MOXA-NP6000-MIB
568 objects
The MIB module for Moxa NPort 6000 Series specific information.
Imported Objects
| SNMPv2-SMI | enterprises IpAddress OBJECT-TYPE |
| SNMPv2-TC | DisplayString MacAddress TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.8691 | Nodemoxa | |||
| 1.3.6.1.4.1.8691.2 | Nodenport | |||
| 1.3.6.1.4.1.8691.2.8 | Identitynp6000 | The MIB module for Moxa NPort 6000 Series specific information. | ||
| 1.3.6.1.4.1.8691.2.8.1 | NodeswMgmt | |||
| 1.3.6.1.4.1.8691.2.8.1.1 | Nodeoverview | |||
| 1.3.6.1.4.1.8691.2.8.1.1.1 | ScalarmodelName | read-only | current | The model name of the NPort. The possible values of this parameter are: 'NP6150' for NPort 6150, 'NP6250' for NPort 6250, 'NP6250-S-SC' for NPort 6250-S-SC, 'N… |
| 1.3.6.1.4.1.8691.2.8.1.1.2 | ScalarserialNumber | read-only | current | The serial number of the NPort. Every NPort 6000 series device server is assigned a unique serial number before it is shipped. |
| 1.3.6.1.4.1.8691.2.8.1.1.3 | ScalarfirmwareVersion | read-only | current | The version of the firmware currently running on the NPort. |
| 1.3.6.1.4.1.8691.2.8.1.1.4 | ScalarmacAddress | read-only | current | The MAC address of the NPort's Ethernet interface. |
| 1.3.6.1.4.1.8691.2.8.1.1.5 | ScalarviewLanSpeed | read-only | current | The current speed and link status of the NPort's built-in LAN port. The possible values are 'No link', '10M/Link,' or '100M/Link.' |
| 1.3.6.1.4.1.8691.2.8.1.1.6 | ScalarviewLanModuleSpeed | read-only | current | The current speed and link status of the the network module's LAN ports, if the module is installed. The value includes two parts. Each part indicates the stat… |
| 1.3.6.1.4.1.8691.2.8.1.1.7 | ScalarupTime | read-only | current | The time (in human-readable notation) since the system was last re-initialized. |
| 1.3.6.1.4.1.8691.2.8.1.1.8 | ScalarmoduleType | read-only | current | The module name currently plugged into the NPort. |
| 1.3.6.1.4.1.8691.2.8.1.1.9 | ScalarmoduleApVersion | read-only | current | The module AP version currently plugged into the NPort. |
| 1.3.6.1.4.1.8691.2.8.1.1.10 | ScalarviewIpv4Address | read-only | current | An IPv4 address is a number assigned to a network device (such as a computer) as a permanent address on the network. Computers use the IP address to identify a… |
| 1.3.6.1.4.1.8691.2.8.1.1.11 | ScalarviewIpv6LinkLocalAddress | read-only | current | An IPv6 Link-Local address is a number assigned to a network device (such as a computer) as a permanent address on the network. Computers use the IP address to… |
| 1.3.6.1.4.1.8691.2.8.1.1.12 | ScalarviewIpv6GlobalAddress | read-only | current | An IPv6 Global address is a number assigned to a network device (such as a computer) as a permanent address on the network. Computers use the IP address to ide… |
| 1.3.6.1.4.1.8691.2.8.1.2 | NodebasicSetting | |||
| 1.3.6.1.4.1.8691.2.8.1.2.1 | NodeserverSetting | |||
| 1.3.6.1.4.1.8691.2.8.1.2.1.1 | ScalarserverName | read-write | current | A text string used to identify the NPort. |
| 1.3.6.1.4.1.8691.2.8.1.2.1.2 | ScalarserverLocation | read-write | current | A text string used to identify the location of the NPort. This option is useful for specifying the location or application of different NPort device servers. |
| 1.3.6.1.4.1.8691.2.8.1.2.2 | NodetimeSetting | |||
| 1.3.6.1.4.1.8691.2.8.1.2.2.1 | ScalartimeZone | read-write | current | The time-zone index of the NPort. |
| 1.3.6.1.4.1.8691.2.8.1.2.2.2 | ScalarlocalTime | read-write | current | The system time in the following format yyyy/mm/dd hh:mm:ss |
| 1.3.6.1.4.1.8691.2.8.1.2.2.3 | ScalartimeServer | read-write | current | The NPort 6000 series device server uses SNTP (RFC-1769) for auto time calibration. Input the correct 'Time server' IP address or domain name. Once the NPort 6… |
| 1.3.6.1.4.1.8691.2.8.1.3 | NodenetworkSetting | |||
| 1.3.6.1.4.1.8691.2.8.1.3.1 | Scalaripv4Configuration | read-write | current | The IPv4 configuration mode of the NPort. You can choose from four possible IP configuration modes: Static, DHCP, DHCP/BOOTP, BOOTP, and PPPoE. |
| 1.3.6.1.4.1.8691.2.8.1.3.2 | Scalaripv4Address | read-write | current | An IPv4 address is a number assigned to a network device (such as a computer) as a permanent address on the network. Computers use the IP address to identify a… |
| 1.3.6.1.4.1.8691.2.8.1.3.3 | Scalaripv4NetMask | read-write | current | A subnet mask represents all of the network hosts at one geographic location, in one building, or on the same local area network. When a packet is sent out ove… |
| 1.3.6.1.4.1.8691.2.8.1.3.4 | Scalaripv4DefaultGateway | read-write | current | A gateway is a network computer that acts as an entrance to another network. Usually, the computers that control traffic within the network or at the local Int… |
| 1.3.6.1.4.1.8691.2.8.1.3.5 | Scalaripv4DnsServer1IpAddr | read-write | current | The first DNS server address. When the user wants to visit a particular website, the computer asks a Domain Name System (DNS) server for the website��s cor… |
| 1.3.6.1.4.1.8691.2.8.1.3.6 | Scalaripv4DnsServer2IpAddr | read-write | current | The second DNS server address. When the user wants to visit a particular website, the computer asks a Domain Name System (DNS) server for the website��s co… |
| 1.3.6.1.4.1.8691.2.8.1.3.7 | Scalaripv4PppoeUserAccount | read-write | current | The user account used by the NPort to access the Internet using PPPoE. For dynamic broad band networks such as xDSL or Cable Modem, users must enter the userna… |
| 1.3.6.1.4.1.8691.2.8.1.3.8 | Scalaripv4PppoePassword | read-write | current | The password used by the NPort to access the Internet using PPPoE. For dynamic broad band networks such as xDSL or Cable Modem, users must enter the username a… |
| 1.3.6.1.4.1.8691.2.8.1.3.9 | Scalaripv4WinsFunction | read-write | current | Enable or disable the WINS server. |
| 1.3.6.1.4.1.8691.2.8.1.3.10 | Scalaripv4WinsServer | read-write | current | If a WINS Server is connected to the network, use this field to record the WINS Server��s IP address. TCP/IP uses IP addresses to identify hosts, but users… |
| 1.3.6.1.4.1.8691.2.8.1.3.11 | Scalarlan1Speed | read-write | current | IEEE802.3 Ethernet supports the auto negotiation speed function to get suitable speeds. However, for connecting to some switches/hubs, the communication speed … |
| 1.3.6.1.4.1.8691.2.8.1.3.12 | ScalarroutingProtocol | read-write | current | The routing protocol used by the NPort. This value could be none, RIP-1, or RIP-2. |
| 1.3.6.1.4.1.8691.2.8.1.3.13 | ScalargratuitousArp | read-write | current | Enable or disable the gratuitous ARP function. For some applications, users need the NPort 6000 series device server to send broadcast packets to update the AR… |
| 1.3.6.1.4.1.8691.2.8.1.3.14 | ScalargratuitousArpSendPeriod | read-write | current | The send period of the gratuitous ARP function. |
| 1.3.6.1.4.1.8691.2.8.1.3.15 | NodemoduleSetting | |||
| 1.3.6.1.4.1.8691.2.8.1.3.15.1 | NoderedundancySetting | |||
| 1.3.6.1.4.1.8691.2.8.1.3.15.1.1 | ScalarredundancyProtocol | read-write | current | This set the redundancy protocol. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.1.2 | NodespanningTree | |||
| 1.3.6.1.4.1.8691.2.8.1.3.15.1.2.1 | ScalarspanningTreeBridgePriority | read-write | current | The bridge priority of spanning tree protocol. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.1.2.2 | ScalarspanningTreeHelloTime | read-write | current | The hello time of spanning tree protocol. Range is 1~10. A Bridge shall enforce the following relationships: 2 x (Forward Delay - 1) >= Max Age Max Age >= 2 x … |
| 1.3.6.1.4.1.8691.2.8.1.3.15.1.2.3 | ScalarspanningTreeForwardingDelay | read-write | current | The forwarding delay of spanning tree protocol. Range is 4~30. A Bridge shall enforce the following relationships: 2 x (Forward Delay - 1) >= Max Age Max Age >… |
| 1.3.6.1.4.1.8691.2.8.1.3.15.1.2.4 | ScalarspanningTreeMaxAge | read-write | current | The max. age of spanning tree protocol. Range is 6~40. A Bridge shall enforce the following relationships: 2 x (Forward Delay - 1) >= Max Age Max Age >= 2 x (H… |
| 1.3.6.1.4.1.8691.2.8.1.3.15.1.2.5 | TablespanningTreePortTable | not-accessible | current | The spanning tree table. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.1.2.5.1 | RowspanningTreePortEntry | not-accessible | current | The spanning tree port entry. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.1.2.5.1.1 | ColumnspanningTreePortIndex | read-only | current | The index of spanning tree table. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.1.2.5.1.2 | ColumnspanningTreePortEnable | read-write | current | This enable of spanning tree protocol for this port. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.1.2.5.1.3 | ColumnspanningTreePortPriority | read-write | current | The port priority of spanning tree protocol. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.1.2.5.1.4 | ColumnspanningTreePortCost | read-write | current | The port cost of spanning tree protocol. Range is 1~20000000. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.1.3 | NodeturboRing | |||
| 1.3.6.1.4.1.8691.2.8.1.3.15.1.3.1 | ScalarturboRingMasterSetup | read-write | current | Set this to be Master. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.1.3.2 | ScalarturboRingRdntPort1 | read-write | current | The port number of 1st Redundant Port on the TURBO RING. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.1.3.3 | ScalarturboRingRdntPort2 | read-write | current | The port number of 2nd Redundant Port on the TURBO RING. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.1.4 | NodeturboRingV2 | |||
| 1.3.6.1.4.1.8691.2.8.1.3.15.1.4.1 | ScalarturboRingV2MasterSetup | read-write | current | Set this to be Master. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.1.4.2 | ScalarturboRingV2RdntPort1 | read-write | current | The port number of 1st Redundant Port on the TURBO RING V2. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.1.4.3 | ScalarturboRingV2RdntPort2 | read-write | current | The port number of 2nd Redundant Port on the TURBO RING V2. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2 | NodegsmGprsSetting | |||
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.1 | ScalargsmGprsType | read-write | current | This set the GSM/GPRS type. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.2 | ScalargsmGprsPIN | read-write | current | This set the PIN of SIM card. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.3 | ScalargsmGprsBand | read-write | current | This set the GSM band. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.4 | NodegsmSetting | |||
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.4.1 | ScalargsmMode | read-write | current | This set the GSM mode. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.4.2 | ScalargsmDestinationIpAddress | read-write | current | Destination IP address is the IP address of the remote dial-in/dial-out server. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.4.3 | ScalargsmSourceIpAddress | read-write | current | Source IP address is IP address of this serial port. The NPort 6000 series device server will automatically assign an IP address for the port. We recommend lea… |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.4.4 | ScalargsmIpNetmask | read-write | current | The IP netmask used for dial-in/dial-out networks. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.4.5 | ScalargsmTcpIpCompression | read-write | current | Depends on whether the remote user's application requests compression. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.4.6 | ScalargsmInactivityTime | read-write | current | 0 ms: TCP connection will not be closed if the serial line becomes idle. 1-65535 ms: The NPort 6000 series device server automatically closes the TCP connectio… |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.4.7 | ScalargsmLinkQualityReport | read-write | current | Choose YES if you are using software to collect Link quality information. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.4.8 | ScalargsmUsername | read-write | current | Dial-out user name. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.4.9 | ScalargsmPassword | read-write | current | Dial-out user password. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.4.10 | ScalargsmAuthenticationType | read-write | current | Dial-in authentication type. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.4.11 | ScalargsmTryNextAuth | read-write | current | Try next type on authentication denied or not. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.4.12 | ScalargsmOutPhoneNumber | read-write | current | Set the number used to dial out. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.4.13 | ScalargsmInitialString | read-write | current | Set the modem's initial string to establish the connection. E.g., 'AT&S0=1' for auto-answer. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write … |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.4.14 | ScalargsmConnectionControl | read-write | current | Set the connect/disconnect condition. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.4.15 | ScalargsmConnectionInterval | read-write | current | Set the connection interval when connect condition is 'periodically connect'. Range is 5~65535 minutes. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not sup… |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.4.16 | ScalargsmPingRemoteHost | read-write | current | Set the remote hostname when connect condition is 'remote host fail'. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.4.17 | ScalargsmInPhoneNumber | read-write | current | Set the number allow to dial in. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.5 | NodegprsSetting | |||
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.5.1 | ScalargprsTcpIpCompression | read-write | current | Depends on whether the remote user's application requests compression. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.5.2 | ScalargprsInactivityTime | read-write | current | 0 ms: TCP connection will not be closed if the serial line becomes idle. 1-65535 ms: The NPort 6000 series device server automatically closes the TCP connectio… |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.5.3 | ScalargprsLinkQualityReport | read-write | current | Choose YES if you are using software to collect Link quality information. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.5.4 | ScalargprsInitialString | read-write | current | Set the modem's initial string to establish the connection. E.g., 'AT&S0=1' for auto-answer. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write … |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.5.5 | ScalargprsUsername | read-write | current | Dial-out user name. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.5.6 | ScalargprsPassword | read-write | current | Dial-out user password. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.5.7 | ScalargprsAPN | read-write | current | Set GPRS APN. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.5.8 | ScalargprsConnectionControl | read-write | current | Set the connect/disconnect condition. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.5.9 | ScalargprsConnectionInterval | read-write | current | Set the connection interval when connect condition is 'periodically connect'. Range is 5~65535 minutes. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not sup… |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.5.10 | ScalargprsPingRemoteHost | read-write | current | Set the remote hostname when connect condition is 'remote host fail'. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.6 | NodesmsSetting | |||
| 1.3.6.1.4.1.8691.2.8.1.3.15.2.6.1 | ScalarsmsFormat | read-write | current | Set SMS format. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.3 | Nodev92ModemSetting | |||
| 1.3.6.1.4.1.8691.2.8.1.3.15.3.1 | Scalarv92ModemMode | read-write | current | This set the modem mode. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.3.2 | Scalarv92ModemDestinationIpAddress | read-write | current | Destination IP address is the IP address of the remote dial-in/dial-out server. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.3.3 | Scalarv92ModemSourceIpAddress | read-write | current | Source IP address is IP address of this serial port. The NPort 6000 series device server will automatically assign an IP address for the port. We recommend lea… |
| 1.3.6.1.4.1.8691.2.8.1.3.15.3.4 | Scalarv92ModemIpNetmask | read-write | current | The IP netmask used for dial-in/dial-out networks. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.3.5 | Scalarv92ModemTcpIpCompression | read-write | current | Depends on whether the remote user's application requests compression. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.3.6 | Scalarv92ModemInactivityTime | read-write | current | 0 ms: TCP connection will not be closed if the serial line becomes idle. 1-65535 ms: The NPort 6000 series device server automatically closes the TCP connectio… |
| 1.3.6.1.4.1.8691.2.8.1.3.15.3.7 | Scalarv92ModemLinkQualityReport | read-write | current | Choose YES if you are using software to collect Link quality information. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.3.8 | Scalarv92ModemUsername | read-write | current | Dial-out user ID account. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.3.9 | Scalarv92ModemPassword | read-write | current | Dial-out user password. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.3.10 | Scalarv92ModemIncomingPAPCheck | read-write | current | The Dial in/out incoming PAP check type. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.3.11 | Scalarv92ModemIncomingTryNextAuth | read-write | current | Try next type on authentication denied or not. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.3.12 | Scalarv92ModemPhoneNumber | read-write | current | Set the number used to dial out. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.3.13 | Scalarv92ModemInitialString | read-write | current | Set the modem's initial string to establish the connection. E.g., 'AT&S0=1' for auto-answer. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write … |
| 1.3.6.1.4.1.8691.2.8.1.3.15.3.14 | Scalarv92ModemConnectionControl | read-write | current | Set the connect/disconnect condition. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.15.3.15 | Scalarv92ModemConnectionInterval | read-write | current | Set the connection interval when connect condition is 'periodically connect'. Range is 5~65535 minutes. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not sup… |
| 1.3.6.1.4.1.8691.2.8.1.3.15.3.16 | Scalarv92ModemPingRemoteHost | read-write | current | Set the remote hostname when connect condition is 'remote host fail'. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.3.16 | Scalaripv6Configuration | read-write | current | The IPv6 configuration mode of the NPort. You can choose from four possible IP configuration modes: Auto, DHCPv6, Static, Disable. |
| 1.3.6.1.4.1.8691.2.8.1.3.17 | Scalaripv6Address | read-write | current | An IPv6 address is a number assigned to a network device (such as a computer) as a permanent address on the network. Computers use the IP address to identify a… |
| 1.3.6.1.4.1.8691.2.8.1.3.18 | Scalaripv6Prefix | read-write | current | A prefix represents all of the network hosts at one geographic location, in one building, or on the same local area network. When a packet is sent out over the… |
| 1.3.6.1.4.1.8691.2.8.1.3.19 | Scalaripv6DefaultGateway | read-write | current | A gateway is a network computer that acts as an entrance to another network. Usually, the computers that control traffic within the network or at the local Int… |
| 1.3.6.1.4.1.8691.2.8.1.3.20 | Scalaripv6DnsServer1IpAddr | read-write | current | The first DNS server address. When the user wants to visit a particular website, the computer asks a Domain Name System (DNS) server for the website��s cor… |
| 1.3.6.1.4.1.8691.2.8.1.3.21 | Scalaripv6DnsServer2IpAddr | read-write | current | The second DNS server address. When the user wants to visit a particular website, the computer asks a Domain Name System (DNS) server for the website��s co… |
| 1.3.6.1.4.1.8691.2.8.1.3.22 | ScalarconnectionPriority | read-write | current | This value determines which DNS record are used in first priority. |
| 1.3.6.1.4.1.8691.2.8.1.4 | NodeportSetting | |||
| 1.3.6.1.4.1.8691.2.8.1.4.1 | NodeopModeSetting | |||
| 1.3.6.1.4.1.8691.2.8.1.4.1.1 | NodeopMode | |||
| 1.3.6.1.4.1.8691.2.8.1.4.1.1.1 | TableopModePortTable | not-accessible | current | The serial ports' operation mode table. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.1.1.1 | RowopModePortEntry | not-accessible | current | The serial port's operation mode entry. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.1.1.1.1 | ColumnportIndex | read-only | current | The serial port index. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.1.1.1.2 | ColumnportApplication | read-write | current | The application of the serial port. Note that changing this setting may also change the operation mode. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.1.1.1.3 | ColumnportMode | read-write | current | The operation mode of the serial port. Note that changing this setting may also change the application. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2 | Nodeapplication | |||
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1 | NodedeviceControl | |||
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1 | TabledeviceControlTable | not-accessible | current | The Device Control application table. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1 | RowdeviceControlEntry | not-accessible | current | The Device Control application entry. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.1 | ColumndeviceControlTcpAliveCheck | read-write | current | The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort 6000 series device server automatica… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.2 | ColumndeviceControlMaxConnection | read-write | current | Max connection is usually used when the user needs to receive data from different hosts simultaneously. The factory default is 1. In this case, only one specif… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.3 | ColumndeviceControlIgnoreJammedIp | read-write | current | Previously, when Max connection was set to a value greater than 1, and the serial device was transmitting data, if any one of the connected hosts stopped respo… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.4 | ColumndeviceControlAllowDriverControl | read-write | current | If Max connection is greater than 1, NPort will ignore driver control commands from all connected hosts. However, if you set Allow driver control to YES, contr… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.5 | ColumndeviceControlCommandByCommandOperation | read-write | current | Commands will be sent from the NPort to the serial device. After each command, the NPort will wait to receive a response before sending the next command. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.6 | ColumndeviceControlSecure | read-write | current | If 'Secure' is enabled, the data on the Ethernet will be encrypted with SSL. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.7 | ColumndeviceControlConnectionDownRTS | read-write | current | For some applications, serial devices must obtain the Ethernet link status by reading the RTS signal from the NPort 6000 series device server. If this setting … |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.8 | ColumndeviceControlConnectionDownDTR | read-write | current | For some applications, serial devices must obtain the Ethernet link status by reading the DTR signal from the NPort 6000 series device server. If this setting … |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.9 | ColumndeviceControlResponseTimeout | read-write | current | After sending a command to the serial device, the NPort will wait for a response. If no response is received from the serial device within the specified time, … |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.10 | ColumndeviceControlNonRequestSerialData | read-write | current | This specifies how the NPort will handle data that is received from a serial device that is not a response to a command. The NPort can either discard such data… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.11 | ColumndeviceControlTcpPort | read-write | current | The 'TCP port' is the TCP port that the NPort 6000 series device server uses to listen to connections, and that other devices must use to contact the NPort 600… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.12 | ColumndeviceControlDestinationAddress1 | read-write | current | The NPort 6000 series device server can connect actively to a remote host that has this IP address. This setting is used in Reverse RealCOM mode. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.13 | ColumndeviceControlDestinationTcpPort1 | read-write | current | The NPort 6000 series device server can connect actively to a remote host that has this TCP data port number. This setting is used in Reverse RealCOM mode. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.14 | ColumndeviceControlDestinationCmdPort1 | read-write | current | The NPort 6000 series device server can connect actively to a remote host that has this TCP command port number. This setting is used in Reverse RealCOM mode. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.15 | ColumndeviceControlDestinationAddress2 | read-write | current | The NPort 6000 series device server can connect actively to a remote host that has this IP address. This setting is used in Reverse RealCOM mode. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.16 | ColumndeviceControlDestinationTcpPort2 | read-write | current | The NPort 6000 series device server can connect actively to a remote host that has this TCP data port number. This setting is used in Reverse RealCOM mode. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.17 | ColumndeviceControlDestinationCmdPort2 | read-write | current | The NPort 6000 series device server can connect actively to a remote host that has this TCP command port number. This setting is used in Reverse RealCOM mode. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.18 | ColumndeviceControlDesignatedLocalTcpPort1 | read-write | current | The local TCP data port used to connect actively to the remote host. This setting is used in Reverse RealCOM mode. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.19 | ColumndeviceControlDesignatedLocalCmdPort1 | read-write | current | The local TCP command port used to connect actively to the remote host. This setting is used in Reverse RealCOM mode. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.20 | ColumndeviceControlDesignatedLocalTcpPort2 | read-write | current | The local TCP data port used to connect actively to the remote host. This setting is used in Reverse RealCOM mode. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.21 | ColumndeviceControlDesignatedLocalCmdPort2 | read-write | current | The local TCP command port used to connect actively to the remote host. This setting is used in Reverse RealCOM mode. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2 | Nodesocket | |||
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1 | TablesocketTable | not-accessible | current | The Socket application table. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1 | RowsocketEntry | not-accessible | current | The Socket application entry. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.1 | ColumnsocketTcpAliveCheck | read-write | current | The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort 6000 series device server automatica… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.2 | ColumnsocketInactivityTime | read-write | current | 0 ms: TCP connection is not closed when the serial line is idle. 1-65535 ms: The NPort 6000 series device server automatically closes the TCP connection if the… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.3 | ColumnsocketMaxConnection | read-write | current | Max connection is usually used when the user needs to receive data from different hosts simultaneously. The factory default is 1. In this case, only one specif… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.4 | ColumnsocketIgnoreJammedIp | read-write | current | Previously, when Max connection was set to a value greater than 1, and the serial device was transmitting data, if any one of the connected hosts stopped respo… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.5 | ColumnsocketAllowDriverControl | read-write | current | If Max connection is greater than 1, NPort will ignore driver control commands from all connected hosts. However, if you set Allow driver control to YES, contr… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.6 | ColumnsocketCommandByCommandOperation | read-write | current | Commands will be sent from the NPort to the serial device. After each command, the NPort will wait to receive a response before sending the next command. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.7 | ColumnsocketSecure | read-write | current | If Secure is enabled, data sent over the Ethernet will be encrypted with SSL. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.8 | ColumnsocketTcpPort | read-write | current | The 'TCP port' is the TCP port that the NPort 6000 series device server uses to listen to connections, and that other devices must use to contact the NPort 600… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.9 | ColumnsocketCmdPort | read-write | current | The 'Command port' is a TCP port used to listen for IP-Serial Lib commands from the host. In order to prevent a TCP port conflict with other applications, the … |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.10 | ColumnsocketTcpServerConnectionDownRTS | read-write | current | For some applications, serial devices must obtain the Ethernet link status from the RTS signal sent by the NPort 6000 series device server. If this setting is … |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.11 | ColumnsocketTcpServerConnectionDownDTR | read-write | current | For some applications, serial devices must obtain the Ethernet link status from the DTR signal sent by the NPort 6000 series device server. If this setting is … |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.12 | ColumnsocketResponseTimeout | read-write | current | After sending a command to the serial device, the NPort will wait for a response. If no response is received from the serial device within the specified time, … |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.13 | ColumnsocketNonRequestSerialData | read-write | current | This specifies how the NPort will handle data that is received from a serial device that is not a response to a command. The NPort can either discard such data… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.14 | ColumnsocketTcpClientDestinationAddress1 | read-write | current | The NPort 6000 series device server can connect actively to a remote host that has this IP address. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.15 | ColumnsocketTcpClientDestinationPort1 | read-write | current | The NPort 6000 series device server can connect actively to a remote host that has this TCP port number. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.16 | ColumnsocketTcpClientDestinationAddress2 | read-write | current | The NPort 6000 series device server can connect actively to a remote host that has this IP address. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.17 | ColumnsocketTcpClientDestinationPort2 | read-write | current | The NPort 6000 series device server can connect actively to a remote host that has this TCP port number. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.18 | ColumnsocketTcpClientDestinationAddress3 | read-write | current | The NPort 6000 series device server can connect actively to a remote host that has this IP address. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.19 | ColumnsocketTcpClientDestinationPort3 | read-write | current | The NPort 6000 series device server can connect actively to a remote host that has this port number. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.20 | ColumnsocketTcpClientDestinationAddress4 | read-write | current | The NPort 6000 series device server can connect actively to a remote host that has this IP address. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.21 | ColumnsocketTcpClientDestinationPort4 | read-write | current | The NPort 6000 series device server can connect actively to a remote host that has this port number. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.22 | ColumnsocketTcpClientDesignatedLocalPort1 | read-write | current | The local TCP port used to connect actively to the remote host. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.23 | ColumnsocketTcpClientDesignatedLocalPort2 | read-write | current | The local TCP port used to connect actively to the remote host. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.24 | ColumnsocketTcpClientDesignatedLocalPort3 | read-write | current | The local TCP port used to connect actively to the remote host. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.25 | ColumnsocketTcpClientDesignatedLocalPort4 | read-write | current | The local TCP port used to connect actively to the remote host. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.26 | ColumnsocketTcpClientConnectionControl | read-write | current | Events that cause the TCP client to drop the connection. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.27 | ColumnsocketUdpDestinationAddress1Begin | read-write | current | The NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and socketUdpDesti… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.28 | ColumnsocketUdpDestinationAddress1End | read-write | current | The NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between socketUdpDestinationAddress1Begin… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.29 | ColumnsocketUdpDestinationPort1 | read-write | current | The NPort 6000 series device server can actively send UDP packets to remote hosts that have this port number. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.30 | ColumnsocketUdpDestinationAddress2Begin | read-write | current | The NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and socketUdpDesti… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.31 | ColumnsocketUdpDestinationAddress2End | read-write | current | The NPort 6000 series device server can actively send UDP packets to the remote hosts whose IP addresses are in the range between socketUdpDestinationAddress2B… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.32 | ColumnsocketUdpDestinationPort2 | read-write | current | The NPort 6000 series device server can actively send UDP packets to the remote hosts that have this TCP port number. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.33 | ColumnsocketUdpDestinationAddress3Begin | read-write | current | The NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and socketUdpDesti… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.34 | ColumnsocketUdpDestinationAddress3End | read-write | current | The NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between socketUdpDestinationAddress3Begin… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.35 | ColumnsocketUdpDestinationPort3 | read-write | current | The NPort 6000 series device server can actively send UDP packets to remote hosts that have this TCP port number. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.36 | ColumnsocketUdpDestinationAddress4Begin | read-write | current | The NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and socketUdpDesti… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.37 | ColumnsocketUdpDestinationAddress4End | read-write | current | The NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between socketUdpDestinationAddress4Begin… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.38 | ColumnsocketUdpDestinationPort4 | read-write | current | The NPort 6000 series device server can actively send UDP packets to remote hosts that have this TCP port number. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.39 | ColumnsocketUdpLocalListenPort | read-write | current | The UDP port that the NPort 6000 series device server listens to and that other devices must use to contact the NPort 6000 series device server. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.40 | ColumnsocketUDPDynamicDst | read-write | current | If enable Dynamic Destination, the target address is decieded by the source address of the last received data. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.41 | ColumnsocketUDPDynamicDstTimeout | read-write | current | 0 ms: The target address will be changed every time. 1-65535 ms: The target address will be occupied before the source address idle for a period of time. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.3 | NodepairConnection | |||
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1 | TablepairConnectionTable | not-accessible | current | The Pair Connection table. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1 | RowpairConnectionEntry | not-accessible | current | The Pair Connection entry. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.1 | ColumnpairConnectionTcpAliveCheck | read-write | current | The TCP alive check time. 0 min: TCP connection will not be closed if the TCP connection becomes idle. 1 to 99 min: The NPort 6000 series device server automat… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.2 | ColumnpairConnectionSecure | read-write | current | If Secure is enabled, the Ethernet data will be encrypted using SSL. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.3 | ColumnpairConnectionDestinationAddress | read-write | current | The Pair Connection 'Master' will contact the network host that has the specified IP address. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.4 | ColumnpairConnectionDestinationPort | read-write | current | Data will be transmitted through the specified port number. Note that you must configure the same TCP port number for the device server acting as the Pair Conn… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.5 | ColumnpairConnectionTcpPort | read-write | current | This port number must be the same port number that was set up for the Pair Connection 'Master' device server. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.4 | NodeethernetModem | |||
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.4.1 | TableethernetModemTable | not-accessible | current | The Ethernet Modem table. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.4.1.1 | RowethernetModemEntry | not-accessible | current | The Ethernet Modem entry. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.4.1.1.1 | ColumnethernetModemTcpAliveCheck | read-write | current | The TCP alive check time. 0 min: TCP connection will not be closed if the TCP connection becomes idle. 1 to 99 min: The NPort 6000 series device server automat… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.4.1.1.2 | ColumnethernetModemTcpPort | read-write | current | The local TCP port used to listen for incoming calls from a remote ethernet modem. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5 | Nodeterminal | |||
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1 | TableterminalTable | not-accessible | current | The Terminal Application table. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1 | RowterminalEntry | not-accessible | current | The Terminal Application entry. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.1 | ColumnterminalTcpAliveCheck | read-write | current | The TCP alive check time. 0 min: TCP connection will not be closed if the TCP connection becomes idle. 1 to 99 min: The NPort 6000 series device server automat… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.2 | ColumnterminalInactivityTime | read-write | current | 0 min: TCP connection will not be closed if the serial line becomes idle. 0-99 min: The NPort 6000 series device server automatically closes the TCP connection… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.3 | ColumnterminalAutoLinkProtocol | read-write | current | If Auto-Link protocol is set to 'None,' the NPort 6000 series device server will not connect to the host automatically. If Auto-Link protocol is set to 'Telnet… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.4 | ColumnterminalPrimaryHostAddress | read-write | current | If specified, designates a 'permanent' host to which the terminal will always be connected. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.5 | ColumnterminalSecondHostAddress | read-write | current | If specified, designates a 'permanent' host to which the terminal will always be connected. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.6 | ColumnterminalTelnetTcpPort | read-write | current | By default, the Telnet TCP port number is set to 23, which is the default TCP port number for Telnet. If you need to telnet to this NPort 6000 series device se… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.7 | ColumnterminalSshTcpPort | read-write | current | By default, the SSH TCP port number is set to 22, which is the default TCP port number for SSH. If you need to use SSH to connect to this NPort 6000 series dev… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.8 | ColumnterminalType | read-write | current | Defines the terminal type for outgoing connections. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.9 | ColumnterminalMaxSessions | read-write | current | Configure the max. number of sessions. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.10 | ColumnterminalChangeSession | read-write | current | Defines the control character used to change the terminal session. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.11 | ColumnterminalQuit | read-write | current | Defines the control character used to quit a terminal session. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.12 | ColumnterminalBreak | read-write | current | Defines the control character used to send a Telnet BREAK message. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.13 | ColumnterminalInterrupt | read-write | current | Defines the control character used to send a Telnet INTERRUPT message. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.14 | ColumnterminalAuthenticationType | read-write | current | The terminal authentication type. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.15 | ColumnterminalTryNextAuth | read-write | current | Try next type on authentication denied or not |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.16 | ColumnterminalAutoLoginPrompt | read-write | current | The prompt string for the automatic login ID. When the NPort 6000 series device server receives this string from a remote telnet/rlogin server, it will automat… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.17 | ColumnterminalPasswordPrompt | read-write | current | The prompt string for the automatic login password. When the NPort 6000 series device server receives this string from a remote telnet/rlogin server, it will a… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.18 | ColumnterminalLoginUserName | read-write | current | Terminal login ID for automatic login. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.19 | ColumnterminalLoginPassword | read-write | current | Terminal login password for automatic login. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.6 | NodereverseTerminal | |||
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1 | TablereverseTerminalTable | not-accessible | current | The Reverse Terminal Application table. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1 | RowreverseTerminalEntry | not-accessible | current | The Reverse Terminal Application entry. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.1 | ColumnreverseTerminalTcpAliveCheck | read-write | current | The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection becomes idle. 1 to 99 min: The NPort 6000 series device server autom… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.2 | ColumnreverseTerminalInactivityTime | read-write | current | 0 min: TCP connection will not be closed if the serial line becomes idle. 0-99 min: The NPort 6000 series device server automatically closes the TCP connection… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.3 | ColumnreverseTerminalTcpPort | read-write | current | Each of the NPort 6000 series device server's serial ports are mapped to a TCP port. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.4 | ColumnreverseTerminalAuthenticationType | read-write | current | The reverse terminal authentication type. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.5 | ColumnreverseTerminalTryNextAuth | read-write | current | Try next type on authentication denied or not |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.6 | ColumnreverseTerminalMapKeys | read-write | current | If data received through NPort 6000 series device server's Ethernet port is sent using the 'enter' command, the data will be transmitted out through the serial… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.7 | Nodeprinter | |||
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1 | TableprinterTable | not-accessible | current | The Printer Application table. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1 | RowprinterEntry | not-accessible | current | The Printer Application entry. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.1 | ColumnprinterTcpAliveCheck | read-write | current | The TCP alive check time. 0 min: TCP connection will not be closed if the TCP connection becomes idle. 1 to 99 min: The NPort 6000 series device server automat… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.2 | ColumnprinterTcpPort | read-only | current | The host uses this value to determine the Group to which the printer attached to this serial port belongs. These values are fixed, and cannot be changed by the… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.3 | ColumnprinterGroup | read-write | current | Groups printers attached to different ports. Printers in the same group will share the printing load for printing requests to that group of printers. E.g., set… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.4 | ColumnprinterQueueNameRaw | read-write | current | Specify the name of the print queue (in RAW mode). |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.5 | ColumnprinterQueueNameASCII | read-write | current | Specify the name of the print queue (in ASCII mode). |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.6 | ColumnprinterAppendFormFeed | read-write | current | Specify paging. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.8 | Nodedial | |||
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1 | TabledialTable | not-accessible | current | The Dial In/Out table. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1 | RowdialEntry | not-accessible | current | The Dial In/Out entry. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.1 | ColumndialTERMBINMode | read-write | current | Select Yes to enable a Binary Terminal connection. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.2 | ColumndialPPPDMode | read-write | current | Select Yes to enable a PPPD connection. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.3 | ColumndialSLIPDMode | read-write | current | Select Yes to enable a SLIPD Terminal connection. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.4 | ColumndialAuthType | read-write | current | The dial in/out authentication type. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.5 | ColumndialTryNextAuth | read-write | current | Try next type on authentication denied or not |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.6 | ColumndialDisconnectBy | read-write | current | If this field is set to 'dcd-off,' the connection will be disconnected when the DCD signal is off. If this field is set to 'dsr-off,' the connection will be di… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.7 | ColumndialDestinationIpAddress | read-write | current | Destination IP address is the IP address of the remote dial-in/dial-out server. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.8 | ColumndialSourceIpAddress | read-write | current | Source IP address is IP address of this serial port. The NPort 6000 series device server will automatically assign an IP address for the port. We recommend lea… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.9 | ColumndialIpNetmask | read-write | current | The IP netmask used for dial-in/dial-out networks (PPP or SLIP). |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.10 | ColumndialTcpIpCompression | read-write | current | Depends on whether the remote user's application requests compression. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.11 | ColumndialInactivityTime | read-write | current | 0 ms: TCP connection will not be closed if the serial line becomes idle. 1-65535 ms: The NPort 6000 series device server automatically closes the TCP connectio… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.12 | ColumndialLinkQualityReport | read-write | current | Choose YES if you are using software to collect Link quality information. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.13 | ColumndialUsername | read-write | current | Dial-out user ID account. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.14 | ColumndialPassword | read-write | current | Dial-out user password. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.15 | ColumndialIncomingPAPCheck | read-write | current | The Dial in/out incoming PAP check type. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.16 | ColumndialIncomingTryNextAuth | read-write | current | Try next type on authentication denied or not |
| 1.3.6.1.4.1.8691.2.8.1.4.1.3 | NodedataPacking | |||
| 1.3.6.1.4.1.8691.2.8.1.4.1.3.1 | TabledataPackingPortTable | not-accessible | current | The Data Packing table. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1 | RowdataPackingPortEntry | not-accessible | current | The Data Packing entry. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.1 | ColumnportPacketLength | read-write | current | If the value is 0, the Delimiter Process will be used, regardless of the length of the data packet. If the data length (in bytes) matches the configured value,… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.2 | ColumnportDelimiter1Enable | read-write | current | Enable the first delimiter character. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.3 | ColumnportDelimiter1 | read-write | current | The first delimiter character, in hex decimal. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.4 | ColumnportDelimiter2Enable | read-write | current | Enable the second delimiter character. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.5 | ColumnportDelimiter2 | read-write | current | The second delimiter character, in hex decimal. |
| 1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.6 | ColumnportDelimiterProcess | read-write | current | 'delimiterAddOne' or 'delimiterAddTwo': The data will be transmitted when an additional byte (for 'delimiterAddOne'), or an additional 2 bytes (for 'delimiterA… |
| 1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.7 | ColumnportForceTransmit | read-write | current | 0: Disable the force transmit timeout. 1 to 65535: Forces the NPort 6000 series device server's TCP/IP protocol software to try to pack serial data received du… |
| 1.3.6.1.4.1.8691.2.8.1.4.2 | NodecomParamSetting | |||
| 1.3.6.1.4.1.8691.2.8.1.4.2.1 | TablecomParamPortTable | not-accessible | current | The Communication Parameters table. |
| 1.3.6.1.4.1.8691.2.8.1.4.2.1.1 | RowcomParamPortEntry | not-accessible | current | The Communication Parameters entry. |
| 1.3.6.1.4.1.8691.2.8.1.4.2.1.1.1 | ColumnportAlias | read-write | current | Port alias is included to allow easy identification of the serial devices that are connected to NPort 6000 series device server's serial port. |
| 1.3.6.1.4.1.8691.2.8.1.4.2.1.1.2 | ColumnportInterface | read-write | current | The serial interface that the port works on. |
| 1.3.6.1.4.1.8691.2.8.1.4.2.1.1.3 | ColumnportBaudRate | read-write | current | The port's speed in bits per second. You can choose a standard baud rate by indexing. |
| 1.3.6.1.4.1.8691.2.8.1.4.2.1.1.4 | ColumnportBaudRateManual | read-write | current | The port's speed in bits per second. You can specify a baud rate manually. |
| 1.3.6.1.4.1.8691.2.8.1.4.2.1.1.5 | ColumnportDataBits | read-write | current | The number of bits in a character for the port. |
| 1.3.6.1.4.1.8691.2.8.1.4.2.1.1.6 | ColumnportStopBits | read-write | current | The number of stop bits for the port. |
| 1.3.6.1.4.1.8691.2.8.1.4.2.1.1.7 | ColumnportParity | read-write | current | The parity bit for the port. |
| 1.3.6.1.4.1.8691.2.8.1.4.2.1.1.8 | ColumnportFlowControl | read-write | current | The flow-control method for the port. |
| 1.3.6.1.4.1.8691.2.8.1.4.2.1.1.9 | ColumnportFIFO | read-write | current | Enable or disable the port's FIFO. |
| 1.3.6.1.4.1.8691.2.8.1.4.2.1.1.10 | ColumnportOnDelay | read-write | current | The port's RTS toggle On delay time (ms). |
| 1.3.6.1.4.1.8691.2.8.1.4.2.1.1.11 | ColumnportOffDelay | read-write | current | The port's RTS toggle Off delay time (ms). |
| 1.3.6.1.4.1.8691.2.8.1.4.3 | NodedataBuffering | |||
| 1.3.6.1.4.1.8691.2.8.1.4.3.1 | TabledataBufferingPortTable | not-accessible | current | The Data Buffering/Log table. |
| 1.3.6.1.4.1.8691.2.8.1.4.3.1.1 | RowdataBufferingPortEntry | not-accessible | current | The Data Buffering/Log entry. |
| 1.3.6.1.4.1.8691.2.8.1.4.3.1.1.1 | ColumnportBufferingEnable | read-write | current | Enable off-line port buffering. |
| 1.3.6.1.4.1.8691.2.8.1.4.3.1.1.2 | ColumnportBufferingLocation | read-write | current | The location of off-line port buffering. Note: NPort 6150 can not be set as sdCard. |
| 1.3.6.1.4.1.8691.2.8.1.4.3.1.1.3 | ColumnportBufferingSDFileSize | read-write | current | The maximum file size of off-line port buffering, in MBytes, if the location is set to 'sdCard.' Note: NPort 6150 do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.4.3.1.1.4 | ColumnportSerialDataLoggingEnable | read-write | current | Enable or disable serial data logging for the port. |
| 1.3.6.1.4.1.8691.2.8.1.4.4 | NodemodemSettings | |||
| 1.3.6.1.4.1.8691.2.8.1.4.4.1 | TablemodemSettingsPortTable | not-accessible | current | The Modem Settings table. |
| 1.3.6.1.4.1.8691.2.8.1.4.4.1.1 | RowmodemSettingsPortEntry | not-accessible | current | The Modem Settings entry. |
| 1.3.6.1.4.1.8691.2.8.1.4.4.1.1.1 | ColumnportEnableModem | read-write | current | Enable or disable modem for this port. |
| 1.3.6.1.4.1.8691.2.8.1.4.4.1.1.2 | ColumnportInitialString | read-write | current | Set the modem's initial string to establish the connection. E.g., 'AT&S0=1' for auto-answer. |
| 1.3.6.1.4.1.8691.2.8.1.4.4.1.1.3 | ColumnportDialUp | read-write | current | Set the modem's dial-up AT command string. |
| 1.3.6.1.4.1.8691.2.8.1.4.4.1.1.4 | ColumnportPhoneNumber | read-write | current | Set the number used to dial out. |
| 1.3.6.1.4.1.8691.2.8.1.4.5 | NodecipherSettings | |||
| 1.3.6.1.4.1.8691.2.8.1.4.5.1 | TablecipherSettingsPortTable | not-accessible | current | The Cipher Settings table. |
| 1.3.6.1.4.1.8691.2.8.1.4.5.1.1 | RowcipherSettingsPortEntry | not-accessible | current | The Cipher Settings entry. |
| 1.3.6.1.4.1.8691.2.8.1.4.5.1.1.1 | ColumnsslCipherSort | read-write | current | SSL cipher sorting. The format is '2,0,1,3,5,6,8,9,4,7' for example. The index mapping of each cipher method is shown blow. EDH-RSA-DES-CBC3-SHA(2) has the hig… |
| 1.3.6.1.4.1.8691.2.8.1.4.5.1.1.2 | ColumnsshCipherSort | read-write | current | SSL cipher sorting. The format is '2,0,1,3,5,4,6,7' for example. The index mapping of each cipher method is shown blow. aes192-cbc(2) has the highest priority … |
| 1.3.6.1.4.1.8691.2.8.1.4.6 | NodewelcomeMessage | |||
| 1.3.6.1.4.1.8691.2.8.1.4.6.1 | ScalarportEnableWelcomeMessage | read-write | current | Enable or disable the welcome message. |
| 1.3.6.1.4.1.8691.2.8.1.4.6.2 | ScalarportMessage | read-write | current | Set up a welcome message to greet dial-in users. |
| 1.3.6.1.4.1.8691.2.8.1.5 | NodesysManagement | |||
| 1.3.6.1.4.1.8691.2.8.1.5.1 | NodemiscNetworkSettings | |||
| 1.3.6.1.4.1.8691.2.8.1.5.1.1 | NodeaccessibleIp | |||
| 1.3.6.1.4.1.8691.2.8.1.5.1.1.1 | ScalarenableAccessibleIpList | read-write | current | Enable or disable the entire accessible IP list. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.1.2 | TableaccessibleIpListTable | not-accessible | current | Accessible IP List table. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1 | RowaccessibleIpListEntry | not-accessible | current | Accessible IP List entry. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1.1 | ColumnaccessibleIpListIndex | read-only | current | Accessible IP List index. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1.2 | ColumnactiveAccessibleIpList | read-write | current | Enable or disable this accessible IP entry. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1.3 | ColumnaccessibleIpListAddress | read-write | current | Accessible IP address. This value can be the IP address of a single host if the netmask is set to '255.255.255.255,' or it can be a network address. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1.4 | ColumnaccessibleIpListNetmask | read-write | current | Accessible IP address netmask. The IP address and netmask are used to specify a group of remote hosts. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.2 | NodesnmpAgentSettings | |||
| 1.3.6.1.4.1.8691.2.8.1.5.1.2.1 | ScalarsnmpEnable | read-write | current | Enable or disable SNMP agent. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.2.2 | ScalarsnmpContactName | read-write | current | The SNMP contact information usually includes an emergency contact name and telephone or pager number. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.2.3 | ScalarsnmpLocation | read-write | current | Specify the location string for SNMP agents, such as the NPort 6000 series device server. This string is usually set to the street address where the NPort 6000… |
| 1.3.6.1.4.1.8691.2.8.1.5.1.3 | NodedDNS | |||
| 1.3.6.1.4.1.8691.2.8.1.5.1.3.1 | ScalardDNSEnable | read-write | current | Enable or disable the DDNS function. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.3.2 | ScalardDNSServerAddress | read-write | current | The DDNS server address. The DDNS is serviced by a 3-party provider. To use the DDNS function, you may need to obtain a user account from the server. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.3.3 | ScalardDNSHostName | read-write | current | The host name of the machine to be registered to the DDNS server. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.3.4 | ScalardDNSUserName | read-write | current | The user account provided by the DDNS server. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.3.5 | ScalardDNSPassword | read-write | current | The user password provided by the DDNS server. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.4 | NodehostTable | |||
| 1.3.6.1.4.1.8691.2.8.1.5.1.4.1 | TablehostTableTable | not-accessible | current | Host Table. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.4.1.1 | RowhostTableEntry | not-accessible | current | Host Table entry. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.4.1.1.1 | ColumnhostTableIndex | read-only | current | The Host Table index. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.4.1.1.2 | ColumnhostName | read-write | current | The host name of the host table entry. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.4.1.1.3 | ColumnhostIpAddress | read-write | current | Related IP address of the host table entry. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.5 | NoderouteTable | |||
| 1.3.6.1.4.1.8691.2.8.1.5.1.5.1 | TablerouteTableTable | not-accessible | current | Route Table. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1 | RowrouteTableEntry | not-accessible | current | Route Table entry. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.1 | ColumnrouteTableIndex | read-only | current | The Route Table index. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.2 | ColumngatewayRouteTable | read-write | current | The gateway property of the route table entry. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.3 | ColumndestinationRouteTable | read-write | current | The destination IP address of the route table entry. This value can be the IP address of a single host if the netmask set to '255.255.255.255,' or it can be a … |
| 1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.4 | ColumnnetmaskRouteTable | read-write | current | The destination netmask of the route table entry. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.5 | ColumnmetricRouteTable | read-write | current | The routing metric for this route. The semantics of this metric are determined by the routing-protocol. Normally, it represents the cost for the destination. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.6 | ColumninterfaceRouteTable | read-write | current | The value that identifies the local interface through which the next hop of this route should be reached. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.6 | NodeuserTable | |||
| 1.3.6.1.4.1.8691.2.8.1.5.1.6.1 | TableuserTableTable | not-accessible | current | User Table. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1 | RowuserTableEntry | not-accessible | current | User Table entry. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1.1 | ColumnuserTableIndex | read-only | current | The User Table index. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1.2 | ColumnuserNameUserTable | read-write | current | The user name of this entry. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1.3 | ColumnpasswordUserTable | read-write | current | The password of this user entry. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1.4 | ColumnphoneNumberUserTable | read-write | current | The phone number of this user entry. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.7 | NodeauthenticationServer | |||
| 1.3.6.1.4.1.8691.2.8.1.5.1.7.1 | ScalarradiusServerIp | read-write | current | The IP address or domain name of the RADIUS server. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.7.2 | ScalarradiusKey | read-write | current | RADIUS password. Must be the same as in the RADIUS server. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.7.3 | ScalarudpPortAuthenticationServer | read-write | current | The UDP port of the RADIUS server. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.7.4 | ScalarradiusAccounting | read-write | current | Enable or disable RADIUS accounting. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.7.5 | ScalartacacsPlusServerIp | read-write | current | The IP address or domain name of the TACACS+ server. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.7.6 | ScalartacacsPlusSecret | read-write | current | TACACS+ shared secret. Must be the same as in the TACACS+ server. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.7.7 | ScalartacacsPlusAccounting | read-write | current | Enable or disable TACACS+ accounting. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.8 | NodesysLogSettings | |||
| 1.3.6.1.4.1.8691.2.8.1.5.1.8.1 | ScalarsysLocalLog | read-write | current | Log the following events to the system log: System Cold Start, System Warm Start. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.8.2 | ScalarnetworkLocalLog | read-write | current | Log the following events to the system log: DHCP/BOOTP/PPPoE Get IP/Renew, NTP, Mail Fail, NTP Connect Fail, DHCP Fail, IP Conflict, Ethernet Link Down. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.8.3 | ScalarconfigLocalLog | read-write | current | Log the following events to the system log: Login Fail, IP Changed, Password Changed, Config Changed, Firmware Upgrade, SSL Key Import, Config Import, Config E… |
| 1.3.6.1.4.1.8691.2.8.1.5.1.8.4 | ScalaropModeLocalLog | read-write | current | Log the following op-mode events to the system log: Connect, Disconnect, Authentication Fail, Restart. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.8.5 | ScalarsysRemoteLog | read-write | current | Log the following events to the remote log server: System Cold Start, System Warm Start. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.8.6 | ScalarnetworkRemoteLog | read-write | current | Log the following events to the remote log server: DHCP/BOOTP/PPPoE Get IP/Renew, NTP, Mail Fail, NTP Connect Fail, DHCP Fail, IP Conflict, Ethernet Link Down. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.8.7 | ScalarconfigRemoteLog | read-write | current | Log the following events to the remote log server: Login Fail, IP Changed, Password Changed, Config Changed, Firmware Upgrade, SSL Key Import, Config Import, C… |
| 1.3.6.1.4.1.8691.2.8.1.5.1.8.8 | ScalaropModeRemoteLog | read-write | current | Log the following op-mode events to the remote log server: Connect, Disconnect, Authentication Fail, Restart. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.9 | NoderemoteLogServer | |||
| 1.3.6.1.4.1.8691.2.8.1.5.1.9.1 | ScalarsyslogServerIp | read-write | current | The IP address or domain name of the SYSLOG server. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.9.2 | ScalarsyslogFacility | read-write | current | The SYSLOG facility level. |
| 1.3.6.1.4.1.8691.2.8.1.5.1.9.3 | ScalarsyslogSeverity | read-write | current | The SYSLOG severity level. |
| 1.3.6.1.4.1.8691.2.8.1.5.2 | NodeautoWarningSettings | |||
| 1.3.6.1.4.1.8691.2.8.1.5.2.1 | NodeeventSettings | |||
| 1.3.6.1.4.1.8691.2.8.1.5.2.1.1 | ScalarmailWarningColdStart | read-write | current | Refers to starting the system from power off (contrast this with warm start). When performing a cold start, the NPort 6000 series device server will automatica… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.1.2 | ScalarmailWarningWarmStart | read-write | current | Refers to restarting the NPort 6000 without turning the power off. When performing a warm start, the NPort 6000 series device server will automatically send an… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.1.3 | ScalarmailWarningAuthFailure | read-write | current | The user inputs a wrong password from the Console or Administrator. When authentication failure occurs, the NPort 6000 series device server will immediately se… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.1.4 | ScalarmailWarningIpChanged | read-write | current | The user has changed the NPort 6000 series device server's IP address. When the IP address changes, the NPort 6000 series device server will send an e-mail wit… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.1.5 | ScalarmailWarningPasswordChanged | read-write | current | The user has changed the NPort 6000 series device server's password. When the password changes, the NPort 6000 series device server will send an e-mail with th… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.1.6 | ScalartrapServerColdStart | read-write | current | Refers to starting the system from power off (contrast this with warm start). When performing a cold start, the NPort 6000 series device server will automatica… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.1.7 | ScalartrapServerWarmStart | read-write | current | Refers to restarting the NPort 6000 without turning the power off. When performing a warm start, the NPort 6000 series device server will automatically send an… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.1.8 | ScalartrapServerAuthFailure | read-write | current | The user inputs a wrong password from the Console or Administrator. When authentication failure occurs, the NPort 6000 series device server will immediately se… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.1.9 | ScalaralarmServerEthernet1LinkDown | read-write | current | When the built-in link1 port is off, the NPort 6000 series device server will automatically raise a d-out alarm. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC d… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.1.10 | ScalaralarmServerEthernet2LinkDown | read-write | current | The 6000 series device server can provide an extra Ethernet port via the network module. When the first port on the network module is off, the NPort 6000 serie… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.1.11 | ScalaralarmServerEthernet3LinkDown | read-write | current | The NPort 6000 series device server can provide an extra Ethernet port via the network module. When the second port on the network module is off, the NPort 600… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.1.12 | ScalarsmsServerColdStart | read-write | current | Refers to starting the system from power off (contrast this with warm start). When performing a cold start, the NPort 6000 series device server will automatica… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.1.13 | ScalarsmsServerWarmStart | read-write | current | Refers to restarting the NPort 6000 without turning the power off. When performing a warm start, the NPort 6000 series device server will automatically send a … |
| 1.3.6.1.4.1.8691.2.8.1.5.2.1.14 | ScalarsmsServerEthernet1LinkDown | read-write | current | When the built-in link1 port is off, the NPort 6000 series device server will automatically send a SMS alarm. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do n… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.1.15 | ScalarsmsServerEthernet2LinkDown | read-write | current | The NPort 6000 series device server can provide an extra Ethernet port via the network module. When the first port on the network module is off, the NPort 6000… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.1.16 | ScalarsmsServerEthernet3LinkDown | read-write | current | The NPort 6000 series device server can provide an extra Ethernet port via the network module. When the second port on the network module is off, the NPort 600… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.1.17 | ScalarsmsServerAuthFailure | read-write | current | The user inputs a wrong password from the Console or Administrator. When authentication failure occurs, the NPort 6000 series device server will immediately se… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.1.18 | ScalarsmsServerIpChanged | read-write | current | The user has changed the NPort 6000 series device server's IP address. When the IP address changes, the NPort 6000 series device server will send a SMS with th… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.1.19 | ScalarsmsServerPasswordChanged | read-write | current | The user has changed the NPort 6000 series device server's password. When the password changes, the NPort 6000 series device server will send a SMS with the pa… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.2 | NodeserialEventSettings | |||
| 1.3.6.1.4.1.8691.2.8.1.5.2.2.1 | TableportEventSettingsTable | not-accessible | current | Port Event Settings Table. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1 | RowportEventSettingsEntry | not-accessible | current | Port Event Settings entry. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.1 | ColumnmailDCDchange | read-write | current | A change in the DCD (Data Carrier Detect) signal indicates that the modem connection status has changed. For example, if the DCD signal changes to low, it indi… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.2 | ColumntrapDCDchange | read-write | current | A change in the DCD (Data Carrier Detect) signal indicates that the modem connection status has changed. For example, if the DCD signal changes to low, it indi… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.3 | ColumnalarmDCDchange | read-write | current | A change in the DCD (Data Carrier Detect) signal indicates that the modem connection status has changed. For example, if the DCD signal changes to low, it indi… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.4 | ColumnsmsDCDchange | read-write | current | A change in the DCD (Data Carrier Detect) signal indicates that the modem connection status has changed. For example, if the DCD signal changes to low, it indi… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.5 | ColumnmailDSRchange | read-write | current | A change in the DSR (Data Set Ready) signal indicates that the data communication equipment is powered off. For example, if the DSR signal changes to low, it i… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.6 | ColumntrapDSRchange | read-write | current | A change in the DSR (Data Set Ready) signal indicates that the data communication equipment is powered off. For example, if the DSR signal changes to low, it i… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.7 | ColumnalarmDSRchange | read-write | current | A change in the DSR (Data Set Ready) signal indicates that the data communication equipment is powered off. For example, if the DSR signal changes to low, it i… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.8 | ColumnsmsDSRchange | read-write | current | A change in the DSR (Data Set Ready) signal indicates that the data communication equipment is powered off. For example, if the DSR signal changes to low, it i… |
| 1.3.6.1.4.1.8691.2.8.1.5.2.3 | NodeemailAlert | |||
| 1.3.6.1.4.1.8691.2.8.1.5.2.3.1 | ScalaremailWarningMailServer | read-write | current | The e-mail server's IP address or domain name of the e-mail warning function. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.3.2 | ScalaremailRequiresAuthentication | read-write | current | Set if the mail server requires user login. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.3.3 | ScalaremailWarningUserName | read-write | current | The user name used to log into the mail server if authentication is required. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.3.4 | ScalaremailWarningPassword | read-write | current | The password used to log into the mail server if authentication is required. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.3.5 | ScalaremailWarningFromEmail | read-write | current | The e-mail address to be filled in the 'From' field of the auto-warning e-mail. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.3.6 | ScalaremailWarningFirstEmailAddr | read-write | current | The first email address to where the auto-warning e-mail is to be sent. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.3.7 | ScalaremailWarningSecondEmailAddr | read-write | current | The second email address to where the auto-warning e-mail is to be sent. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.3.8 | ScalaremailWarningThirdEmailAddr | read-write | current | The third email address to where the auto-warning e-mail is to be sent. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.3.9 | ScalaremailWarningFourthEmailAddr | read-write | current | The fourth email address to where the auto-warning e-mail is to be sent. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.4 | NodesnmpTrap | |||
| 1.3.6.1.4.1.8691.2.8.1.5.2.4.1 | ScalarsnmpTrapReceiverIp | read-write | current | SNMP trap server IP address or domain name. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.4.2 | ScalartrapVersion | read-write | current | SNMP trap version used for the auto-warning function. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.5 | NodesmsAlert | |||
| 1.3.6.1.4.1.8691.2.8.1.5.2.5.1 | ScalarsmsAlertFirstPhoneNumber | read-write | current | The first phone number to where the auto-warning SMS is to be sent. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.5.2 | ScalarsmsAlertSecondPhoneNumber | read-write | current | The second phone number to where the auto-warning SMS is to be sent. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.5.3 | ScalarsmsAlertThirdPhoneNumber | read-write | current | The third phone number to where the auto-warning SMS is to be sent. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.5.4 | ScalarsmsAlertFourthPhoneNumber | read-write | current | The fourth phone number to where the auto-warning SMS is to be sent. Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC do not support write access. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.6 | NodeeventLogSettings | |||
| 1.3.6.1.4.1.8691.2.8.1.5.2.6.1 | ScalarcurrentLogCapacityRatio | read-only | current | The current usage ratio of log capacity. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.6.2 | ScalarlogCapacityWarningEnable | read-write | current | Enable/disable the log capacity warning. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.6.3 | ScalarlogCapacityWarningThreshold | read-write | current | The log capacity warning threshold. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.6.4 | ScalarmailLogCapacity | read-write | current | The log capacity warning which alerts user by mail message. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.6.5 | ScalartrapLogCapacity | read-write | current | The log capacity warning which alerts user by SNMP trap. |
| 1.3.6.1.4.1.8691.2.8.1.5.2.6.6 | ScalarlogOversizeAction | read-write | current | The event log oversize actions. |
| 1.3.6.1.4.1.8691.2.8.1.5.3 | Nodemaintenance | |||
| 1.3.6.1.4.1.8691.2.8.1.5.3.1 | NodeconsoleSettings | |||
| 1.3.6.1.4.1.8691.2.8.1.5.3.1.1 | ScalarhttpConsole | read-write | current | Enable or disable HTTP console. |
| 1.3.6.1.4.1.8691.2.8.1.5.3.1.2 | ScalarhttpsConsole | read-write | current | Enable or disable HTTPS console. |
| 1.3.6.1.4.1.8691.2.8.1.5.3.1.3 | ScalartelnetConsole | read-write | current | Enable or disable Telnet console. |
| 1.3.6.1.4.1.8691.2.8.1.5.3.1.4 | ScalarsshConsole | read-write | current | Enable or disable SSH console. |
| 1.3.6.1.4.1.8691.2.8.1.5.3.1.5 | ScalarconsoleAuthenticationType | read-write | current | The console authentication type. |
| 1.3.6.1.4.1.8691.2.8.1.5.3.1.6 | ScalartryNextTypeOnAuthDenied | read-write | current | Try next type on authentication denied or not |
| 1.3.6.1.4.1.8691.2.8.1.5.3.1.7 | ScalarresetButtonFunction | read-write | current | Enable or disable reset button protection. You can disable the hardware reset button after the NPort 6000 series device server has been restarted for 60 second… |
| 1.3.6.1.4.1.8691.2.8.1.5.3.1.8 | ScalarlcmReadOnlyProtect | read-write | current | Enable or disable LCM read-only protection. If the LCM panel is under read-only protection, users can only view the configurations from the LCM panel. Otherwis… |
| 1.3.6.1.4.1.8691.2.8.1.5.3.1.9 | ScalarmaxHttpLoginUsers | read-write | current | The maximum login users for HTTP/HTTPS. |
| 1.3.6.1.4.1.8691.2.8.1.5.3.1.10 | ScalarautoLogoutSetting | read-write | current | Auto logout setting (ms) |
| 1.3.6.1.4.1.8691.2.8.1.5.3.2 | NodeloadFactoryDefault | |||
| 1.3.6.1.4.1.8691.2.8.1.5.3.2.1 | ScalarloadFactoryDefaultSetting | write-only | current | This function will reset all of the NPort 6000 series device server's settings to the factory default values. Be aware that previous settings will be lost. Sel… |
| 1.3.6.1.4.1.8691.2.8.1.5.4 | NodeaccountManagement | |||
| 1.3.6.1.4.1.8691.2.8.1.5.4.1 | NodenotificationMessage | |||
| 1.3.6.1.4.1.8691.2.8.1.5.4.1.1 | ScalarloginNotificationMessage | read-write | current | Login notification message. |
| 1.3.6.1.4.1.8691.2.8.1.5.4.1.2 | ScalarloginFailureMessage | read-write | current | Login failure message. |
| 1.3.6.1.4.1.8691.2.8.1.5.4.2 | NodeuserAccount | |||
| 1.3.6.1.4.1.8691.2.8.1.5.4.2.1 | TableuserAccountTable | not-accessible | current | User account list |
| 1.3.6.1.4.1.8691.2.8.1.5.4.2.1.1 | RowuserAccountEntry | not-accessible | current | User account list entry |
| 1.3.6.1.4.1.8691.2.8.1.5.4.2.1.1.1 | ColumnuserAccountIndex | read-only | current | The Host Table index. |
| 1.3.6.1.4.1.8691.2.8.1.5.4.2.1.1.2 | ColumnactiveUserAccount | read-write | current | The user account is activate or not. |
| 1.3.6.1.4.1.8691.2.8.1.5.4.2.1.1.3 | ColumnaccountName | read-write | current | Name of user account |
| 1.3.6.1.4.1.8691.2.8.1.5.4.2.1.1.4 | ColumnaccountGroupName | read-write | current | Group name of user account |
| 1.3.6.1.4.1.8691.2.8.1.5.4.3 | NodeaccessPermission | |||
| 1.3.6.1.4.1.8691.2.8.1.5.4.3.1 | TableaccessPermissionTable | not-accessible | current | Access permission list |
| 1.3.6.1.4.1.8691.2.8.1.5.4.3.1.1 | RowaccessPermissionEntry | not-accessible | current | Access permission list entry |
| 1.3.6.1.4.1.8691.2.8.1.5.4.3.1.1.1 | ColumngroupName | read-write | current | Group name |
| 1.3.6.1.4.1.8691.2.8.1.5.4.3.1.1.2 | ColumnnetworkConfig | read-write | current | Access permission of network configuration group |
| 1.3.6.1.4.1.8691.2.8.1.5.4.3.1.1.3 | ColumnserialConfig | read-write | current | Access permission of serial configuration group |
| 1.3.6.1.4.1.8691.2.8.1.5.4.3.1.1.4 | ColumnsystemConfig | read-write | current | Access permission of system configuration group |
| 1.3.6.1.4.1.8691.2.8.1.5.4.3.1.1.5 | ColumnadminConfig | read-write | current | Access permission of administration group |
| 1.3.6.1.4.1.8691.2.8.1.5.4.3.1.1.6 | ColumnmonitorLogWarning | read-write | current | Access permission of log monitoring group |
| 1.3.6.1.4.1.8691.2.8.1.5.4.3.1.1.7 | ColumncommonSetting | read-write | current | Access permission of common setting group |
| 1.3.6.1.4.1.8691.2.8.1.5.4.4 | NodeaccountPasswordAndLoginMgmt | |||
| 1.3.6.1.4.1.8691.2.8.1.5.4.4.1 | NodeaccountPasswordPolicy | |||
| 1.3.6.1.4.1.8691.2.8.1.5.4.4.1.1 | ScalarpwdMinLength | read-write | current | The minimum length of password. |
| 1.3.6.1.4.1.8691.2.8.1.5.4.4.1.2 | ScalarpwdComplexityCheckEnable | read-write | current | Enable or disable password complexity check |
| 1.3.6.1.4.1.8691.2.8.1.5.4.4.1.3 | ScalarpwdComplexityCheckDigitEnable | read-write | current | Enable or disable digit check |
| 1.3.6.1.4.1.8691.2.8.1.5.4.4.1.4 | ScalarpwdComplexityCheckAlphabetEnable | read-write | current | Enable or disable alphabet check |
| 1.3.6.1.4.1.8691.2.8.1.5.4.4.1.5 | ScalarpwdComplexityCheckSpecialCharEnable | read-write | current | Enable or disable special letter check |
| 1.3.6.1.4.1.8691.2.8.1.5.4.4.1.6 | ScalarpwdLifetime | read-write | current | Password life time |
| 1.3.6.1.4.1.8691.2.8.1.5.4.4.2 | NodeaccountLoginFailureLockout | |||
| 1.3.6.1.4.1.8691.2.8.1.5.4.4.2.1 | ScalarloginFailureLockoutEnable | read-write | current | Enable or disable lockout when login failure |
| 1.3.6.1.4.1.8691.2.8.1.5.4.4.2.2 | ScalarloginFailureLockoutRetrys | read-write | current | The login lockout after fail retry over the count. |
| 1.3.6.1.4.1.8691.2.8.1.5.4.4.2.3 | ScalarloginFailureLockoutTime | read-write | current | The lockout time after fail retry over the count. |
| 1.3.6.1.4.1.8691.2.8.1.6 | NodesysStatus | |||
| 1.3.6.1.4.1.8691.2.8.1.6.1 | Nodes2eConnections | |||
| 1.3.6.1.4.1.8691.2.8.1.6.1.1 | TablemonitorRemoteIpTable | not-accessible | current | Serial to Network Connections Remote IP table. |
| 1.3.6.1.4.1.8691.2.8.1.6.1.1.1 | RowmonitorRemoteIpEntry | not-accessible | current | Serial to Network Connections Remote IP entry. |
| 1.3.6.1.4.1.8691.2.8.1.6.1.1.1.1 | ColumnremoteIpIndex | read-only | current | Serial to Network Connections Remote IP index. |
| 1.3.6.1.4.1.8691.2.8.1.6.1.1.1.2 | ColumnmonitorRemoteIp | read-only | current | The remote IP currently connecting to this port. |
| 1.3.6.1.4.1.8691.2.8.1.6.1.1.1.3 | ColumnmonitorCipher | read-only | current | Currently used cipher for this connection if secure mode is enabled. |
| 1.3.6.1.4.1.8691.2.8.1.6.2 | NodeserialPortStatus | |||
| 1.3.6.1.4.1.8691.2.8.1.6.2.1 | TablemonitorSerialPortStatusTable | not-accessible | current | Serial Port Status table. |
| 1.3.6.1.4.1.8691.2.8.1.6.2.1.1 | RowmonitorSerialPortStatusEntry | not-accessible | current | Serial Port Status entry. |
| 1.3.6.1.4.1.8691.2.8.1.6.2.1.1.1 | ColumnmonitorTxCount | read-only | current | View the number of bytes transmitted from the port since the last time the port was initialized. |
| 1.3.6.1.4.1.8691.2.8.1.6.2.1.1.2 | ColumnmonitorRxCount | read-only | current | View the number of bytes received by the port since the last time the port was initialized. |
| 1.3.6.1.4.1.8691.2.8.1.6.2.1.1.3 | ColumnmonitorTxTotalCount | read-only | current | View the number of bytes transmitted from the port since the last time the system was initialized. |
| 1.3.6.1.4.1.8691.2.8.1.6.2.1.1.4 | ColumnmonitorRxTotalCount | read-only | current | View the number of bytes received by the port since the last time the system was initialized. |
| 1.3.6.1.4.1.8691.2.8.1.6.2.1.1.5 | ColumnmonitorDSR | read-only | current | View the current DSR status of this port. |
| 1.3.6.1.4.1.8691.2.8.1.6.2.1.1.6 | ColumnmonitorDTR | read-only | current | View the current DTR status of this port. |
| 1.3.6.1.4.1.8691.2.8.1.6.2.1.1.7 | ColumnmonitorRTS | read-only | current | View the current RTS status of this port. |
| 1.3.6.1.4.1.8691.2.8.1.6.2.1.1.8 | ColumnmonitorCTS | read-only | current | View the current CTS status of this port. |
| 1.3.6.1.4.1.8691.2.8.1.6.2.1.1.9 | ColumnmonitorDCD | read-only | current | View the current DCD status of this port. |
| 1.3.6.1.4.1.8691.2.8.1.6.3 | NodeserialPortErrorCount | |||
| 1.3.6.1.4.1.8691.2.8.1.6.3.1 | TablemonitorSerialPortErrorCountTable | not-accessible | current | Serial Port Error Count table. |
| 1.3.6.1.4.1.8691.2.8.1.6.3.1.1 | RowmonitorSerialPortErrorCountEntry | not-accessible | current | Serial Port Error Count entry. |
| 1.3.6.1.4.1.8691.2.8.1.6.3.1.1.1 | ColumnmonitorErrorCountFrame | read-only | current | View the number of 'Frame' errors for this port. |
| 1.3.6.1.4.1.8691.2.8.1.6.3.1.1.2 | ColumnmonitorErrorCountParity | read-only | current | View the number of 'Parity' errors for this port. |
| 1.3.6.1.4.1.8691.2.8.1.6.3.1.1.3 | ColumnmonitorErrorCountOverrun | read-only | current | View the number of 'Overrun' errors for this port. |
| 1.3.6.1.4.1.8691.2.8.1.6.3.1.1.4 | ColumnmonitorErrorCountBreak | read-only | current | View the number of 'Break' errors for this port. |
| 1.3.6.1.4.1.8691.2.8.1.6.4 | NodeserialPortSettings | |||
| 1.3.6.1.4.1.8691.2.8.1.6.4.1 | TablemonitorSerialPortSettingsTable | not-accessible | current | Serial Port Settings table. |
| 1.3.6.1.4.1.8691.2.8.1.6.4.1.1 | RowmonitorSerialPortSettingsEntry | not-accessible | current | Serial Port Settings entry. |
| 1.3.6.1.4.1.8691.2.8.1.6.4.1.1.1 | ColumnmonitorBaudRate | read-only | current | View the current baudrate of the port. |
| 1.3.6.1.4.1.8691.2.8.1.6.4.1.1.2 | ColumnmonitorDataBits | read-only | current | View the number of bits per byte for the port. |
| 1.3.6.1.4.1.8691.2.8.1.6.4.1.1.3 | ColumnmonitorStopBits | read-only | current | View the number of stop bits for the port. |
| 1.3.6.1.4.1.8691.2.8.1.6.4.1.1.4 | ColumnmonitorParity | read-only | current | View the parity bit for the port. |
| 1.3.6.1.4.1.8691.2.8.1.6.4.1.1.5 | ColumnmonitorRTSCTSFlowControl | read-only | current | View if the port is using RTS/CTS flow control. |
| 1.3.6.1.4.1.8691.2.8.1.6.4.1.1.6 | ColumnmonitorXONXOFFFlowControl | read-only | current | View if the port is using XON/XOFF flow control. |
| 1.3.6.1.4.1.8691.2.8.1.6.4.1.1.7 | ColumnmonitorDTRDSRFlowControl | read-only | current | View if the port is using DTR/DSR flow control. |
| 1.3.6.1.4.1.8691.2.8.1.6.4.1.1.8 | ColumnmonitorRTSToggleFlowControl | read-only | current | View if the port is using RTS toggle flow control. |
| 1.3.6.1.4.1.8691.2.8.1.6.4.1.1.9 | ColumnmonitorFIFO | read-only | current | View FIFO status of this port. |
| 1.3.6.1.4.1.8691.2.8.1.6.4.1.1.10 | ColumnmonitorInterface | read-only | current | View the serial interface that the port is using. |
| 1.3.6.1.4.1.8691.2.8.1.6.5 | NodeserialPortBuffering | |||
| 1.3.6.1.4.1.8691.2.8.1.6.5.1 | TablemonitorSerialPortBufferingTable | not-accessible | current | Serial Port Buffering table. |
| 1.3.6.1.4.1.8691.2.8.1.6.5.1.1 | RowmonitorSerialPortBufferingEntry | not-accessible | current | Serial Port Settings entry. |
| 1.3.6.1.4.1.8691.2.8.1.6.5.1.1.1 | ColumnmonitorBuffering | read-only | current | View length of buffered data for the port. The length unit is byte. |
| 1.3.6.1.4.1.8691.2.8.1.6.6 | NoderelayOutputStatus | |||
| 1.3.6.1.4.1.8691.2.8.1.6.6.1 | ScalarrelayOutputEthernet1LinkDown | read-only | current | The relay dout status of the event that the built- in LAN port is off. |
| 1.3.6.1.4.1.8691.2.8.1.6.6.2 | Scalarethernet1LinkDownAcknowledge | write-only | current | Acknowledge the event that the built-in LAN port is off. Acknowledgement will clear the d-out alarm before you can actually fix the problem. |
| 1.3.6.1.4.1.8691.2.8.1.6.6.3 | ScalarrelayOutputEthernet2LinkDown | read-only | current | The relay dout status of the event that the first LAN port of the network module is off. |
| 1.3.6.1.4.1.8691.2.8.1.6.6.4 | Scalarethernet2LinkDownAcknowledge | write-only | current | Acknowledge the event that the first LAN port of the network module is off. Acknowledgement will clear the d-out alarm before you can actually fix the problem. |
| 1.3.6.1.4.1.8691.2.8.1.6.6.5 | ScalarrelayOutputEthernet3LinkDown | read-only | current | The relay dout status of the event that the second LAN port of the network module is off. |
| 1.3.6.1.4.1.8691.2.8.1.6.6.6 | Scalarethernet3LinkDownAcknowledge | write-only | current | Acknowledge the event that the second LAN port of the network module is off. Acknowledgement will clear the d-out alarm before you can actually fix the problem. |
| 1.3.6.1.4.1.8691.2.8.1.6.6.7 | TableportDCDChangedStatusTable | not-accessible | current | DCD changed table. |
| 1.3.6.1.4.1.8691.2.8.1.6.6.7.1 | RowportDCDChangedStatusEntry | not-accessible | current | DCD changed entry. |
| 1.3.6.1.4.1.8691.2.8.1.6.6.7.1.1 | ColumnportDCDChangedStatus | read-only | current | The relay dout status of the event that the DCD signal of the port is changed. |
| 1.3.6.1.4.1.8691.2.8.1.6.6.7.1.2 | ColumnportDCDChangedAcknowledge | write-only | current | Acknowledge the event that the DCD signal of the port is changed. Acknowledgement will clear the d-out alarm before you can actually fix the problem. |
| 1.3.6.1.4.1.8691.2.8.1.6.6.8 | TableportDSRChangedStatusTable | not-accessible | current | DSR changed Table. |
| 1.3.6.1.4.1.8691.2.8.1.6.6.8.1 | RowportDSRChangedStatusEntry | not-accessible | current | DSR changed entry. |
| 1.3.6.1.4.1.8691.2.8.1.6.6.8.1.1 | ColumnportDSRChangedStatus | read-only | current | The relay dout status of the event that the DSR signal of the port is changed. |
| 1.3.6.1.4.1.8691.2.8.1.6.6.8.1.2 | ColumnportDSRChangedAcknowledge | write-only | current | Acknowledge the event that the DSR signal of the port is changed. Acknowledgement will clear the d-out alarm before you can actually fix the problem. |
| 1.3.6.1.4.1.8691.2.8.1.6.7 | NodemoduleStatus | |||
| 1.3.6.1.4.1.8691.2.8.1.6.7.1 | NoderedundancyStatus | |||
| 1.3.6.1.4.1.8691.2.8.1.6.7.1.1 | ScalaractiveRedundancyProtocol | read-only | current | This shows the active redundancy protocol. The none(0) stauts will be showed if only if the redundancy protocol is set to spanning tree and none of ports enabl… |
| 1.3.6.1.4.1.8691.2.8.1.6.7.1.2 | NodespanningTreeStatus | |||
| 1.3.6.1.4.1.8691.2.8.1.6.7.1.2.1 | ScalarspanningTreeBridgeRole | read-only | current | This displays NPort's bridge role (root/not-root) in spanning tree. |
| 1.3.6.1.4.1.8691.2.8.1.6.7.1.2.2 | ScalarspanningTreeRootBridge | read-only | current | This displays root bridge identifier of spanning tree. |
| 1.3.6.1.4.1.8691.2.8.1.6.7.1.2.3 | ScalarspanningTreeRootPathCost | read-only | current | The root path cost of NPort. |
| 1.3.6.1.4.1.8691.2.8.1.6.7.1.2.4 | TablespanningTreePortStatusTable | not-accessible | current | The spanning tree port status table. |
| 1.3.6.1.4.1.8691.2.8.1.6.7.1.2.4.1 | RowspanningTreePortStatusEntry | not-accessible | current | The spanning tree port entry. |
| 1.3.6.1.4.1.8691.2.8.1.6.7.1.2.4.1.1 | ColumnspanningTreePortStatusIndex | read-only | current | The index of spanning tree table. |
| 1.3.6.1.4.1.8691.2.8.1.6.7.1.2.4.1.2 | ColumnspanningTreePortEnableStatus | read-only | current | This displays whether or not spanning tree protocol is enabled for this port. |
| 1.3.6.1.4.1.8691.2.8.1.6.7.1.2.4.1.3 | ColumnspanningTreePortRole | read-only | current | This port's role in spanning tree protocol. |
| 1.3.6.1.4.1.8691.2.8.1.6.7.1.2.4.1.4 | ColumnspanningTreePortDesignatedBridge | read-only | current | This port's designated bridge ID. |
| 1.3.6.1.4.1.8691.2.8.1.6.7.1.2.4.1.5 | ColumnspanningTreePortStatus | read-only | current | The port status of spanning tree protocol. |
| 1.3.6.1.4.1.8691.2.8.1.6.7.1.3 | NodeturboRingStatus | |||
| 1.3.6.1.4.1.8691.2.8.1.6.7.1.3.1 | ScalarturboRingBrokenStatus | read-only | current | Turbo Ring V2 status. |
| 1.3.6.1.4.1.8691.2.8.1.6.7.1.3.2 | ScalarturboRingMaster | read-only | current | Is this a Master or Slave of Turbo Ring or Turbo Ring V2. |
| 1.3.6.1.4.1.8691.2.8.1.6.7.1.3.3 | ScalarturboRingPort1 | read-only | current | The port number of 1st Redundant Port on the Turbo Ring or Turbo Ring V2. Return 0 if not Turbo Ring or Turbo Ring V2. |
| 1.3.6.1.4.1.8691.2.8.1.6.7.1.3.4 | ScalarturboRingPort2 | read-only | current | The port number of 2nd Redundant Port on the Turbo Ring or Turbo Ring V2. Return 0 if not Turbo Ring or Turbo Ring V2. |
| 1.3.6.1.4.1.8691.2.8.1.6.7.1.3.5 | ScalarturboRingPort1Status | read-only | current | The port status of 1st Redundant Port on the Turbo Ring or Turbo Ring V2. |
| 1.3.6.1.4.1.8691.2.8.1.6.7.1.3.6 | ScalarturboRingPort2Status | read-only | current | The port status of 2nd Redundant Port on the Turbo Ring or Turbo Ring V2. |
| 1.3.6.1.4.1.8691.2.8.1.7 | NodesaveConfiguration | |||
| 1.3.6.1.4.1.8691.2.8.1.7.1 | ScalarsaveConfig | write-only | current | Save the applied configuration to the NPort 6000 series device server. |
| 1.3.6.1.4.1.8691.2.8.1.8 | Noderestart | |||
| 1.3.6.1.4.1.8691.2.8.1.8.1 | ScalarrestartPorts | write-only | current | Restart serial port. Restarting will cause port reseting. |
| 1.3.6.1.4.1.8691.2.8.1.8.2 | ScalarrestartSystem | write-only | current | Restart the NPort 6000 series device server. Be sure to save all of your configuration changes before you restart the system. Otherwise, all of the changes wil… |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| PortList | OCTET STRING | current | Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents… |