NETGEAR-RADLAN-rlInterfaces
100 objects
The MIB module describes the private MIB for Switch Interfaces supported by Marvell MTS software and products.
Imported Objects
| IF-MIB | ifIndex InterfaceIndex InterfaceIndexOrZero |
| NETGEAR-RADLAN-MIB | rlIfInterfaces rnd |
| Q-BRIDGE-MIB | PortList |
| SNMPv2-SMI | Counter32 Integer32 MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString RowStatus TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.4526.17.43 | IdentityswInterfaces | The MIB module describes the private MIB for Switch Interfaces supported by Marvell MTS software and products. | ||
| 1.3.6.1.4.1.4526.17.43.1 | TableswIfTable | not-accessible | current | Switch media specific information and configuration of the device interfaces. |
| 1.3.6.1.4.1.4526.17.43.1.1 | RowswIfEntry | not-accessible | current | Defines the contents of each line in the swIfTable table. |
| 1.3.6.1.4.1.4526.17.43.1.1.1 | ColumnswIfIndex | read-only | current | Index to the swIfTable. The interface defined by a particular value of this index is the same interface as identified by the same value of ifIndex (MIB II). |
| 1.3.6.1.4.1.4526.17.43.1.1.2 | ColumnswIfPhysAddressType | read-write | obsolete | This variable indicates whether the physical address assigned to this interface should be the default one or be chosen from the set of reserved physical addres… |
| 1.3.6.1.4.1.4526.17.43.1.1.3 | ColumnswIfDuplexAdminMode | read-write | current | This variable specifies whether this interface should operate in half duplex or full duplex mode. This specification will take effect only if swIfSpeedDuplexAu… |
| 1.3.6.1.4.1.4526.17.43.1.1.4 | ColumnswIfDuplexOperMode | read-only | current | This variable indicates whether this interface operates in half duplex or full duplex mode. This variable can have the values hybrid or unknown only for a trun… |
| 1.3.6.1.4.1.4526.17.43.1.1.5 | ColumnswIfBackPressureMode | read-write | current | This variable indicates whether this interface activates back pressure when congested. |
| 1.3.6.1.4.1.4526.17.43.1.1.6 | ColumnswIfTaggedMode | read-write | current | If enable, this interface operates in tagged mode, i.e all frames sent out through this interface will have the 802.1Q header. If disabled the frames will not … |
| 1.3.6.1.4.1.4526.17.43.1.1.7 | ColumnswIfTransceiverType | read-only | current | This variable indicates the transceiver type of this interface. |
| 1.3.6.1.4.1.4526.17.43.1.1.8 | ColumnswIfLockAdminStatus | read-write | current | This variable indicates whether this interface should operate in locked or unlocked mode. In unlocked mode the device learns all MAC addresses from this port a… |
| 1.3.6.1.4.1.4526.17.43.1.1.9 | ColumnswIfLockOperStatus | read-only | current | This variable defines whether this interface operates in locked or unlocked mode. It is locked in each of the following two cases: 1) if swLockAdminStatus is s… |
| 1.3.6.1.4.1.4526.17.43.1.1.10 | ColumnswIfType | read-only | current | This variable specifies the type of interface. |
| 1.3.6.1.4.1.4526.17.43.1.1.11 | ColumnswIfDefaultTag | read-only | current | This variable specifies the default VLAN tag which will be attached to outgoing frames if swIfTaggedMode for this interface is enabled. |
| 1.3.6.1.4.1.4526.17.43.1.1.12 | ColumnswIfDefaultPriority | read-write | current | This variable specifies the default port priority. |
| 1.3.6.1.4.1.4526.17.43.1.1.13 | ColumnswIfStatus | read-write | current | The status of a table entry. It is used to delete an entry from this table. |
| 1.3.6.1.4.1.4526.17.43.1.1.14 | ColumnswIfFlowControlMode | read-write | current | on - Flow control will be enabled on this interface according to the IEEE 802.3x standard. off - Flow control is disabled. autoNegotiation - Flow control will … |
| 1.3.6.1.4.1.4526.17.43.1.1.15 | ColumnswIfSpeedAdminMode | read-write | current | This variable specifies the required speed of this interface in bits per second. This specification will take effect only if swIfSpeedDuplexAutoNegotiation is … |
| 1.3.6.1.4.1.4526.17.43.1.1.16 | ColumnswIfSpeedDuplexAutoNegotiation | read-write | current | If enabled the speed and duplex mode will be set by the device through the autonegotiation process. Otherwise these characteristics will be set according to th… |
| 1.3.6.1.4.1.4526.17.43.1.1.17 | ColumnswIfOperFlowControlMode | read-only | current | on - Flow control is enabled on this interface according to the IEEE 802.3x standard. off - Flow control is disabled. enabledRx - Flow control is enabled on th… |
| 1.3.6.1.4.1.4526.17.43.1.1.18 | ColumnswIfOperSpeedDuplexAutoNegotiation | read-only | current | If enabled the speed and duplex are determined by the device through the autonegotiation process. If disabled these characteristics are determined according to… |
| 1.3.6.1.4.1.4526.17.43.1.1.19 | ColumnswIfOperBackPressureMode | read-only | current | This variable indicates the operative back pressure mode of this interface. |
| 1.3.6.1.4.1.4526.17.43.1.1.20 | ColumnswIfAdminLockAction | read-write | current | This variable indicates which action this interface should be taken in locked mode and therefore relevant only in locked mode. Possible actions: discard(1) - e… |
| 1.3.6.1.4.1.4526.17.43.1.1.21 | ColumnswIfOperLockAction | read-only | current | This variable indicates which action this interface actually takes in locked mode and therefore relevant only in locked mode. Possible actions: discard(1) - ev… |
| 1.3.6.1.4.1.4526.17.43.1.1.22 | ColumnswIfAdminLockTrapEnable | read-write | current | This variable indicates whether to create a SNMP trap in the locked mode. |
| 1.3.6.1.4.1.4526.17.43.1.1.23 | ColumnswIfOperLockTrapEnable | read-only | current | This variable indicates whether a SNMP trap can be created in the locked mode. |
| 1.3.6.1.4.1.4526.17.43.1.1.24 | ColumnswIfOperSuspendedStatus | read-only | current | This variable indicates whether the port is suspended or not due to some feature. After reboot this value is false |
| 1.3.6.1.4.1.4526.17.43.1.1.25 | ColumnswIfLockOperTrapCount | read-only | current | This variable indicates the trap counter status per ifIndex (i.e. number of received packets since the last trap sent due to a packet which was received on thi… |
| 1.3.6.1.4.1.4526.17.43.1.1.26 | ColumnswIfLockAdminTrapFrequency | read-write | current | This variable indicates the minimal frequency (in seconds) of sending a trap per ifIndex. It's relevant only in locked mode and in trap enabled. |
| 1.3.6.1.4.1.4526.17.43.1.1.27 | ColumnswIfReActivate | read-write | current | This variable reactivates (enables) an ifIndex (which was suspended) |
| 1.3.6.1.4.1.4526.17.43.1.1.28 | ColumnswIfAdminMdix | read-write | current | The configuration is on a physical port, not include trunks. cross - The interface should force crossover. normal - The interface should not force crossover. a… |
| 1.3.6.1.4.1.4526.17.43.1.1.29 | ColumnswIfOperMdix | read-only | current | cross - The interface is in crossover mode. normal - The interface is not in crossover mode. unknown - Only for port that its operative status is not present o… |
| 1.3.6.1.4.1.4526.17.43.1.1.30 | ColumnswIfHostMode | read-write | current | This variable indicates the 802.1X host mode of a port. Relevant when the port's 802.1X control is auto. In addtion multiple-auth was added. |
| 1.3.6.1.4.1.4526.17.43.1.1.31 | ColumnswIfSingleHostViolationAdminAction | read-write | current | This variable indicates which action this interface should take in single authorized. Possible actions: discard - every packet is dropped. forwardNormal - ever… |
| 1.3.6.1.4.1.4526.17.43.1.1.32 | ColumnswIfSingleHostViolationOperAction | read-only | current | This variable indicates which action this interface actually takes in single authorized. Possible actions: discard(1) - every packet is dropped. forwardNormal(… |
| 1.3.6.1.4.1.4526.17.43.1.1.33 | ColumnswIfSingleHostViolationAdminTrapEnable | read-write | current | This variable indicates whether to create a SNMP trap in single authorized. |
| 1.3.6.1.4.1.4526.17.43.1.1.34 | ColumnswIfSingleHostViolationOperTrapEnable | read-only | current | This variable indicates whether a SNMP trap can be created in the single authorized. |
| 1.3.6.1.4.1.4526.17.43.1.1.35 | ColumnswIfSingleHostViolationOperTrapCount | read-only | current | This variable indicates the trap counter status per ifIndex (i.e. number of received packets since the last trap sent due to a packet which was received on thi… |
| 1.3.6.1.4.1.4526.17.43.1.1.36 | ColumnswIfSingleHostViolationAdminTrapFrequency | read-write | current | This variable indicates the minimal frequency (in seconds) of sending a trap per ifIndex. It's relevant only in single authorized and in trap enabled. A value … |
| 1.3.6.1.4.1.4526.17.43.1.1.37 | ColumnswIfLockLimitationMode | read-write | current | This variable indicates what is the learning limitation on the locked interface. Possible values: disabled - learning is stopped. The dynamic addresses associa… |
| 1.3.6.1.4.1.4526.17.43.1.1.38 | ColumnswIfLockMaxMacAddresses | read-write | current | This variable defines the maximum number of dynamic addresses that can be asscoiated with the locked interface. It isn't relevant in disabled limitation mode. |
| 1.3.6.1.4.1.4526.17.43.1.1.39 | ColumnswIfLockMacAddressesCount | read-only | current | This variable indicates the actual number of dynamic addresses that can be asscoiated with the locked interface. It isn't relevant in disabled limitation mode. |
| 1.3.6.1.4.1.4526.17.43.1.1.40 | ColumnswIfAdminSpeedDuplexAutoNegotiationLocalCapabilities | read-write | current | Administrative auto negotiation capabilities of the interface that can be advertised when swIfSpeedDuplexAutoNegotiation is enabled. default bit means advertis… |
| 1.3.6.1.4.1.4526.17.43.1.1.41 | ColumnswIfOperSpeedDuplexAutoNegotiationLocalCapabilities | read-only | current | Operative auto negotiation capabilities of the remote link. unknown bit means that port operative status is not up. |
| 1.3.6.1.4.1.4526.17.43.1.1.42 | ColumnswIfSpeedDuplexNegotiationRemoteCapabilities | read-only | current | Operative auto negotiation capabilities of the remote link. unknown bit means that port operative status is not up, or auto negotiation process not complete, o… |
| 1.3.6.1.4.1.4526.17.43.1.1.43 | ColumnswIfAdminComboMode | read-write | current | This variable specifies the administrative mode of a combo Ethernet interface. |
| 1.3.6.1.4.1.4526.17.43.1.1.44 | ColumnswIfOperComboMode | read-only | current | This variable specifies the operative mode of a combo Ethernet interface. |
| 1.3.6.1.4.1.4526.17.43.1.1.45 | ColumnswIfAutoNegotiationMasterSlavePreference | read-write | current | This variable specifies the administrative mode of the Maste-Slave preference in auto negotiation. |
| 1.3.6.1.4.1.4526.17.43.2 | ScalarswIfMibVersion | read-only | current | The swIfTable Mib's version, the current version is 3. |
| 1.3.6.1.4.1.4526.17.43.3 | ScalarswIfPortLockSupport | read-only | current | indicates if the locked port package is supported. |
| 1.3.6.1.4.1.4526.17.43.4 | ScalarswIfPortLockActionSupport | read-only | current | indicates which port lock actions are supported: (bit 0 is the most significant bit) bit 0 - discard bit 1 - forwardNormal bit 2 - discardDisable |
| 1.3.6.1.4.1.4526.17.43.5 | ScalarswIfPortLockTrapSupport | read-only | current | indicates with which port lock actions the trap option is supported (e.g. discard indicates that trap is supported only when the portlock action is discard): (… |
| 1.3.6.1.4.1.4526.17.43.6 | TableswIfPortLockIfRangeTable | not-accessible | current | Port lock interfaces range configuration |
| 1.3.6.1.4.1.4526.17.43.6.1 | RowswIfPortLockIfRangeEntry | not-accessible | current | Defines the contents of each line in the swIfPortLockIfRangeTable table. |
| 1.3.6.1.4.1.4526.17.43.6.1.1 | ColumnswIfPortLockIfRangeIndex | read-only | current | Index to the swIfPortLockIfRangeTable. |
| 1.3.6.1.4.1.4526.17.43.6.1.2 | ColumnswIfPortLockIfRange | read-write | current | The set of interfaces to which the port lock parameters should be configured |
| 1.3.6.1.4.1.4526.17.43.6.1.3 | ColumnswIfPortLockIfRangeLockStatus | read-write | current | This variable indicates whether the interfaces range should operate in locked or unlocked mode. In unlocked mode the device learns all MAC addresses from these… |
| 1.3.6.1.4.1.4526.17.43.6.1.4 | ColumnswIfPortLockIfRangeAction | read-write | current | This variable indicates which action for these interfaces should be take in locked mode and therefore relevant only in locked mode. Possible actions: discard(1… |
| 1.3.6.1.4.1.4526.17.43.6.1.5 | ColumnswIfPortLockIfRangeTrapEn | read-write | current | This variable indicates whether to create a SNMP trap in the locked mode. |
| 1.3.6.1.4.1.4526.17.43.6.1.6 | ColumnswIfPortLockIfRangeTrapFreq | read-write | current | This variable indicates the minimal frequency (in seconds) of sending a trap for these interfaces. It's relevant only in locked mode and in trap enabled. |
| 1.3.6.1.4.1.4526.17.43.7 | TableswIfExtTable | not-accessible | current | Display information and configuration of the device interfaces. |
| 1.3.6.1.4.1.4526.17.43.7.1 | RowswIfExtEntry | not-accessible | current | Defines the contents of each row in the swIfExtTable. |
| 1.3.6.1.4.1.4526.17.43.7.1.1 | ColumnswIfExtSFPSpeed | read-write | current | Configure speed of an SFP Ethernet interface. |
| 1.3.6.1.4.1.4526.17.54.1 | ScalarrlIfMibVersion | read-only | current | MIB's version, the current version is 1. |
| 1.3.6.1.4.1.4526.17.54.2 | ScalarrlIfNumOfPhPorts | read-only | current | Total number of physical ports on this device (including all stack units) |
| 1.3.6.1.4.1.4526.17.54.3 | ScalarrlIfMapOfOnPhPorts | read-only | current | Each bit in this octet string indicates that the correspondig port's ifOperStatus is ON if set. The mapping of port number to bits in this octet string is as f… |
| 1.3.6.1.4.1.4526.17.54.4 | ScalarrlIfClearPortMibCounters | read-write | current | Each bit that is set in this portList represent a port that its mib counters should be reset. |
| 1.3.6.1.4.1.4526.17.54.5 | ScalarrlIfNumOfUserDefinedPorts | read-only | current | The number of user defined ports on this device. |
| 1.3.6.1.4.1.4526.17.54.6 | ScalarrlIfFirstOutOfBandIfIndex | read-only | current | First ifIndex of out-of-band port. This scalar exists only the device has out of band ports. |
| 1.3.6.1.4.1.4526.17.54.7 | ScalarrlIfNumOfLoopbackPorts | read-only | current | The number of loopback ports on this device. |
| 1.3.6.1.4.1.4526.17.54.8 | ScalarrlIfFirstLoopbackIfIndex | read-only | current | First ifIndex of loopback port. This scalar will exists only if rlIfNumOfLoopbackPorts is different from 0. |
| 1.3.6.1.4.1.4526.17.54.9 | ScalarrlIfExistingPortList | read-only | current | Indicates which ports/trunks exist in the system. It doesn't indicate which are present. |
| 1.3.6.1.4.1.4526.17.54.10 | ScalarrlIfBaseMACAddressPerIfIndex | read-write | current | Indicates if the system will assign a unique MAC per Ethernet port or not. |
| 1.3.6.1.4.1.4526.17.54.11 | ScalarrlFlowControlCascadeMode | read-write | current | enable disable flow control on cascade ports |
| 1.3.6.1.4.1.4526.17.54.12 | ScalarrlFlowControlCascadeType | read-write | current | define which type of ports will be affected by flow control on cascade ports |
| 1.3.6.1.4.1.4526.17.54.13 | ScalarrlFlowControlRxPerSystem | read-write | current | define if flow control RX is supported per system. |
| 1.3.6.1.4.1.4526.17.54.14 | ScalarrlCascadePortProtectionAction | read-write | current | As a result of this set all of the local cascade ports will stop being consider unstable and will be force up. |
| 1.3.6.1.4.1.4526.17.54.15 | ScalarrlManagementIfIndex | read-write | current | Specify L2 bound management interface index in a single IP address system when configurable management interface is supported. |
| 1.3.6.1.4.1.4526.17.54.16 | ScalarrlIfClearStackPortsCounters | read-write | current | As a result of this set all counters of all external cascade ports will be cleared. |
| 1.3.6.1.4.1.4526.17.54.17 | ScalarrlIfClearPortMacAddresses | read-write | current | if port is non secure, its all dynamic MAC addresses are cleared. if port is secure, its all secure MAC addresses which have learned or configured are cleared. |
| 1.3.6.1.4.1.4526.17.54.18 | ScalarrlIfCutThroughPacketLength | read-write | current | The default packet length that is assigned to a packet in the Cut-Through mode. |
| 1.3.6.1.4.1.4526.17.54.19 | ScalarrlIfCutPriorityZero | read-write | current | Enable or disable cut-Through for priority 0. |
| 1.3.6.1.4.1.4526.17.54.20 | ScalarrlIfCutPriorityOne | read-write | current | Enable or disable cut-Through for priority 1. |
| 1.3.6.1.4.1.4526.17.54.21 | ScalarrlIfCutPriorityTwo | read-write | current | Enable or disable cut-Through for priority 2. |
| 1.3.6.1.4.1.4526.17.54.22 | ScalarrlIfCutPriorityThree | read-write | current | Enable or disable cut-Through for priority 3. |
| 1.3.6.1.4.1.4526.17.54.23 | ScalarrlIfCutPriorityFour | read-write | current | Enable or disable cut-Through for priority 4. |
| 1.3.6.1.4.1.4526.17.54.24 | ScalarrlIfCutPriorityFive | read-write | current | Enable or disable cut-Through for priority 5. |
| 1.3.6.1.4.1.4526.17.54.25 | ScalarrlIfCutPrioritySix | read-write | current | Enable or disable cut-Through for priority 6. |
| 1.3.6.1.4.1.4526.17.54.26 | ScalarrlIfCutPrioritySeven | read-write | current | Enable or disable cut-Through for priority 7. |
| 1.3.6.1.4.1.4526.17.54.27 | TablerlIfCutThroughTable | not-accessible | current | Information and configuration of cut-through feature. |
| 1.3.6.1.4.1.4526.17.54.27.1 | RowrlIfCutThroughEntry | not-accessible | current | Defines the contents of each line in the swIfTable table. |
| 1.3.6.1.4.1.4526.17.54.27.1.1 | ColumnrlIfCutThroughPriorityEnable | read-write | current | Enable or disable cut-through for a priority for an interface. |
| 1.3.6.1.4.1.4526.17.54.27.1.2 | ColumnrlIfCutThroughUntaggedEnable | read-write | current | Enable or disable cut-through for untagged packets for an interface. |
| 1.3.6.1.4.1.4526.17.54.27.1.3 | ColumnrlIfCutThroughOperMode | read-only | current | Operational mode of spesific cut-through interface. |
| 1.3.6.1.4.1.4526.17.54.28 | ScalarrlCutThroughPacketLength | read-only | current | The default packet length that is assigned to a packet in the Cut-Through mode. |
| 1.3.6.1.4.1.4526.17.54.29 | ScalarrlCutThroughPacketLengthAfterReset | read-write | current | The default packet length that is assigned to a packet in the Cut-Through mode after reset. |
| 1.3.6.1.4.1.4526.17.54.30 | ScalarrlCutThroughEnable | read-only | current | Cut-Through global enable mode. |
| 1.3.6.1.4.1.4526.17.54.31 | ScalarrlCutThroughEnableAfterReset | read-write | current | Cut-Through global enable mode after reset. |
| 1.3.6.1.4.1.4526.17.54.32 | ScalarrlFlowControlMode | read-write | current | Define which mode will be enabled on flow control enabled ports. The interfaces with enabled flow control will receive pause frames, but will not send flow con… |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| AutoNegCapabilitiesBits | BITS { default(0), unknown(1), tenHalf(2), tenFull(3), fastHalf(4), fastFull(5), gigaHalf(6), gigaFull(7), tenGigaFull(8) } | current | Auto negotiation capabilities bits. |