PDN-DOT1QEXT-MIB
25 objects
The Paradyne enterprise DOT1q extension MIB. This MIB provides additional DOT1q configuration objects not provided by rfc2674.
Imported Objects
| IF-MIB | ifIndex |
| PDN-HEADER-MIB | pdn-dot1q |
| PDN-TC | TblCmd |
| Q-BRIDGE-MIB | dot1qVlanStaticEntry |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Integer32 IpAddress MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.1795.2.24.2.39.1 | IdentitypdnDot1qExt | The Paradyne enterprise DOT1q extension MIB. This MIB provides additional DOT1q configuration objects not provided by rfc2674. | ||
| 1.3.6.1.4.1.1795.2.24.2.39.1.1 | NodepdnDot1qExtObjects | |||
| 1.3.6.1.4.1.1795.2.24.2.39.1.1.1 | TablepdnDot1qVlanStaticExtTable | not-accessible | current | The Paradyne dot1qVlanStatic extension table. This table is used for configuring extensions to static vlans. |
| 1.3.6.1.4.1.1795.2.24.2.39.1.1.1.1 | RowpdnDot1qVlanStaticExtEntry | not-accessible | current | An entry in the Paradyne dot1q extension to Static Vlan Table |
| 1.3.6.1.4.1.1795.2.24.2.39.1.1.1.1.1 | ColumnpdnDot1qVlanStaticSecureModeStatus | read-write | current | This is objects configure secure mode status for the selected VLAN. The secure VLAN mode implies that the users on this VLAN cannot talk to users on a differen… |
| 1.3.6.1.4.1.1795.2.24.2.39.1.1.1.1.2 | ColumnpdnDot1qVlanStaticProxyArpStatus | read-write | current | This objects enables/disabled proxy arp on secure VLAN. If the VLAN is secure, it can optionally have Proxy ARP enabled. This object is not valid unless pdnDot… |
| 1.3.6.1.4.1.1795.2.24.2.39.1.1.1.1.3 | ColumnpdnDot1qVlanStaticUplink | read-write | current | This is used to configure the port number of the port on which all frames belonging to secure VLAN are to be forwarded. This object is not valid unless pdnDot1… |
| 1.3.6.1.4.1.1795.2.24.2.39.1.1.1.1.4 | ColumnpdnDot1qVlanStaticDefaultNHR | read-write | current | This object is used to configure Default Next Hop Router Ip Address that would be used only if the Next Hop Router cannot be learned (i.e from snooping message… |
| 1.3.6.1.4.1.1795.2.24.2.39.1.1.1.1.5 | ColumnpdnDot1qVlanStaticOuterTag | read-write | current | When VLAN stacking (Q in Q) is desired, this object contains the value of the outer 802.1q VLAN outer tag. A value of zero (0) indicates that VLAN stacking is … |
| 1.3.6.1.4.1.1795.2.24.2.39.1.1.1.1.6 | ColumnpdnDot1qVlanStaticOuterDefaultPriority | read-write | current | When VLAN stacking (Q in Q) is desired, this object contains the default value of the priority bits in the 802.1q VLAN outer tag for unknown unicast, broadcast… |
| 1.3.6.1.4.1.1795.2.24.2.39.1.1.1.1.7 | ColumnpdnDot1qVlanStaticOuterEthertype | read-write | current | When VLAN stacking (Q in Q) is desired, this object contains the value of the ethertype in the 802.1q VLAN outer tag. If pdnDot1qVlanStaticOuterTag (above) is … |
| 1.3.6.1.4.1.1795.2.24.2.39.1.1.2 | TablepdnDot1BasePortPIWGTable | not-accessible | current | This table allows mapping of Bridge Ports and Priorities. In General, every bridge port has an associated physical port port (identified by its ifIndex). This … |
| 1.3.6.1.4.1.1795.2.24.2.39.1.1.2.1 | RowpdnDot1BasePortPIWGEntry | not-accessible | current | The priority (PIWG) defined on a Bridge port. |
| 1.3.6.1.4.1.1795.2.24.2.39.1.1.2.1.1 | ColumnpdnDot1BasePort | not-accessible | current | This object specifies the bridge port associated with this PIWG |
| 1.3.6.1.4.1.1795.2.24.2.39.1.1.2.1.2 | ColumnpdnDot1BasePortPIWGId | read-only | current | This is the integer identifier of the priority (PIWG) |
| 1.3.6.1.4.1.1795.2.24.2.39.1.1.2.1.3 | ColumnpdnDot1BasePortPIWGCircuit | read-only | current | This is the object identifier of the priority (PIWG), The value of this object must be a valid identifier defined under the Paradyne Enterprise Definitions (pd… |
| 1.3.6.1.4.1.1795.2.24.2.39.1.1.3 | ScalarpdnDot1TpFdbClear | read-write | current | This object is used to perform a clear on the Bridge Forwarding Table (dot1dTpFdbTable). A set operation to this object with the value of 'clear (2)' will clea… |
| 1.3.6.1.4.1.1795.2.24.2.39.1.2 | NodepdnDot1qExtConformance | |||
| 1.3.6.1.4.1.1795.2.24.2.39.1.2.1 | NodepdnDot1qExtGroups | |||
| 1.3.6.1.4.1.1795.2.24.2.39.1.2.1.1 | GrouppdnDot1qVlanExtGroup | current | A collection of configuration objects required for configuring Static Vlan Table. | |
| 1.3.6.1.4.1.1795.2.24.2.39.1.2.1.2 | GrouppdnDot1BasePortPIWGGroup | current | A collection of read-only objects to provide associations between bridge ports and priorities. | |
| 1.3.6.1.4.1.1795.2.24.2.39.1.2.1.3 | GrouppdnDot1GeneralGroup | current | This group is optional, but if suppported it should be read-writtable. | |
| 1.3.6.1.4.1.1795.2.24.2.39.1.2.1.4 | GrouppdnDot1dVlanStackingGroup | current | Provides the ability to configure VLAN Stacking (Q in Q) parameters. | |
| 1.3.6.1.4.1.1795.2.24.2.39.1.2.2 | NodepdnDot1qExtCompliances | |||
| 1.3.6.1.4.1.1795.2.24.2.39.1.2.2.1 | CompliancepdnDot1qExtCompliance | read-only | current | Compliance statement for using this MIB for configuring Dot1q Static Vlan table. |