NTWS-AP-TC
34 objects
Textual Conventions used by Nortel Networks wireless switches. AP = Access Point; AC = Access Controller (wireless switch), the device that runs a SNMP Agent using these TCs. Copyright 2009 Nortel Networks. All rights reserved. This Nortel Networks SNMP Management Information Base Specification (Specification) embodies Nortel Networks' confidential and proprietary intellectual property. This Specification is supplied 'AS IS' and Nortel Networks makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
Imported Objects
| NTWS-ROOT-MIB | ntwsMibs |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY Unsigned32 |
| SNMPv2-TC | TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.45.6.1.4.3 | IdentityntwsApTc | Textual Conventions used by Nortel Networks wireless switches. AP = Access Point; AC = Access Controller (wireless switch), the device that runs a SNMP Agent u… |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| NtwsAccessType | INTEGER { ap (1), dap (2), wired (3) } | current | Describes the access type used by client or an AP. Value 'ap(1)' indicates access point that is directly attached to the switch. Value 'dap(2)' indicates distributed access point with attachment to the switch through th… |
| NtwsApAttachType | INTEGER { directAttach(1), networkAttach(2) } | current | Type of AP attachment to AC. |
| NtwsApBias | INTEGER { high(1), low(2), sticky(3) } | current | Bias of AP attachment to this AC. Setting an APs bias on an AC switch to high causes the switch to be preferred over switches with low bias, for booting and managing the AP. Bias applies only to AC switches that are ind… |
| NtwsApConnectSecurityType | INTEGER { secure (1), insecure (2), auto (3) } | current | Security level of the connection between AP and AC: secure(1) - fingerprint matching; insecure(2) - fingerprint not configured, or optional and not matching; auto(3) - Auto-DAP is intrinsically insecure: could not check… |
| NtwsApFailDetail | INTEGER { secureHandshakeFailure (2), fingerprintRequired (3), fingerprintMismatch (4), portLinkUp (11), portLinkDown (12), normalTransition (91), failUnknown (99) } | current | Detailed failure codes for some of the transitions specified in 'NtwsApTransition'. - 'normalTransition' (91) means the corresponding transition is not a failure; could be caused by an explicit request (for example, AP … |
| NtwsApFingerprint | OCTET STRING (SIZE (0 | 16)) | current | Represents a RSA key fingerprint (binary value), which is the MD5 hash of the public key of the RSA key pair. Or a zero length string if not known or unavailable. |
| NtwsApLedMode | INTEGER { auto (1), static (2), off (3) } | current | Enumeration to indicate the administratively controlled LED mode for an AP. |
| NtwsApNum | Unsigned32 (0..9999) | current | AP Number: arbitrary number assigned when configuring the AP on the AC. It is unique (on same AC), regardless of the type of AP attachment. A zero value means unknown. |
| NtwsApPortOrDapNum | Unsigned32 (0..1000) | obsolete | AP Port, for directly attached APs, otherwise DAP Number (arbitrary number assigned when configuring the DAP on the AC). A zero value means unknown. Obsoleted by NtwsApNum. (In 6.0, direct- and network-attached APs were… |
| NtwsApPowerMode | INTEGER { auto (1), high (2) } | current | Enumerations of the modes in which power is supplied by the AP to its components (mainly radios). There are two administratively controlled values: - auto: the power is managed automatically by sensing the power level o… |
| NtwsApRadioIndex | Unsigned32 (1..4294967295) | current | A unique value, greater than zero, for each Radio on the AP. Intended to replace NtwsRadioNum. |
| NtwsApRadioIndexOrZero | Unsigned32 (0 | 1..4294967295) | current | This textual convention is an extension of the NtwsApRadioIndex convention. The latter defines a greater than zero value used to identify each Radio on the AP. This extension permits the additional value of zero. A zero… |
| NtwsApSerialNum | OCTET STRING (SIZE (0..32)) | current | The value is a zero length string if unknown or unavailable. Otherwise the value is a serial number, which consists of printable ASCII characters between 0x21 (!), and 0x7d (}) with no leading, embedded, or trailing spa… |
| NtwsApServiceAvailability | INTEGER { fullService (1), noService (2), degradedService (3) } | current | Level of wireless service availability. |
| NtwsApState | INTEGER { cleared (1), init (2), bootStarted (3), imageDownloaded (4), connectFailed (5), configuring (6), configured (7) } | current | AP State, as seen by the AC. |
| NtwsApTransition | INTEGER { clear (1), timeout (2), reset (3), bootSuccess (4), startConfiguring (5), connectFail (6) } | current | AP state Transition, as seen by the AC. |
| NtwsApWasOperational | INTEGER { oper (1), nonOper (2) } | current | Enumeration to indicate whether the AP was operational before a transition occurred. Normally used in notifications. |
| NtwsChannelChangeType | INTEGER { util-index (1), rexmit-pkt-offset (2), noise-offset (3), noise (4), utilization (5), phy-error-offset (6), crc-errors-offset (7), radar-detected (8) } | current | Enumerations for why the channel was changed, which occurs due to auto-tune operation |
| NtwsChannelNum | Unsigned32 (1..1024) | current | Channel Number |
| NtwsCryptoType | INTEGER { other (1), clear (2), wep (3), wep40 (4), wep104 (5), tkip (6), aesCcmp (7) } | current | Enumeration of Crypto Types: - clear: Cleartext (unencrypted communication); - wep: Wired Equivalent Privacy; - wep40: WEP with 40-bit keys; - wep104: WEP with 104-bit keys; - tkip: Temporal Key Integrity Protocol; - ae… |
| NtwsPowerLevel | Unsigned32 | current | The current level of transmit power expressed in dbm. |
| NtwsRadioAntennaLocation | INTEGER { indoors (1), outdoors (2) } | current | Enumeration to indicate the administratively controlled Radio Antenna Location. |
| NtwsRadioChannelWidth | INTEGER { channelWidth20MHz (1), channelWidth40MHz (2) } | current | Enumeration to indicate the administratively controlled Radio Channel Width. |
| NtwsRadioConfigState | INTEGER { configInit (1), configFail (2), configOk (3) } | current | Radio Configuration State, as seen by the AC. |
| NtwsRadioEnable | INTEGER { enabled (1), disabled (2) } | obsolete | Radio mode (administratively enabled or disabled). Obsoleted by NtwsRadioMode. |
| NtwsRadioMimoState | INTEGER { mimoOther (1), mimo1x1 (2), mimo2x3 (3), mimo3x3 (4) } | current | Enumeration to indicate the MIMO state of the Radio (Multiple Input Multiple Output), as seen by the AC. This depends on radio type and power supplied to the radio. mimo1x1: radio uses one transmit chain and one receive… |
| NtwsRadioMode | INTEGER { enabled (1), disabled (2), sentry (3) } | current | Configured mode of an AP radio. There are three administratively controlled values: - enabled: radio may provide service to clients; - sentry: radio will not provide service, but can be used for RF scanning and can run … |
| NtwsRadioNum | INTEGER { radio-1 (1), radio-2 (2), not-applicable (3) } | current | Enumeration for multi-radio APs. |
| NtwsRadioPowerChangeType | INTEGER { dup-pkts-threshold-exceed (1), retransmit-threshold-exceed (2), clients-optimal-performance-reached (3), def-power-threshold-exceed (4) } | current | Enumerations for why the power level was changed, which occurs due to auto-tune operation. |
| NtwsRadioRate | Unsigned32 (0 | 10..540) | current | The possible transmission rates of an AP radio. Both a and b/g rates are covered; a specific radio will report the applicable transmission rates (either a or b/g). Here are the possible rates, in Mbps: - 802.11g radios:… |
| NtwsRadioRateEx | INTEGER { rateUnknown (1), rate1 (2), rate2 (3), rate5-5 (4), rate6 (5), rate9 (6), rate11 (7), rate12 (8), rate18 (9), rate24 (10), rate36 (11), rate48 (12), rate54 (13), rateMCS0 (20), rateMCS1 (21), rateMCS2 (22), rateMCS3 (23), rateMCS4 (24), rateMCS5 (25), rateMCS6 (26), rateMCS7 (27), rateMCS8 (28), rateMCS9 (29), rateMCS10 (30), rateMCS11 (31), rateMCS12 (32), rateMCS13 (33), rateMCS14 (34), rateMCS15 (35) } | current | Radio Rates Extended (covering 11n MCS rates): The possible transmission rates of an AP radio. 11a, 11b/g, 11na and 11ng rates are included; a specific radio will report the applicable transmission rates (either a, b/g,… |
| NtwsRadioType | INTEGER { typeUnknown (1), typeA (2), typeB (3), typeG (4), typeNA (5), typeNG (6) } | current | Enumeration to indicate the Radio Type, as seen by AC. |
| NtwsRssi | Integer32 (-100..0) | current | RSSI (Received Signal Strength Indicator) for last packet received, in decibels referred to 1 milliwatt (dBm). A higher value indicates a stronger signal. |