PPM-IGNIS-MIB
255 objects
PPM IGNIS (ViaLiteHD) MIB This MIB defines the data objects available for use with the ViaLiteHD Web & SNMP Controller module. This MIB is incompatible with the ViaLite Classic MIB. This MIB (as of version 1.2) must be loaded with the PPM-ORG-MIB. This MIB includes OIDs originally defined in the PPM-TRAPS-MIB, and such the PPM-TRAPS-MIB should be replaced with the PPM-IGNIS-V1TRAPS-MIB. Pulse Power & Measurement Ltd. reserves the right to make changes in specifications and all other information contained in this document without prior notice. Pulse Power & Measurement Ltd. grants vendors, end-users, and other interested parties a non-exclusive license to use this specification in connection with the management of Pulse Power & Measurement products.
Imported Objects
| PPM-ORG-MIB | ppm vialiteProducts |
| RFC1155-SMI | IpAddress TimeTicks |
| SNMPv2-SMI | Counter32 MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | DisplayString MacAddress |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.31225.1.1 | Identityignis | PPM IGNIS (ViaLiteHD) MIB This MIB defines the data objects available for use with the ViaLiteHD Web & SNMP Controller module. This MIB is incompatible with th… | ||
| 1.3.6.1.4.1.31225.1.1.1 | NodeignisSystem | |||
| 1.3.6.1.4.1.31225.1.1.1.1 | ScalarproductModel | read-only | current | ViaLiteHD Chassis Type |
| 1.3.6.1.4.1.31225.1.1.1.2 | ScalarsysDate | read-write | current | System date. Formatted as DD/MM/YY. |
| 1.3.6.1.4.1.31225.1.1.1.3 | ScalarsysTime | read-write | current | System time. Formatted as HH:MM:SS. |
| 1.3.6.1.4.1.31225.1.1.1.10 | ScalarsnmpHWrevision | read-only | current | ViaLiteHD Controller hardware version. |
| 1.3.6.1.4.1.31225.1.1.1.11 | ScalarsnmpSWversion | read-only | current | ViaLiteHD Controller software version. |
| 1.3.6.1.4.1.31225.1.1.1.12 | ScalarsnmpMACaddress | read-only | current | MAC address of the ViaLiteHD controller. |
| 1.3.6.1.4.1.31225.1.1.1.13 | ScalarsnmpSerialNumber | read-only | current | ViaLiteHD Controller Serial number. |
| 1.3.6.1.4.1.31225.1.1.1.20 | ScalarsnmpTemp | read-only | current | ViaLiteHD controller internal temperature. Trap threshold set by highTempThreshold (ignisSystem.27). |
| 1.3.6.1.4.1.31225.1.1.1.21 | ScalarsnmpVoltage | read-only | current | ViaLiteHD backplane voltage reading, measured in millivolts. Nominal value 12000mV. Trap thresholds set by lowVoltageThreshold & highVoltageThreshold (ignisSys… |
| 1.3.6.1.4.1.31225.1.1.1.22 | ScalarmcpLEDs | read-only | current | A bitmap representation of the SNMP controller front panel LEDs. Each LED is a 4 bit nibble, encoded as: Off=0x0, Green=0x1, Red=0x3 Nibbles are arranged (LSB-… |
| 1.3.6.1.4.1.31225.1.1.1.23 | ScalarmcpReset | read-write | current | Reset command for the SNMP controller. |
| 1.3.6.1.4.1.31225.1.1.1.25 | Scalarpsu1Status | read-only | current | PSU #1 status. |
| 1.3.6.1.4.1.31225.1.1.1.26 | Scalarpsu2Status | read-only | current | PSU #2 status. |
| 1.3.6.1.4.1.31225.1.1.1.27 | ScalarhighTempThreshold | read-write | current | Controller module internal temperature alarm threshold (in degrees Celsius). Max of 90 degC |
| 1.3.6.1.4.1.31225.1.1.1.28 | ScalarlowVoltageThreshold | read-write | current | Low voltage alarm threshold, in mV. Valid range: 9000-15000mV. |
| 1.3.6.1.4.1.31225.1.1.1.29 | ScalarhighVoltageThreshold | read-write | current | High voltage alarm threshold, in mV. Valid range: 9000-15000mV. |
| 1.3.6.1.4.1.31225.1.1.1.30 | ScalarautoCfgDownload | read-write | current | Enable/disable automatic card configuration. If enabled, when a module is replaced by an exact duplicate, the controller will reconfigure the new module to mat… |
| 1.3.6.1.4.1.31225.1.1.1.31 | ScalardefaulthighTempThreshold | read-only | current | Default internal temperature alarm threshold in deg. celsius. Max of 90 degC |
| 1.3.6.1.4.1.31225.1.1.1.32 | ScalardefaultlowVoltageThreshold | read-only | current | Default low voltage alarm threshold(in mV). |
| 1.3.6.1.4.1.31225.1.1.1.33 | ScalardefaulthighVoltageThreshold | read-only | current | Default high voltage alarm threshold(in mV). |
| 1.3.6.1.4.1.31225.1.1.1.34 | ScalarsysVoltageAlarm | read-only | current | Current status of the system voltage alarm, as configured with lowVoltageThreshold and highVoltageThreshold. 0 = No alarm. -1 = Low voltage alarm. 1 = High vol… |
| 1.3.6.1.4.1.31225.1.1.1.35 | ScalarsysTempAlarm | read-only | current | Current status of the system temperature alarm, as configured with highTempThreshold. 0 = No alarm. 1 = High temperature alarm. |
| 1.3.6.1.4.1.31225.1.1.1.36 | ScalarsnmpPartNumber | read-only | current | ViaLiteHD Controller part number. |
| 1.3.6.1.4.1.31225.1.1.4 | NodeignisSlots | |||
| 1.3.6.1.4.1.31225.1.1.4.1 | TableslotsTable | not-accessible | current | A table detailing the configuration and status information for the modules in the ViaLiteHD chassis |
| 1.3.6.1.4.1.31225.1.1.4.1.1 | RowslotsEntry | not-accessible | current | A single slot entry. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.1 | ColumnmodIx | read-only | current | Module index in slots table. Corresponds to module slot in the ViaLiteHD chassis |
| 1.3.6.1.4.1.31225.1.1.4.1.1.2 | ColumnmodType | read-only | current | Module type. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.3 | ColumnmodPN | read-only | current | Module part number. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.4 | ColumnmodFWPN | read-only | current | Module firmware part number. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.5 | ColumnmodFWVer | read-only | current | Module firmware version and build date/time. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.6 | ColumnmodSN | read-only | current | Module serial number. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.7 | ColumnmodOemNumber | read-only | current | Module OEM number. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.8 | ColumnmodCustomerID | read-only | current | Module customer ID. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.9 | ColumnmodMonLifeCounter | read-only | current | Module working hours counter. Increments every 2 hours of continuous operation. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.10 | ColumnmodMonPanelComp | read-only | current | Module Front Panel type bitmap. Encoded as two 4 bit nibbles (LSNibble for the lower(B) front panel port, MSNibble for the upper (A) front panel port). Port ty… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.11 | ColumnmodMonPanelLEDS | read-only | current | A bitmap representation of the module front panel LEDs. Each LED is a 4 bit nibble, encoded as: Green=0x1, Red=0x3, Red&Flashing=0x7 Nibbles are arranged (LSB-… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.12 | ColumnmodLabel | read-only | current | Module type label. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.13 | ColumnmodFreeText | read-write | current | User defined module name. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.14 | ColumnmodFwDate | read-only | current | Firmware build date |
| 1.3.6.1.4.1.31225.1.1.4.1.1.15 | ColumnmodWaveLenInteger | read-only | current | Optical Wavelength (integer part). Given in nm (truncated) |
| 1.3.6.1.4.1.31225.1.1.4.1.1.16 | ColumnmodWaveLenDecimal | read-only | current | Optical Wavelength (decimal part). Given in 0.01nm |
| 1.3.6.1.4.1.31225.1.1.4.1.1.20 | ColumnmodTx1MonSuppVoltage | read-only | current | Tx1 Current supply voltage measured in mV. Nominal 12000mV |
| 1.3.6.1.4.1.31225.1.1.4.1.1.21 | ColumnmodTx1MonLaserBias | read-only | current | Tx1 Current laser bias current measurement, measured in uA. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.22 | ColumnmodTx1MonLaserPower | read-only | current | Tx1 Current laser power measurement, measured in 10mdBm. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.23 | ColumnmodTx1MonRfPower | read-only | current | Tx1 Current RF power, measured in 10mdBm. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.24 | ColumnmodTx1MonRfGain | read-only | current | Tx1 Current RF gain, measured in 10mdB. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.25 | ColumnmodTx1MonFeedI | read-only | current | Tx1 External feed current [0.1mA]. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.26 | ColumnmodTx1MonFeedV | read-only | current | Tx1 External feed voltage [mV]. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.27 | ColumnmodTx1MonStatus | read-only | current | Bitmap encoding of the current configuration status of the Tx1 module. Bit 0: Laser Status (0=Enabled, 1=Disabled) 1: FSK Tone (Digital Channel) Status (0=Enab… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.28 | ColumnmodTx1MonAlarms | read-only | current | Bitmap encoding of the current alarm status of the Tx1 module. All bits are encoded as 0=NoAlarm 1=Alarm Bit 0: Major Alarm 1: Minor Alarm 2: Laser Alarm 3: Au… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.29 | ColumnmodTx1MonInputPower | read-only | current | Tx1 Input power level, measured in 10mdBm |
| 1.3.6.1.4.1.31225.1.1.4.1.1.30 | ColumnmodTx1MonTECTemprtr | read-only | current | Tx1 Laser TEC (Thermo-Electric Cooler) temperature, measured in degrees Centigrade. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.31 | ColumnmodTx1MonTEC | read-only | current | Tx1 Laser TEC (Thermo-Electric Cooler) current, measured in 0.1mA |
| 1.3.6.1.4.1.31225.1.1.4.1.1.40 | ColumnmodTx2MonSuppVoltage | read-only | current | Tx2 Current supply voltage measured in mV. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.41 | ColumnmodTx2MonLaserBias | read-only | current | Tx2 Current laser bias current measurement [uA]. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.42 | ColumnmodTx2MonLaserPower | read-only | current | Tx2 Current laser power measurement, measured in 10mdBm. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.43 | ColumnmodTx2MonRfPower | read-only | current | Tx2 Current RF power, measured in 10mdBm. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.44 | ColumnmodTx2MonRfGain | read-only | current | Tx2 Current RF gain, measured in 10mdB. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.45 | ColumnmodTx2MonFeedI | read-only | current | Tx2 External feed current [0.1mA]. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.46 | ColumnmodTx2MonFeedV | read-only | current | Tx2 External feed voltage [mV]. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.47 | ColumnmodTx2MonStatus | read-only | current | Bitmap encoding of the current configuration status of the Tx2 module. Bit 0: Laser Status (0=Enabled, 1=Disabled) 1: FSK Tone (Digital Channel) Status (0=Enab… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.48 | ColumnmodTx2MonAlarms | read-only | current | Bitmap encoding of the current alarm status of the Tx2 module. All bits are encoded as 0=NoAlarm 1=Alarm Bit 0: Major Alarm 1: Minor Alarm 2: Laser Alarm 3: Au… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.49 | ColumnmodTx2MonInputPower | read-only | current | Tx2 Input power level, measured in 10mdBm |
| 1.3.6.1.4.1.31225.1.1.4.1.1.60 | ColumnmodTx1CfgGainSoftSet | read-write | current | Tx1 Software Gain Control (SGC) Gain setting, measured in 10mdB |
| 1.3.6.1.4.1.31225.1.1.4.1.1.61 | ColumnmodTx1CfgAgcTarget | read-write | current | Tx1 Automatic Gain Control target, measured in 10mdBm. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.62 | ColumnmodTx1CfgLaserDisable | read-write | current | Module Tx1 Laser enable/disable. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.63 | ColumnmodTx1CfgFskDisable | read-write | current | Module Tx1 FSK Tone (Digital Channel) Enable/disable. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.64 | ColumnmodTx1CfgAgc | read-write | current | Module Tx1 Automatic Gain Control enable/disable. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.65 | ColumnmodTx1CfgSgc | read-write | current | Module Tx1 Software Gain Control enable/disable. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.66 | ColumnmodTx1CfgGpsLoad | read-write | current | Tx1 GPS dummy load enable/disable. If the module does not support GPS mode, this will have no effect. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.67 | ColumnmodTx1CfgRFPlevelHigh | read-write | current | Tx1 Rf Power level alarm high threshold, measured in 10mdBm. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.68 | ColumnmodTx1CfgRFPlevelLow | read-write | current | Tx1 Rf Power level alarm low threshold, measured in 10mdBm. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.69 | ColumnmodTx1CfgLnbAlarm | read-write | current | Tx1 LNB voltage alarm severity. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.70 | ColumnmodTx1CfgTECcontrol | read-only | deprecated | Module Tx1 TEC control enable/disable. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.80 | ColumnmodTx2CfgGainSoftSet | read-write | current | Tx2 Software Gain Control (SGC) Gain setting, measured in 10mdB |
| 1.3.6.1.4.1.31225.1.1.4.1.1.81 | ColumnmodTx2CfgAgcTarget | read-write | current | Tx2 Automatic Gain Control (AGC) target, measured in 10mdBm. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.82 | ColumnmodTx2CfgLaserDisable | read-write | current | Module Tx2 Laser enable/disable. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.83 | ColumnmodTx2CfgFskDisable | read-write | current | Module Tx2 FSK Tone (Digital Channel) Enable/disable. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.84 | ColumnmodTx2CfgAgc | read-write | current | Module Tx2 Automatic Gain Control (AGC) enable/disable. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.85 | ColumnmodTx2CfgSgc | read-write | current | Module Tx2 Software Gain Control (SGC) enable/disable. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.86 | ColumnmodTx2CfgGpsLoad | read-write | current | Module Tx2 GPS dummy load enable/disable. If the module does not support GPS mode, this will have no effect. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.87 | ColumnmodTx2CfgRFPlevelHigh | read-write | current | Tx2 Rf Power level alarm high threshold, measured in 10mdBm. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.88 | ColumnmodTx2CfgRFPlevelLow | read-write | current | Tx2 RF Power level alarm low threshold, measured in 10mdBm. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.89 | ColumnmodTx2CfgLnbAlarm | read-write | current | Module Tx2 LNB voltage alarm severity. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.100 | ColumnmodTx1InterRange | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.101 | ColumnmodTx1InterBiasSet | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.102 | ColumnmodTx1InterPowerSet | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.103 | ColumnmodTx1InterPowerCal | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.104 | ColumnmodTx1InterGainDef | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.105 | ColumnmodTx1InterRfMonCal | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.106 | ColumnmodTx1InterFskFreqSet | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.107 | ColumnmodTx1InterRfGainCal | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.108 | ColumnmodTx1InterMonitorMask | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.109 | ColumnmodTx1InterAlarmMask | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.120 | ColumnmodTx2InterRange | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.121 | ColumnmodTx2InterBiasSet | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.122 | ColumnmodTx2InterPowerSet | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.123 | ColumnmodTx2InterPowerCal | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.124 | ColumnmodTx2InterGainDef | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.125 | ColumnmodTx2InterRfMonCal | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.126 | ColumnmodTx2InterFskFreqSet | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.127 | ColumnmodTx2InterRfGainCal | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.128 | ColumnmodTx2InterMonitorMask | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.140 | ColumnmodRx1MonSuppVoltage | read-only | current | Rx1 Current supply voltage measured in mV. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.141 | ColumnmodRx1MonRLLBias | read-only | current | Module Rx1 Photodiode received light level [0.01dBm]. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.142 | ColumnmodRx1MonRfPower | read-only | current | Module Rx1 current RF power [mdBm]. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.143 | ColumnmodRx1MonRfGain | read-only | current | Module Rx1 current RF gain [mdB]. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.144 | ColumnmodRx1MonStatus | read-only | current | Bitmap encoding of the current configuration status of the Rx1 module. Bit 0: FSK (Digital Channel) Detection Status (0=Not Detected, 1=Detected) 1: FSK (Digit… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.145 | ColumnmodRx1MonAlarms | read-only | current | Bitmap encoding of the current alarm status of the Rx1 module. All bits are encoded as 0=NoAlarm 1=Alarm Bit 0: Major Alarm 1: Minor Alarm 2: Automatic Gain Co… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.146 | ColumnmodRx1MonOutputPower | read-only | current | Rx1 Current output RF power level, measured in 10mdBm |
| 1.3.6.1.4.1.31225.1.1.4.1.1.160 | ColumnmodRx2MonSuppVoltage | read-only | current | Rx2 Current supply voltage measured value [mV]. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.161 | ColumnmodRx2MonRLLBias | read-only | current | Rx2 Photodiode received light level [0.01dBm]. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.162 | ColumnmodRx2MonRfPower | read-only | current | Rx2 Current RF power [mdBm]. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.163 | ColumnmodRx2MonRfGain | read-only | current | Rx2 Current RF gain [mdB]. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.164 | ColumnmodRx2MonStatus | read-only | current | Bitmap encoding of the current configuration status of the Rx1 module. Bit 0: FSK (Digital Channel) Detection Status (0=Not Detected, 1=Detected) 1: FSK (Digit… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.165 | ColumnmodRx2MonAlarms | read-only | current | Bitmap encoding of the current alarm status of the Rx1 module. All bits are encoded as 0=NoAlarm 1=Alarm Bit 0: Major Alarm 1: Minor Alarm 2: Automatic Gain Co… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.166 | ColumnmodRx2MonOutputPower | read-only | current | Rx2 Current output RF power level, measured in 10mdBm |
| 1.3.6.1.4.1.31225.1.1.4.1.1.180 | ColumnmodRx1CfgGainSoftSet | read-write | current | Rx1 Software Gain Control (SGC) setting measured in 10mdB. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.181 | ColumnmodRx1CfgAgcTarget | read-write | current | Rx1 Automatic Gain Control target, measured in 10mdBm. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.182 | ColumnmodRx1CfgFskDisable | read-write | current | Rx1 Digital Channel Frequency Shift Keying (FSK) enable/disable. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.183 | ColumnmodRx1CfgAgc | read-write | current | Rx1 Automatic Gain Control (AGC) enable/disable. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.184 | ColumnmodRx1CfgSgc | read-write | current | Rx1 Software Gain Control (SGC) enable/disable. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.185 | ColumnmodRx1CfgAgcMode | read-write | current | Rx1 Automatic Gain Control (AGC) mode select. If in AGC RF Level mode, the AGC control loop will adjust the RF gain to maintain a constant RF power output If i… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.186 | ColumnmodRx1CfgGpsLoad | read-write | current | Rx1 GPS dummy load enable/disable. If the module does not support GPS mode, this will have no effect. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.187 | ColumnmodRx1CfgRFPlevelHigh | read-write | current | Rx1 RF Power level alarm high threshold, measured in 10mdBm |
| 1.3.6.1.4.1.31225.1.1.4.1.1.188 | ColumnmodRx1CfgRFPlevelLow | read-write | current | Rx1 RF Power level alarm low threshold, measured in 10mdBm |
| 1.3.6.1.4.1.31225.1.1.4.1.1.200 | ColumnmodRx2CfgGainSoftSet | read-write | current | Rx2 Software Gain Control (SGC) level measured in 10mdB. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.201 | ColumnmodRx2CfgAgcTarget | read-write | current | Rx2 Automatic Gain Control (AGC) target, measured in 10mdBm. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.202 | ColumnmodRx2CfgFskDisable | read-write | current | Rx2 Digital Channel Frequency Shift Keying (FSK) enable/disable. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.203 | ColumnmodRx2CfgAgc | read-write | current | Rx2 Automatic Gain Control (AGC) enable/disable. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.204 | ColumnmodRx2CfgSgc | read-write | current | Rx2 Software Gain Control (SGC) enable/disable. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.205 | ColumnmodRx2CfgAgcMode | read-write | current | Rx2 Automatic Gain Control (AGC) mode select. If in AGC RF Level mode, the AGC control loop will adjust the RF gain to maintain a constant RF power output If i… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.206 | ColumnmodRx2CfgGpsLoad | read-write | current | Rx2 GPS dummy load enable/disable. If the module does not support GPS mode, this will have no effect. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.207 | ColumnmodRx2CfgRFPlevelHigh | read-write | current | Rx2 RF Power level alarm high threshold, measured in 10mdBm |
| 1.3.6.1.4.1.31225.1.1.4.1.1.208 | ColumnmodRx2CfgRFPlevelLow | read-write | current | Rx2 RF Power level alarm low threshold, measured in 10mdBm |
| 1.3.6.1.4.1.31225.1.1.4.1.1.220 | ColumnmodRx1InterRange | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.221 | ColumnmodRx1InterBiasSet | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.222 | ColumnmodRx1InterGainDef | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.223 | ColumnmodRx1InterRfMonCal | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.224 | ColumnmodRx1InterFskFreqSet | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.225 | ColumnmodRx1InterFskSlicSet | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.226 | ColumnmodRx1InterRfGainCal | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.227 | ColumnmodRx1InterMonitorMask | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.228 | ColumnmodRx1InterAlarmMask | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.240 | ColumnmodRx2InterRange | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.241 | ColumnmodRx2InterBiasSet | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.242 | ColumnmodRx2InterGainDef | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.243 | ColumnmodRx2InterRfMonCal | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.244 | ColumnmodRx2InterFskFreqSet | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.245 | ColumnmodRx2InterFskSlicSet | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.246 | ColumnmodRx2InterRfGainCal | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.247 | ColumnmodRx2InterMonitorMask | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.248 | ColumnmodRx2InterAlarmMask | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.260 | ColumnmodAmpMonVcc | read-only | current | Amplifier supply voltage, measured in mV. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.261 | ColumnmodAmpMonTemp | read-only | current | Amplifier temperature, measured in degrees Celsius |
| 1.3.6.1.4.1.31225.1.1.4.1.1.262 | ColumnmodAmp1MonRf | read-only | current | Amplifier 1 Current RF level, measured in 10mdBm. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.263 | ColumnmodAmp1MonRfGain | read-only | current | Amplifier 1 RF gain, measured in 10mdB. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.264 | ColumnmodAmp1MonStatus | read-only | current | Bitmap encoding of the current configuration status of the Amplifier card: Bit 0: Amplifier 2 Automatic Gain Control (AGC) Status (0=Disabled, 1=Enabled) 1: Am… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.265 | ColumnmodAmp1MonAlarms | read-only | current | Bitmap encoding of the current alarm status of the amplifier card: (All alarms encoded as 0=NoAlarm, 1=Alarm) Bit 0: Amplifier 2 RF Gain Alarm 1: Amplifier 2 R… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.280 | ColumnmodAmp2MonRf | read-only | current | Amplifier 2 Current RF level, measured in 10mdBm. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.281 | ColumnmodAmp2MonRfGain | read-only | current | Amplifier 2 RF gain, measured in 10mdBm. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.282 | ColumnmodAmp2MonStatus | read-only | current | Bitmap encoding of the current configuration status of the Amplifier card: Bit 0: Amplifier 1 Automatic Gain Control (AGC) Status (0=Disabled, 1=Enabled) 1: Am… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.283 | ColumnmodAmp2MonAlarms | read-only | current | Bitmap encoding of the current alarm status of the amplifier card: (All alarms encoded as 0=NoAlarm, 1=Alarm) Bit 0: Amplifier 2 RF Gain Alarm 1: Amplifier 2 R… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.300 | ColumnmodAmp1CfgGainSoftSet | read-write | current | Amp 1 Software Gain Control (SGC) gain setting, measured in 10mdB |
| 1.3.6.1.4.1.31225.1.1.4.1.1.301 | ColumnmodAmp1CfgAgcTarget | read-write | current | Amp 1 Automatic Gain Control (AGC) target, measured in 10mdBm. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.302 | ColumnmodAmp1InterRange | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.303 | ColumnmodAmp1InterGainCal | read-only | current | Amp 1 Gain calibration. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.304 | ColumnmodAmp1InterRfMonCal | read-only | current | Amp 1 RF level monitor calibration. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.305 | ColumnmodAmp1InterAgcCtrl | read-write | current | Amp 1 Automatic Gain Control setting. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.320 | ColumnmodAmp2CfgGainSoftSet | read-write | current | Amp 1 Software Gain Control (SGC) gain setting, measured in 10mdB |
| 1.3.6.1.4.1.31225.1.1.4.1.1.321 | ColumnmodAmp2CfgAgcTarget | read-write | current | Amp 2 Automatic Gain Control (AGC) target, measured in 10mdBm. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.322 | ColumnmodAmp2InterRange | read-only | current | Internal system information. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.323 | ColumnmodAmp2InterGainCal | read-only | current | Amp 2 Gain calibration. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.324 | ColumnmodAmp2InterRfMonCal | read-only | current | Amp 2 RF level monitor calibration. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.325 | ColumnmodAmp2InterAgcCtrl | read-write | current | Amp 2 Automatic Gain Control enable/disable. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.330 | ColumnmodAmp1LvlLimitHCtrl | read-write | current | Amp 1 RF Level high alarm threshold, measured in 10mdBm. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.331 | ColumnmodAmp1LvlLimitLCtrl | read-write | current | Amp 1 RF Level low alarm threshold, measured in 10mdBm. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.332 | ColumnmodAmp2LvlLimitHCtrl | read-write | current | Amp 2 RF Level high alarm threshold, measured in 10mdBm. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.333 | ColumnmodAmp2LvlLimitLCtrl | read-write | current | Amp 2 RF Level low alarm threshold, measured in 10mdBm. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.334 | ColumnmodAmpGainAlThCtrl | read-write | current | Amplifier Gain warning threshold, measured in 10mdB. This threshold is measured from the alarm thresholds (typically a low threshold of 15dB, and a high thresh… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.335 | ColumnmodAmpLvlAlThCtrl | read-write | current | Amplifier RF Level warning threshold, measured in 10mdBm. This threshold is measured from the alarm threshold, i.e, if the Alarm threshold is 10dBm, and this w… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.350 | ColumnmodSwtchMonModeSetting | read-only | current | Switch mode status. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.351 | ColumnmodSwtchMonStatus | read-only | current | Bitmap encoding of the current switch status. Bit 0-3: Unused 4: Switch Direction (1=Left, 0=Right) 5-11: Unused 12-13: Front Panel ALM LED status (00=off, 01=… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.352 | ColumnmodSWAlarmBitMap | read-only | current | Bitmap encoding of the current switch alarm status. Bit 0-1: Unused 2: Minor Alarm 3: Major Alarm 4-15: Unused |
| 1.3.6.1.4.1.31225.1.1.4.1.1.355 | ColumnmodSwtchModeSetting | read-write | current | Switch mode control |
| 1.3.6.1.4.1.31225.1.1.4.1.1.360 | ColumnmodLNBAlarmMask | read-write | current | LNB masking for invalid alarms. Bit 0 = major, Bit 8= OLF |
| 1.3.6.1.4.1.31225.1.1.4.1.1.361 | ColumnmodLNBbitAUX | read-write | current | LNB Auxillary Mode setting: ON = Set Vout to +22V nominal. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.362 | ColumnmodLNBbitITEST | read-write | current | LNB Current threshold setting. Options are Low (6mA) or High (12mA) |
| 1.3.6.1.4.1.31225.1.1.4.1.1.363 | ColumnmodLNBbitEN | read-write | current | LNB Module Power block enable. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.364 | ColumnmodLNBbitVSEL | read-write | current | LNB Module Output voltage select. Options are High (18V nominal), or Low (13V Nominal). |
| 1.3.6.1.4.1.31225.1.1.4.1.1.365 | ColumnmodLNBbitLLC | read-write | current | LNB Cable compensation setting. If enabled, the output voltage is boosted by an additional +1V. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.366 | ColumnmodLNBbitTEN | read-write | current | LNB 22kHz tone enable. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.367 | ColumnmodLNBbitTTX | read-write | current | LNB 22kHz tone output switch. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.368 | ColumnmodLNBbitPCL | read-write | current | LNB Current limit mode selector. Static mode uses a simple clamp current limit. Active mode uses a pulsed current limit |
| 1.3.6.1.4.1.31225.1.1.4.1.1.369 | ColumnmodLNBbitOLF | read-only | current | LNB Overload flag. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.370 | ColumnmodLNBbitOTF | read-only | current | LNB Over Temperature flag. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.371 | ColumnmodLNBMonStatus | read-only | current | Bitmap of the current status of the LNB module Bit 0: Power Block Enable (0=Disabled, 1=Enabled) 1: Output Voltage Setting (0=Low(13V), 1=High(18V)) 2: Cable C… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.372 | ColumnmodLNBDIPSwitch | read-only | current | Bitmap of the DIP switch settings on the LNB Module. All bits are encoded as 0=disabled, 1=enabled Bit 0: Power Block Enable 1: High Voltage output 2: Tone 3: … |
| 1.3.6.1.4.1.31225.1.1.4.1.1.373 | ColumnmodLNBAlarmStatus | read-only | current | Bitmap of the LNB alarm status. All bits are encoded as 0=noAlarm, 1= Alarm. Bit 0: Overload Alarm 1: Over Temperature Alarm 2-7: Unused 8: Major Alarm 9: Mino… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.380 | ColumnmodETHMonSupplyVolt | read-only | current | Ethernet module supply voltage, measured in mV |
| 1.3.6.1.4.1.31225.1.1.4.1.1.381 | ColumnmodETHMonLinkdataRate | read-only | current | Ethernet module Fibre Link data rate bitmap. All bits are encoded as 0=noLink, 1=Link). Bit 0-4: Unused 5: Valid 100BASE Link 6: Valid 1000BASE Link 7: Valid L… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.382 | ColumnmodETHMonDataActivity | read-only | current | Ethernet data activity bitmap. Bit 0-2: Unused 3: Activity (0=noActivity, 1=Activity) 4-7: Unused |
| 1.3.6.1.4.1.31225.1.1.4.1.1.383 | ColumnmodETHMonAlarms | read-only | current | Ethernet module alarms bitmap. All bits are encoded as 0=noAlarm, 1=Alarm Bit 0-1: Unused 2: Minor Alarm 3: Major Alarm 4-7: Unused |
| 1.3.6.1.4.1.31225.1.1.4.1.1.384 | ColumnmodETHMonCopperdataRate | read-only | current | Ethernet module Copper Link data rate bitmap. All bits are encoded as 0=noLink, 1=Link). Bit 0-3: Unused 4: Valid 10BASE link 5: Valid 100BASE Link 6: Valid 10… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.385 | ColumnmodETHMonCopperActivity | read-only | current | Ethernet module Copper Link activity bitmap. Bit 0: Unused 1: Duplex (0=Half Duplex, 1=Full Duplex) 2: Collision (0=noCollision, 1=Collision Detected) 3: Activ… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.390 | ColumnmodSERMonLinkdataRate | read-only | current | Serial data module link data rate. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.391 | ColumnmodSERMonDataActivity | read-only | current | Serial data module data activity. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.392 | ColumnmodSERMonSerialAlarm | read-only | current | Serial data alarm bitmap. All bits are encoded as 0=noAlarm, 1=Alarm. Bit 0: Vcc Alarm 1: Laser Power Alarm 2: RLL (Received Light Level) Alarm 3: Temperature … |
| 1.3.6.1.4.1.31225.1.1.4.1.1.393 | ColumnmodSERMonChannel1Type | read-only | current | Serial data - Channel 1 type. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.394 | ColumnmodSERMonChannel2 | read-only | current | Serial data - Channel 2 type. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.395 | ColumnmodSERMonSupplyVolt | read-only | current | Serial data - Supply voltage. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.396 | ColumnmodSERMonLaserPower | read-only | current | Serial Digital Module Laser optical power [10mdBm]. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.397 | ColumnmodSERMonRLLLevel | read-only | current | Serial Digital Module RLL level [10mdBm]. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.398 | ColumnmodSERMonDipManualMode | read-only | current | Serial Digital Module Manual Mode DIP switch status. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.420 | ColumnmodSERCfgChannelRate | read-write | current | Serial Digital Module channel data rate setting. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.421 | ColumnmodSERCfgTTlImpedance | read-write | current | Serial Digital Module TTL Impedance setting. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.422 | ColumnmodSERCfgLaserDisable | read-write | current | Serial Digital Module Laser enable/disable. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.423 | ColumnmodPROCDescription | read-only | current | PROC module description. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.430 | ColumnmodMaintenanceMode | read-write | current | Module Maintenance Mode. When in maintenance mode, a module will not produce events/traps and will not contribute to the summary alarm outputs. Other module OI… |
| 1.3.6.1.4.1.31225.1.1.4.1.1.440 | ColumnmodG6CardMonSupplyVolt | read-only | current | Card supply voltage, measured in mV. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.452 | ColumnmodG6Dev1CfgBiasTSrc | read-write | current | Set bias-t source. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.454 | ColumnmodG6Dev1MonFeedI | read-only | current | External feed current [0.01mA]. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.455 | ColumnmodG6Dev1MonFeedV | read-only | current | External feed voltage [mV]. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.456 | ColumnmodG6Dev1Type | read-only | current | RF device 1 type. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.457 | ColumnmodG6Dev1WaveLenInteger | read-only | current | Optical Wavelength (integer part). Given in nm (truncated) |
| 1.3.6.1.4.1.31225.1.1.4.1.1.458 | ColumnmodG6Dev1WaveLenDecimal | read-only | current | Optical Wavelength (decimal part). Given in 0.01nm |
| 1.3.6.1.4.1.31225.1.1.4.1.1.464 | ColumnmodG6Dev1CfgAFDThr | read-write | current | Antenna fault detection low current threshold |
| 1.3.6.1.4.1.31225.1.1.4.1.1.465 | ColumnmodG6Dev1CfgAFDEn | read-write | current | Antenna fault detection enable |
| 1.3.6.1.4.1.31225.1.1.4.1.1.466 | ColumnmodG6Dev1CfgAGCMode | read-write | current | Enable automatic gain control based on received light level (RLL) |
| 1.3.6.1.4.1.31225.1.1.4.1.1.472 | ColumnmodG6Dev2CfgBiasTSrc | read-write | current | Set bias-t source. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.474 | ColumnmodG6Dev2MonFeedI | read-only | current | External feed current [0.01mA]. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.475 | ColumnmodG6Dev2MonFeedV | read-only | current | External feed voltage [mV]. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.476 | ColumnmodG6Dev2Type | read-only | current | RF device 2 type. |
| 1.3.6.1.4.1.31225.1.1.4.1.1.477 | ColumnmodG6Dev2WaveLenInteger | read-only | current | Optical Wavelength (integer part). Given in nm (truncated) |
| 1.3.6.1.4.1.31225.1.1.4.1.1.478 | ColumnmodG6Dev2WaveLenDecimal | read-only | current | Optical Wavelength (decimal part). Given in 0.01nm |
| 1.3.6.1.4.1.31225.1.1.4.1.1.484 | ColumnmodG6Dev2CfgAFDThr | read-write | current | Antenna fault detection low current threshold |
| 1.3.6.1.4.1.31225.1.1.4.1.1.485 | ColumnmodG6Dev2CfgAFDEn | read-write | current | Antenna fault detection enable |
| 1.3.6.1.4.1.31225.1.1.4.1.1.486 | ColumnmodG6Dev2CfgAGCMode | read-write | current | Enable automatic gain control based on received light level (RLL) |
| 1.3.6.1.4.1.31225.5 | NodeppmTrapHistory | |||
| 1.3.6.1.4.1.31225.5.1 | ScalartrapsLastTrapSeqID | read-only | current | The sequence number of the last trap that was sent by the agent. |
| 1.3.6.1.4.1.31225.5.2 | ScalartrapsTableMaximumSize | read-only | current | The maximum size of the trap history table. |
| 1.3.6.1.4.1.31225.5.3 | TabletrapsTable | not-accessible | current | A table that contains the last trapsTableMaximumSize traps. |
| 1.3.6.1.4.1.31225.5.3.1 | RowtrapsEntry | not-accessible | current | A trap entry to the trap table |
| 1.3.6.1.4.1.31225.5.3.1.1 | ColumntrapsSequenceID | read-only | current | Sequence number of the trap in the last traps table. |
| 1.3.6.1.4.1.31225.5.3.1.2 | ColumntrapsTick | read-only | current | Timetick when the current trap was sent. |
| 1.3.6.1.4.1.31225.5.3.1.3 | ColumntrapsDate | read-only | current | System date when the current trap was sent. |
| 1.3.6.1.4.1.31225.5.3.1.4 | ColumntrapsTime | read-only | current | System time when the current trap was sent. |
| 1.3.6.1.4.1.31225.5.3.1.5 | ColumntrapsSeverity | read-only | current | The severity of the trap instance. |
| 1.3.6.1.4.1.31225.5.3.1.6 | ColumntrapsSpecificType | read-only | current | The specific type of trap instance. |
| 1.3.6.1.4.1.31225.5.3.1.7 | ColumntrapsModuleType | read-only | current | Additional data sent with the trap. This is the module type that generated the trap. |
| 1.3.6.1.4.1.31225.5.3.1.8 | ColumntrapsSlotIndex | read-only | current | Additional data sent with the trap. The module which generated the trap was in this slot in the ViaLiteHD chassis. |
| 1.3.6.1.4.1.31225.5.3.1.9 | ColumntrapsSpecificCard | read-only | current | This define if the upper or lower card generated the trap. |