NBS-CMMC-MIB
531 objects
MIB for representing NBS CMMC information
Imported Objects
| IF-MIB | InterfaceIndex |
| INET-ADDRESS-MIB | InetAddress InetAddressType |
| NBS-CMMCENUM-MIB | NbsCmmcEnumChassisType NbsCmmcEnumPortConnector NbsCmmcEnumSlotOperationType NbsCmmcEnumSlotType |
| NBS-MIB | nbs |
| SNMPv2-SMI | Counter32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-IDENTITY OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.629.200 | IdentitynbsCmmcMib | MIB for representing NBS CMMC information | ||
| 1.3.6.1.4.1.629.200.1 | IdentitynbsCmmcObjects | current | all MIB objects in nbsCmmc MIB. | |
| 1.3.6.1.4.1.629.200.2 | IdentitynbsCmmcSystemGrp | current | Objects systemic in scope | |
| 1.3.6.1.4.1.629.200.2.1 | ScalarnbsCmmcSysFwDescr | read-only | current | The description of the System Control Firmware. |
| 1.3.6.1.4.1.629.200.2.2 | ScalarnbsCmmcSysFwVers | read-only | current | The System Control Firmware version in the form Vmajor.minor. |
| 1.3.6.1.4.1.629.200.2.3 | ScalarnbsCmmcSysRestart | read-write | current | This object is used to reset the system. Writing a coldRestart(2), causes the SNMP Agent CPU to be hardware reset, similar to a power-on cycle. Writing a warmR… |
| 1.3.6.1.4.1.629.200.2.4 | ScalarnbsCmmcSysNumRestarts | read-only | current | Number of warmRestarts executed by the system, since the last coldRestart or power-on cycle. A warmRestart may be initiated by: - writing a warmRestart value i… |
| 1.3.6.1.4.1.629.200.2.5 | ScalarnbsCmmcSysErrUptime | read-only | current | The time (in hundredths of a second) since the last cold reset/power cycle when a fatal error occurred. This variable shows the system uptime from the last col… |
| 1.3.6.1.4.1.629.200.2.6 | ScalarnbsCmmcSysSetNvramDefaults | read-write | current | Writing the value setDefaults to this objects will re- store the defaults in the NVRAM data base. These values will take effect after a system reset. For the L… |
| 1.3.6.1.4.1.629.200.2.7 | ScalarnbsCmmcSysSelftestLevel | read-write | deprecated | NVRAM based level of the system selftest. The values are : ststNone - meaning that no selftest will be executed upon boot-up ststShort- meaning that a short se… |
| 1.3.6.1.4.1.629.200.2.8 | ScalarnbsCmmcSysCurrentTime | read-write | current | The current time, expressed as the number of seconds since 00:00 (midnight) 1 January 1900 GMT. Obtained via Time Protocol (RFC 868) or set by user. Not suppor… |
| 1.3.6.1.4.1.629.200.2.9 | ScalarnbsCmmcSysCurrentDateTime | read-only | current | The current time, derived from nbsCmmcSysCurrentTime, adjusted to Agent's local time (nbsCmmcSysTimeZone), expressed in the format 'www mm dd hh:mm:ss yyyy'. I… |
| 1.3.6.1.4.1.629.200.2.10 | TablenbsCmmcSysNvramTable | not-accessible | current | Copy of Non-Volatile RAM kept in Agent, including all settings, configurations, and names for all cards managed by this Agent. |
| 1.3.6.1.4.1.629.200.2.10.1 | RownbsCmmcSysNvramEntry | not-accessible | current | Represents a block of NVRAM |
| 1.3.6.1.4.1.629.200.2.10.1.1 | ColumnnbsCmmcSysNvramIndex | read-only | current | NVRAM Block number, starting with 1. |
| 1.3.6.1.4.1.629.200.2.10.1.2 | ColumnnbsCmmcSysNvramBlock | read-write | current | Bytes contained in this block of NVRAM. |
| 1.3.6.1.4.1.629.200.2.11 | ScalarnbsCmmcSysWriteConfig | read-write | current | This object is used to write the configuration file. If this returns supported, the SNMP Agent requires you to specifically write the configuration file. Any c… |
| 1.3.6.1.4.1.629.200.2.12 | ScalarnbsCmmcSysUpgrade | read-write | deprecated | This object allows user to initiate a transfer of firmware from the NM file system to the cards in selected slots. Before using, user should ensure the proper … |
| 1.3.6.1.4.1.629.200.2.13 | ScalarnbsCmmcSysLoginIdleTimeout | read-write | current | This object is used to control the idle logout timer. This timer is in minutes. If a user logged into the CLI has not typed anything for this number of minutes… |
| 1.3.6.1.4.1.629.200.2.14 | ScalarnbsCmmcSysDiscoveryAdmin | read-write | current | The Discovery protocol allows Linux NM cards to find each other on a single layer 2 network segment. By default it is enabled. |
| 1.3.6.1.4.1.629.200.2.15 | TablenbsCmmcSysDiscoveryHostTable | not-accessible | current | Table that contains host information found using the L2 Discovery protocol |
| 1.3.6.1.4.1.629.200.2.15.1 | RownbsCmmcSysDiscoveryHostEntry | not-accessible | current | Represents a single host found using the L2 Discovery protocol |
| 1.3.6.1.4.1.629.200.2.15.1.1 | ColumnnbsCmmcSysDiscoveryHostMACAddress | read-only | current | MAC address of discovered host |
| 1.3.6.1.4.1.629.200.2.15.1.2 | ColumnnbsCmmcSysDiscoveryHostDistance | read-only | current | How many hops from me is this host? |
| 1.3.6.1.4.1.629.200.2.15.1.3 | ColumnnbsCmmcSysDiscoveryHostIPAddress | read-only | current | IP address of discovered host |
| 1.3.6.1.4.1.629.200.2.15.1.4 | ColumnnbsCmmcSysDiscoveryHostAddressType | read-only | current | IP address type, select IPv4 or IPv6 |
| 1.3.6.1.4.1.629.200.2.15.1.5 | ColumnnbsCmmcSysDiscoveryHostAddress | read-only | current | IPv4 or IPv6 IP address of discovered host, this replaces nbsCmmcSysDiscoveryHostIPAddress |
| 1.3.6.1.4.1.629.200.2.15.1.6 | ColumnnbsCmmcSysDiscoveryHostSourceIfIndex | read-only | current | Interface index that the discovered host was found by. 0 for the local host. |
| 1.3.6.1.4.1.629.200.2.16 | ScalarnbsCmmcSysLastSetFailure | read-only | current | If the last SNMP SET was rejected, for example with SNMP Error: BadValue (SNMP Error 3), this object should explain why the SET failed. This string may be empt… |
| 1.3.6.1.4.1.629.200.2.17 | ScalarnbsCmmcSysTimeProtocol | read-write | current | Time Protocol (RFC 868) allows the managed device to synchronize its clock with a Time Server. When read, the agent will report notSupported(1) if this object … |
| 1.3.6.1.4.1.629.200.2.18 | ScalarnbsCmmcSysTimeServer | read-write | current | The IP Address of the Time Server. |
| 1.3.6.1.4.1.629.200.2.19 | TablenbsCmmcSysFirmwareTable | not-accessible | current | Table that lists firmware images loaded on NM. |
| 1.3.6.1.4.1.629.200.2.19.1 | RownbsCmmcSysFirmwareEntry | not-accessible | current | Description of a firmware image |
| 1.3.6.1.4.1.629.200.2.19.1.1 | ColumnnbsCmmcSysFirmwareIndex | read-only | current | Unique Id for this row |
| 1.3.6.1.4.1.629.200.2.19.1.2 | ColumnnbsCmmcSysFirmwareDescr | read-only | current | Description of firmware image |
| 1.3.6.1.4.1.629.200.2.19.1.3 | ColumnnbsCmmcSysFirmwareFilename | read-only | current | The filename of the firmware package. If it is in the format scheme://host/path, it refers to nbsCmmcSysFirmwareURL. |
| 1.3.6.1.4.1.629.200.2.19.1.4 | ColumnnbsCmmcSysFirmwareSize | read-only | current | The size (in bytes) of the firmware package file |
| 1.3.6.1.4.1.629.200.2.19.1.5 | ColumnnbsCmmcSysFirmwareMTime | read-only | current | The last modified time of the firmware package file itself. |
| 1.3.6.1.4.1.629.200.2.19.1.6 | ColumnnbsCmmcSysFirmwareVersion | read-only | current | The version of the firmware package |
| 1.3.6.1.4.1.629.200.2.19.1.7 | ColumnnbsCmmcSysFirmwareDate | read-only | current | The date of release of the firmware package in RFC 2822 format |
| 1.3.6.1.4.1.629.200.2.19.1.8 | ColumnnbsCmmcSysFirmwareType | read-write | current | What kind of entity this package is for. Valid rev files have type chassis(2), slot(3), or port(4). invalid(1) indicates this entry is not a valid rev file. de… |
| 1.3.6.1.4.1.629.200.2.19.1.9 | ColumnnbsCmmcSysFirmwareIDCs | read-only | current | A comma separated list of module versions supported by this firmware package |
| 1.3.6.1.4.1.629.200.2.19.1.10 | ColumnnbsCmmcSysFirmwareCksum | read-only | current | The checksum of the metadata. Used to uniquely identify this package file. Invalid package files have a zero Cksum. Not supported value: 0 |
| 1.3.6.1.4.1.629.200.2.19.1.11 | ColumnnbsCmmcSysFirmwareMd5 | read-only | current | The MD5 checksum of this firmware image. Used to verify the integrity of this package file. |
| 1.3.6.1.4.1.629.200.2.20 | ScalarnbsCmmcSysTimeZone | read-write | current | User-configurable TimeZone or offset from GMT. Should be used to indicate the time local to the managed device. If the system supports nbsCmmcSysTimeZoneTableS… |
| 1.3.6.1.4.1.629.200.2.21 | ScalarnbsCmmcSysSnmpV1 | read-write | current | This object enables or disables SNMPv1 protocol handling. |
| 1.3.6.1.4.1.629.200.2.22 | ScalarnbsCmmcSysSnmpV2c | read-write | current | This object enables or disables SNMPv2c protocol handling. |
| 1.3.6.1.4.1.629.200.2.23 | ScalarnbsCmmcSysSnmpV3 | read-write | current | This object enables or disables SNMPv3 protocol handling. |
| 1.3.6.1.4.1.629.200.2.24 | ScalarnbsCmmcSysStpAdmin | read-write | current | This object enables or disables STP protocol handling. |
| 1.3.6.1.4.1.629.200.2.25 | ScalarnbsCmmcSysLockTypes | read-write | current | If enabled, forces the system only to allow writes to slots/ports that are detected as the same type as the configured type. Use nbsCmmcSlotClearType to clear … |
| 1.3.6.1.4.1.629.200.2.26 | ScalarnbsCmmcSysSerialTerminalType | read-write | current | Name of terminal to use for the serial port, e.g. vt100, xterm, ansi. |
| 1.3.6.1.4.1.629.200.2.27 | ScalarnbsCmmcSysCrossConnect | read-write | current | For systems which have chassis/slots supporting cross-connect functionality, this object is used to reflect the operating state and clear the entire cross-conn… |
| 1.3.6.1.4.1.629.200.2.28 | ScalarnbsCmmcSysCountersState | read-write | current | This object is used to reset all counters in this device. If agent does not have this feature, this object should be notSupported(1). In order to reset all cou… |
| 1.3.6.1.4.1.629.200.2.31 | ScalarnbsCmmcSysSerialBaudRateAdmin | read-write | current | The Serial Console Baud Rate when not in SLIP Mode. Setting this object will change the serial console baud rate in the BootROM configuration. It will not take… |
| 1.3.6.1.4.1.629.200.2.32 | ScalarnbsCmmcSysSerialBaudRateOper | read-only | current | The current operational Serial Console Baud Rate when not in SLIP Mode. |
| 1.3.6.1.4.1.629.200.2.33 | ScalarnbsCmmcSysTimeServAddressType | read-write | current | The Address Type of the Time Server. |
| 1.3.6.1.4.1.629.200.2.34 | ScalarnbsCmmcSysTimeServAddress | read-write | current | The IPv4 or IPv6 Address of the Time Server. This entry replaces nbsCmmcSysTimeServer |
| 1.3.6.1.4.1.629.200.2.50 | ScalarnbsCmmcSysDiscoveryOper | read-only | current | The current operational status of the Discovery protocol. |
| 1.3.6.1.4.1.629.200.2.60 | ScalarnbsCmmcSysStpOper | read-only | current | The current operational status of the STP protocol. |
| 1.3.6.1.4.1.629.200.2.1001 | ScalarnbsCmmcSysProtoTableSize | read-only | current | The number of entries in nbsCmmcSysProtoTable. |
| 1.3.6.1.4.1.629.200.2.1002 | TablenbsCmmcSysProtoTable | not-accessible | current | A table to report supportable data transmission protocols. |
| 1.3.6.1.4.1.629.200.2.1002.1 | RownbsCmmcSysProtoEntry | not-accessible | current | Describes a particular protocol or line rate. |
| 1.3.6.1.4.1.629.200.2.1002.1.1 | ColumnnbsCmmcSysProtoIndex | read-only | current | Protocol number. |
| 1.3.6.1.4.1.629.200.2.1002.1.2 | ColumnnbsCmmcSysProtoFamily | read-only | current | Family of this protocol. The following family names must be used exactly for machine-readability: SONET T-Carrier E-Carrier Ethernet FibreChannel DigitalVideo … |
| 1.3.6.1.4.1.629.200.2.1002.1.3 | ColumnnbsCmmcSysProtoRate | read-only | current | Speeds or rates associated with this protocol. |
| 1.3.6.1.4.1.629.200.2.1003 | ScalarnbsCmmcSysTimeZoneTableSize | read-only | current | The number of entries in nbsCmmcSysTimeZoneTable. |
| 1.3.6.1.4.1.629.200.2.1004 | TablenbsCmmcSysTimeZoneTable | not-accessible | current | A table to report supportable timezones. |
| 1.3.6.1.4.1.629.200.2.1004.1 | RownbsCmmcSysTimeZoneEntry | not-accessible | current | Describes a timezone. |
| 1.3.6.1.4.1.629.200.2.1004.1.1 | ColumnnbsCmmcSysTimeZoneIndex | read-only | current | TimeZone index corresponding to a nbsCmmcSysTimeZone setting. The first entry is reserved for 'notSupported'. The next 25 entries are reserved for GMT-12 (gmtM… |
| 1.3.6.1.4.1.629.200.2.1004.1.2 | ColumnnbsCmmcSysTimeZoneName | read-only | current | Name of this timezone. |
| 1.3.6.1.4.1.629.200.2.1010 | ScalarnbsCmmcSysLoaderTableSize | read-only | current | The maximum number of concurrent loader sessions. |
| 1.3.6.1.4.1.629.200.2.1011 | TablenbsCmmcSysLoaderTable | not-accessible | current | A table to manage multiple loader (transfer from NM to blade or line card) sessions. |
| 1.3.6.1.4.1.629.200.2.1011.1 | RownbsCmmcSysLoaderEntry | not-accessible | current | Describes a particular loader session. |
| 1.3.6.1.4.1.629.200.2.1011.1.1 | ColumnnbsCmmcSysLoaderIndex | read-only | current | Agent-determined session number. |
| 1.3.6.1.4.1.629.200.2.1011.1.2 | ColumnnbsCmmcSysLoaderFileId | read-only | current | The nbsCmmcSysFirmwareIndex value corresponding to the file being loaded. |
| 1.3.6.1.4.1.629.200.2.1011.1.3 | ColumnnbsCmmcSysLoaderProgress | read-only | current | Percentage of file transferred so far. |
| 1.3.6.1.4.1.629.200.2.1011.1.4 | ColumnnbsCmmcSysLoaderStatus | read-only | current | Status of this file transfer. The value idle (1) indicates this loader session is unused. The value transferring (2) indicates this transfer is underway. The v… |
| 1.3.6.1.4.1.629.200.2.1011.1.5 | ColumnnbsCmmcSysLoaderAbort | read-write | current | This object allows users to prematurely halt this loader session. If this loader session can not be aborted, the agent will report notSupported(1). If nbsCmmcS… |
| 1.3.6.1.4.1.629.200.2.1011.1.6 | ColumnnbsCmmcSysLoaderAck | read-write | current | This object allows users to ACKnowledge the termination of this loader session. If nbsCmmcSysLoaderStatus is idle(1) or transferring(2), the agent will report … |
| 1.3.6.1.4.1.629.200.2.1011.1.7 | ColumnnbsCmmcSysLoaderFilename | read-only | current | A copy of nbsCmmcSysFirmwareFilename, for display. |
| 1.3.6.1.4.1.629.200.2.1020 | ScalarnbsCmmcSysFirmwareURL | read-write | current | Remote URL in the form: scheme://[username[:password]@]IP[:port][/path/]filename to use for the remote entry in FirmwareTable. When set, the remote URL will be… |
| 1.3.6.1.4.1.629.200.2.1021 | ScalarnbsCmmcSysFirmwareURLStatus | read-only | current | The state of the URL fetch process initiated by a write to SysFirmwareURL. Setting the Chassis or SlotFirmwareLoad object to the URL index will be rejected unl… |
| 1.3.6.1.4.1.629.200.2.3000 | ScalarnbsCmmcSysNVAreaTableSize | read-only | current | The number of non-volatile firmware flash image areas system wide |
| 1.3.6.1.4.1.629.200.2.3001 | TablenbsCmmcSysNVAreaTable | not-accessible | current | Table that lists firmware images loaded on a chassis, slot, or port. |
| 1.3.6.1.4.1.629.200.2.3001.1 | RownbsCmmcSysNVAreaEntry | not-accessible | current | Description of a firmware image |
| 1.3.6.1.4.1.629.200.2.3001.1.1 | ColumnnbsCmmcSysNVAreaIfIndex | read-only | current | Interface index in the form CCSSPPP |
| 1.3.6.1.4.1.629.200.2.3001.1.2 | ColumnnbsCmmcSysNVAreaBank | read-only | current | Number of this memory bank / storage area. Numbering must start from one, and bank numbers must be contiguous. |
| 1.3.6.1.4.1.629.200.2.3001.1.3 | ColumnnbsCmmcSysNVAreaStatus | read-only | current | invalid(1) indicates this entry is not a valid NV area. primary(2) indicates this entry is the primary NV area. The next time the hardware is reset, this image… |
| 1.3.6.1.4.1.629.200.2.3001.1.4 | ColumnnbsCmmcSysNVAreaDescr | read-only | current | Description of firmware image |
| 1.3.6.1.4.1.629.200.2.3001.1.5 | ColumnnbsCmmcSysNVAreaVersion | read-only | current | The version of the firmware package |
| 1.3.6.1.4.1.629.200.2.3001.1.6 | ColumnnbsCmmcSysNVAreaCksum | read-only | current | The checksum of the metadata. Used to uniquely identify this NV area. Invalid NV areas have a zero Cksum. Not supported value: 0 |
| 1.3.6.1.4.1.629.200.3 | IdentitynbsCmmcIpSnmpGrp | current | IP and SNMP configuration objects | |
| 1.3.6.1.4.1.629.200.3.1 | NodenbsCmmcIpCfg | |||
| 1.3.6.1.4.1.629.200.3.1.1 | ScalarnbsCmmcPrvIpAddr | read-write | deprecated | The SNMP Agent Administrative value of the IP Address for the private in-band access. This value is stored in the system NVRAM. The current operational IP Addr… |
| 1.3.6.1.4.1.629.200.3.1.2 | ScalarnbsCmmcPrvNetMask | read-write | deprecated | The SNMP Agent Administrative value of the subnet mask for the private in-band access. This value is stored in the system NVRAM. The current operational IP Adr… |
| 1.3.6.1.4.1.629.200.3.1.3 | ScalarnbsCmmcPrvBcastAddr | read-write | deprecated | The SNMP Agent Administrative value of the IP Broad- cast Address for the private in-band access. This value is stored in the system NVRAM. The current operati… |
| 1.3.6.1.4.1.629.200.3.1.4 | ScalarnbsCmmcSysIpAddr | read-write | current | The SNMP Agent Administrative value of the IP Address for the system. This value is stored in the system NVRAM. The current operational IP Adress may be obtain… |
| 1.3.6.1.4.1.629.200.3.1.5 | ScalarnbsCmmcSysNetMask | read-write | current | The SNMP Agent Administrative value of the subnet mask for the system. This value is stored in the system NVRAM. The current operational IP Adress may be obtai… |
| 1.3.6.1.4.1.629.200.3.1.6 | ScalarnbsCmmcSysBcastAddr | read-write | current | The SNMP Agent Administrative value of the IP Broadcast Address for the system. This value is stored in the system NVRAM. The current operational IP Adress may… |
| 1.3.6.1.4.1.629.200.3.1.7 | ScalarnbsCmmcSysObIpAddr | read-write | deprecated | The SNMP Agent Administrative value of the IP Address for the out-band access. This value is stored in the system NVRAM. The current operational IP Adress may … |
| 1.3.6.1.4.1.629.200.3.1.8 | ScalarnbsCmmcSysObNetMask | read-write | deprecated | The SNMP Agent Administrative value of the subnet mask for the out-band access. This value is stored in the system NVRAM. The current operational IP Adress may… |
| 1.3.6.1.4.1.629.200.3.1.9 | ScalarnbsCmmcSysObBcastAddr | read-write | deprecated | The SNMP Agent Administrative value of the IP Broadcast Address for the in-band access. This value is stored in the system NVRAM. The current operational IP Ad… |
| 1.3.6.1.4.1.629.200.3.1.10 | ScalarnbsCmmcSysDefaultGateway | read-write | current | The SNMP Agent Administrative value of the Default Gateway. This value is stored in the system NVRAM. The current operational Default Gateway IP Adress may be … |
| 1.3.6.1.4.1.629.200.3.1.11 | ScalarnbsCmmcSysAdminBootpState | read-write | current | This object indicates whether the NM should automatically retrieve its IP settings from its local network using BootP or DHCP. This setting will be stored in p… |
| 1.3.6.1.4.1.629.200.3.1.12 | ScalarnbsCmmcSysRunBootpState | read-only | current | This object indicates whether BootP or DHCP was enabled when the NM last booted. |
| 1.3.6.1.4.1.629.200.3.1.13 | ScalarnbsCmmcSysSerialLineMode | read-write | current | The mode in which the serial line is used: by the local Administrative Interface, or as a SLIP line. Note that setting this object to adminIf(1) value while in… |
| 1.3.6.1.4.1.629.200.3.1.14 | ScalarnbsCmmcSysSerialSlipBaudRate | read-write | deprecated | The Serial Line Baud Rate when in SLIP Mode. This value is stored in the system NVRAM as well as in the SNMP Agent current configuration. |
| 1.3.6.1.4.1.629.200.3.1.15 | ScalarnbsCmmcSysArpAgingTime | read-only | current | The aging time for the ARP table. |
| 1.3.6.1.4.1.629.200.3.1.16 | ScalarnbsCmmcSysMaxTelnetSessions | read-only | deprecated | The maximum number of entries in nbsCmmcSysTelnetTable. |
| 1.3.6.1.4.1.629.200.3.1.17 | TablenbsCmmcSysTelnetTable | not-accessible | deprecated | A table describing the Telnet Sessions |
| 1.3.6.1.4.1.629.200.3.1.17.1 | RownbsCmmcSysTelnetEntry | not-accessible | deprecated | Contains the information describing a Telnet Session |
| 1.3.6.1.4.1.629.200.3.1.17.1.1 | ColumnnbsCmmcSysTelnetSessionIndex | read-only | deprecated | The index in the Telnet Table for this entry. |
| 1.3.6.1.4.1.629.200.3.1.17.1.2 | ColumnnbsCmmcSysTelnetSessionStat | read-only | deprecated | This object indicates if there is any TELNET session in progress. |
| 1.3.6.1.4.1.629.200.3.1.17.1.3 | ColumnnbsCmmcSysTelnetHost | read-only | deprecated | This object indicates the remote IP host that connected to the local device. It is 0.0.0.0 if there is no active Telnet session |
| 1.3.6.1.4.1.629.200.3.1.17.1.4 | ColumnnbsCmmcSysTelnetHostPort | read-only | deprecated | This object indicates the port number of the remote IP host. |
| 1.3.6.1.4.1.629.200.3.1.17.1.5 | ColumnnbsCmmcSysTelnetLocal | read-only | deprecated | This object indicates the IP address of the local device. It is 0.0.0.0 if there is no active Telnet session |
| 1.3.6.1.4.1.629.200.3.1.17.1.6 | ColumnnbsCmmcSysTelnetLocalPort | read-only | deprecated | This object indicates the local port number. |
| 1.3.6.1.4.1.629.200.3.1.17.1.7 | ColumnnbsCmmcSysTelnetSessionId | read-only | deprecated | The internal session identifier for this entry. |
| 1.3.6.1.4.1.629.200.3.1.17.1.8 | ColumnnbsCmmcSysTelnetConnectTime | read-only | deprecated | This object indicates the length of time connected. |
| 1.3.6.1.4.1.629.200.3.1.17.1.9 | ColumnnbsCmmcSysTelnetHostAddressType | read-only | deprecated | This object indicates the remote host address type. |
| 1.3.6.1.4.1.629.200.3.1.17.1.10 | ColumnnbsCmmcSysTelnetHostAddress | read-only | deprecated | This object indicates the remote host address, IPv4 or IPv6. This field supercedes nbsCmmcSysTelnetHost |
| 1.3.6.1.4.1.629.200.3.1.17.1.11 | ColumnnbsCmmcSysTelnetLocalAddressType | read-only | deprecated | This object indicates the local host address type. |
| 1.3.6.1.4.1.629.200.3.1.17.1.12 | ColumnnbsCmmcSysTelnetLocalAddress | read-only | deprecated | This object indicates the local host address, IPv4 or IPv6. This field supercedes nbsCmmcSysTelnetLocal |
| 1.3.6.1.4.1.629.200.3.1.18 | ScalarnbsCmmcSysMaxPingSessions | read-only | deprecated | The maximum number of Ping Sessions allowed in this system. |
| 1.3.6.1.4.1.629.200.3.1.19 | TablenbsCmmcSysPingTable | not-accessible | deprecated | A table describing the Ping Sessions |
| 1.3.6.1.4.1.629.200.3.1.19.1 | RownbsCmmcSysPingEntry | not-accessible | deprecated | Contains the information describing a Ping Session |
| 1.3.6.1.4.1.629.200.3.1.19.1.1 | ColumnnbsCmmcSysPingSessionIndex | read-only | deprecated | Index in the Ping Session Table. |
| 1.3.6.1.4.1.629.200.3.1.19.1.2 | ColumnnbsCmmcSysPingSessionStat | read-write | deprecated | This object controls the activity of the PING process progress. If GET idlePing(1) shows that the ping process is idle If SET idlePing(1) stops an active ping … |
| 1.3.6.1.4.1.629.200.3.1.19.1.3 | ColumnnbsCmmcSysPingAddr | read-write | deprecated | The IP Address to which the NM device will ping. Setting this variable initiates the ping sequence. The default value is the loopback address 127.0.0.1. |
| 1.3.6.1.4.1.629.200.3.1.19.1.4 | ColumnnbsCmmcSysPingNumber | read-write | deprecated | The number of ICMP echo packets (pings) to be sent. The default value is 1. |
| 1.3.6.1.4.1.629.200.3.1.19.1.5 | ColumnnbsCmmcSysPingOwner | read-only | deprecated | If a Ping Process is active, then the value of this object shows who activated it: the Administrative Interface, the SNMP Agent or a Web Based Manager. |
| 1.3.6.1.4.1.629.200.3.1.19.1.6 | ColumnnbsCmmcSysPingRequests | read-only | deprecated | The number of ICMP echo request (pings) sent. |
| 1.3.6.1.4.1.629.200.3.1.19.1.7 | ColumnnbsCmmcSysPingResponses | read-only | deprecated | The number of ICMP echo response packets received. |
| 1.3.6.1.4.1.629.200.3.1.19.1.8 | ColumnnbsCmmcSysPingAddressType | read-write | deprecated | The IP Address to which the NM device will ping. Setting this variable initiates the ping sequence. The default value is the loopback address 127.0.0.1. |
| 1.3.6.1.4.1.629.200.3.1.19.1.9 | ColumnnbsCmmcSysPingAddress | read-write | deprecated | The IP Address to which the NM device will ping. Setting this variable initiates the ping sequence. The default value is the loopback address 127.0.0.1. Superc… |
| 1.3.6.1.4.1.629.200.3.1.20 | ScalarnbsCmmcSysTelnetServer | read-write | current | The telnet server ships disabled by default on the NM2. Not supported means that the telnet server status cannot be changed from SNMP. |
| 1.3.6.1.4.1.629.200.3.1.21 | ScalarnbsCmmcSysSshServer | read-write | current | The ssh server ships enabled by default on the NM2. Not supported means that the ssh server status cannot be changed from SNMP. |
| 1.3.6.1.4.1.629.200.3.1.22 | ScalarnbsCmmcSysIpAddrOper | read-only | current | The IP address actually being used by the Agent. The Agent's IP address may be assigned automatically by a bootp or DHCP server, or a static IP may be assigned… |
| 1.3.6.1.4.1.629.200.3.1.23 | ScalarnbsCmmcSysNetMaskOper | read-only | current | The subnet mask actually being used by the Agent. The Agent's subnet mask may be assigned automatically by a bootp or DHCP server, or may be assigned via the n… |
| 1.3.6.1.4.1.629.200.3.1.24 | ScalarnbsCmmcSysBcastAddrOper | read-only | current | The IP Broadcast address actually being used by the Agent. The Agent's IP Broadcast address may be assigned automatically by a bootp or DHCP server, or may be … |
| 1.3.6.1.4.1.629.200.3.1.25 | ScalarnbsCmmcSysDefaultGatewayOper | read-only | current | The Default Gateway actually being used by the Agent. The Agent's Default Gateway may be assigned automatically by a bootp or DHCP server, or may be assigned v… |
| 1.3.6.1.4.1.629.200.3.1.26 | ScalarnbsCmmcSysWebServer | read-write | current | The web server ships enabled by default on the NM2. Not supported means that the web server status cannot be changed from SNMP. |
| 1.3.6.1.4.1.629.200.3.1.27 | ScalarnbsCmmcSysWebPort | read-write | current | The TCP/UDP/IP port the Agent will listen on for web (HTTP) traffic when nbsCmmcSysWebServer is enabled(3). Not supported value: -1 |
| 1.3.6.1.4.1.629.200.3.1.28 | ScalarnbsCmmcSysTelnetPort | read-write | current | The TCP/IP port the Agent will listen on for Telnet traffic when nbsCmmcSysTelnetServer is enabled(3). Not supported value: -1 |
| 1.3.6.1.4.1.629.200.3.1.29 | ScalarnbsCmmcSysSshPort | read-write | current | The TCP/UDP/IP port the Agent will listen on for Secure Shell (SSH) traffic if nbsCmmcSysSshServer is enabled(3). Not supported value: -1 |
| 1.3.6.1.4.1.629.200.3.1.30 | ScalarnbsCmmcSysScpServer | read-write | current | The Secure Copy Protocol (SCP) server ships disabled by default on the NM2. This feature shares nbsCmmcSysSshPort with SSH, and will not work unless nbsCmmcSys… |
| 1.3.6.1.4.1.629.200.3.2 | NodenbsCmmcSnmpCfg | |||
| 1.3.6.1.4.1.629.200.3.2.1 | ScalarnbsCmmcSysWriteCommunity | read-write | current | The SNMP Agent Administrative value of the write community string. This value is stored in the system NVRAM. It will take effect after a system reset. The obje… |
| 1.3.6.1.4.1.629.200.3.2.2 | ScalarnbsCmmcSysReadCommunity | read-write | current | The SNMP Agent Administrative value of the read community string. This value is stored in the system NVRAM. It will take effect after a system reset |
| 1.3.6.1.4.1.629.200.3.2.3 | ScalarnbsCmmcSysTrapTblMaxSize | read-only | current | The maximum size (number of rows) allowed in the trap table |
| 1.3.6.1.4.1.629.200.3.2.4 | TablenbsCmmcSysTrapTable | not-accessible | current | A table of managers to whom will the traps generated by the SNMP agent will be sent. It represents the current operational table as well as the NVRAM saved tab… |
| 1.3.6.1.4.1.629.200.3.2.4.1 | RownbsCmmcSysTrapEntry | not-accessible | current | Contains the information necessary to generate a trap to be sent to a particular manager. The object nbsCmmcSysTrapTblEntStatus, when written is used to create… |
| 1.3.6.1.4.1.629.200.3.2.4.1.1 | ColumnnbsCmmcSysTrapTblEntIndex | read-only | current | The index of the entry/row in the trap table in the range 1 to the value of nbsCmmcSysTrapTblMaxSize. |
| 1.3.6.1.4.1.629.200.3.2.4.1.2 | ColumnnbsCmmcSysTrapTblEntStatus | read-write | current | This object is used to get/set the validity of the information contained by nbsCmmcSysTrapEntry row. Setting this object to the value invalid(1) has the effect… |
| 1.3.6.1.4.1.629.200.3.2.4.1.3 | ColumnnbsCmmcSysTrapTblEntIpAddr | read-write | current | IPv4 Address of a manager that is to receive the SNMP agent traps. This field is now read-only and is superseded CmmcSysTrapTblEntRecipient |
| 1.3.6.1.4.1.629.200.3.2.4.1.4 | ColumnnbsCmmcSysTrapTblEntComm | read-write | current | Community string used by the SNMP agent in the traps generated to this SNMP manager/receiver. |
| 1.3.6.1.4.1.629.200.3.2.4.1.5 | ColumnnbsCmmcSysTrapTblEntLevel | read-write | current | Event severity level threshold for this SNMP manager. If the event severity level is at least nbsCmmcSysTrapTblEntLevel, the SNMP agent will generate a trap to… |
| 1.3.6.1.4.1.629.200.3.2.4.1.6 | ColumnnbsCmmcSysTrapTblEntPort | read-write | current | The UDP/IP port on the Manager to which the Agent will send SNMP traps/notifications. Not supported value: -1 |
| 1.3.6.1.4.1.629.200.3.2.4.1.7 | ColumnnbsCmmcSysTrapTblEntAddressType | read-write | current | The address type of nbsCmmcSysTrapTblEntRecipient. Currently ipv4 and ipv6 are supported. |
| 1.3.6.1.4.1.629.200.3.2.4.1.8 | ColumnnbsCmmcSysTrapTblEntRecipient | read-write | current | IP Address (IPv4 or IPv6) or hostname of a manager that is to receive the SNMP agent generated traps; supersedes nbsCmmcSysTrapTblEntIpAddr |
| 1.3.6.1.4.1.629.200.3.2.11 | ScalarnbsCmmcSysEnablePowerSupplyTraps | read-write | current | Indicates whether powerSupplyAllarmOn and powerSupplyAllarmOff traps in this MIB should be generated. |
| 1.3.6.1.4.1.629.200.3.2.12 | ScalarnbsCmmcSysEnableModuleTraps | read-write | current | Indicates whether moduleUp and moduleDown traps in this MIB should be generated. |
| 1.3.6.1.4.1.629.200.3.2.13 | ScalarnbsCmmcSysEnableBridgeTraps | read-write | current | Indicates whether newRoot and topologyChange traps in the BRIDGE-MIB should be generated. |
| 1.3.6.1.4.1.629.200.3.2.14 | ScalarnbsCmmcSysEnableIpAccessTraps | read-write | current | Indicates whether IP access traps in this MIB should be generated. |
| 1.3.6.1.4.1.629.200.3.2.15 | ScalarnbsCmmcSysSnmpPortAdmin | read-write | current | The UDP/IP port the Agent will listen on for SNMP traffic after the next system restart. Not supported value: -1 |
| 1.3.6.1.4.1.629.200.3.2.16 | ScalarnbsCmmcSysSnmpPortOper | read-only | current | The UDP/IP port the Agent is listening on for SNMP traffic now. Not supported value: -1 |
| 1.3.6.1.4.1.629.200.4 | IdentitynbsCmmcTftpGrp | current | TFTP objects | |
| 1.3.6.1.4.1.629.200.4.1 | ScalarnbsCmmcSysTftpHostIP | read-write | current | This is the IP Address of the TFTP Server/Client serving the actual TFTP transfer. A TFTP transfer may mean a software/microcode/parameter/etc.. download/uploa… |
| 1.3.6.1.4.1.629.200.4.2 | ScalarnbsCmmcTftpMaxSessionNum | read-only | current | Maximum number of parallel TFTP sessions that are supported by the system |
| 1.3.6.1.4.1.629.200.4.3 | TablenbsCmmcTftpSessTable | not-accessible | current | A table that describes the active TFTP sessions |
| 1.3.6.1.4.1.629.200.4.3.1 | RownbsCmmcTftpSessEntry | not-accessible | current | Contains a description of a particular TFTP session |
| 1.3.6.1.4.1.629.200.4.3.1.1 | ColumnnbsCmmcTftpSessIndex | read-only | current | The index of the TFTP session (1..nbsCmmcTftpMaxSessionNum) |
| 1.3.6.1.4.1.629.200.4.3.1.2 | ColumnnbsCmmcTftpSessStatus | read-only | current | The status of this TFTP session |
| 1.3.6.1.4.1.629.200.4.3.1.3 | ColumnnbsCmmcTftpSessHostIp | read-write | current | This is the IP Address of the TFTP Host (Server/Client) serving the TFTP session as a source/destination. An IP address of 0.0.0.0 signifies that no setup has … |
| 1.3.6.1.4.1.629.200.4.3.1.4 | ColumnnbsCmmcTftpSessModuleId | read-write | deprecated | Deprecated. Module Id that owns this TFTP session (whose firmware/microcode/parameters/etc. are transferred |
| 1.3.6.1.4.1.629.200.4.3.1.5 | ColumnnbsCmmcTftpSessAction | read-write | current | This object is used to initiate a TFTP file transfer. If nbsCmmcTftpSessStatus is not active (4), the Agent should report the value inactive (1). The Manager m… |
| 1.3.6.1.4.1.629.200.4.3.1.6 | ColumnnbsCmmcTftpSessFileName | read-write | current | The name of the file to be transferred by this TFTP session. |
| 1.3.6.1.4.1.629.200.4.3.1.7 | ColumnnbsCmmcTftpSessFileSize | read-write | deprecated | The number of bytes in the file. Whichever side has the file being sent may report the file size here. Not supported value: -1 |
| 1.3.6.1.4.1.629.200.4.3.1.8 | ColumnnbsCmmcTftpSessProgress | read-only | deprecated | The number of bytes successfully transferred in this session. Not supported value: -1 |
| 1.3.6.1.4.1.629.200.4.3.1.9 | ColumnnbsCmmcTftpSessAddressType | read-write | current | This is the IP Address Type of the TFTP Host (Server/Client) serving the TFTP session as a source/destination. |
| 1.3.6.1.4.1.629.200.4.3.1.10 | ColumnnbsCmmcTftpSessAddress | read-write | current | This is the IPv4 or IPv6 Address of the TFTP Host (Server/Client) serving the TFTP session as a source/destination. Setting the nbsCmmcTftpSessAddress value wi… |
| 1.3.6.1.4.1.629.200.4.4 | ScalarnbsCmmcSysTftpHostAddressType | read-write | current | Address type of nbsCmmcSysTftpHostAddress. |
| 1.3.6.1.4.1.629.200.4.5 | ScalarnbsCmmcSysTftpHostAddress | read-write | current | Supercedes the previous value of nbsCmmcSysTftpHostIP; this is the IP Address of the TFTP Server/Client serving the actual TFTP transfer. A TFTP transfer may m… |
| 1.3.6.1.4.1.629.200.6 | IdentitynbsCmmcChassisGrp | current | Chassis objects | |
| 1.3.6.1.4.1.629.200.6.1 | TablenbsCmmcChassisTable | not-accessible | current | A table that describes the Chassis connected |
| 1.3.6.1.4.1.629.200.6.1.1 | RownbsCmmcChassisEntry | not-accessible | current | Contains a description of a particular Chassis |
| 1.3.6.1.4.1.629.200.6.1.1.1 | ColumnnbsCmmcChassisIndex | read-only | current | The index of the Chassis. |
| 1.3.6.1.4.1.629.200.6.1.1.2 | ColumnnbsCmmcChassisType | read-only | current | The type of Chassis. |
| 1.3.6.1.4.1.629.200.6.1.1.3 | ColumnnbsCmmcChassisModel | read-only | current | The model name of the chassis. |
| 1.3.6.1.4.1.629.200.6.1.1.4 | ColumnnbsCmmcChassisObjectId | read-only | current | Object Id of chassis. |
| 1.3.6.1.4.1.629.200.6.1.1.5 | ColumnnbsCmmcChassisNumberOfSlots | read-only | current | The number of slots in the Chassis. |
| 1.3.6.1.4.1.629.200.6.1.1.6 | ColumnnbsCmmcChassisHardwareRevision | read-only | current | The hardware revision of the chassis. |
| 1.3.6.1.4.1.629.200.6.1.1.7 | ColumnnbsCmmcChassisPS1Status | read-only | current | The status of Power Supply 1. |
| 1.3.6.1.4.1.629.200.6.1.1.8 | ColumnnbsCmmcChassisPS2Status | read-only | current | The status of Power Supply 2. |
| 1.3.6.1.4.1.629.200.6.1.1.9 | ColumnnbsCmmcChassisPS3Status | read-only | current | The status of Power Supply 3. |
| 1.3.6.1.4.1.629.200.6.1.1.10 | ColumnnbsCmmcChassisPS4Status | read-only | current | The status of Power Supply 4. |
| 1.3.6.1.4.1.629.200.6.1.1.11 | ColumnnbsCmmcChassisFan1Status | read-only | current | The status of Fan 1. |
| 1.3.6.1.4.1.629.200.6.1.1.12 | ColumnnbsCmmcChassisFan2Status | read-only | current | The status of Fan 2. |
| 1.3.6.1.4.1.629.200.6.1.1.13 | ColumnnbsCmmcChassisFan3Status | read-only | current | The status of Fan 3. |
| 1.3.6.1.4.1.629.200.6.1.1.14 | ColumnnbsCmmcChassisFan4Status | read-only | current | The status of Fan 4. |
| 1.3.6.1.4.1.629.200.6.1.1.15 | ColumnnbsCmmcChassisTemperature | read-only | current | The temperature (degrees Celsius) of the Chassis. Not supported value: 0x80000000 |
| 1.3.6.1.4.1.629.200.6.1.1.16 | ColumnnbsCmmcChassisTemperatureLimit | read-write | current | The maximum safe temperature (degrees Celsius) of the Chassis. Not supported value: 0x80000000 |
| 1.3.6.1.4.1.629.200.6.1.1.17 | ColumnnbsCmmcChassisTemperatureMin | read-write | current | The minimum safe temperature (degrees Celsius) of the Chassis. Not supported value: 0x80000000 |
| 1.3.6.1.4.1.629.200.6.1.1.18 | ColumnnbsCmmcChassisSignalStrength | read-only | deprecated | The received signal strength. |
| 1.3.6.1.4.1.629.200.6.1.1.19 | ColumnnbsCmmcChassisSignalStrengthMinimum | read-write | deprecated | The minimum recommended operational received signal strength. |
| 1.3.6.1.4.1.629.200.6.1.1.20 | ColumnnbsCmmcChassisEnableAutoReset | read-write | current | Continuously monitor slots for module changes, and reset if new board installed. Deprecated. The response to any GET should be notSupported(1). Any SET attempt… |
| 1.3.6.1.4.1.629.200.6.1.1.21 | ColumnnbsCmmcChassisEnableLinkTraps | read-write | current | When set, send trap to report change in link status, up or down. |
| 1.3.6.1.4.1.629.200.6.1.1.22 | ColumnnbsCmmcChassisEnableChassisTraps | read-write | current | When set, send trap to report chassis related events. |
| 1.3.6.1.4.1.629.200.6.1.1.23 | ColumnnbsCmmcChassisEnableLoopbackTraps | read-write | current | When set, send trap to report change in loopback configuration. |
| 1.3.6.1.4.1.629.200.6.1.1.24 | ColumnnbsCmmcChassisEnableSlotChangeTraps | read-write | current | When set, send trap to report slot change related events. |
| 1.3.6.1.4.1.629.200.6.1.1.25 | ColumnnbsCmmcChassisEnablePortTraps | read-write | current | When set, send trap to report port change related events. |
| 1.3.6.1.4.1.629.200.6.1.1.26 | ColumnnbsCmmcChassisResetAllModules | read-write | current | Continuously monitor slots for module changes, and reset if new board installed. Deprecated. The response to any GET should be notSupported(1). Any SET attempt… |
| 1.3.6.1.4.1.629.200.6.1.1.27 | ColumnnbsCmmcChassisEnableModuleSpecificTraps | read-write | current | When set, send trap to report change in specific cards conditions |
| 1.3.6.1.4.1.629.200.6.1.1.28 | ColumnnbsCmmcChassisLoopbackTimeout | read-write | current | loopback timeout in minutes, zero indicates forever |
| 1.3.6.1.4.1.629.200.6.1.1.29 | ColumnnbsCmmcChassisPortInfoBitMap | read-only | current | Deprecated. |
| 1.3.6.1.4.1.629.200.6.1.1.30 | ColumnnbsCmmcChassisSlotListBitMap | read-only | current | Deprecated. |
| 1.3.6.1.4.1.629.200.6.1.1.31 | ColumnnbsCmmcChassisNumberOfPortsBitMap | read-only | current | Deprecated. |
| 1.3.6.1.4.1.629.200.6.1.1.32 | ColumnnbsCmmcChassisName | read-write | current | The user assigned name for this chassis |
| 1.3.6.1.4.1.629.200.6.1.1.33 | ColumnnbsCmmcChassisEnableLINTraps | read-write | current | When off(2), suppresses any traps related to Link Integrity Notification. |
| 1.3.6.1.4.1.629.200.6.1.1.34 | ColumnnbsCmmcChassisEnablePortChangeTraps | read-write | current | When off(2), suppresses any traps related to removable Ports being inserted or removed. |
| 1.3.6.1.4.1.629.200.6.1.1.35 | ColumnnbsCmmcChassisEnablePortDiagsTraps | read-write | current | When off(2), suppresses any traps related to digital diagnostics being outside of safe levels. |
| 1.3.6.1.4.1.629.200.6.1.1.36 | ColumnnbsCmmcChassisFan5Status | read-only | current | The status of Fan 5. |
| 1.3.6.1.4.1.629.200.6.1.1.37 | ColumnnbsCmmcChassisFan6Status | read-only | current | The status of Fan 6. |
| 1.3.6.1.4.1.629.200.6.1.1.38 | ColumnnbsCmmcChassisFan7Status | read-only | current | The status of Fan 7. |
| 1.3.6.1.4.1.629.200.6.1.1.39 | ColumnnbsCmmcChassisFan8Status | read-only | current | The status of Fan 8. |
| 1.3.6.1.4.1.629.200.6.1.1.40 | ColumnnbsCmmcChassisEnableSwitchoverTraps | read-write | current | When on, NM can send notifications whenever a self-healing card switches traffic from an active port to its redundant standby port. When off, NM will not send … |
| 1.3.6.1.4.1.629.200.6.1.1.41 | ColumnnbsCmmcChassisCrossConnect | read-write | current | For chassis housing cross-connect blades or slots, this object is used to reflect the operating state and to clear the entire cross-connect map, including any … |
| 1.3.6.1.4.1.629.200.6.1.1.42 | ColumnnbsCmmcChassisNVAreaBanks | read-only | current | The maximum number of executable images that can be stored locally on this chassis. This number does not count any memory banks that are in a modular subcompon… |
| 1.3.6.1.4.1.629.200.6.1.1.43 | ColumnnbsCmmcChassisFirmwareCaps | read-only | current | This bitmask indicates which executable images this chassis can support. This object is mandatory for all chassis. Bit 0 is reserved. Subsequent bits refer to … |
| 1.3.6.1.4.1.629.200.6.1.1.44 | ColumnnbsCmmcChassisFirmwareLoad | read-write | current | This bitmask indicates which executable images this chassis has stored in its own NV area. This object is mandatory for all chassis. OCTET STRING bitmasks coun… |
| 1.3.6.1.4.1.629.200.6.1.1.45 | ColumnnbsCmmcChassisNVAreaAdmin | read-write | current | A SET on this object will force the corresponding nbsCmmcSysNvAreaStatus to primary, set this chassis' other memory banks to backup, and immediately load and e… |
| 1.3.6.1.4.1.629.200.6.1.1.46 | ColumnnbsCmmcChassisNVAreaOper | read-only | current | The nbsCmmcSysNVAreaBank of nbsCmmcSysNVAreaTable corresponding to the current operationally active firmware image. 0 indicates the current active image is NOT… |
| 1.3.6.1.4.1.629.200.6.1.1.47 | ColumnnbsCmmcChassisLoader | read-only | current | The nbsCmmcSysLoaderIndex of nbsCmmcSysLoaderTable corresponding to the current loading session. 0 indicates no loading session is active. |
| 1.3.6.1.4.1.629.200.6.1.1.48 | ColumnnbsCmmcChassisSerialNum | read-only | current | SerialNumber of this chassis. If this object is not supported, this string should be empty. |
| 1.3.6.1.4.1.629.200.6.1.1.49 | ColumnnbsCmmcChassisFace | read-only | current | ASCII string containing encoded summary of chassis front panel status. The encoding uses keywords and associated allowed values. Keyword:value pairs delimited … |
| 1.3.6.1.4.1.629.200.6.1.1.50 | ColumnnbsCmmcChassisCountersState | read-write | current | This object allows user to reset MAC counters on all ports in this Chassis. |
| 1.3.6.1.4.1.629.200.6.1.1.51 | ColumnnbsCmmcChassisPowerStatus | read-only | current | Indicates if the total power in the chassis is sufficient or insufficient. Insufficient means that the chassis won't work in a correct mode. |
| 1.3.6.1.4.1.629.200.6.1.1.52 | ColumnnbsCmmcChassisIfIndex | read-only | current | Mib2-like ifIndex of this chassis |
| 1.3.6.1.4.1.629.200.6.2 | ScalarnbsCmmcChassisCount | read-only | current | The number of chassis currently plugged into the system. |
| 1.3.6.1.4.1.629.200.7 | IdentitynbsCmmcSlotGrp | current | Slot/Card/Blade objects | |
| 1.3.6.1.4.1.629.200.7.1 | TablenbsCmmcSlotTable | not-accessible | current | A table that describes the Slot connected |
| 1.3.6.1.4.1.629.200.7.1.1 | RownbsCmmcSlotEntry | not-accessible | current | Contains a description of a particular Slot |
| 1.3.6.1.4.1.629.200.7.1.1.1 | ColumnnbsCmmcSlotChassisIndex | read-only | current | The index of the Chassis to the Slot is connected. |
| 1.3.6.1.4.1.629.200.7.1.1.2 | ColumnnbsCmmcSlotIndex | read-only | current | The slot index. |
| 1.3.6.1.4.1.629.200.7.1.1.3 | ColumnnbsCmmcSlotType | read-only | current | The front panel of card in the slot. |
| 1.3.6.1.4.1.629.200.7.1.1.4 | ColumnnbsCmmcSlotModel | read-only | current | Describes the model of card that is currently in the slot. |
| 1.3.6.1.4.1.629.200.7.1.1.5 | ColumnnbsCmmcSlotObjectId | read-only | current | The description of the type of card in the slot. |
| 1.3.6.1.4.1.629.200.7.1.1.6 | ColumnnbsCmmcSlotNumberOfPorts | read-only | current | Number of ports on the card. |
| 1.3.6.1.4.1.629.200.7.1.1.7 | ColumnnbsCmmcSlotHardwareRevision | read-only | current | This describes the hardware revision of the card |
| 1.3.6.1.4.1.629.200.7.1.1.8 | ColumnnbsCmmcSlotOperationType | read-write | current | Operation of card.. |
| 1.3.6.1.4.1.629.200.7.1.1.9 | ColumnnbsCmmcSlotReset | read-write | current | Current reset condition, and possible reset types. notSupported [1] - reported if feature unavailable. operating [2] - indicates normal operating status. phy [… |
| 1.3.6.1.4.1.629.200.7.1.1.10 | ColumnnbsCmmcSlotName | read-write | current | The user assigned name for this slot. |
| 1.3.6.1.4.1.629.200.7.1.1.11 | ColumnnbsCmmcSlotModuleType | read-only | current | Equivalent to nbsCmmcSlotType, except for modules that occupy more than one slot in a chassis. For such multi- slot modules, this ModuleType indicates the prod… |
| 1.3.6.1.4.1.629.200.7.1.1.12 | ColumnnbsCmmcSlotModuleSlot | read-only | current | This indicates the position of this slot within its module. For one-slot modules this value is always one (1). For multi-slot modules, this is a positive integ… |
| 1.3.6.1.4.1.629.200.7.1.1.13 | ColumnnbsCmmcSlotSwConfigurable | read-only | current | Indicates whether card is software configurable, usually based on hardware jumper/dip switch settings. If any changes to the hardware configuration are allowed… |
| 1.3.6.1.4.1.629.200.7.1.1.14 | ColumnnbsCmmcSlotConfiguration | read-write | current | Bit stream containing current configuration of slot. |
| 1.3.6.1.4.1.629.200.7.1.1.15 | ColumnnbsCmmcSlotMacAddress | read-only | current | MAC Address of this card. If this object is not supported, this string should be empty. |
| 1.3.6.1.4.1.629.200.7.1.1.16 | ColumnnbsCmmcSlotIPAddress | read-write | current | For non-NM cards which feature independent IP stacks, this is the SNMP Agent Administrative value of the IP Address for the card in this slot. |
| 1.3.6.1.4.1.629.200.7.1.1.17 | ColumnnbsCmmcSlotSubnetMask | read-write | current | For non-NM cards which feature independent IP stacks, this is the SNMP Agent Administrative value of the SubnetMask for the card in this slot. |
| 1.3.6.1.4.1.629.200.7.1.1.18 | ColumnnbsCmmcSlotBroadcastAddr | read-write | current | For non-NM cards which feature independent IP stacks, this is the SNMP Agent Administrative value of the IP Broadcast Address for the card in this slot. |
| 1.3.6.1.4.1.629.200.7.1.1.19 | ColumnnbsCmmcSlotDefGateway | read-write | current | For non-NM cards which feature independent IP stacks, this is the SNMP Agent Administrative value of the Default Gateway for the card in this slot. |
| 1.3.6.1.4.1.629.200.7.1.1.20 | ColumnnbsCmmcSlotHoming | read-write | current | This object describes the cabling topology of CO / CPE pairs. It must be supported on the Customer Premises Equipment (CPE) slots. Any card that does not utili… |
| 1.3.6.1.4.1.629.200.7.1.1.21 | ColumnnbsCmmcSlotRedundancyAdmin | read-write | current | This object is used to disable redundancy on certain cards that support the 802.3ah standard, but if supported, the preferred method is to use the object nbsCm… |
| 1.3.6.1.4.1.629.200.7.1.1.22 | ColumnnbsCmmcSlotDescr | read-only | current | Agent description of this slot. |
| 1.3.6.1.4.1.629.200.7.1.1.23 | ColumnnbsCmmcSlotUpgradable | read-only | current | This object indicates whether the card in this slot can now be reprogrammed. It should be used together with nbsCmmcSysUpgrade. Cards without reprogrammable fi… |
| 1.3.6.1.4.1.629.200.7.1.1.24 | ColumnnbsCmmcSlotCrossConnect | read-write | current | For slots supporting cross-connect functionality, this object is used to reflect the operating state and clear the entire cross-connect map for this slot. If t… |
| 1.3.6.1.4.1.629.200.7.1.1.25 | ColumnnbsCmmcSlotClearType | read-write | current | When nbsCmmcSysLockTypes is enabled, use this object to clear the configured slot type. Issue a set command with a value of clearType(3). A read of this object… |
| 1.3.6.1.4.1.629.200.7.1.1.26 | ColumnnbsCmmcSlotNVAreaBanks | read-only | current | The maximum number of executable images that can be stored locally on this module. This number does not count any memory banks that are in a modular subcompone… |
| 1.3.6.1.4.1.629.200.7.1.1.27 | ColumnnbsCmmcSlotFirmwareCaps | read-only | current | This bitmask indicates which executable images this module can support. This object is mandatory for all modules. Bit 0 is reserved. Subsequent bits refer to t… |
| 1.3.6.1.4.1.629.200.7.1.1.28 | ColumnnbsCmmcSlotFirmwareLoad | read-write | current | This bitmask indicates which executable images this module has stored in its own NV area. This object is mandatory for all modules. OCTET STRING bitmasks count… |
| 1.3.6.1.4.1.629.200.7.1.1.29 | ColumnnbsCmmcSlotNVAreaAdmin | read-write | current | A SET on this object will force the corresponding nbsCmmcSysNvAreaStatus to primary, set this module's other memory banks to backup, and immediately load and e… |
| 1.3.6.1.4.1.629.200.7.1.1.30 | ColumnnbsCmmcSlotNVAreaOper | read-only | current | The nbsCmmcSysNVAreaBank of nbsCmmcSysNVAreaTable corresponding to the current operationally active firmware image. 0 indicates the current active image is NOT… |
| 1.3.6.1.4.1.629.200.7.1.1.31 | ColumnnbsCmmcSlotLoader | read-only | current | The nbsCmmcSysLoaderIndex of nbsCmmcSysLoaderTable corresponding to the current loading session. 0 indicates no loading session is active. |
| 1.3.6.1.4.1.629.200.7.1.1.32 | ColumnnbsCmmcSlotSerialNum | read-only | current | SerialNumber of this module. If this object is not supported, this string should be empty. |
| 1.3.6.1.4.1.629.200.7.1.1.33 | ColumnnbsCmmcSlotToggleRate | read-write | current | For crossbar products. Used to indicate the approximate rate, in microseconds, at which this card should toggle its transmitters on and off. Not supported valu… |
| 1.3.6.1.4.1.629.200.7.1.1.34 | ColumnnbsCmmcSlotTemperature | read-only | current | The temperature (in degrees celsius) of this slot. Not supported value: 0x80000000 |
| 1.3.6.1.4.1.629.200.7.1.1.35 | ColumnnbsCmmcSlotCountersState | read-write | current | This object allows user to reset MAC counters on all ports. |
| 1.3.6.1.4.1.629.200.7.1.1.36 | ColumnnbsCmmcSlotRedundancyOper | read-only | current | This object reports the actual redundancy state of a card. For cards that do not support this feature, any reads of this object should get the response notSupp… |
| 1.3.6.1.4.1.629.200.7.1.1.37 | ColumnnbsCmmcSlotIfIndex | read-only | current | Mib2-like ifIndex of this slot |
| 1.3.6.1.4.1.629.200.7.1.1.38 | ColumnnbsCmmcSlotModuleStatus | read-only | current | Slots that have no card installed should be reported as empty(2). Slots where a card has been physically inserted should be reported as notReady(3) while the c… |
| 1.3.6.1.4.1.629.200.7.1.1.39 | ColumnnbsCmmcSlotManagementPort | read-only | current | This object, if set, reports the direct slot management port number. For cards that do not support this feature the response will be 0. |
| 1.3.6.1.4.1.629.200.7.1.1.40 | ColumnnbsCmmcSlotTemperatureLimit | read-write | current | The maximum safe temperature (degrees Celsius) of the Slot. Not supported value: 0x80000000 |
| 1.3.6.1.4.1.629.200.7.1.1.41 | ColumnnbsCmmcSlotTemperatureMin | read-write | current | The minimum safe temperature (degrees Celsius) of the Slot. Not supported value: 0x80000000 |
| 1.3.6.1.4.1.629.200.7.2 | TablenbsCmmcLedTable | not-accessible | current | A table to report status of front panel LEDs |
| 1.3.6.1.4.1.629.200.7.2.1 | RownbsCmmcLedEntry | not-accessible | current | Indicates status of a particular LED |
| 1.3.6.1.4.1.629.200.7.2.1.1 | ColumnnbsCmmcLedChassisIndex | read-only | current | The index of the Chassis to the Slot is connected. |
| 1.3.6.1.4.1.629.200.7.2.1.2 | ColumnnbsCmmcLedSlotIndex | read-only | current | The slot index. |
| 1.3.6.1.4.1.629.200.7.2.1.3 | ColumnnbsCmmcLedIndex | read-only | current | The index of the led. Index starts at 1. |
| 1.3.6.1.4.1.629.200.7.2.1.4 | ColumnnbsCmmcLedColor | read-only | current | Actual/current color of the LED. |
| 1.3.6.1.4.1.629.200.7.2.1.5 | ColumnnbsCmmcLedDescription | read-only | current | LED's label as on card and short description |
| 1.3.6.1.4.1.629.200.7.3 | TablenbsCmmcSlotFaceTable | not-accessible | current | A table that describes the front panel state of each slot |
| 1.3.6.1.4.1.629.200.7.3.1 | RownbsCmmcSlotFaceEntry | not-accessible | current | Contains a description of a particular Slot |
| 1.3.6.1.4.1.629.200.7.3.1.1 | ColumnnbsCmmcSlotFaceChassisIndex | read-only | current | The index of the Chassis housing this slot. |
| 1.3.6.1.4.1.629.200.7.3.1.2 | ColumnnbsCmmcSlotFaceSlotIndex | read-only | current | The slot index. |
| 1.3.6.1.4.1.629.200.7.3.1.3 | ColumnnbsCmmcSlotFaceRowIndex | read-only | current | Row Number |
| 1.3.6.1.4.1.629.200.7.3.1.4 | ColumnnbsCmmcSlotFaceSummary | read-only | current | ASCII string containing encoded summary of slot front panel status. The encoding uses keywords and associated allowed values. Keyword:value pairs delimited by … |
| 1.3.6.1.4.1.629.200.8 | IdentitynbsCmmcPortGrp | current | Port objects | |
| 1.3.6.1.4.1.629.200.8.1 | TablenbsCmmcPortTable | not-accessible | current | A table that describes the Port connected |
| 1.3.6.1.4.1.629.200.8.1.1 | RownbsCmmcPortEntry | not-accessible | current | Contains a description of a particular Port. |
| 1.3.6.1.4.1.629.200.8.1.1.1 | ColumnnbsCmmcPortChassisIndex | read-only | current | The index of the Chassis for the Slot to which this port is connected. |
| 1.3.6.1.4.1.629.200.8.1.1.2 | ColumnnbsCmmcPortSlotIndex | read-only | current | The index of the Slot in the Chassis to which this port is connected. |
| 1.3.6.1.4.1.629.200.8.1.1.3 | ColumnnbsCmmcPortIndex | read-only | current | The index of the Port in the Slot in the Chassis to which this port is connected. |
| 1.3.6.1.4.1.629.200.8.1.1.4 | ColumnnbsCmmcPortType | read-only | current | The physical type of port. Valid port types are > 1. The mib representation of pluggable port types are documented in nbsSffMsaIdentifier from NBS-SFF-MIB, and… |
| 1.3.6.1.4.1.629.200.8.1.1.5 | ColumnnbsCmmcPortObjectId | read-only | current | Object Id of the port |
| 1.3.6.1.4.1.629.200.8.1.1.6 | ColumnnbsCmmcPortLink | read-only | current | The link status of the port. |
| 1.3.6.1.4.1.629.200.8.1.1.7 | ColumnnbsCmmcPortAutoNegotiation | read-write | current | The AutoNegotiation status of a port. AutoNegotiation may affect the port's speed, duplex, and MDI/MDIX. If this port does not offer this feature, Agent should… |
| 1.3.6.1.4.1.629.200.8.1.1.8 | ColumnnbsCmmcPortDuplex | read-write | current | The duplex mode of the port. |
| 1.3.6.1.4.1.629.200.8.1.1.9 | ColumnnbsCmmcPortSpeed | read-write | current | The line speed of the port. This object is superseded by nbsCmmcPortProtoAdmin and nbsCmmcPortProtoOper. |
| 1.3.6.1.4.1.629.200.8.1.1.10 | ColumnnbsCmmcPortRxActivity | read-only | current | The receive status of the port. |
| 1.3.6.1.4.1.629.200.8.1.1.11 | ColumnnbsCmmcPortTxActivity | read-only | current | The transmit status of the port. |
| 1.3.6.1.4.1.629.200.8.1.1.12 | ColumnnbsCmmcPortCollisionActivity | read-only | current | The collision status of the port. |
| 1.3.6.1.4.1.629.200.8.1.1.13 | ColumnnbsCmmcPortLoopback | read-write | current | The loopback status of the port. |
| 1.3.6.1.4.1.629.200.8.1.1.14 | ColumnnbsCmmcPortEnableAdmin | read-write | current | Administratively desired operational status of the port. For the actual operational status, please see the related object nbsCmmcPortEnableOper. The value notS… |
| 1.3.6.1.4.1.629.200.8.1.1.15 | ColumnnbsCmmcPortSelectLink | read-write | current | For ports in self-healing redundant groups, this object describes this port's redundant state. The value notSupported(1) indicates this object is unused for th… |
| 1.3.6.1.4.1.629.200.8.1.1.16 | ColumnnbsCmmcPortLIN | read-write | current | Line integrity check on or off. |
| 1.3.6.1.4.1.629.200.8.1.1.17 | ColumnnbsCmmcPortAging | read-write | current | Aging on or off. |
| 1.3.6.1.4.1.629.200.8.1.1.18 | ColumnnbsCmmcPortMaxPacketSize | read-write | current | The Maximum Packet Size Allowed. |
| 1.3.6.1.4.1.629.200.8.1.1.19 | ColumnnbsCmmcPortRemoteLoopback | read-write | current | Indicates whether port should perform Remote Loopback. When on (3), outbound traffic is returned to the ingress port. In other words, traffic comes from one of… |
| 1.3.6.1.4.1.629.200.8.1.1.20 | ColumnnbsCmmcPortErrorActivity | read-only | current | The error activity of the port. |
| 1.3.6.1.4.1.629.200.8.1.1.21 | ColumnnbsCmmcPortName | read-write | current | The user assigned name for this port. This object is also used for the MIB2 object ifAlias. |
| 1.3.6.1.4.1.629.200.8.1.1.22 | ColumnnbsCmmcPortValue | read-only | current | Originally named nbsCmmcPortOpticalPower. Now usage may vary by card. For card 162, PortValue measures the Optical Power, or signal strength. For card 197, Por… |
| 1.3.6.1.4.1.629.200.8.1.1.23 | ColumnnbsCmmcPortThreshold | read-write | current | Port Threshold - usage may be different for each card. For card 197, this indicates the minimum signal strength. Value ranges from -5 to -40 decibels. For card… |
| 1.3.6.1.4.1.629.200.8.1.1.24 | ColumnnbsCmmcPortThresholdAction | read-write | current | Action to perform if threshold is crossed. Usage may be different for each card. For card 197, the allowable Actions are: notSupported(1), noAction(2), sendTra… |
| 1.3.6.1.4.1.629.200.8.1.1.25 | ColumnnbsCmmcPortRMChassis | read-write | current | The nbsCmmcPortRMChassis, nbsCmmcPortRMSlot, and nbsCmmcPortRMPort objects indicate which remote port is externally cabled to this port. This nbsCmmcPortRMChas… |
| 1.3.6.1.4.1.629.200.8.1.1.26 | ColumnnbsCmmcPortRMSlot | read-write | current | The nbsCmmcPortRMChassis, nbsCmmcPortRMSlot, and nbsCmmcPortRMPort objects indicate which remote port is externally cabled to this port. This nbsCmmcPortRMSlot… |
| 1.3.6.1.4.1.629.200.8.1.1.27 | ColumnnbsCmmcPortRMPort | read-write | current | The nbsCmmcPortRMChassis, nbsCmmcPortRMSlot, and nbsCmmcPortRMPort objects indicate which remote port is externally cabled to this port. This nbsCmmcPortRMPort… |
| 1.3.6.1.4.1.629.200.8.1.1.28 | ColumnnbsCmmcPortSerialNumber | read-only | current | Part Serial Number as reported by the component. Not supported value: 'N/A' |
| 1.3.6.1.4.1.629.200.8.1.1.29 | ColumnnbsCmmcPortVendorInfo | read-only | current | Vendor name as reported by the component. Not supported value: 'N/A' |
| 1.3.6.1.4.1.629.200.8.1.1.30 | ColumnnbsCmmcPortTemperature | read-only | current | The temperature (in degrees celsius) of this trans- ceiver. Not supported value: 0x80000000 |
| 1.3.6.1.4.1.629.200.8.1.1.31 | ColumnnbsCmmcPortTxPower | read-only | current | The output power (in milli dBm) of this transmitter. Not supported value: 0x80000000 |
| 1.3.6.1.4.1.629.200.8.1.1.32 | ColumnnbsCmmcPortRxPower | read-only | current | The received optical power (in milli dBm) of this receiver. Not supported value: 0x80000000 |
| 1.3.6.1.4.1.629.200.8.1.1.33 | ColumnnbsCmmcPortBiasAmps | read-only | current | The bias current (in microAmps) of this transmitter. The reserved value -1 indicates that this object is not supported. |
| 1.3.6.1.4.1.629.200.8.1.1.34 | ColumnnbsCmmcPortSupplyVolts | read-only | current | The supply voltage (in milliVolts) of this transmitter. The reserved value -1 indicates that this object is not supported. |
| 1.3.6.1.4.1.629.200.8.1.1.35 | ColumnnbsCmmcPortMedium | read-only | current | The type of physical communications medium. |
| 1.3.6.1.4.1.629.200.8.1.1.36 | ColumnnbsCmmcPortConnector | read-only | current | The type of physical connector or jack. |
| 1.3.6.1.4.1.629.200.8.1.1.37 | ColumnnbsCmmcPortWavelength | read-only | current | The output wavelength (in nanoMeters) of this transmitter. The reserved value -1 indicates that this object is not supported. This object has been superseded b… |
| 1.3.6.1.4.1.629.200.8.1.1.38 | ColumnnbsCmmcPortDigitalDiags | read-only | current | Indicates whether Digital Diagnostics are supported by this port. If they are supported, this variable indicates the worst severity level among the measured di… |
| 1.3.6.1.4.1.629.200.8.1.1.39 | ColumnnbsCmmcPortZoneIdAdmin | read-write | current | For Fibre Channel products, this will be the Agent-assigned ZoneId of the zone this port belongs to. For products which allow dynamic configuration of converte… |
| 1.3.6.1.4.1.629.200.8.1.1.40 | ColumnnbsCmmcPortNominalBitRate | read-write | current | This NominalBitRate variable exists for modules which support configurable speeds that may not be listed in PortSpeed. Here can be specified the raw bit rate d… |
| 1.3.6.1.4.1.629.200.8.1.1.41 | ColumnnbsCmmcPortModulePort | read-only | current | Similar to SlotModuleSlot. Some modules occupy more than one slot of a chassis. For such products, this variable will report the port number from the Module pe… |
| 1.3.6.1.4.1.629.200.8.1.1.42 | ColumnnbsCmmcPortPartRev | read-only | current | Part Number and Revision level as reported by the component. Not supported value: 'N/A' |
| 1.3.6.1.4.1.629.200.8.1.1.43 | ColumnnbsCmmcPortIfIndex | read-only | current | The index to the MIB-II Interface table entry which represents this port. If there is no corresponding MIB-II interface entry, this value should be 0. |
| 1.3.6.1.4.1.629.200.8.1.1.44 | ColumnnbsCmmcPortLinked | read-only | current | Simpler, one bit version of PortLink. The value no(1) means there is no signal detected or that signal is of poor quality. The value yes(2) indicates a good co… |
| 1.3.6.1.4.1.629.200.8.1.1.45 | ColumnnbsCmmcPortOperational | read-only | current | Indicates whether the port is in a state appropriate for normal data communications. The value no(1) means that the port is disabled or in an abnormal state su… |
| 1.3.6.1.4.1.629.200.8.1.1.46 | ColumnnbsCmmcPortZoneChassisAdmin | read-write | current | For crossbar products, this is the Chassis housing the port shown in nbsCmmcPortZoneId. |
| 1.3.6.1.4.1.629.200.8.1.1.47 | ColumnnbsCmmcPortZoneSlotAdmin | read-write | current | For crossbar products, this is the Slot housing the port shown in nbsCmmcPortZoneId. |
| 1.3.6.1.4.1.629.200.8.1.1.48 | ColumnnbsCmmcPortAlarmCause | read-only | current | For Pluggable ports with Digital Diagnostics. If there is currently no alarm condition, this string should be empty. Otherwise, this should display the most se… |
| 1.3.6.1.4.1.629.200.8.1.1.49 | ColumnnbsCmmcPortFlowControl | read-write | current | This object determines whether FlowControl should be used. If disabled(2), no FlowControl will be initiated by this port. Any FlowControl requests received wil… |
| 1.3.6.1.4.1.629.200.8.1.1.50 | ColumnnbsCmmcPortAutoNegAd | read-write | current | This object determines which capabilities will be advertised during auto negotiation. Each capability is represented by one bit. Set bit to 1 to advertise capa… |
| 1.3.6.1.4.1.629.200.8.1.1.51 | ColumnnbsCmmcPortAutoNegEditable | read-only | current | This object determines which AutoNegAd bits may be changed by the user. Bits set to 1 indicate user may choose whether to advertise the corresponding capabilit… |
| 1.3.6.1.4.1.629.200.8.1.1.52 | ColumnnbsCmmcPortWavelengthX | read-only | current | This objects supersedes the nbsCmmcPortWavelength object. The string format allows both whole numbers as in CWDM, or floating-point numbers as in DWDM. If ther… |
| 1.3.6.1.4.1.629.200.8.1.1.53 | ColumnnbsCmmcPortZoneIdOper | read-only | current | Operational version of nbsCmmcPortZoneIdAdmin |
| 1.3.6.1.4.1.629.200.8.1.1.54 | ColumnnbsCmmcPortZoneSlotOper | read-only | current | Operational version of nbsCmmcPortZoneSlotAdmin |
| 1.3.6.1.4.1.629.200.8.1.1.55 | ColumnnbsCmmcPortZoneChassisOper | read-only | current | Operational version of nbsCmmcPortZoneChassisAdmin |
| 1.3.6.1.4.1.629.200.8.1.1.56 | ColumnnbsCmmcPortLinkMatch | read-write | current | Some converter ports that are capable of autonegotiation (ANEG) may sometimes be between two end ports that would like to autonegotiate with each other. The Ag… |
| 1.3.6.1.4.1.629.200.8.1.1.57 | ColumnnbsCmmcPortMDIPinoutAdmin | read-write | current | Connecting twisted-pair ethernet ports originally required care in choosing either straight or crossover cables. Later, many ethernet ports added the feature t… |
| 1.3.6.1.4.1.629.200.8.1.1.58 | ColumnnbsCmmcPortMDIPinoutOper | read-only | current | This object reports the actual pinout state of an ethernet port. |
| 1.3.6.1.4.1.629.200.8.1.1.59 | ColumnnbsCmmcPortFCRecvAdmin | read-write | current | This object allows user to specify what this port should do if it receives a flow control request. This object is ignored when nbsCmmcPortFlowControl is disabl… |
| 1.3.6.1.4.1.629.200.8.1.1.60 | ColumnnbsCmmcPortFCRecvOper | read-only | current | This object indicates what this port will do with flow control requests it receives. |
| 1.3.6.1.4.1.629.200.8.1.1.61 | ColumnnbsCmmcPortFCSendAdmin | read-write | current | This object specifies whether this port will send flow control requests when its in danger of dropping incoming packets. This object is ignored when nbsCmmcPor… |
| 1.3.6.1.4.1.629.200.8.1.1.62 | ColumnnbsCmmcPortFCSendOper | read-only | current | This object is ignored when nbsCmmcPortFlowControl is disabled. This object indicates whether or not this port will send flow control requests. If it does, the… |
| 1.3.6.1.4.1.629.200.8.1.1.63 | ColumnnbsCmmcPortAutoNegWait | read-write | current | Sets the number of seconds a port should autonegotiate [ANEG] before deciding a link is down. This object is used by the NM when LIN and ANEG are both enabled.… |
| 1.3.6.1.4.1.629.200.8.1.1.64 | ColumnnbsCmmcPortTemperatureLevel | read-only | current | This object indicates whether this port has a temperature problem. If this port does not support SFF-8472 Digital Diagnostics, this value should be notSupporte… |
| 1.3.6.1.4.1.629.200.8.1.1.65 | ColumnnbsCmmcPortTxPowerLevel | read-only | current | This object indicates whether this port has a problem with its transmitter power. If this port does not support SFF-8472 Digital Diagnostics, this value should… |
| 1.3.6.1.4.1.629.200.8.1.1.66 | ColumnnbsCmmcPortRxPowerLevel | read-only | current | This object indicates whether this port has a problem with the power of its received signal. If this port does not support SFF-8472 Digital Diagnostics, this v… |
| 1.3.6.1.4.1.629.200.8.1.1.67 | ColumnnbsCmmcPortBiasAmpsLevel | read-only | current | This object indicates whether this port has a problem with the electric current going through the port. If this port does not support SFF-8472 Digital Diagnost… |
| 1.3.6.1.4.1.629.200.8.1.1.68 | ColumnnbsCmmcPortSupplyVoltsLevel | read-only | current | This object indicates whether this port has a problem with the electric voltage across the port. If this port does not support SFF-8472 Digital Diagnostics, th… |
| 1.3.6.1.4.1.629.200.8.1.1.69 | ColumnnbsCmmcPortAmpGainOper | read-only | current | The current actual operational gain (in milli dB) of an optical amplifier. For nbsCmmcSlotType 503, this object only applies to AGC mode. The reserved value -1… |
| 1.3.6.1.4.1.629.200.8.1.1.70 | ColumnnbsCmmcPortAmpGainAdmin | read-write | current | The user configured administrative gain (in milli dB) of an optical amplifier. For nbsCmmcSlotType 503, this object only applies to AGC mode. The reserved valu… |
| 1.3.6.1.4.1.629.200.8.1.1.71 | ColumnnbsCmmcPortAmpOutputPwrAdmin | read-write | current | The user configured desired output power (in milli dBm) of an optical amplifier. For nbsCmmcSlotType 503, this object only applies to APC mode. Not supported v… |
| 1.3.6.1.4.1.629.200.8.1.1.72 | ColumnnbsCmmcPortProtoCapabilities | read-only | current | This bitmask indicates which protocols this port can support. This object is mandatory for all ports in systems where the nbsCmmcSysProtoTable is supported. Bi… |
| 1.3.6.1.4.1.629.200.8.1.1.73 | ColumnnbsCmmcPortProtoAdmin | read-write | current | The nbsCmmcSysProtoIndex of nbsCmmcSysProtoTable corresponding to the administratively desired family and rate of this port's protocol. The value 0 is reserved… |
| 1.3.6.1.4.1.629.200.8.1.1.74 | ColumnnbsCmmcPortProtoOper | read-only | current | The nbsCmmcSysProtoIndex of nbsCmmcSysProtoTable corresponding to the current operational family and rate of this port's protocol. The value 1 is reserved for … |
| 1.3.6.1.4.1.629.200.8.1.1.75 | ColumnnbsCmmcPortPreambleLen | read-write | current | Defines the length of the transmitted ethernet preamble for every frame on this port. The value standard(2) indicates the standard 8 byte ethernet preamble sho… |
| 1.3.6.1.4.1.629.200.8.1.1.76 | ColumnnbsCmmcPortPreferred | read-write | current | Among a group of ports this object per port says whether this ports is preferred or not. A preferred port in a redundant group (usually a pair of ports) will a… |
| 1.3.6.1.4.1.629.200.8.1.1.77 | ColumnnbsCmmcPortCableLen | read-write | current | This object is used to specify the expected maximum cable length for copper DSX ports such as T1, E1, and T3. If a port does not use this feature, this object … |
| 1.3.6.1.4.1.629.200.8.1.1.78 | ColumnnbsCmmcPortRedundantTxMode | read-write | current | This object determines whether or not a redundant port's transmitter should be shut down when that port is on standby. If both redundant ports are connected (v… |
| 1.3.6.1.4.1.629.200.8.1.1.79 | ColumnnbsCmmcPortTermination | read-write | current | Administrative setting for the line termination impedance of the port. The value disable (2) indicates that the line is to be terminated elsewhere. |
| 1.3.6.1.4.1.629.200.8.1.1.80 | ColumnnbsCmmcPortDescription | read-only | current | A functional description of this port. May include port's role in the module, connector type, and other relevant info. |
| 1.3.6.1.4.1.629.200.8.1.1.81 | ColumnnbsCmmcPortTransmitUnmapped | read-write | current | This object is for crossbar products. It allows the user to choose whether this port's transmitter should be enabled or disabled when this port is not mapped t… |
| 1.3.6.1.4.1.629.200.8.1.1.82 | ColumnnbsCmmcPortToggleMode | read-write | current | This object allows to the user to toggle the transmitter of this port. The value enabled(3) causes the transmitter to blink on and off at the rate specified in… |
| 1.3.6.1.4.1.629.200.8.1.1.83 | ColumnnbsCmmcPortCrossConnect | read-write | current | For ports supporting cross-connect functionality, this object is used to reflect the operating state and clear this port from all cross-connect maps. If the po… |
| 1.3.6.1.4.1.629.200.8.1.1.84 | ColumnnbsCmmcPortZoneIfIndexAdmin | read-write | current | Mib2 ifIndex of desired crossbar partner. Zero (0) indicates this port should be unmapped. |
| 1.3.6.1.4.1.629.200.8.1.1.85 | ColumnnbsCmmcPortZoneIfIndexOper | read-only | current | Mib2 ifIndex of actual crossbar partner. Zero (0) indicates this port is currently unmapped. |
| 1.3.6.1.4.1.629.200.8.1.1.86 | ColumnnbsCmmcPortEnableOper | read-only | current | Actual current operational status of the port. This object is related to the nbsCmmcPortEnableAdmin object, where users specify the administrative operational … |
| 1.3.6.1.4.1.629.200.8.1.1.87 | ColumnnbsCmmcPortMappingType | read-write | current | Administrative crossbar mapping restrictions for this port. Non-crossbar ports must be reported as notSupported(1). If notSupported, any SET attempts will be r… |
| 1.3.6.1.4.1.629.200.8.1.1.88 | ColumnnbsCmmcPortCountersState | read-write | current | This object allows user to reset MAC counters for this port. |
| 1.3.6.1.4.1.629.200.8.1.1.89 | ColumnnbsCmmcPortAmpGainMinimum | read-only | current | This object indicates (in millidecibels) the smallest gain user can set. |
| 1.3.6.1.4.1.629.200.8.1.1.90 | ColumnnbsCmmcPortAmpGainMaximum | read-only | current | This object indicates (in millidecibels) the largest gain user can set. |
| 1.3.6.1.4.1.629.200.8.1.1.91 | ColumnnbsCmmcPortAmpGainStepSize | read-only | current | Resolution (in millidecibels) of amplifier. Indicates the increment between amplifier gain settings. |
| 1.3.6.1.4.1.629.200.8.1.1.92 | ColumnnbsCmmcPortSniffer | read-write | current | Sniffing on or off. |
| 1.3.6.1.4.1.629.200.8.1.1.93 | ColumnnbsCmmcPortExternalLink1 | read-write | current | Equivalent to the nbsCmmcPortRMChassis, nbsCmmcPortRMSlot, and nbsCmmcPortRMPort triplet. Set to 0 to indicate this port has no associated intra-node or inter-… |
| 1.3.6.1.4.1.629.200.8.1.1.94 | ColumnnbsCmmcPortExternalLink2 | read-write | current | For y-cable implementations - set by the user to indicate the second intra-node endpoint of a y-cable. Set to 0 to indicate this port has no associated intra-n… |
| 1.3.6.1.4.1.629.200.8.1.1.95 | ColumnnbsCmmcPortNVAreaBanks | read-only | current | The maximum number of executable images that can be stored locally on this module. This number does not count any memory banks that are in a modular subcompone… |
| 1.3.6.1.4.1.629.200.8.1.1.96 | ColumnnbsCmmcPortFirmwareCaps | read-only | current | This bitmask indicates which executable images this module can support. This object is mandatory for all modules. Bit 0 is reserved. Subsequent bits refer to t… |
| 1.3.6.1.4.1.629.200.8.1.1.97 | ColumnnbsCmmcPortFirmwareLoad | read-write | current | This bitmask indicates which executable images this module has stored in its own NV area. This object is mandatory for all modules. OCTET STRING bitmasks count… |
| 1.3.6.1.4.1.629.200.8.1.1.98 | ColumnnbsCmmcPortNVAreaAdmin | read-write | current | A SET on this object will force the corresponding nbsCmmcSysNvAreaStatus to primary, set this module's other memory banks to backup, and immediately load and e… |
| 1.3.6.1.4.1.629.200.8.1.1.99 | ColumnnbsCmmcPortNVAreaOper | read-only | current | The nbsCmmcSysNVAreaBank of nbsCmmcSysNVAreaTable corresponding to the current operationally active firmware image. 0 indicates the current active image is NOT… |
| 1.3.6.1.4.1.629.200.8.1.1.100 | ColumnnbsCmmcPortLoader | read-only | current | The nbsCmmcSysLoaderIndex of nbsCmmcSysLoaderTable corresponding to the current loading session. 0 indicates no loading session is active. |
| 1.3.6.1.4.1.629.200.9 | IdentitynbsCmmcNtpGrp | current | NTP objects | |
| 1.3.6.1.4.1.629.200.10 | IdentitynbsCmmcSmtpGrp | current | SMTP objects | |
| 1.3.6.1.4.1.629.200.10.1 | ScalarnbsCmmcSmtpDomainName | read-write | deprecated | This entry contains the device's domain name. For example myDomain.com. It is used to identify the sender's domain. |
| 1.3.6.1.4.1.629.200.10.2 | ScalarnbsCmmcSmtpServerAddress | read-write | deprecated | Entry containing SMTP server's IP address. |
| 1.3.6.1.4.1.629.200.10.3 | ScalarnbsCmmcSmtpRcvrLevel | read-only | deprecated | Event severity level threshold for this SMTP receiver. If the event severity level is at least nbsCmmcSmtpRcvrLevel. the SNMP agent will generate an e-mail to … |
| 1.3.6.1.4.1.629.200.10.4 | ScalarnbsCmmcSmtpRcvrNum | read-only | deprecated | Maximum number of SMTP receivers in nbsCmmcSmtpRcvrTable. |
| 1.3.6.1.4.1.629.200.10.5 | TablenbsCmmcSmtpRcvrTable | not-accessible | deprecated | A list of SMTP receivers entries. |
| 1.3.6.1.4.1.629.200.10.5.1 | RownbsCmmcSmtpRcvrEntry | not-accessible | deprecated | Entry containing SMTP information for a particular receiver entry. |
| 1.3.6.1.4.1.629.200.10.5.1.1 | ColumnnbsCmmcSmtpRcvrIndex | read-only | deprecated | The Email Recipient Index |
| 1.3.6.1.4.1.629.200.10.5.1.2 | ColumnnbsCmmcSmtpRcvrEmailAddress | read-write | deprecated | Entry containing SMTP receiver's domain name (email address). The default is the device's domain name, if set. |
| 1.3.6.1.4.1.629.200.10.5.1.3 | ColumnnbsCmmcSmtpRcvrStatus | read-write | deprecated | To add a new entry to the nbsCmmcSmtpRcvrTable, set this object to valid(2) for an IP address which is not already in the table. To remove an entry from the ta… |
| 1.3.6.1.4.1.629.200.11 | IdentitynbsCmmcSysLogGrp | current | SysLog objects | |
| 1.3.6.1.4.1.629.200.11.1 | ScalarnbsCmmcSysLogRunningLevel | read-write | current | Indicates the level at which the system log message handler saves to a running message log. The level disabled(1) instructs the Agent to log nothing. This leve… |
| 1.3.6.1.4.1.629.200.11.2 | ScalarnbsCmmcSysLogNvLevel | read-write | current | Indicates the level at which the system log message handler saves in a non-volatile media(NVRAM,FLASH,etc.). For descriptions of each level, please see the DES… |
| 1.3.6.1.4.1.629.200.11.3 | ScalarnbsCmmcSysLogTrapLevel | read-write | current | Indicates the level at which the system log message handler should generate a trap or SNMP notification. For descriptions of each level, please see the DESCRIP… |
| 1.3.6.1.4.1.629.200.11.4 | ScalarnbsCmmcSysLogEmailLevel | read-write | current | Indicates the level at which the system log message handler should generate an email message. For descriptions of each level, please see the DESCRIPTION for nb… |
| 1.3.6.1.4.1.629.200.11.5 | TablenbsCmmcSysLogMessageTable | not-accessible | current | This table defines a severity level for each type of message/event generated by the system. |
| 1.3.6.1.4.1.629.200.11.5.1 | RownbsCmmcSysLogMessageEntry | not-accessible | current | A system log message control table entry. |
| 1.3.6.1.4.1.629.200.11.5.1.1 | ColumnnbsCmmcSysLogMessageType | read-only | current | System log message type. |
| 1.3.6.1.4.1.629.200.11.5.1.2 | ColumnnbsCmmcSysLogMessageSeverity | read-only | current | System log message severity. |
| 1.3.6.1.4.1.629.200.11.6 | ScalarnbsCmmcSysRunningLogMessageTotal | read-only | current | Total number of messages in Running log table. |
| 1.3.6.1.4.1.629.200.11.7 | TablenbsCmmcSysRunningLogMessageTable | not-accessible | current | A table that describes the logged messages |
| 1.3.6.1.4.1.629.200.11.7.1 | RownbsCmmcSysRunningLogMessageEntry | not-accessible | current | Contains a description of a particular message entry |
| 1.3.6.1.4.1.629.200.11.7.1.1 | ColumnnbsCmmcSysRunningLogMessageIndex | read-only | current | The index of the message entry. |
| 1.3.6.1.4.1.629.200.11.7.1.2 | ColumnnbsCmmcSysRunningLogMessageSeverity | read-only | current | The importance of this event. |
| 1.3.6.1.4.1.629.200.11.7.1.3 | ColumnnbsCmmcSysRunningLogMessageErrorID | read-only | current | Error code of the message. |
| 1.3.6.1.4.1.629.200.11.7.1.4 | ColumnnbsCmmcSysRunningLogMessageSession | read-only | current | Module Id of session causing the event. |
| 1.3.6.1.4.1.629.200.11.7.1.5 | ColumnnbsCmmcSysRunningLogMessageTime | read-only | current | Time of occurrence of the event. |
| 1.3.6.1.4.1.629.200.11.7.1.6 | ColumnnbsCmmcSysRunningLogMessageModule | read-only | current | The name of the module causing the event. |
| 1.3.6.1.4.1.629.200.11.7.1.7 | ColumnnbsCmmcSysRunningLogMessageString | read-only | current | The actual event message. |
| 1.3.6.1.4.1.629.200.11.8 | ScalarnbsCmmcSysNvramLogMessageTotal | read-only | current | Total number of messages in Nvram log table. |
| 1.3.6.1.4.1.629.200.11.9 | TablenbsCmmcSysNvramLogMessageTable | not-accessible | current | A table that describes the logged messages |
| 1.3.6.1.4.1.629.200.11.9.1 | RownbsCmmcSysNvramLogMessageEntry | not-accessible | current | Contains a description of a particular message entry |
| 1.3.6.1.4.1.629.200.11.9.1.1 | ColumnnbsCmmcSysNvramLogMessageIndex | read-only | current | The index of the message entry. |
| 1.3.6.1.4.1.629.200.11.9.1.2 | ColumnnbsCmmcSysNvramLogMessageSeverity | read-only | current | Severity of the error. |
| 1.3.6.1.4.1.629.200.11.9.1.3 | ColumnnbsCmmcSysNvramLogMessageErrorID | read-only | current | Error code of the message. |
| 1.3.6.1.4.1.629.200.11.9.1.4 | ColumnnbsCmmcSysNvramLogMessageSession | read-only | current | Module Id of session causing the error. |
| 1.3.6.1.4.1.629.200.11.9.1.5 | ColumnnbsCmmcSysNvramLogMessageTime | read-only | current | Value of MIB-II sysUpTime (RFC 1213) at the time the error occurred. Note that sysUpTime resets to zero each time the agent is restarted. |
| 1.3.6.1.4.1.629.200.11.9.1.6 | ColumnnbsCmmcSysNvramLogMessageModule | read-only | current | The name of the module causing the error. |
| 1.3.6.1.4.1.629.200.11.9.1.7 | ColumnnbsCmmcSysNvramLogMessageString | read-only | current | The actual error message. |
| 1.3.6.1.4.1.629.200.11.9.1.8 | ColumnnbsCmmcSysNvramLogMessagePTime | read-only | current | The nbsCmmcSysCurrentTime at the moment this entry was made. This timestamp is derived from the Time Protocol (RFC 868), so it is independent of the system's U… |
| 1.3.6.1.4.1.629.200.11.9.1.9 | ColumnnbsCmmcSysNvramLogMessageDateTime | read-only | current | The nbsCmmcSysCurrentDateTime at the moment this entry was made. This timestamp is derived from nbsCmmcSysNvramLogMessagePTime, so it is independent of the sys… |
| 1.3.6.1.4.1.629.200.11.10 | ScalarnbsCmmcSysAuditLogTotal | read-only | current | The number of entries in the audit log. |
| 1.3.6.1.4.1.629.200.11.11 | TablenbsCmmcSysAuditLogTable | not-accessible | current | User activity log. |
| 1.3.6.1.4.1.629.200.11.11.1 | RownbsCmmcSysAuditLogEntry | not-accessible | current | Contains a description of a particular message entry |
| 1.3.6.1.4.1.629.200.11.11.1.1 | ColumnnbsCmmcSysAuditLogIndex | read-only | current | The index of the message entry. |
| 1.3.6.1.4.1.629.200.11.11.1.2 | ColumnnbsCmmcSysAuditLogUpTime | read-only | current | Value of MIB-II sysUpTime (RFC 1213) at the time the error occurred. Note that sysUpTime resets to zero each time the agent is restarted. |
| 1.3.6.1.4.1.629.200.11.11.1.3 | ColumnnbsCmmcSysAuditLogDateTime | read-only | current | The nbsCmmcSysCurrentDateTime at the moment this entry was made. This timestamp is independent of the system's UpTime. |
| 1.3.6.1.4.1.629.200.11.11.1.4 | ColumnnbsCmmcSysAuditLogString | read-only | current | Log entry. Usually username:login or username:logout |
| 1.3.6.1.4.1.629.200.11.12 | ScalarnbsCmmcSysLogRemoteServer | read-write | current | The IP address that rsyslog messages should be sent to. |
| 1.3.6.1.4.1.629.200.11.13 | ScalarnbsCmmcSysLogRemoteLevel | read-write | current | Indicates the level at which the system log message handler sends to remote syslog server. |
| 1.3.6.1.4.1.629.200.11.14 | ScalarnbsCmmcSysRunningLogMessageClear | read-write | current | This object is used to erase all entries from the Agent's internal Running Log. If the Agent does not support this feature, it must return the value notSupport… |
| 1.3.6.1.4.1.629.200.11.15 | ScalarnbsCmmcSysNvramLogMessageClear | read-write | current | This object is used to erase all entries from the Agent's internal NVRAM (Persistent Memory) Log. If the Agent does not support this feature, it must return th… |
| 1.3.6.1.4.1.629.200.11.16 | ScalarnbsCmmcSysAuditLogClear | read-write | current | This object is used to erase all entries from the Agent's internal Audit Log. If the Agent does not support this feature, it must return the value notSupported… |
| 1.3.6.1.4.1.629.200.11.17 | ScalarnbsCmmcSysLogNvSize | read-write | current | How large the Nvram log is allowed to be (in kilobytes). |
| 1.3.6.1.4.1.629.200.12 | IdentitynbsCmmcTrapGrp | current | Trap objects | |
| 1.3.6.1.4.1.629.200.12.1 | ScalarnbsCmmcTrapLastMessage | accessible-for-notify | current | The last message sent by the system |
| 1.3.6.1.4.1.629.200.12.2 | ScalarnbsCmmcTrapPowerSupplyId | accessible-for-notify | current | ID of the power supply |
| 1.3.6.1.4.1.629.200.12.3 | ScalarnbsCmmcTrapFanId | accessible-for-notify | current | ID of the fan |
| 1.3.6.1.4.1.629.200.12.4 | ScalarnbsCmmcTrapPortIndex | accessible-for-notify | current | Index of the Port |
| 1.3.6.1.4.1.629.200.12.5 | ScalarnbsCmmcTrapPortName | accessible-for-notify | current | Name of the Port |
| 1.3.6.1.4.1.629.200.12.6 | ScalarnbsCmmcTrapShutdownReason | accessible-for-notify | current | The reason for the last system shutdown |
| 1.3.6.1.4.1.629.200.12.7 | ScalarnbsCmmcTrapErrorInfo | accessible-for-notify | current | Brief explanation of the cause or nature of errors that triggered an nbsCmmcTrapPortErrorsDetected trap. |
| 1.3.6.1.4.1.629.200.12.10 | ScalarnbsCmmcSlotModelLocked | accessible-for-notify | current | The model of the slot's saved configuration. |
| 1.3.6.1.4.1.629.200.12.11 | ScalarnbsCmmcSlotModelInserted | accessible-for-notify | current | The model of the newly inserted module. |
| 1.3.6.1.4.1.629.200.13 | IdentitynbsCmmcTraps | current | SNMP Traps | |
| 1.3.6.1.4.1.629.200.13.0 | IdentitynbsCmmcTraps0 | current | SNMP Traps | |
| 1.3.6.1.4.1.629.200.13.0.1 | NotificationnbsCmmcTrapGenericTrap | deprecated | The last message sent by the system. | |
| 1.3.6.1.4.1.629.200.13.0.2 | NotificationnbsCmmcTrapSpecificTrap | deprecated | ********* DEPRECATED ********** As of Agent version 4.14, this trap will not be sent. | |
| 1.3.6.1.4.1.629.200.13.0.3 | NotificationnbsCmmcTrapDeviceRebooted | current | Sent after device boots up. The cause of the last shutdown is indicated in nbsCmmcTrapShutdownReason. This Notification should be of Severity FATAL. | |
| 1.3.6.1.4.1.629.200.13.0.4 | NotificationnbsCmmcTrapDeviceOnline | current | Sent when device detects restoration of network communications. ChassisIndex and SlotIndex indicate the location of the NM issuing the trap This Notification s… | |
| 1.3.6.1.4.1.629.200.13.0.5 | NotificationnbsCmmcTrapDeviceShuttingDown | current | Sent just before device shuts itself down. Reason for shutdown is indicated in nbsCmmcTrapShutdownReason. This Notification should be of Severity FATAL. | |
| 1.3.6.1.4.1.629.200.13.0.6 | NotificationnbsCmmcTrapPowerSupplyFailure | current | Unique trap for power supply failure events. This Notification should be of Severity ERROR. | |
| 1.3.6.1.4.1.629.200.13.0.7 | NotificationnbsCmmcTrapPowerSupplyRestored | current | Sent when power supply starts working again. This Notification should be of Severity ERROR. | |
| 1.3.6.1.4.1.629.200.13.0.8 | NotificationnbsCmmcTrapFanFailure | current | Unique trap for fan failure events. This Notification should be of Severity WARNING. | |
| 1.3.6.1.4.1.629.200.13.0.9 | NotificationnbsCmmcTrapFanRestored | current | Sent when fan starts working again. This Notification should be of Severity WARNING. | |
| 1.3.6.1.4.1.629.200.13.0.10 | NotificationnbsCmmcTrapChassisTempTooHigh | current | Sent when temperature rises above hottest permissible temperature. This Notification should be of Severity ERROR. | |
| 1.3.6.1.4.1.629.200.13.0.11 | NotificationnbsCmmcTrapChassisTempTooLow | current | Sent when temperature falls under coldest permissible temperature. This Notification should be of Severity ERROR. | |
| 1.3.6.1.4.1.629.200.13.0.12 | NotificationnbsCmmcTrapChassisTempOk | current | Sent when temperature returns to permissible range. This Notification should be of Severity ERROR. | |
| 1.3.6.1.4.1.629.200.13.0.13 | NotificationnbsCmmcTrapSlotModuleIn | current | Sent when card is physically inserted. This Notification should be of Severity ERROR. | |
| 1.3.6.1.4.1.629.200.13.0.14 | NotificationnbsCmmcTrapSlotModuleOut | current | Sent when card is physically removed. This Notification should be of Severity ERROR. | |
| 1.3.6.1.4.1.629.200.13.0.15 | NotificationnbsCmmcTrapPortEnabled | current | Sent after nbsCmmcPortEnableOper changes to enable(3). This Notification should be of Severity WARNING. | |
| 1.3.6.1.4.1.629.200.13.0.16 | NotificationnbsCmmcTrapPortDisabled | current | Sent after nbsCmmcPortEnableOper changes to disable(2). This Notification should be of Severity WARNING. | |
| 1.3.6.1.4.1.629.200.13.0.17 | NotificationnbsCmmcTrapPortLinkUp | current | Sent when nbsCmmcPortLink transitions from noSignal(2) to a connected state. This Notification should be of Severity ERROR. | |
| 1.3.6.1.4.1.629.200.13.0.18 | NotificationnbsCmmcTrapPortLinkDown | current | Sent when nbsCmmcPortLink transitions from a connected state to noSignal(2). This Notification should be of Severity ERROR. | |
| 1.3.6.1.4.1.629.200.13.0.19 | NotificationnbsCmmcTrapPortLINOn | current | Sent when Link Integrity Notification is turned on. This Notification should be of Severity WARNING. | |
| 1.3.6.1.4.1.629.200.13.0.20 | NotificationnbsCmmcTrapPortLINOff | current | Sent when Link Integrity Notification is turned off. This Notification should be of Severity WARNING. | |
| 1.3.6.1.4.1.629.200.13.0.21 | NotificationnbsCmmcTrapPortLoopbackOn | current | Sent when Port is set to a Loopback state. This Notification should be of Severity WARNING. | |
| 1.3.6.1.4.1.629.200.13.0.22 | NotificationnbsCmmcTrapPortLoopbackOff | current | Sent when Port returns from a Loopback state. This Notification should be of Severity WARNING. | |
| 1.3.6.1.4.1.629.200.13.0.23 | NotificationnbsCmmcTrapPortMaximumExceeded | current | Sent when PortValue exceeds PortThreshold. This Notification should be of Severity WARNING. | |
| 1.3.6.1.4.1.629.200.13.0.24 | NotificationnbsCmmcTrapPortRemoved | current | Sent when a hot-swappable port is removed. This Notification should be of Severity WARNING. | |
| 1.3.6.1.4.1.629.200.13.0.25 | NotificationnbsCmmcTrapPortInserted | current | Sent when a hot-swappable port is inserted. This Notification should be of Severity WARNING. | |
| 1.3.6.1.4.1.629.200.13.0.26 | NotificationnbsCmmcTrapPortTempTooLow | current | Sent when transmitter temperature is too cold. For SFF Digital Diagnostics, this corresponds to the low temperature alarm. This Notification should be of Sever… | |
| 1.3.6.1.4.1.629.200.13.0.27 | NotificationnbsCmmcTrapPortTempTooHigh | current | Sent when transmitter temperature is too hot. For SFF Digital Diagnostics, this corresponds to the high temperature alarm. This Notification should be of Sever… | |
| 1.3.6.1.4.1.629.200.13.0.28 | NotificationnbsCmmcTrapPortRxPowerTooLow | current | Sent when received signal is too weak. For SFF Digital Diagnostics, this corresponds to the low RX power alarm. This Notification should be of Severity ERROR. | |
| 1.3.6.1.4.1.629.200.13.0.29 | NotificationnbsCmmcTrapPortRxPowerTooHigh | current | Sent when received signal is too powerful. For SFF Digital Diagnostics, this corresponds to the high RX power alarm. This Notification should be of Severity ER… | |
| 1.3.6.1.4.1.629.200.13.0.30 | NotificationnbsCmmcTrapPortTxPowerTooLow | current | Sent when transmitter power is too weak. For SFF Digital Diagnostics, this corresponds to the low TX power alarm. This Notification should be of Severity ERROR. | |
| 1.3.6.1.4.1.629.200.13.0.31 | NotificationnbsCmmcTrapPortTxPowerTooHigh | current | Sent when transmitter power is too strong. For SFF Digital Diagnostics, this corresponds to the high TX power alarm. This Notification should be of Severity ER… | |
| 1.3.6.1.4.1.629.200.13.0.32 | NotificationnbsCmmcTrapPortAmpsTooLow | current | Sent when bias current is too small. For SFF Digital Diagnostics, this corresponds to the low bias current alarm. This Notification should be of Severity ERROR. | |
| 1.3.6.1.4.1.629.200.13.0.33 | NotificationnbsCmmcTrapPortAmpsTooHigh | current | Sent when bias current is too large. For SFF Digital Diagnostics, this corresponds to the high bias current alarm. This Notification should be of Severity ERRO… | |
| 1.3.6.1.4.1.629.200.13.0.34 | NotificationnbsCmmcTrapPortVoltsTooLow | current | Sent when transceiver supply voltage is too low. For SFF Digital Diagnostics, this corresponds to the low supply voltage alarm. This Notification should be of … | |
| 1.3.6.1.4.1.629.200.13.0.35 | NotificationnbsCmmcTrapPortVoltsTooHigh | current | Sent when transceiver supply voltage is too high. For SFF Digital Diagnostics, this corresponds to the high supply voltage alarm. This Notification should be o… | |
| 1.3.6.1.4.1.629.200.13.0.36 | NotificationnbsCmmcTrapSwitchover | current | Sent when a self-healing (redundant ports) card switches traffic from an active port to a standby port. This Notification should be of Severity WARNING. The VA… | |
| 1.3.6.1.4.1.629.200.13.0.37 | NotificationnbsCmmcTrapSlotShuttingDown | current | Sent when the slot/card is shutting down. This Notification should be of Severity WARNING if the shutdown is deliberate, or ERROR if shutdown because of module… | |
| 1.3.6.1.4.1.629.200.13.0.38 | NotificationnbsCmmcTrapPortCrcError | current | Sent when CRC Error is received on this port. This Notification should be of Severity WARNING. | |
| 1.3.6.1.4.1.629.200.13.0.39 | NotificationnbsCmmcTrapCpeInManagedChassis | current | Sent when a module configured for customer premises is detected in a managed (central office) chassis. This Notification should be of Severity WARNING. To enab… | |
| 1.3.6.1.4.1.629.200.13.0.40 | NotificationnbsCmmcTrapCoWithoutCpe | current | Sent when a central office module has no link to a CPE module. This Notification should be of Severity WARNING. To enable/disable this notification, use the ob… | |
| 1.3.6.1.4.1.629.200.13.0.41 | NotificationnbsCmmcTrapCoTakesControl | current | Sent when a central office module begins active management of a dual-homed CPE module. This Notification should be of Severity WARNING. To enable/disable this … | |
| 1.3.6.1.4.1.629.200.13.0.42 | NotificationnbsCmmcTrapCoYieldsControl | current | Sent when a central office module ceases active management of a dual-homed CPE module. This Notification should be of Severity WARNING. To enable/disable this … | |
| 1.3.6.1.4.1.629.200.13.0.43 | NotificationnbsCmmcTrapCoLinkedToCo | current | Sent when one central office module is connected to another central office module. This Notification should be of Severity ERROR. To enable/disable this notifi… | |
| 1.3.6.1.4.1.629.200.13.0.44 | NotificationnbsCmmcTrapCpeFound | current | Sent when a remote CPE module is detected. This Notification should be of Severity WARNING. To enable/disable this notification, use the object nbsCmmcChassisE… | |
| 1.3.6.1.4.1.629.200.13.0.45 | NotificationnbsCmmcTrapPortReflectionDetected | current | Sent when SingleFiber port detects its own signal reflecting back on itself. This Notification should be of Severity WARNING. | |
| 1.3.6.1.4.1.629.200.13.0.46 | NotificationnbsCmmcTrapPortReflectionCeased | current | Sent when SingleFiber port no longer detects its own signal returning. This Notification should be of Severity WARNING. | |
| 1.3.6.1.4.1.629.200.13.0.47 | NotificationnbsCmmcTrapPortTempOk | current | Sent when transmitter temperature returns to normal. For Agent's internal severity-based filtering. The severity of this NOTIFICATION must match the severity o… | |
| 1.3.6.1.4.1.629.200.13.0.48 | NotificationnbsCmmcTrapPortRxPowerOk | current | Sent when received signal returns to normal. For Agent's internal severity-based filtering. The severity of this NOTIFICATION must match the severity of the nb… | |
| 1.3.6.1.4.1.629.200.13.0.49 | NotificationnbsCmmcTrapPortTxPowerOk | current | Sent when transmitter power returns to normal. For Agent's internal severity-based filtering. The severity of this NOTIFICATION must match the severity of the … | |
| 1.3.6.1.4.1.629.200.13.0.50 | NotificationnbsCmmcTrapPortAmpsOk | current | Sent when bias current returns to normal. For Agent's internal severity-based filtering. The severity of this NOTIFICATION must match the severity of the nbsCm… | |
| 1.3.6.1.4.1.629.200.13.0.51 | NotificationnbsCmmcTrapPortVoltsOk | current | Sent when transceiver supply voltage returns to normal. For Agent's internal severity-based filtering. The severity of this NOTIFICATION must match the severit… | |
| 1.3.6.1.4.1.629.200.13.0.52 | NotificationnbsCmmcTrapSlotTempTooLow | current | Sent when slot temperature is too cold. This Notification should be of Severity ERROR. | |
| 1.3.6.1.4.1.629.200.13.0.53 | NotificationnbsCmmcTrapSlotTempTooHigh | current | Sent when slot temperature is too hot. temperature alarm. This Notification should be of Severity ERROR. | |
| 1.3.6.1.4.1.629.200.13.0.54 | NotificationnbsCmmcTrapSlotTempOk | current | Sent when slot temperature returns to normal. This Notification should be of Severity ERROR. | |
| 1.3.6.1.4.1.629.200.13.0.55 | NotificationnbsCmmcTrapPortErrorsDetected | current | Sent when nbsCmmcPortErrorActivity changes to on(3). This Notification should be of Severity WARNING. | |
| 1.3.6.1.4.1.629.200.13.0.56 | NotificationnbsCmmcTrapPortErrorsStopped | current | Sent when nbsCmmcPortErrorActivity changes to off(2). This Notification should be of Severity WARNING. | |
| 1.3.6.1.4.1.629.200.13.0.57 | NotificationnbsCmmcTrapChassisInsufficientPower | current | Sent when power on chassis changed to insufficient. This Notification should be of Severity ERROR. | |
| 1.3.6.1.4.1.629.200.13.0.58 | NotificationnbsCmmcTrapChassisSufficientPower | current | Sent when power on chassis changed to sufficient. This Notification should be of Severity ERROR. | |
| 1.3.6.1.4.1.629.200.13.0.59 | NotificationnbsCmmcTrapSlotModuleLocked | current | Sent when nbsCmmcSysLockTypes is enabled(3) and a card incompatible with a slot's locked configuration is inserted. This Notification should be of Severity ERR… | |
| 1.3.6.1.4.1.629.200.13.0.60 | NotificationnbsCmmcTrapSelectLinkChanged | current | Sent when a redundant port in a self-healing card switches between active and standby. The last varbind, nbsCmmcPortSelectLink, indicates this port's new state… | |
| 1.3.6.1.4.1.629.200.13.0.66 | NotificationnbsCmmcTrapPowerSupplyRemoved | current | Event triggered by physical removal of a power supply. This Notification should be of Severity ERROR. | |
| 1.3.6.1.4.1.629.200.13.0.67 | NotificationnbsCmmcTrapPowerSupplyInserted | current | Triggered by physical insertion of a power supply. This Notification should be of Severity ERROR. | |
| 1.3.6.1.4.1.629.200.13.0.68 | NotificationnbsCmmcTrapFanRemoved | current | Triggered by physical removal of fan assembly. This Notification should be of Severity WARNING. | |
| 1.3.6.1.4.1.629.200.13.0.69 | NotificationnbsCmmcTrapFanInserted | current | Triggered by physical insertion of fan assembly. This Notification should be of Severity WARNING. | |
| 1.3.6.1.4.1.629.200.13.0.70 | NotificationnbsCmmcTrapModuleStatusChanged | current | Triggered when nbsCmmcSlotModuleStatus changes. If a module is unplugged and nbsCmmcSlotModuleStatus transitions directly to empty(2), a trap will not be gener… |