MIB Viewer

PDN-ETHER-MIB

23 objects
This MIB contains objects that are used to configure ethernet interfaces.
OIDNameAccessStatusDescription
1.3.6.1.4.1.1795.2.24.2.18Identitypdn-etherThis MIB contains objects that are used to configure ethernet interfaces.
1.3.6.1.4.1.1795.2.24.2.18.1NodepdnPortConfigMIBObjects
1.3.6.1.4.1.1795.2.24.2.18.1.1NodepdnPortConfigEthernet
1.3.6.1.4.1.1795.2.24.2.18.1.1.1TablepdnPortConfigEthernetTablenot-accessiblecurrentA Table that contains information about the Ethernet port configuration
1.3.6.1.4.1.1795.2.24.2.18.1.1.1.1RowpdnPortConfigEthernetEntrynot-accessiblecurrentAn entry that contains configuration information about an ethernet Port
1.3.6.1.4.1.1795.2.24.2.18.1.1.1.1.1ColumnpdnPortConfigEthernetDuplexModeread-createcurrentThis object is used to enable or Disable Duplex Mode on an ethernet Port. This object can not be enabled if the auto-negotiate mode is enabled
1.3.6.1.4.1.1795.2.24.2.18.1.1.1.1.2ColumnpdnPortConfigEthernetManageTyperead-createcurrentThis object is used to Enable or Disable Inband or Outband Management.
1.3.6.1.4.1.1795.2.24.2.18.1.1.1.1.3ColumnpdnPortConfigEthernetResetStateread-createcurrentThis object is used to reset the ethernet port.
1.3.6.1.4.1.1795.2.24.2.18.1.1.1.1.4ColumnpdnPortConfigEthernetAutoNegotiateread-createcurrentThis object is used to enable or disable the auto-negotiate mode. Enabling this mode will disable selection of the speed and/or full duplex mode.
1.3.6.1.4.1.1795.2.24.2.18.1.1.1.1.5ColumnpdnPortConfigEthernetSpeedread-createcurrentThis object corresponds to the speed of the ethernet port. This object can not be set if the auto-negotiate mode is enabled.
1.3.6.1.4.1.1795.2.24.2.18.1.2NodepdnPortConfigGroups
1.3.6.1.4.1.1795.2.24.2.18.1.2.1GrouppdnPortConfigEthernetGroupcurrentThis collection of objects is used to set mode and rate on any ethernet interface.
1.3.6.1.4.1.1795.2.24.2.18.1.2.2GrouppdnPortConfigExtMauGroupcurrentThis object is used to set xover mode on any ethernet interface.
1.3.6.1.4.1.1795.2.24.2.18.1.2.3GrouppdnPortConfigExtIfJackGroupcurrentThis object is used to set active jack on any ethernet interface supporting more than one jack.
1.3.6.1.4.1.1795.2.24.2.18.1.3NodepdnPortConfigMauExtMIBObject
1.3.6.1.4.1.1795.2.24.2.18.1.3.1TablepdnPortConfigMauExtTablenot-accessiblecurrentA Table that contains configuration information about the Ethernet port configuration and it extends standard MAU table from RFC2668.
1.3.6.1.4.1.1795.2.24.2.18.1.3.1.1RowpdnPortConfigMauExtEntrynot-accessiblecurrentAn entry that contains configuration information about an ethernet Port
1.3.6.1.4.1.1795.2.24.2.18.1.3.1.1.1ColumnpdnPortConfigXoverread-createcurrentThis object is used to configure if crossover or straightthrough cable is used on ethernet interface if the interface is not set for autonegotiontion.
1.3.6.1.4.1.1795.2.24.2.18.1.4NodepdnPortConfigIfJackMIBObject
1.3.6.1.4.1.1795.2.24.2.18.1.4.1TablepdnIfJackTablenot-accessiblecurrentThis table conceptually extends the ifJackTable but not as an augmentation. See the note above.
1.3.6.1.4.1.1795.2.24.2.18.1.4.1.1RowpdnIfJackEntrynot-accessiblecurrentAn entry that contains configuration information about a jack.
1.3.6.1.4.1.1795.2.24.2.18.1.4.1.1.1ColumnpdnActiveJackread-writecurrentThis object allows the jack type to be configured or a priority to be set. This applies to Ethernet interfaces that may support more than one type of jack on a…
1.3.6.1.4.1.1795.2.24.2.18.2NodepdnPortConfigMIBTraps