OADWDM-MIB
486 objects
No module-level DESCRIPTION found.
Imported Objects
| OA-TRAP-MESSAGES-MIB | oaDevTrapsPortsIfAlias |
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | Counter enterprises |
| RFC1213-MIB | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.6926 | Nodeoaccess | |||
| 1.3.6.1.4.1.6926.1 | NodeoaManagement | |||
| 1.3.6.1.4.1.6926.1.41 | NodeoaLambdaDriver | |||
| 1.3.6.1.4.1.6926.1.41.1 | NodeoaLdDevIdentify | |||
| 1.3.6.1.4.1.6926.1.41.1.1 | ScalaroaLdNSlots | read-only | mandatory | The number of slots in this device |
| 1.3.6.1.4.1.6926.1.41.1.2 | ScalaroaLdCardHardVers | read-only | mandatory | Hardware version of the agent card |
| 1.3.6.1.4.1.6926.1.41.1.3 | ScalaroaLdSoftVers | read-only | mandatory | Agent software version |
| 1.3.6.1.4.1.6926.1.41.1.4 | ScalaroaLdCreatinDate | read-only | mandatory | Agent software creation date and time |
| 1.3.6.1.4.1.6926.1.41.1.5 | ScalaroaLdDeviceType | read-only | mandatory | Device type |
| 1.3.6.1.4.1.6926.1.41.1.6 | ScalaroaLdCardFpgaVers | read-only | mandatory | FPGA version of the agent card |
| 1.3.6.1.4.1.6926.1.41.1.7 | ScalaroaLdCardBackplaneVers | read-only | mandatory | Chassis backplane version. Value = -1 says, this object is not supported. |
| 1.3.6.1.4.1.6926.1.41.1.8 | ScalaroaLdTrapsVer | read-write | mandatory | Traps format version. If this object is not suppoted or its value is 1, the traps version is the origin one, traps 15,17,20,23,25,27,28 and 29 are sent. If thi… |
| 1.3.6.1.4.1.6926.1.41.1.9 | ScalaroaLdCpuCardSerialNumber | read-only | mandatory | The CPU Card's Serial Number (10 digits). |
| 1.3.6.1.4.1.6926.1.41.1.10 | NodeoaLdDevGenConfig | |||
| 1.3.6.1.4.1.6926.1.41.1.10.1 | NodeoaLdDevPS | |||
| 1.3.6.1.4.1.6926.1.41.1.10.1.1 | ScalaroaLdDevPSNumber | read-only | mandatory | The number of Power Supplies in the corresponding Device. Value = 0 says, that Power Supply Table is not supported. |
| 1.3.6.1.4.1.6926.1.41.1.10.1.2 | TableoaLdDevPSTable | not-accessible | mandatory | This table shows all the Power Supplies modules, existing in the corresponding Device. |
| 1.3.6.1.4.1.6926.1.41.1.10.1.2.1 | RowoaLdDevPSEntry | not-accessible | mandatory | The entries of the table. |
| 1.3.6.1.4.1.6926.1.41.1.10.1.2.1.1 | ColumnoaLdDevPSIndex | read-only | mandatory | The index of the table, (MAX Value is equal to oaLdDevPSNumber). |
| 1.3.6.1.4.1.6926.1.41.1.10.1.2.1.5 | ColumnoaLdDevPSOperStatus | read-only | mandatory | The Oper status of the Power Supply. |
| 1.3.6.1.4.1.6926.1.41.1.10.1.2.1.6 | ColumnoaLdDevPSPartNumber | read-only | mandatory | The Part Number of the Power Supply(maximum 15 symbols). |
| 1.3.6.1.4.1.6926.1.41.1.10.1.2.1.7 | ColumnoaLdDevPSSerialNumber | read-only | mandatory | The Serial Number of the Power Supply(10 digits). |
| 1.3.6.1.4.1.6926.1.41.1.10.1.2.1.8 | ColumnoaLdDevPSHwRev | read-only | mandatory | The Hardware Revision of the Power Supply. |
| 1.3.6.1.4.1.6926.1.41.1.10.3 | NodeoaLdDevFAN | |||
| 1.3.6.1.4.1.6926.1.41.1.10.3.1 | ScalaroaLdDevFANsNumber | read-only | mandatory | The number of FANS in the corresponding Device. Value = 0 says, that FAN Table is not supported. |
| 1.3.6.1.4.1.6926.1.41.1.10.3.2 | TableoaLdDevFANTable | not-accessible | mandatory | This table shows all the FANs existing in the corresponding Device. |
| 1.3.6.1.4.1.6926.1.41.1.10.3.2.1 | RowoaLdDevFANEntry | not-accessible | mandatory | The entries of the table. |
| 1.3.6.1.4.1.6926.1.41.1.10.3.2.1.1 | ColumnoaLdDevFANIndex | read-only | mandatory | The index of the table, (MAX Value is equal to oaLdDevFANsNumber). |
| 1.3.6.1.4.1.6926.1.41.1.10.3.2.1.5 | ColumnoaLdDevFANOperStatus | read-only | mandatory | The Oper status of the FAN. |
| 1.3.6.1.4.1.6926.1.41.1.10.4 | NodeoaLdDevCPU | |||
| 1.3.6.1.4.1.6926.1.41.1.10.4.1 | ScalaroaLdDevCPUNumber | read-only | mandatory | The number of CPU modules in the corresponding Device. |
| 1.3.6.1.4.1.6926.1.41.1.10.4.10 | TableoaLdDevCPUTable | not-accessible | mandatory | This table shows all the CPU modules, existing in the corresponding Device. |
| 1.3.6.1.4.1.6926.1.41.1.10.4.10.1 | RowoaLdDevCPUEntry | not-accessible | mandatory | The entries of the table. |
| 1.3.6.1.4.1.6926.1.41.1.10.4.10.1.1 | ColumnoaLdDevCPUIndex | read-only | mandatory | The index of the table, (MAX Value is equal to oaLdDevCPUNumber). |
| 1.3.6.1.4.1.6926.1.41.1.10.4.10.1.2 | ColumnoaLdDevCPUOperStatus | read-only | mandatory | The Operative status of the CPU module. active - single CPU module or master CPU module in chassis with redundant CPU; standby - slave CPU module in chassis wi… |
| 1.3.6.1.4.1.6926.1.41.1.10.4.10.1.3 | ColumnoaLdDevCPUType | read-only | mandatory | The HW Type of the CPU module. mgtd - regular agent module; mgtp - power agent module with additional HW features; mngt - KW based agent module. |
| 1.3.6.1.4.1.6926.1.41.1.10.4.10.1.4 | ColumnoaLdDevCPUHardVers | read-only | mandatory | The CPU Card's hardware version. |
| 1.3.6.1.4.1.6926.1.41.1.10.4.10.1.5 | ColumnoaLdDevCPUFpgaVers | read-only | mandatory | The CPU Card's FPGA version. |
| 1.3.6.1.4.1.6926.1.41.1.10.4.10.1.6 | ColumnoaLdDevCPUSerialNumber | read-only | mandatory | The CPU Card's Serial Number (10 digits). |
| 1.3.6.1.4.1.6926.1.41.1.10.4.10.1.7 | ColumnoaLdDevCPUBuildTime | read-only | mandatory | Agent software creation date and time. |
| 1.3.6.1.4.1.6926.1.41.1.10.4.10.1.8 | ColumnoaLdDevCPUSoftVers | read-only | mandatory | Agent software version. |
| 1.3.6.1.4.1.6926.1.41.1.10.4.10.1.9 | ColumnoaLdDevCPUBoardID | read-only | mandatory | ID of CPU's base card |
| 1.3.6.1.4.1.6926.1.41.1.10.4.10.1.10 | ColumnoaLdDevCPUBoardHardVers | read-only | mandatory | Hardware version of CPU's base card |
| 1.3.6.1.4.1.6926.1.41.1.10.5 | NodeoaLdDevRedundantCPU | |||
| 1.3.6.1.4.1.6926.1.41.1.10.5.1 | ScalaroaLdDevRedundantFeature | read-write | mandatory | Set Redundant CPU feature on the next boot in the corresponding Device. |
| 1.3.6.1.4.1.6926.1.41.1.10.5.2 | ScalaroaLdDevRedundantMode | read-write | mandatory | Set Redundant CPU mode in the corresponding Device. |
| 1.3.6.1.4.1.6926.1.41.1.10.5.3 | ScalaroaLdDevRedundantCommand | read-write | mandatory | Force a command in the corresponding Device. forceSwitchOver - Force Standby CPU module to become Active; forceSync - Force configuration sync with Standby sys… |
| 1.3.6.1.4.1.6926.1.41.1.10.5.4 | ScalaroaLdDevRedundantPeerAdminStatus | read-write | mandatory | Force a command to Slave (peer) CPU module in the corresponding Device. recover - recover peer CPU module by hardware reset; reboot - reboot peer CPU module; s… |
| 1.3.6.1.4.1.6926.1.41.1.11 | NodeoaLdDevGenIdentify | |||
| 1.3.6.1.4.1.6926.1.41.1.11.1 | ScalaroaLdCardBackplaneSN | read-only | mandatory | Chassis backplane's Serial Number (10 digits). |
| 1.3.6.1.4.1.6926.1.41.1.11.2 | ScalaroaLdSoftVersString | read-only | mandatory | Agent software version in string presentation |
| 1.3.6.1.4.1.6926.1.41.1.11.3 | ScalaroaLdCardBackplanePN | read-only | mandatory | Chassis backplane's Part Number (maximum 15 digits). |
| 1.3.6.1.4.1.6926.1.41.1.11.4 | ScalaroaLdCardIftableExtMode | read-write | mandatory | Interface fTable extention mode. |
| 1.3.6.1.4.1.6926.1.41.2 | NodepowerSupplyUpLD | The SNMP trap that is generated when power supply unit changes it's state from notActive to active | ||
| 1.3.6.1.4.1.6926.1.41.3 | NodeoaLdSlotsStatTable | |||
| 1.3.6.1.4.1.6926.1.41.3 | NodepowerSupplyDownLD | The SNMP trap that is generated when power supply unit changes it's state from active to notActive | ||
| 1.3.6.1.4.1.6926.1.41.3.1 | TableoaLdCardsStatTable | not-accessible | mandatory | A list of all the slots status objects |
| 1.3.6.1.4.1.6926.1.41.3.1.1 | RowoaLdCardsStatEntry | not-accessible | mandatory | The slots status information. |
| 1.3.6.1.4.1.6926.1.41.3.1.1.1 | ColumnoaLdCardIndex | read-only | mandatory | The slot#. An index from 1 to The number of slots. |
| 1.3.6.1.4.1.6926.1.41.3.1.1.2 | ColumnoaLdCardType | read-only | mandatory | The Card's type |
| 1.3.6.1.4.1.6926.1.41.3.1.1.3 | ColumnoaLdCardRev | read-only | mandatory | The Card's Revision |
| 1.3.6.1.4.1.6926.1.41.3.1.1.4 | ColumnoaLdCardLambdaCh | read-only | mandatory | The Card's Lambda channel |
| 1.3.6.1.4.1.6926.1.41.3.1.1.5 | ColumnoaLdCardOptAccRx | read-only | mandatory | Slot optic access Rx indication. Indicates the optic access Receive status 2 - Receive On 3 - Receive Off |
| 1.3.6.1.4.1.6926.1.41.3.1.1.6 | ColumnoaLdCardOptDwdmRx | read-only | mandatory | Slot optic DWDM Rx indication. Indicates the optic DWDM Receive status 2 - Receive On 3 - Receive Off |
| 1.3.6.1.4.1.6926.1.41.3.1.1.7 | ColumnoaLdCardDwdmLaserTx | read-only | mandatory | Slot DWDM Laser Tx Fail indication. Indicates the DWDM Laser Transmit status 2 - Transmit OK 3 - Transmit Fail |
| 1.3.6.1.4.1.6926.1.41.3.1.1.8 | ColumnoaLdCardLaserTemp | read-only | mandatory | Slot Laser Temperature indication. Indicates the Laser Temperature status 2 - Temperature Normal 3 - Temperature High |
| 1.3.6.1.4.1.6926.1.41.3.1.1.9 | ColumnoaLdCardAmbientTemp | read-only | mandatory | Slot Ambient Temperature indication. Indicates the Ambient Temperature status 2 - Temperature Normal 3 - Temperature High |
| 1.3.6.1.4.1.6926.1.41.3.1.1.10 | ColumnoaLdCardRateSelect | read-write | mandatory | Transponder Rate Select. Indicates the transponder rate. oc48, stm16 and fiberChannel2125 are for card EM2009-CH and EM2009-DH only. sonetSdh10giga and fiberCh… |
| 1.3.6.1.4.1.6926.1.41.3.1.1.11 | ColumnoaLdCardRateMode | read-only | mandatory | Transponder Rate Mode. Indicates the transponder rate mode. 2 - Automatic - Rate is set by software 3 - Manual - Rate is set by DIP switches on board If manual… |
| 1.3.6.1.4.1.6926.1.41.3.1.1.12 | ColumnoaLdCardLaserMode | read-write | mandatory | Transponder Laser Mode. Indicates the transponder laser mode. 2 - Enable - Laser is enabled 3 - Disable - Laser is disabled (can not transmit) |
| 1.3.6.1.4.1.6926.1.41.3.1.1.15 | ColumnoaLdCardWdmRxPm | read-only | mandatory | Transponder WDM receiver optical power. Indicates the optical power in dBm. To calculate the power use the equation P(dBm)=oaLdCardWdmRxPm/2, when oaLdCardWdmR… |
| 1.3.6.1.4.1.6926.1.41.3.1.1.16 | ColumnoaLdCardWdmTxPm | read-only | mandatory | Transponder WDM transmitter optical power. Indicates the optical power in dBm. To calculate the power use the equation P(dBm)=oaLdCardWdmTxPm/2, when oaLdCardW… |
| 1.3.6.1.4.1.6926.1.41.3.1.1.17 | ColumnoaLdCardLoopBack | read-write | mandatory | Transponder LoopBack state. Indicates the transponder LoopBack state. 2 - normal - Transponder card is in non-loopback state 3 - loopback - Transponder card is… |
| 1.3.6.1.4.1.6926.1.41.3.1.1.18 | ColumnoaLdCardRedundantState | read-only | mandatory | Transponder Redundant Mode. Indicates the transponder redundant mode. 2 - normal - Transponder is in non-redundant mode 3 - redundant - Transponder is in redun… |
| 1.3.6.1.4.1.6926.1.41.3.1.1.19 | ColumnoaLdCardPrimaryState | read-write | mandatory | Transponder Primary/Secondary State. Indicates the transponder Primary/Secondary status. 2 - secondary - Transponder is in secondary state and is not active 3 … |
| 1.3.6.1.4.1.6926.1.41.3.1.1.20 | ColumnoaLdCardFPGARev | read-only | mandatory | The Card's FPGA Revision |
| 1.3.6.1.4.1.6926.1.41.3.1.1.21 | ColumnoaLdCardPartNumber | read-only | mandatory | The Card's Part Number (maximum 15 symbols). |
| 1.3.6.1.4.1.6926.1.41.3.1.1.22 | ColumnoaLdCardSerialNumber | read-only | mandatory | The Card's Serial Number (10 digits). |
| 1.3.6.1.4.1.6926.1.41.3.1.1.23 | ColumnoaLdCardHwRev | read-only | mandatory | The Card's Hardware Revision |
| 1.3.6.1.4.1.6926.1.41.3.1.1.24 | ColumnoaLdCardOptAccTx | read-only | mandatory | Slot optic access Tx indication. Indicates the optic access Transmit status 2 - Transmit On 3 - Transmit Off |
| 1.3.6.1.4.1.6926.1.41.3.1.1.25 | ColumnoaLdCardOptDwdmTx | read-only | mandatory | Slot optic DWDM Tx indication. Indicates the optic DWDM Transmit status 2 - Transmit On 3 - Transmit Off |
| 1.3.6.1.4.1.6926.1.41.3.1.1.26 | ColumnoaLdCardTemp | read-only | mandatory | The Module Temperature (in units of 1/10 Degrees Celsius [0.1 C]) |
| 1.3.6.1.4.1.6926.1.41.3.1.1.27 | ColumnoaLdCardSubType | read-only | mandatory | The Card's subtype |
| 1.3.6.1.4.1.6926.1.41.4 | NodeoaLdSlotEntitysStat | |||
| 1.3.6.1.4.1.6926.1.41.4 | NodepowerSupplyInLD | The SNMP trap that is generated when power supply unit is inserted into the chassis | ||
| 1.3.6.1.4.1.6926.1.41.4.1 | TableoaLdCardEntityStatTable | not-accessible | mandatory | A list of all Entities in a slot and their status objects |
| 1.3.6.1.4.1.6926.1.41.4.1.1 | RowoaLdCardEntityStatEntry | not-accessible | mandatory | The slots Entity status information. |
| 1.3.6.1.4.1.6926.1.41.4.1.1.1 | ColumnoaLdCardEntityCardIndex | read-only | mandatory | The slot#. An index from 1 to The number of slots. |
| 1.3.6.1.4.1.6926.1.41.4.1.1.2 | ColumnoaLdCardEntityEntityIndex | read-only | mandatory | The entity#. An index from 1 to The number of entities. |
| 1.3.6.1.4.1.6926.1.41.4.1.1.5 | ColumnoaLdCardEntityWaveLength | read-only | mandatory | The Card's entity laser wavelength (Lambda channel) in units of nm (Nanometer). Returns 0 when not applicable |
| 1.3.6.1.4.1.6926.1.41.4.1.1.6 | ColumnoaLdCardEntityOptAccRx | read-only | mandatory | Entity optic access Rx indication. Indicates the optic access Receive status 2 - Receive On 3 - Receive Off |
| 1.3.6.1.4.1.6926.1.41.4.1.1.7 | ColumnoaLdCardEntityOptDwdmRx | read-only | mandatory | Entity optic DWDM Rx indication. Indicates the optic DWDM Receive status 2 - Receive On 3 - Receive Off |
| 1.3.6.1.4.1.6926.1.41.4.1.1.8 | ColumnoaLdCardEntityDwdmLaserTx | read-only | mandatory | Entity DWDM Laser Tx Fail indication. Indicates the DWDM Laser Transmit status 2 - Transmit OK 3 - Transmit Fail |
| 1.3.6.1.4.1.6926.1.41.4.1.1.9 | ColumnoaLdCardEntityLaserTemp | read-only | mandatory | Entity Laser Temperature indication. Indicates the Laser Temperature status 2 - Temperature Normal 3 - Temperature High |
| 1.3.6.1.4.1.6926.1.41.4.1.1.10 | ColumnoaLdCardEntityAmbientTemp | read-only | mandatory | Entity Ambient Temperature indication. Indicates the Ambient Temperature status 2 - Temperature Normal 3 - Temperature High |
| 1.3.6.1.4.1.6926.1.41.4.1.1.11 | ColumnoaLdCardEntityRateSelect | read-write | mandatory | Transponder Rate Select. Indicates the transponder rate. oc48, stm16 and fiberChannel2125 are for card EM2009-CH and EM2009-DH only |
| 1.3.6.1.4.1.6926.1.41.4.1.1.12 | ColumnoaLdCardEntityRateMode | read-only | mandatory | Transponder Rate Mode. Indicates the transponder rate mode. 2 - Automatic - Rate is set by software 3 - Manual - Rate is set by DIP switches on board If manual… |
| 1.3.6.1.4.1.6926.1.41.4.1.1.13 | ColumnoaLdCardEntityLaserMode | read-write | mandatory | Transponder Laser Mode. Indicates the transponder laser mode. 2 - Enable - Laser is enabled 3 - Disable - Laser is disabled (can not transmit) |
| 1.3.6.1.4.1.6926.1.41.4.1.1.16 | ColumnoaLdCardEntityWdmRxPm | read-only | mandatory | Transponder WDM receiver optical power. Indicates the optical power in units of 1/10 dBm. (oaLdCardEntityWdmRxPm is a signed number.) (999) is returned when th… |
| 1.3.6.1.4.1.6926.1.41.4.1.1.17 | ColumnoaLdCardEntityWdmTxPm | read-only | mandatory | Transponder WDM transmitter optical power. Indicates the optical power in units of 1/10 dBm. (oaLdCardEntityWdmTxPm is a signed number.) (999) is returned when… |
| 1.3.6.1.4.1.6926.1.41.4.1.1.18 | ColumnoaLdCardEntityLoopBack | read-write | mandatory | Transponder LoopBack state. Indicates the transponder LoopBack state. 2 - normal - Transponder entity is in non-loopback state 3 - loopback - Transponder entit… |
| 1.3.6.1.4.1.6926.1.41.4.1.1.19 | ColumnoaLdCardEntityRedundantState | read-only | mandatory | Transponder Redundant Mode. Indicates the transponder redundant mode. 2 - normal - Transponder is in non-redundant mode 3 - redundant - Transponder is in redun… |
| 1.3.6.1.4.1.6926.1.41.4.1.1.20 | ColumnoaLdCardEntityPrimaryState | read-write | mandatory | Transponder Primary/Secondary State. Indicates the transponder Primary/Secondary status. 2 - secondary - Transponder is in secondary state and is not active 3 … |
| 1.3.6.1.4.1.6926.1.41.4.1.1.21 | ColumnoaLdCardEntityClockSource | read-write | mandatory | OCM Module Port Clock Source State. Indicates the Port Clock Source. 2 - Port 1 - Module Clock Source is port 1 3 - Port 2 - Module Clock Source is port 2 4 - … |
| 1.3.6.1.4.1.6926.1.41.4.1.1.22 | ColumnoaLdCardEntityTransparency | read-write | mandatory | OCM Module Transparency State. Indicates the Module transparency state. 2 - transparent - Module is in transparency mode 3 - no transparent - Module is in non … |
| 1.3.6.1.4.1.6926.1.41.4.1.1.23 | ColumnoaLdCardEntityStandard | read-write | mandatory | OCM Module Standard Mode. Indicates the Module Standard. 2 - sonet - Module in SONET standard mode 3 - sdh - Module in SDH standard mode |
| 1.3.6.1.4.1.6926.1.41.4.1.1.24 | ColumnoaLdCardEntityAccessLinState | read-write | mandatory | Transponder LIN status. Indicates the transponder access LIN status. 2 - Enable - Access LIN is enabled 3 - Disable - Access LIN is disabled |
| 1.3.6.1.4.1.6926.1.41.4.1.1.25 | ColumnoaLdCardEntityLineCoding | read-write | mandatory | Indicates the T1 cards Line Coding. 2 - B8ZS - Bipolar 8-zero substitution encoding 3 - AMI - Alternate Mark Inversion encoding |
| 1.3.6.1.4.1.6926.1.41.4.1.1.26 | ColumnoaLdCardEntityUartBaudRate | read-write | mandatory | Indicates the T1 cards UART Baud Rate configuration. |
| 1.3.6.1.4.1.6926.1.41.4.1.1.27 | ColumnoaLdCardEntityUartParity | read-write | mandatory | Indicates the T1 cards UART Parity configuration. |
| 1.3.6.1.4.1.6926.1.41.4.1.1.28 | ColumnoaLdCardEntityUartStopBit | read-write | mandatory | Indicates the T1 cards UART Stop Bit configuration. 1 - Stop Bit 1 x data bit, 2 - Stop Bit 1.5 x data bit. |
| 1.3.6.1.4.1.6926.1.41.4.1.1.29 | ColumnoaLdCardEntityPmMode | read-write | mandatory | Module Performance Monitoring Mode. Indicates the Module Performance Monitoring mode. 2 - Enable - PM is enabled 3 - Disable - PM is disabled |
| 1.3.6.1.4.1.6926.1.41.4.1.1.30 | ColumnoaLdCardEntityWdmFecMode | read-write | mandatory | The Forward Error Correction (FEC) mode which is used in the module. 2 - g709 - Standard G.709 FEC mode. 3 - eFec - Enhanced FEC proprietary mode. 4 - byPass -… |
| 1.3.6.1.4.1.6926.1.41.4.1.1.31 | ColumnoaLdCardEntityMinDispDist | read-only | mandatory | Minimum Dispersion distance of integrated TODC. (0) is returned when this feature is not supported Units: ps/nm |
| 1.3.6.1.4.1.6926.1.41.4.1.1.32 | ColumnoaLdCardEntityMaxDispDist | read-only | mandatory | Maximum Dispersion distance of integrated TODC. (0) is returned when this feature is not supported Units: ps/nm |
| 1.3.6.1.4.1.6926.1.41.4.1.1.33 | ColumnoaLdCardEntityDispDist | read-write | mandatory | Dispersion distance of integrated TODC. Units: ps/nm |
| 1.3.6.1.4.1.6926.1.41.4.1.1.34 | ColumnoaLdCardEntityCCMode | read-write | mandatory | EM1600-4CC10G Module cross connection mode. dual1234 - Dual transponder mode, when port 1 <-> 2, port 3 <-> 4. dual1324 - Dual transponder mode, when port 1 <-… |
| 1.3.6.1.4.1.6926.1.41.4.1.1.35 | ColumnoaLdCardEntityOptAccTx | read-only | mandatory | Entity optic access Tx indication. Indicates the optic access Transmit status 2 - Transmit On 3 - Transmit Off |
| 1.3.6.1.4.1.6926.1.41.4.1.1.36 | ColumnoaLdCardEntityOptDwdmTx | read-only | mandatory | Entity optic DWDM Tx indication. Indicates the optic DWDM Transmit status 2 - Transmit On 3 - Transmit Off |
| 1.3.6.1.4.1.6926.1.41.4.1.1.37 | ColumnoaLdCardEntityEMCfgType | read-write | mandatory | Specifies the E&M Lead Signaling type. |
| 1.3.6.1.4.1.6926.1.41.4.1.1.38 | ColumnoaLdCardEntityEMCfgSide | read-write | mandatory | Specifies the side of the unit: trunkCircuitSide - Trunk Circuit Side signalingUnitSide - Signaling Unit Side Usualy the PBX is the trunk circuit side and the … |
| 1.3.6.1.4.1.6926.1.41.4.1.1.39 | ColumnoaLdCardEntityPreemptionMode | read-write | mandatory | EM1600-4CC10G Module preemption mode for TX or RX Protection cross connect. In two following preemption modes one of access ports has priority to be active in … |
| 1.3.6.1.4.1.6926.1.41.4.1.1.40 | ColumnoaLdCardEntityActivePort | read-only | mandatory | EM1600-4CC10G Module actual active port for TX or RX Protection cross connect. |
| 1.3.6.1.4.1.6926.1.41.4.1.1.41 | ColumnoaLdCardEntityOperationMode | read-write | mandatory | other - Modue does not support this feature. normal- Normal operational mode. yCableRedundant - For TM2-XFP module redundancy mode. repeater - For TM2-XFPF mod… |
| 1.3.6.1.4.1.6926.1.41.4.1.1.42 | ColumnoaLdCardEntityRedundantType | read-write | mandatory | Redundant operation mode, (applicable only for modules that support this features) other - Module does not support this feature, normal - No redundant mode, du… |
| 1.3.6.1.4.1.6926.1.41.4.1.1.43 | ColumnoaLdCardEntityOtu2MappingMode | read-write | mandatory | For entities that enables mapping of clients into the OTN payload. The mode will indicate about the method of OTU-2 Line mapping. Based on that mode the user i… |
| 1.3.6.1.4.1.6926.1.41.4.1.1.44 | ColumnoaLdCardEntityTopologyMode | read-write | mandatory | |
| 1.3.6.1.4.1.6926.1.41.4.1.1.45 | ColumnoaLdCardEntityDispDistAdmin | read-write | mandatory | Administrative calibration factor for Dispersion distance of integrated TODC. Units: ps/nm |
| 1.3.6.1.4.1.6926.1.41.4.1.1.46 | ColumnoaLdCardEntityChannelOffset | read-write | mandatory | ITU channel offset. Units: GHz |
| 1.3.6.1.4.1.6926.1.41.4.1.1.47 | ColumnoaLdCardEntityTimingMode | read-write | mandatory | For entities that enables mapping of synchronous clients into the OTN payload. Timing mode will indicate how the clock will be recovered. none - Module does no… |
| 1.3.6.1.4.1.6926.1.41.4.1.1.48 | ColumnoaLdCardEntityTdcmTuningStatus | read-only | mandatory | Current tuning status. inProgress - not all etalons reach their target temperature values and some etalons are still tuning. ok - all etalons reach their targe… |
| 1.3.6.1.4.1.6926.1.41.4.1.1.49 | ColumnoaLdCardEntityRedModeActivePort | read-write | mandatory | For entities that support single slot redundancy with one access port. Active port specifies which of the acess ports is active. For TM2_XSFPFM Port#2 indicate… |
| 1.3.6.1.4.1.6926.1.41.4.1.1.50 | ColumnoaLdCardEntityAutoShutdownMode | read-write | mandatory | Entity Auto Shutdown Mode. Indicates the entity Auto Shutdown (eye safe) mode. 2 - Enable - Auto Shutdown mode is enabled 3 - Disable - Auto Shutdown mode is d… |
| 1.3.6.1.4.1.6926.1.41.5 | NodepowerSupplyOutLD | The SNMP trap that is generated when power supply unit is taken out of the chassis | ||
| 1.3.6.1.4.1.6926.1.41.6 | NodeoaLdRedundantOptic | |||
| 1.3.6.1.4.1.6926.1.41.6.1 | TableoaLdRedundantOpticTable | not-accessible | mandatory | Table of installed Lambda Driver Redundant Optical Cards |
| 1.3.6.1.4.1.6926.1.41.6.1.1 | RowoaLdRedundantOpticEntry | not-accessible | mandatory | Installed Lambda Driver Redundant Optical Cards |
| 1.3.6.1.4.1.6926.1.41.6.1.1.1 | ColumnoaLdRedOptSlotNumber | read-only | mandatory | The slot#. An index from 1 to The number of slots |
| 1.3.6.1.4.1.6926.1.41.6.1.1.2 | ColumnoaLdRedOptSwitchPosition | read-write | mandatory | Switch Position: 2 - Receive from Primary fiber. 3 - Receive from Secondary fiber. Note: a command to set the switch to a non received fiber will be ignored. |
| 1.3.6.1.4.1.6926.1.41.6.1.1.3 | ColumnoaLdRedOptLastCommand | read-only | mandatory | Indicates who issue the last command automatic - by hardware manual - by software |
| 1.3.6.1.4.1.6926.1.41.6.1.1.4 | ColumnoaLdRedOptPrimaryRx | read-only | mandatory | Indicates the Primary fiber Receive status 2 - Receive On 3 - Receive Off |
| 1.3.6.1.4.1.6926.1.41.6.1.1.5 | ColumnoaLdRedOptSecondaryRx | read-only | mandatory | Indicates the Secondary fiber Receive status 2 - Receive On 3 - Receive Off |
| 1.3.6.1.4.1.6926.1.41.8 | NodeoaLdCardPortsStat | |||
| 1.3.6.1.4.1.6926.1.41.8.1 | TableoaLdCardPortsStatTable | not-accessible | mandatory | Table of installed Lambda Driver Cards with more then one port |
| 1.3.6.1.4.1.6926.1.41.8.1.1 | RowoaLdCardPortsStatEntry | not-accessible | mandatory | Installed Lambda Driver Cards with more then one port |
| 1.3.6.1.4.1.6926.1.41.8.1.1.1 | ColumnoaLdCardPortsSlotNumber | read-only | mandatory | The slot#. An index from 1 to The number of slots |
| 1.3.6.1.4.1.6926.1.41.8.1.1.2 | ColumnoaLdCardPortsPortNumber | read-only | mandatory | The port#. An index from 1 to The number of ports |
| 1.3.6.1.4.1.6926.1.41.8.1.1.3 | ColumnoaLdCardPortsLink | read-only | mandatory | Indicates the link status of the port 2 - link on 3 - link off |
| 1.3.6.1.4.1.6926.1.41.8.1.1.4 | ColumnoaLdCardPortsActivity | read-only | mandatory | Indicates the activety status of the port 2 - activety on 3 - activety off |
| 1.3.6.1.4.1.6926.1.41.8.1.1.6 | ColumnoaLdCardPortsWaveLength | read-only | mandatory | The port laser wavelength (Lambda channel) in units of nm (Nanometer). Returns 0 when not applicable |
| 1.3.6.1.4.1.6926.1.41.8.1.1.8 | ColumnoaLdCardPortsLoopBack | read-write | mandatory | Transponder LoopBack state. Indicates the transponder LoopBack state. 2 - normal - Transponder card is in non-loopback state 3 - remoteLoopback - Transponder c… |
| 1.3.6.1.4.1.6926.1.41.8.1.1.12 | ColumnoaLdCardPortsCounters | read-write | mandatory | When read : 1 - Counter feature is NOT supported 2 - Counter feature is supported 4 - Extended ethernet counters are supported When write: 3 - Clear all port c… |
| 1.3.6.1.4.1.6926.1.41.8.1.1.14 | ColumnoaLdCardPortsCounter1Low | read-only | mandatory | The number of bytes received at the port. This object returns the least significant 32 bits of a 64 bits counter. To calculate the actual counter reading, use … |
| 1.3.6.1.4.1.6926.1.41.8.1.1.15 | ColumnoaLdCardPortsCounter1High | read-only | mandatory | The number of bytes received at the port. This object returns the most significant 32 bits of a 64 bits counter. To calculate the actual counter reading, use t… |
| 1.3.6.1.4.1.6926.1.41.8.1.1.17 | ColumnoaLdCardPortsCounter2Low | read-only | mandatory | The number of error bytes received at the port. This object returns the least significant 32 bits of a 64 bits counter. To calculate the actual counter reading… |
| 1.3.6.1.4.1.6926.1.41.8.1.1.18 | ColumnoaLdCardPortsCounter2High | read-only | mandatory | The number of error bytes received at the port. This object returns the most significant 32 bits of a 64 bits counter. To calculate the actual counter reading,… |
| 1.3.6.1.4.1.6926.1.41.8.1.1.20 | ColumnoaLdCardPortsConnectorType | read-only | mandatory | Port Connector Types: other - 1 - Unknown type of connector static- 2 - Not Changeable (fix) type of connector gbic - 3 - GBIC type of connector sfp - 4 - SFP … |
| 1.3.6.1.4.1.6926.1.41.8.1.1.21 | ColumnoaLdCardPortsConnectorSubType | read-only | mandatory | Port Connector Physical Sub Type: other -1 - Unknown or N/A Connector's connectivity Type rj45 -2 - Copper RJ45 sc -3 - Regular Fibre Optic [FO] lc -4 - LC mtr… |
| 1.3.6.1.4.1.6926.1.41.8.1.1.22 | ColumnoaLdCardPortsRate | read-write | mandatory | |
| 1.3.6.1.4.1.6926.1.41.8.1.1.23 | ColumnoaLdCardPortsLineLength | read-write | mandatory | T1 ports line length: other - 1 - Unknown line length from0to133 - 2 - line length 0 - 133 ft. (0.6 dB) from133to266 - 3 - line length 133 - 266 ft. (1.2 dB) f… |
| 1.3.6.1.4.1.6926.1.41.8.1.1.24 | ColumnoaLdCardPortsAccessLinState | read-write | mandatory | Port LIN status. Indicates the Port access LIN status. 2 - Enable - Access LIN is enabled 3 - Disable - Access LIN is disabled |
| 1.3.6.1.4.1.6926.1.41.8.1.1.25 | ColumnoaLdCardPortsFlowControlMode | read-write | mandatory | Module Flow Control Mode. Indicates the flow control mode for 10GbE access. 2 - Enable - Flow Control is enabled 3 - Disable - Flow Control is disabled |
| 1.3.6.1.4.1.6926.1.41.8.1.1.26 | ColumnoaLdCardPortsDryContactStat | read-only | mandatory | Port Dry Contact State. Indicates the Port Dry Contact State. 2 - open - Dry Contact is open 3 - close - Dry Contact is close |
| 1.3.6.1.4.1.6926.1.41.8.1.1.27 | ColumnoaLdCardPortsPowerTuning | read-write | mandatory | Port Power Tuning in dB of the E&M signal. (20) is returned if this value is undefined. |
| 1.3.6.1.4.1.6926.1.41.8.1.1.28 | ColumnoaLdCardPortsMediaType | read-only | mandatory | Type of Media. |
| 1.3.6.1.4.1.6926.1.41.8.1.1.29 | ColumnoaLdCardPortsEMCfgOperation | read-write | mandatory | Specify the operation of the E&M signal. twoWires - 2-wire operation. fourWires - 4-wire operation. |
| 1.3.6.1.4.1.6926.1.41.8.1.1.30 | ColumnoaLdCardPortsEyemaxState | read-write | mandatory | EyeMax state mode, (applicable only for ports that support this (EYEMAX) features) other - Port does not support this feature, disable - no Eyemax mode, scanni… |
| 1.3.6.1.4.1.6926.1.41.8.1.1.31 | ColumnoaLdCardPortsEyemaxOperFactor | read-only | mandatory | EyeMax Operational Calibrate factor, This value represents current DAC output. When this feature is not supported (0) is returned. Units: percent. |
| 1.3.6.1.4.1.6926.1.41.8.1.1.32 | ColumnoaLdCardPortsEyemaxAdminFactor | read-write | mandatory | EyeMax Administrative Calibration factor, This value is represents the value to be set into DAC. After scan operation it holds the optimal value that should be… |
| 1.3.6.1.4.1.6926.1.41.8.1.1.33 | ColumnoaLdCardPortsFefMode | read-write | mandatory | Port Far End Failure (FEF) Detection mode. 2 - Enable - FEF is enabled 3 - Disable - FEF is disabled |
| 1.3.6.1.4.1.6926.1.41.8.1.1.34 | ColumnoaLdCardPortsOdu1Index | read-write | mandatory | For clients that mapped into the OTN payload. Indicates the index of the OPU-1 payload area. 0 - not supported, or client is not configured. 1 - Client mapped … |
| 1.3.6.1.4.1.6926.1.41.8.1.1.35 | ColumnoaLdCardPortsOdu1TsIndex | read-write | mandatory | For clients that mapped into the OTN payload. Indicates the tributary slot index among the 16 tributary slots, of the OPU-1 payload area. 0 - not supported, or… |
| 1.3.6.1.4.1.6926.1.41.8.1.1.36 | ColumnoaLdCardPortsPmMode | read-write | mandatory | Port Performance Monitoring Mode. Indicates the Port Performance Monitoring mode. 2 - Enable - PM is enabled for this port 3 - Disable - PM is disabled for tth… |
| 1.3.6.1.4.1.6926.1.41.8.1.1.37 | ColumnoaLdCardPortsFecMode | read-write | mandatory | The Forward Error Correction (FEC) mode which is used in the selected port. 2 - g709 - Standard G.709 FEC mode. 3 - eFec - Enhanced FEC proprietary mode. 4 - b… |
| 1.3.6.1.4.1.6926.1.41.8.1.1.38 | ColumnoaLdCardPortsLock | read-only | mandatory | Port PLL lock mode. 2 - locked - PLL was locked, 3 - notlocked - PLL was not locked |
| 1.3.6.1.4.1.6926.1.41.8.1.1.39 | ColumnoaLdCardPortsLaserMode | read-write | mandatory | Port Laser Mode. Indicates the port laser mode. 2 - Enable - Laser is enabled 3 - Disable - Laser is disabled (can not transmit) |
| 1.3.6.1.4.1.6926.1.41.8.1.1.40 | ColumnoaLdCardPortsOdu1TsSize | read-only | mandatory | For clients that mapped into the OTN payload. Indicates the number of tributary slots that are occupied by the client's rate. 0 - not supported, or client is n… |
| 1.3.6.1.4.1.6926.1.41.8.1.1.41 | ColumnoaLdCardPortsSpeed | read-write | mandatory | Ports speed mode. |
| 1.3.6.1.4.1.6926.1.41.8.1.1.42 | ColumnoaLdCardPortsPriorityClockSource | read-write | mandatory | Defines the port's priority in relation to the clock source. 1 defines the highest priority index and the last port index defines the least prioritized port. T… |
| 1.3.6.1.4.1.6926.1.41.8.1.1.43 | ColumnoaLdCardPortsActionMode | read-write | mandatory | |
| 1.3.6.1.4.1.6926.1.41.8.1.1.44 | ColumnoaLdCardPortsOutputPortId | read-write | mandatory | |
| 1.3.6.1.4.1.6926.1.41.8.1.1.45 | ColumnoaLdCardPortsGroupId | read-write | mandatory | |
| 1.3.6.1.4.1.6926.1.41.8.1.1.46 | ColumnoaLdCardPortsChannelId | read-write | mandatory | |
| 1.3.6.1.4.1.6926.1.41.8.1.1.47 | ColumnoaLdCardPortsAutoShutdownMode | read-write | mandatory | Port Auto Shutdown Mode. Indicates the port Auto Shutdown (eye safe) mode. 2 - Enable - Auto Shutdown mode is enabled 3 - Disable - Auto Shutdown mode is disab… |
| 1.3.6.1.4.1.6926.1.41.8.1.1.48 | ColumnoaLdCardPortsEymxScnAmpFctr | read-write | mandatory | Initialization value for Amlification Factor used in the Eyemax scanning operation in 0.1 units. |
| 1.3.6.1.4.1.6926.1.41.8.1.1.49 | ColumnoaLdCardPortsEymxScnAmpFctrMin | read-only | mandatory | Minimum value that can be set for Initialization of the Amlification Factor used in the Eyemax scanning operation in 0.1 units. |
| 1.3.6.1.4.1.6926.1.41.8.1.1.50 | ColumnoaLdCardPortsEymxScnAmpFctrMax | read-only | mandatory | Maximum value that can be set for Initialization of the Amlification Factor used in the Eyemax scanning operation in 0.1 units. |
| 1.3.6.1.4.1.6926.1.41.8.1.1.51 | ColumnoaLdCardPortsEymxScnDspComps | read-write | mandatory | Initialization value for Dispersion Compensation used in the Eyemax scanning operation. |
| 1.3.6.1.4.1.6926.1.41.8.1.1.52 | ColumnoaLdCardPortsEymxScnTreshold | read-write | mandatory | Initialization value for Rx threshold used in the Eyemax scanning operation. |
| 1.3.6.1.4.1.6926.1.41.8.1.1.53 | ColumnoaLdCardPortsEymxScnOperComplt | read-only | mandatory | Indication how much of the scanning operation have been already completed (in percents 0 - 100). |
| 1.3.6.1.4.1.6926.1.41.8.1.1.54 | ColumnoaLdCardPortsEymxScnResult | read-only | mandatory | Indication if the scanning operation ended properly or finished with problems. |
| 1.3.6.1.4.1.6926.1.41.9 | NodeoaLdAdcCardInfo | |||
| 1.3.6.1.4.1.6926.1.41.9.2 | TableoaLdAdcCardInfoTable | not-accessible | mandatory | Table of installed Lambda Driver ADC / ADCD and MUX / DMUX Cards |
| 1.3.6.1.4.1.6926.1.41.9.2.1 | RowoaLdAdcCardInfoEntry | not-accessible | mandatory | Installed Lambda Driver ADC / ADCD and MUX / DMUX Cards |
| 1.3.6.1.4.1.6926.1.41.9.2.1.1 | ColumnoaLdAdcCardSlotNumber | read-only | mandatory | The slot#. An index from 1 to The number of slots |
| 1.3.6.1.4.1.6926.1.41.9.2.1.2 | ColumnoaLdAdcCardNumberOfPorts | read-only | mandatory | Number of ports at ADC / ADCD and MUX / DMUX card. For MUX / DMUX card the object returns the number of channels at card. Value = 0 says, that ADC / ADCD and M… |
| 1.3.6.1.4.1.6926.1.41.9.2.1.3 | ColumnoaLdAdcCardWdmWaveLength | read-only | mandatory | WDM Wave Length at ADC / ADCD and MUX / DMUX card. (CWDM or DWDM) |
| 1.3.6.1.4.1.6926.1.41.9.2.1.4 | ColumnoaLdAdcCardCardType | read-only | mandatory | WDM Card Type. |
| 1.3.6.1.4.1.6926.1.41.9.2.1.5 | ColumnoaLdAdcCardSpacing | read-only | mandatory | MUX / DMUX card - steps in channel spacing (in GHz) according to ITU-T. |
| 1.3.6.1.4.1.6926.1.41.9.2.1.6 | ColumnoaLdAdcCardSubBand | read-only | mandatory | MUX / DMUX card sub-band. Note: according to oaLdAdcCardSpacing and oaLdAdcCardSubBand it is able to know each channel wavelength. |
| 1.3.6.1.4.1.6926.1.41.9.2.1.7 | ColumnoaLdAdcCardChannelsPerPort | read-only | mandatory | Number of channels per port at OADM-XX / BS-XX card. For ADC / ADCD / MUX / DMUX card the object returns 1. |
| 1.3.6.1.4.1.6926.1.41.9.4 | TableoaLdAdcCardPortsInfoTable | not-accessible | mandatory | Table of installed Lambda Driver ADC and ADCD Cards |
| 1.3.6.1.4.1.6926.1.41.9.4.1 | RowoaLdAdcCardPortsInfoEntry | not-accessible | mandatory | Installed Lambda Driver ADC and ADCD Cards |
| 1.3.6.1.4.1.6926.1.41.9.4.1.1 | ColumnoaLdAdcCardPortsSlotNumber | read-only | mandatory | The slot#. An index from 1 to The number of slots |
| 1.3.6.1.4.1.6926.1.41.9.4.1.2 | ColumnoaLdAdcCardPortsPortNumber | read-only | mandatory | The port#. An index from 1 to The number of ports |
| 1.3.6.1.4.1.6926.1.41.9.4.1.3 | ColumnoaLdAdcCardPortsLambdaCh | read-only | mandatory | The Card port's Lambda channel |
| 1.3.6.1.4.1.6926.1.41.10 | NodefanUp | The SNMP trap that is generated when Fan unit changes it's state from notActive or fail to active | ||
| 1.3.6.1.4.1.6926.1.41.11 | NodefanDown | The SNMP trap that is generated when Fan unit changes it's state from active to notActive or fail | ||
| 1.3.6.1.4.1.6926.1.41.11 | NodeoaLdCardChannelInfo | |||
| 1.3.6.1.4.1.6926.1.41.11.2 | TableoaLdCardChannelCfgTable | not-accessible | mandatory | Table of Lambda Driver Card Channels configuration. |
| 1.3.6.1.4.1.6926.1.41.11.2.1 | RowoaLdCardChannelCfgEntry | not-accessible | mandatory | Lambda Driver Card Channels configuration Entry. |
| 1.3.6.1.4.1.6926.1.41.11.2.1.1 | ColumnoaLdCardChSlotId | read-only | mandatory | The slot#. An index from 1 to The number of slots. |
| 1.3.6.1.4.1.6926.1.41.11.2.1.2 | ColumnoaLdCardChGroupId | read-only | mandatory | . |
| 1.3.6.1.4.1.6926.1.41.11.2.1.3 | ColumnoaLdCardChChannelId | read-only | mandatory | . |
| 1.3.6.1.4.1.6926.1.41.11.2.1.4 | ColumnoaLdCardChOdu1Index | read-write | mandatory | For clients that mapped into the OTN payload. Indicates the index of the OPU-1 payload area. 0 - not supported, or client is not configured. 1 - Client mapped … |
| 1.3.6.1.4.1.6926.1.41.11.2.1.5 | ColumnoaLdCardChOdu1TsIndex | read-write | mandatory | For clients that mapped into the OTN payload. Indicates the tributary slot index among the 16 tributary slots, of the OPU-1 payload area. 0 - not supported, or… |
| 1.3.6.1.4.1.6926.1.41.11.2.1.6 | ColumnoaLdCardChOdu1TsSize | read-write | mandatory | For clients that mapped into the OTN payload. Indicates the number of tributary slots that are occupied by the client's rate. 0 - not supported, or client is n… |
| 1.3.6.1.4.1.6926.1.41.11.2.1.7 | ColumnoaLdCardChRate | read-write | mandatory | |
| 1.3.6.1.4.1.6926.1.41.12 | NodeoaLdOAmplifierInfo | |||
| 1.3.6.1.4.1.6926.1.41.12 | NodeswitchPrimary | The SNMP trap that is generated when optical switch on redundant card changes it's state from Secondary to Primary | ||
| 1.3.6.1.4.1.6926.1.41.12.2 | TableoaLdOAmplifierCardInfoTable | not-accessible | mandatory | Table of installed Lambda Driver Optical Amplifier Cards |
| 1.3.6.1.4.1.6926.1.41.12.2.1 | RowoaLdOAmplifierCardInfoEntry | not-accessible | mandatory | Installed Lambda Driver Optical Amplifier Cards |
| 1.3.6.1.4.1.6926.1.41.12.2.1.1 | ColumnoaLdOAmplifierCardSlotNumber | read-only | mandatory | The slot#. An index from 1 to The number of slots |
| 1.3.6.1.4.1.6926.1.41.12.2.1.2 | ColumnoaLdOAmplifierCardConfiguration | read-only | mandatory | The Optical Amplifier Configuration |
| 1.3.6.1.4.1.6926.1.41.12.2.1.3 | ColumnoaLdOAmplifierCardModuleType | read-only | mandatory | The Optical Amplifier Module Type |
| 1.3.6.1.4.1.6926.1.41.12.2.1.4 | ColumnoaLdOAmplifierCardHardwareVersion | read-only | mandatory | The Optical Amplifier Module Hardware Version |
| 1.3.6.1.4.1.6926.1.41.12.2.1.5 | ColumnoaLdOAmplifierCardSoftwareVersion | read-only | mandatory | The Optical Amplifier Module Software Version |
| 1.3.6.1.4.1.6926.1.41.12.2.1.6 | ColumnoaLdOAmplifierCardSerialNumber | read-only | mandatory | The Optical Amplifier Module Serial Number |
| 1.3.6.1.4.1.6926.1.41.12.2.1.7 | ColumnoaLdOAmplifierCardTemperature | read-only | mandatory | The Optical Amplifier Module Temperature (in units of 1/10 Degrees Celsius [0.1 C]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.8 | ColumnoaLdOAmplifierCardPSVoltage | read-only | mandatory | The Optical Amplifier Power Supply Voltage (in units of 1/100 Volts [0.01 V]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.9 | ColumnoaLdOAmplifierCardPump1Current | read-only | mandatory | The Optical Amplifier Pump 1 Current (in units of 1/10 milliamperes [0.1 mA]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.10 | ColumnoaLdOAmplifierCardPump1MaxCurrent | read-only | mandatory | The Optical Amplifier Pump 1 Maximum Current (in units of 1/10 milliamperes [0.1 mA]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.11 | ColumnoaLdOAmplifierCardPump2Current | read-only | mandatory | The Optical Amplifier Pump 2 Current (in units of 1/10 milliamperes [0.1 mA]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.12 | ColumnoaLdOAmplifierCardPump2MaxCurrent | read-only | mandatory | The Optical Amplifier Pump 2 Maximum Current (in units of 1/10 milliamperes [0.1 mA]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.13 | ColumnoaLdOAmplifierCardInputPower | read-only | mandatory | The Optical Amplifier Input Optical Power (in units of 1/100 [0.01 dBm]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.14 | ColumnoaLdOAmplifierCardOutputPower | read-only | mandatory | The Optical Amplifier Output Optical Power (in units of 1/100 [0.01 dBm]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.15 | ColumnoaLdOAmplifierCardModuleGain | read-only | mandatory | The Optical Amplifier Optical Module Gain (in units of 1/100 [0.01 dB]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.16 | ColumnoaLdOAmplifierCardPump1Power | read-only | mandatory | The Optical Amplifier Pump 1 Power (in units of 1/100 milliwatts [0.01 mW]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.17 | ColumnoaLdOAmplifierCardPump2Power | read-only | mandatory | The Optical Amplifier Pump 2 Power (in units of 1/100 milliwatts [0.01 mW]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.18 | ColumnoaLdOAmplifierCardMaximumPower | read-only | mandatory | The Optical Amplifier Optical Maximum Power (in units of 1/100 [0.01 dBm]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.19 | ColumnoaLdOAmplifierCardRatedGain | read-only | mandatory | The Optical Amplifier Optical Rated Gain (in units of 1/100 [0.01 dB]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.20 | ColumnoaLdOAmplifierCardAlarmStatus | read-only | mandatory | The Optical Amplifier Alarms. This object is organised as a bit map. Each bit represents an alarm. If the object is zero - no alarm is active. 0x0000 ('0000 00… |
| 1.3.6.1.4.1.6926.1.41.12.2.1.25 | ColumnoaLdOAmplifierCardAttributes | read-only | mandatory | The Optical Amplifier Attributes. This object is organised as a bit map. Each bit represents one existed attribute. 0x0000 ('0000 0000 0000 0000'B) - No additi… |
| 1.3.6.1.4.1.6926.1.41.12.2.1.30 | ColumnoaLdOAmplifierCardOperationMode | read-write | mandatory | The Optical Amplifier Operational Mode |
| 1.3.6.1.4.1.6926.1.41.12.2.1.31 | ColumnoaLdOAmplifierCardRunMode | read-write | mandatory | The Optical Amplifier Run Mode |
| 1.3.6.1.4.1.6926.1.41.12.2.1.32 | ColumnoaLdOAmplifierCardAutoShutdownState | read-write | mandatory | The Optical Amplifier Auto Shutdown Status |
| 1.3.6.1.4.1.6926.1.41.12.2.1.33 | ColumnoaLdOAmplifierCardInputThreshold | read-write | mandatory | The Optical Amplifier Input Threshold (in units of 1/100 [0.01 dBm]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.34 | ColumnoaLdOAmplifierCardOutputThreshold | read-write | mandatory | The Optical Amplifier Output Threshold (in units of 1/100 [0.01 dBm]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.35 | ColumnoaLdOAmplifierCardShutdownThreshold | read-write | mandatory | The Optical Amplifier Shutdown Threshold (in units of 1/100 [0.01 dBm]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.36 | ColumnoaLdOAmplifierCardLowTempThreshold | read-write | mandatory | The Optical Amplifier Low Temperature Threshold (in units of 1/10 Degrees Celsius [0.1 C]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.37 | ColumnoaLdOAmplifierCardHighTempThreshold | read-write | mandatory | The Optical Amplifier High Temperature Threshold (in units of 1/10 Degrees Celsius [0.1 C]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.38 | ColumnoaLdOAmplifierCardPump1CurrentSet | read-write | mandatory | The Optical Amplifier Pump 1 Current Setting (in units of 1/10 milliamperes [0.1 mA]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.39 | ColumnoaLdOAmplifierCardPump2CurrentSet | read-write | mandatory | The Optical Amplifier Pump 2 Current Setting (in units of 1/10 milliamperes [0.1 mA]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.40 | ColumnoaLdOAmplifierCardOutputPowerSet | read-write | mandatory | The Optical Amplifier Output Power Setting (in units of 1/100 [0.01 dBm]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.41 | ColumnoaLdOAmplifierCardGainSet | read-write | mandatory | The Optical Amplifier Gain Setting (in units of 1/100 [0.01 dB]). For Raman12 module (EM800-OAR12) Estimated Raman Gain. |
| 1.3.6.1.4.1.6926.1.41.12.2.1.42 | ColumnoaLdOAmplifierCardPumpOutputPower | read-only | mandatory | The C-Band Raman Amplifier Pump Output Power (in units of of 1/100 [0.01 dBm]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.43 | ColumnoaLdOAmplifierCardReflectedPower | read-only | mandatory | The C-Band Raman Amplifier Reflected Pump Power (in units of 1/100 [0.01 dBm]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.44 | ColumnoaLdOAmplifierCardBackReflRatio | read-only | mandatory | The Raman12 Back Reflection ratio between reflected and transmitted power (in units of 1/100 [0.01 dB]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.45 | ColumnoaLdOAmplifierCardBackReflThresh | read-only | mandatory | The Raman12 Back Reflection Threshold (in units of 1/100 [0.01 dBm]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.46 | ColumnoaLdOAmplifierCardAutoPowerReduction | read-only | mandatory | The Raman12 Auto Power Reduction (APR) Status in case of Back Reflection (BR) alarm. APR Enable means that the unit will mute its output power in case of BR al… |
| 1.3.6.1.4.1.6926.1.41.12.2.1.47 | ColumnoaLdOAmplifierCardOutputPumpPowerThresh | read-write | mandatory | The Raman12 Output pump power Alarm Threshold (in units of 1/100 milliwatts [0.01 mW]) |
| 1.3.6.1.4.1.6926.1.41.12.2.1.48 | ColumnoaLdOAmplifierCardCalibrationFactor | read-write | mandatory | The Raman12 calibration factor for Estimated Raman Gain. This coefficient is used to calculate the estimated Raman gain; default value = 0. |
| 1.3.6.1.4.1.6926.1.41.12.2.1.49 | ColumnoaLdOAmplifierCardTempAlarm | read-write | mandatory | The Raman12 Shutdown status in case of module temperature alarm. |
| 1.3.6.1.4.1.6926.1.41.12.2.1.50 | ColumnoaLdOAmplifierCardPump1Ratio | read-write | mandatory | The Raman12 pump 1 power ratio. Units: percent. |
| 1.3.6.1.4.1.6926.1.41.12.3 | TableoaLdOAmplifierPumpInfoTable | not-accessible | mandatory | Table of installed Lambda Driver C-Band Raman Amplifier Pumps |
| 1.3.6.1.4.1.6926.1.41.12.3.1 | RowoaLdOAmplifierPumpInfoEntry | not-accessible | mandatory | Installed Lambda Driver Optical Amplifier Pumps |
| 1.3.6.1.4.1.6926.1.41.12.3.1.2 | ColumnoaLdOAmplifierPumpNumber | read-only | mandatory | The pump#. An index from 1 to The number of pumps |
| 1.3.6.1.4.1.6926.1.41.12.3.1.3 | ColumnoaLdOAmplifierPumpCurrent | read-only | mandatory | The C-Band Raman Amplifier Pump Drive Current (in units of mA) |
| 1.3.6.1.4.1.6926.1.41.12.3.1.4 | ColumnoaLdOAmplifierPumpPower | read-only | mandatory | The C-Band Raman Amplifier Pump Output Power (in units of mW) |
| 1.3.6.1.4.1.6926.1.41.12.3.1.5 | ColumnoaLdOAmplifierPumpLaserTemp | read-only | mandatory | The C-Band Raman Amplifier Pump Laser Temperature (in units of 1/10 [0.1 deg C]) |
| 1.3.6.1.4.1.6926.1.41.12.10 | ScalaroaLdOAmplifierCompInterfaceCount | read-only | mandatory | The number of modules in the system which are Optical Amplifier compatible. |
| 1.3.6.1.4.1.6926.1.41.13 | NodeoaLdOcmCardInfo | |||
| 1.3.6.1.4.1.6926.1.41.13 | NodeswitchSecondary | The SNMP trap that is generated when optical switch on redundant card changes it's state from Primary to Secondary | ||
| 1.3.6.1.4.1.6926.1.41.13.2 | TableoaLdOcmCardPortsInfoTable | not-accessible | mandatory | Information table of installed OCM Cards |
| 1.3.6.1.4.1.6926.1.41.13.2.1 | RowoaLdOcmCardPortsInfoEntry | not-accessible | mandatory | Installed OCM Cards |
| 1.3.6.1.4.1.6926.1.41.13.2.1.1 | ColumnoaLdOcmCardPortsSlotNumber | read-only | mandatory | The slot#. An index from 1 to The number of slots |
| 1.3.6.1.4.1.6926.1.41.13.2.1.2 | ColumnoaLdOcmCardPortsPortNumber | read-only | mandatory | The port#. An index from 1 to The number of ports |
| 1.3.6.1.4.1.6926.1.41.13.2.1.3 | ColumnoaLdOcmCardPortsSectionLof | read-only | mandatory | Loss of Frame (LOF) indication. |
| 1.3.6.1.4.1.6926.1.41.13.2.1.4 | ColumnoaLdOcmCardPortsSectionLos | read-only | mandatory | Loss of Signal (LOS) indication. |
| 1.3.6.1.4.1.6926.1.41.13.2.1.5 | ColumnoaLdOcmCardPortsSectionLoc | read-only | mandatory | Loss of Clock (LOC) indication. |
| 1.3.6.1.4.1.6926.1.41.13.2.1.6 | ColumnoaLdOcmCardPortsSectionB1 | read-only | mandatory | B1 bytes monitoring for correct Bit Interleaved parity (BIP-8) values. BIP-8 is calculated over all bytes of each frame before descrambling. |
| 1.3.6.1.4.1.6926.1.41.13.2.1.7 | ColumnoaLdOcmCardPortsLineAis | read-only | mandatory | Line (AIS) - Alarm Indication Signal. |
| 1.3.6.1.4.1.6926.1.41.13.2.1.8 | ColumnoaLdOcmCardPortsLineRdi | read-only | mandatory | Line (RDI) - Remote Defect Indication. A returned signal to indicate upon LOS, LOF or AIS. |
| 1.3.6.1.4.1.6926.1.41.13.2.1.9 | ColumnoaLdOcmCardPortsLineB2 | read-only | mandatory | B2 bytes monitoring for correct Bit Interleaved parity (BIP-8) values. BIP-384 is calculated over all received data after descrambling. |
| 1.3.6.1.4.1.6926.1.41.13.2.1.10 | ColumnoaLdOcmCardPortsLineFebe | read-only | mandatory | Line FEBE (REI) - The number of B2 errors that were detected by the remote terminal in it's received signal. |
| 1.3.6.1.4.1.6926.1.41.13.2.1.11 | ColumnoaLdOcmCardPortsPathAis | read-only | mandatory | PATH (AIS) - PATH Alarm Indication Signal. |
| 1.3.6.1.4.1.6926.1.41.13.2.1.12 | ColumnoaLdOcmCardPortsPathLop | read-only | mandatory | PATH (LOP) - Loss Of Pointer. PATH indication of the pointer state. |
| 1.3.6.1.4.1.6926.1.41.13.2.1.13 | ColumnoaLdOcmCardPortsPathB3 | read-only | mandatory | B3 bytes monitoring for correct Bit Interleaved parity (BIP-8) values. |
| 1.3.6.1.4.1.6926.1.41.13.2.1.14 | ColumnoaLdOcmCardPortsPathPse | read-only | mandatory | This is an interperter justification counter that counts every positive justification. |
| 1.3.6.1.4.1.6926.1.41.13.2.1.15 | ColumnoaLdOcmCardPortsPathNse | read-only | mandatory | This is an interperter justification counter that counts every negative justification. |
| 1.3.6.1.4.1.6926.1.41.14 | NodeconfigChangeIn | The SNMP trap that is generated when a card is inserted into the chassis | ||
| 1.3.6.1.4.1.6926.1.41.15 | NodeoaLdRoadmInfo | |||
| 1.3.6.1.4.1.6926.1.41.15 | NodetransponderAccessRx | The SNMP trap that is generated when a transponder card changes it's Access receive indication. Note: this trap is send only if oaLdTrapsVer is not supported | ||
| 1.3.6.1.4.1.6926.1.41.15.2 | TableoaLdRoadmInfoTable | not-accessible | mandatory | Table of installed Lambda Driver ROADM Modules |
| 1.3.6.1.4.1.6926.1.41.15.2.1 | RowoaLdRoadmInfoEntry | not-accessible | mandatory | Installed Lambda Driver ROADM Modules |
| 1.3.6.1.4.1.6926.1.41.15.2.1.1 | ColumnoaLdRoadmSlotNumber | read-only | mandatory | The slot#. An index from 1 to The number of slots |
| 1.3.6.1.4.1.6926.1.41.15.2.1.2 | ColumnoaLdRoadmType | read-only | mandatory | The ROADM module type each module type gets a unique id number |
| 1.3.6.1.4.1.6926.1.41.15.2.1.3 | ColumnoaLdRoadmDescription | read-only | mandatory | The description of the ROADM module type |
| 1.3.6.1.4.1.6926.1.41.15.2.1.4 | ColumnoaLdRoadmSerialNumber | read-only | mandatory | The ROADM module serial number |
| 1.3.6.1.4.1.6926.1.41.15.2.1.5 | ColumnoaLdRoadmBoardVersion | read-only | mandatory | The ROADM module board version |
| 1.3.6.1.4.1.6926.1.41.15.2.1.6 | ColumnoaLdRoadmFpgaVersion | read-only | mandatory | The ROADM module FPGA version |
| 1.3.6.1.4.1.6926.1.41.15.2.1.7 | ColumnoaLdRoadmBootVersion | read-only | mandatory | The ROADM module Boot version |
| 1.3.6.1.4.1.6926.1.41.15.2.1.8 | ColumnoaLdRoadmMcVersion | read-only | mandatory | The ROADM module MicroController code version |
| 1.3.6.1.4.1.6926.1.41.15.2.1.9 | ColumnoaLdRoadmDate | read-only | mandatory | The ROADM module manufacture date |
| 1.3.6.1.4.1.6926.1.41.15.2.1.15 | ColumnoaLdRoadmStatus | read-only | mandatory | The ROADM module status |
| 1.3.6.1.4.1.6926.1.41.15.2.1.16 | ColumnoaLdRoadmComOutPortAdminStatus | read-write | mandatory | The ROADM COM Output port admin status 2 - Normal - all ports are configured as their oaLdRoadmPortAdminState; 3 - Disable - all ports are disabled. |
| 1.3.6.1.4.1.6926.1.41.15.2.1.17 | ColumnoaLdRoadmFail | read-only | mandatory | The ROADM module fail status 2 - Module works OK 3 - Module fail |
| 1.3.6.1.4.1.6926.1.41.15.2.1.18 | ColumnoaLdRoadmTemperature | read-only | mandatory | The ROADM module temperature or The WSS ROADM zone1 temperature. Units: 0.1 [C] |
| 1.3.6.1.4.1.6926.1.41.15.2.1.19 | ColumnoaLdRoadmHeaterMode | read-only | mandatory | The ROADM module AWG heater enable mode 2 - AWG Heater On 3 - AWG Heater Off |
| 1.3.6.1.4.1.6926.1.41.15.2.1.20 | ColumnoaLdRoadmHeaterTemperature | read-only | mandatory | The ROADM module AWG heater temperature Units: 0.1 [C] |
| 1.3.6.1.4.1.6926.1.41.15.2.1.21 | ColumnoaLdRoadmSpacing | read-write | mandatory | The ROADM module channel spacing |
| 1.3.6.1.4.1.6926.1.41.15.2.1.22 | ColumnoaLdRoadmNumberOfChPorts | read-only | mandatory | Number of channel ports at ROADM card. |
| 1.3.6.1.4.1.6926.1.41.15.2.1.23 | ColumnoaLdRoadmPowerEqualization | read-write | mandatory | Makes procedure of automatic Power Equalization. |
| 1.3.6.1.4.1.6926.1.41.15.2.1.24 | ColumnoaLdRoadmZone2Temperature | read-only | mandatory | The WSS ROADM zone2 temperature Units: 0.1 [C] |
| 1.3.6.1.4.1.6926.1.41.15.2.1.25 | ColumnoaLdRoadmZone3Temperature | read-only | mandatory | The WSS ROADM zone3 temperature Units: 0.1 [C] |
| 1.3.6.1.4.1.6926.1.41.15.2.1.26 | ColumnoaLdRoadmNumberOfChannels | read-only | mandatory | Number of channels at ROADM card. |
| 1.3.6.1.4.1.6926.1.41.15.2.1.27 | ColumnoaLdRoadmReconfigureSwitch | read-write | mandatory | Makes procedure of implementing switch configuration on hardware. |
| 1.3.6.1.4.1.6926.1.41.15.2.1.28 | ColumnoaLdRoadmFirstChannel | read-only | mandatory | The value of the First Lambda Channel Number in the interval of possible Lambda Channels Numbers. For the WSS ROADM Modules the value is equal to Lambda Channe… |
| 1.3.6.1.4.1.6926.1.41.15.2.1.29 | ColumnoaLdRoadmLastChannel | read-only | mandatory | The value of the Last Lambda Channel Number in the interval of possible Lambda Channels Numbers. For the WSS ROADM Modules the value is equal to Lambda Channel… |
| 1.3.6.1.4.1.6926.1.41.15.2.1.30 | ColumnoaLdRoadmDefaultConfiguration | read-write | mandatory | Restore default Port Channel Configuration for Module. Setting 'restoreDefault' for Modules EM1600-WSS2Q and EM1600-WSS4D will block all Channels configured on… |
| 1.3.6.1.4.1.6926.1.41.15.2.1.31 | ColumnoaLdRoadmPowerBalancingMode | read-write | mandatory | ROADM Module power balancing mode. |
| 1.3.6.1.4.1.6926.1.41.15.3 | TableoaLdRoadmMonitorTable | not-accessible | mandatory | Table of installed Lambda Driver ROADM Modules Monitoring |
| 1.3.6.1.4.1.6926.1.41.15.3.1 | RowoaLdRoadmMonitorEntry | not-accessible | mandatory | Installed Lambda Driver ROADM Modules Monitoring |
| 1.3.6.1.4.1.6926.1.41.15.3.1.1 | ColumnoaLdRoadmMonitorSlotNumber | read-only | mandatory | The slot#. An index from 1 to The number of slots |
| 1.3.6.1.4.1.6926.1.41.15.3.1.2 | ColumnoaLdRoadmMonitorComInputPower | read-only | mandatory | The ROADM module COM IN power Units: 0.1 [dBm] |
| 1.3.6.1.4.1.6926.1.41.15.3.1.3 | ColumnoaLdRoadmMonitorComOutputPower | read-only | mandatory | The ROADM module COM OUT power Units: 0.1 [dBm] |
| 1.3.6.1.4.1.6926.1.41.15.3.1.4 | ColumnoaLdRoadmMonitorExpInputPower | read-only | mandatory | The ROADM module Input power (EXP IN) Units: 0.1 [dBm] |
| 1.3.6.1.4.1.6926.1.41.15.3.1.5 | ColumnoaLdRoadmMonitorExpOutputPower | read-only | mandatory | The ROADM module EXP OUT power Units: 0.1 [dBm] |
| 1.3.6.1.4.1.6926.1.41.15.3.1.6 | ColumnoaLdRoadmMonitorDropOutputPower | read-only | mandatory | The ROADM module DROP OUT power Units: 0.1 [dBm] |
| 1.3.6.1.4.1.6926.1.41.15.4 | TableoaLdRoadmChannelTable | not-accessible | mandatory | Table of installed Lambda Driver ROADM Modules Ports |
| 1.3.6.1.4.1.6926.1.41.15.4.1 | RowoaLdRoadmChannelEntry | not-accessible | mandatory | Installed Lambda Driver ROADM Modules Channels |
| 1.3.6.1.4.1.6926.1.41.15.4.1.1 | ColumnoaLdRoadmChannelSlotNumber | read-only | mandatory | The slot#. An index from 1 to The number of slots |
| 1.3.6.1.4.1.6926.1.41.15.4.1.2 | ColumnoaLdRoadmChannelLambdaChannel | read-only | mandatory | The ROADM module Channel Lambda Channel Number multiplied by 1000. Example: channel 20 will apear as 20000. |
| 1.3.6.1.4.1.6926.1.41.15.4.1.3 | ColumnoaLdRoadmChannelPortNumber | read-only | mandatory | The port#. An index from 1 to The number of ports. |
| 1.3.6.1.4.1.6926.1.41.15.4.1.4 | ColumnoaLdRoadmChannelWavelength | read-only | mandatory | The ROADM module Port Channel Wavelenth, Units: 0.01 Nano Meter[nm] |
| 1.3.6.1.4.1.6926.1.41.15.4.1.5 | ColumnoaLdRoadmChannelDropPortNumber | read-write | mandatory | The number of Drop Port, connected to this Channel. |
| 1.3.6.1.4.1.6926.1.41.15.4.1.6 | ColumnoaLdRoadmChannelDropAttenuation | read-write | mandatory | The ROADM module port VOA Drop Attenuation, integer from 0 till 150, Units: 0.1 [dB] |
| 1.3.6.1.4.1.6926.1.41.15.4.1.7 | ColumnoaLdRoadmChannelConfigStatus | read-only | mandatory | The status of ROADM module Channel. Set 'virtual' if configuration didn't save in HW. |
| 1.3.6.1.4.1.6926.1.41.15.4.1.8 | ColumnoaLdRoadmChannelPower1 | read-only | mandatory | The ROADM module Channel Power, (Drop Peak Power for module EM1600-WSS9, Com Output West or East Total Power for module EM1600-WSS2Q, Com Output Total Power fo… |
| 1.3.6.1.4.1.6926.1.41.15.4.1.9 | ColumnoaLdRoadmChannelPower2 | read-only | mandatory | The ROADM module Channel Power, (Add Peak Power for module EM1600-WSS9, Not applicable object for module EM1600-WSS2Q, Com Input Total Power for module EM1600-… |
| 1.3.6.1.4.1.6926.1.41.15.4.1.10 | ColumnoaLdRoadmChannelDropPeakFrequency | read-only | mandatory | The ROADM module Channel Frequency, (Drop Peak Frequency) Units: 0.0001 [THz] |
| 1.3.6.1.4.1.6926.1.41.15.4.1.11 | ColumnoaLdRoadmChannelAddPeakFrequency | read-only | mandatory | The ROADM module Channel Frequency, (Add Peak Frequency) Units: 0.0001 [THz] |
| 1.3.6.1.4.1.6926.1.41.15.4.1.12 | ColumnoaLdRoadmChannelAddAttenuation | read-write | mandatory | The ROADM module port VOA Add Attenuation, integer from 0 till 250, Units: 0.1 [dB] |
| 1.3.6.1.4.1.6926.1.41.15.4.1.13 | ColumnoaLdRoadmChannelGridFrequency | read-only | mandatory | The ROADM module Channel Grid Frequency Units: 0.0001 [THz] |
| 1.3.6.1.4.1.6926.1.41.15.4.1.14 | ColumnoaLdRoadmChannelSpacing | read-only | mandatory | The ROADM Channel Spacing |
| 1.3.6.1.4.1.6926.1.41.15.5 | TableoaLdRoadmThresholdTable | not-accessible | mandatory | Table of installed Lambda Driver ROADM Modules Thresholds |
| 1.3.6.1.4.1.6926.1.41.15.5.1 | RowoaLdRoadmThresholdEntry | not-accessible | mandatory | Installed Lambda Driver ROADM Modules Thresholds |
| 1.3.6.1.4.1.6926.1.41.15.5.1.1 | ColumnoaLdRoadmThresholdSlotNumber | read-only | mandatory | The slot#. An index from 1 to The number of slots |
| 1.3.6.1.4.1.6926.1.41.15.5.1.2 | ColumnoaLdRoadmThresholdIndex | read-only | mandatory | The threshold index An index from 1 to The number of thresholds |
| 1.3.6.1.4.1.6926.1.41.15.5.1.3 | ColumnoaLdRoadmThresholdAwgTemp | read-only | mandatory | The ROADM module AWG temperature threshold Units: 0.1 [C] |
| 1.3.6.1.4.1.6926.1.41.15.5.1.4 | ColumnoaLdRoadmThresholdTemp | read-only | mandatory | The ROADM module temperature threshold Units: 0.1 [C] |
| 1.3.6.1.4.1.6926.1.41.15.5.1.5 | ColumnoaLdRoadmThresholdComInputPwr | read-only | mandatory | The ROADM module COM IN power threshold (demultiplexer channel output) Units: 0.1 [dBm] |
| 1.3.6.1.4.1.6926.1.41.15.5.1.6 | ColumnoaLdRoadmThresholdComOutputPwr | read-only | mandatory | The ROADM module COM OUT power threshold Units: 0.1 [dBm] |
| 1.3.6.1.4.1.6926.1.41.15.5.1.7 | ColumnoaLdRoadmThresholdExpInputPwr | read-only | mandatory | The ROADM module input power (EXT IN) threshold Units: 0.1 [dBm] |
| 1.3.6.1.4.1.6926.1.41.15.5.1.8 | ColumnoaLdRoadmThresholdExpOutputPwr | read-only | mandatory | The ROADM module EXP OUT power threshold Units: 0.1 [dBm] |
| 1.3.6.1.4.1.6926.1.41.15.5.1.9 | ColumnoaLdRoadmThresholdDropOutputPwr | read-only | mandatory | The ROADM module DROP OUT power threshold Units: 0.1 [dBm] |
| 1.3.6.1.4.1.6926.1.41.15.6 | TableoaLdRoadmPortInfoTable | not-accessible | mandatory | Table of installed Lambda Driver ROADM Modules Ports |
| 1.3.6.1.4.1.6926.1.41.15.6.1 | RowoaLdRoadmPortInfoEntry | not-accessible | mandatory | Installed Lambda Driver ROADM Modules Ports |
| 1.3.6.1.4.1.6926.1.41.15.6.1.1 | ColumnoaLdRoadmPortSlotNumber | read-only | mandatory | The slot#. An index from 1 to The number of slots |
| 1.3.6.1.4.1.6926.1.41.15.6.1.2 | ColumnoaLdRoadmPortPortNumber | read-only | mandatory | The port#. An index from 1 to The number of ports (channels) |
| 1.3.6.1.4.1.6926.1.41.15.6.1.3 | ColumnoaLdRoadmPortAdminState | read-write | mandatory | The ROADM module administration state of the Port, Add, Pass through or Dark. Setting 'dark' for Modules EM1600-WSS2Q and EM1600-WSS4D will block all Channels … |
| 1.3.6.1.4.1.6926.1.41.15.6.1.4 | ColumnoaLdRoadmPortServiceState | read-only | mandatory | The ROADM module switch setting of the port, Add, Pass through or Dark |
| 1.3.6.1.4.1.6926.1.41.15.6.1.5 | ColumnoaLdRoadmPortPower | read-only | mandatory | The ROADM module port input power (Multiplexer Input Power for module EM1600-ROADM40, Com Input Total Power for module EM1600-WSS4D). Units: 0.1 [dBm] |
| 1.3.6.1.4.1.6926.1.41.15.6.1.7 | ColumnoaLdRoadmPortVoaAttenuationAdd | read-write | mandatory | The ROADM module port VOA add attenuation, integer from 0 till 250, Units: 0.1 [dB] |
| 1.3.6.1.4.1.6926.1.41.15.6.1.8 | ColumnoaLdRoadmPortVoaAttenuationPass | read-write | mandatory | The ROADM module port VOA pass attenuation, integer from 0 till 250, Units: 0.1 [dB] |
| 1.3.6.1.4.1.6926.1.41.15.6.1.9 | ColumnoaLdRoadmPortVoaAttenuationDrop | read-write | mandatory | The ROADM module port VOA drop attenuation, integer from 0 till 250, Units: 0.1 [dB] |
| 1.3.6.1.4.1.6926.1.41.15.6.1.10 | ColumnoaLdRoadmPortChannelWavelength | read-write | mandatory | The ROADM module port channel wavelenth, Units: 0.01 Nano Meter[nm] |
| 1.3.6.1.4.1.6926.1.41.15.6.1.11 | ColumnoaLdRoadmPortLambdaChannel | read-only | mandatory | The ROADM module port lambda channel number multiplied by 1000. Example: channel 20 will apear as 20000. |
| 1.3.6.1.4.1.6926.1.41.15.6.1.12 | ColumnoaLdRoadmPortVoaMinAttenuation | read-write | mandatory | The module port VOA minimum attenuation value, integer in Units: 0.1 [dB] |
| 1.3.6.1.4.1.6926.1.41.15.6.1.13 | ColumnoaLdRoadmPortVoaMaxAttenuation | read-write | mandatory | The module port VOA maximum attenuation value, integer in Units: 0.1 [dB] |
| 1.3.6.1.4.1.6926.1.41.15.6.1.14 | ColumnoaLdRoadmPortName | read-only | mandatory | Port Name string (as: Add-Drop West, ExpIn-ExpOut East, Com Out, WB1 In-Out etc.) |
| 1.3.6.1.4.1.6926.1.41.15.6.1.15 | ColumnoaLdRoadmPortPowerSupported | read-only | mandatory | Optical Power value exists for this port. |
| 1.3.6.1.4.1.6926.1.41.15.6.1.16 | ColumnoaLdRoadmPortTotalPower | read-only | mandatory | The ROADM module Port Total Power value. Units: 0.1 [dBm] |
| 1.3.6.1.4.1.6926.1.41.15.6.1.17 | ColumnoaLdRoadmPortChanList | read-only | mandatory | List of Lambda Channels detected in the Port. Number of bytes in the Octet String is equal to the value of [oaLdRoadmNumberOfChannels]. Each Byte in the Octet … |
| 1.3.6.1.4.1.6926.1.41.15.6.1.18 | ColumnoaLdRoadmPortChanSrcPortList | read-only | mandatory | List of Input Port Numbers which Lambda Channels were detected in the Port. Number of bytes in the Octet String is equal to the value of [oaLdRoadmNumberOfChan… |
| 1.3.6.1.4.1.6926.1.41.15.6.1.19 | ColumnoaLdRoadmPortBalancingAdminStatus | read-write | mandatory | The ROADM module's port power balancing administrative status. |
| 1.3.6.1.4.1.6926.1.41.15.6.1.20 | ColumnoaLdRoadmPortBalancingOperStatus | read-only | mandatory | The ROADM module's port power balancing operative status. |
| 1.3.6.1.4.1.6926.1.41.15.6.1.21 | ColumnoaLdRoadmPortBalancingPower | read-write | mandatory | The ROADM module's port maximum COM OUT power. Units: 0.1 [dBm] |
| 1.3.6.1.4.1.6926.1.41.15.6.1.22 | ColumnoaLdRoadmPortBalancingMaxChnlsNum | read-write | mandatory | The ROADM module's port maximum channels number for power balancing. |
| 1.3.6.1.4.1.6926.1.41.15.6.1.23 | ColumnoaLdRoadmPortBalancingPowerPerChnl | read-only | mandatory | The ROADM module's calculated maximum output power per channel. Units: 0.1 [dBm] |
| 1.3.6.1.4.1.6926.1.41.15.7 | TableoaLdRoadmPortThresholdTable | not-accessible | mandatory | Table of installed Lambda Driver ROADM Modules Ports Threshold |
| 1.3.6.1.4.1.6926.1.41.15.7.1 | RowoaLdRoadmPortThresholdEntry | not-accessible | mandatory | Installed Lambda Driver ROADM Modules Ports Threshold |
| 1.3.6.1.4.1.6926.1.41.15.7.1.1 | ColumnoaLdRoadmPortThresholdSlotIndex | read-only | mandatory | The slot#. An index from 1 to The number of slots |
| 1.3.6.1.4.1.6926.1.41.15.7.1.2 | ColumnoaLdRoadmPortThresholdPortIndex | read-only | mandatory | The port#. An index from 1 to The number of ports (channels) |
| 1.3.6.1.4.1.6926.1.41.15.7.1.3 | ColumnoaLdRoadmPortThresholdIndex | read-only | mandatory | The threshold index An index from 1 to The number of thresholds |
| 1.3.6.1.4.1.6926.1.41.15.7.1.4 | ColumnoaLdRoadmPortThresholdPwr | read-only | mandatory | The ROADM module port power threshold, (multiplexer input power) Units: 0.1 [dBm] |
| 1.3.6.1.4.1.6926.1.41.16 | NodeoaLdPortsCrossConnect | |||
| 1.3.6.1.4.1.6926.1.41.16.1 | TableoaLdPortsCrossConnectTable | not-accessible | mandatory | Table of installed Cross Connect Ports |
| 1.3.6.1.4.1.6926.1.41.16.1.1 | RowoaLdPortsCrossConnectEntry | not-accessible | mandatory | Installed Cross Connect Ports |
| 1.3.6.1.4.1.6926.1.41.16.1.1.1 | ColumnoaLdPortsCrossConnectSlotNumber | read-only | mandatory | The Cross Connect module slot number. |
| 1.3.6.1.4.1.6926.1.41.16.1.1.2 | ColumnoaLdPortsCrossConnectPortNumber | read-only | mandatory | The port# from Cross Connect module. |
| 1.3.6.1.4.1.6926.1.41.16.1.1.3 | ColumnoaLdPortsCrossConnectNumber | read-write | mandatory | Number of port which is defined as connected with this port. The number is 0, if this port doesn't connected |
| 1.3.6.1.4.1.6926.1.41.16.1.1.4 | ColumnoaLdPortsCrossConnectAction | read-write | mandatory | Action to connect or disconnect this port with number. Get always returns other. For set have to be together with object oaLdPortsCrossConnectNumber. |
| 1.3.6.1.4.1.6926.1.41.17 | NodeoaLdOpticalMonitor | |||
| 1.3.6.1.4.1.6926.1.41.17 | NodetransponderWdmRx | The SNMP trap that is generated when a transponder card changes it's WDM receive indication. Note: this trap is send only if oaLdTrapsVer is not supported | ||
| 1.3.6.1.4.1.6926.1.41.17.1 | TableoaLdMeasurmentPointsTable | not-accessible | mandatory | Table of optical peaks and Spectral points numbers. |
| 1.3.6.1.4.1.6926.1.41.17.1.1 | RowoaLdMeasurmentPointsEntry | not-accessible | mandatory | Table of optical peaks and Spectral points numbers. |
| 1.3.6.1.4.1.6926.1.41.17.1.1.1 | ColumnoaLdMeasurmentPointsSlotNumber | read-only | mandatory | The slot#. An index from 1 to The number of slots |
| 1.3.6.1.4.1.6926.1.41.17.1.1.2 | ColumnoaLdMeasurmentPointsPortNumber | read-only | mandatory | The port#. An index from 1 to The number of ports. |
| 1.3.6.1.4.1.6926.1.41.17.1.1.3 | ColumnoaLdPeaksNumber | read-only | mandatory | The number of detected optical peaks. |
| 1.3.6.1.4.1.6926.1.41.17.1.1.4 | ColumnoaLdTotalBandPower | read-only | mandatory | The total band power. Units: 0.1 [dBm] |
| 1.3.6.1.4.1.6926.1.41.17.2 | TableoaLdPeaksMonitorTable | not-accessible | mandatory | Table of Spectral optical Peaks Monitoring. |
| 1.3.6.1.4.1.6926.1.41.17.2.1 | RowoaLdPeaksMonitorEntry | not-accessible | mandatory | Spectral optical Peaks Monitoring |
| 1.3.6.1.4.1.6926.1.41.17.2.1.1 | ColumnoaLdPeaksMonitorSlotNumber | read-only | mandatory | The slot#. An index from 1 to The number of slots |
| 1.3.6.1.4.1.6926.1.41.17.2.1.2 | ColumnoaLdPeaksMonitorPortNumber | read-only | mandatory | The port#. An index from 1 to The number of ports. |
| 1.3.6.1.4.1.6926.1.41.17.2.1.3 | ColumnoaLdPeaksMonitorPeakNumber | read-only | mandatory | The spectral peak#. An index from 1 to The number of measured spectral peaks. |
| 1.3.6.1.4.1.6926.1.41.17.2.1.4 | ColumnoaLdPeaksMonitorPeakFreq | read-only | mandatory | The peak frequency. Units: 0.0001 [THz]. |
| 1.3.6.1.4.1.6926.1.41.17.2.1.5 | ColumnoaLdPeaksMonitorPeakWavelength | read-only | mandatory | The peak wavelength. Units: 0.01 [nm]. |
| 1.3.6.1.4.1.6926.1.41.17.2.1.6 | ColumnoaLdPeaksMonitorPeakPower | read-only | mandatory | The peak power. Units: 0.1 [dBm] |
| 1.3.6.1.4.1.6926.1.41.17.2.1.7 | ColumnoaLdPeaksMonitorTotalPower | read-only | mandatory | The total power. Units: 0.1 [dBm] |
| 1.3.6.1.4.1.6926.1.41.17.2.1.8 | ColumnoaLdPeaksMonitorOsnr | read-only | mandatory | The peak OSNR. Units: 0.1 [dB] |
| 1.3.6.1.4.1.6926.1.41.17.2.1.9 | ColumnoaLdPeaksMonitorLeftValleyFreq | read-only | mandatory | The peak Left valley Frequency. Units: 0.0001 [THz]. |
| 1.3.6.1.4.1.6926.1.41.17.2.1.10 | ColumnoaLdPeaksMonitorLeftValleyPower | read-only | mandatory | The peak Left valley Power. Units: 0.1 [dBm]. |
| 1.3.6.1.4.1.6926.1.41.17.2.1.11 | ColumnoaLdPeaksMonitorRightValleyFreq | read-only | mandatory | The peak Right valley Frequency. Units: 0.0001 [THz]. |
| 1.3.6.1.4.1.6926.1.41.17.2.1.12 | ColumnoaLdPeaksMonitorRightValleyPower | read-only | mandatory | The peak Right valley Power. Units: 0.1 [dBm]. |
| 1.3.6.1.4.1.6926.1.41.18 | NodeoaLdDcmCardAttributes | |||
| 1.3.6.1.4.1.6926.1.41.18.1 | TableoaLdDcmCardPortsTable | not-accessible | mandatory | Table of installed DCM Cards |
| 1.3.6.1.4.1.6926.1.41.18.1.1 | RowoaLdDcmCardPortsEntry | not-accessible | mandatory | Installed DCM Cards |
| 1.3.6.1.4.1.6926.1.41.18.1.1.1 | ColumnoaLdDcmCardPortsSlotNumber | read-only | mandatory | The slot#. An index from 1 to The number of DCM slots |
| 1.3.6.1.4.1.6926.1.41.18.1.1.2 | ColumnoaLdDcmCardPortsPortNumber | read-only | mandatory | The port#. An index from 1 to The number of ports |
| 1.3.6.1.4.1.6926.1.41.18.1.1.3 | ColumnoaLdDcmCardPortsDistance | read-only | mandatory | DCM module distance. Units: km |
| 1.3.6.1.4.1.6926.1.41.18.1.1.4 | ColumnoaLdDcmCardPortsSpacing | read-only | mandatory | DCM module spacing. Units: GHz |
| 1.3.6.1.4.1.6926.1.41.18.1.1.5 | ColumnoaLdDcmCardPortsRate | read-only | mandatory | DCM module rate. Units: Giga |
| 1.3.6.1.4.1.6926.1.41.19 | NodeconfigChangeOut | The SNMP trap that is generated when a card is taken out of the chassis | ||
| 1.3.6.1.4.1.6926.1.41.20 | NodetransponderCardLoopBack | The SNMP trap that is generated when a transponder card changes it's LoopBack state. Note: this trap is send only if oaLdTrapsVer is not supported | ||
| 1.3.6.1.4.1.6926.1.41.21 | NoderedundantCardPrimaryRx | The SNMP trap that is generated when on redundant card the Primary fiber Receive status is changed | ||
| 1.3.6.1.4.1.6926.1.41.22 | NoderedundantCardSecondaryRx | The SNMP trap that is generated when on redundant card the Secondary fiber Receive status is changed | ||
| 1.3.6.1.4.1.6926.1.41.23 | NodecardPortsLink | The SNMP trap that is generated when the link status of a port at the card is changed. Note: this trap is send only if oaLdTrapsVer is not supported | ||
| 1.3.6.1.4.1.6926.1.41.25 | NodetransponderEntityAccessRx | The SNMP trap that is generated when a transponder at a card changes it's Access receive indication. Note: this trap is send only if oaLdTrapsVer is not suppor… | ||
| 1.3.6.1.4.1.6926.1.41.27 | NodetransponderEntityWdmRx | The SNMP trap that is generated when a transponder at a card changes it's WDM receive indication. Note: this trap is send only if oaLdTrapsVer is not supported | ||
| 1.3.6.1.4.1.6926.1.41.28 | NodetransponderEntityLoopBack | The SNMP trap that is generated when a transponder entity changes it's LoopBack state. Note: this trap is send only if oaLdTrapsVer is not supported | ||
| 1.3.6.1.4.1.6926.1.41.29 | NodetransponderCardPortsLoopBack | The SNMP trap that is generated when a transponder port changes it's LoopBack state. Note: this trap is send only if oaLdTrapsVer is not supported | ||
| 1.3.6.1.4.1.6926.1.41.30 | NodetransponderAccessRxOn | The SNMP trap that is generated when a transponder card changes it's Access receive indication to ON | ||
| 1.3.6.1.4.1.6926.1.41.31 | NodetransponderAccessRxOff | The SNMP trap that is generated when a transponder card changes it's Access receive indication to Off | ||
| 1.3.6.1.4.1.6926.1.41.32 | NodetransponderWdmRxOn | The SNMP trap that is generated when a transponder card changes it's WDM receive indication to On | ||
| 1.3.6.1.4.1.6926.1.41.33 | NodetransponderWdmRxOff | The SNMP trap that is generated when a transponder card changes it's WDM receive indication to Off | ||
| 1.3.6.1.4.1.6926.1.41.34 | NodetransponderCardLoopBackLoop | The SNMP trap that is generated when a transponder card changes it's LoopBack state to loop | ||
| 1.3.6.1.4.1.6926.1.41.35 | NodetransponderCardLoopBackNormal | The SNMP trap that is generated when a transponder card changes it's LoopBack state to normal | ||
| 1.3.6.1.4.1.6926.1.41.36 | NodecardPortsLinkOn | The SNMP trap that is generated when the link status of a port at the card is changed to On | ||
| 1.3.6.1.4.1.6926.1.41.37 | NodecardPortsLinkOff | The SNMP trap that is generated when the link status of a port at the card is changed to Off | ||
| 1.3.6.1.4.1.6926.1.41.38 | NodetransponderEntityAccessRxOn | The SNMP trap that is generated when a transponder at a card changes it's Access receive indication to On | ||
| 1.3.6.1.4.1.6926.1.41.39 | NodetransponderEntityAccessRxOff | The SNMP trap that is generated when a transponder at a card changes it's Access receive indication to Off | ||
| 1.3.6.1.4.1.6926.1.41.40 | NodetransponderEntityWdmRxOn | The SNMP trap that is generated when a transponder at a card changes it's WDM receive indication to On | ||
| 1.3.6.1.4.1.6926.1.41.41 | NodetransponderEntityWdmRxOff | The SNMP trap that is generated when a transponder at a card changes it's WDM receive indication to Off | ||
| 1.3.6.1.4.1.6926.1.41.42 | NodetransponderEntityLoopBackLoop | The SNMP trap that is generated when a transponder entity changes it's LoopBack state to loop | ||
| 1.3.6.1.4.1.6926.1.41.43 | NodetransponderEntityLoopBackNormal | The SNMP trap that is generated when a transponder entity changes it's LoopBack state to normal | ||
| 1.3.6.1.4.1.6926.1.41.44 | NodetransponderCardPortsLoopBackLoop | The SNMP trap that is generated when a transponder port changes it's LoopBack state to loop | ||
| 1.3.6.1.4.1.6926.1.41.45 | NodetransponderCardPortsLoopBackNormal | The SNMP trap that is generated when a transponder port changes it's LoopBack state to normal | ||
| 1.3.6.1.4.1.6926.1.41.46 | NoderedCardPositionPrimary | The SNMP trap that is generated when optical switch on redundant card changes it's state from Secondary to Primary | ||
| 1.3.6.1.4.1.6926.1.41.47 | NoderedCardPositionSecondary | The SNMP trap that is generated when optical switch on redundant card changes it's state from Primary to Secondary | ||
| 1.3.6.1.4.1.6926.1.41.48 | NodeoaLdCardTemperatureNormal | The SNMP trap that is generated when Temperature of the card placed in the corresponding slot returned to Normal. | ||
| 1.3.6.1.4.1.6926.1.41.49 | NodeoaLdCardTemperatureHigh | The SNMP trap that is generated when Temperature of the card placed in the corresponding slot became too High. | ||
| 1.3.6.1.4.1.6926.1.41.50 | NodeoaLdOAmplifierInputAlarmOn | The SNMP trap that is generated when an Optical Amplifier Input Power exceeds its threshold value. | ||
| 1.3.6.1.4.1.6926.1.41.51 | NodeoaLdOAmplifierInputAlarmOff | The SNMP trap that is generated when an Optical Amplifier Input Power returns below its threshold value. | ||
| 1.3.6.1.4.1.6926.1.41.52 | NodeoaLdOAmplifierOutputAlarmOn | The SNMP trap that is generated when an Optical Amplifier Output Power exceeds its threshold value. | ||
| 1.3.6.1.4.1.6926.1.41.53 | NodeoaLdOAmplifierOutputAlarmOff | The SNMP trap that is generated when an Optical Amplifier Output Power returns below its threshold value. | ||
| 1.3.6.1.4.1.6926.1.41.54 | NodeoaLdOAmplifierModuleTempAlarmOn | The SNMP trap that is generated when an Optical Amplifier Module Temperature exceeds its threshold value. | ||
| 1.3.6.1.4.1.6926.1.41.55 | NodeoaLdOAmplifierModuleTempAlarmOff | The SNMP trap that is generated when an Optical Amplifier Module Temperature returns below its threshold value. | ||
| 1.3.6.1.4.1.6926.1.41.56 | NodeoaLdOAmplifierInput2AlarmOn | The SNMP trap that is generated when an Optical Amplifier Input2 Power exceeds its threshold value. | ||
| 1.3.6.1.4.1.6926.1.41.57 | NodeoaLdOAmplifierInput2AlarmOff | The SNMP trap that is generated when an Optical Amplifier Input2 Power returns below its threshold value. | ||
| 1.3.6.1.4.1.6926.1.41.58 | NodeoaLdOAmplifierPSAlarmOn | The SNMP trap that is generated when an Optical Amplifier PS Voltage Current exceeds its threshold value. | ||
| 1.3.6.1.4.1.6926.1.41.59 | NodeoaLdOAmplifierPSAlarmOff | The SNMP trap that is generated when an Optical Amplifier PS Voltage Current returns below its threshold value. | ||
| 1.3.6.1.4.1.6926.1.41.60 | NodeoaLdOAmplifierAutoShutdownAlarmOn | The SNMP trap that is generated when an Optical Amplifier Auto Shutdown exceeds its threshold value. | ||
| 1.3.6.1.4.1.6926.1.41.61 | NodeoaLdOAmplifierAutoShutdownAlarmOff | The SNMP trap that is generated when an Optical Amplifier Auto Shutdown returns below its threshold value. | ||
| 1.3.6.1.4.1.6926.1.41.62 | NodeoaLdOAmplifierPumpTempAlarmOn | The SNMP trap that is generated when an Optical Amplifier Pump Temperature exceeds its threshold value. | ||
| 1.3.6.1.4.1.6926.1.41.63 | NodeoaLdOAmplifierPumpTempAlarmOff | The SNMP trap that is generated when an Optical Amplifier Pump Temperature returns below its threshold value. | ||
| 1.3.6.1.4.1.6926.1.41.64 | NodeoaLdOAmplifierPumpDriveCurrentAlarmOn | The SNMP trap that is generated when an Optical Amplifier Pump Drive Current exceeds its threshold value. | ||
| 1.3.6.1.4.1.6926.1.41.65 | NodeoaLdOAmplifierPumpDriveCurrentAlarmOff | The SNMP trap that is generated when an Optical Amplifier Pump Drive Current returns below its threshold value. | ||
| 1.3.6.1.4.1.6926.1.41.66 | NodeoaLdRamanAmplifierReflectedAlarmOn | The SNMP trap that is generated when an Optical Raman Amplifier Reflected Power exceeds its threshold value. | ||
| 1.3.6.1.4.1.6926.1.41.67 | NodeoaLdRamanAmplifierReflectedAlarmOff | The SNMP trap that is generated when an Optical Raman Amplifier Reflected Power returns below its threshold value. | ||
| 1.3.6.1.4.1.6926.1.41.94 | NodeoaLdDevCPUForceSwitchoverCommandInvoked | The SNMP trap that is generated when the command 'CPU Force Switchover is invoked. | ||
| 1.3.6.1.4.1.6926.1.41.95 | NodeoaLdFiberPrbsTestError | The SNMP trap that is generated when error is occurred during Fiber PRBS emulation test. | ||
| 1.3.6.1.4.1.6926.1.41.96 | NodeoaLdEMPortDryContactClosed | The SNMP trap that is generated when the Dry Contact of E&M port is closed. | ||
| 1.3.6.1.4.1.6926.1.41.97 | NodeoaLdEMPortDryContactOpened | The SNMP trap that is generated when the Dry Contact of E&M port is opened. | ||
| 1.3.6.1.4.1.6926.1.41.163 | NodeoaLdCardRestarted | The SNMP trap that is generated when card placed in the corresponding slot was restarted. | ||
| 1.3.6.1.4.1.6926.1.41.164 | NoderedundantCardPrimaryRxOn | The SNMP trap that is generated when on redundant card the Primary fiber Receive status is changed to On | ||
| 1.3.6.1.4.1.6926.1.41.165 | NoderedundantCardPrimaryRxOff | The SNMP trap that is generated when on redundant card the Primary fiber Receive status is changed to Off | ||
| 1.3.6.1.4.1.6926.1.41.166 | NoderedundantCardSecondaryRxOn | The SNMP trap that is generated when on redundant card the Secondary fiber Receive status is changed to On | ||
| 1.3.6.1.4.1.6926.1.41.167 | NoderedundantCardSecondaryRxOff | The SNMP trap that is generated when on redundant card the Secondary fiber Receive status is changed Off | ||
| 1.3.6.1.4.1.6926.1.41.168 | NodecardPortsPrimaryClockSource | The SNMP trap that is generated when the module's clock source changed to the primary (user selected) port | ||
| 1.3.6.1.4.1.6926.1.41.169 | NodecardPortsNonPrimaryClockSource | The SNMP trap that is generated when the modules's clock source changed to a non-primary port | ||
| 1.3.6.1.4.1.6926.1.41.170 | NodeeyemaxScanningStart | The SNMP trap that is generated when Eyemax Scanning is started on module or on port of module. | ||
| 1.3.6.1.4.1.6926.1.41.171 | NodeeyemaxScanningCompleted | The SNMP trap that is generated when Eyemax Scanning is completed on module or on port of module. | ||
| 1.3.6.1.4.1.6926.1.41.172 | NodepowerBalancingDone | The SNMP trap that is generated when Power Balancing process is successfully completed on port of module. | ||
| 1.3.6.1.4.1.6926.1.41.173 | NodepowerBalancingNegate | The SNMP trap that is generated when results of Power Balancing process are successfully negated on port of module. | ||
| 1.3.6.1.4.1.6926.1.41.174 | NoderebootIsRequestedByUser | The SNMP trap that is generated when the user initiates reboot process on device. |