NETGEAR-SMART-SWITCHING-MIB
475 objects
The Netgear Private MIB for Switching
Imported Objects
| IANAifType-MIB | IANAifType |
| IF-MIB | ifIndex |
| INET-ADDRESS-MIB | InetAddress InetAddressType |
| NETGEAR-REF-MIB | ng700smartswitch |
| Q-BRIDGE-MIB | dot1qFdbId dot1qTpFdbAddress dot1qVlanIndex VlanIndex |
| RFC1213-MIB | DisplayString PhysAddress |
| SNMPv2-SMI | Counter32 Gauge32 Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | DateAndTime MacAddress RowStatus |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.4526.11.1 | IdentityagentSwitching | The Netgear Private MIB for Switching | ||
| 1.3.6.1.4.1.4526.11.1.0 | NodeagentSwitchingTraps | |||
| 1.3.6.1.4.1.4526.11.1.0.1 | NotificationmultipleUsersTrap | current | This trap is sent when more than one user is logged in with administrative access. Only applies to CLI interface. | |
| 1.3.6.1.4.1.4526.11.1.0.2 | NotificationbroadcastStormStartTrap | obsolete | This trap is sent when a broadcast storm is detected. | |
| 1.3.6.1.4.1.4526.11.1.0.3 | NotificationbroadcastStormEndTrap | obsolete | This trap is sent when a broadcast storm is no longer detected. | |
| 1.3.6.1.4.1.4526.11.1.0.4 | NotificationlinkFailureTrap | obsolete | ||
| 1.3.6.1.4.1.4526.11.1.0.5 | NotificationvlanRequestFailureTrap | obsolete | ||
| 1.3.6.1.4.1.4526.11.1.0.6 | NotificationvlanDeleteLastTrap | current | Trap is sent when attempting to delete the last configured VLAN or the Default VLAN. | |
| 1.3.6.1.4.1.4526.11.1.0.7 | NotificationvlanDefaultCfgFailureTrap | current | Trap is sent if there are failures in resetting VLAN configuration to defaults. | |
| 1.3.6.1.4.1.4526.11.1.0.8 | NotificationvlanRestoreFailureTrap | obsolete | ||
| 1.3.6.1.4.1.4526.11.1.0.9 | NotificationfanFailureTrap | obsolete | ||
| 1.3.6.1.4.1.4526.11.1.0.10 | NotificationstpInstanceNewRootTrap | current | Trap is sent when this machine is a new STP Root when there is more than one STP instance. | |
| 1.3.6.1.4.1.4526.11.1.0.11 | NotificationstpInstanceTopologyChangeTrap | current | Trap is sent when there is a STP topology change when there is more than one STP instance. | |
| 1.3.6.1.4.1.4526.11.1.0.12 | NotificationpowerSupplyStatusChangeTrap | obsolete | ||
| 1.3.6.1.4.1.4526.11.1.0.13 | NotificationfailedUserLoginTrap | current | Trap is sent when a user fails to authenticate via the CLI or Web interfaces. | |
| 1.3.6.1.4.1.4526.11.1.0.14 | NotificationuserLockoutTrap | current | Trap is sent when a user account is locked due to consecutive failed login attempts via the CLI or Web interfaces beyond the allowed limit. | |
| 1.3.6.1.4.1.4526.11.1.0.15 | NotificationmacAddrLearnTrap | current | Trap is sent when L2 MAC address is learned i.e when entry is added to FDB. | |
| 1.3.6.1.4.1.4526.11.1.0.16 | NotificationmacAddrAgeoutTrap | current | Trap is sent when L2 MAC address is agedout i.e when entry is removed from FDB. | |
| 1.3.6.1.4.1.4526.11.1.1 | NodeagentInfoGroup | |||
| 1.3.6.1.4.1.4526.11.1.1.1 | NodeagentInventoryGroup | |||
| 1.3.6.1.4.1.4526.11.1.1.1.1 | ScalaragentInventorySysDescription | read-only | current | The switch's Inventory system description. |
| 1.3.6.1.4.1.4526.11.1.1.1.2 | ScalaragentInventoryMachineType | read-only | current | Type of the Machine used in the Switch |
| 1.3.6.1.4.1.4526.11.1.1.1.3 | ScalaragentInventoryMachineModel | read-only | current | The switch's Machine Model. |
| 1.3.6.1.4.1.4526.11.1.1.1.4 | ScalaragentInventorySerialNumber | read-only | current | Serial number of the switch. |
| 1.3.6.1.4.1.4526.11.1.1.1.5 | ScalaragentInventoryFRUNumber | read-only | current | FRU Number of the switch |
| 1.3.6.1.4.1.4526.11.1.1.1.6 | ScalaragentInventoryMaintenanceLevel | read-only | current | The switch's Inventory Maintenance Level |
| 1.3.6.1.4.1.4526.11.1.1.1.7 | ScalaragentInventoryPartNumber | read-only | current | The switch's Inventory Part Number |
| 1.3.6.1.4.1.4526.11.1.1.1.8 | ScalaragentInventoryManufacturer | read-only | current | Name of the Manufacturer of this unit |
| 1.3.6.1.4.1.4526.11.1.1.1.9 | ScalaragentInventoryBurnedInMacAddress | read-only | current | Burned-In MAC Address |
| 1.3.6.1.4.1.4526.11.1.1.1.10 | ScalaragentInventoryOperatingSystem | read-only | current | Operating System running on this unit |
| 1.3.6.1.4.1.4526.11.1.1.1.11 | ScalaragentInventoryNetworkProcessingDevice | read-only | current | Network Processing Device for this unit |
| 1.3.6.1.4.1.4526.11.1.1.1.12 | ScalaragentInventoryAdditionalPackages | read-only | current | Lists additional functional packages available on this unit. |
| 1.3.6.1.4.1.4526.11.1.1.1.13 | ScalaragentInventorySoftwareVersion | read-only | current | Lists the version of software loaded on this unit. |
| 1.3.6.1.4.1.4526.11.1.1.2 | NodeagentTrapLogGroup | |||
| 1.3.6.1.4.1.4526.11.1.1.2.1 | ScalaragentTrapLogTotal | read-only | current | The total number of traps sent since last reset. |
| 1.3.6.1.4.1.4526.11.1.1.2.3 | ScalaragentTrapLogTotalSinceLastViewed | read-only | current | The number of traps sent since last viewed. |
| 1.3.6.1.4.1.4526.11.1.1.2.4 | TableagentTrapLogTable | not-accessible | current | Agent Trap Log |
| 1.3.6.1.4.1.4526.11.1.1.2.4.1 | RowagentTrapLogEntry | not-accessible | current | Agent trap log entry |
| 1.3.6.1.4.1.4526.11.1.1.2.4.1.1 | ColumnagentTrapLogIndex | read-only | current | Unique index of trap entry |
| 1.3.6.1.4.1.4526.11.1.1.2.4.1.2 | ColumnagentTrapLogSystemTime | read-only | current | System uptime when trap was sent. This entry shows how long the system has been up when the trap occurred. |
| 1.3.6.1.4.1.4526.11.1.1.2.4.1.3 | ColumnagentTrapLogTrap | read-only | current | Description of the trap sent. |
| 1.3.6.1.4.1.4526.11.1.1.3 | TableagentSupportedMibTable | not-accessible | current | Supported MIB table |
| 1.3.6.1.4.1.4526.11.1.1.3.1 | RowagentSupportedMibEntry | not-accessible | current | Supported MIB entry |
| 1.3.6.1.4.1.4526.11.1.1.3.1.1 | ColumnagentSupportedMibIndex | read-only | current | Unique index of the Supported MIB entry |
| 1.3.6.1.4.1.4526.11.1.1.3.1.2 | ColumnagentSupportedMibName | read-only | current | The name of the MIB (RFC or IEEE) that is supported. |
| 1.3.6.1.4.1.4526.11.1.1.3.1.3 | ColumnagentSupportedMibDescription | read-only | current | Description of the MIB (RFC or IEEE) that is supported. |
| 1.3.6.1.4.1.4526.11.1.2 | NodeagentConfigGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.1 | NodeagentCLIConfigGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.1.1 | TableagentLoginSessionTable | not-accessible | current | A table of the switch's login session |
| 1.3.6.1.4.1.4526.11.1.2.1.1.1 | RowagentLoginSessionEntry | not-accessible | current | Login Session Entry |
| 1.3.6.1.4.1.4526.11.1.2.1.1.1.1 | ColumnagentLoginSessionIndex | read-only | current | Agent Login Session Index of the switch |
| 1.3.6.1.4.1.4526.11.1.2.1.1.1.2 | ColumnagentLoginSessionUserName | read-only | current | Agent Login Session UserName of the switch |
| 1.3.6.1.4.1.4526.11.1.2.1.1.1.3 | ColumnagentLoginSessionIPAddress | read-only | obsolete | Agent Login Session IP Address of the switch |
| 1.3.6.1.4.1.4526.11.1.2.1.1.1.4 | ColumnagentLoginSessionConnectionType | read-only | current | Agent Login Session Connection Type of the switch |
| 1.3.6.1.4.1.4526.11.1.2.1.1.1.5 | ColumnagentLoginSessionIdleTime | read-only | current | Agent Login Session Idle Time of the switch |
| 1.3.6.1.4.1.4526.11.1.2.1.1.1.6 | ColumnagentLoginSessionSessionTime | read-only | current | Agent Login Session Time of the switch |
| 1.3.6.1.4.1.4526.11.1.2.1.1.1.7 | ColumnagentLoginSessionStatus | read-write | current | Status of the user. active(1) - This connection is active. destroy(6) - Set to this value to disconnect this user. |
| 1.3.6.1.4.1.4526.11.1.2.1.1.1.8 | ColumnagentLoginSessionInetAddressType | read-only | current | Type of address agentLoginSessionInetAddress is returning. Can be either unknown(0), ipv4(1), or ipv6 (2). Will return unknown(0) in the case of a serial login. |
| 1.3.6.1.4.1.4526.11.1.2.1.1.1.9 | ColumnagentLoginSessionInetAddress | read-only | current | Inet Address of the connecting the user is logging in with. Will return a zero-length string in the case of a serial login. |
| 1.3.6.1.4.1.4526.11.1.2.1.2 | NodeagentTelnetConfigGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.1.2.1 | ScalaragentTelnetLoginTimeout | read-write | current | Telnet login timeout (minutes) Config telnet timeout will set the telnet session timeout value. A session is active as long as the session has not remained idl… |
| 1.3.6.1.4.1.4526.11.1.2.1.2.2 | ScalaragentTelnetMaxSessions | read-write | current | Maximum number of Telnet Sessions Config telnet maxsessions is an integer value from 0 to 5 that specifies the maximum number of telnet sessions that can be es… |
| 1.3.6.1.4.1.4526.11.1.2.1.2.3 | ScalaragentTelnetAllowNewMode | read-write | current | Allow new telnet sessions (enable or disable) Config telnet disable means that no new Telnet sessions are to be established. Any already established session re… |
| 1.3.6.1.4.1.4526.11.1.2.1.3 | NodeagentUserConfigGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.1.3.1 | ScalaragentUserConfigCreate | read-write | current | Create a new user. When set with a non-empty string, a new user with that name will be created. This object will only return an empty string. This string is li… |
| 1.3.6.1.4.1.4526.11.1.2.1.3.2 | TableagentUserConfigTable | not-accessible | current | User Config Table |
| 1.3.6.1.4.1.4526.11.1.2.1.3.2.1 | RowagentUserConfigEntry | not-accessible | current | User Config Entry |
| 1.3.6.1.4.1.4526.11.1.2.1.3.2.1.1 | ColumnagentUserIndex | not-accessible | current | Agent User Config Index |
| 1.3.6.1.4.1.4526.11.1.2.1.3.2.1.2 | ColumnagentUserName | read-only | current | Agent User Name. This string is limited to alpha-numeric strings (including the '-' and '_' characters). |
| 1.3.6.1.4.1.4526.11.1.2.1.3.2.1.3 | ColumnagentUserPassword | read-write | current | Agent User Password This object will return an empty string even if a password is set. |
| 1.3.6.1.4.1.4526.11.1.2.1.3.2.1.4 | ColumnagentUserAccessMode | read-only | current | Agent User Access Mode |
| 1.3.6.1.4.1.4526.11.1.2.1.3.2.1.6 | ColumnagentUserAuthenticationType | read-write | current | SNMPv3 User Authentication. The user passsword must be set to a string greater than or equal to 8 characters for this to be set to anything but none(1). none(1… |
| 1.3.6.1.4.1.4526.11.1.2.1.3.2.1.7 | ColumnagentUserEncryptionType | read-write | current | SNMPv3 User Encryption Can not be set to des(2) if agentUserAuthenticationType is set to none(1). none(1) - no encryption used des(2) - DES encryption used |
| 1.3.6.1.4.1.4526.11.1.2.1.3.2.1.8 | ColumnagentUserEncryptionPassword | read-write | current | SNMPv3 User Encryption Password This object will return an empty string even if a password is set. agentUserEncryptionType must be set to des(2) before this ob… |
| 1.3.6.1.4.1.4526.11.1.2.1.3.2.1.9 | ColumnagentUserLockoutStatus | read-only | current | Displays whether the user account is locked due to excessive failed login attempts. |
| 1.3.6.1.4.1.4526.11.1.2.1.3.2.1.10 | ColumnagentUserPasswordExpireTime | read-only | current | Date and time when the user's password expires (past or present). Only valid when password aging is enabled. |
| 1.3.6.1.4.1.4526.11.1.2.1.5 | NodeagentSerialGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.1.5.1 | ScalaragentSerialTimeout | read-write | current | agentSerialTimeout specifies the maximum connect time(in minutes) without console activity. A value of 0 indicates that a console can be connected indefinitely… |
| 1.3.6.1.4.1.4526.11.1.2.1.5.2 | ScalaragentSerialBaudrate | read-write | current | agentSerialBaudrate specifies the current baud rate at which the serial port will try to connect. The available values are 1200, 2400, 4800, 9600, 19200, 38400… |
| 1.3.6.1.4.1.4526.11.1.2.1.5.3 | ScalaragentSerialCharacterSize | read-only | current | agentSerialCharacterSize specifies the number of bits in a character. The number of bits is always 8. |
| 1.3.6.1.4.1.4526.11.1.2.1.5.4 | ScalaragentSerialHWFlowControlMode | read-only | current | agentSerialHardwareFlowControl specifies whether hardware flow-control is enabled or disabled. Hardware Flow Control is always disabled. |
| 1.3.6.1.4.1.4526.11.1.2.1.5.5 | ScalaragentSerialStopBits | read-only | current | agentSerialStopBits specifies the number of Stop bits per character. The number of Stop bits is always 1. |
| 1.3.6.1.4.1.4526.11.1.2.1.5.6 | ScalaragentSerialParityType | read-only | current | agentSerialParityType specifies the Parity Method used on the Serial Port. The Parity Method is always None. |
| 1.3.6.1.4.1.4526.11.1.2.1.6 | NodeagentPasswordManagementConfigGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.1.6.1 | ScalaragentPasswordManagementMinLength | read-write | current | Minimum length for user passwords All new local user passwords must be at least this many characters in length. |
| 1.3.6.1.4.1.4526.11.1.2.1.6.2 | ScalaragentPasswordManagementHistory | read-write | current | The number of previous passwords to store for prevention of password reuse. This ensures that each user does not reuse passwords often. A value of 0 indicates … |
| 1.3.6.1.4.1.4526.11.1.2.1.6.3 | ScalaragentPasswordManagementAging | read-write | current | The maximum time that user passwords are valid, in days, from the time the password is set. Once a password expires, the user will be required to enter a new p… |
| 1.3.6.1.4.1.4526.11.1.2.1.6.4 | ScalaragentPasswordManagementLockAttempts | read-write | current | The number of allowable failed local authentication attempts before the user's account is locked. A value of 0 indicates that user accounts will never be locke… |
| 1.3.6.1.4.1.4526.11.1.2.2 | NodeagentLagConfigGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.2.1 | ScalaragentLagConfigCreate | read-write | current | Agent LAG Create. When this object is set with a non-empty string, a new LAG will be created if possible with the entered string as its name. |
| 1.3.6.1.4.1.4526.11.1.2.2.2 | TableagentLagSummaryConfigTable | not-accessible | current | A summary table of the switch's LAG config entries |
| 1.3.6.1.4.1.4526.11.1.2.2.2.1 | RowagentLagSummaryConfigEntry | not-accessible | current | Switch's LAG config entry |
| 1.3.6.1.4.1.4526.11.1.2.2.2.1.1 | ColumnagentLagSummaryLagIndex | read-only | current | Agent LAG IfIndex. This value corresponds with the LAG interface in the ifTable. |
| 1.3.6.1.4.1.4526.11.1.2.2.2.1.2 | ColumnagentLagSummaryName | read-write | current | Agent LAG Name. The associated name of the LAG used during creation. |
| 1.3.6.1.4.1.4526.11.1.2.2.2.1.3 | ColumnagentLagSummaryFlushTimer | read-write | obsolete | Agent LAG FlushTimer. |
| 1.3.6.1.4.1.4526.11.1.2.2.2.1.4 | ColumnagentLagSummaryLinkTrap | read-write | current | Agent LAG LinkTrap. Configures sending Link Up/Down traps when the LAG interface goes Up or Down. |
| 1.3.6.1.4.1.4526.11.1.2.2.2.1.5 | ColumnagentLagSummaryAdminMode | read-write | current | Agent LAG AdminMode. Administratively enables or disables this LAG interface. |
| 1.3.6.1.4.1.4526.11.1.2.2.2.1.6 | ColumnagentLagSummaryStpMode | read-write | current | Agent LAG StpMode If Dot1d is enabled, the valid values are: dot1d(1), fast(2), and off(3) If Dot1s is enabled, the valid values are: off(3) and dot1s(4) |
| 1.3.6.1.4.1.4526.11.1.2.2.2.1.7 | ColumnagentLagSummaryAddPort | read-write | current | Agent LAG AddPort. Set to a non 0 value to add a port to the LAG. Values correspond to ifIndex values in the ifTable. Note: agentPortType for the port to be ad… |
| 1.3.6.1.4.1.4526.11.1.2.2.2.1.8 | ColumnagentLagSummaryDeletePort | read-write | current | Agent LAG DeletePort. Set to a non 0 value to remove a port from the LAG. Values correspond to ifIndex values in the ifTable. |
| 1.3.6.1.4.1.4526.11.1.2.2.2.1.9 | ColumnagentLagSummaryStatus | read-write | current | Agent LAG Status. active(1) - This LAG is enabled. destroy(6) - Set to this value to remove the LAG. |
| 1.3.6.1.4.1.4526.11.1.2.2.2.1.10 | ColumnagentLagSummaryType | read-only | current | Agent LAG Type. static(1) - This LAG is staticly maintained. dynamic(2) - This LAG is dynamicly maintained. |
| 1.3.6.1.4.1.4526.11.1.2.2.2.1.11 | ColumnagentLagSummaryStaticCapability | read-write | current | Agent LAG Static Capability enable(1) - Static capability is enabled for this LAG interface disable(2) - Static capability is disabled for this LAG interface |
| 1.3.6.1.4.1.4526.11.1.2.2.3 | TableagentLagDetailedConfigTable | not-accessible | current | A detailed table of the switch's LAG config entries |
| 1.3.6.1.4.1.4526.11.1.2.2.3.1 | RowagentLagDetailedConfigEntry | not-accessible | current | Switch's LAG config entry |
| 1.3.6.1.4.1.4526.11.1.2.2.3.1.1 | ColumnagentLagDetailedLagIndex | read-only | current | LAG index |
| 1.3.6.1.4.1.4526.11.1.2.2.3.1.2 | ColumnagentLagDetailedIfIndex | read-only | current | LAG port index |
| 1.3.6.1.4.1.4526.11.1.2.2.3.1.3 | ColumnagentLagDetailedPortSpeed | read-only | current | LAG port speed. See agentPortType for a description and list of valid values. |
| 1.3.6.1.4.1.4526.11.1.2.2.3.1.4 | ColumnagentLagDetailedPortStatus | read-only | current | LAG port status. active(1) - Actively participating in the LAG. inactive(2) - Not participating in the LAG. |
| 1.3.6.1.4.1.4526.11.1.2.2.4 | ScalaragentLagConfigStaticCapability | read-write | obsolete | Agent LAG Static Capability. Configures whether Static LAGs are supported on this device. |
| 1.3.6.1.4.1.4526.11.1.2.3 | NodeagentNetworkConfigGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.3.1 | ScalaragentNetworkIPAddress | read-write | current | The switch's network ip address |
| 1.3.6.1.4.1.4526.11.1.2.3.2 | ScalaragentNetworkSubnetMask | read-write | current | The switch's network subnet mask |
| 1.3.6.1.4.1.4526.11.1.2.3.3 | ScalaragentNetworkDefaultGateway | read-write | current | The switch's network default gateway |
| 1.3.6.1.4.1.4526.11.1.2.3.4 | ScalaragentNetworkBurnedInMacAddress | read-only | current | The switch's network Burned-In MAC address |
| 1.3.6.1.4.1.4526.11.1.2.3.5 | ScalaragentNetworkLocalAdminMacAddress | read-write | current | The switch's network locally administered MAC address |
| 1.3.6.1.4.1.4526.11.1.2.3.6 | ScalaragentNetworkMacAddressType | read-write | current | The switch's network Mac Address Type |
| 1.3.6.1.4.1.4526.11.1.2.3.7 | ScalaragentNetworkConfigProtocol | read-write | current | The switch's network config protocol |
| 1.3.6.1.4.1.4526.11.1.2.3.8 | ScalaragentNetworkWebMode | read-write | obsolete | The switch's network config protocol on next bootup |
| 1.3.6.1.4.1.4526.11.1.2.3.9 | ScalaragentNetworkJavaMode | read-write | obsolete | Configures the use of the Java interface through the Web. |
| 1.3.6.1.4.1.4526.11.1.2.3.10 | ScalaragentNetworkMgmtVlan | read-write | current | The VLAN ID through which the switch can be managed using the agentNetworkIPAddress |
| 1.3.6.1.4.1.4526.11.1.2.3.11 | ScalaragentNetworkIpv6AdminMode | read-write | current | The network port IPv6 administrative state |
| 1.3.6.1.4.1.4526.11.1.2.3.12 | ScalaragentNetworkIpv6Gateway | read-write | current | The network port IPv6 Gateway Address |
| 1.3.6.1.4.1.4526.11.1.2.3.13 | TableagentNetworkIpv6AddrTable | not-accessible | current | The list of IPv6 address prefixes for the network port. |
| 1.3.6.1.4.1.4526.11.1.2.3.13.1 | RowagentNetworkIpv6AddrEntry | not-accessible | current | An interface entry containing objects of a particular IPv6 address prefix |
| 1.3.6.1.4.1.4526.11.1.2.3.13.1.1 | ColumnagentNetworkIpv6AddrPrefix | not-accessible | current | The service port IPv6 Address Prefix |
| 1.3.6.1.4.1.4526.11.1.2.3.13.1.2 | ColumnagentNetworkIpv6AddrPrefixLength | read-create | current | The service port IPv6 Address Prefix Length |
| 1.3.6.1.4.1.4526.11.1.2.3.13.1.3 | ColumnagentNetworkIpv6AddrEuiFlag | read-create | current | The service port IPv6 Eui Flag |
| 1.3.6.1.4.1.4526.11.1.2.3.13.1.4 | ColumnagentNetworkIpv6AddrStatus | read-create | current | |
| 1.3.6.1.4.1.4526.11.1.2.4 | NodeagentServicePortConfigGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.4.1 | ScalaragentServicePortIPAddress | read-write | current | The switch's ServicePort ip address |
| 1.3.6.1.4.1.4526.11.1.2.4.2 | ScalaragentServicePortSubnetMask | read-write | current | The switch's ServicePort subnet mask |
| 1.3.6.1.4.1.4526.11.1.2.4.3 | ScalaragentServicePortDefaultGateway | read-write | current | The switch's ServicePort default gateway |
| 1.3.6.1.4.1.4526.11.1.2.4.4 | ScalaragentServicePortBurnedInMacAddress | read-only | current | The switch's ServicePort Burned-In MAC address |
| 1.3.6.1.4.1.4526.11.1.2.4.5 | ScalaragentServicePortConfigProtocol | read-write | current | The switch's ServicePort config protocol |
| 1.3.6.1.4.1.4526.11.1.2.4.6 | ScalaragentServicePortIpv6AdminMode | read-write | current | The service port IPv6 administrative state |
| 1.3.6.1.4.1.4526.11.1.2.4.7 | ScalaragentServicePortIpv6Gateway | read-write | current | The service port IPv6 Gateway Address |
| 1.3.6.1.4.1.4526.11.1.2.4.8 | TableagentServicePortIpv6AddrTable | not-accessible | current | The list of IPv6 address prefixes for the service port. |
| 1.3.6.1.4.1.4526.11.1.2.4.8.1 | RowagentServicePortIpv6AddrEntry | not-accessible | current | An interface entry containing objects of a particular IPv6 address prefix |
| 1.3.6.1.4.1.4526.11.1.2.4.8.1.1 | ColumnagentServicePortIpv6AddrPrefix | not-accessible | current | The service port IPv6 Address Prefix |
| 1.3.6.1.4.1.4526.11.1.2.4.8.1.2 | ColumnagentServicePortIpv6AddrPrefixLength | read-create | current | The service port IPv6 Address Prefix Length |
| 1.3.6.1.4.1.4526.11.1.2.4.8.1.3 | ColumnagentServicePortIpv6AddrEuiFlag | read-create | current | The service port IPv6 Eui Flag |
| 1.3.6.1.4.1.4526.11.1.2.4.8.1.4 | ColumnagentServicePortIpv6AddrStatus | read-create | current | |
| 1.3.6.1.4.1.4526.11.1.2.6 | NodeagentSnmpConfigGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.6.1 | ScalaragentSnmpCommunityCreate | read-write | current | Creates a new SNMP Community entry. Defaults: IPAddress 0.0.0.0 IpMask 0.0.0.0 AccessMode read-only Status config |
| 1.3.6.1.4.1.4526.11.1.2.6.2 | TableagentSnmpCommunityConfigTable | not-accessible | current | A table of the switch's SNMP Config entries |
| 1.3.6.1.4.1.4526.11.1.2.6.2.1 | RowagentSnmpCommunityConfigEntry | not-accessible | current | Switch's SNMP Config entry |
| 1.3.6.1.4.1.4526.11.1.2.6.2.1.1 | ColumnagentSnmpCommunityIndex | read-only | current | The switch's Snmp Community Index |
| 1.3.6.1.4.1.4526.11.1.2.6.2.1.2 | ColumnagentSnmpCommunityName | read-write | current | The switch's Snmp Community Name This name identifies each SNMP community; the name can be up to 16 characters, and it is case-sensitive. Community names in th… |
| 1.3.6.1.4.1.4526.11.1.2.6.2.1.3 | ColumnagentSnmpCommunityIPAddress | read-write | current | The switch's Snmp Community IP Address Client IP Address - This attribute is an IP address (or portion thereof) from which this device will accept SNMP packets… |
| 1.3.6.1.4.1.4526.11.1.2.6.2.1.4 | ColumnagentSnmpCommunityIPMask | read-write | current | The switch's Snmp Community IP Mask Client IP Mask - This attribute is a mask to be logical-ANDed with the requesting entity's IP address before comparison wit… |
| 1.3.6.1.4.1.4526.11.1.2.6.2.1.5 | ColumnagentSnmpCommunityAccessMode | read-write | current | The switch's Snmp Community Access Mode Access Mode - This value can be read-only or read/write. A community with a read-only access allows for switch informat… |
| 1.3.6.1.4.1.4526.11.1.2.6.2.1.6 | ColumnagentSnmpCommunityStatus | read-write | current | The switch's Snmp Community Status. active(1) - This community is active, allowing SNMP managers associated with this community to manage the switch according … |
| 1.3.6.1.4.1.4526.11.1.2.6.3 | ScalaragentSnmpTrapReceiverCreate | read-write | current | Creates a new trap receiver entry. Defaults: IPAddress 0.0.0.0 status config |
| 1.3.6.1.4.1.4526.11.1.2.6.4 | TableagentSnmpTrapReceiverConfigTable | not-accessible | current | Trap messages are sent across a network to an SNMP Network Manager. These messages alert the manager to events occurring within the switch or on the network. U… |
| 1.3.6.1.4.1.4526.11.1.2.6.4.1 | RowagentSnmpTrapReceiverConfigEntry | not-accessible | current | Switch's Snmp Trace Receiver Config entry |
| 1.3.6.1.4.1.4526.11.1.2.6.4.1.1 | ColumnagentSnmpTrapReceiverIndex | read-only | current | The switch's Snmp Trap Receiver Index |
| 1.3.6.1.4.1.4526.11.1.2.6.4.1.2 | ColumnagentSnmpTrapReceiverCommunityName | read-write | current | The switch's Snmp Trap Receiver Community Name. This is the SNMP community name of the remote network manager; the name can be up to 16 characters, and is case… |
| 1.3.6.1.4.1.4526.11.1.2.6.4.1.3 | ColumnagentSnmpTrapReceiverIPAddress | read-write | current | IP Address - Each IP address parameter is four integer numbers. The numbers range from 0 to 255. |
| 1.3.6.1.4.1.4526.11.1.2.6.4.1.4 | ColumnagentSnmpTrapReceiverStatus | read-write | current | The switch's Snmp Trap Reciever Status. active(1) - This trap receiver is active, allowing SNMP Traps to be sent to this receiver. notInService(2) - This trap … |
| 1.3.6.1.4.1.4526.11.1.2.6.4.1.5 | ColumnagentSnmpTrapReceiverVersion | read-write | current | The version of trap sent to this Reciever. snmpv1(1) - This will send a SNMPv1 trap. snmpv2c(2) - This will send a SNMPv2c trap. |
| 1.3.6.1.4.1.4526.11.1.2.6.4.1.6 | ColumnagentSnmpTrapReceiverIpv6Address | read-write | current | IPv6 Address for SNMP receiver. |
| 1.3.6.1.4.1.4526.11.1.2.6.5 | NodeagentSnmpTrapFlagsConfigGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.6.5.1 | ScalaragentSnmpAuthenticationTrapFlag | read-write | current | Authentication Flag - Enable/Disable authentication Flag. |
| 1.3.6.1.4.1.4526.11.1.2.6.5.2 | ScalaragentSnmpLinkUpDownTrapFlag | read-write | current | Link Up/Down Flag - Enable/Disable Link Up/Link Down traps for the entire switch. When set to Enable, the Link Up/Down traps will be sent only if the Link Trap… |
| 1.3.6.1.4.1.4526.11.1.2.6.5.3 | ScalaragentSnmpMultipleUsersTrapFlag | read-write | current | Multiple Users Flag - Enable/Disable Multiple User traps. When the value is set to Enable, a Multiple User Trap is sent whenever someone logs in to the termina… |
| 1.3.6.1.4.1.4526.11.1.2.6.5.4 | ScalaragentSnmpSpanningTreeTrapFlag | read-write | current | Spanning Tree Flag - This flag enables the sending of new root traps and topology change notification traps. |
| 1.3.6.1.4.1.4526.11.1.2.6.5.5 | ScalaragentSnmpBroadcastStormTrapFlag | read-write | obsolete | Broadcast Storm Flag - This flag enables or disables the broadcast storm trap. You must also enable Broadcast Storm Recovery Mode (see the Switch Configuration… |
| 1.3.6.1.4.1.4526.11.1.2.7 | NodeagentSpanningTreeConfigGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.7.1 | ScalaragentSpanningTreeMode | read-write | current | The switch's Spanning Tree Switch Status |
| 1.3.6.1.4.1.4526.11.1.2.8 | NodeagentSwitchConfigGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.8.4 | TableagentSwitchAddressAgingTimeoutTable | not-accessible | current | The switch's address aging timeout table |
| 1.3.6.1.4.1.4526.11.1.2.8.4.1 | RowagentSwitchAddressAgingTimeoutEntry | not-accessible | current | Aging information about a specific Filtering Database. |
| 1.3.6.1.4.1.4526.11.1.2.8.4.1.1 | ColumnagentSwitchAddressAgingTimeout | read-write | current | The FDB entry's address aging timeout (in seconds) |
| 1.3.6.1.4.1.4526.11.1.2.8.5 | TableagentSwitchStaticMacFilteringTable | not-accessible | current | The switch's static Mac filtering table |
| 1.3.6.1.4.1.4526.11.1.2.8.5.1 | RowagentSwitchStaticMacFilteringEntry | not-accessible | current | Per-port ingress/egress filter configuration based on VLAN Id and MAC address. |
| 1.3.6.1.4.1.4526.11.1.2.8.5.1.1 | ColumnagentSwitchStaticMacFilteringVlanId | read-only | current | The Static MAC Filter Vlan Id |
| 1.3.6.1.4.1.4526.11.1.2.8.5.1.2 | ColumnagentSwitchStaticMacFilteringAddress | read-only | current | The Static MAC Filter MAC address |
| 1.3.6.1.4.1.4526.11.1.2.8.5.1.3 | ColumnagentSwitchStaticMacFilteringSourcePortMask | read-write | current | The Static MAC Filter source port mask. When setting this value, the system will ignore configuration for ports not between the first and last valid ports. Con… |
| 1.3.6.1.4.1.4526.11.1.2.8.5.1.4 | ColumnagentSwitchStaticMacFilteringDestPortMask | read-write | current | The Static MAC Filter destination port mask. When setting this value, the system will ignore configuration for ports not between the first and last valid ports… |
| 1.3.6.1.4.1.4526.11.1.2.8.5.1.5 | ColumnagentSwitchStaticMacFilteringStatus | read-create | current | The Static MAC Filter status. Supported values: active(1) - valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry |
| 1.3.6.1.4.1.4526.11.1.2.8.6 | NodeagentSwitchSnoopingGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.8.6.1 | TableagentSwitchSnoopingCfgTable | not-accessible | current | A table of the IGMP/MLD Snooping Global configuration entries. |
| 1.3.6.1.4.1.4526.11.1.2.8.6.1.1 | RowagentSwitchSnoopingCfgEntry | not-accessible | current | Represents entry for Snooping switch Configuration. |
| 1.3.6.1.4.1.4526.11.1.2.8.6.1.1.1 | ColumnagentSwitchSnoopingProtocol | read-only | current | The protocol type of network protocol in use. |
| 1.3.6.1.4.1.4526.11.1.2.8.6.1.1.2 | ColumnagentSwitchSnoopingAdminMode | read-write | current | This enables or disables Snooping on the system. |
| 1.3.6.1.4.1.4526.11.1.2.8.6.1.1.3 | ColumnagentSwitchSnoopingPortMask | read-write | current | IGMP/MLD Snooping Port Mask. This allows configuration of IGMP/MLD Snooping on selected ports. IGMP Snooping cannot be enabled on an interface that has routing… |
| 1.3.6.1.4.1.4526.11.1.2.8.6.1.1.4 | ColumnagentSwitchSnoopingMulticastControlFramesProcessed | read-only | current | Multicast Control Frames Processed by CPU. The number of multicast control frames that have been processed by the CPU. |
| 1.3.6.1.4.1.4526.11.1.2.8.7 | NodeagentSwitchSnoopingIntfGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.8.7.1 | TableagentSwitchSnoopingIntfTable | not-accessible | current | A table of the IGMP Snooping Interface configuration entries. |
| 1.3.6.1.4.1.4526.11.1.2.8.7.1.1 | RowagentSwitchSnoopingIntfEntry | not-accessible | current | Represents entry for a IGMP Snooping Interface. |
| 1.3.6.1.4.1.4526.11.1.2.8.7.1.1.1 | ColumnagentSwitchSnoopingIntfIndex | read-only | current | The port number to be selected. Each port maps to an interface. |
| 1.3.6.1.4.1.4526.11.1.2.8.7.1.1.2 | ColumnagentSwitchSnoopingIntfAdminMode | read-write | current | This enables or disables IGMP Snooping on a selected interface. |
| 1.3.6.1.4.1.4526.11.1.2.8.7.1.1.3 | ColumnagentSwitchSnoopingIntfGroupMembershipInterval | read-write | current | The amount of time in seconds that a switch will wait for a report from a particular group on the selected interface before deleting the interface from the ent… |
| 1.3.6.1.4.1.4526.11.1.2.8.7.1.1.4 | ColumnagentSwitchSnoopingIntfMaxResponseTime | read-write | current | The amount of time in seconds a switch will wait after sending a query on the selected interface because it did not receive a report for a particular group in … |
| 1.3.6.1.4.1.4526.11.1.2.8.7.1.1.5 | ColumnagentSwitchSnoopingIntfMRPExpirationTime | read-write | current | The amount of time in seconds that a switch will wait for a query to be received on the selected interface before the interface is removed from the list of int… |
| 1.3.6.1.4.1.4526.11.1.2.8.7.1.1.6 | ColumnagentSwitchSnoopingIntfFastLeaveAdminMode | read-write | current | This enables or disables IGMP Snooping on the selected interface. |
| 1.3.6.1.4.1.4526.11.1.2.8.7.1.1.7 | ColumnagentSwitchSnoopingIntfMulticastRouterMode | read-write | current | This enables or disables Multicast Routing on the selected interface. |
| 1.3.6.1.4.1.4526.11.1.2.8.7.1.1.8 | ColumnagentSwitchSnoopingIntfVlanIDs | read-only | current | This field lists all the VlanIDs which include the selected interface. |
| 1.3.6.1.4.1.4526.11.1.2.8.8 | NodeagentSwitchSnoopingVlanGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.8.8.1 | TableagentSwitchSnoopingVlanTable | not-accessible | current | A table of the IGMP Snooping Vlan configuration entries. |
| 1.3.6.1.4.1.4526.11.1.2.8.8.1.1 | RowagentSwitchSnoopingVlanEntry | not-accessible | current | Represents entry for a IGMP Snooping Vlan. |
| 1.3.6.1.4.1.4526.11.1.2.8.8.1.1.1 | ColumnagentSwitchSnoopingVlanAdminMode | read-write | current | This enables or disables IGMP Snooping on a selected Vlan interface. |
| 1.3.6.1.4.1.4526.11.1.2.8.8.1.1.2 | ColumnagentSwitchSnoopingVlanGroupMembershipInterval | read-write | current | The amount of time in seconds that a switch will wait for a report from a particular group on the selected vlan before deleting the interface participating in … |
| 1.3.6.1.4.1.4526.11.1.2.8.8.1.1.3 | ColumnagentSwitchSnoopingVlanMaxResponseTime | read-write | current | The amount of time in seconds a switch will wait after sending a query on the selected vlan because it did not receive a report for a particular group in the i… |
| 1.3.6.1.4.1.4526.11.1.2.8.8.1.1.4 | ColumnagentSwitchSnoopingVlanFastLeaveAdminMode | read-write | current | This enables or disables IGMP Snooping on the selected vlan. |
| 1.3.6.1.4.1.4526.11.1.2.8.8.1.1.5 | ColumnagentSwitchSnoopingVlanMRPExpirationTime | read-write | current | The amount of time in seconds that a switch will wait for a query to be received on the selected interface participating in the vlan before the interface is re… |
| 1.3.6.1.4.1.4526.11.1.2.8.9 | NodeagentSwitchVlanStaticMrouterGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.8.9.1 | TableagentSwitchVlanStaticMrouterTable | not-accessible | current | A table of the IGMP Static Mrouter Configuration parameters. |
| 1.3.6.1.4.1.4526.11.1.2.8.9.1.1 | RowagentSwitchVlanStaticMrouterEntry | not-accessible | current | Represents entry for a IGMP Static Mrouter. |
| 1.3.6.1.4.1.4526.11.1.2.8.9.1.1.1 | ColumnagentSwitchVlanStaticMrouterAdminMode | read-write | current | This enables or disables IGMP Mrouter on a per-interface per-vlan basis. |
| 1.3.6.1.4.1.4526.11.1.2.8.10 | NodeagentSwitchMFDBGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.8.10.1 | TableagentSwitchMFDBTable | not-accessible | current | The Multicast Forwarding Database table |
| 1.3.6.1.4.1.4526.11.1.2.8.10.1.1 | RowagentSwitchMFDBEntry | not-accessible | current | Contains Forwarding and Filtering information per Vlan Index, MAC Address, and Component User. |
| 1.3.6.1.4.1.4526.11.1.2.8.10.1.1.1 | ColumnagentSwitchMFDBVlanId | read-only | current | Vlan Index for which this entry is associated with. |
| 1.3.6.1.4.1.4526.11.1.2.8.10.1.1.2 | ColumnagentSwitchMFDBMacAddress | read-only | current | A multicast MAC address for which the switch has forwarding and or filtering information. |
| 1.3.6.1.4.1.4526.11.1.2.8.10.1.1.3 | ColumnagentSwitchMFDBProtocolType | read-only | current | The component that is responsible for this entry in the Multicast Forwarding Database. |
| 1.3.6.1.4.1.4526.11.1.2.8.10.1.1.4 | ColumnagentSwitchMFDBType | read-only | current | This displays the type of the entry. static(1) - Entries configured by the end user dynamic(2) - Entries added as a result of a learning process or protocol |
| 1.3.6.1.4.1.4526.11.1.2.8.10.1.1.5 | ColumnagentSwitchMFDBDescription | read-only | current | Text description of this multicast table entry. |
| 1.3.6.1.4.1.4526.11.1.2.8.10.1.1.6 | ColumnagentSwitchMFDBForwardingPortMask | read-only | current | BitMask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort … |
| 1.3.6.1.4.1.4526.11.1.2.8.10.1.1.7 | ColumnagentSwitchMFDBFilteringPortMask | read-only | current | BitMask indicating which ports this entry indicates should be filtered. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort a… |
| 1.3.6.1.4.1.4526.11.1.2.8.10.2 | TableagentSwitchMFDBSummaryTable | not-accessible | current | The Multicast Forwarding Database Summary table |
| 1.3.6.1.4.1.4526.11.1.2.8.10.2.1 | RowagentSwitchMFDBSummaryEntry | not-accessible | current | Summarizes the forwarding ports for all components registered for all MFDB table entries with the same Vlan Index and MAC Address. |
| 1.3.6.1.4.1.4526.11.1.2.8.10.2.1.1 | ColumnagentSwitchMFDBSummaryVlanId | read-only | current | Vlan Index for which this entry is associated with. |
| 1.3.6.1.4.1.4526.11.1.2.8.10.2.1.2 | ColumnagentSwitchMFDBSummaryMacAddress | read-only | current | A multicast MAC address for which the switch has forwarding and or filtering information. |
| 1.3.6.1.4.1.4526.11.1.2.8.10.2.1.3 | ColumnagentSwitchMFDBSummaryForwardingPortMask | read-only | current | Port Mask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePor… |
| 1.3.6.1.4.1.4526.11.1.2.8.10.3 | ScalaragentSwitchMFDBMaxTableEntries | read-only | current | This displays the maximum number of entries that can possibly be in the Multicast Forwarding Database table. |
| 1.3.6.1.4.1.4526.11.1.2.8.10.4 | ScalaragentSwitchMFDBMostEntriesUsed | read-only | current | This displays the largest number of entries that have been present in the Multicast Forwarding Database table. This value is also known as the MFDB high-water … |
| 1.3.6.1.4.1.4526.11.1.2.8.10.5 | ScalaragentSwitchMFDBCurrentEntries | read-only | current | This displays the current number of entries in the Multicast Forwarding Database table. |
| 1.3.6.1.4.1.4526.11.1.2.8.12 | NodeagentSwitchStormControlGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.8.12.1 | ScalaragentSwitchDot3FlowControlMode | read-write | current | Config switchconfig flowcontrol allows you to enable or disable 802.3x flow control for the switch. This value applies to only full-duplex mode ports. |
| 1.3.6.1.4.1.4526.11.1.2.8.12.4 | ScalaragentSwitchBroadcastControlMode | read-write | current | The switch config broadcast allows you to enable or disable broadcast storm recovery mode. When you specify Enable for Broadcast Storm Recovery and the broadca… |
| 1.3.6.1.4.1.4526.11.1.2.8.12.5 | ScalaragentSwitchBroadcastControlThreshold | read-write | current | Configures the broadcast storm recovery threshold for this port as a percentage of port speed. |
| 1.3.6.1.4.1.4526.11.1.2.8.12.6 | ScalaragentSwitchMulticastControlMode | read-write | current | The switch config multicast allows you to enable or disable multicast storm recovery mode. When you specify Enable for multicast Storm Recovery and the multica… |
| 1.3.6.1.4.1.4526.11.1.2.8.12.7 | ScalaragentSwitchMulticastControlThreshold | read-write | current | Configures the multicast storm recovery threshold for this port as a percentage of port speed. |
| 1.3.6.1.4.1.4526.11.1.2.8.12.8 | ScalaragentSwitchUnicastControlMode | read-write | current | The switch config unicast allows you to enable or disable unicast storm recovery mode. When you specify Enable for unicast Storm Recovery and the unknown unica… |
| 1.3.6.1.4.1.4526.11.1.2.8.12.9 | ScalaragentSwitchUnicastControlThreshold | read-write | current | Configures the unicast storm recovery threshold for this port as a percentage of port speed. |
| 1.3.6.1.4.1.4526.11.1.2.8.15 | NodeagentDhcpFilteringGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.8.15.1 | ScalaragentDhcpFilteringAdminMode | read-write | current | Dhcp Filtering mode: enable - enable dhcp filtering mode disable - disable dhcp filtering mode. |
| 1.3.6.1.4.1.4526.11.1.2.8.15.2 | TableagentDhcpFilteringPortConfigTable | not-accessible | current | A table that contains the configuration objects for the with each port. |
| 1.3.6.1.4.1.4526.11.1.2.8.15.2.1 | RowagentDhcpFilteringPortConfigEntry | not-accessible | current | The configuration information for Dhcp Filtering. |
| 1.3.6.1.4.1.4526.11.1.2.8.15.2.1.1 | ColumnagentDhcpFilteringPortTrustedMode | read-write | current | Port's DHCP mode. It can be either trusted or untrusted default will be untrusted. |
| 1.3.6.1.4.1.4526.11.1.2.8.18 | NodeagentSwitchProtectedPortConfigGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.8.18.1 | TableagentSwitchProtectedPortTable | not-accessible | current | The switch's protected port mapping table |
| 1.3.6.1.4.1.4526.11.1.2.8.18.1.1 | RowagentSwitchProtectedPortEntry | not-accessible | current | Protected ports assigned to groups. |
| 1.3.6.1.4.1.4526.11.1.2.8.18.1.1.1 | ColumnagentSwitchProtectedPortGroupId | not-accessible | current | The group that this port belongs to |
| 1.3.6.1.4.1.4526.11.1.2.8.18.1.1.2 | ColumnagentSwitchProtectedPortGroupName | read-write | current | The name of the group |
| 1.3.6.1.4.1.4526.11.1.2.8.18.1.1.3 | ColumnagentSwitchProtectedPortPortList | read-write | current | The set of ports that are protected in this group |
| 1.3.6.1.4.1.4526.11.1.2.8.20 | NodeagentSwitchSnoopingQuerierGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.8.20.1 | TableagentSwitchSnoopingQuerierCfgTable | not-accessible | current | A table of the IGMP/MLD Snooping Querier Global configuration entries. |
| 1.3.6.1.4.1.4526.11.1.2.8.20.1.1 | RowagentSwitchSnoopingQuerierCfgEntry | not-accessible | current | Represents entry for Snooping Querier Configuration. |
| 1.3.6.1.4.1.4526.11.1.2.8.20.1.1.1 | ColumnagentSwitchSnoopingQuerierAdminMode | read-write | current | This enables or disables Snooping Querier on the system. |
| 1.3.6.1.4.1.4526.11.1.2.8.20.1.1.2 | ColumnagentSwitchSnoopingQuerierVersion | read-write | current | This specifies the multicast protocol versions that are supported by the system. |
| 1.3.6.1.4.1.4526.11.1.2.8.20.1.1.3 | ColumnagentSwitchSnoopingQuerierAddress | read-write | current | This specifies the default source ip address to be used while generating general queries. |
| 1.3.6.1.4.1.4526.11.1.2.8.20.1.1.4 | ColumnagentSwitchSnoopingQuerierQueryInterval | read-write | current | This specified the timer interval after which the system generates general queries. |
| 1.3.6.1.4.1.4526.11.1.2.8.20.1.1.5 | ColumnagentSwitchSnoopingQuerierExpiryInterval | read-write | current | This specified the timer interval after which the detected other querier information is no longer valid. |
| 1.3.6.1.4.1.4526.11.1.2.8.20.2 | TableagentSwitchSnoopingQuerierVlanTable | not-accessible | current | A table of the Snooping Querier Vlan configuration entries. |
| 1.3.6.1.4.1.4526.11.1.2.8.20.2.1 | RowagentSwitchSnoopingQuerierVlanEntry | not-accessible | current | Represents entry for a Snooping Querier configurable Vlan. |
| 1.3.6.1.4.1.4526.11.1.2.8.20.2.1.1 | ColumnagentSwitchSnoopingQuerierVlanAdminMode | read-write | current | This enables or disables Snooping Querier on a selected Vlan interface. |
| 1.3.6.1.4.1.4526.11.1.2.8.20.2.1.2 | ColumnagentSwitchSnoopingQuerierVlanOperMode | read-only | current | This specifies the current state of the Snooping Querier on a selected vlan interface |
| 1.3.6.1.4.1.4526.11.1.2.8.20.2.1.3 | ColumnagentSwitchSnoopingQuerierElectionParticipateMode | read-write | current | This enables or disables the Snooping Querier Election Participation mode. When enabled snooping querier switch will participate in querier election up on disc… |
| 1.3.6.1.4.1.4526.11.1.2.8.20.2.1.4 | ColumnagentSwitchSnoopingQuerierVlanAddress | read-write | current | This specifies the default source ip address to be used while generating general queries on the specified vlan. |
| 1.3.6.1.4.1.4526.11.1.2.8.20.2.1.5 | ColumnagentSwitchSnoopingQuerierOperVersion | read-only | current | This specifies the multicast protocol version that is currently being used by the snooping switch for the specified vlan while generating query messages. |
| 1.3.6.1.4.1.4526.11.1.2.8.20.2.1.6 | ColumnagentSwitchSnoopingQuerierOperMaxResponseTime | read-only | current | The amount of time in seconds a switch will wait after sending a query on the selected vlan because it did not receive a report for a particular group in the i… |
| 1.3.6.1.4.1.4526.11.1.2.8.20.2.1.7 | ColumnagentSwitchSnoopingQuerierLastQuerierAddress | read-only | current | This specifies the last querier's ip address for the specified vlan. It represents the detected other multicast querier in the vlan. |
| 1.3.6.1.4.1.4526.11.1.2.8.20.2.1.8 | ColumnagentSwitchSnoopingQuerierLastQuerierVersion | read-only | current | This specifies the multicast protocol version that is currently being used by the detected other multicast querier for the specified vlan. |
| 1.3.6.1.4.1.4526.11.1.2.9 | NodeagentTransferConfigGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.9.1 | NodeagentTransferUploadGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.9.1.1 | ScalaragentTransferUploadMode | read-write | current | Transfer upload mode configures the mode to use when uploading from the switch. The mode is either X/Y/ZMODEM, TFTP, SFTP or SCP. X/Y/ZMODEM is valid only when… |
| 1.3.6.1.4.1.4526.11.1.2.9.1.2 | ScalaragentTransferUploadServerIP | read-write | deprecated | Transfer upload server IP configures the IP address of the server where the file is located. It is valid only when the Transfer Mode is TFTP, SFTP, or SCP. The… |
| 1.3.6.1.4.1.4526.11.1.2.9.1.3 | ScalaragentTransferUploadPath | read-write | current | Transfer upload path configures the directory path where the file is to be uploaded to. The switch remembers the last file path used. |
| 1.3.6.1.4.1.4526.11.1.2.9.1.4 | ScalaragentTransferUploadFilename | read-write | current | Transfer upload filename configures the file name for the file being uploaded from the switch. It can be up to 32 alphanumeric characters. The switch remembers… |
| 1.3.6.1.4.1.4526.11.1.2.9.1.5 | ScalaragentTransferUploadDataType | read-write | current | Transfer upload datatype configures the type of file to upload from the switch. The types for upload are: - Configuration File - Error log - Message log - Trap… |
| 1.3.6.1.4.1.4526.11.1.2.9.1.6 | ScalaragentTransferUploadStart | read-write | current | Transfer upload start will start an upload transfer. The agentTransferUploadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a tra… |
| 1.3.6.1.4.1.4526.11.1.2.9.1.7 | ScalaragentTransferUploadStatus | read-only | current | Indicates the current status of an upload transfer. |
| 1.3.6.1.4.1.4526.11.1.2.9.1.8 | ScalaragentTransferUploadServerAddressType | read-write | current | The type of the serverip address, as defined in the InetAddress MIB. The agentTransferUploadServerAddress object is intepreted within the context of agentTrans… |
| 1.3.6.1.4.1.4526.11.1.2.9.1.9 | ScalaragentTransferUploadServerAddress | read-write | current | Transfer upload serverip configures the IP address of the server where the file is to be uploaded to.It is valid only when the Transfer Mode is TFTP, SFTP or S… |
| 1.3.6.1.4.1.4526.11.1.2.9.1.10 | ScalaragentTransferUploadImagename | read-write | current | Transfer upload image name. Sets the image to be uploaded as the specified name Note: Imagename, File Name, File Path, and Server IP Address are applicable onl… |
| 1.3.6.1.4.1.4526.11.1.2.9.1.11 | ScalaragentTransferUploadUsername | read-write | current | Username applicable only to secure upload types, i.e., SFTP or SCP. |
| 1.3.6.1.4.1.4526.11.1.2.9.1.12 | ScalaragentTransferUploadPassword | read-write | current | Password applicable only to secure upload types, i.e. SFTP or SCP. |
| 1.3.6.1.4.1.4526.11.1.2.9.2 | NodeagentTransferDownloadGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.9.2.1 | ScalaragentTransferDownloadMode | read-write | current | Transfer download mode configures the mode to use when downloading to the switch. The mode is either X/Y/ZMODEM, TFTP, SFTP or SCP. X/Y/ZMODEM is valid only wh… |
| 1.3.6.1.4.1.4526.11.1.2.9.2.2 | ScalaragentTransferDownloadServerIP | read-write | deprecated | Transfer download serverip configures the IP address of the server where the file is located. It is valid only when the Transfer Mode is TFTP, SFTP or SCP. The… |
| 1.3.6.1.4.1.4526.11.1.2.9.2.3 | ScalaragentTransferDownloadPath | read-write | current | Transfer download path configures the directory path where the file is located. The switch remembers the last file path used. |
| 1.3.6.1.4.1.4526.11.1.2.9.2.4 | ScalaragentTransferDownloadFilename | read-write | current | Transfer download filename configures the file name for the file being downloaded to the switch. It can be up to 32 alphanumeric characters. The switch remembe… |
| 1.3.6.1.4.1.4526.11.1.2.9.2.5 | ScalaragentTransferDownloadDataType | read-write | current | Transfer download datatype configures the type of file to download to the switch. The types for download are: code - Code File config - Configuration File sshk… |
| 1.3.6.1.4.1.4526.11.1.2.9.2.6 | ScalaragentTransferDownloadStart | read-write | current | Transfer download start will start an download transfer. The agentTransferDownloadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate… |
| 1.3.6.1.4.1.4526.11.1.2.9.2.7 | ScalaragentTransferDownloadStatus | read-only | current | Indicates the current status of an download transfer. |
| 1.3.6.1.4.1.4526.11.1.2.9.2.8 | ScalaragentTransferDownloadServerAddressType | read-write | current | The type of the serverip address, as defined in the InetAddress MIB. The agentTransferDownloadServerAddress object is intepreted within the context of agentTra… |
| 1.3.6.1.4.1.4526.11.1.2.9.2.9 | ScalaragentTransferDownloadServerAddress | read-write | current | Transfer download serverip configures the IP address of the server where the file is to be downloaded from.It is valid only when the Transfer Mode is TFTP, SFT… |
| 1.3.6.1.4.1.4526.11.1.2.9.2.10 | ScalaragentTransferDownloadImagename | read-write | current | Transfer download image name. Sets the downloaded image as the specified name Note: Imagename, File Name, File Path, and Server IP Address are applicable only … |
| 1.3.6.1.4.1.4526.11.1.2.9.2.11 | ScalaragentTransferDownloadUsername | read-write | current | Username applicable only to secure download types, i.e., SFTP or SCP. |
| 1.3.6.1.4.1.4526.11.1.2.9.2.12 | ScalaragentTransferDownloadPassword | read-write | current | Password applicable only to secure download types, i.e. SFTP or SCP. |
| 1.3.6.1.4.1.4526.11.1.2.9.3 | NodeagentImageConfigGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.9.3.1 | ScalaragentImage1 | read-only | current | The image1 softwate version . |
| 1.3.6.1.4.1.4526.11.1.2.9.3.2 | ScalaragentImage2 | read-only | current | The image2 software version. |
| 1.3.6.1.4.1.4526.11.1.2.9.3.3 | ScalaragentActiveImage | read-only | current | The active image name. image1 or image2. |
| 1.3.6.1.4.1.4526.11.1.2.9.3.4 | ScalaragentNextActiveImage | read-write | current | The next active image name. user assigns either image1 or image2. |
| 1.3.6.1.4.1.4526.11.1.2.10 | NodeagentPortMirroringGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.10.1 | ScalaragentMirroredPortIfIndex | read-write | obsolete | IfIndex of the mirrored port |
| 1.3.6.1.4.1.4526.11.1.2.10.2 | ScalaragentProbePortIfIndex | read-write | obsolete | IfIndex of the probe port |
| 1.3.6.1.4.1.4526.11.1.2.10.3 | ScalaragentPortMirroringMode | read-write | obsolete | Port mirroring mode: enable - enable mirroring mode disable - disable mirroring mode delete - clear MirroredPort and Probe Port configuration |
| 1.3.6.1.4.1.4526.11.1.2.10.4 | TableagentPortMirrorTable | not-accessible | current | This table includes entries for each Port Mirroring session. |
| 1.3.6.1.4.1.4526.11.1.2.10.4.1 | RowagentPortMirrorEntry | not-accessible | current | Provides configuration of a Port Mirroring session specifying the destination port, and the source Port Mask, providing a many-to-one mapping. |
| 1.3.6.1.4.1.4526.11.1.2.10.4.1.1 | ColumnagentPortMirrorSessionNum | not-accessible | current | The Session number of this mirroring entry. The number of sessions is fixed, and is platform dependant. |
| 1.3.6.1.4.1.4526.11.1.2.10.4.1.2 | ColumnagentPortMirrorDestinationPort | read-write | current | The port which traffic from the mirrored ports will be sent to. |
| 1.3.6.1.4.1.4526.11.1.2.10.4.1.3 | ColumnagentPortMirrorSourcePortMask | read-write | current | The ports from which traffic will be sent to the destination port. The destination port can not be included in this list of ports. |
| 1.3.6.1.4.1.4526.11.1.2.10.4.1.4 | ColumnagentPortMirrorAdminMode | read-write | current | The status of this port mirroring session. enable(1) - This session is active and all traffic from the source ports will be mirrored to the destination port. d… |
| 1.3.6.1.4.1.4526.11.1.2.10.5 | TableagentPortMirrorTypeTable | not-accessible | current | This table includes entries for each source port's direction of port mirroring. |
| 1.3.6.1.4.1.4526.11.1.2.10.5.1 | RowagentPortMirrorTypeEntry | not-accessible | current | Provides configuration of a Port Mirroring direction specifying the session of the port mirroring and source port |
| 1.3.6.1.4.1.4526.11.1.2.10.5.1.1 | ColumnagentPortMirrorTypeSourcePort | not-accessible | current | The port from which traffic will be sent to the destination port. This port should be a source port in the corresponding session |
| 1.3.6.1.4.1.4526.11.1.2.10.5.1.2 | ColumnagentPortMirrorTypeType | read-write | current | The direction of the data to be mirrored on this source port. tx(1) - The data that is transmitted from the source port. rx(2) - The data that is received on t… |
| 1.3.6.1.4.1.4526.11.1.2.12 | TableagentDot3adAggPortTable | not-accessible | current | This table provides 802.3ad link aggregation information for each physical port that is not available through the standard MIB. |
| 1.3.6.1.4.1.4526.11.1.2.12.1 | RowagentDot3adAggPortEntry | not-accessible | current | Information about a table entry. The agentDot3adAggPort identifies the external interface number of the port. |
| 1.3.6.1.4.1.4526.11.1.2.12.1.1 | ColumnagentDot3adAggPort | read-only | current | ifIndex of this physical port |
| 1.3.6.1.4.1.4526.11.1.2.12.1.2 | ColumnagentDot3adAggPortLACPMode | read-write | current | Enable/disable 802.3ad LACP on this port |
| 1.3.6.1.4.1.4526.11.1.2.13 | TableagentPortConfigTable | not-accessible | current | A table of the switch's physical port config entries |
| 1.3.6.1.4.1.4526.11.1.2.13.1 | RowagentPortConfigEntry | not-accessible | current | Switch's physical port config entry |
| 1.3.6.1.4.1.4526.11.1.2.13.1.1 | ColumnagentPortDot1dBasePort | read-only | current | The port number of this port. |
| 1.3.6.1.4.1.4526.11.1.2.13.1.2 | ColumnagentPortIfIndex | read-only | current | The switch's Port IfIndex |
| 1.3.6.1.4.1.4526.11.1.2.13.1.3 | ColumnagentPortIanaType | read-only | current | The switch's Port Type |
| 1.3.6.1.4.1.4526.11.1.2.13.1.4 | ColumnagentPortSTPMode | read-write | current | The switch's Port Spanning Tree Protocol Mode STP mode values are: dot1d (the default) fast, indicates you want to use the fast spanning tree mode off, indicat… |
| 1.3.6.1.4.1.4526.11.1.2.13.1.5 | ColumnagentPortSTPState | read-only | current | The switch's Port Spanning Tree Protocol State. This object is only supported when the Dot1d Protocol is enabled. |
| 1.3.6.1.4.1.4526.11.1.2.13.1.6 | ColumnagentPortAdminMode | read-write | current | The switch's Port Admin Mode |
| 1.3.6.1.4.1.4526.11.1.2.13.1.7 | ColumnagentPortPhysicalMode | read-write | obsolete | The switch's Port Speed Mode. This is the configured physical mode. This object is read-only for gigabit ports |
| 1.3.6.1.4.1.4526.11.1.2.13.1.8 | ColumnagentPortPhysicalStatus | read-only | obsolete | The switch's Port Physical Speed Status. This is the current actual speed. |
| 1.3.6.1.4.1.4526.11.1.2.13.1.9 | ColumnagentPortLinkTrapMode | read-write | current | If enabled, link up and link down traps will be sent for this port. |
| 1.3.6.1.4.1.4526.11.1.2.13.1.10 | ColumnagentPortClearStats | read-write | current | clear stats for this port only |
| 1.3.6.1.4.1.4526.11.1.2.13.1.11 | ColumnagentPortDefaultType | read-write | current | This object identifies the default administrative port type, to be used in conjunction with the operational port type denoted by agentPortType. The set of poss… |
| 1.3.6.1.4.1.4526.11.1.2.13.1.13 | ColumnagentPortAutoNegAdminStatus | read-write | current | This object identifies the administration status of auto negotiation for this port. |
| 1.3.6.1.4.1.4526.11.1.2.13.1.14 | ColumnagentPortDot3FlowControlMode | read-write | current | Config flowcontrol allows you to enable or disable 802.3x flow control for this port. This value applies to only full-duplex mode ports. |
| 1.3.6.1.4.1.4526.11.1.2.13.1.18 | ColumnagentPortMaxFrameSizeLimit | read-only | current | This object identifies the largest value that can be configured for agentPortMaxFrameSize |
| 1.3.6.1.4.1.4526.11.1.2.13.1.19 | ColumnagentPortMaxFrameSize | read-write | current | This object identifies the currently configured maximum frame size value for this port. The maximmum value that this object can be set to is the value of agent… |
| 1.3.6.1.4.1.4526.11.1.2.13.1.20 | ColumnagentPortBroadcastControlMode | read-write | current | If enabled, broadcast storm recovery will function on this port. When you specify Enable for Broadcast Storm Recovery and the broadcast traffic on this Etherne… |
| 1.3.6.1.4.1.4526.11.1.2.13.1.21 | ColumnagentPortBroadcastControlThreshold | read-write | current | Configures the broadcast storm recovery threshold for this port as a percentage of port speed. |
| 1.3.6.1.4.1.4526.11.1.2.13.1.22 | ColumnagentPortMulticastControlMode | read-write | current | If enabled, multicast storm recovery will function on this port. When you specify Enable for Multicast Storm Recovery and the multicast traffic on this Etherne… |
| 1.3.6.1.4.1.4526.11.1.2.13.1.23 | ColumnagentPortMulticastControlThreshold | read-write | current | Configures the multicast storm recovery threshold for this port as a percentage of port speed. |
| 1.3.6.1.4.1.4526.11.1.2.13.1.24 | ColumnagentPortUnicastControlMode | read-write | current | If enabled, unicast storm recovery will function on this port. When you specify Enable for Unicast Storm Recovery and the unknown unicast traffic on this Ether… |
| 1.3.6.1.4.1.4526.11.1.2.13.1.25 | ColumnagentPortUnicastControlThreshold | read-write | current | Configures the unicast storm recovery threshold for this port as a percentage of port speed. |
| 1.3.6.1.4.1.4526.11.1.2.15 | NodeagentStpSwitchConfigGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.15.1 | ScalaragentStpConfigDigestKey | read-only | current | The MST configuration digest key. |
| 1.3.6.1.4.1.4526.11.1.2.15.2 | ScalaragentStpConfigFormatSelector | read-only | current | The MST configuration format selector. A value other than 0 (zero) indicates non-support for the IEEE 802.1s standard. |
| 1.3.6.1.4.1.4526.11.1.2.15.3 | ScalaragentStpConfigName | read-write | current | The MST configuration name of at most 32 characters. |
| 1.3.6.1.4.1.4526.11.1.2.15.4 | ScalaragentStpConfigRevision | read-write | current | The MST configuration revision. The default value is 1. |
| 1.3.6.1.4.1.4526.11.1.2.15.5 | ScalaragentStpForceVersion | read-write | current | The MST configuration force protocol version. The default version is dot1s. |
| 1.3.6.1.4.1.4526.11.1.2.15.6 | ScalaragentStpAdminMode | read-write | current | The spanning tree operational status. enable(1) - enables spanning tree operational status on the switch. disable(2) - disables spanning tree operational statu… |
| 1.3.6.1.4.1.4526.11.1.2.15.7 | ScalaragentStpBpduGuardMode | read-write | current | The spanning tree BPDU Guard Mode. enable(1) - enables BPDU Guard Mode on the switch. disable(2) - disables BPDU Guard Mode on the switch. The default status i… |
| 1.3.6.1.4.1.4526.11.1.2.15.8 | ScalaragentStpBpduFilterDefault | read-write | current | The spanning tree BPDU Filter Mode, it enables BPDU Filter on all edge ports. enable(1) - enables BPDU Filter Mode on the switch. disable(2) - disables BPDU Fi… |
| 1.3.6.1.4.1.4526.11.1.2.15.9 | TableagentStpPortTable | not-accessible | current | STP port table. |
| 1.3.6.1.4.1.4526.11.1.2.15.9.1 | RowagentStpPortEntry | not-accessible | current | STP port entry. |
| 1.3.6.1.4.1.4526.11.1.2.15.9.1.1 | ColumnagentStpPortState | read-write | current | The administrative STP state for the port. enable(1) - enables STP on the port. disable(2) - disables STP on the port. The default port STP state is enabled fo… |
| 1.3.6.1.4.1.4526.11.1.2.15.9.1.2 | ColumnagentStpPortStatsMstpBpduRx | read-only | current | The MSTP BPDUs received on a specific port. |
| 1.3.6.1.4.1.4526.11.1.2.15.9.1.3 | ColumnagentStpPortStatsMstpBpduTx | read-only | current | The MSTP BPDUs sent from a specific port. |
| 1.3.6.1.4.1.4526.11.1.2.15.9.1.4 | ColumnagentStpPortStatsRstpBpduRx | read-only | current | The RSTP BPDUs received on a specific port. |
| 1.3.6.1.4.1.4526.11.1.2.15.9.1.5 | ColumnagentStpPortStatsRstpBpduTx | read-only | current | The RSTP BPDUs sent from a specific port. |
| 1.3.6.1.4.1.4526.11.1.2.15.9.1.6 | ColumnagentStpPortStatsStpBpduRx | read-only | current | The STP BPDUs received on a specific port. |
| 1.3.6.1.4.1.4526.11.1.2.15.9.1.7 | ColumnagentStpPortStatsStpBpduTx | read-only | current | The STP BPDUs sent from a specific port. |
| 1.3.6.1.4.1.4526.11.1.2.15.9.1.8 | ColumnagentStpPortUpTime | read-only | current | Time since port was reset. It is displayed in days, hours, minutes, and seconds. |
| 1.3.6.1.4.1.4526.11.1.2.15.9.1.9 | ColumnagentStpPortMigrationCheck | read-write | current | Force the specified port to transmit RSTP or MSTP BPDU's. Supported values: false(0) - BPDUs are not to be transmitted. true(1) - BPDUs are to be transmitted A… |
| 1.3.6.1.4.1.4526.11.1.2.15.9.1.10 | ColumnagentStpPortHelloTime | read-write | current | Hello time for the STP port. The default value is 2. |
| 1.3.6.1.4.1.4526.11.1.2.15.10 | NodeagentStpCstConfigGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.15.10.1 | ScalaragentStpCstHelloTime | read-only | current | The MSTP root port hello time for the CIST. |
| 1.3.6.1.4.1.4526.11.1.2.15.10.2 | ScalaragentStpCstMaxAge | read-only | current | The MSTP root port max age for the CIST. |
| 1.3.6.1.4.1.4526.11.1.2.15.10.3 | ScalaragentStpCstRegionalRootId | read-only | current | The MSTP regional root identifier for the CIST. |
| 1.3.6.1.4.1.4526.11.1.2.15.10.4 | ScalaragentStpCstRegionalRootPathCost | read-only | current | The MSTP regional root path cost for the CIST. |
| 1.3.6.1.4.1.4526.11.1.2.15.10.5 | ScalaragentStpCstRootFwdDelay | read-only | current | The MSTP root port forward delay for the CIST. |
| 1.3.6.1.4.1.4526.11.1.2.15.10.6 | ScalaragentStpCstBridgeFwdDelay | read-write | current | The MSTP bridge forward delay for the CIST. The default value is 15. |
| 1.3.6.1.4.1.4526.11.1.2.15.10.7 | ScalaragentStpCstBridgeHelloTime | read-only | current | The MSTP bridge hello time for the CIST. The default value is 2. According to IEEE 802.1Q-REV 2005 updating hello time is disallowed |
| 1.3.6.1.4.1.4526.11.1.2.15.10.8 | ScalaragentStpCstBridgeHoldTime | read-only | current | The MSTP bridge hold time for the CIST. |
| 1.3.6.1.4.1.4526.11.1.2.15.10.9 | ScalaragentStpCstBridgeMaxAge | read-write | current | The MSTP bridge max age for the CIST. The default value is 20. |
| 1.3.6.1.4.1.4526.11.1.2.15.10.10 | ScalaragentStpCstBridgeMaxHops | read-write | current | The MSTP bridge max hops for the CIST. The default value is 20. |
| 1.3.6.1.4.1.4526.11.1.2.15.10.11 | ScalaragentStpCstBridgePriority | read-write | current | The MSTP bridge priority for the CIST. The default value is 32768. |
| 1.3.6.1.4.1.4526.11.1.2.15.10.12 | ScalaragentStpCstBridgeHoldCount | read-write | current | The MSTP bridge hold count for the CIST. This command sets the value of maximum bpdus that a bridge is allowed to send within a hello time window. The default … |
| 1.3.6.1.4.1.4526.11.1.2.15.10.13 | ScalaragentStpCstTimeSinceTopologyChange | read-only | current | The MSTP time since the last topology change for the CIST. |
| 1.3.6.1.4.1.4526.11.1.2.15.10.14 | ScalaragentStpCstTopologyChangeCount | read-only | current | The MSTP count of topology changes for the CIST. |
| 1.3.6.1.4.1.4526.11.1.2.15.11 | TableagentStpCstPortTable | not-accessible | current | CIST port table. |
| 1.3.6.1.4.1.4526.11.1.2.15.11.1 | RowagentStpCstPortEntry | not-accessible | current | CIST port entry. |
| 1.3.6.1.4.1.4526.11.1.2.15.11.1.1 | ColumnagentStpCstPortOperEdge | read-only | current | The MSTP operational status of a specific port for the CIST. |
| 1.3.6.1.4.1.4526.11.1.2.15.11.1.2 | ColumnagentStpCstPortOperPointToPoint | read-only | current | The MSTP operational point to point mac of a specific port for the CIST. |
| 1.3.6.1.4.1.4526.11.1.2.15.11.1.3 | ColumnagentStpCstPortTopologyChangeAck | read-only | current | The MSTP topology change acknowledge for a specific port in the CIST. |
| 1.3.6.1.4.1.4526.11.1.2.15.11.1.4 | ColumnagentStpCstPortEdge | read-write | current | The administrative state of a specific port in CIST. enable(1) - enables the port. disable(2) - disables the port. The default port state is disabled. |
| 1.3.6.1.4.1.4526.11.1.2.15.11.1.5 | ColumnagentStpCstPortForwardingState | read-only | current | The MSTP forwarding state of a specific port in CIST. |
| 1.3.6.1.4.1.4526.11.1.2.15.11.1.6 | ColumnagentStpCstPortId | read-only | current | The MSTP port identifier of a specific port in CIST. |
| 1.3.6.1.4.1.4526.11.1.2.15.11.1.7 | ColumnagentStpCstPortPathCost | read-write | current | The MSTP port path cost in CIST. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link s… |
| 1.3.6.1.4.1.4526.11.1.2.15.11.1.8 | ColumnagentStpCstPortPriority | read-write | current | The MSTP port priority in CIST. The priority is in the increments of 16. The default value is 128. |
| 1.3.6.1.4.1.4526.11.1.2.15.11.1.9 | ColumnagentStpCstDesignatedBridgeId | read-only | current | The MSTP designated bridge ID of a specific port in CIST. |
| 1.3.6.1.4.1.4526.11.1.2.15.11.1.10 | ColumnagentStpCstDesignatedCost | read-only | current | The MSTP designated cost of a specific port in CIST. |
| 1.3.6.1.4.1.4526.11.1.2.15.11.1.11 | ColumnagentStpCstDesignatedPortId | read-only | current | The MSTP designated port ID of a specific port in CIST. |
| 1.3.6.1.4.1.4526.11.1.2.15.11.1.12 | ColumnagentStpCstExtPortPathCost | read-write | current | The MSTP external port path cost in CIST. The default value varies depending upon the link speed. |
| 1.3.6.1.4.1.4526.11.1.2.15.11.1.13 | ColumnagentStpCstPortBpduGuardEffect | read-only | current | BPDU Guard Mode effect on the port. enable(1) - BPDU Guard Mode is enabled on the port. disable(2) - BPDU Guard Mode is disabled on the port. |
| 1.3.6.1.4.1.4526.11.1.2.15.11.1.14 | ColumnagentStpCstPortBpduFilter | read-write | current | This command sets BPDU Filter mode on the port. enable(1) - BPDU Filter Mode is enabled on the port. disable(2) - BPDU Filter Mode is disabled on the port. |
| 1.3.6.1.4.1.4526.11.1.2.15.11.1.15 | ColumnagentStpCstPortBpduFlood | read-write | current | This command sets BPDU Flood mode on the port. enable(1) - BPDU Flood Mode is enabled on the port. disable(2) - BPDU Flood Mode is disabled on the port. |
| 1.3.6.1.4.1.4526.11.1.2.15.11.1.16 | ColumnagentStpCstPortAutoEdge | read-write | current | This command sets the auto-edge mode of the port which enables it to become an edge port if it does not see BPDUs for some duration. enable(1) - enables the au… |
| 1.3.6.1.4.1.4526.11.1.2.15.11.1.17 | ColumnagentStpCstPortRootGuard | read-write | current | This command sets a port to discard any superior information received by the port and thus protect against root of the device from changing.The port gets put i… |
| 1.3.6.1.4.1.4526.11.1.2.15.11.1.18 | ColumnagentStpCstPortTCNGuard | read-write | current | This command restricts the port from propagating any topology change information received through that port. enable(1) - enables the tcn-guard mode for the por… |
| 1.3.6.1.4.1.4526.11.1.2.15.12 | TableagentStpMstTable | not-accessible | current | MST table. |
| 1.3.6.1.4.1.4526.11.1.2.15.12.1 | RowagentStpMstEntry | not-accessible | current | MST entry. |
| 1.3.6.1.4.1.4526.11.1.2.15.12.1.1 | ColumnagentStpMstId | read-only | current | The MSTP instance ID. |
| 1.3.6.1.4.1.4526.11.1.2.15.12.1.2 | ColumnagentStpMstBridgePriority | read-write | current | The MSTP bridge priority in a specific instance. The priority is in the increments of 4096. The recommended default value is 32768. |
| 1.3.6.1.4.1.4526.11.1.2.15.12.1.3 | ColumnagentStpMstBridgeIdentifier | read-only | current | The MSTP bridge identifier in a specific instance. |
| 1.3.6.1.4.1.4526.11.1.2.15.12.1.4 | ColumnagentStpMstDesignatedRootId | read-only | current | The MSTP designated root bridge identifier in a specific instance. |
| 1.3.6.1.4.1.4526.11.1.2.15.12.1.5 | ColumnagentStpMstRootPathCost | read-only | current | The MSTP root path cost in a specific instance. |
| 1.3.6.1.4.1.4526.11.1.2.15.12.1.6 | ColumnagentStpMstRootPortId | read-only | current | The MSTP root port ID in a specific instance. |
| 1.3.6.1.4.1.4526.11.1.2.15.12.1.7 | ColumnagentStpMstTimeSinceTopologyChange | read-only | current | The MSTP time since the last topology change in a specific instance. |
| 1.3.6.1.4.1.4526.11.1.2.15.12.1.8 | ColumnagentStpMstTopologyChangeCount | read-only | current | The MSTP count of topology changes in a specific instance. |
| 1.3.6.1.4.1.4526.11.1.2.15.12.1.9 | ColumnagentStpMstTopologyChangeParm | read-only | current | The MSTP topology change parameter in a specific instance. |
| 1.3.6.1.4.1.4526.11.1.2.15.12.1.10 | ColumnagentStpMstRowStatus | read-create | current | The MSTP instance status. Supported values: active(1) - valid instance. createAndGo(4) - used to create a new instance. destroy(6) - removes an instance. |
| 1.3.6.1.4.1.4526.11.1.2.15.13 | TableagentStpMstPortTable | not-accessible | current | MST port table. |
| 1.3.6.1.4.1.4526.11.1.2.15.13.1 | RowagentStpMstPortEntry | not-accessible | current | MST port entry. |
| 1.3.6.1.4.1.4526.11.1.2.15.13.1.1 | ColumnagentStpMstPortForwardingState | read-only | current | The MSTP forwarding state of a specific port in a specific instance. |
| 1.3.6.1.4.1.4526.11.1.2.15.13.1.2 | ColumnagentStpMstPortId | read-only | current | The MSTP port identifier of a specific port in a specific instance. |
| 1.3.6.1.4.1.4526.11.1.2.15.13.1.3 | ColumnagentStpMstPortPathCost | read-write | current | The MSTP port path cost in a specific instance. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depend… |
| 1.3.6.1.4.1.4526.11.1.2.15.13.1.4 | ColumnagentStpMstPortPriority | read-write | current | The MSTP port priority in a specific instance. The priority is in the increments of 16. The default value is 128. |
| 1.3.6.1.4.1.4526.11.1.2.15.13.1.5 | ColumnagentStpMstDesignatedBridgeId | read-only | current | The MSTP designated bridge ID of a specific port in a specific instance. |
| 1.3.6.1.4.1.4526.11.1.2.15.13.1.6 | ColumnagentStpMstDesignatedCost | read-only | current | The MSTP designated cost of a specific port in a specific instance. |
| 1.3.6.1.4.1.4526.11.1.2.15.13.1.7 | ColumnagentStpMstDesignatedPortId | read-only | current | The MSTP designated port ID of a specific port in a specific instance. |
| 1.3.6.1.4.1.4526.11.1.2.15.14 | TableagentStpMstVlanTable | not-accessible | current | MST VLAN table. |
| 1.3.6.1.4.1.4526.11.1.2.15.14.1 | RowagentStpMstVlanEntry | not-accessible | current | MST VLAN entry. |
| 1.3.6.1.4.1.4526.11.1.2.15.14.1.1 | ColumnagentStpMstVlanRowStatus | read-create | current | The association status of an MSTP instance and a VLAN. Supported values: active(1) - valid association between an MSTP instance and a VLAN. createAndGo(4) - us… |
| 1.3.6.1.4.1.4526.11.1.2.16 | NodeagentAuthenticationGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.16.1 | ScalaragentAuthenticationListCreate | read-write | current | Authentication List Create If set to a non empty string, creates a new Authentication List for configuration. |
| 1.3.6.1.4.1.4526.11.1.2.16.2 | TableagentAuthenticationListTable | not-accessible | current | MST VLAN table. |
| 1.3.6.1.4.1.4526.11.1.2.16.2.1 | RowagentAuthenticationListEntry | not-accessible | current | MST VLAN entry. |
| 1.3.6.1.4.1.4526.11.1.2.16.2.1.1 | ColumnagentAuthenticationListIndex | not-accessible | current | Authenticaiton List Index Unique number used for indexing into this table. |
| 1.3.6.1.4.1.4526.11.1.2.16.2.1.2 | ColumnagentAuthenticationListName | read-only | current | Authenticaiton List Name Unique name used to identify the Authentication List from other tables. |
| 1.3.6.1.4.1.4526.11.1.2.16.2.1.3 | ColumnagentAuthenticationListMethod1 | read-write | current | Authenticion List Method 1 Configures the first authentication method to use when this list is specified. |
| 1.3.6.1.4.1.4526.11.1.2.16.2.1.4 | ColumnagentAuthenticationListMethod2 | read-write | current | Authenticion List Method 2 Configures the second authentication method to use when this list is specified. |
| 1.3.6.1.4.1.4526.11.1.2.16.2.1.5 | ColumnagentAuthenticationListMethod3 | read-write | current | Authenticion List Method 3 Configures the third authentication method to use when this list is specified. |
| 1.3.6.1.4.1.4526.11.1.2.16.2.1.6 | ColumnagentAuthenticationListStatus | read-write | current | The status of the Authentication List. Supported values: active(1) - indicates a valid Authenticaiton List destroy(6) - removes the Authentication List. |
| 1.3.6.1.4.1.4526.11.1.2.16.2.1.7 | ColumnagentAuthenticationListMethod4 | read-write | current | Authenticion List Method 4 Configures the fourth authentication method to use when this list is specified. |
| 1.3.6.1.4.1.4526.11.1.2.16.3 | ScalaragentUserConfigDefaultAuthenticationList | read-write | current | Default Authentication List This object configures which authentication list to use for users which do not have an Authentication List configured. The list mus… |
| 1.3.6.1.4.1.4526.11.1.2.16.4 | TableagentUserAuthenticationConfigTable | not-accessible | current | User Authentication Config Table |
| 1.3.6.1.4.1.4526.11.1.2.16.4.1 | RowagentUserAuthenticationConfigEntry | not-accessible | current | User Authentication Config Entry |
| 1.3.6.1.4.1.4526.11.1.2.16.4.1.1 | ColumnagentUserAuthenticationList | read-write | current | User Authentication List This object configures which authentication list to use for this user. The list must be configured before setting. |
| 1.3.6.1.4.1.4526.11.1.2.16.5 | TableagentUserPortConfigTable | not-accessible | current | User Port Config Table |
| 1.3.6.1.4.1.4526.11.1.2.16.5.1 | RowagentUserPortConfigEntry | not-accessible | current | User Port Config Entry |
| 1.3.6.1.4.1.4526.11.1.2.16.5.1.1 | ColumnagentUserPortSecurity | read-write | current | User Port Port Security This object configures which ports the user has access to. Ports are indexed based on dot1dBasePort entries in dot1dBasePortTable. |
| 1.3.6.1.4.1.4526.11.1.2.17 | NodeagentClassOfServiceGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.17.1 | TableagentClassOfServicePortTable | not-accessible | current | A table that contains information about the 802.1p priority mapping to traffic class priority queue for every physical port. |
| 1.3.6.1.4.1.4526.11.1.2.17.1.1 | RowagentClassOfServicePortEntry | not-accessible | current | A 802.1p priority mapped to a traffic class priority queue. |
| 1.3.6.1.4.1.4526.11.1.2.17.1.1.1 | ColumnagentClassOfServicePortPriority | not-accessible | current | The Priority value determined for the received frame. This value is equivalent to the priority indicated in the tagged frame received, or one of the evaluated … |
| 1.3.6.1.4.1.4526.11.1.2.17.1.1.2 | ColumnagentClassOfServicePortClass | read-write | current | Traffic class priority queue the received frame is mapped to. |
| 1.3.6.1.4.1.4526.11.1.2.18 | NodeagentHTTPConfigGroup | |||
| 1.3.6.1.4.1.4526.11.1.2.18.1 | ScalaragentHTTPWebMode | read-write | current | Configures the HTTP server admin mode |
| 1.3.6.1.4.1.4526.11.1.2.18.2 | ScalaragentHTTPJavaMode | read-write | current | Configures the use of the Java interface through Web connections. |
| 1.3.6.1.4.1.4526.11.1.2.18.3 | ScalaragentHTTPMaxSessions | read-write | current | Configures the maximum number of allowable HTTP sessions. The default value is 16. |
| 1.3.6.1.4.1.4526.11.1.2.18.4 | ScalaragentHTTPHardTimeout | read-write | current | Configures the hard timeout for HTTP sessions in hours. The default value is 24 hours. A value of 0 gives an infinite timeout. |
| 1.3.6.1.4.1.4526.11.1.2.18.5 | ScalaragentHTTPSoftTimeout | read-write | current | Configures the soft (activity) timeout for HTTP sessions in minutes. The default value is 5 minutes. A value of 0 gives an infinite timeout. |
| 1.3.6.1.4.1.4526.11.1.3 | NodeagentSystemGroup | |||
| 1.3.6.1.4.1.4526.11.1.3.1 | ScalaragentSaveConfig | read-write | current | enable(1) will initiate an configuration save to nvram. Status is returned by the object agentSaveConfigStatus. |
| 1.3.6.1.4.1.4526.11.1.3.2 | ScalaragentClearConfig | read-write | current | clear config to factory defaults |
| 1.3.6.1.4.1.4526.11.1.3.3 | ScalaragentClearLags | read-write | current | clear lag configuration |
| 1.3.6.1.4.1.4526.11.1.3.4 | ScalaragentClearLoginSessions | read-write | current | close all telnet sessions |
| 1.3.6.1.4.1.4526.11.1.3.5 | ScalaragentClearPasswords | read-write | current | reset passwords |
| 1.3.6.1.4.1.4526.11.1.3.6 | ScalaragentClearPortStats | read-write | current | clear all port statistics |
| 1.3.6.1.4.1.4526.11.1.3.7 | ScalaragentClearSwitchStats | read-write | current | clear all switch statistics |
| 1.3.6.1.4.1.4526.11.1.3.8 | ScalaragentClearTrapLog | read-write | current | clear trap log |
| 1.3.6.1.4.1.4526.11.1.3.9 | ScalaragentClearVlan | read-write | current | clear vlan entries |
| 1.3.6.1.4.1.4526.11.1.3.10 | ScalaragentResetSystem | read-write | current | Resets the switch. This object is not valid for stacking platforms. |
| 1.3.6.1.4.1.4526.11.1.3.11 | ScalaragentSaveConfigStatus | read-only | current | Indicates the current status of an save configuration request. |
| 1.3.6.1.4.1.4526.11.1.4 | NodeagentCableTesterGroup | |||
| 1.3.6.1.4.1.4526.11.1.4.1 | ScalaragentCableTesterStatus | read-write | current | Status of the Virtual Cable Tester active(1) - cable testing is in progress. Set to this value to start the test. success(2) - A successful test was performed.… |
| 1.3.6.1.4.1.4526.11.1.4.2 | ScalaragentCableTesterIfIndex | read-write | current | Determines on which port to perform the cable test. Limited to copper based ports. |
| 1.3.6.1.4.1.4526.11.1.4.3 | ScalaragentCableTesterCableStatus | read-only | current | Indicates the results of the Cable Test. normal(1) - The cable is working correctly. open(2) - The cable is disconnected or there is a faulty connector. short(… |
| 1.3.6.1.4.1.4526.11.1.4.4 | ScalaragentCableTesterMinimumCableLength | read-only | current | The estimated length of the cable in meters. This value indicates the shortest length estimated. This object will return 0 if agentCableTesterStatus is not suc… |
| 1.3.6.1.4.1.4526.11.1.4.5 | ScalaragentCableTesterMaximumCableLength | read-only | current | The estimated length of the cable in meters. This value indicates the longest length estimated. This object will return 0 if agentCableTesterStatus is not succ… |
| 1.3.6.1.4.1.4526.11.1.4.6 | ScalaragentCableTesterCableFailureLocation | read-only | current | The estimated distance in meters from the end of the cable to the failure location. This object will return 0 if agentCableTesterStatus is not success(2). |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| AgentPortMask | OCTET STRING | current | Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents… |
| Ipv6Address | OCTET STRING (SIZE (16)) | current | This data type is used to model IPv6 addresses. This is a binary string of 16 octets in network byte-order. |
| Ipv6AddressIfIdentifier | OCTET STRING (SIZE (0..8)) | current | This data type is used to model IPv6 address interface identifiers. This is a binary string of up to 8 octets in network byte-order. |
| Ipv6AddressPrefix | OCTET STRING (SIZE (0..16)) | current | This data type is used to model IPv6 address prefixes. This is a binary string of up to 16 octets in network byte-order. |
| Ipv6IfIndex | Integer32 (1..2147483647) | current | A unique value, greater than zero for each internetwork-layer interface in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each internetwork-layer interface mus… |
| Ipv6IfIndexOrZero | Integer32 (0..2147483647) | current | This textual convention is an extension of the Ipv6IfIndex convention. The latter defines a greater than zero value used to identify an IPv6 interface in the managed system. This extension permits the additional value o… |
| PortList | OCTET STRING | current | Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents… |
| VlanList | OCTET STRING | current | Each octet within this value specifies a set of eight vlans, with the first octet specifying vlans 1 through 8, the second octet specifying vlans 9 through 16, etc. Within each octet, the most significant bit represents… |