MOXA-W2x50A-MIB
347 objects
The MIB module for Moxa NPort W2x50A series specific information.
Imported Objects
| SNMPv2-SMI | enterprises IpAddress MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | DateAndTime DisplayString MacAddress TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.8691 | Nodemoxa | |||
| 1.3.6.1.4.1.8691.2 | Nodenport | |||
| 1.3.6.1.4.1.8691.2.13 | Identityw2x50A | The MIB module for Moxa NPort W2x50A series specific information. | ||
| 1.3.6.1.4.1.8691.2.13.1 | NodeswMgmt | |||
| 1.3.6.1.4.1.8691.2.13.1.1 | Nodeoverview | |||
| 1.3.6.1.4.1.8691.2.13.1.1.1 | ScalarmodelName | read-only | current | The model name of the NPort. The possible values of this parameter are: 'NPort W2x50A' for NPort W2x50A. |
| 1.3.6.1.4.1.8691.2.13.1.1.2 | ScalarserialNumber | read-only | current | The serial number of the NPort. Every NPort W2x50A series device server is assigned a unique serial number before it is shipped. |
| 1.3.6.1.4.1.8691.2.13.1.1.3 | ScalarfirmwareVersion | read-only | current | The version of the firmware currently running on the NPort. |
| 1.3.6.1.4.1.8691.2.13.1.1.4 | ScalarethIPAddress | read-only | current | The IP address of the NPort's Ethernet interface. |
| 1.3.6.1.4.1.8691.2.13.1.1.5 | ScalarethMacAddress | read-only | current | The MAC address of the NPort's Ethernet interface. |
| 1.3.6.1.4.1.8691.2.13.1.1.6 | ScalarwlanIPAddress | read-only | current | The IP address of the NPort's WLAN interface. |
| 1.3.6.1.4.1.8691.2.13.1.1.7 | ScalarwlanMacAddress | read-only | current | The MAC address of the NPort's WLAN interface. |
| 1.3.6.1.4.1.8691.2.13.1.1.8 | ScalarwlanSSID | read-only | current | The SSID of WLAN. |
| 1.3.6.1.4.1.8691.2.13.1.1.9 | ScalarwlanNetworkType | read-only | current | Network Type of Wireless LAN. The possible values are 'Infrastrcture Mode' and 'Ad-hoc Mode' |
| 1.3.6.1.4.1.8691.2.13.1.1.10 | ScalarwlanSecurityMode | read-only | current | Security mode of Wireless LAN. The possible values are 'Open System', 'Shared Key', 'WPA', 'WPA-PSK', 'WPA2', 'WPA2-PSK' |
| 1.3.6.1.4.1.8691.2.13.1.1.11 | ScalarwlanRFType | read-only | current | RF type of Wireless LAN. The possible values are 'Auto', '802.11b', '802.11g' |
| 1.3.6.1.4.1.8691.2.13.1.1.12 | ScalarwlanCountryCode | read-only | current | WLAN country code |
| 1.3.6.1.4.1.8691.2.13.1.1.13 | ScalarwlanFastRoaming | read-only | current | Fast roaming state |
| 1.3.6.1.4.1.8691.2.13.1.1.14 | ScalaractiveNetworkPort | read-only | current | Current active network port. The possible values are 'WLAN', 'Ethernet' |
| 1.3.6.1.4.1.8691.2.13.1.1.15 | ScalarupTime | read-only | current | The time (in human-readable notation) since the system was last re-initialized. |
| 1.3.6.1.4.1.8691.2.13.1.1.16 | ScalarserialPort1 | read-only | current | View NPort's serial port 1 setting. |
| 1.3.6.1.4.1.8691.2.13.1.1.17 | ScalarserialPort2 | read-only | current | View NPort's serial port 2 setting. |
| 1.3.6.1.4.1.8691.2.13.1.2 | NodebasicSetting | |||
| 1.3.6.1.4.1.8691.2.13.1.2.1 | NodeserverSetting | |||
| 1.3.6.1.4.1.8691.2.13.1.2.1.1 | ScalarserverName | read-write | current | A text string used to identify the NPort. |
| 1.3.6.1.4.1.8691.2.13.1.2.1.2 | ScalarserverLocation | read-write | current | A text string used to identify the location of the NPort. This option is useful for specifying the location or application of different NPort device servers. |
| 1.3.6.1.4.1.8691.2.13.1.2.2 | NodetimeSetting | |||
| 1.3.6.1.4.1.8691.2.13.1.2.2.1 | ScalartimeZone | read-write | current | The time-zone index of the NPort. |
| 1.3.6.1.4.1.8691.2.13.1.2.2.2 | ScalarlocalTime | read-write | current | The system time in the following format yyyy/mm/dd hh:mm:ss |
| 1.3.6.1.4.1.8691.2.13.1.2.2.3 | ScalartimeServer | read-write | current | The NPort W2x50A series device server uses SNTP (RFC-1769) for auto time calibration. Input the correct 'Time server' IP address or domain name. Once the NPort… |
| 1.3.6.1.4.1.8691.2.13.1.3 | NodenetworkSetting | |||
| 1.3.6.1.4.1.8691.2.13.1.3.1 | NodegeneralSetting | |||
| 1.3.6.1.4.1.8691.2.13.1.3.1.1 | ScalardnsServer1IpAddr | read-write | current | The first DNS server address. When the user wants to visit a particular website, the computer asks a Domain Name System (DNS) server for the website's correct … |
| 1.3.6.1.4.1.8691.2.13.1.3.1.2 | ScalardnsServer2IpAddr | read-write | current | The second DNS server address. When the user wants to visit a particular website, the computer asks a Domain Name System (DNS) server for the website's correct… |
| 1.3.6.1.4.1.8691.2.13.1.3.2 | NodeethernetSetting | |||
| 1.3.6.1.4.1.8691.2.13.1.3.2.1 | ScalarethIpConfiguration | read-write | current | The IP configuration mode of the NPort. You can choose from four possible IP configuration modes: Static, DHCP, DHCP/BOOTP, BOOTP. |
| 1.3.6.1.4.1.8691.2.13.1.3.2.2 | ScalarethIpAddress | read-write | current | An IP address is a number assigned to a network device (such as a computer) as a permanent address on the network. Computers use the IP address to identify and… |
| 1.3.6.1.4.1.8691.2.13.1.3.2.3 | ScalarethNetMask | read-write | current | A subnet mask represents all of the network hosts at one geographic location, in one building, or on the same local area network. When a packet is sent out ove… |
| 1.3.6.1.4.1.8691.2.13.1.3.2.4 | ScalarethDefaultGateway | read-write | current | A gateway is a network computer that acts as an entrance to another network. Usually, the computers that control traffic within the network or at the local Int… |
| 1.3.6.1.4.1.8691.2.13.1.3.2.5 | ScalarethBridgeMode | read-write | current | Enable or disable the bridge function. |
| 1.3.6.1.4.1.8691.2.13.1.3.3 | NodewlanSetting | |||
| 1.3.6.1.4.1.8691.2.13.1.3.3.1 | ScalarwlanIpConfiguration | read-write | current | The IP configuration mode of the NPort. You can choose from four possible IP configuration modes: Static, DHCP, DHCP/BOOTP, BOOTP. |
| 1.3.6.1.4.1.8691.2.13.1.3.3.2 | ScalarwlanIpAddress | read-write | current | An IP address is a number assigned to a network device (such as a computer) as a permanent address on the network. Computers use the IP address to identify and… |
| 1.3.6.1.4.1.8691.2.13.1.3.3.3 | ScalarwlanNetMask | read-write | current | A subnet mask represents all of the network hosts at one geographic location, in one building, or on the same local area network. When a packet is sent out ove… |
| 1.3.6.1.4.1.8691.2.13.1.3.3.4 | ScalarwlanDefaultGateway | read-write | current | A gateway is a network computer that acts as an entrance to another network. Usually, the computers that control traffic within the network or at the local Int… |
| 1.3.6.1.4.1.8691.2.13.1.3.4 | NodeprofileSetting | |||
| 1.3.6.1.4.1.8691.2.13.1.3.4.1 | ScalarnetworkType | read-write | current | Select WLAN network type. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.2 | NodeadhocProfile | |||
| 1.3.6.1.4.1.8691.2.13.1.3.4.2.1 | NodeadhocGeneralSetting | |||
| 1.3.6.1.4.1.8691.2.13.1.3.4.2.1.1 | ScalaradhocProfileName | read-write | current | Assign profile name. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.2.1.2 | ScalaradhocRFType | read-write | current | Select WLAN network type. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.2.1.3 | ScalaradhocWlanSSID | read-write | current | Set WLAN SSID |
| 1.3.6.1.4.1.8691.2.13.1.3.4.2.1.4 | ScalaradhocChannel | read-write | current | Display currently used channel. When in Ad-Hoc mode, this value can be set. mode region possible channel ====================================== 802.11b_g : 1, … |
| 1.3.6.1.4.1.8691.2.13.1.3.4.2.2 | NodeadhocSecuritySetting | |||
| 1.3.6.1.4.1.8691.2.13.1.3.4.2.2.1 | ScalaradhocAuthentication | read-only | current | Wireless LAN autentication type. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.2.2.2 | ScalaradhocEncryption | read-write | current | Set encryption type. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.2.2.3 | ScalaradhocWepKeyLength | read-write | current | WEP key length. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.2.2.4 | ScalaradhocWepKeyIndex | read-write | current | WEP key index 1~4. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.2.2.5 | ScalaradhocWepKeyPassphrase | write-only | current | WEP key passphrase. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.2.2.6 | ScalaradhocWepKeyFormat | read-write | current | WEP key format. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3 | NodeinfrastructureProfile | |||
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.1 | NodeinfraGeneralSetting | |||
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1 | TableinfraGeneralSettingTable | not-accessible | current | WLAN profile general setting table. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1.1 | RowinfraGeneralSettingEntry | not-accessible | current | WLAN profile general setting entry. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1.1.1 | ColumnprofileIndex | read-only | current | The profile index |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1.1.2 | ColumnprofileName | read-write | current | Assign profile name. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1.1.3 | ColumnprofileRFType | read-write | current | Select WLAN network type. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1.1.4 | ColumnprofileWlanSSID | read-write | current | Set WLAN SSID |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.2 | NodesecuritySetting | |||
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1 | TablesecuritySettingTable | not-accessible | current | WLAN profile security setting table. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1 | RowsecuritySettingEntry | not-accessible | current | WLAN profile security setting entry. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.1 | Columnauthentication | read-write | current | Wireless LAN autentication type. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.2 | Columnencryption | read-write | current | Set encryption type. Selection rule is as following. authentication selectable encryption ============== ===================== open-system(0) disable(0), wep(1… |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.3 | ColumnwepKeyLength | read-write | current | WEP key length. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.4 | ColumnwepKeyIndex | read-write | current | WEP key index 1~4. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.5 | ColumnwepKeyPassphrase | write-only | current | WEP key passphrase. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.6 | ColumnwepKeyFormat | read-write | current | WEP key format. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.12 | ColumneapMethod | read-write | current | EAP method for WPA and WPA2 authentication. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.13 | ColumntunneledAuth | read-write | current | Set tunneled authentication protocol when PEAP/TTLS is selected as EAP method. EAP method selectable tunneled authentication ========== =======================… |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.14 | ColumnwpaUsername | read-write | current | WPA username for WPA and WPA2 authentication. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.16 | ColumnwpaAnonymousUsername | read-write | current | Anonymous username needed when TTLS is selected as EAP method. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.17 | ColumnverifyServerCert | read-write | current | The setting of verify server certificate. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.18 | ColumntrustedServerCert | read-only | current | Display whether or not trusted server certificate is installed. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.19 | ColumnuserCert | read-only | current | Display whether or not user certificate is installed. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.20 | ColumnuserPrivateKey | read-only | current | Display whether or not user private key is installed. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.3 | ScalarfastRoamingSetting | read-write | current | The setting of fast roaming. |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.4 | ScalarfastRoamingScanChannels1 | read-write | current | The scan channels of fast roaming. 0 represents 'N/A' ====================================================== Auot channel : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, … |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.5 | ScalarfastRoamingScanChannels2 | read-write | current | The scan channels of fast roaming. 0 represents 'N/A' ====================================================== Auot channel : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, … |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.6 | ScalarfastRoamingScanChannels3 | read-write | current | The scan channels of fast roaming. 0 represents 'N/A' ====================================================== Auot channel : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, … |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.7 | ScalarfastRoamingThreshold | read-write | current | Roaming threshold of fast roaming |
| 1.3.6.1.4.1.8691.2.13.1.3.4.3.8 | ScalarfastRoamingDifference | read-write | current | Roaming difference of fast roaming |
| 1.3.6.1.4.1.8691.2.13.1.3.5 | NodewlanLogSetting | |||
| 1.3.6.1.4.1.8691.2.13.1.3.5.1 | ScalarwlanLogEnable | read-write | current | Enable or disable WLAN log |
| 1.3.6.1.4.1.8691.2.13.1.3.6 | NodeadvancedSetting | |||
| 1.3.6.1.4.1.8691.2.13.1.3.6.1 | ScalargratuitousArp | read-write | current | Enable or disable the gratuitous ARP function. For some applications, users need the NPort W2x50A series device server to send broadcast packets to update the … |
| 1.3.6.1.4.1.8691.2.13.1.3.6.2 | ScalargratuitousArpSendPeriod | read-write | current | The send period of the gratuitous ARP function. Range: 10 ~ 1000 sec. |
| 1.3.6.1.4.1.8691.2.13.1.3.6.3 | ScalargratuitousArpIpAddress1 | read-write | current | The IP address of the static gratuitous ARP. |
| 1.3.6.1.4.1.8691.2.13.1.3.6.4 | ScalargratuitousArpMacAddress1 | read-write | current | The MAC address of the static gratuitous ARP. |
| 1.3.6.1.4.1.8691.2.13.1.3.6.5 | ScalargratuitousArpIpAddress2 | read-write | current | The IP address of the static gratuitous ARP. |
| 1.3.6.1.4.1.8691.2.13.1.3.6.6 | ScalargratuitousArpMacAddress2 | read-write | current | The MAC address of the static gratuitous ARP. |
| 1.3.6.1.4.1.8691.2.13.1.3.6.7 | ScalargratuitousArpIpAddress3 | read-write | current | The IP address of the static gratuitous ARP. |
| 1.3.6.1.4.1.8691.2.13.1.3.6.8 | ScalargratuitousArpMacAddress3 | read-write | current | The MAC address of the static gratuitous ARP. |
| 1.3.6.1.4.1.8691.2.13.1.3.6.9 | ScalargratuitousArpIpAddress4 | read-write | current | The IP address of the static gratuitous ARP. |
| 1.3.6.1.4.1.8691.2.13.1.3.6.10 | ScalargratuitousArpMacAddress4 | read-write | current | The MAC address of the static gratuitous ARP. |
| 1.3.6.1.4.1.8691.2.13.1.4 | NodeportSetting | |||
| 1.3.6.1.4.1.8691.2.13.1.4.1 | NodeopModeSetting | |||
| 1.3.6.1.4.1.8691.2.13.1.4.1.1 | NodeopMode | |||
| 1.3.6.1.4.1.8691.2.13.1.4.1.1.1 | TableopModePortTable | not-accessible | current | The serial ports' operation mode table. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.1.1.1 | RowopModePortEntry | not-accessible | current | The serial port's operation mode entry. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.1.1.1.1 | ColumnportIndex | read-only | current | The serial port index. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.1.1.1.2 | ColumnportMode | read-write | current | The operation mode of the serial port. Note that changing this setting may also change the application. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2 | NodeopModeParam | |||
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.1 | NoderealCOM | |||
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1 | TablerealCOMTable | not-accessible | current | The Real COM mode table. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1 | RowrealCOMEntry | not-accessible | current | The Real COM mode entry. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.1 | ColumnrealCOMTcpAliveCheck | read-write | current | The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device server automati… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.2 | ColumnrealCOMMaxConnection | read-write | current | Max connection is usually used when the user needs to receive data from different hosts simultaneously. The factory default is 1. In this case, only one specif… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.3 | ColumnrealCOMIgnoreJammedIp | read-write | current | Previously, when Max connection was set to a value greater than 1, and the serial device was transmitting data, if any one of the connected hosts stopped respo… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.4 | ColumnrealCOMAllowDriverControl | read-write | current | If Max connection is greater than 1, NPort will ignore driver control commands from all connected hosts. However, if you set Allow driver control to YES, contr… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.5 | ColumnrealCOMConnectionDownRTS | read-write | current | For some applications, serial devices must obtain the Ethernet link status by reading the RTS signal from the NPort W2x50A series device server. If this settin… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.6 | ColumnrealCOMConnectionDownDTR | read-write | current | For some applications, serial devices must obtain the Ethernet link status by reading the DTR signal from the NPort W2x50A series device server. If this settin… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.2 | Noderfc2217 | |||
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.2.1 | Tablerfc2217Table | not-accessible | current | The RFC2217 mode table. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.2.1.1 | Rowrfc2217Entry | not-accessible | current | The RFC2217 mode entry. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.2.1.1.1 | Columnrfc2217TcpAliveCheck | read-write | current | The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device server automati… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.2.1.1.2 | Columnrfc2217TcpPort | read-write | current | TCP server port of RFC2217. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.3 | NodetcpServer | |||
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1 | TabletcpServerTable | not-accessible | current | The TCP server mode table. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1 | RowtcpServerEntry | not-accessible | current | The TCP server mode entry. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.1 | ColumntcpServerTcpAliveCheck | read-write | current | The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device server automati… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.2 | ColumntcpServerInactivityTime | read-write | current | 0 ms: TCP connection is not closed when the serial line is idle. 1-65535 ms: The NPort W2x50A series device server automatically closes the TCP connection if t… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.3 | ColumntcpServerMaxConnection | read-write | current | Max connection is usually used when the user needs to receive data from different hosts simultaneously. The factory default is 1. In this case, only one specif… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.4 | ColumntcpServerIgnoreJammedIp | read-write | current | Previously, when Max connection was set to a value greater than 1, and the serial device was transmitting data, if any one of the connected hosts stopped respo… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.5 | ColumntcpServerAllowDriverControl | read-write | current | If Max connection is greater than 1, NPort will ignore driver control commands from all connected hosts. However, if you set Allow driver control to YES, contr… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.6 | ColumntcpServerTcpPort | read-write | current | The 'TCP port' is the TCP port that the NPort W2x50A series device server uses to listen to connections, and that other devices must use to contact the NPort W… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.7 | ColumntcpServerCmdPort | read-write | current | The 'Command port' is a TCP port used to listen for SSDK commands from the host. In order to prevent a TCP port conflict with other applications, the user can … |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.8 | ColumntcpServerConnectionDownRTS | read-write | current | For some applications, serial devices must obtain the Ethernet link status from the RTS signal sent by the NPort W2x50A series device server. If this setting i… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.9 | ColumntcpServerConnectionDownDTR | read-write | current | For some applications, serial devices must obtain the Ethernet link status from the DTR signal sent by the NPort W2x50A series device server. If this setting i… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.4 | NodetcpClient | |||
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1 | TabletcpClientTable | not-accessible | current | The TCP client mode table. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1 | RowtcpClientEntry | not-accessible | current | The TCP client mode entry. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.1 | ColumntcpClientTcpAliveCheck | read-write | current | The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device client automati… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.2 | ColumntcpClientInactivityTime | read-write | current | 0 ms: TCP connection is not closed when the serial line is idle. 1-65535 ms: The NPort W2x50A series device client automatically closes the TCP connection if t… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.3 | ColumntcpClientIgnoreJammedIp | read-write | current | Previously, when Max connection was set to a value greater than 1, and the serial device was transmitting data, if any one of the connected hosts stopped respo… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.4 | ColumntcpClientDestinationAddress1 | read-write | current | The NPort W2x50A series device server can connect actively to a remote host that has this IP address. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.5 | ColumntcpClientDestinationPort1 | read-write | current | The NPort W2x50A series device server can connect actively to a remote host that has this TCP port number. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.6 | ColumntcpClientDestinationAddress2 | read-write | current | The NPort W2x50A series device server can connect actively to a remote host that has this IP address. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.7 | ColumntcpClientDestinationPort2 | read-write | current | The NPort W2x50A series device server can connect actively to a remote host that has this TCP port number. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.8 | ColumntcpClientDestinationAddress3 | read-write | current | The NPort W2x50A series device server can connect actively to a remote host that has this IP address. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.9 | ColumntcpClientDestinationPort3 | read-write | current | The NPort W2x50A series device server can connect actively to a remote host that has this port number. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.10 | ColumntcpClientDestinationAddress4 | read-write | current | The NPort W2x50A series device server can connect actively to a remote host that has this IP address. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.11 | ColumntcpClientDestinationPort4 | read-write | current | The NPort W2x50A series device server can connect actively to a remote host that has this port number. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.12 | ColumntcpClientDesignatedLocalPort1 | read-write | current | The local TCP port used to connect actively to the remote host. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.13 | ColumntcpClientDesignatedLocalPort2 | read-write | current | The local TCP port used to connect actively to the remote host. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.14 | ColumntcpClientDesignatedLocalPort3 | read-write | current | The local TCP port used to connect actively to the remote host. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.15 | ColumntcpClientDesignatedLocalPort4 | read-write | current | The local TCP port used to connect actively to the remote host. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.16 | ColumntcpClientConnectionControl | read-write | current | Events that cause the TCP client to drop the connection. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.5 | Nodeudp | |||
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1 | TableudpTable | not-accessible | current | The UDP mode table. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1 | RowudpEntry | not-accessible | current | The UDP mode entry. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.1 | ColumnudpDestinationAddress1Begin | read-write | current | The NPort W2x50A series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and udpDestinati… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.2 | ColumnudpDestinationAddress1End | read-write | current | The NPort W2x50A series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between udpDestinationAddress1Begin and… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.3 | ColumnudpDestinationPort1 | read-write | current | The NPort W2x50A series device server can actively send UDP packets to remote hosts that have this UDP port number. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.4 | ColumnudpDestinationAddress2Begin | read-write | current | The NPort W2x50A series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and udpDestinati… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.5 | ColumnudpDestinationAddress2End | read-write | current | The NPort W2x50A series device server can actively send UDP packets to the remote hosts whose IP addresses are in the range between udpDestinationAddress2Begin… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.6 | ColumnudpDestinationPort2 | read-write | current | The NPort W2x50A series device server can actively send UDP packets to the remote hosts that have this UDP port number. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.7 | ColumnudpDestinationAddress3Begin | read-write | current | The NPort W2x50A series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and udpDestinati… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.8 | ColumnudpDestinationAddress3End | read-write | current | The NPort W2x50A series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between udpDestinationAddress3Begin and… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.9 | ColumnudpDestinationPort3 | read-write | current | The NPort W2x50A series device server can actively send UDP packets to remote hosts that have this UDP port number. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.10 | ColumnudpDestinationAddress4Begin | read-write | current | The NPort W2x50A series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and udpDestinati… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.11 | ColumnudpDestinationAddress4End | read-write | current | The NPort W2x50A series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between udpDestinationAddress4Begin and… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.12 | ColumnudpDestinationPort4 | read-write | current | The NPort W2x50A series device server can actively send UDP packets to remote hosts that have this UDP port number. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.13 | ColumnudpLocalListenPort | read-write | current | The UDP port that the NPort W2x50A series device server listens to and that other devices must use to contact the NPort W2x50A series device server. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.6 | NodepairConnectionMaster | |||
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.6.1 | TablepairConnectionMasterTable | not-accessible | current | The pair connection master mode table. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.6.1.1 | RowpairConnectionMasterEntry | not-accessible | current | The pair connection master mode entry. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.6.1.1.1 | ColumnpairConnectionMasterTcpAliveCheck | read-write | current | The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device server automati… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.6.1.1.2 | ColumnpairConnectionMasterDestnationAddress | read-write | current | IP address of pair connection slave. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.6.1.1.3 | ColumnpairConnectionMasterDestnationTcpPort | read-write | current | TCP port of pair connection slave. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.7 | NodepairConnectionSlave | |||
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.7.1 | TablepairConnectionSlaveTable | not-accessible | current | The pair connection slave mode table. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.7.1.1 | RowpairConnectionSlaveEntry | not-accessible | current | The pair connection slave mode entry. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.7.1.1.1 | ColumnpairConnectionSlaveTcpAliveCheck | read-write | current | The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device server automati… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.7.1.1.2 | ColumnpairConnectionSlaveLocalTcpPort | read-write | current | TCP server port of pair connection slave. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.8 | NodeethernetModem | |||
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.8.1 | TableethernetModemTable | not-accessible | current | The ethernet modem mode table. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.8.1.1 | RowethernetModemEntry | not-accessible | current | The ethernet modem mode entry. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.8.1.1.1 | ColumnethernetModemTcpAliveCheck | read-write | current | The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device server automati… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.8.1.1.2 | ColumnethernetModemLocalTcpPort | read-write | current | TCP server port of ethernet modem. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.9 | NodereverseTerminal | |||
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1 | TablereverseTerminalTable | not-accessible | current | The reverse terminal mode table. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1 | RowreverseTerminalEntry | not-accessible | current | The reverse terminal mode entry. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1.1 | ColumnreverseTerminalTcpAliveCheck | read-write | current | The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device server automati… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1.2 | ColumnreverseTerminalInactivityTime | read-write | current | 0 min: TCP connection is not closed when the serial line is idle. 0-99 min: The NPort W2x50A series device server automatically closes the TCP connection if th… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1.3 | ColumnreverseTerminalTcpPort | read-write | current | Each of the NPort W2x50A series device server's serial ports are mapped to a TCP port. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1.4 | ColumnreverseTerminalAuthenticationType | read-write | current | The reverse terminal authentication type. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1.5 | ColumnreverseTerminalMapKeys | read-write | current | If data received through NPort W2x50A series device server's Ethernet port is sent using the 'enter' command, the data will be transmitted out through the seri… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.3 | NodedataPacking | |||
| 1.3.6.1.4.1.8691.2.13.1.4.1.3.1 | TabledataPackingPortTable | not-accessible | current | The Data Packing table. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1 | RowdataPackingPortEntry | not-accessible | current | The Data Packing entry. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.1 | ColumnportPacketLength | read-write | current | If the value is 0, the Delimiter Process will be used, regardless of the length of the data packet. If the data length (in bytes) matches the configured value,… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.2 | ColumnportDelimiter1Enable | read-write | current | Enable the first delimiter character. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.3 | ColumnportDelimiter1 | read-write | current | The first delimiter character, in hex decimal. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.4 | ColumnportDelimiter2Enable | read-write | current | Enable the second delimiter character. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.5 | ColumnportDelimiter2 | read-write | current | The second delimiter character, in hex decimal. |
| 1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.6 | ColumnportDelimiterProcess | read-write | current | 'delimiterAddOne' or 'delimiterAddTwo': The data will be transmitted when an additional byte (for 'delimiterAddOne'), or an additional 2 bytes (for 'delimiterA… |
| 1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.7 | ColumnportForceTransmit | read-write | current | 0: Disable the force transmit timeout. 1 to 65535: Forces the NPort W2x50A series device server's TCP/IP protocol software to try to pack serial data received … |
| 1.3.6.1.4.1.8691.2.13.1.4.2 | NodecomParamSetting | |||
| 1.3.6.1.4.1.8691.2.13.1.4.2.1 | TablecomParamPortTable | not-accessible | current | The Communication Parameters table. |
| 1.3.6.1.4.1.8691.2.13.1.4.2.1.1 | RowcomParamPortEntry | not-accessible | current | The Communication Parameters entry. |
| 1.3.6.1.4.1.8691.2.13.1.4.2.1.1.1 | ColumnportAlias | read-write | current | Port alias is included to allow easy identification of the serial devices that are connected to NPort W2x50A series device server's serial port. |
| 1.3.6.1.4.1.8691.2.13.1.4.2.1.1.2 | ColumnportInterface | read-write | current | The serial interface that the port works on. |
| 1.3.6.1.4.1.8691.2.13.1.4.2.1.1.3 | ColumnportBaudRate | read-write | current | The port's speed in bits per second. You can choose a standard baud rate by indexing. |
| 1.3.6.1.4.1.8691.2.13.1.4.2.1.1.4 | ColumnportDataBits | read-write | current | The number of bits in a character for the port. |
| 1.3.6.1.4.1.8691.2.13.1.4.2.1.1.5 | ColumnportStopBits | read-write | current | The number of stop bits for the port. |
| 1.3.6.1.4.1.8691.2.13.1.4.2.1.1.6 | ColumnportParity | read-write | current | The parity bit for the port. |
| 1.3.6.1.4.1.8691.2.13.1.4.2.1.1.7 | ColumnportFlowControl | read-write | current | The flow-control method for the port. |
| 1.3.6.1.4.1.8691.2.13.1.4.2.1.1.8 | ColumnportFIFO | read-write | current | Enable or disable the port's FIFO. |
| 1.3.6.1.4.1.8691.2.13.1.4.3 | NodedataBuffering | |||
| 1.3.6.1.4.1.8691.2.13.1.4.3.1 | TabledataBufferingPortTable | not-accessible | current | The Data Buffering table. |
| 1.3.6.1.4.1.8691.2.13.1.4.3.1.1 | RowdataBufferingPortEntry | not-accessible | current | The Data Buffering entry. |
| 1.3.6.1.4.1.8691.2.13.1.4.3.1.1.1 | ColumnportBufferingEnable | read-write | current | Enable off-line port buffering. |
| 1.3.6.1.4.1.8691.2.13.1.4.3.1.1.2 | ColumnportSerialDataLoggingEnable | read-write | current | Enable or disable serial data logging for the port. |
| 1.3.6.1.4.1.8691.2.13.1.5 | NodesysManagement | |||
| 1.3.6.1.4.1.8691.2.13.1.5.1 | NodemiscNetworkSettings | |||
| 1.3.6.1.4.1.8691.2.13.1.5.1.1 | NodeaccessibleIp | |||
| 1.3.6.1.4.1.8691.2.13.1.5.1.1.1 | ScalarenableAccessibleIpList | read-write | current | Enable or disable the entire accessible IP list. |
| 1.3.6.1.4.1.8691.2.13.1.5.1.1.2 | TableaccessibleIpListTable | not-accessible | current | Accessible IP List table. |
| 1.3.6.1.4.1.8691.2.13.1.5.1.1.2.1 | RowaccessibleIpListEntry | not-accessible | current | Accessible IP List entry. |
| 1.3.6.1.4.1.8691.2.13.1.5.1.1.2.1.1 | ColumnaccessibleIpListIndex | read-only | current | Accessible IP List index. |
| 1.3.6.1.4.1.8691.2.13.1.5.1.1.2.1.2 | ColumnactiveAccessibleIpList | read-write | current | Enable or disable this accessible IP entry. |
| 1.3.6.1.4.1.8691.2.13.1.5.1.1.2.1.3 | ColumnaccessibleIpListAddress | read-write | current | Accessible IP address. This value can be the IP address of a single host if the netmask is set to '255.255.255.255,' or it can be a network address. |
| 1.3.6.1.4.1.8691.2.13.1.5.1.1.2.1.4 | ColumnaccessibleIpListNetmask | read-write | current | Accessible IP address netmask. The IP address and netmask are used to specify a group of remote hosts. |
| 1.3.6.1.4.1.8691.2.13.1.5.1.2 | NodesnmpAgentSettings | |||
| 1.3.6.1.4.1.8691.2.13.1.5.1.2.1 | ScalarsnmpEnable | read-write | current | Enable or disable SNMP agent. |
| 1.3.6.1.4.1.8691.2.13.1.5.1.2.2 | ScalarsnmpContactName | read-write | current | The SNMP contact information usually includes an emergency contact name and telephone or pager number. |
| 1.3.6.1.4.1.8691.2.13.1.5.1.2.3 | ScalarsnmpLocation | read-write | current | Specify the location string for SNMP agents, such as the NPort W2x50A series device server. This string is usually set to the street address where the NPort W2… |
| 1.3.6.1.4.1.8691.2.13.1.5.1.4 | NodeauthenticationServer | |||
| 1.3.6.1.4.1.8691.2.13.1.5.1.4.1 | ScalarradiusServerIp | read-write | current | The IP address or domain name of the RADIUS server. |
| 1.3.6.1.4.1.8691.2.13.1.5.1.4.3 | ScalarudpPortAuthenticationServer | read-write | current | The UDP port of the RADIUS server. |
| 1.3.6.1.4.1.8691.2.13.1.5.1.4.4 | ScalarradiusAccounting | read-write | current | Enable or disable RADIUS accounting. |
| 1.3.6.1.4.1.8691.2.13.1.5.1.5 | NodesysLogSettings | |||
| 1.3.6.1.4.1.8691.2.13.1.5.1.5.1 | ScalarsysLocalLog | read-write | current | System cold start, System warm start. |
| 1.3.6.1.4.1.8691.2.13.1.5.1.5.2 | ScalarnetworkLocalLog | read-write | current | DHCP/BOOTP get IP/renew, mail fail, NTP connect fail, IP conflict, network link down. |
| 1.3.6.1.4.1.8691.2.13.1.5.1.5.3 | ScalarconfigLocalLog | read-write | current | Login fail, IP changed, password changed, firmware upgrade, SSL certificate import, config export, wireless certificate import, serial data log export. |
| 1.3.6.1.4.1.8691.2.13.1.5.1.5.4 | ScalaropModeLocalLog | read-write | current | Connect, Disconnect, Restart. |
| 1.3.6.1.4.1.8691.2.13.1.5.2 | NodeautoWarningSettings | |||
| 1.3.6.1.4.1.8691.2.13.1.5.2.1 | NodeeventSettings | |||
| 1.3.6.1.4.1.8691.2.13.1.5.2.1.1 | ScalarmailWarningColdStart | read-write | current | Refers to starting the system from power off (contrast this with warm start). When performing a cold start, the NPort W2x50A series device server will automati… |
| 1.3.6.1.4.1.8691.2.13.1.5.2.1.2 | ScalarmailWarningWarmStart | read-write | current | Refers to restarting the NPort W2x50A without turning the power off. When performing a warm start, the NPort W2x50A series device server will automatically sen… |
| 1.3.6.1.4.1.8691.2.13.1.5.2.1.3 | ScalarmailWarningAuthFailure | read-write | current | The user inputs a wrong password from the Console or Administrator. When authentication failure occurs, the NPort W2x50A series device server will immediately … |
| 1.3.6.1.4.1.8691.2.13.1.5.2.1.4 | ScalarmailWarningIpChanged | read-write | current | The user has changed the NPort W2x50A series device server's IP address. When the IP address changes,the NPort W2x50A series device server will send an e-mail … |
| 1.3.6.1.4.1.8691.2.13.1.5.2.1.5 | ScalarmailWarningPasswordChanged | read-write | current | The user has changed the NPort W2x50A series device server's password. When the password changes, the NPort W2x50A series device server will send an e-mail wit… |
| 1.3.6.1.4.1.8691.2.13.1.5.2.1.6 | ScalartrapServerColdStart | read-write | current | Refers to starting the system from power off (contrast this with warm start). When performing a cold start, the NPort W2x50A series device server will automati… |
| 1.3.6.1.4.1.8691.2.13.1.5.2.1.7 | ScalartrapServerWarmStart | read-write | current | Refers to restarting the NPort W2x50A without turning the power off. When performing a warm start, the NPort W2x50A series device server will automatically sen… |
| 1.3.6.1.4.1.8691.2.13.1.5.2.1.8 | ScalartrapServerAuthFailure | read-write | current | The user inputs a wrong password from the Console or Administrator. When authentication failure occurs, the NPort W2x50A series device server will immediately … |
| 1.3.6.1.4.1.8691.2.13.1.5.2.2 | NodeserialEventSettings | |||
| 1.3.6.1.4.1.8691.2.13.1.5.2.2.1 | TableportEventSettingsTable | not-accessible | current | Port Event Settings Table. |
| 1.3.6.1.4.1.8691.2.13.1.5.2.2.1.1 | RowportEventSettingsEntry | not-accessible | current | Port Event Settings entry. |
| 1.3.6.1.4.1.8691.2.13.1.5.2.2.1.1.1 | ColumnmailDCDchange | read-write | current | A change in the DCD (Data Carrier Detect) signal indicates that the modem connection status has changed. For example, if the DCD signal changes to low, it indi… |
| 1.3.6.1.4.1.8691.2.13.1.5.2.2.1.1.2 | ColumntrapDCDchange | read-write | current | A change in the DCD (Data Carrier Detect) signal indicates that the modem connection status has changed. For example, if the DCD signal changes to low, it indi… |
| 1.3.6.1.4.1.8691.2.13.1.5.2.2.1.1.3 | ColumnmailDSRchange | read-write | current | A change in the DSR (Data Set Ready) signal indicates that the data communication equipment is powered off. For example, if the DSR signal changes to low, it i… |
| 1.3.6.1.4.1.8691.2.13.1.5.2.2.1.1.4 | ColumntrapDSRchange | read-write | current | A change in the DSR (Data Set Ready) signal indicates that the data communication equipment is powered off. For example, if the DSR signal changes to low, it i… |
| 1.3.6.1.4.1.8691.2.13.1.5.2.3 | NodeemailAlert | |||
| 1.3.6.1.4.1.8691.2.13.1.5.2.3.1 | ScalaremailWarningMailServer | read-write | current | The e-mail server's IP address or domain name of the e-mail warning function. |
| 1.3.6.1.4.1.8691.2.13.1.5.2.3.2 | ScalaremailRequiresAuthentication | read-write | current | Set if the mail server requires user login. |
| 1.3.6.1.4.1.8691.2.13.1.5.2.3.3 | ScalaremailWarningUserName | read-write | current | The user name used to log into the mail server if authentication is required. |
| 1.3.6.1.4.1.8691.2.13.1.5.2.3.5 | ScalaremailWarningFromEmail | read-write | current | The e-mail address to be filled in the 'From' field of the auto-warning e-mail. |
| 1.3.6.1.4.1.8691.2.13.1.5.2.3.6 | ScalaremailWarningFirstEmailAddr | read-write | current | The first email address to where the auto-warning e-mail is to be sent. |
| 1.3.6.1.4.1.8691.2.13.1.5.2.3.7 | ScalaremailWarningSecondEmailAddr | read-write | current | The second email address to where the auto-warning e-mail is to be sent. |
| 1.3.6.1.4.1.8691.2.13.1.5.2.3.8 | ScalaremailWarningThirdEmailAddr | read-write | current | The third email address to where the auto-warning e-mail is to be sent. |
| 1.3.6.1.4.1.8691.2.13.1.5.2.3.9 | ScalaremailWarningFourthEmailAddr | read-write | current | The fourth email address to where the auto-warning e-mail is to be sent. |
| 1.3.6.1.4.1.8691.2.13.1.5.2.4 | NodesnmpTrap | |||
| 1.3.6.1.4.1.8691.2.13.1.5.2.4.1 | ScalarsnmpTrapReceiverIp | read-write | current | SNMP trap server IP address or domain name. |
| 1.3.6.1.4.1.8691.2.13.1.5.2.4.2 | ScalartrapVersion | read-write | current | SNMP trap version used for the auto-warning function. |
| 1.3.6.1.4.1.8691.2.13.1.5.3 | Nodemaintenance | |||
| 1.3.6.1.4.1.8691.2.13.1.5.3.1 | NodeconsoleSettings | |||
| 1.3.6.1.4.1.8691.2.13.1.5.3.1.1 | ScalarhttpConsole | read-write | current | Enable or disable HTTP console. |
| 1.3.6.1.4.1.8691.2.13.1.5.3.1.2 | ScalarhttpsConsole | read-write | current | Enable or disable HTTPS console. |
| 1.3.6.1.4.1.8691.2.13.1.5.3.1.3 | ScalartelnetConsole | read-write | current | Enable or disable Telnet console. |
| 1.3.6.1.4.1.8691.2.13.1.5.3.1.4 | ScalarsshConsole | read-write | current | Enable or disable SSH console. |
| 1.3.6.1.4.1.8691.2.13.1.5.3.1.5 | ScalarserialConsole | read-write | current | Enable or disable Serial console. |
| 1.3.6.1.4.1.8691.2.13.1.5.3.1.6 | ScalarresetButton | read-write | current | Reset button setting. |
| 1.3.6.1.4.1.8691.2.13.1.5.3.2 | NodeloadFactoryDefault | |||
| 1.3.6.1.4.1.8691.2.13.1.5.3.2.1 | ScalarloadFactoryDefaultSetting | write-only | current | This function will reset all of the NPort W2x50A series device server's settings to the factory default values. Be aware that previous settings will be lost. S… |
| 1.3.6.1.4.1.8691.2.13.1.6 | NodesysStatus | |||
| 1.3.6.1.4.1.8691.2.13.1.6.1 | Nodes2eConnections | |||
| 1.3.6.1.4.1.8691.2.13.1.6.1.1 | TablemonitorRemoteIpTable | not-accessible | current | Serial to Network Connections Remote IP table. |
| 1.3.6.1.4.1.8691.2.13.1.6.1.1.1 | RowmonitorRemoteIpEntry | not-accessible | current | Serial to Network Connections Remote IP entry. |
| 1.3.6.1.4.1.8691.2.13.1.6.1.1.1.1 | ColumnremoteIpIndex | read-only | current | Serial to Network Connections Remote IP index. |
| 1.3.6.1.4.1.8691.2.13.1.6.1.1.1.2 | ColumnmonitorRemoteIp | read-only | current | The remote IP currently connecting to this port. |
| 1.3.6.1.4.1.8691.2.13.1.6.2 | NodeserialPortStatus | |||
| 1.3.6.1.4.1.8691.2.13.1.6.2.1 | TablemonitorSerialPortStatusTable | not-accessible | current | Serial Port Status table. |
| 1.3.6.1.4.1.8691.2.13.1.6.2.1.1 | RowmonitorSerialPortStatusEntry | not-accessible | current | Serial Port Status entry. |
| 1.3.6.1.4.1.8691.2.13.1.6.2.1.1.1 | ColumnmonitorTxCount | read-only | current | View the number of bytes transmitted from the port since the last time the port was initialized. |
| 1.3.6.1.4.1.8691.2.13.1.6.2.1.1.2 | ColumnmonitorRxCount | read-only | current | View the number of bytes received by the port since the last time the port was initialized. |
| 1.3.6.1.4.1.8691.2.13.1.6.2.1.1.3 | ColumnmonitorTxTotalCount | read-only | current | View the number of bytes transmitted from the port since the last time the system was initialized. |
| 1.3.6.1.4.1.8691.2.13.1.6.2.1.1.4 | ColumnmonitorRxTotalCount | read-only | current | View the number of bytes received by the port since the last time the system was initialized. |
| 1.3.6.1.4.1.8691.2.13.1.6.2.1.1.5 | ColumnmonitorDSR | read-only | current | View the current DSR status of this port. |
| 1.3.6.1.4.1.8691.2.13.1.6.2.1.1.6 | ColumnmonitorDTR | read-only | current | View the current DTR status of this port. |
| 1.3.6.1.4.1.8691.2.13.1.6.2.1.1.7 | ColumnmonitorRTS | read-only | current | View the current RTS status of this port. |
| 1.3.6.1.4.1.8691.2.13.1.6.2.1.1.8 | ColumnmonitorCTS | read-only | current | View the current CTS status of this port. |
| 1.3.6.1.4.1.8691.2.13.1.6.2.1.1.9 | ColumnmonitorDCD | read-only | current | View the current DCD status of this port. |
| 1.3.6.1.4.1.8691.2.13.1.6.3 | NodeserialPortErrorCount | |||
| 1.3.6.1.4.1.8691.2.13.1.6.3.1 | TablemonitorSerialPortErrorCountTable | not-accessible | current | Serial Port Error Count table. |
| 1.3.6.1.4.1.8691.2.13.1.6.3.1.1 | RowmonitorSerialPortErrorCountEntry | not-accessible | current | Serial Port Error Count entry. |
| 1.3.6.1.4.1.8691.2.13.1.6.3.1.1.1 | ColumnmonitorErrorCountFrame | read-only | current | View the number of 'Frame' errors for this port. |
| 1.3.6.1.4.1.8691.2.13.1.6.3.1.1.2 | ColumnmonitorErrorCountParity | read-only | current | View the number of 'Parity' errors for this port. |
| 1.3.6.1.4.1.8691.2.13.1.6.3.1.1.3 | ColumnmonitorErrorCountOverrun | read-only | current | View the number of 'Overrun' errors for this port. |
| 1.3.6.1.4.1.8691.2.13.1.6.3.1.1.4 | ColumnmonitorErrorCountBreak | read-only | current | View the number of 'Break' errors for this port. |
| 1.3.6.1.4.1.8691.2.13.1.6.4 | NodeserialPortSettings | |||
| 1.3.6.1.4.1.8691.2.13.1.6.4.1 | TablemonitorSerialPortSettingsTable | not-accessible | current | Serial Port Settings table. |
| 1.3.6.1.4.1.8691.2.13.1.6.4.1.1 | RowmonitorSerialPortSettingsEntry | not-accessible | current | Serial Port Settings entry. |
| 1.3.6.1.4.1.8691.2.13.1.6.4.1.1.1 | ColumnmonitorBaudRate | read-only | current | View the current baudrate of the port. |
| 1.3.6.1.4.1.8691.2.13.1.6.4.1.1.2 | ColumnmonitorDataBits | read-only | current | View the number of bits per byte for the port. |
| 1.3.6.1.4.1.8691.2.13.1.6.4.1.1.3 | ColumnmonitorStopBits | read-only | current | View the number of stop bits for the port. |
| 1.3.6.1.4.1.8691.2.13.1.6.4.1.1.4 | ColumnmonitorParity | read-only | current | View the parity bit for the port. |
| 1.3.6.1.4.1.8691.2.13.1.6.4.1.1.5 | ColumnmonitorRTSCTSFlowControl | read-only | current | View if the port is using RTS/CTS flow control. |
| 1.3.6.1.4.1.8691.2.13.1.6.4.1.1.6 | ColumnmonitorXONXOFFFlowControl | read-only | current | View if the port is using XON/XOFF flow control. |
| 1.3.6.1.4.1.8691.2.13.1.6.4.1.1.7 | ColumnmonitorFIFO | read-only | current | View FIFO status of this port. |
| 1.3.6.1.4.1.8691.2.13.1.6.4.1.1.8 | ColumnmonitorInterface | read-only | current | View the serial interface that the port is using. |
| 1.3.6.1.4.1.8691.2.13.1.6.5 | NodeserialPortBuffering | |||
| 1.3.6.1.4.1.8691.2.13.1.6.5.1 | TablemonitorSerialPortBufferingTable | not-accessible | current | Serial Port Buffering table. |
| 1.3.6.1.4.1.8691.2.13.1.6.5.1.1 | RowmonitorSerialPortBufferingEntry | not-accessible | current | Serial Port Settings entry. |
| 1.3.6.1.4.1.8691.2.13.1.6.5.1.1.1 | ColumnmonitorBuffering | read-only | current | View length of buffered data for the port. The length unit is byte. |
| 1.3.6.1.4.1.8691.2.13.1.6.6 | NodesysWlanStatus | |||
| 1.3.6.1.4.1.8691.2.13.1.6.6.1 | ScalarwlanStatusActiveProfileName | read-only | current | The active profile name. |
| 1.3.6.1.4.1.8691.2.13.1.6.6.2 | ScalarwlanStatusIpConfiguration | read-only | current | The IP configuration mode of the NPort. You can choose from four possible IP configuration modes: Static, DHCP, DHCP/BOOTP, BOOTP. |
| 1.3.6.1.4.1.8691.2.13.1.6.6.3 | ScalarwlanStatusIpAddress | read-only | current | An IP address is a number assigned to a network device (such as a computer) as a permanent address on the network. Computers use the IP address to identify and… |
| 1.3.6.1.4.1.8691.2.13.1.6.6.4 | ScalarwlanStatusNetMask | read-only | current | A subnet mask represents all of the network hosts at one geographic location, in one building, or on the same local area network. When a packet is sent out ove… |
| 1.3.6.1.4.1.8691.2.13.1.6.6.5 | ScalarwlanStatusDefaultGateway | read-only | current | A gateway is a network computer that acts as an entrance to another network. Usually, the computers that control traffic within the network or at the local Int… |
| 1.3.6.1.4.1.8691.2.13.1.6.6.6 | ScalarwlanStatusNetworkType | read-only | current | Network Type of Wireless LAN. The possible values are 'Infrastrcture Mode' and 'Ad-hoc Mode' |
| 1.3.6.1.4.1.8691.2.13.1.6.6.7 | ScalarwlanStatusRFType | read-only | current | RF type of Wireless LAN. The possible values are 'N/A', 'Auto', '802.11a', '802.11b', '802.11g' |
| 1.3.6.1.4.1.8691.2.13.1.6.6.8 | ScalarwlanStatusSSID | read-only | current | The SSID of WLAN. |
| 1.3.6.1.4.1.8691.2.13.1.6.6.9 | ScalarwlanStatusChannel | read-only | current | The currently used channel. |
| 1.3.6.1.4.1.8691.2.13.1.6.6.10 | ScalarwlanStatusAuthentication | read-only | current | Authentication type of Wireless LAN. The possible values are 'Unknown', 'Open System', 'Shared Key', 'WPA', 'WPA-PSK', 'WPA2', 'WPA2-PSK' |
| 1.3.6.1.4.1.8691.2.13.1.6.6.11 | ScalarwlanStatusEncryption | read-only | current | Show encryption type of Wireless LAN. |
| 1.3.6.1.4.1.8691.2.13.1.6.6.12 | ScalarwlanStatusRegion | read-only | current | Display region. The possible values are 'US', 'EU', 'JP' |
| 1.3.6.1.4.1.8691.2.13.1.6.6.13 | ScalarwlanStatusSignalStrength | read-only | current | The signal strength of Wireless LAN. |
| 1.3.6.1.4.1.8691.2.13.1.6.6.14 | ScalarwlanStatusConnectionSpeed | read-only | current | The connection speed of Wireless LAN. |
| 1.3.6.1.4.1.8691.2.13.1.6.6.15 | ScalarwlanStatusCurrentBSSID | read-only | current | The current BSSID of Wireless LAN. |
| 1.3.6.1.4.1.8691.2.13.1.7 | NodeactivateSettings | |||
| 1.3.6.1.4.1.8691.2.13.1.7.1 | ScalardoActivate | write-only | current | Activate current settings. |
| 1.3.6.1.4.1.8691.2.13.1.8 | Noderestart | |||
| 1.3.6.1.4.1.8691.2.13.1.8.1 | ScalarrestartPorts | write-only | current | Restart serial port. Restarting will cause port reseting. |
| 1.3.6.1.4.1.8691.2.13.1.8.2 | ScalarrestartSystem | write-only | current | Restart the NPort W2x50A series device server. Be sure to save all of your configuration changes before you restart the system. Otherwise, all of the changes w… |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| PortList | OCTET STRING | current | Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents… |