.1.4.4.1.1 | RowmodemSettingsPortEntry | not-accessible | current | The Modem Settings entry. |
| 1.3.6.1.4.1.8691.2.11.1.4.4.1.1.1 | ColumnportEnableModem | read-write | current | Enable or disable modem for this port. |
| 1.3.6.1.4.1.8691.2.11.1.4.4.1.1.2 | ColumnportInitialString | read-write | current | Set the modem's initial string to establish the connection. E.g., 'AT&S0=1' for auto-answer. |
| 1.3.6.1.4.1.8691.2.11.1.4.4.1.1.3 | ColumnportDialUp | read-write | current | Set the modem's dial-up AT command string. |
| 1.3.6.1.4.1.8691.2.11.1.4.4.1.1.4 | ColumnportPhoneNumber | read-write | current | Set the number used to dial out. |
| 1.3.6.1.4.1.8691.2.11.1.4.5 | NodewelcomeMessage | |||
| 1.3.6.1.4.1.8691.2.11.1.4.5.1 | ScalarportEnableWelcomeMessage | read-write | current | Enable or disable the welcome message. |
| 1.3.6.1.4.1.8691.2.11.1.4.5.2 | ScalarportMessage | read-write | current | Set up a welcome message to greet dial-in users. |
| 1.3.6.1.4.1.8691.2.11.1.5 | NodesysManagement | |||
| 1.3.6.1.4.1.8691.2.11.1.5.1 | NodemiscNetworkSettings | |||
| 1.3.6.1.4.1.8691.2.11.1.5.1.1 | NodeaccessibleIp | |||
| 1.3.6.1.4.1.8691.2.11.1.5.1.1.1 | ScalarenableAccessibleIpList | read-write | current | Enable or disable the entire accessible IP list. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.1.2 | TableaccessibleIpListTable | not-accessible | current | Accessible IP List table. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.1.2.1 | RowaccessibleIpListEntry | not-accessible | current | Accessible IP List entry. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.1.2.1.1 | ColumnaccessibleIpListIndex | read-only | current | Accessible IP List index. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.1.2.1.2 | ColumnactiveAccessibleIpList | read-write | current | Enable or disable this accessible IP entry. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.1.2.1.3 | ColumnaccessibleIpListAddress | read-write | current | Accessible IP address. This value can be the IP address of a single host if the netmask is set to '255.255.255.255,' or it can be a network address. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.1.2.1.4 | ColumnaccessibleIpListNetmask | read-write | current | Accessible IP address netmask. The IP address and netmask are used to specify a group of remote hosts. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.2 | NodesnmpAgentSettings | |||
| 1.3.6.1.4.1.8691.2.11.1.5.1.2.1 | ScalarsnmpEnable | read-write | current | Enable or disable SNMP agent. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.2.2 | ScalarsnmpContactName | read-write | current | The SNMP contact information usually includes an emergency contact name and telephone or pager number. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.2.3 | ScalarsnmpLocation | read-write | current | Specify the location string for SNMP agents, such as the Terminal Server CN2600 series device server. This string is usually set to the street address where th… |
| 1.3.6.1.4.1.8691.2.11.1.5.1.3 | NodedDNS | |||
| 1.3.6.1.4.1.8691.2.11.1.5.1.3.1 | ScalardDNSEnable | read-write | current | Enable or disable the DDNS function. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.3.2 | ScalardDNSServerAddress | read-write | current | The DDNS server address. The DDNS is serviced by a 3-party provider. To use the DDNS function, you may need to obtain a user account from the server. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.3.3 | ScalardDNSHostName | read-write | current | The host name of the machine to be registered to the DDNS server. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.3.4 | ScalardDNSUserName | read-write | current | The user account provided by the DDNS server. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.3.5 | ScalardDNSPassword | read-write | current | The user password provided by the DDNS server. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.4 | NodehostTable | |||
| 1.3.6.1.4.1.8691.2.11.1.5.1.4.1 | TablehostTableTable | not-accessible | current | Host Table. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.4.1.1 | RowhostTableEntry | not-accessible | current | Host Table entry. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.4.1.1.1 | ColumnhostTableIndex | read-only | current | The Host Table index. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.4.1.1.2 | ColumnhostName | read-write | current | The host name of the host table entry. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.4.1.1.3 | ColumnhostIpAddress | read-write | current | Related IP address of the host table entry. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.5 | NoderouteTable | |||
| 1.3.6.1.4.1.8691.2.11.1.5.1.5.1 | TablerouteTableTable | not-accessible | current | Route Table. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.5.1.1 | RowrouteTableEntry | not-accessible | current | Route Table entry. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.5.1.1.1 | ColumnrouteTableIndex | read-only | current | The Route Table index. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.5.1.1.2 | ColumngatewayRouteTable | read-write | current | The gateway property of the route table entry. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.5.1.1.3 | ColumndestinationRouteTable | read-write | current | The destination IP address of the route table entry. This value can be the IP address of a single host if the netmask set to '255.255.255.255,' or it can be a … |
| 1.3.6.1.4.1.8691.2.11.1.5.1.5.1.1.4 | ColumnnetmaskRouteTable | read-write | current | The destination netmask of the route table entry. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.5.1.1.5 | ColumnmetricRouteTable | read-write | current | The routing metric for this route. The semantics of this metric are determined by the routing-protocol. Normally, it represents the cost for the destination. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.5.1.1.6 | ColumninterfaceRouteTable | read-write | current | The value that identifies the local interface through which the next hop of this route should be reached. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.6 | NodeuserTable | |||
| 1.3.6.1.4.1.8691.2.11.1.5.1.6.1 | TableuserTableTable | not-accessible | current | User Table. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.6.1.1 | RowuserTableEntry | not-accessible | current | User Table entry. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.6.1.1.1 | ColumnuserTableIndex | read-only | current | The User Table index. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.6.1.1.2 | ColumnuserNameUserTable | read-write | current | The user name of this entry. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.6.1.1.3 | ColumnpasswordUserTable | read-write | current | The password of this user entry. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.6.1.1.4 | ColumnphoneNumberUserTable | read-write | current | The phone number of this user entry. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.7 | NodeauthenticationServer | |||
| 1.3.6.1.4.1.8691.2.11.1.5.1.7.1 | ScalarradiusServerIp | read-write | current | The IP address or domain name of the RADIUS server. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.7.2 | ScalarradiusKey | read-write | current | RADIUS password. Must be the same as in the RADIUS server. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.7.3 | ScalarudpPortAuthenticationServer | read-write | current | The UDP port of the RADIUS server. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.7.4 | ScalarradiusAccounting | read-write | current | Enable or disable RADIUS accounting. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.8 | NodesysLogSettings | |||
| 1.3.6.1.4.1.8691.2.11.1.5.1.8.1 | ScalarsysLocalLog | read-write | current | Log the following events to the system log: System Cold Start, System Warm Start, Power Down. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.8.2 | ScalarnetworkLocalLog | read-write | current | Log the following events to the system log: DHCP/BOOTP/PPPoE Get IP/Renew, NTP, Mail Fail, NTP Connect Fail, DHCP Fail, IP Conflict, Ethernet Link Down. |
| 1.3.6.1.4.1.8691.2.11.1.5.1.8.3 | ScalarconfigLocalLog | read-write | current | Log the following events to the system log: Login Fail, IP Changed, Password Changed, Config Changed, Firmware Upgrade, SSL Key Import, Config Import, Config E… |
| 1.3.6.1.4.1.8691.2.11.1.5.1.8.4 | ScalaropModeLocalLog | read-write | current | Log the following op-mode events to the system log: Connect, Disconnect, Authentication Fail, Restart. |
| 1.3.6.1.4.1.8691.2.11.1.5.2 | NodeautoWarningSettings | |||
| 1.3.6.1.4.1.8691.2.11.1.5.2.1 | NodeeventSettings | |||
| 1.3.6.1.4.1.8691.2.11.1.5.2.1.1 | ScalarmailWarningColdStart | read-write | current | Refers to starting the system from power off (contrast this with warm start). When performing a cold start, the Terminal Server CN2600 series will automaticall… |
| 1.3.6.1.4.1.8691.2.11.1.5.2.1.2 | ScalarmailWarningWarmStart | read-write | current | Refers to restarting the Terminal Server CN2600 without turning the power off. When performing a warm start, the Terminal Server CN2600 series will automatical… |
| 1.3.6.1.4.1.8691.2.11.1.5.2.1.3 | ScalarmailWarningPower1Down | read-write | current | On dual power model, when power 1 is off, the Terminal Server CN2600 series will immediately send an e-mail. |
| 1.3.6.1.4.1.8691.2.11.1.5.2.1.4 | ScalarmailWarningPower2Down | read-write | current | On dual power model, when power 2 is off, the Terminal Server CN2600 series will immediately send an e-mail. |
| 1.3.6.1.4.1.8691.2.11.1.5.2.1.5 | ScalarmailWarningEthernet1LinkDown | read-write | current | When the built-in link1 port is off, the Terminal Server CN2600 series will immediately send an e-mail. |
| 1.3.6.1.4.1.8691.2.11.1.5.2.1.6 | ScalarmailWarningEthernet2LinkDown | read-write | current | When the built-in link2 port is off, the Terminal Server CN2600 series will immediately send an e-mail. |
| 1.3.6.1.4.1.8691.2.11.1.5.2.1.7 | ScalarmailWarningAuthFailure | read-write | current | The user inputs a wrong password from the Console or Administrator. When authentication failure occurs, the Terminal Server CN2600 series will immediately send… |
| 1.3.6.1.4.1.8691.2.11.1.5.2.1.8 | ScalarmailWarningIpChanged | read-write | current | The user has changed the Terminal Server CN2600 series device server's IP address. When the IP address changes, the Terminal Server CN2600 series will send an … |
| 1.3.6.1.4.1.8691.2.11.1.5.2.1.9 | ScalarmailWarningPasswordChanged | read-write | current | The user has changed the Terminal Server CN2600 series device server's password. When the password changes, the Terminal Server CN2600 series will send an e-ma… |
| 1.3.6.1.4.1.8691.2.11.1.5.2.1.10 | ScalartrapServerColdStart | read-write | current | Refers to starting the system from power off (contrast this with warm start). When performing a cold start, the Terminal Server CN2600 series will automaticall… |
| 1.3.6.1.4.1.8691.2.11.1.5.2.1.11 | ScalartrapServerWarmStart | read-write | current | Refers to restarting the Terminal Server CN2600 without turning the power off. When performing a warm start, the Terminal Server CN2600 series will automatical… |
| 1.3.6.1.4.1.8691.2.11.1.5.2.1.12 | ScalartrapServerEthernet1LinkDown | read-write | current | When the built-in link1 port is off, the Terminal Server CN2600 series will immediately send a SNMP trap. |
| 1.3.6.1.4.1.8691.2.11.1.5.2.1.13 | ScalartrapServerEthernet2LinkDown | read-write | current | When the built-in link2 port is off, the Terminal Server CN2600 series will immediately send a SNMP trap. |
| 1.3.6.1.4.1.8691.2.11.1.5.2.1.14 | ScalartrapServerAuthFailure | read-write | current | The user inputs a wrong password from the Console or Administrator. When authentication failure occurs, the Terminal Server CN2600 series will immediately send… |
| 1.3.6.1.4.1.8691.2.11.1.5.2.2 | NodeserialEventSettings | |||
| 1.3.6.1.4.1.8691.2.11.1.5.2.2.1 | TableportEventSettingsTable | not-accessible | current | Port Event Settings Table. |
| 1.3.6.1.4.1.8691.2.11.1.5.2.2.1.1 | RowportEventSettingsEntry | not-accessible | current | Port Event Settings entry. |
| 1.3.6.1.4.1.8691.2.11.1.5.2.2.1.1.1 | ColumnmailDCDchange | read-write | current | A change in the DCD (Data Carrier Detect) signal indicates that the modem connection status has changed. For example, if the DCD signal changes to low, it indi… |
| 1.3.6.1.4.1.8691.2.11.1.5.2.2.1.1.2 | ColumntrapDCDchange | read-write | current | A change in the DCD (Data Carrier Detect) signal indicates that the modem connection status has changed. For example, if the DCD signal changes to low, it indi… |
| 1.3.6.1.4.1.8691.2.11.1.5.2.2.1.1.3 | ColumnmailDSRchange | read-write | current | A change in the DSR (Data Set Ready) signal indicates that the data communication equipment is powered off. For example, if the DSR signal changes to low, it i… |
| 1.3.6.1.4.1.8691.2.11.1.5.2.2.1.1.4 | ColumntrapDSRchange | read-write | current | A change in the DSR (Data Set Ready) signal indicates that the data communication equipment is powered off. For example, if the DSR signal changes to low, it i… |
| 1.3.6.1.4.1.8691.2.11.1.5.2.3 | NodeemailAlert | |||
| 1.3.6.1.4.1.8691.2.11.1.5.2.3.1 | ScalaremailWarningMailServer | read-write | current | The e-mail server's IP address or domain name of the e-mail warning function. |
| 1.3.6.1.4.1.8691.2.11.1.5.2.3.2 | ScalaremailRequiresAuthentication | read-write | current | Set if the mail server requires user login. |
| 1.3.6.1.4.1.8691.2.11.1.5.2.3.3 | ScalaremailWarningUserName | read-write | current | The user name used to log into the mail server if authentication is required. |
| 1.3.6.1.4.1.8691.2.11.1.5.2.3.4 | ScalaremailWarningPassword | read-write | current | The password used to log into the mail server if authentication is required. |
| 1.3.6.1.4.1.8691.2.11.1.5.2.3.5 | ScalaremailWarningFromEmail | read-write | current | The e-mail address to be filled in the 'From' field of the auto-warning e-mail. |
| 1.3.6.1.4.1.8691.2.11.1.5.2.3.6 | ScalaremailWarningFirstEmailAddr | read-write | current | The first email address to where the auto-warning e-mail is to be sent. |
| 1.3.6.1.4.1.8691.2.11.1.5.2.3.7 | ScalaremailWarningSecondEmailAddr | read-write | current | The second email address to where the auto-warning e-mail is to be sent. |
| 1.3.6.1.4.1.8691.2.11.1.5.2.3.8 | ScalaremailWarningThirdEmailAddr | read-write | current | The third email address to where the auto-warning e-mail is to be sent. |
| 1.3.6.1.4.1.8691.2.11.1.5.2.3.9 | ScalaremailWarningFourthEmailAddr | read-write | current | The fourth email address to where the auto-warning e-mail is to be sent. |
| 1.3.6.1.4.1.8691.2.11.1.5.2.4 | NodesnmpTrap | |||
| 1.3.6.1.4.1.8691.2.11.1.5.2.4.1 | ScalarsnmpTrapReceiverIp | read-write | current | SNMP trap server IP address or domain name. |
| 1.3.6.1.4.1.8691.2.11.1.5.2.4.2 | ScalartrapVersion | read-write | current | SNMP trap version used for the auto-warning function. |
| 1.3.6.1.4.1.8691.2.11.1.5.3 | Nodemaintenance | |||
| 1.3.6.1.4.1.8691.2.11.1.5.3.1 | NodeconsoleSettings | |||
| 1.3.6.1.4.1.8691.2.11.1.5.3.1.1 | ScalarhttpConsole | read-write | current | Enable or disable HTTP console. |
| 1.3.6.1.4.1.8691.2.11.1.5.3.1.2 | ScalarhttpsConsole | read-write | current | Enable or disable HTTPS console. |
| 1.3.6.1.4.1.8691.2.11.1.5.3.1.3 | ScalartelnetConsole | read-write | current | Enable or disable Telnet console. |
| 1.3.6.1.4.1.8691.2.11.1.5.3.1.4 | ScalarsshConsole | read-write | current | Enable or disable SSH console. |
| 1.3.6.1.4.1.8691.2.11.1.5.3.1.5 | ScalarresetButtonFunction | read-write | current | Enable or disable reset button protection. You can disable the hardware reset button after the Terminal Server CN2600 series has been restarted for 60 seconds. |
| 1.3.6.1.4.1.8691.2.11.1.5.3.1.6 | ScalarlcmReadOnlyProtect | read-write | current | Enable or disable LCM read-only protection. If the LCM panel is under read-only protection, users can only view the configurations from the LCM panel. Otherwis… |
| 1.3.6.1.4.1.8691.2.11.1.5.3.2 | NodeloadFactoryDefault | |||
| 1.3.6.1.4.1.8691.2.11.1.5.3.2.1 | ScalarloadFactoryDefaultSetting | write-only | current | This function will reset all of the Terminal Server CN2600 series device server's settings to the factory default values. Be aware that previous settings will … |
| 1.3.6.1.4.1.8691.2.11.1.6 | NodesysStatus | |||
| 1.3.6.1.4.1.8691.2.11.1.6.1 | Nodes2eConnections | |||
| 1.3.6.1.4.1.8691.2.11.1.6.1.1 | TablemonitorRemoteIpTable | not-accessible | current | Serial to Network Connections Remote IP table. |
| 1.3.6.1.4.1.8691.2.11.1.6.1.1.1 | RowmonitorRemoteIpEntry | not-accessible | current | Serial to Network Connections Remote IP entry. |
| 1.3.6.1.4.1.8691.2.11.1.6.1.1.1.1 | ColumnremoteIpIndex | read-only | current | Serial to Network Connections Remote IP index. |
| 1.3.6.1.4.1.8691.2.11.1.6.1.1.1.2 | ColumnmonitorRemoteIp | read-only | current | The remote IP currently connecting to this port. |
| 1.3.6.1.4.1.8691.2.11.1.6.2 | NodeserialPortStatus | |||
| 1.3.6.1.4.1.8691.2.11.1.6.2.1 | TablemonitorSerialPortStatusTable | not-accessible | current | Serial Port Status table. |
| 1.3.6.1.4.1.8691.2.11.1.6.2.1.1 | RowmonitorSerialPortStatusEntry | not-accessible | current | Serial Port Status entry. |
| 1.3.6.1.4.1.8691.2.11.1.6.2.1.1.1 | ColumnmonitorTxCount | read-only | current | View the number of bytes transmitted from the port since the last time the port was initialized. |
| 1.3.6.1.4.1.8691.2.11.1.6.2.1.1.2 | ColumnmonitorRxCount | read-only | current | View the number of bytes received by the port since the last time the port was initialized. |
| 1.3.6.1.4.1.8691.2.11.1.6.2.1.1.3 | ColumnmonitorTxTotalCount | read-only | current | View the number of bytes transmitted from the port since the last time the system was initialized. |
| 1.3.6.1.4.1.8691.2.11.1.6.2.1.1.4 | ColumnmonitorRxTotalCount | read-only | current | View the number of bytes received by the port since the last time the system was initialized. |
| 1.3.6.1.4.1.8691.2.11.1.6.2.1.1.5 | ColumnmonitorDSR | read-only | current | View the current DSR status of this port. |
| 1.3.6.1.4.1.8691.2.11.1.6.2.1.1.6 | ColumnmonitorDTR | read-only | current | View the current DTR status of this port. |
| 1.3.6.1.4.1.8691.2.11.1.6.2.1.1.7 | ColumnmonitorRTS | read-only | current | View the current RTS status of this port. |
| 1.3.6.1.4.1.8691.2.11.1.6.2.1.1.8 | ColumnmonitorCTS | read-only | current | View the current CTS status of this port. |
| 1.3.6.1.4.1.8691.2.11.1.6.2.1.1.9 | ColumnmonitorDCD | read-only | current | View the current DCD status of this port. |
| 1.3.6.1.4.1.8691.2.11.1.6.3 | NodeserialPortErrorCount | |||
| 1.3.6.1.4.1.8691.2.11.1.6.3.1 | TablemonitorSerialPortErrorCountTable | not-accessible | current | Serial Port Error Count table. |
| 1.3.6.1.4.1.8691.2.11.1.6.3.1.1 | RowmonitorSerialPortErrorCountEntry | not-accessible | current | Serial Port Error Count entry. |
| 1.3.6.1.4.1.8691.2.11.1.6.3.1.1.1 | ColumnmonitorErrorCountFrame | read-only | current | View the number of 'Frame' errors for this port. |
| 1.3.6.1.4.1.8691.2.11.1.6.3.1.1.2 | ColumnmonitorErrorCountParity | read-only | current | View the number of 'Parity' errors for this port. |
| 1.3.6.1.4.1.8691.2.11.1.6.3.1.1.3 | ColumnmonitorErrorCountOverrun | read-only | current | View the number of 'Overrun' errors for this port. |
| 1.3.6.1.4.1.8691.2.11.1.6.3.1.1.4 | ColumnmonitorErrorCountBreak | read-only | current | View the number of 'Break' errors for this port. |
| 1.3.6.1.4.1.8691.2.11.1.6.4 | NodeserialPortSettings | |||
| 1.3.6.1.4.1.8691.2.11.1.6.4.1 | TablemonitorSerialPortSettingsTable | not-accessible | current | Serial Port Settings table. |
| 1.3.6.1.4.1.8691.2.11.1.6.4.1.1 | RowmonitorSerialPortSettingsEntry | not-accessible | current | Serial Port Settings entry. |
| 1.3.6.1.4.1.8691.2.11.1.6.4.1.1.1 | ColumnmonitorBaudRate | read-only | current | View the current baudrate of the port. |
| 1.3.6.1.4.1.8691.2.11.1.6.4.1.1.2 | ColumnmonitorDataBits | read-only | current | View the number of bits per byte for the port. |
| 1.3.6.1.4.1.8691.2.11.1.6.4.1.1.3 | ColumnmonitorStopBits | read-only | current | View the number of stop bits for the port. |
| 1.3.6.1.4.1.8691.2.11.1.6.4.1.1.4 | ColumnmonitorParity | read-only | current | View the parity bit for the port. |
| 1.3.6.1.4.1.8691.2.11.1.6.4.1.1.5 | ColumnmonitorRTSCTSFlowControl | read-only | current | View if the port is using RTS/CTS flow control. |
| 1.3.6.1.4.1.8691.2.11.1.6.4.1.1.6 | ColumnmonitorXONXOFFFlowControl | read-only | current | View if the port is using XON/XOFF flow control. |
| 1.3.6.1.4.1.8691.2.11.1.6.4.1.1.7 | ColumnmonitorDTRDSRFlowControl | read-only | current | View if the port is using DTR/DSR flow control. |
| 1.3.6.1.4.1.8691.2.11.1.6.4.1.1.8 | ColumnmonitorFIFO | read-only | current | View FIFO status of this port. |
| 1.3.6.1.4.1.8691.2.11.1.6.4.1.1.9 | ColumnmonitorInterface | read-only | current | View the serial interface that the port is using. |
| 1.3.6.1.4.1.8691.2.11.1.6.5 | NodeserialPortBuffering | |||
| 1.3.6.1.4.1.8691.2.11.1.6.5.1 | TablemonitorSerialPortBufferingTable | not-accessible | current | Serial Port Buffering table. |
| 1.3.6.1.4.1.8691.2.11.1.6.5.1.1 | RowmonitorSerialPortBufferingEntry | not-accessible | current | Serial Port Settings entry. |
| 1.3.6.1.4.1.8691.2.11.1.6.5.1.1.1 | ColumnmonitorBuffering | read-only | current | View length of buffered data for the port. The length unit is byte. |
| 1.3.6.1.4.1.8691.2.11.1.7 | NodesaveConfiguration | |||
| 1.3.6.1.4.1.8691.2.11.1.7.1 | ScalarsaveConfig | write-only | current | Save the applied configuration to the Terminal Server CN2600 series device server. |
| 1.3.6.1.4.1.8691.2.11.1.8 | Noderestart | |||
| 1.3.6.1.4.1.8691.2.11.1.8.1 | ScalarrestartPorts | write-only | current | Restart serial port. Restarting will cause port reseting. |
| 1.3.6.1.4.1.8691.2.11.1.8.2 | ScalarrestartSystem | write-only | current | Restart the Terminal Server CN2600 series device server. Be sure to save all of your configuration changes before you restart the system. Otherwise, all of the… |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| PortList | OCTET STRING | current | Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents… |