Modem-MIB
114 objects
The MIB module for management of dial-up modems.
Imported Objects
| RFC1213-MIB | mib-2 |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Integer32 MODULE-IDENTITY OBJECT-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.38 | NodemdmMib | |||
| 1.3.6.1.2.1.38.1 | IdentitymdmMIB | The MIB module for management of dial-up modems. | ||
| 1.3.6.1.2.1.38.1.1 | NodemdmMIBObjects | |||
| 1.3.6.1.2.1.38.1.1.1 | ScalarmdmNumber | read-only | current | The number of modem rows in the modem table. This value defines the maximum value of the mdmIndex object. |
| 1.3.6.1.2.1.38.1.1.2 | TablemdmIDTable | not-accessible | current | The base table for the modems managed by this MIB. The mdmLineTable, mdmDTEInterfaceTable, mdmCallControlTable, and mdmStatsTable all augment the rows defined … |
| 1.3.6.1.2.1.38.1.1.2.1 | RowmdmIDEntry | not-accessible | current | Entries in this table are created only by the agent. One entry exists for each modem managed by the agent. |
| 1.3.6.1.2.1.38.1.1.2.1.1 | ColumnmdmIndex | not-accessible | current | A unique number for each modem that ranges from 1 to mdmNumber. The value must remain constant at least from one re-initialization of the network management ag… |
| 1.3.6.1.2.1.38.1.1.2.1.2 | ColumnmdmIDManufacturerOID | read-only | current | This value is intended to identify the manufacturer, model, and version of this modem. This may be used to identify the existance of enterprise-specific functi… |
| 1.3.6.1.2.1.38.1.1.2.1.3 | ColumnmdmIDProductDetails | read-only | current | A textual description of this device, including the manufacturer's name, modem model name, hardware revision, firmware revision, and optionally, its serial num… |
| 1.3.6.1.2.1.38.1.1.3 | TablemdmLineTable | not-accessible | current | The modem Line Table augments the modem ID table. |
| 1.3.6.1.2.1.38.1.1.3.1 | RowmdmLineEntry | not-accessible | current | Entries in this table are created only by the agent. One entry exists for each modem managed by the agent. |
| 1.3.6.1.2.1.38.1.1.3.1.1 | ColumnmdmLineCarrierLossTime | read-write | current | Duration in 10ths of a second the modem waits after loss of carrier before hanging up. If this value is set to `255', the modem will not hang up upon loss of c… |
| 1.3.6.1.2.1.38.1.1.3.1.2 | ColumnmdmLineState | read-write | current | Allows the inspection and alteration of the state of the modem. Management commands may change the state to `on- hook', `busied-out', or `reset' from any state… |
| 1.3.6.1.2.1.38.1.1.4 | TablemdmLineCapabilitiesTable | not-accessible | current | A list of protocol capabilities for this modem. |
| 1.3.6.1.2.1.38.1.1.4.1 | RowmdmLineCapabilitiesEntry | not-accessible | current | A listing of the protocol(s) that this modem is capable of. Entries in this table are created only by the agent. One entry exists for each protocol that the mo… |
| 1.3.6.1.2.1.38.1.1.4.1.1 | ColumnmdmLineCapabilitiesIndex | not-accessible | current | A unique index for this capabilities entry. |
| 1.3.6.1.2.1.38.1.1.4.1.2 | ColumnmdmLineCapabilitiesID | read-only | current | An identifier for this capability. Standard protocol capabilities will have identifiers registered in this document or other companion standards documents. Pro… |
| 1.3.6.1.2.1.38.1.1.4.1.3 | ColumnmdmLineCapabilitiesEnableRequested | read-write | current | The requested configuration of this capability. If this value is 'disabled(1)', this is a request to disable this protocol. If this value is 'preferred(3)', th… |
| 1.3.6.1.2.1.38.1.1.4.1.4 | ColumnmdmLineCapabilitiesEnableGranted | read-only | current | The actual configuration of this capability. The agent shall attempt to set this as close as possible to the associated mdmLineCapabilitiesEnableRequested valu… |
| 1.3.6.1.2.1.38.1.1.5 | NodemdmLineCapabilities | |||
| 1.3.6.1.2.1.38.1.1.5.1 | IdentitymdmLineCapabilitiesV21 | current | ITU V.21 | |
| 1.3.6.1.2.1.38.1.1.5.2 | IdentitymdmLineCapabilitiesV22 | current | ITU V.22 | |
| 1.3.6.1.2.1.38.1.1.5.3 | IdentitymdmLineCapabilitiesV22bis | current | ITU V.22bis | |
| 1.3.6.1.2.1.38.1.1.5.4 | IdentitymdmLineCapabilitiesV23CC | current | ITU V.23CC | |
| 1.3.6.1.2.1.38.1.1.5.5 | IdentitymdmLineCapabilitiesV23SC | current | ITU V.23SC | |
| 1.3.6.1.2.1.38.1.1.5.6 | IdentitymdmLineCapabilitiesV25bis | current | ITU V.25bis | |
| 1.3.6.1.2.1.38.1.1.5.7 | IdentitymdmLineCapabilitiesV26bis | current | ITU V.26bis | |
| 1.3.6.1.2.1.38.1.1.5.8 | IdentitymdmLineCapabilitiesV26ter | current | ITU V.26ter | |
| 1.3.6.1.2.1.38.1.1.5.9 | IdentitymdmLineCapabilitiesV27ter | current | ITU V.27ter | |
| 1.3.6.1.2.1.38.1.1.5.10 | IdentitymdmLineCapabilitiesV32 | current | ITU V.32 | |
| 1.3.6.1.2.1.38.1.1.5.11 | IdentitymdmLineCapabilitiesV32bis | current | ITU V.32bis | |
| 1.3.6.1.2.1.38.1.1.5.12 | IdentitymdmLineCapabilitiesV32terbo | current | ITU V.32terbo | |
| 1.3.6.1.2.1.38.1.1.5.13 | IdentitymdmLineCapabilitiesVFC | current | ITU V.FC | |
| 1.3.6.1.2.1.38.1.1.5.14 | IdentitymdmLineCapabilitiesV34 | current | ITU V.34 | |
| 1.3.6.1.2.1.38.1.1.5.15 | IdentitymdmLineCapabilitiesV42 | current | ITU V.42 | |
| 1.3.6.1.2.1.38.1.1.5.16 | IdentitymdmLineCapabilitiesV42bis | current | ITU V.42bis | |
| 1.3.6.1.2.1.38.1.1.5.17 | IdentitymdmLineCapabilitiesMNP1 | current | MNP1 | |
| 1.3.6.1.2.1.38.1.1.5.18 | IdentitymdmLineCapabilitiesMNP2 | current | MNP2 | |
| 1.3.6.1.2.1.38.1.1.5.19 | IdentitymdmLineCapabilitiesMNP3 | current | MNP3 | |
| 1.3.6.1.2.1.38.1.1.5.20 | IdentitymdmLineCapabilitiesMNP4 | current | MNP4 | |
| 1.3.6.1.2.1.38.1.1.5.21 | IdentitymdmLineCapabilitiesMNP5 | current | MNP5 | |
| 1.3.6.1.2.1.38.1.1.5.22 | IdentitymdmLineCapabilitiesMNP6 | current | MNP6 | |
| 1.3.6.1.2.1.38.1.1.5.23 | IdentitymdmLineCapabilitiesMNP7 | current | MNP7 | |
| 1.3.6.1.2.1.38.1.1.5.24 | IdentitymdmLineCapabilitiesMNP8 | current | MNP8 | |
| 1.3.6.1.2.1.38.1.1.5.25 | IdentitymdmLineCapabilitiesMNP9 | current | MNP9 | |
| 1.3.6.1.2.1.38.1.1.5.26 | IdentitymdmLineCapabilitiesMNP10 | current | MNP10 | |
| 1.3.6.1.2.1.38.1.1.5.27 | IdentitymdmLineCapabilitiesV29 | current | ITU V.29 | |
| 1.3.6.1.2.1.38.1.1.5.28 | IdentitymdmLineCapabilitiesV33 | current | ITU V.33 | |
| 1.3.6.1.2.1.38.1.1.5.29 | IdentitymdmLineCapabilitiesBell208 | current | Bell 208 | |
| 1.3.6.1.2.1.38.1.1.6 | TablemdmDTEInterfaceTable | not-accessible | current | The modem DTE Interface Table augments the modem ID table. |
| 1.3.6.1.2.1.38.1.1.6.1 | RowmdmDTEInterfaceEntry | not-accessible | current | Entries in this table are created only by the agent. One entry exists for each modem managed by the agent. |
| 1.3.6.1.2.1.38.1.1.6.1.1 | ColumnmdmDTEActionDTROnToOff | read-write | current | Defines the action the modem will take when DTR drops. If the value is set to ignore(1), the modem takes no action when DTR drops. Typically, mdmDTEActionDTROf… |
| 1.3.6.1.2.1.38.1.1.6.1.2 | ColumnmdmDTEActionDTROffToOn | read-write | current | Defines the action the modem will take when DTR is raised. If the value is set to ignore(1), the modem takes no action when DTR is raised. Typically, mdmDTEAct… |
| 1.3.6.1.2.1.38.1.1.6.1.3 | ColumnmdmDTESyncTimingSource | read-write | current | The clock source for synchronous transmissions. If set to internal(1), the modem is the clock source and sends the clock signals to the DTE. If set to external… |
| 1.3.6.1.2.1.38.1.1.6.1.4 | ColumnmdmDTESyncAsyncMode | read-write | current | The operational mode of the modem. If the value is syncAfterDial(3), the modem will accept commands in asynchronous mode and change to synchronous mode to pass… |
| 1.3.6.1.2.1.38.1.1.6.1.5 | ColumnmdmDTEInactivityTimeout | read-write | current | The amount of idle time in minutes that the modem will wait before disconnecting a connection. When a call is connected and no data is transferred (continuous … |
| 1.3.6.1.2.1.38.1.1.7 | TablemdmCallControlTable | not-accessible | current | The modem Call Control Table augments the modem ID table. |
| 1.3.6.1.2.1.38.1.1.7.1 | RowmdmCallControlEntry | not-accessible | current | Entries in this table are created only by the agent. One entry exists for each modem managed by the agent. |
| 1.3.6.1.2.1.38.1.1.7.1.1 | ColumnmdmCCRingsBeforeAnswer | read-write | current | Determines which ring the modem will wait to answer the phone on. If this value is `0', the modem will not go offhook and answer a call when a ring signal is d… |
| 1.3.6.1.2.1.38.1.1.7.1.2 | ColumnmdmCCCallSetUpFailTimer | read-write | current | This parameter specifies the amount of time, in seconds, that the modem shall allow between either answering a call (automatically or manually) or completion o… |
| 1.3.6.1.2.1.38.1.1.7.1.3 | ColumnmdmCCResultCodeEnable | read-write | current | When disabled, the DCE shall issue no 'result codes' of any kind to the DTE either in response to unsolicited events (eg. ring signal), or commands. In TIA-602… |
| 1.3.6.1.2.1.38.1.1.7.1.4 | ColumnmdmCCEscapeAction | read-write | current | The modem's action upon successfully recognizing the 'escape to command mode' character sequence. |
| 1.3.6.1.2.1.38.1.1.7.1.5 | ColumnmdmCCCallDuration | read-only | current | Present or last completed connection time in seconds. If there have been no previous connections, this value should be -1. |
| 1.3.6.1.2.1.38.1.1.7.1.6 | ColumnmdmCCConnectionFailReason | read-only | current | Indicates the reason that the last connection or attempt failed. The meaning of each reason code is explained below. unknown: This code means the failure reaso… |
| 1.3.6.1.2.1.38.1.1.8 | TablemdmCCStoredDialStringTable | not-accessible | current | The table of stored dial strings. |
| 1.3.6.1.2.1.38.1.1.8.1 | RowmdmCCStoredDialStringEntry | not-accessible | current | A stored dial string. |
| 1.3.6.1.2.1.38.1.1.8.1.1 | ColumnmdmCCStoredDialStringIndex | not-accessible | current | The unique index of a particular dial string. |
| 1.3.6.1.2.1.38.1.1.8.1.2 | ColumnmdmCCStoredDialString | read-write | current | A dial string stored in the modem. |
| 1.3.6.1.2.1.38.1.1.9 | TablemdmECTable | not-accessible | current | The modem error correcting table augments the modem ID table. |
| 1.3.6.1.2.1.38.1.1.9.1 | RowmdmECEntry | not-accessible | current | Entries in this table are created only by the agent. One entry exists for each modem managed by the agent. |
| 1.3.6.1.2.1.38.1.1.9.1.1 | ColumnmdmECErrorControlUsed | read-only | current | Indicates the error control method used during the current or previous call. This shall be one of the values for error control protocols registered in the capa… |
| 1.3.6.1.2.1.38.1.1.10 | TablemdmDCTable | not-accessible | current | The modem data compression table augments the modem ID table. |
| 1.3.6.1.2.1.38.1.1.10.1 | RowmdmDCEntry | not-accessible | current | Entries in this table are created only by the agent. One entry exists for each modem managed by the agent. |
| 1.3.6.1.2.1.38.1.1.10.1.1 | ColumnmdmDCCompressionTypeUsed | read-only | current | Indicates the data compression method used during the current or previous call. This shall be one of the values for compression protocols registered in the cap… |
| 1.3.6.1.2.1.38.1.1.11 | TablemdmSCTable | not-accessible | current | The modem signal convertor table augments the modem ID table. |
| 1.3.6.1.2.1.38.1.1.11.1 | RowmdmSCEntry | not-accessible | current | Entries in this table are created only by the agent. One entry exists for each modem managed by the agent. |
| 1.3.6.1.2.1.38.1.1.11.1.1 | ColumnmdmSCCurrentLineTransmitRate | read-only | current | The current link transmit rate of a connection, or the last link transmit rate of the last connection in bits per second. |
| 1.3.6.1.2.1.38.1.1.11.1.2 | ColumnmdmSCCurrentLineReceiveRate | read-only | current | The current link receive rate of a connection, or the last link receive rate of the last connection in bits per second. |
| 1.3.6.1.2.1.38.1.1.11.1.3 | ColumnmdmSCInitialLineTransmitRate | read-only | current | The initial link transmit rate of the current connection, or the initial link transmit rate of the last connection in bits per second. |
| 1.3.6.1.2.1.38.1.1.11.1.4 | ColumnmdmSCInitialLineReceiveRate | read-only | current | The initial link receive rate of the current connection, or the initial link receive rate of the last connection in bits per second. |
| 1.3.6.1.2.1.38.1.1.11.1.5 | ColumnmdmSCModulationSchemeUsed | read-only | current | The modulation scheme of the current or previous call. This shall be one of the values for modulation protocols registered in the capabilities table for this m… |
| 1.3.6.1.2.1.38.1.1.12 | TablemdmStatsTable | not-accessible | current | The modem statistics Table augments the modem ID table. |
| 1.3.6.1.2.1.38.1.1.12.1 | RowmdmStatsEntry | not-accessible | current | Entries in this table are created only by the agent. One entry exists for each modem managed by the agent. |
| 1.3.6.1.2.1.38.1.1.12.1.1 | ColumnmdmStatsRingNoAnswers | read-only | current | The number of events in which ringing was detected but the call was not answered. |
| 1.3.6.1.2.1.38.1.1.12.1.2 | ColumnmdmStatsIncomingConnectionFailures | read-only | current | The number of incoming connection requests that this modem answered in which it could not train with the other DCE. |
| 1.3.6.1.2.1.38.1.1.12.1.3 | ColumnmdmStatsIncomingConnectionCompletions | read-only | current | The number of incoming connection requests that this modem answered and successfully trained with the other DCE. |
| 1.3.6.1.2.1.38.1.1.12.1.4 | ColumnmdmStatsFailedDialAttempts | read-only | current | The number of call attempts that failed because the modem didn't go off hook, or there was no dialtone. |
| 1.3.6.1.2.1.38.1.1.12.1.5 | ColumnmdmStatsOutgoingConnectionFailures | read-only | current | The number of outgoing calls from this modem which sucessfully went off hook and dialed, in which it could not train with the other DCE. |
| 1.3.6.1.2.1.38.1.1.12.1.6 | ColumnmdmStatsOutgoingConnectionCompletions | read-only | current | The number of outgoing calls from this modem which resulted in successfully training with the other DCE. |
| 1.3.6.1.2.1.38.1.1.12.1.7 | ColumnmdmStatsRetrains | read-only | current | The number of retrains experienced on connections on this line. |
| 1.3.6.1.2.1.38.1.1.12.1.8 | ColumnmdmStats2400OrLessConnections | read-only | current | The number of connections initially established at a modulation speed of 2400 bits per second or less. |
| 1.3.6.1.2.1.38.1.1.12.1.9 | ColumnmdmStats2400To14400Connections | read-only | current | The number of connections initially established at a modulation speed of greater than 2400 bits per second and less than 14400 bits per second. |
| 1.3.6.1.2.1.38.1.1.12.1.10 | ColumnmdmStatsGreaterThan14400Connections | read-only | current | The number of connections initially established at a modulation speed of greater than 14400 bits per second. |
| 1.3.6.1.2.1.38.1.1.12.1.11 | ColumnmdmStatsErrorControlledConnections | read-only | current | The number of established connections using an error control protocol. |
| 1.3.6.1.2.1.38.1.1.12.1.12 | ColumnmdmStatsCompressedConnections | read-only | current | The number of established connections using a compression protocol. |
| 1.3.6.1.2.1.38.1.1.12.1.13 | ColumnmdmStatsCompressionEfficiency | read-only | current | The number of bytes transferred into the compression encoder divided by the number of bytes transferred out of the encoder, multiplied by 100 for either the cu… |
| 1.3.6.1.2.1.38.1.1.12.1.14 | ColumnmdmStatsSentOctets | read-only | current | The number of octets presented to the modem by the DTE. |
| 1.3.6.1.2.1.38.1.1.12.1.15 | ColumnmdmStatsReceivedOctets | read-only | current | The number of octets presented to the DTE by the modem. |
| 1.3.6.1.2.1.38.1.1.12.1.16 | ColumnmdmStatsSentDataFrames | read-only | current | The number of data frames sent on the line interface. If there is no frame-oriented protocol in use on the line interface, this counter shall not increment. |
| 1.3.6.1.2.1.38.1.1.12.1.17 | ColumnmdmStatsReceivedDataFrames | read-only | current | The number of data frames received on the line interface. If there is no frame-oriented protocol in use on the line interface, this counter shall not increment. |
| 1.3.6.1.2.1.38.1.1.12.1.18 | ColumnmdmStatsResentFrames | read-only | current | The number of times this modem retransmits frames on the line interface. If there is no frame-oriented protocol in use on the line interface, this counter shal… |
| 1.3.6.1.2.1.38.1.1.12.1.19 | ColumnmdmStatsErrorFrames | read-only | current | The number of block errors received on the link. If there is no frame-oriented protocol in use on the line interface, this counter shall not increment. |
| 1.3.6.1.2.1.38.1.2 | NodemdmConformance | |||
| 1.3.6.1.2.1.38.1.2.1 | NodemdmCompliances | |||
| 1.3.6.1.2.1.38.1.2.1.1 | CompliancemdmCompliance | current | The compliance statement for SNMPv2 entities which implement the modem MIB. | |
| 1.3.6.1.2.1.38.1.2.2 | NodemdmGroups | |||
| 1.3.6.1.2.1.38.1.2.2.1 | GroupmdmIDGroup | current | A collection of objects that identify the manufacturer and model information for a modem. | |
| 1.3.6.1.2.1.38.1.2.2.2 | GroupmdmLineInterfaceGroup | current | A collection of objects that describe the configuration and state of the modem's line interface. | |
| 1.3.6.1.2.1.38.1.2.2.3 | GroupmdmDTEInterfaceGroup | current | A collection of objects that describe the configuration and state of the modem's DTE interface. | |
| 1.3.6.1.2.1.38.1.2.2.4 | GroupmdmCallControlGroup | current | A collection of objects that describe the configuration of call control capabilities on the modem and the status of calls placed with this modem. | |
| 1.3.6.1.2.1.38.1.2.2.5 | GroupmdmErrorControlGroup | current | A collection of objects that describe the configuration and state of error control on a modem. | |
| 1.3.6.1.2.1.38.1.2.2.6 | GroupmdmDataCompressionGroup | current | A collection of objects that describe the configuration and state of data compression on a modem. | |
| 1.3.6.1.2.1.38.1.2.2.7 | GroupmdmSignalConvertorGroup | current | A collection of objects that describe the configuration and state of error control on a modem. | |
| 1.3.6.1.2.1.38.1.2.2.8 | GroupmdmStatisticsGroup | current | A collection of objects that describe the state of calls on this modem. |