POWERCONNECT3048-MIB
108 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | Counter enterprises IpAddress TimeTicks |
| RFC1213-MIB | DisplayString mib-2 PhysAddress |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.674 | Nodedell | |||
| 1.3.6.1.4.1.674.0 | NodeaddressIntrusion | An addressIntrusion trap signifies that an unauthorized address has been seen on the network. | ||
| 1.3.6.1.4.1.674.10895 | NodedellLan | |||
| 1.3.6.1.4.1.674.10895.5 | Nodepowerconnect3048 | |||
| 1.3.6.1.4.1.674.10895.5.1 | NodedellCommGroup | |||
| 1.3.6.1.4.1.674.10895.5.1.1 | TablecommTable | not-accessible | mandatory | A list of SNMP Community Entries |
| 1.3.6.1.4.1.674.10895.5.1.1.1 | RowcommEntry | not-accessible | mandatory | A list of SNMP Community properties |
| 1.3.6.1.4.1.674.10895.5.1.1.1.1 | ColumncommIndex | read-only | mandatory | An index that uniquely identifies an entry in the Community Table. Eight entries are currently supported. |
| 1.3.6.1.4.1.674.10895.5.1.1.1.2 | ColumncommName | read-write | mandatory | The name of this SNMP Community Entry. |
| 1.3.6.1.4.1.674.10895.5.1.1.1.3 | ColumncommGet | read-write | mandatory | The GET permission for the community. A (1) indicates a GET enable. A (2) indicates a GET disable. |
| 1.3.6.1.4.1.674.10895.5.1.1.1.4 | ColumncommSet | read-write | mandatory | The SET permission for the community. A (1) indicates a SET enable. A (2) indicates a SET disable. |
| 1.3.6.1.4.1.674.10895.5.1.1.1.5 | ColumncommTrap | read-write | mandatory | The TRAP permission for the community. A (1) indicates a TRAP enable. A (2) indicates a TRAP disable. |
| 1.3.6.1.4.1.674.10895.5.1.1.1.6 | ColumncommStatus | read-write | mandatory | The RowStatus for the community entry. |
| 1.3.6.1.4.1.674.10895.5.2 | NodedellHostGroup | |||
| 1.3.6.1.4.1.674.10895.5.2.1 | TablehostTable | not-accessible | mandatory | A list of SNMP Trusted Host Entries |
| 1.3.6.1.4.1.674.10895.5.2.1.1 | RowhostEntry | not-accessible | mandatory | A list of SNMP Host properties |
| 1.3.6.1.4.1.674.10895.5.2.1.1.1 | ColumnhostIndex | read-only | mandatory | An index that uniquely identifies an entry in the Host Table. Sixteen entries are currently supported. |
| 1.3.6.1.4.1.674.10895.5.2.1.1.2 | ColumnhostName | read-write | mandatory | The name of this Host Entry. |
| 1.3.6.1.4.1.674.10895.5.2.1.1.3 | ColumnhostIP | read-write | mandatory | The IP Address for the host. |
| 1.3.6.1.4.1.674.10895.5.2.1.1.4 | ColumnhostComm | read-write | mandatory | The name of the community this host belongs to. |
| 1.3.6.1.4.1.674.10895.5.2.1.1.5 | ColumnhostStatus | read-write | mandatory | The RowStatus for the community entry. |
| 1.3.6.1.4.1.674.10895.5.2.2 | ScalarhostAuthorization | read-write | mandatory | If enabled, the host must be in the hostTable in order to access the device via SNMP. |
| 1.3.6.1.4.1.674.10895.5.3 | NodedellMiscGroup | |||
| 1.3.6.1.4.1.674.10895.5.3.1 | ScalarmiscBaud | read-only | mandatory | The Serial port BAUD Rate. |
| 1.3.6.1.4.1.674.10895.5.3.2 | ScalarmiscReset | read-write | mandatory | Physically resets the unit - use with care. A (1) resets the unit, a (2) does nothing. |
| 1.3.6.1.4.1.674.10895.5.3.3 | ScalarmiscStatisticsReset | read-write | mandatory | Resets the units statistics. A (1) resets the unit, a (2) does nothing. |
| 1.3.6.1.4.1.674.10895.5.3.4 | ScalarmiscSwitchOperState | read-only | current | Global operation state of the switch. |
| 1.3.6.1.4.1.674.10895.5.4 | NodedellSpanGroup | |||
| 1.3.6.1.4.1.674.10895.5.4.1 | ScalarspanOnOff | read-write | mandatory | Enable/Disable Spanning Tree. A (1) enables, a (2) disables. |
| 1.3.6.1.4.1.674.10895.5.11 | NodedellConfigGroup | |||
| 1.3.6.1.4.1.674.10895.5.11.1 | ScalarconfigVerSwPrimary | read-only | mandatory | The software image version string |
| 1.3.6.1.4.1.674.10895.5.11.2 | ScalarconfigVerHwChipSet | read-only | mandatory | The hardware chipset version string |
| 1.3.6.1.4.1.674.10895.5.11.3 | ScalarconfigBootMode | read-write | mandatory | Defines the method used for downloading the image when reset. |
| 1.3.6.1.4.1.674.10895.5.11.4 | ScalarconfigBootFtpServerIp | read-write | mandatory | The FTP server's IP address used for downloading the boot image |
| 1.3.6.1.4.1.674.10895.5.11.5 | ScalarconfigBootImageFileName | read-write | mandatory | The path and filename of the boot image to download |
| 1.3.6.1.4.1.674.10895.5.11.6 | TableconfigPortTable | not-accessible | mandatory | A list of interface entries used for enterprise specific configuration. The number of entries is given by the value of ifNumber. All interface entries are assu… |
| 1.3.6.1.4.1.674.10895.5.11.6.1 | RowconfigPortEntry | not-accessible | mandatory | An enterprise specific interface entry. |
| 1.3.6.1.4.1.674.10895.5.11.6.1.1 | ColumnconfigPort | read-write | mandatory | A unique value for each interface that correlates to ifIndex. Its value ranges between 1 and the value of ifNumber. |
| 1.3.6.1.4.1.674.10895.5.11.6.1.3 | ColumnconfigPortDuplex | read-write | mandatory | The port's duplex desired state. |
| 1.3.6.1.4.1.674.10895.5.11.6.1.4 | ColumnconfigPortRuntFilt | read-write | mandatory | Defines whether the port will drop runt packets |
| 1.3.6.1.4.1.674.10895.5.11.6.1.5 | ColumnconfigPortSrcSecurity | read-write | mandatory | The desired state for an interface's source security. |
| 1.3.6.1.4.1.674.10895.5.11.6.1.6 | ColumnconfigPortDataRate | read-write | mandatory | The port's desired transmission data rate. |
| 1.3.6.1.4.1.674.10895.5.11.6.1.7 | ColumnconfigForwardingMode | read-write | mandatory | Indicates whether the packets will receive the entire packet before forwarding. 'store-and-forward' receives the entire packet before forwarding. 'cut-through'… |
| 1.3.6.1.4.1.674.10895.5.11.6.1.8 | ColumnconfigPortDuplexOper | read-only | mandatory | The port's duplex state. |
| 1.3.6.1.4.1.674.10895.5.11.6.1.9 | ColumnconfigPortDataRateOper | read-only | mandatory | The port's transmission data rate. |
| 1.3.6.1.4.1.674.10895.5.11.6.1.10 | ColumnconfigPortStateOper | read-only | mandatory | The port's current state. |
| 1.3.6.1.4.1.674.10895.5.11.6.1.11 | ColumnconfigPortFlowControl | read-write | mandatory | The port will avoid transmitting a new packet for the period of time specified in a received PAUSE packet when enabled. |
| 1.3.6.1.4.1.674.10895.5.11.6.1.12 | ColumnconfigPortDefaultVlanId | read-write | mandatory | The port will add this vlan id tag to any incoming packet which is lacking a vlan id tag. |
| 1.3.6.1.4.1.674.10895.5.11.6.1.13 | ColumnconfigPortComments | read-write | mandatory | May contain any comments related to a given port such as a user name or LAN segment. |
| 1.3.6.1.4.1.674.10895.5.11.6.1.14 | ColumnconfigPortAutoNegotiation | read-write | mandatory | The port will perform auto-negotiation to determine the port's duplex and data rate. When auto-negotiation is enabled, the negotiated duplex and data rate can … |
| 1.3.6.1.4.1.674.10895.5.11.6.1.15 | ColumnconfigPortHOLBlocking | read-write | mandatory | When enabled, the port will prevent head-of-line blocking from occuring. If the current port is to forward a packet to a port which is beleived to be blocked, … |
| 1.3.6.1.4.1.674.10895.5.11.6.1.16 | ColumnconfigPortFlowControlOper | read-only | mandatory | The port's current flow control state. |
| 1.3.6.1.4.1.674.10895.5.11.6.1.17 | ColumnconfigPortGBIC | read-write | mandatory | Port Type. |
| 1.3.6.1.4.1.674.10895.5.11.6.1.18 | ColumnconfigPortFastLink | read-write | mandatory | The port's FastLink option. |
| 1.3.6.1.4.1.674.10895.5.11.6.1.19 | ColumnconfigPortPriority | read-write | mandatory | The port's current flow control state. |
| 1.3.6.1.4.1.674.10895.5.11.7 | ScalarconfigRmonOnOff | read-write | mandatory | Enable or disable Remote Montioring, RMON. |
| 1.3.6.1.4.1.674.10895.5.11.8 | ScalarconfigMirroringOnOff | read-write | mandatory | Enable or disable port mirroring. |
| 1.3.6.1.4.1.674.10895.5.11.9 | ScalarconfigMirrorSrc | read-write | mandatory | When mirroring is enabled (configMirroringOnOff = enabled), this identifies the mirroring source port. This value has a valid range of 1 to ifNumber when enbal… |
| 1.3.6.1.4.1.674.10895.5.11.10 | ScalarconfigMirrorMon | read-write | mandatory | When mirroring is enabled (configMirroringOnOff = enabled), this identifies the mirroring monitoring port. This value has a valid range of 1 to ifNumber when e… |
| 1.3.6.1.4.1.674.10895.5.11.12 | ScalarconfigIpAssignmentMode | read-write | mandatory | Indicates whether the device address is assigned by the user (manual), BootP, or DHCP. |
| 1.3.6.1.4.1.674.10895.5.11.13 | ScalarconfigPhysAddress | read-only | mandatory | The interface's address at the protocol layer immediately 'below' the network layer in the protocol stack. This is the physical address for the end-station. |
| 1.3.6.1.4.1.674.10895.5.11.14 | ScalarconfigPasswordUser | write-only | mandatory | The user password. |
| 1.3.6.1.4.1.674.10895.5.11.15 | ScalarconfigPasswordAdmin | write-only | mandatory | The adminstrator password |
| 1.3.6.1.4.1.674.10895.5.11.16 | ScalarconfigIpAddress | read-write | mandatory | The IP Address for the RDU box. |
| 1.3.6.1.4.1.674.10895.5.11.17 | ScalarconfigNetMask | read-write | mandatory | The network mask for the RDU box. |
| 1.3.6.1.4.1.674.10895.5.11.18 | ScalarconfigGateway | read-write | mandatory | The Gatway Address for the RDU box. |
| 1.3.6.1.4.1.674.10895.5.11.19 | ScalarconfigSave | read-write | mandatory | Physically saves the current configuration to nvram. - use with care. (1) saves the configuration (2) does nothing. |
| 1.3.6.1.4.1.674.10895.5.11.20 | ScalarconfigVerifyPassword | write-only | mandatory | Verify the password is valid. If invalid a BAD_VALUE error is returned. |
| 1.3.6.1.4.1.674.10895.5.11.21 | ScalarconfigVerBootRomImage | read-only | mandatory | The Boot ROM version string |
| 1.3.6.1.4.1.674.10895.5.11.22 | ScalarconfigRestoreDefaults | read-write | mandatory | Restores the configuration of the unit to the original settings. |
| 1.3.6.1.4.1.674.10895.5.11.23 | ScalarconfigIGMPOnOff | read-write | mandatory | Enable or disable the IGMP protocol within the switch. |
| 1.3.6.1.4.1.674.10895.5.11.24 | ScalarconfigWebOnOff | read-write | mandatory | Enable or disable the Web Interface. |
| 1.3.6.1.4.1.674.10895.5.11.25 | ScalarconfigHighPriorityOptimization | read-write | mandatory | Enable or disable high priority optimization. |
| 1.3.6.1.4.1.674.10895.5.11.26 | ScalarconfigDynamicAddressLearning | read-write | mandatory | The ablility to learn dynamic addresses automatically. With this parameter disabled, a new address detected on a port will cause that port to be disabled, forc… |
| 1.3.6.1.4.1.674.10895.5.11.27 | ScalarconfigUserAuthenticationMode | read-write | mandatory | Determines whether the user password will be authenticated by the switch, a remote RADIUS server, or some combination of the two. |
| 1.3.6.1.4.1.674.10895.5.11.28 | ScalarconfigRadiusServerIpAddress | read-write | mandatory | The IP Address of the RADIUS server used for remote user authentication. |
| 1.3.6.1.4.1.674.10895.5.11.29 | ScalarconfigRadiusSharedSecret | read-write | mandatory | A string of characters used in the RADIUS password encryption process. |
| 1.3.6.1.4.1.674.10895.5.11.30 | ScalarconfigTelnetConsole | read-write | mandatory | Enable or disable the telnet console. |
| 1.3.6.1.4.1.674.10895.5.11.31 | TableconfigDiffServTable | not-accessible | mandatory | A list of DSCP Priorities. |
| 1.3.6.1.4.1.674.10895.5.11.31.1 | RowconfigDiffServEntry | not-accessible | mandatory | An enterprise specific DSCP entry. |
| 1.3.6.1.4.1.674.10895.5.11.31.1.1 | ColumnconfigDiffServDSCP | read-only | mandatory | A DSCP value. |
| 1.3.6.1.4.1.674.10895.5.11.31.1.2 | ColumnconfigDiffServPriority | read-write | mandatory | The DSCP's current priority setting. |
| 1.3.6.1.4.1.674.10895.5.11.32 | ScalarconfigTftpServerIpAddress | read-write | mandatory | The IP Address of the tftp server used to upload and download configuration files. This object is to be used in conjunction with configTftpServerFileName and c… |
| 1.3.6.1.4.1.674.10895.5.11.33 | ScalarconfigTftpServerFileName | read-write | mandatory | The filename, including the path, used to store or retrieve a configuration file from the tftp server. This object is to be used in conjunction with configTftp… |
| 1.3.6.1.4.1.674.10895.5.11.34 | ScalarconfigTftpOperation | read-write | mandatory | The tftp operation to perform. Either download a configuration to the unit or upload the current configuration to the tftp server. This object is to be used in… |
| 1.3.6.1.4.1.674.10895.5.11.35 | ScalarconfigIpFilter | read-write | mandatory | Determines if access to the device is limited to only those IP addresses specified in the configIpFilterTable. |
| 1.3.6.1.4.1.674.10895.5.11.36 | TableconfigIpFilterTable | not-accessible | mandatory | A list of IP addresses allowed access to this device. |
| 1.3.6.1.4.1.674.10895.5.11.36.1 | RowconfigIpFilterEntry | not-accessible | mandatory | An enterprise specific IP filter entry. |
| 1.3.6.1.4.1.674.10895.5.11.36.1.1 | ColumnconfigIpFilterIpAddress | read-only | mandatory | An IP address which is allowed access to this device. |
| 1.3.6.1.4.1.674.10895.5.11.36.1.2 | ColumnconfigIpFilterStatus | read-write | mandatory | The status of an entry in the IP filter Table. Only a subset of the rowstatus variables (active, destroy) are available. |
| 1.3.6.1.4.1.674.10895.5.13 | NodedellVlanGroup | |||
| 1.3.6.1.4.1.674.10895.5.13.1 | TablevlanTable | not-accessible | mandatory | A list of the VLANs |
| 1.3.6.1.4.1.674.10895.5.13.1.1 | RowvlanEntry | not-accessible | mandatory | A VLAN entry containing the VLAN id and name. |
| 1.3.6.1.4.1.674.10895.5.13.1.1.1 | ColumnvlanId | read-only | mandatory | The VLAN identifier. A maximum of 16 VLANs is supported. The value must be from 0 to 4095. |
| 1.3.6.1.4.1.674.10895.5.13.1.1.2 | ColumnvlanName | read-write | mandatory | The VLAN name associated with the VLAN Id. |
| 1.3.6.1.4.1.674.10895.5.13.1.1.3 | ColumnvlanStatus | read-write | mandatory | The status of an entry in the VLAN Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. |
| 1.3.6.1.4.1.674.10895.5.13.2 | TablevlanPortTable | not-accessible | mandatory | A list of ports and their associated VLAN. |
| 1.3.6.1.4.1.674.10895.5.13.2.1 | RowvlanPortEntry | not-accessible | mandatory | Information pertaining to an individual port regarding to which VLAN it belongs. |
| 1.3.6.1.4.1.674.10895.5.13.2.1.1 | ColumnvlanPortPortId | read-only | mandatory | A port identifier that is in the range of 1 to ifNumber. |
| 1.3.6.1.4.1.674.10895.5.13.2.1.2 | ColumnvlanPortVlanId | read-only | mandatory | The VLAN identifier. |
| 1.3.6.1.4.1.674.10895.5.13.2.1.3 | ColumnvlanPortStatus | read-write | mandatory | The status of this port's association within this VLAN. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. |
| 1.3.6.1.4.1.674.10895.5.13.2.1.4 | ColumnvlanPortTaggedMode | read-write | mandatory | The tagged mode of a VLAN port. |
| 1.3.6.1.4.1.674.10895.5.14 | NodedellPortTrunkGroup | |||
| 1.3.6.1.4.1.674.10895.5.14.1 | TableportTrunkTable | not-accessible | mandatory | A list of port trunks and their associated members. |
| 1.3.6.1.4.1.674.10895.5.14.1.1 | RowportTrunkEntry | not-accessible | mandatory | A port trunk entry containing the trunk id and trunk members. |
| 1.3.6.1.4.1.674.10895.5.14.1.1.1 | ColumnportTrunkId | read-only | mandatory | The port trunk identifier. The current range is from 1 to 4. |
| 1.3.6.1.4.1.674.10895.5.14.1.1.2 | ColumnportTrunkMember | read-only | mandatory | A port trunk has four members. |
| 1.3.6.1.4.1.674.10895.5.14.1.1.3 | ColumnportTrunkMemberValue | read-write | mandatory | A port trunk member value indicates which port is a member of the specified trunk. Valid values are in the range from 0 to ifNumber. A zero indicates that no p… |