PDN-ADSL-LINE-EXT-MIB
97 objects
This MIB module is a supplement to the ADSL-LINE-MIB and to the ADSL-LINE-EXT-MIB, the `standard` MIBs, where additional objects are needed to support ADSL modes or flavors not covered in the `standard` MIBs. At the time this MIB was defined, the IETF ADSL MIB Working does not have any work on the 'standard' MIBs planned and/or has not produced a schedule to address ADSL2/ADSL2plus needs. As a result, these objects may be a `temporary' solution until MIBs/Objects are defined or extended to meet the needs of ADSL2/ADSL2plus. The following documents that should be referenced with respect to this MIB: [G.997.1] ITU-T G997.1 `Physical layer management for Digital Subscriber Line (DSL) transceivers', May 2003. [G.991.1 Am 1] ITU-T-G997.1 Amendment 1 `Physical layer management for Digital Subscriber Line (DSL) transceivers Amendment 1', December 2003. [OA 305] Telenor Networks Specification, Specification Number OA 305, `Requirements for equipment to be connected to the local sub-loop in the access network of Telenor. Equipment providing ADSL and PSTN or ISDN Basic Access Services, full unbundled access (service type EDF)', TN-NL-U-T/OA305/0101 2005, Edition 4.1, January 1, 2005. [WT-090] DSL Forum Working Text WT-090 `Protocol Independent Object Model for Managing Next Generation ADSL Technologies', Revision-1, September 2003. [WT-090-4] DSL Forum Working Text WT-090 `Protocol Independent Object Model for Managing Next Generation ADSL Technologies', Revision-4, June 2004. [RFC 2662] Bathrick, G., Ly, F. `ADSL-LINE-MIB', August 1999. [RFC 3440] Ly, F., Bathrick, G. `ADSL-LINE-EXT-MIB', December 2002. Generally the MIB objects are defined using G.997.1 and the MIB objects are arranged using WT-090. ===================================================================== == == == Copyright (C) 2004 Paradyne Corporation. == == == =====================================================================
Imported Objects
| IF-MIB | ifIndex |
| PDN-HEADER-MIB | pdn-interfaces |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Gauge32 Integer32 MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | RowStatus TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.1795.2.24.2.6.24 | IdentitypdnAdslLineExtMIB | This MIB module is a supplement to the ADSL-LINE-MIB and to the ADSL-LINE-EXT-MIB, the `standard` MIBs, where additional objects are needed to support ADSL mod… | ||
| 1.3.6.1.4.1.1795.2.24.2.6.24.0 | NodepdnAdslLineExtNotifications | |||
| 1.3.6.1.4.1.1795.2.24.2.6.24.1 | NodepdnAdslLineExtObjects | |||
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.1 | TablepdnAdslLineExtTable | not-accessible | current | This table extends the adslLineTable in support of an ADSL Line object. The objects pdnAdslLineTransAtucCap, pdnAdslLineTrans- AtucConfig, and pdnAdslLineTrans… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1 | RowpdnAdslLineExtEntry | not-accessible | current | An extended entry in the adslLineTable. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.1 | ColumnpdnAdslLineTransAtucCap | read-only | current | The transmission modes, represented by a bitmask that the ATU-C is capable of supporting. The modes available are limited by the design of the equipment. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.2 | ColumnpdnAdslLineTransAtucConfig | read-write | current | The transmission modes, represented by a bitmask, currently enabled by the ATU-C. The manager can only set those modes that are supported by the ATU-C. An ATU-… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.3 | ColumnpdnAdslLineTransAtucActual | read-only | current | The actual transmission mode of the ATU-C. During ADSL line initialization, the ADSL Transceiver Unit Remote terminal end (ATU-R) will determine the mode used … |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.4 | ColumnpdnAdslLinePowerManagementConfig | read-write | current | This object enables or disables power management functionality. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.5 | ColumnpdnAdslLineSpectrumProfile | read-write | current | The value of this object identifies the row in the ADSL Line Spectrum Profile Table, pdnAdslLineSpectrumProfileTable, which applies for this ADSL line. If this… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.6 | ColumnpdnAdslLinePmMode | read-write | current | The line states the ATU-C or ATU-R may autonomously transition to on this line. It is coded in a bit-map representation (0 if not allowed, 1 if allowed) as fol… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.7 | ColumnpdnAdslLineL0Time | read-write | current | The minimum time, in seconds, between and Exit from the L2 state and the next Entry into the L2 state. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.8 | ColumnpdnAdslLineL2Time | read-write | current | The minimum time, in seconds, between an Entry into the L2 state and the first Power Trim in the L2 state and between two con- secutive Power Trims in the L2 S… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.9 | ColumnpdnAdslLineL2Atpr | read-write | current | The maximum aggregate transmit power reduction, in dB, that can be performed through a single Power Trim in the L2 state. At the time this MIB was produced, th… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.10 | ColumnpdnAdslLineLdsf | read-write | current | Defines whether the line should be forced into the loop diagnostics mode by the near-end ATU on this line. ldsfMode0(1) - 0: Inhibits the near-end ATU from per… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.11 | ColumnpdnAdslLineL2Atprt | read-write | current | This parameter represents the total maximum aggregate transmit power reduction (in dB) that can be performed in an L2 state. This is the sum of all reductions … |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.2 | TablepdnAdslLineSpectrumProfileTable | not-accessible | current | This table contains specific configuration of transmission spectrum and power spectral density related parameters that can be mapped to one of the ADSL lines. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.2.1 | RowpdnAdslLineSpectrumProfileEntry | not-accessible | current | Each entry contains a specific profile for transmission spectrum and power spectral density related parameters. A default profile with an index of `DEFVAL', wi… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.2.1.1 | ColumnpdnAdslLineSpectrumProfileName | not-accessible | current | This object identifies a row in the pdnAdslLineSpectrumProfile- Table. The system will always provide a default profile whose name is `DEFVAL'. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.2.1.2 | ColumnpdnAdslLineSpectrumProfileRowStatus | read-create | current | This object is used to create a new row or modify or delete an existing row in this table. A profile is activated by setting this object to `valid'. Before a p… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.2.1.3 | ColumnpdnAdslLineSpectrumModeSpecificPsdProfile | read-create | current | The value of this object identifies the row(s) in the ADSL Mode-Specific PSD Configuration Table, pdnAdslModeSpecific- PsdConfTable, which applies for this Lin… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.2.1.4 | ColumnpdnAdslLineSpectrumAtucCarMaskProfile | read-create | current | This object identifies one or more rows in the pdnAdslCarMaskTable. The pdnAdslCarMaskTable is a table containing a list of subcarriers to be masked in the dow… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.2.1.5 | ColumnpdnAdslLineSpectrumAturCarMaskProfile | read-create | current | This object identifies one or more rows in the pdnAdslCarMaskTable. The pdnAdslCarMaskTable is a table containing a list of subcarriers to be masked in the dow… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.3 | TablepdnAdslModeSpecificPsdConfTable | not-accessible | current | This table binds an entry indexed by a specific ADSL type or flavor (e.g. ADSL2 or ADSL2+) and indexed by a profile name to a specific DSL PSD Configuration Pr… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.3.1 | RowpdnAdslModeSpecificPsdConfEntry | not-accessible | current | An entry in the table. For each particular ADSL mode or flavor supported (pdnAdslMOdeSpecificPsdConfAdslMode), there will be an entry that points to an entry i… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.3.1.1 | ColumnpdnAdslModeSpecificPsdConfProfileName | not-accessible | current | This object identifies a row in the pdnAdslModeSpecificPsdConfTable. The system will always provide a default profile whose name is 'DEFVAL'. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.3.1.2 | ColumnpdnAdslModeSpecificPsdConfAdslMode | not-accessible | current | This object identifies a row in the pdnAdslModeSpecificPsdConfTable containing parameters specific to a particular ADSL mode or flavor identified by this objec… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.3.1.3 | ColumnpdnAdslModeSpecificPsdConfRowStatus | read-create | current | This object is used to create a new row or modify or delete an existing row in this table. A profile is activated by setting this object to `valid'. Before a p… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.3.1.4 | ColumnpdnAdslModeSpecificPsdConfAdslPsdConfProfile | read-create | current | This object identifies a row in the ADSL PSD Configuration Table, pdnAdslPsdConfTable. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.4 | TablepdnAdslPsdConfTable | not-accessible | current | This table contains power spectral density settings. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.4.1 | RowpdnAdslPsdConfEntry | not-accessible | current | Each entry contains specific power spectral density settings for a particular profile. A default profile for each particular ADSL mode or flavor supporting PSD… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.4.1.1 | ColumnpdnAdslPsdConfProfileName | not-accessible | current | This object identifies a row in the pdnAdslPsdConfTable. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.4.1.2 | ColumnpdnAdslPsdConfRowStatus | read-create | current | This object is used to create a new row or modify or delete an existing row in this table. A profile is activated by setting this object to `valid'. Before a p… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.4.1.3 | ColumnpdnAdslPsdConfAtucMaxNomPsd | read-create | current | Represents the Maximum nominal transmit PSD for the ATU-C. The values range from -80 to -40 dBm/Hz in 0.1 dB steps. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.4.1.4 | ColumnpdnAdslPsdConfAturMaxNomPsd | read-create | current | Represents the Maximum nominal transmit PSD for the ATU-R. The values range from -65 to -38 dBm/Hz in 0.1 dB steps. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.4.1.5 | ColumnpdnAdslPsdConfAtucMaxNomAtp | read-create | current | Represents the Maximum nominal aggregate transmit power for the ATU-C. The values range from 0 to 25.5 dBm in 0.1 dB steps. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.4.1.6 | ColumnpdnAdslPsdConfAturMaxNomAtp | read-create | current | Represents the Maximum nominal aggregate transmit power for the ATU-R. The values range from 0 to 25.5 dBm in 0.1 dB steps. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.4.1.7 | ColumnpdnAdslPsdConfAtucMaxRxPwr | read-create | current | Represents the maximum upstream aggregate receive power over a set of subcarriers (in dBm). The ATU-C shall request an upstream power cutback such that the ups… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.5 | TablepdnAdslCarMaskTable | not-accessible | current | This table contains a list of subcarriers that are to be masked (i.e. not transmitted). Subcarriers that are not entries in this table are not masked. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.5.1 | RowpdnAdslCarMaskEntry | not-accessible | current | Each entry represents a specific subcarrier that is masked for a particular profile. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.5.1.1 | ColumnpdnAdslCarMaskProfileName | not-accessible | current | This object identifies a row in the pdnAdslCarMaskTable based on a profile name. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.5.1.2 | ColumnpdnAdslCarMaskSubCarrierIndex | not-accessible | current | This object identifies a row in the pdnAdslCarMaskTable based on subcarrier that is being masked. The subcarrier index ranges from 0 to (NSCds-1 or NSCus-1 (NS… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.5.1.3 | ColumnpdnAdslCarMaskRowStatus | read-create | current | This object is used to create a new row or delete an existing row in this table. A row is activated by setting this object to active(1). |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.5.1.4 | ColumnpdnAdslCarMaskSubCarrierStatus | read-only | current | This object provides a clear indication that the subcarrier is masked. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.6 | TablepdnAdslLineStatusTable | not-accessible | current | This table contains current line status measurements. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1 | RowpdnAdslLineStatusEntry | not-accessible | current | Each entry represents an interface. i.e. a row in the ifTable. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1.1 | ColumnpdnAdslLineStatusAtucLineAtn | read-only | current | The measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all subcarriers during diagnostics mode and … |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1.2 | ColumnpdnAdslLineStatusAturLineAtn | read-only | current | The measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all subcarriers during diagnostics mode and … |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1.3 | ColumnpdnAdslLineStatusAtucSignalAtn | read-only | current | The measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all subcarriers during showtime. The value 2… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1.4 | ColumnpdnAdslLineStatusAturSignalAtn | read-only | current | The measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all subcarriers during showtime. The value 2… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1.5 | ColumnpdnAdslLineStatusAtucSnrMgn | read-only | current | The upstream signal-to-noise ratio margin is the increase in dB of the noise power received at the ATU-R, such that the BER requirements are met for all upstre… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1.6 | ColumnpdnAdslLineStatusAturSnrMgn | read-only | current | The downstream signal-to-noise ratio margin is the increase in dB of the noise power received at the ATU-C, such that the BER requirements are met for all upst… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1.7 | ColumnpdnAdslLineStatusAtucMaxAttainableLineRate | read-only | current | The maximum downstream net data rate currently attainable by the ATU-C transmitter and the ATU-R receiver. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1.8 | ColumnpdnAdslLineStatusAturMaxAttainableLineRate | read-only | current | The maximum upstream net data rate currently attainable by the ATU-R transmitter and the ATU-C receiver. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1.9 | ColumnpdnAdslLineStatusAtucActAtp | read-only | current | The total amount of transmit power delivered by the ATU-C at the U-R reference point, at the instant of the measurement. The value 2048 is a special value and … |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1.10 | ColumnpdnAdslLineStatusAturActAtp | read-only | current | The total amount of transmit power delivered by the ATU-R at the U-R reference point, at the instant of the measurement. The value 2048 is a special value and … |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.7 | TablepdnAdslLineSubCarStatusTable | not-accessible | current | This table contains current line status measurements. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1 | RowpdnAdslLineSubCarStatusEntry | not-accessible | current | Each entry represents an interface. i.e. a row in the ifTable. Some objects in this table are only valid if a loop diagnostic has successfully completed. Those… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.1 | ColumnpdnAdslLineCarrierIndex | not-accessible | current | Identifies a row in the table based on a subcarrier. The subcarrier index ranges from 0 to (NSCds-1 or NSCus-1 (NSC is Number of Subcarriers) as specified in G… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.2 | ColumnpdnAdslLineSubCarAtucHlinPs | read-only | current | The downstream linear representation, Hlin(f), of the Channel Characteristics Function, H(f). This value is only available after a loop diagnostic procedure. T… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.3 | ColumnpdnAdslLineSubCarAturHlinPs | read-only | current | The upstream linear representation, Hlin(f), of the Channel Characteristics Function, H(f). This value is only available after a loop diagnostic procedure. The… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.4 | ColumnpdnAdslLineSubCarAtucHlogMt | read-only | current | The number of symbols used to measure downstream H(f) logarithmic measurement values. After a loop diagnostic procedure, this parameter shall contain the numbe… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.5 | ColumnpdnAdslLineSubCarAturHlogMt | read-only | current | The number of symbols used to measure downstream H(f) logarithmic measurement values. After a loop diagnostic procedure, this parameter shall contain the numbe… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.6 | ColumnpdnAdslLineSubCarAtucQlnPs | read-only | current | Downstream Quiet Line Noise. The special value 255 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.7 | ColumnpdnAdslLineSubCarAturQlnPs | read-only | current | Upstream Quiet Line Noise. The special value 255 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the n… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.8 | ColumnpdnAdslLineSubCarAtucSnrPs | read-only | current | Downstream Signal-to-Noise Ratio. The special value 255 indicates that no measurement could be done for the subcarrier because it is out of the passband or tha… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.9 | ColumnpdnAdslLineSubCarAturSnrPs | read-only | current | Upstream Signal-to-Noise Ratio. The special value 255 indicates that no measurement could be done for the subcarrier because it is out of the passband or that … |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.10 | ColumnpdnAdslLineSubCarAtucBitsPs | read-only | current | Downstream bits allocation. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.11 | ColumnpdnAdslLineSubCarAturBitsPs | read-only | current | Upstream bits allocation. |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.12 | ColumnpdnAdslLineSubCarAtucHlogPs | read-only | current | The downstream logarithmic representation, Hlog(f), of the Channel Characteristics function, H(f), providing magnitude values. The special value 1023 indicates… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.13 | ColumnpdnAdslLineSubCarAturHlogPs | read-only | current | The upstream logarithmic representation, Hlog(f), of the Channel Characteristics function, H(f), providing magnitude values. The special value 1023 indicates t… |
| 1.3.6.1.4.1.1795.2.24.2.6.24.2 | NodepdnAdslLineExtAFNs | |||
| 1.3.6.1.4.1.1795.2.24.2.6.24.3 | NodepdnAdslLineExtConformance | |||
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.1 | NodepdnAdslLineExtCompliances | |||
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.1.1 | CompliancepdnAdslLineExtMIBCompliance | current | The compliance statement for pdnAdslLineMIB entities which implement the pdnAdslLineMIB. | |
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.2 | NodepdnAdslLineExtGroups | |||
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1 | NodepdnAdslLineExtObjGroups | |||
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.1 | GrouppdnAdslLineExtGroup | current | A collection of objects providing extended configuration information about an ADSL Line. | |
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.2 | GrouppdnAdslLineSpectrumGroup | current | A collection of objects providing transmission spectrum and power spectral density related profiles. | |
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.3 | GrouppdnAdslModeSpecificPsdGroup | current | A collection of objects providing a mapping from an entry into the ADSL Line Spectrum Table to a profile defining a specific set of power spectral density sett… | |
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.4 | GrouppdnAdslPsdGroup | current | A collection of objects providing specific power spectral density settings based on a named profile. | |
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.5 | GrouppdnAdslCarMaskGroup | current | A collection of objects providing the ability for an administrator to mask out specific subcarriers in the downstream or the upstream direction. | |
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.6 | GrouppdnAdslLineL2AtprtGroup | current | Total maximum aggregate transmit power reduction in L2. | |
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.7 | GrouppdnAdslLineStatusLineAtnGroup | current | Line attenuation during diagnostic mode and initialization. | |
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.8 | GrouppdnAdslLineStatusSignalAtnGroup | current | Line attenuation during showtime. | |
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.9 | GrouppdnAdslLineStatusSnrMgnGroup | current | SNR margin ratio. | |
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.10 | GrouppdnAdslLineStatusMaxattainableLineRateGroup | current | Current maximum attainable net data rate. | |
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.11 | GrouppdnAdslLineStatusActAtpGroup | current | Actual aggregate transmit power. | |
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.12 | GrouppdnAdslLineSubCarStatusHlinGroup | current | Linear representation of the Channel Characteristics function for a subcarrier on a line. | |
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.13 | GrouppdnAdslLineSubCarStatusHlogMtGroup | current | Logarithmic measurement time of the Channel Characteristics function for a subcarrier on a line. | |
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.14 | GrouppdnAdslLineSubCarStatusQlnGroup | current | Quiet Line Noise for a subcarrier on a line. | |
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.15 | GrouppdnAdslLineSubCarStatusSnrGroup | current | Signal-to-Noise Ratio for a subcarrier on a line. | |
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.16 | GrouppdnAdslLineSubCarStatusBitsGroup | current | Bits allocation for a subcarrier on a line. | |
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.17 | GrouppdnAdslLineSubCarStatusHlogGroup | current | Logarithmic representation of the Channel Characteristics function for a subcarrier on a line. | |
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.2.2 | NodepdnAdslLineExtAfnGroups | |||
| 1.3.6.1.4.1.1795.2.24.2.6.24.3.2.3 | NodepdnAdslLineExtNtfyGroups |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| PdnAdslTransmissionModeType | BITS { ansit1413(0), etsi(1), q9921PotsNonOverlapped(2), q9921PotsOverlapped(3), q9921IsdnNonOverlapped(4), q9921isdnOverlapped(5), q9921tcmIsdnNonOverlapped(6), q9921tcmIsdnOverlapped(7), q9922potsNonOverlapeed(8), q9922potsOverlapped(9), q9922tcmIsdnNonOverlapped(10), q9922tcmIsdnOverlapped(11), q9921tcmIsdnSymmetric(12), reservedBit13(13), reservedBit14(14), reservedBit15(15), reservedBit16(16), reservedBit17(17), q9923potsNonOverlapped(18), q9923potsOverlapped(19), q9923isdnNonOverlapped(20), q9923isdnOverlapped(21), reservedBit22(22), reservedBit23(23), q9924potsNonOverlapped(24), q9924potsOverlapped(25), reservedBit26(26), reservedBit27(27), q9923DigitalNonOverlappedI(28), q9923DigitalOverlappedI(29), q9923DigitalNonOverlappedJ(30), q9923DigitalOverlappedJ(31), q9924DigitalNonOverlappedI(32), q9924DigitalOverlappedI(33), q9923ReachExtOverPotsMode1L(34), q9923ReachExtOverPotsMode2L(35), q9923ReachExtOverPotsMode3L(36), q9923ReachExtOverPotsMode4L(37), q9923ExtUpOverPotsNonOverlappedM(38), q9923ExtUpOverPotsOverlappedM(39), q9925potsNonOverlapped(40), q9925potsOverlapped(41), q9925isdnNonOverlapped(42), q9925isdnOverlapped(43), reserved44(44), reserved45(45), q9925DigitalNonOverlappedI(46), q9925DigitalOverlappedI(47), q9925DigitalNonOverlappedJ(48), q9925OverlappedJ(49), q9925ExtUpOverPotsNonOverlappedM(50), q9925ExtUpOverPotsOverlappedM(51), reservedBit52(52), reservedBit53(53), reservedBit54(54), reservedBit55(55) } | current | A set of ADSL line transmission modes, with one bit per mode. |