NEWTEC-TSANALYSER-MIB
46 objects
Newtec modular MIB containing definitions for transport stream analyser functionality.
Imported Objects
| NEWTEC-MAIN-MIB | ntcFunction |
| NEWTEC-TC-MIB | NtcAlarmState NtcEnable |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter64 Integer32 MODULE-IDENTITY OBJECT-IDENTITY OBJECT-TYPE Unsigned32 |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.5835.5.2.1400 | IdentityntcTsAnalyser | Newtec modular MIB containing definitions for transport stream analyser functionality. | ||
| 1.3.6.1.4.1.5835.5.2.1400.1 | IdentityntcTsAnlyObjects | current | Container holding ntcTsAnlyObjects definitions. | |
| 1.3.6.1.4.1.5835.5.2.1400.1.1 | ScalarntcTsAnlyEble | read-write | current | Enable or disable Transport Stream Analyzer. |
| 1.3.6.1.4.1.5835.5.2.1400.1.2 | ScalarntcTsAnlyReset | read-write | current | Reset Transport Stream Analyzer |
| 1.3.6.1.4.1.5835.5.2.1400.1.3 | ScalarntcTsAnlyEstimatedTsRate | read-only | current | Displays the measured TS bit rate in bps. Current devices support a range of 0 to 2500000000 bps. |
| 1.3.6.1.4.1.5835.5.2.1400.1.4 | TablentcTsAnlyPidTable | not-accessible | current | A table containing all detected PID's of the incoming traffic stream with corresponding measurements. |
| 1.3.6.1.4.1.5835.5.2.1400.1.4.1 | RowntcTsAnlyPidEntry | not-accessible | current | A conceptual row of the ntcTsAnlyPidTable. |
| 1.3.6.1.4.1.5835.5.2.1400.1.4.1.1 | ColumnntcTsAnlyPidPid | not-accessible | current | PID |
| 1.3.6.1.4.1.5835.5.2.1400.1.4.1.2 | ColumnntcTsAnlyPidType | read-only | current | PID Type |
| 1.3.6.1.4.1.5835.5.2.1400.1.4.1.3 | ColumnntcTsAnlyPidPIDRate | read-only | current | PID Rate for a specific stream. |
| 1.3.6.1.4.1.5835.5.2.1400.1.4.1.4 | ColumnntcTsAnlyPidContinuityError | read-only | current | Continuity Count Error |
| 1.3.6.1.4.1.5835.5.2.1400.1.4.1.5 | ColumnntcTsAnlyPidTransportError | read-only | current | Transport Error |
| 1.3.6.1.4.1.5835.5.2.1400.1.4.1.6 | ColumnntcTsAnlyPidCtuCntErrorCntr | read-only | current | Indicates the number of packets with a continuity count error. |
| 1.3.6.1.4.1.5835.5.2.1400.1.5 | TablentcTsAnlyPcrPidTable | not-accessible | current | A table of PCR PID's with detailled time measurements. |
| 1.3.6.1.4.1.5835.5.2.1400.1.5.1 | RowntcTsAnlyPcrPidEntry | not-accessible | current | A conceptual row of the ntcTsAnlyPcrPidTable. |
| 1.3.6.1.4.1.5835.5.2.1400.1.5.1.1 | ColumnntcTsAnlyPcrPidPid | not-accessible | current | PID |
| 1.3.6.1.4.1.5835.5.2.1400.1.5.1.2 | ColumnntcTsAnlyPcrPidPcrIntervalTime | read-only | current | Measured interval time (in milliseconds) between 2 PCR packets. |
| 1.3.6.1.4.1.5835.5.2.1400.1.5.1.3 | ColumnntcTsAnlyPcrPidPcrRepeatError | read-only | current | PCR Repetition Error is raised when the spacing between two consecutive PCR values is more than 40ms. The condition can occur when PCR packets get lost or when… |
| 1.3.6.1.4.1.5835.5.2.1400.1.5.1.4 | ColumnntcTsAnlyPcrPidPcrAccuracyError | read-only | current | The PCR Accuracy error is raised when the PCR accuracy exceeds +/- 500nsec. The definition of the alarm is taken from TR101290. |
| 1.3.6.1.4.1.5835.5.2.1400.1.5.1.5 | ColumnntcTsAnlyPcrPidMinJitter | read-only | current | Minimum value of PCR_AC (nanoseconds) over the last second. |
| 1.3.6.1.4.1.5835.5.2.1400.1.5.1.6 | ColumnntcTsAnlyPcrPidMaxJitter | read-only | current | Max Jitter PCR_AC (nanoseconds) measured over the last second. |
| 1.3.6.1.4.1.5835.5.2.1400.1.5.1.7 | ColumnntcTsAnlyPcrPidMinHoldJitter | read-only | current | The minimum measured PCR_AC value (in nanoseconds) computed since the last reset. |
| 1.3.6.1.4.1.5835.5.2.1400.1.5.1.8 | ColumnntcTsAnlyPcrPidMaxHoldJitter | read-only | current | The maximum measured PCR_AC value (in nanoseconds) computed since the last reset. |
| 1.3.6.1.4.1.5835.5.2.1400.1.5.1.9 | ColumnntcTsAnlyPcrPidRateOffset | read-only | current | Rate Offset in PPM of the inband clock companed to the local clock. (ASI: local clock, TS over IP: configured bitrate) |
| 1.3.6.1.4.1.5835.5.2.1400.1.5.1.10 | ColumnntcTsAnlyPcrPidPcrRate | read-only | current | PCR Rate (Mb/s) calculated by using the inband PCR timing information. |
| 1.3.6.1.4.1.5835.5.2.1400.1.6 | IdentityntcTsAnlyAlarm | current | Container holding ntcTsAnlyAlarm definitions. | |
| 1.3.6.1.4.1.5835.5.2.1400.1.6.1 | ScalarntcTsAnlyAlmSyncLoss | read-only | current | Alarm indicating that the synchronization with the Transport-Stream (TS) has been lost. This conditions occurs when 2 or more consecutive corrupted SYNC bytes … |
| 1.3.6.1.4.1.5835.5.2.1400.1.6.2 | ScalarntcTsAnlyAlmSyncByte | read-only | current | This alarm is raised when a single corrupted SYNC byte is detected and cleared when the next correct one appears. This variable indicates the current status of… |
| 1.3.6.1.4.1.5835.5.2.1400.1.6.3 | ScalarntcTsAnlyAlmPat | read-only | current | This alarm indicates that the 'Program Association Table' (PAT) can not be detected properly in the stream. The PAT table id (0x00) should be detected in a PID… |
| 1.3.6.1.4.1.5835.5.2.1400.1.6.4 | ScalarntcTsAnlyAlmContinuityCount | read-only | current | This alarm is raised when packets arrive out of sequence, get dropped or occur more than once. This variable indicates the current status of the alarm. |
| 1.3.6.1.4.1.5835.5.2.1400.1.6.5 | ScalarntcTsAnlyAlmTransport | read-only | current | This alarm condition is detected when the 'Transport Error indicator'-bit in the TS-Header is set to '1' for a specific PID. The alarm condition is cleared whe… |
| 1.3.6.1.4.1.5835.5.2.1400.1.6.6 | ScalarntcTsAnlyAlmPcrRepetition | read-only | current | This alarm is raised if the spacing between two consecutive PCR values is more than 40ms. The condition can occur when PCR packets get lost or when PCR packets… |
| 1.3.6.1.4.1.5835.5.2.1400.1.6.7 | ScalarntcTsAnlyAlmPcrDiscontinuity | read-only | current | This alarm indicates that the difference between two consecutive PCR values exceeds the range [0-100] ms, while the 'discontinuity indicator' bit is not set. T… |
| 1.3.6.1.4.1.5835.5.2.1400.1.6.8 | ScalarntcTsAnlyAlmPcrAccuracy | read-only | current | This alarm condition occurs when the PCR accuracy exceeds +/- 500nsec. The definition of the alarm is taken from TR101290. This variable indicates the current … |
| 1.3.6.1.4.1.5835.5.2.1400.1.7 | TablentcTsAnlyEPidTable | not-accessible | current | Table which contains PIDs on which an error has been detected. |
| 1.3.6.1.4.1.5835.5.2.1400.1.7.1 | RowntcTsAnlyEPidEntry | not-accessible | current | A conceptual row of the ntcTsAnlyEPidTable. |
| 1.3.6.1.4.1.5835.5.2.1400.1.7.1.1 | ColumnntcTsAnlyEPidPid | not-accessible | current | PID |
| 1.3.6.1.4.1.5835.5.2.1400.1.7.1.2 | ColumnntcTsAnlyEPidType | read-only | current | PID Type |
| 1.3.6.1.4.1.5835.5.2.1400.1.7.1.3 | ColumnntcTsAnlyEPidCtuCntErrorCntr | read-only | current | Indicates the number of packets with a continuity count error. |
| 1.3.6.1.4.1.5835.5.2.1400.1.7.1.4 | ColumnntcTsAnlyEPidContinuityError | read-only | current | Continuity Count Error |
| 1.3.6.1.4.1.5835.5.2.1400.1.7.1.5 | ColumnntcTsAnlyEPidTransportError | read-only | current | Transport Error |
| 1.3.6.1.4.1.5835.5.2.1400.2 | IdentityntcTsAnlyConformance | current | Conformance requirements. | |
| 1.3.6.1.4.1.5835.5.2.1400.2.1 | IdentityntcTsAnlyConfCompliance | current | Device compliance statements. | |
| 1.3.6.1.4.1.5835.5.2.1400.2.1.1 | CompliancentcTsAnlyConfCompV1Standard | current | Compliance statement for Newtec device MIB implementations. | |
| 1.3.6.1.4.1.5835.5.2.1400.2.2 | IdentityntcTsAnlyConfGroup | current | Groups used by device compliance statements. | |
| 1.3.6.1.4.1.5835.5.2.1400.2.2.1 | GroupntcTsAnlyConfGrpV1Standard | current | Managed objects that constitute version 1 of a system device with standard capabilities. |