NEWTEC-DVBMODULATOR-MIB
162 objects
Newtec modular DVB modulator MIB containing definitions for DVB-S and DVB-S2 modulator functionality.
Imported Objects
| FLOAT-TC-MIB MISSING | Float32TC |
| NEWTEC-MAIN-MIB | ntcFunction |
| NEWTEC-TC-MIB | NtcAlarmState NtcEnable |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Integer32 MODULE-IDENTITY OBJECT-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.5835.5.2.1000 | IdentityntcDvbModulator | Newtec modular DVB modulator MIB containing definitions for DVB-S and DVB-S2 modulator functionality. | ||
| 1.3.6.1.4.1.5835.5.2.1000.1 | IdentityntcDvbModObjects | current | Container holding ntcDvbModObjects definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.1 | ScalarntcDvbModMode | read-write | current | The modulation standard defines the operating mode of the modulator. - DVB-S2 : compatible with EN302307. Single Stream Transport Stream Broadcasting Applicati… |
| 1.3.6.1.4.1.5835.5.2.1000.1.2 | ScalarntcDvbModTransmit | read-write | current | Enable or disable the modulator output transmit signal. When it is enabled the actual output can still be switched-off upon detection of e.g. general device al… |
| 1.3.6.1.4.1.5835.5.2.1000.1.3 | ScalarntcDvbModTransmitState | read-only | current | Current transmit status of the modulator (on or off). The actual transmit status is determined by the transmit configuration parameter and by other events. Not… |
| 1.3.6.1.4.1.5835.5.2.1000.1.4 | ScalarntcDvbModTxCtrlGenDeviceAlarm | read-write | current | Configure the impact of a General Device alarm on the Modulator Transmit. |
| 1.3.6.1.4.1.5835.5.2.1000.1.5 | ScalarntcDvbModTxCtrlGenInterfaceAlarm | read-write | current | Configure the impact of a General Interface Alarm on the Modulator Transmit |
| 1.3.6.1.4.1.5835.5.2.1000.1.6 | ScalarntcDvbModOutputFrequency | read-write | current | Modulator output frequency setting. Current devices support a frequency range of 50..180 Mhz or 960..2150 MHz. |
| 1.3.6.1.4.1.5835.5.2.1000.1.7 | ScalarntcDvbModRollOff | read-write | current | The transmit filter Roll-off factor setting determines the output spectrum excess bandwidth by controlling the RCRO (Root Cosine Roll-off) factor of the matche… |
| 1.3.6.1.4.1.5835.5.2.1000.1.8 | ScalarntcDvbModOccupiedBandWidth | read-only | current | The '-26 dB' bandwidth of the signal. This is calculated as the symbol rate multiplied with (1 + a) with a = the selected roll-off factor. |
| 1.3.6.1.4.1.5835.5.2.1000.1.9 | ScalarntcDvbModOutputBand | read-only | current | Indicates the used output frequency band: IF band or L band. |
| 1.3.6.1.4.1.5835.5.2.1000.1.10 | ScalarntcDvbModSpectrumPolarity | read-write | current | Transmit spectrum polarity selection. The spectrum at IFL and at RF is coupled by the installed upconverter module. This can be deduced from the frequency conv… |
| 1.3.6.1.4.1.5835.5.2.1000.1.11 | ScalarntcDvbModOutputLevel | read-write | current | Modulator output level setting in dBm. Adjustable in steps of 0.1 dBm. Float represented as integer is scaled by a factor of 10. i.e. a value of '-103' means '… |
| 1.3.6.1.4.1.5835.5.2.1000.1.12 | ScalarntcDvbModClockOutput | read-write | current | Enables or disables the transmission of a 10MHz clock signal on the RF output cable. |
| 1.3.6.1.4.1.5835.5.2.1000.1.13 | ScalarntcDvbModCarrierModulation | read-write | current | Carrier modulation selection : - modulation on: Operational modulated carrier signal - pure carrier: unmodulated output signal - 'test modulation CLK/n': Carri… |
| 1.3.6.1.4.1.5835.5.2.1000.1.14 | ScalarntcDvbModAmplSlopeEqualizer | read-write | current | Configuration of the amplitude slope equalizer. An amplitude slope in the up-converter or in the high power amplifier can be compensated by using this equalize… |
| 1.3.6.1.4.1.5835.5.2.1000.1.15 | IdentityntcDvbModDvbs2Acm | current | Container holding ntcDvbModDvbs2Acm definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.15.1 | ScalarntcDvbModDvbs2AcmSymbolRate | read-write | deprecated | Define the required symbol rate in baud. |
| 1.3.6.1.4.1.5835.5.2.1000.1.16 | IdentityntcDvbModDvbs2 | current | Container holding ntcDvbModDvbs2 definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.16.1 | ScalarntcDvbModDvbs2Isi | read-write | deprecated | The DVB-S2 Input Stream Identifier (ISI) is present in the second byte position of the MATYPE field in the baseband header of a DVB-S2 baseband frame. It is a … |
| 1.3.6.1.4.1.5835.5.2.1000.1.16.2 | ScalarntcDvbModDvbs2FrameType | read-write | current | Dvb-S2 defines 2 FEC-frame types : - normal: FECframes of 64800 bits or 8100 bytes - short: FECframes of 16200 bits or 2025 bytes Short frames are used when wo… |
| 1.3.6.1.4.1.5835.5.2.1000.1.16.3 | ScalarntcDvbModDvbs2ModCod | read-write | current | The selection of modulation type and the FEC rate. |
| 1.3.6.1.4.1.5835.5.2.1000.1.16.4 | ScalarntcDvbModDvbs2Pilots | read-write | current | Dvb-S2 Physical Layer Pilot insertion. When enabled, every 16 slots (of 90 symbols) the modulator will insert 36 unmodulated symbols to aid in receiver synchro… |
| 1.3.6.1.4.1.5835.5.2.1000.1.16.5 | ScalarntcDvbModDvbs2RatePriority | read-write | deprecated | Select the rate mode (symbol rate or bit rate). The selected rate will be kept constant when other parameters have impact a the modulator rate. Only the select… |
| 1.3.6.1.4.1.5835.5.2.1000.1.16.6 | ScalarntcDvbModDvbs2SymbolRate | read-write | deprecated | Define the required symbol rate in baud. |
| 1.3.6.1.4.1.5835.5.2.1000.1.16.7 | ScalarntcDvbModDvbs2BitRate | read-write | deprecated | Define the required bit rate of the modulator. Current devices support a range of 50000 to 250000000 bps. |
| 1.3.6.1.4.1.5835.5.2.1000.1.16.8 | ScalarntcDvbModDvbs2MeasuredPktCount | read-only | deprecated | Measured TS packet count of the modulator. |
| 1.3.6.1.4.1.5835.5.2.1000.1.16.9 | ScalarntcDvbModDvbs2MeasuredBitRate | read-only | deprecated | Measured bitrate of the modulator. |
| 1.3.6.1.4.1.5835.5.2.1000.1.16.10 | ScalarntcDvbModDvbs2PhyLayerEfficiency | read-only | current | The measured physical layer efficiency, equal to the percentage of non-dummy physical layer frames. Float represented as integer is scaled by a factor of 100. … |
| 1.3.6.1.4.1.5835.5.2.1000.1.16.11 | ScalarntcDvbModDvbs2BbLayerEfficiency | read-only | current | The measured baseband layer efficiency, equal to the percentage user data in tbe baseband frames. Float represented as integer is scaled by a factor of 100. i.… |
| 1.3.6.1.4.1.5835.5.2.1000.1.16.12 | ScalarntcDvbModDvbs2DumPlScramblMode | read-write | current | The dummy physical layer scrambler mode can be set to continuous, to achieve more randomness in the carrier data as required for bandwidth cancellation. |
| 1.3.6.1.4.1.5835.5.2.1000.1.16.13 | ScalarntcDvbModDvbs2PlScrambSig | read-write | current | The physical layer scrambler signature. |
| 1.3.6.1.4.1.5835.5.2.1000.1.16.14 | ScalarntcDvbModDvbs2Reset | read-write | deprecated | Reset the modulator monitoring counters. |
| 1.3.6.1.4.1.5835.5.2.1000.1.16.15 | ScalarntcDvbModDvbs2RollOffSignalling | read-write | current | When a Roll-off <20% is configured, this setting is used to put the Roll-off bits in the baseband header to reserved (11) or to a standardized value. Some rece… |
| 1.3.6.1.4.1.5835.5.2.1000.1.17 | IdentityntcDvbModDvbs | current | Container holding ntcDvbModDvbs definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.17.1 | ScalarntcDvbModDvbsModCod | read-write | current | The selection of the FEC code-rate and modulation scheme supported by DVB-S |
| 1.3.6.1.4.1.5835.5.2.1000.1.17.2 | ScalarntcDvbModDvbsRatePriority | read-write | deprecated | Select the rate mode (symbol rate or bit rate). The selected rate will be kept constant when other parameters have impact a the modulator rate. Only the select… |
| 1.3.6.1.4.1.5835.5.2.1000.1.17.3 | ScalarntcDvbModDvbsSymbolRate | read-write | deprecated | Define the required symbol rate in baud. |
| 1.3.6.1.4.1.5835.5.2.1000.1.17.4 | ScalarntcDvbModDvbsBitRate | read-write | deprecated | Define the required bit rate of the modulator. Current devices support a range of 50000 to 250000000 bps. |
| 1.3.6.1.4.1.5835.5.2.1000.1.17.5 | ScalarntcDvbModDvbsMeasuredPktCount | read-only | deprecated | Measured TS packet count of the modulator. |
| 1.3.6.1.4.1.5835.5.2.1000.1.17.6 | ScalarntcDvbModDvbsMeasuredBitRate | read-only | deprecated | Measured bitrate of the modulator. |
| 1.3.6.1.4.1.5835.5.2.1000.1.17.7 | ScalarntcDvbModDvbsReset | read-write | deprecated | Reset the modulator monitoring counters. |
| 1.3.6.1.4.1.5835.5.2.1000.1.18 | IdentityntcDvbModEqualink | current | Container holding ntcDvbModEqualink definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.18.1 | IdentityntcDvbModEqlnkLinear | current | Container holding ntcDvbModEqlnkLinear definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.18.1.1 | ScalarntcDvbModEqlnkLinMode | read-write | current | Enable or disable linear equalink. Enable this component to compensate amplitude distorions and group delay distortions. This improves the transponder throughp… |
| 1.3.6.1.4.1.5835.5.2.1000.1.18.1.2 | ScalarntcDvbModEqlnkLinState | read-only | current | Displays the current linear predistortion status. The actual linear predistortion status is determined by the configuration parameter but is also automatically… |
| 1.3.6.1.4.1.5835.5.2.1000.1.18.1.3 | ScalarntcDvbModEqlnkLinInfo | read-only | current | Detailed info for linear equalink. |
| 1.3.6.1.4.1.5835.5.2.1000.1.18.1.4 | IdentityntcDvbModEqlnkLinConf | current | Container holding ntcDvbModEqlnkLinConf definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.18.1.4.1 | IdentityntcDvbModEqlnkLinApp | current | Container holding ntcDvbModEqlnkLinApp definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.18.1.4.1.1 | ScalarntcDvbModEqlnkLinAppOutFreq | read-write | current | Modulator output frequency that was used during the calibration. |
| 1.3.6.1.4.1.5835.5.2.1000.1.18.1.4.1.2 | ScalarntcDvbModEqlnkLinAppRollOff | read-write | current | The transmit filter roll-off factor setting determines the output spectrum excess bandwidth by controlling the RCRO (Root Cosine Roll-Off) factor of the matche… |
| 1.3.6.1.4.1.5835.5.2.1000.1.18.1.4.1.3 | ScalarntcDvbModEqlnkLinAppSymRate | read-write | current | The Symbol Rate that was used during the calibration. |
| 1.3.6.1.4.1.5835.5.2.1000.1.18.2 | IdentityntcDvbModEqlnkNonlinear | current | Container holding ntcDvbModEqlnkNonlinear definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.18.2.1 | ScalarntcDvbModEqlnkNonlinMode | read-write | current | Enable or disable non-linear equalink. Non-linear distortion is typically caused by non-linearity in the amplifier of the satellite. Enable this parameter to c… |
| 1.3.6.1.4.1.5835.5.2.1000.1.18.2.2 | ScalarntcDvbModEqlnkNonlinState | read-only | current | Displays the current non-linear predistortion status. The actual non-linear predistortion status is determined by the configuration parameter but is also autom… |
| 1.3.6.1.4.1.5835.5.2.1000.1.18.2.3 | ScalarntcDvbModEqlnkNonlinInfo | read-only | current | Detailed info for non-linear equalink |
| 1.3.6.1.4.1.5835.5.2.1000.1.18.2.4 | IdentityntcDvbModEqlnkNonlinConf | current | Container holding ntcDvbModEqlnkNonlinConf definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.18.2.4.1 | IdentityntcDvbModEqlnkNonlinApp | current | Container holding ntcDvbModEqlnkNonlinApp definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.18.2.4.1.1 | ScalarntcDvbModEqlnkNonlinAppOutFreq | read-write | current | Modulator output frequency that was used during the calibration. |
| 1.3.6.1.4.1.5835.5.2.1000.1.18.2.4.1.2 | ScalarntcDvbModEqlnkNonlinAppVersion | read-write | current | Equalink version that was used during calibration |
| 1.3.6.1.4.1.5835.5.2.1000.1.19 | IdentityntcDvbModAlarm | current | Container holding ntcDvbModAlarm definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.19.1 | ScalarntcDvbModAlmGeneralModulator | read-only | current | This alarm is raised when there is a general modulator alarm. This variable indicates the current status of the alarm. |
| 1.3.6.1.4.1.5835.5.2.1000.1.19.2 | ScalarntcDvbModAlmNoInputSignal | read-only | current | This alarm is raised when no input signal is detected at the input of the modulator. This variable indicates the current status of the alarm. |
| 1.3.6.1.4.1.5835.5.2.1000.1.19.3 | ScalarntcDvbModAlmBufferUnderflow | read-only | current | This alarm is raised when the input data buffer to the modulator is empty. This variable indicates the current status of the alarm. |
| 1.3.6.1.4.1.5835.5.2.1000.1.19.4 | ScalarntcDvbModAlmBufferOverflow | read-only | current | This alarm is raised when the input data buffer of the modulator is full. This variable indicates the current status of the alarm. |
| 1.3.6.1.4.1.5835.5.2.1000.1.19.5 | ScalarntcDvbModAlmNoInputFrameSync | read-only | current | This alarm indicates loss of input framing on the incoming data of the modulator. This variable indicates the current status of the alarm. |
| 1.3.6.1.4.1.5835.5.2.1000.1.19.6 | ScalarntcDvbModAlmNoBaseBandFrameSync | read-only | current | This alarm indicates synchronization loss of the baseband framer on the incoming data. This variable indicates the current status of the alarm. |
| 1.3.6.1.4.1.5835.5.2.1000.1.19.7 | ScalarntcDvbModAlmNoPhyLayerFrameSync | read-only | current | This alarm indicates loss of synchronization between the physical layer framing and the baseband frames. This variable indicates the current status of the alar… |
| 1.3.6.1.4.1.5835.5.2.1000.1.19.8 | ScalarntcDvbModAlmSynthFail | read-only | current | This alarm is raised when there is a failure with a synthesizer. It indicates a malfunction of the synthesizer hardware which generates the IFL carrier frequen… |
| 1.3.6.1.4.1.5835.5.2.1000.1.19.9 | ScalarntcDvbModAlmRefSynthOutOfLock | read-only | current | This alarm is raised when the reference synthesizer is out of lock. It indicates a malfunction of the reference synthesizer hardware which generates the IFL ca… |
| 1.3.6.1.4.1.5835.5.2.1000.1.19.10 | ScalarntcDvbModAlmLo1SynthOutOfLock | read-only | current | This alarm is raised when the synthesizer of the first Local Oscillator is out of lock. It indicates a malfunction of the synthesizer hardware which generates … |
| 1.3.6.1.4.1.5835.5.2.1000.1.19.11 | ScalarntcDvbModAlmLo2SynthOutOfLock | read-only | current | This alarm is raised when the synthesizer of the second Local Oscillator is out of lock. It indicates a malfunction of the synthesizer hardware which generates… |
| 1.3.6.1.4.1.5835.5.2.1000.1.19.12 | ScalarntcDvbModAlmNoCalibrationData | read-only | current | This alarm is raised when there is no Calibration data available for the modulator. This variable indicates the current status of the alarm. |
| 1.3.6.1.4.1.5835.5.2.1000.1.19.13 | ScalarntcDvbModAlmDacFailure | read-only | current | This alarm is raised when there is a general DAC Failure. This variable indicates the current status of the alarm. |
| 1.3.6.1.4.1.5835.5.2.1000.1.19.14 | ScalarntcDvbModAlmBucPowerMinCurrent | read-only | current | This alarm is raised when measured current for block up converter power is below specified minimal value. This variable indicates the current status of the ala… |
| 1.3.6.1.4.1.5835.5.2.1000.1.19.15 | ScalarntcDvbModAlmBucPowerOverload | read-only | current | This alarm is raised when overload is detected. This variable indicates the current status of the alarm. |
| 1.3.6.1.4.1.5835.5.2.1000.1.19.16 | ScalarntcDvbModAlmBucPowerSupply | read-only | current | This alarm is raised when 24V/48V supply is not operational This variable indicates the current status of the alarm. |
| 1.3.6.1.4.1.5835.5.2.1000.1.19.17 | ScalarntcDvbModAlmBucPowerCap | read-only | current | This alarm is raised when there is too much output capacitance connected. This variable indicates the current status of the alarm. |
| 1.3.6.1.4.1.5835.5.2.1000.1.19.18 | ScalarntcDvbModAlmBucPowerShortCircuit | read-only | current | This alarm is raised when short circuit is detected. This variable indicates the current status of the alarm. |
| 1.3.6.1.4.1.5835.5.2.1000.1.19.19 | ScalarntcDvbModAlmBucPowerHardware | read-only | current | This alarm is raised when communication with block up converter power unit is lost. This variable indicates the current status of the alarm. |
| 1.3.6.1.4.1.5835.5.2.1000.1.20 | ScalarntcDvbModInputType | read-write | current | The type of input packets or frames for the modulator. |
| 1.3.6.1.4.1.5835.5.2.1000.1.21 | IdentityntcDvbModRfCid | current | Container holding ntcDvbModRfCid definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.21.1 | ScalarntcDvbModRfCidEnable | read-write | current | Enable or disable the RF Carrier ID insertion. |
| 1.3.6.1.4.1.5835.5.2.1000.1.21.2 | ScalarntcDvbModRfCidId | read-only | current | The 64-bit DVB CID Global Unique Identifier is based on the IEEE EUI-64 derived from a 48 bit MAC address of the management interface. |
| 1.3.6.1.4.1.5835.5.2.1000.1.21.3 | ScalarntcDvbModRfCidFormat | read-only | current | Revision code anticipating possible changes in the number and possible content of the fields. |
| 1.3.6.1.4.1.5835.5.2.1000.1.21.4 | ScalarntcDvbModRfCidSendGeoCord | read-write | current | Enable or disable sending geo coordinates (longitude/latitude) in a DVB-CID message. |
| 1.3.6.1.4.1.5835.5.2.1000.1.21.5 | ScalarntcDvbModRfCidLatitude | read-write | current | Geo coordinates of modulator in degrees (latitude from +00.0000 to +/-90.0000) |
| 1.3.6.1.4.1.5835.5.2.1000.1.21.6 | ScalarntcDvbModRfCidLongitude | read-write | current | Geo coordinates of modulator in degrees (longitude from +000.0000 to +/-180.0000) |
| 1.3.6.1.4.1.5835.5.2.1000.1.21.7 | ScalarntcDvbModRfCidPhone | read-write | current | Operators telephone number (for example +323 780 65 00 ext. 0) Regular expression : (?-mix:(\+?[ \d]+(ext\.)?[ \d]*)?) |
| 1.3.6.1.4.1.5835.5.2.1000.1.21.8 | ScalarntcDvbModRfCidData | read-write | current | Custom user data (up to 24 ASCII chars) |
| 1.3.6.1.4.1.5835.5.2.1000.1.21.9 | ScalarntcDvbModRfCidLatitudeString | read-write | current | Geo coordinates of modulator in degrees (latitude from +00.0000 to +/-90.0000) |
| 1.3.6.1.4.1.5835.5.2.1000.1.21.10 | ScalarntcDvbModRfCidLongitudeString | read-write | current | Geo coordinates of modulator in degrees (longitude from +000.0000 to +/-180.0000) |
| 1.3.6.1.4.1.5835.5.2.1000.1.22 | IdentityntcDvbModDcBuc | current | Container holding ntcDvbModDcBuc definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.22.1 | ScalarntcDvbModDcBucEnable | read-write | current | Enable or disable block up converter power. |
| 1.3.6.1.4.1.5835.5.2.1000.1.22.2 | ScalarntcDvbModDcBucVoltage | read-write | current | Select block up converter power voltage. |
| 1.3.6.1.4.1.5835.5.2.1000.1.22.3 | ScalarntcDvbModDcBucOutVoltage | read-only | current | Block up converter power measured output voltage. |
| 1.3.6.1.4.1.5835.5.2.1000.1.22.4 | ScalarntcDvbModDcBucOutCurrent | read-only | current | Block up converter power measured output current. |
| 1.3.6.1.4.1.5835.5.2.1000.1.22.5 | ScalarntcDvbModDcBucMinCurrent | read-write | current | Minimal value for operational block up converter power current. If measured value drops below this value alarm will be raised. |
| 1.3.6.1.4.1.5835.5.2.1000.1.23 | ScalarntcDvbModRatePriority | read-write | current | Select the rate mode (symbol rate or bit rate). The selected rate will be kept constant when other parameters have impact a the modulator rate. Only the select… |
| 1.3.6.1.4.1.5835.5.2.1000.1.24 | ScalarntcDvbModSymbolRate | read-write | current | Define the required symbol rate in baud. |
| 1.3.6.1.4.1.5835.5.2.1000.1.25 | ScalarntcDvbModBitRate | read-write | current | Define the required bit rate of the modulator. Current devices support a range of 50000 to 250000000 bps. |
| 1.3.6.1.4.1.5835.5.2.1000.1.26 | ScalarntcDvbModMeasuredPktCount | read-only | current | Measured TS packet count of the modulator. |
| 1.3.6.1.4.1.5835.5.2.1000.1.27 | ScalarntcDvbModMeasuredBitRate | read-only | current | Measured bitrate of the modulator. |
| 1.3.6.1.4.1.5835.5.2.1000.1.28 | ScalarntcDvbModReset | read-write | current | Reset the modulator monitoring counters. |
| 1.3.6.1.4.1.5835.5.2.1000.1.29 | IdentityntcDvbModS2Ext | current | Container holding ntcDvbModS2Ext definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.29.1 | ScalarntcDvbModS2ExtModCod | read-write | current | The list of S2 Extensions MODCODs is an extension to the standard DVB-S2 MODCODs. The new MODCODs offer improved efficiency if transmission conditions allow it. |
| 1.3.6.1.4.1.5835.5.2.1000.1.29.2 | ScalarntcDvbModS2ExtPhyLayerEfficiency | read-only | current | The measured physical layer efficiency, equal to the percentage of non-dummy physical layer frames. Float represented as integer is scaled by a factor of 100. … |
| 1.3.6.1.4.1.5835.5.2.1000.1.29.3 | ScalarntcDvbModS2ExtBbLayerEfficiency | read-only | current | The measured baseband layer efficiency, equal to the percentage user data in tbe baseband frames. Float represented as integer is scaled by a factor of 100. i.… |
| 1.3.6.1.4.1.5835.5.2.1000.1.29.4 | ScalarntcDvbModS2ExtDumPlScramblMode | read-write | current | The dummy physical layer scrambler mode can be set to continuous, to achieve more randomness in the carrier data as required for bandwidth cancellation. |
| 1.3.6.1.4.1.5835.5.2.1000.1.29.5 | ScalarntcDvbModS2ExtPlScrambSig | read-write | current | The physical layer scrambler signature. |
| 1.3.6.1.4.1.5835.5.2.1000.1.29.6 | ScalarntcDvbModS2ExtRollOffSignalling | read-write | current | When a Roll-off <20% is configured, this setting is used to put the Roll-off bits in the baseband header to reserved (11) or to a standardized value. Some rece… |
| 1.3.6.1.4.1.5835.5.2.1000.1.30 | IdentityntcDvbModTurbo | current | Container holding ntcDvbModTurbo definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.30.1 | ScalarntcDvbModTurboModCod | read-write | current | The selection of the FEC code-rate and modulation scheme supported by TURBO |
| 1.3.6.1.4.1.5835.5.2.1000.1.30.2 | ScalarntcDvbModTurboDeleteSync | read-write | current | Enable or disable deletion of the sync byte |
| 1.3.6.1.4.1.5835.5.2.1000.1.31 | IdentityntcDvbModAmcDvbs | current | Container holding ntcDvbModAmcDvbs definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.31.1 | ScalarntcDvbModAmcDvbsModCod | read-write | current | The selection of the FEC code-rate and modulation scheme supported by AMC-S |
| 1.3.6.1.4.1.5835.5.2.1000.1.32 | IdentityntcDvbModAmcNbc | current | Container holding ntcDvbModAmcNbc definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.32.1 | ScalarntcDvbModAmcNbcFrameType | read-write | current | Dvb-S2 defines 2 FEC-frame types : - normal: FECframes of 64800 bits or 8100 bytes - short: FECframes of 16200 bits or 2025 bytes Short frames are used when wo… |
| 1.3.6.1.4.1.5835.5.2.1000.1.32.2 | ScalarntcDvbModAmcNbcModCod | read-write | current | The selection of modulation type and the FEC rate. |
| 1.3.6.1.4.1.5835.5.2.1000.1.32.3 | ScalarntcDvbModAmcNbcPilots | read-write | current | Dvb-S2 Physical Layer Pilot insertion. When enabled, every 16 slots (of 90 symbols) the modulator will insert 36 unmodulated symbols to aid in receiver synchro… |
| 1.3.6.1.4.1.5835.5.2.1000.1.32.4 | ScalarntcDvbModAmcNbcPLEfficiency | read-only | current | The measured physical layer efficiency, equal to the percentage of non-dummy physical layer frames. Float represented as integer is scaled by a factor of 100. … |
| 1.3.6.1.4.1.5835.5.2.1000.1.32.5 | ScalarntcDvbModAmcNbcBbLayerEfficiency | read-only | current | The measured baseband layer efficiency, equal to the percentage user data in tbe baseband frames. Float represented as integer is scaled by a factor of 100. i.… |
| 1.3.6.1.4.1.5835.5.2.1000.1.32.6 | ScalarntcDvbModAmcNbcPlHdrScrmSeq | read-write | current | Physical layer scrambling sequence key |
| 1.3.6.1.4.1.5835.5.2.1000.1.32.7 | ScalarntcDvbModAmcNbcRollOffSignalling | read-write | current | When a Roll-off <20% is configured, this setting is used to put the Roll-off bits in the baseband header to reserved (11) or to a standardized value. Some rece… |
| 1.3.6.1.4.1.5835.5.2.1000.1.33 | ScalarntcDvbModActualOutputLevel | read-only | current | Modulator output level setting in dBm. Adjustable in steps of 0.1 dBm. Float represented as integer is scaled by a factor of 10. i.e. a value of '-103' means '… |
| 1.3.6.1.4.1.5835.5.2.1000.1.34 | ScalarntcDvbModTransmitStateReason | read-only | current | Reason for current Transmit State |
| 1.3.6.1.4.1.5835.5.2.1000.1.35 | IdentityntcDvbModLinkOpt | current | Container holding ntcDvbModLinkOpt definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.35.1 | ScalarntcDvbModLinkOptTransMode | read-write | current | Transponder Operation Mode selection. |
| 1.3.6.1.4.1.5835.5.2.1000.1.35.2 | ScalarntcDvbModMaxModulation | read-write | current | The maximum modulation order to which the outbound carrier is optimized. |
| 1.3.6.1.4.1.5835.5.2.1000.1.36 | ScalarntcDvbModAllowChangesWhileTxOn | read-write | current | This field allows you to choose if the main modulation parameters can be altered while the transmit is on. |
| 1.3.6.1.4.1.5835.5.2.1000.1.37 | ScalarntcDvbModStandbyRedundancyState | read-write | current | Default connector redundancy state when the Device Redundancy is in standby mode. |
| 1.3.6.1.4.1.5835.5.2.1000.1.38 | IdentityntcDvbModDSNGProfiles | current | Container holding ntcDvbModDSNGProfiles definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.38.38 | ScalarntcDvbModDSNGProfilesProfile | read-write | current | DSNG profile is named after its occupied bandwidth |
| 1.3.6.1.4.1.5835.5.2.1000.1.38.39 | ScalarntcDvbModDSNGProfilesLevel | read-write | current | DSNG profile level that defines the proposed application |
| 1.3.6.1.4.1.5835.5.2.1000.1.39 | ScalarntcDvbModStreamMode | read-write | current | Specify if more than one input stream is multiplexed into the modulator or not. This sometimes impacts receiver compatibility. |
| 1.3.6.1.4.1.5835.5.2.1000.1.40 | IdentityntcDvbModAmcDl | current | Container holding ntcDvbModAmcDl definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.40.1 | ScalarntcDvbModAmcDlModCod | read-write | current | The selection of the FEC code-rate and modulation scheme supported by AMC-DL |
| 1.3.6.1.4.1.5835.5.2.1000.1.41 | ScalarntcDvbModIfOutputLevel | read-write | current | Modulator output level setting in dBm. Adjustable in steps of 0.1 dBm. Float represented as integer is scaled by a factor of 10. i.e. a value of '-103' means '… |
| 1.3.6.1.4.1.5835.5.2.1000.1.42 | ScalarntcDvbModLbandOutputLevel | read-write | current | Modulator output level setting in dBm. Adjustable in steps of 0.1 dBm. Float represented as integer is scaled by a factor of 10. i.e. a value of '-103' means '… |
| 1.3.6.1.4.1.5835.5.2.1000.1.43 | ScalarntcDvbModIfOutputFrequency | read-write | current | When the IF to L-Band converter is inside the device, then both IF and L-Band is available at the same time at the output of the device. This means that 2 inde… |
| 1.3.6.1.4.1.5835.5.2.1000.1.44 | ScalarntcDvbModLbandOutputFrequency | read-write | current | When the IF to L-Band converter is inside the device, then both IF and L-Band is available at the same time at the output of the device. This means that 2 inde… |
| 1.3.6.1.4.1.5835.5.2.1000.1.45 | ScalarntcDvbModLbandTx | read-write | current | Enable or disable the modulator L-Band output transmit signal. When it is enabled the actual output can still be switched-off upon detection of e.g. general de… |
| 1.3.6.1.4.1.5835.5.2.1000.1.46 | ScalarntcDvbModLbandTxState | read-only | current | Current L-Band transmit status of the modulator (on or off). The actual transmit status is determined by the transmit configuration parameter and by other even… |
| 1.3.6.1.4.1.5835.5.2.1000.1.47 | ScalarntcDvbModLbandTxStateReason | read-only | current | Reason for current L-Band Transmit State |
| 1.3.6.1.4.1.5835.5.2.1000.1.48 | IdentityntcDvbModExtConv | current | Container holding ntcDvbModExtConv definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.48.1 | ScalarntcDvbModExtConvEnable | read-write | current | Enable or disable the external convertor frequency specification |
| 1.3.6.1.4.1.5835.5.2.1000.1.48.2 | ScalarntcDvbModExtConvRfFrequency | read-write | current | RF frequency |
| 1.3.6.1.4.1.5835.5.2.1000.1.48.3 | ScalarntcDvbModExtConvLoFrequency | read-write | current | LO frequency |
| 1.3.6.1.4.1.5835.5.2.1000.1.48.4 | ScalarntcDvbModExtConvSpectrumInv | read-write | current | Specifies in the external LO converter inverts the spectrum or not. |
| 1.3.6.1.4.1.5835.5.2.1000.1.49 | IdentityntcDvbModConv | current | Container holding ntcDvbModConv definitions. | |
| 1.3.6.1.4.1.5835.5.2.1000.1.49.1 | ScalarntcDvbModConvRfFrequency | read-write | current | RF frequency |
| 1.3.6.1.4.1.5835.5.2.1000.1.49.2 | ScalarntcDvbModConvExtLbandTx | read-write | current | Enables or disables block upconverter output of the external L-band input signal. |
| 1.3.6.1.4.1.5835.5.2.1000.1.49.3 | ScalarntcDvbModConvLoFrequency | read-only | current | Converter module LO frequency |
| 1.3.6.1.4.1.5835.5.2.1000.1.49.4 | ScalarntcDvbModConvRfGain | read-only | current | Gain of the installed converter module. |
| 1.3.6.1.4.1.5835.5.2.1000.1.49.5 | ScalarntcDvbModConvOutputLevel | read-write | current | Converter output level setting in dBm. Adjustable in steps of 0.1 dBm. Float represented as integer is scaled by a factor of 10. i.e. a value of '-103' means '… |
| 1.3.6.1.4.1.5835.5.2.1000.1.50 | ScalarntcDvbModExtCableLoss | read-write | current | Modulator external cable loss in dBm. Adjustable in steps of 0.1 dBm. Float represented as integer is scaled by a factor of 10. i.e. a value of '-103' means '-… |
| 1.3.6.1.4.1.5835.5.2.1000.2 | IdentityntcDvbModConformance | current | Conformance requirements. | |
| 1.3.6.1.4.1.5835.5.2.1000.2.1 | IdentityntcDvbModConfCompliance | current | Device compliance statements. | |
| 1.3.6.1.4.1.5835.5.2.1000.2.1.1 | CompliancentcDvbModConfCompV1Standard | current | Compliance statement for Newtec device MIB implementations. | |
| 1.3.6.1.4.1.5835.5.2.1000.2.2 | IdentityntcDvbModConfGroup | current | Groups used by device compliance statements. | |
| 1.3.6.1.4.1.5835.5.2.1000.2.2.1 | GroupntcDvbModConfGrpV1Standard | current | Managed objects that constitute version 1 of a system device with standard capabilities. | |
| 1.3.6.1.4.1.5835.5.2.1000.2.2.2 | GroupntcDvbModConfGrpObsolete | obsolete | Managed objects which are deprecated or obsolete |