MPLS-TE-MIB
124 objects
This MIB module contains managed object definitions for MPLS Traffic Engineering (TE) as defined in: Extensions to RSVP for LSP Tunnels, Awduche et al, Internet Draft <draft-ietf-mpls- rsvp-lsp-tunnel-07.txt>, August 2000; Constraint- Based LSP Setup using LDP, B. Jamoussi, Internet Draft <draft-ietf-mpls-cr-ldp-04.txt>, July 2000; Requirements for Traffic Engineering Over MPLS, Awduche, D., J. Malcolm, J., Agogbua, J., O'Dell, M., J. McManus, <rfc2702.txt>, September 1999.
Imported Objects
| IF-MIB | InterfaceIndexOrZero |
| INET-ADDRESS-MIB | InetAddressIPv4 InetAddressIPv6 |
| MPLS-LSR-MIB | MplsBitRate MplsBurstSize MplsLSPID |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 experimental Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | DisplayString RowPointer RowStatus StorageType TEXTUAL-CONVENTION TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.3.95 | IdentitymplsTeMIB | This MIB module contains managed object definitions for MPLS Traffic Engineering (TE) as defined in: Extensions to RSVP for LSP Tunnels, Awduche et al, Interne… | ||
| 1.3.6.1.3.95.1 | NodemplsTeScalars | |||
| 1.3.6.1.3.95.1.1 | ScalarmplsTunnelConfigured | read-only | current | The number of tunnels configured on this device. A tunnel is considered configured if the mplsTunnelRowStatus is active(1). |
| 1.3.6.1.3.95.1.2 | ScalarmplsTunnelActive | read-only | current | The number of tunnels active on this device. A tunnel is considered active if the mplsTunnelOperStatus is up(1). |
| 1.3.6.1.3.95.1.3 | ScalarmplsTunnelTEDistProto | read-only | current | The traffic engineering distribution protocol(s) used by this LSR. Note that an LSR may support more than one distribution protocols simultaneously. |
| 1.3.6.1.3.95.1.4 | ScalarmplsTunnelMaxHops | read-only | current | The maximum number of hops that can be specified for a tunnel on this device. |
| 1.3.6.1.3.95.2 | NodemplsTeObjects | |||
| 1.3.6.1.3.95.2.1 | ScalarmplsTunnelIndexNext | read-only | current | This object contains the next appropriate value to be used for mplsTunnelIndex when creating entries in mplsTunnelTable. If the number of unassigned entries is… |
| 1.3.6.1.3.95.2.2 | TablemplsTunnelTable | not-accessible | current | The mplsTunnelTable allows new MPLS tunnels to be created between an LSR and a remote endpoint, and existing tunnels to be reconfigured or removed. Note that o… |
| 1.3.6.1.3.95.2.2.1 | RowmplsTunnelEntry | not-accessible | current | An entry in this table represents an MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signaling pro… |
| 1.3.6.1.3.95.2.2.1.1 | ColumnmplsTunnelIndex | not-accessible | current | Uniquely identifies this row. |
| 1.3.6.1.3.95.2.2.1.2 | ColumnmplsTunnelInstance | not-accessible | current | Uniquely identifies an instance of a tunnel. It is useful to identify multiple instances of tunnels for the purposes of backup and parallel tunnels. |
| 1.3.6.1.3.95.2.2.1.3 | ColumnmplsTunnelIngressLSRId | not-accessible | current | The purpose of this object is to uniquely identity a tunnel within a network. When the MPLS signalling protoocol is rsvp(2) this value should mimic the Extende… |
| 1.3.6.1.3.95.2.2.1.4 | ColumnmplsTunnelEgressLSRId | read-only | current | Specifies the egress LSR Id. |
| 1.3.6.1.3.95.2.2.1.5 | ColumnmplsTunnelName | read-create | current | The canonical name assigned to the tunnel. This name can be used to refer to the tunnel on the LSR�s console port. If mplsTunnelIsIf is set to true then the … |
| 1.3.6.1.3.95.2.2.1.6 | ColumnmplsTunnelDescr | read-create | current | A textual string containing information about the tunnel. If there is no description this object contains a zero length string. |
| 1.3.6.1.3.95.2.2.1.7 | ColumnmplsTunnelIsIf | read-create | current | Denotes whether or not this tunnel corresponds to an interface represented in the interfaces group table. Note that if this variable is set to true then the if… |
| 1.3.6.1.3.95.2.2.1.8 | ColumnmplsTunnelIfIndex | read-only | current | If mplsTunnelIsIf is set to true, then this value contains the LSR-assigned ifIndex which corresponds to an entry in the interfaces table. Otherwise this varia… |
| 1.3.6.1.3.95.2.2.1.9 | ColumnmplsTunnelXCPointer | read-create | current | This variable points to a row in the mplsXCTable. This table identifies the segments that compose this tunnel, their characteristics, and relationships to each… |
| 1.3.6.1.3.95.2.2.1.10 | ColumnmplsTunnelSignallingProto | read-create | current | The signaling protocol, if any, which was used to setup this tunnel. |
| 1.3.6.1.3.95.2.2.1.11 | ColumnmplsTunnelSetupPrio | read-create | current | Indicates the setup priority of this tunnel. |
| 1.3.6.1.3.95.2.2.1.12 | ColumnmplsTunnelHoldingPrio | read-create | current | Indicates the holding priority for this tunnel. |
| 1.3.6.1.3.95.2.2.1.13 | ColumnmplsTunnelSessionAttributes | read-create | current | This bitmask indicates optional session values for this tunnel. The following describes these bitfields: fastRerouteThis flag indicates that the any tunnel hop… |
| 1.3.6.1.3.95.2.2.1.14 | ColumnmplsTunnelOwner | read-create | current | Indicates which protocol created and is responsible for managing this tunnel. Values rsvp(2) and crldp(3) should not be used at the head-end of a MPLS tunnel. |
| 1.3.6.1.3.95.2.2.1.15 | ColumnmplsTunnelLocalProtectInUse | read-create | current | Indicates that the local repair mechanism is in use to maintain this tunnel (usually in the face of an outage of the link it was previously routed over). |
| 1.3.6.1.3.95.2.2.1.16 | ColumnmplsTunnelResourcePointer | read-create | current | This variable represents a pointer to the traffic parameter specification for this tunnel. This value may point at an entry in the mplsTunnelResourceEntry to i… |
| 1.3.6.1.3.95.2.2.1.17 | ColumnmplsTunnelInstancePriority | read-create | current | This value indicates which priority, in descending order, with 0 indicating the lowest priority, within a group of tunnel instances. A group of tunnel instance… |
| 1.3.6.1.3.95.2.2.1.18 | ColumnmplsTunnelHopTableIndex | read-create | current | Index into the mplsTunnelHopTable entry that specifies the explicit route hops for this tunnel. |
| 1.3.6.1.3.95.2.2.1.19 | ColumnmplsTunnelARHopTableIndex | read-only | current | Index into the mplsTunnelARHopTable entry that specifies the actual hops traversed by the tunnel. |
| 1.3.6.1.3.95.2.2.1.20 | ColumnmplsTunnelCHopTableIndex | read-only | current | Index into the mplsTunnelCHopTable entry that specifies the computed hops traversed by the tunnel. |
| 1.3.6.1.3.95.2.2.1.21 | ColumnmplsTunnelPrimaryInstance | read-only | current | Specifies the instance index of the primary instance of this tunnel. |
| 1.3.6.1.3.95.2.2.1.22 | ColumnmplsTunnelPrimaryTimeUp | read-only | current | Specifies the total time the primary instance of this tunnel has been active. The primary instance of this tunnel is defined in mplsTunnelPrimaryInstance. |
| 1.3.6.1.3.95.2.2.1.23 | ColumnmplsTunnelPathChanges | read-only | current | Specifies the number of times the paths has changed for this tunnel. |
| 1.3.6.1.3.95.2.2.1.24 | ColumnmplsTunnelLastPathChange | read-only | current | Specifies the time since the last path change for this tunnel. |
| 1.3.6.1.3.95.2.2.1.25 | ColumnmplsTunnelCreationTime | read-only | current | Specifies the value of SysUpTime when the first instance of this tunnel came into existence. |
| 1.3.6.1.3.95.2.2.1.26 | ColumnmplsTunnelStateTransitions | read-only | current | Specifies the number of times the state of this tunnel instance has changed. |
| 1.3.6.1.3.95.2.2.1.27 | ColumnmplsTunnelIncludeAnyAffinity | read-create | current | A link satisfies the include-any constraint if and only if the constraint is zero, or the link and the constraint have a resource class in common. |
| 1.3.6.1.3.95.2.2.1.28 | ColumnmplsTunnelIncludeAllAffinity | read-create | current | A link satisfies the include-all constraint if and only if the link contains all of the adminstrative groups specified in the constraint. |
| 1.3.6.1.3.95.2.2.1.29 | ColumnmplsTunnelExcludeAllAffinity | read-create | current | A link satisfies the exclude-all constraint if and only if the link contains none of the adminstrative groups specifie in the constraint. |
| 1.3.6.1.3.95.2.2.1.30 | ColumnmplsTunnelPathInUse | read-create | current | This value denotes the configured path that was chosen for this tunnel. This value reflects the secondary index into the TunnelHopTable. This path may not exac… |
| 1.3.6.1.3.95.2.2.1.31 | ColumnmplsTunnelRole | read-create | current | This value signifies the role that this tunnel entry/instance represents. This value MUST be set to head(1) at the originating point of the tunnel. This value … |
| 1.3.6.1.3.95.2.2.1.32 | ColumnmplsTunnelTotalUpTime | read-create | current | This value represents the aggregate up time for all instances of this tunnel, if available. If this value is unavailable, it MUST return a value of 0. |
| 1.3.6.1.3.95.2.2.1.33 | ColumnmplsTunnelInstanceUpTime | read-create | current | This value identifies the total time that this tunnel instance's operStatus has been Up(1). |
| 1.3.6.1.3.95.2.2.1.34 | ColumnmplsTunnelAdminStatus | read-create | current | Indicates the desired operational status of this tunnel. |
| 1.3.6.1.3.95.2.2.1.35 | ColumnmplsTunnelOperStatus | read-only | current | Indicates the actual operational status of this tunnel, which is typically but not limited to, a function of the state of individual segments of this tunnel. |
| 1.3.6.1.3.95.2.2.1.36 | ColumnmplsTunnelRowStatus | read-create | current | This variable is used to create, modify, and/or delete a row in this table. |
| 1.3.6.1.3.95.2.2.1.37 | ColumnmplsTunnelStorageType | read-create | current | This variable indicates the storage type for this object. |
| 1.3.6.1.3.95.2.3 | ScalarmplsTunnelHopListIndexNext | read-only | current | This object contains an appropriate value to be used for mplsTunnelHopListIndex when creating entries in the mplsTunnelHopTable. If the number of unassigned en… |
| 1.3.6.1.3.95.2.4 | TablemplsTunnelHopTable | not-accessible | current | The mplsTunnelHopTable is used to indicate the hops, strict or loose, for an MPLS tunnel defined in mplsTunnelTable, when it is established via signaling, for … |
| 1.3.6.1.3.95.2.4.1 | RowmplsTunnelHopEntry | not-accessible | current | An entry in this table represents a tunnel hop. An entry is created by a network administrator for signaled ERLSP set up by an MPLS signaling protocol. |
| 1.3.6.1.3.95.2.4.1.1 | ColumnmplsTunnelHopListIndex | not-accessible | current | Primary index into this table identifying a particular explicit route object. |
| 1.3.6.1.3.95.2.4.1.2 | ColumnmplsPathOptionIndex | not-accessible | current | Secondary index into this table identifying a particular group of hops representing a particular configured path. This is otherwise known as a path option. |
| 1.3.6.1.3.95.2.4.1.3 | ColumnmplsTunnelHopIndex | not-accessible | current | Secondary index into this table identifying a particular hop. |
| 1.3.6.1.3.95.2.4.1.4 | ColumnmplsTunnelHopAddrType | read-create | current | Denotes the address type of this tunnel hop. |
| 1.3.6.1.3.95.2.4.1.5 | ColumnmplsTunnelHopIpv4Addr | read-create | current | If mplsTunnelHopAddrType is set to ipV4(1), then this value will contain the IPv4 address of this hop. This object is otherwise insignificant and should contai… |
| 1.3.6.1.3.95.2.4.1.6 | ColumnmplsTunnelHopIpv4PrefixLen | read-create | current | If mplsTunnelHopAddrType is ipV4(1), then the prefix length for this hop's IPv4 address is contained herein. This object is otherwise insignificant and should … |
| 1.3.6.1.3.95.2.4.1.7 | ColumnmplsTunnelHopIpv6Addr | read-create | current | If the mplsTunnelHopAddrType is set to ipV6(2), then this variable contains the IPv6 address of this hop. This object is otherwise insignificant and should con… |
| 1.3.6.1.3.95.2.4.1.8 | ColumnmplsTunnelHopIpv6PrefixLen | read-create | current | If mplsTunnelHopAddrType is set to ipV6(2), this value will contain the prefix length for this hop's IPv6 address. This object is otherwise insignificant and s… |
| 1.3.6.1.3.95.2.4.1.9 | ColumnmplsTunnelHopAsNumber | read-create | current | If mplsTunnelHopAddrType is set to asNumber(3), then this value will contain the AS number of this hop. This object is otherwise insignificant and should conta… |
| 1.3.6.1.3.95.2.4.1.10 | ColumnmplsTunnelHopLspId | read-create | current | If mplsTunnelHopAddrType is set to lspid(4), then this value will contain the LSPID of a tunnel of this hop. The present tunnel being configured is �tunneled… |
| 1.3.6.1.3.95.2.4.1.11 | ColumnmplsTunnelHopType | read-create | current | Denotes whether this tunnel hop is routed in a strict or loose fashion. |
| 1.3.6.1.3.95.2.4.1.12 | ColumnmplsTunnelHopRowStatus | read-create | current | This variable is used to create, modify, and/or delete a row in this table. |
| 1.3.6.1.3.95.2.4.1.13 | ColumnmplsTunnelHopStorageType | read-create | current | This variable indicates the storage type for this object. |
| 1.3.6.1.3.95.2.5 | ScalarmplsTunnelResourceIndexNext | read-only | current | This object contains the next appropriate value to be used for mplsTunnelResourceIndex when creating entries in the mplsTunnelResourceTable. If the number of u… |
| 1.3.6.1.3.95.2.6 | TablemplsTunnelResourceTable | not-accessible | current | The mplsTunnelResourceTable allows a manager to specify which resources are desired for an MPLS tunnel. This table also allows several tunnels to point to a si… |
| 1.3.6.1.3.95.2.6.1 | RowmplsTunnelResourceEntry | not-accessible | current | An entry in this table represents a set of resources for an MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed b… |
| 1.3.6.1.3.95.2.6.1.1 | ColumnmplsTunnelResourceIndex | not-accessible | current | Uniquely identifies this row. |
| 1.3.6.1.3.95.2.6.1.2 | ColumnmplsTunnelResourceMaxRate | read-create | current | The maximum rate in bits/second. Note that setting mplsTunnelResourceMaxRate, mplsTunnelResourceMeanRate, and mplsTunnelResourceMaxBurstSize to 0 indicates bes… |
| 1.3.6.1.3.95.2.6.1.3 | ColumnmplsTunnelResourceMeanRate | read-create | current | This object is copied into an instance of mplsTrafficParamMeanRate in the mplsTrafficParamTable. The OID of this table entry is then copied into the correspond… |
| 1.3.6.1.3.95.2.6.1.4 | ColumnmplsTunnelResourceMaxBurstSize | read-create | current | The maximum burst size in bytes. This object is copied to mplsInSegmentMaxBurstSize of the corresponding in-segment. When resource allocation is performed as r… |
| 1.3.6.1.3.95.2.6.1.5 | ColumnmplsTunnelResourceRowStatus | read-create | current | This variable is used to create, modify, and/or delete a row in this table. |
| 1.3.6.1.3.95.2.6.1.6 | ColumnmplsTunnelResourceStorageType | read-create | current | This variable indicates the storage type for this object. |
| 1.3.6.1.3.95.2.7 | TablemplsTunnelARHopTable | not-accessible | current | The mplsTunnelARHopTable is used to indicate the hops, strict or loose, for an MPLS tunnel defined in mplsTunnelTable, as reported by the MPLS signaling protoc… |
| 1.3.6.1.3.95.2.7.1 | RowmplsTunnelARHopEntry | not-accessible | current | An entry in this table represents a tunnel hop. An entry is created by a network administrator for signaled ERLSP set up by an MPLS signaling protocol. |
| 1.3.6.1.3.95.2.7.1.1 | ColumnmplsTunnelARHopListIndex | not-accessible | current | Primary index into this table identifying a particular recorded hop list. |
| 1.3.6.1.3.95.2.7.1.2 | ColumnmplsTunnelARHopIndex | not-accessible | current | Secondary index into this table identifying the particular hop. |
| 1.3.6.1.3.95.2.7.1.3 | ColumnmplsTunnelARHopAddrType | read-only | current | Denotes the address type of this tunnel hop. |
| 1.3.6.1.3.95.2.7.1.4 | ColumnmplsTunnelARHopIpv4Addr | read-only | current | If mplsTunnelARHopAddrType is set to ipV4(1), then this value will contain the IPv4 address of this hop. This object is otherwise insignificant and should cont… |
| 1.3.6.1.3.95.2.7.1.5 | ColumnmplsTunnelARHopIpv4PrefixLen | read-only | current | If mplsTunnelARHopAddrType is ipV4(1), then the prefix length for this hop's IPv4 address is contained herein. This object is otherwise insignificant and shoul… |
| 1.3.6.1.3.95.2.7.1.6 | ColumnmplsTunnelARHopIpv6Addr | read-only | current | If the mplsTunnelARHopAddrType is set to ipV6(2), then this variable contains the IPv6 address of this hop. This object is otherwise insignificant and should c… |
| 1.3.6.1.3.95.2.7.1.7 | ColumnmplsTunnelARHopIpv6PrefixLen | read-only | current | If mplsTunnelARHopAddrType is set to ipV6(2), this value will contain the prefix length for this hop's IPv6 address. This object is otherwise insignificant and… |
| 1.3.6.1.3.95.2.7.1.8 | ColumnmplsTunnelARHopAsNumber | read-only | current | If mplsTunnelARHopAddrType is set to asNumber(3), then this value will contain the AS number of this hop. This object is otherwise insignificant and should con… |
| 1.3.6.1.3.95.2.7.1.9 | ColumnmplsTunnelARHopType | read-only | current | Denotes whether this is tunnel hop is routed in a strict or loose fashion. |
| 1.3.6.1.3.95.2.8 | TablemplsTunnelCHopTable | not-accessible | current | The mplsTunnelCHopTable is used to indicate the hops, strict or loose, for an MPLS tunnel defined in mplsTunnelTable, as computed by a constraint- based routin… |
| 1.3.6.1.3.95.2.8.1 | RowmplsTunnelCHopEntry | not-accessible | current | An entry in this table represents a tunnel hop. An entry in this table is created by a constraint- based routing protocol based on the hops specified in the co… |
| 1.3.6.1.3.95.2.8.1.1 | ColumnmplsTunnelCHopListIndex | not-accessible | current | Primary index into this table identifying a particular computed hop list. |
| 1.3.6.1.3.95.2.8.1.2 | ColumnmplsTunnelCHopIndex | not-accessible | current | Secondary index into this table identifying the particular hop. |
| 1.3.6.1.3.95.2.8.1.3 | ColumnmplsTunnelCHopAddrType | read-only | current | Denotes the address type of this tunnel hop. |
| 1.3.6.1.3.95.2.8.1.4 | ColumnmplsTunnelCHopIpv4Addr | read-only | current | If mplsTunnelCHopAddrType is set to ipV4(1), then this value will contain the IPv4 address of this hop. This object is otherwise insignificant and should conta… |
| 1.3.6.1.3.95.2.8.1.5 | ColumnmplsTunnelCHopIpv4PrefixLen | read-only | current | If mplsTunnelCHopAddrType is ipV4(1), then the prefix length for this hop's IPv4 address is contained herein. This object is otherwise insignificant and should… |
| 1.3.6.1.3.95.2.8.1.6 | ColumnmplsTunnelCHopIpv6Addr | read-only | current | If the mplsTunnelCHopAddrType is set to ipV6(2), then this variable contains the IPv6 address of this hop. This object is otherwise insignificant and should co… |
| 1.3.6.1.3.95.2.8.1.7 | ColumnmplsTunnelCHopIpv6PrefixLen | read-only | current | If mplsTunnelCHopAddrType is set to ipV6(2), this value will contain the prefix length for this hop's IPv6 address. This object is otherwise insignificant and … |
| 1.3.6.1.3.95.2.8.1.8 | ColumnmplsTunnelCHopAsNumber | read-only | current | If mplsTunnelCHopAddrType is set to asNumber(3), then this value will contain the AS number of this hop. This object is otherwise insignificant and should cont… |
| 1.3.6.1.3.95.2.8.1.9 | ColumnmplsTunnelCHopType | read-only | current | Denotes whether this is tunnel hop is routed in a strict or loose fashion. |
| 1.3.6.1.3.95.2.9 | TablemplsTunnelPerfTable | not-accessible | current | This table provides per-tunnel MPLS performance information. |
| 1.3.6.1.3.95.2.9.1 | RowmplsTunnelPerfEntry | not-accessible | current | An entry in this table is created by the LSR for every tunnel. Its is an extension to mplsTunnelEntry. |
| 1.3.6.1.3.95.2.9.1.1 | ColumnmplsTunnelPerfPackets | read-only | current | Number of packets forwarded by the tunnel. |
| 1.3.6.1.3.95.2.9.1.2 | ColumnmplsTunnelPerfHCPackets | read-only | current | High capacity counter for number of packets forwarded by the tunnel. |
| 1.3.6.1.3.95.2.9.1.3 | ColumnmplsTunnelPerfErrors | read-only | current | Number of errored packets. |
| 1.3.6.1.3.95.2.9.1.4 | ColumnmplsTunnelPerfBytes | read-only | current | Number of bytes forwarded by the tunnel. |
| 1.3.6.1.3.95.2.9.1.5 | ColumnmplsTunnelPerfHCBytes | read-only | current | High capacity counter for number of bytes forwarded by the tunnel. |
| 1.3.6.1.3.95.2.10 | ScalarmplsTunnelTrapEnable | read-write | current | If this object is true, then it enables the generation of mplsTunnelUp and mplsTunnelDown traps, otherwise these traps are not emitted. |
| 1.3.6.1.3.95.3 | NodemplsTeNotifications | |||
| 1.3.6.1.3.95.3.0 | NodemplsTeNotifyPrefix | |||
| 1.3.6.1.3.95.3.0.1 | NotificationmplsTunnelUp | current | This notification is generated when a mplsTunnelOperStatus object for one of the configured tunnels is about to leave the down state and transition into some o… | |
| 1.3.6.1.3.95.3.0.2 | NotificationmplsTunnelDown | current | This notification is generated when a mplsTunnelOperStatus object for one of the configured tunnels is about to enter the down state from some other state (but… | |
| 1.3.6.1.3.95.3.0.3 | NotificationmplsTunnelRerouted | current | This notification is generated when a tunnel is rerouted or re-optimized. If the Actual Path is used, then this object MAY contain the new path for this tunnel… | |
| 1.3.6.1.3.95.4 | NodemplsTeConformance | |||
| 1.3.6.1.3.95.4.1 | NodemplsTeGroups | |||
| 1.3.6.1.3.95.4.1.1 | GroupmplsTunnelGroup | current | Necessary, but not sufficient, set of objects to implement tunnels. In addition, depending on the type of the tunnels supported (for example, manually configur… | |
| 1.3.6.1.3.95.4.1.2 | GroupmplsTunnelManualGroup | current | Object(s) needed to implement manually configured tunnels. | |
| 1.3.6.1.3.95.4.1.3 | GroupmplsTunnelSignaledGroup | current | Object needed to implement signaled tunnels. | |
| 1.3.6.1.3.95.4.1.4 | GroupmplsTunnelScalarGroup | current | Scalar object needed to implement MPLS tunnels. | |
| 1.3.6.1.3.95.4.1.5 | GroupmplsTunnelIsIntfcGroup | current | Objects needed to implement tunnels that are interfaces. | |
| 1.3.6.1.3.95.4.1.6 | GroupmplsTunnelIsNotIntfcGroup | current | Objects needed to implement tunnels that are not interfaces. | |
| 1.3.6.1.3.95.4.1.7 | GroupmplsTunnelOptionalGroup | current | The objects in this group are optional. | |
| 1.3.6.1.3.95.4.1.8 | GroupmplsTeNotificationGroup | current | Set of notifications implemented in this module. None is mandatory. | |
| 1.3.6.1.3.95.4.2 | NodemplsTeCompliances | |||
| 1.3.6.1.3.95.4.2.1 | CompliancemplsTeModuleCompliance | read-only | current | Compliance statement for agents that support the MPLS TE MIB. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| MplsLsrId | Unsigned32 | current | A unique identifier for an MPLS LSR. This MAY represent an IpV4 address. |
| MplsPathIndex | Unsigned32 | current | A unique identifier used to identify a specific path used by a tunnel. |
| MplsPathIndexOrZero | Unsigned32 | current | A unique identifier used to identify a specific path used by a tunnel. If this value is set to 0, it indicates that no path is in use. |
| MplsTunnelIndex | Integer32 (1..65535) | current | Index into mplsTunnelTable. |
| MplsTunnelInstanceIndex | Unsigned32 (0..65535) | current | Instance index into mplsTunnelTable. |