PRVT-MPLS-TE-MIB
287 objects
This MIB module contains managed object definitions for MPLS Traffic Engineering (TE) as defined in: Extensions to RSVP for LSP Tunnels, Awduche et al, Internet Draft <draft-ietf-mpls-rsvp-lsp-tunnel- 07.txt>, August 2000; Constraint-Based LSP Setup using LDP, B. Jamoussi, Internet Draft <draft-ietf- mpls-cr-ldp-04.txt>, July 2000; Requirements for Traffic Engineering Over MPLS, Awduche, D., J. Malcolm, J., Agogbua, J., O'Dell, M., J. McManus, <rfc2702.txt>, September 1999.
Imported Objects
| IF-MIB | InterfaceIndexOrZero |
| INET-ADDRESS-MIB | InetAddress InetAddressIPv4 InetAddressPrefixLength InetAddressType |
| MPLS-TC-PRIV-STDEXT-MIB | MplsBitRate MplsBurstSize MplsExtendedTunnelId MplsLSPID MplsOwner MplsPathIndex MplsPathIndexOrZero MplsTunnelAffinity MplsTunnelIndex MplsTunnelInstanceIndex TeHopAddress TeHopAddressAS TeHopAddressType TeHopAddressUnnum |
| PRVT-CR-LDP-MIB | mpls |
| PRVT-TEMIB-ENTITY-MIB | prvtMplsTeMibEntityIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks transmission Unsigned32 zeroDotZero |
| SNMPv2-TC | DisplayString RowPointer RowStatus StorageType TEXTUAL-CONVENTION TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.738.1.6.5.2 | IdentitymplsTeMIB | This MIB module contains managed object definitions for MPLS Traffic Engineering (TE) as defined in: Extensions to RSVP for LSP Tunnels, Awduche et al, Interne… | ||
| 1.3.6.1.4.1.738.1.6.5.2.1 | NodemplsTeObjects | |||
| 1.3.6.1.4.1.738.1.6.5.2.1.1 | TablemplsTunnelIndexNextTable | not-accessible | current | This table contains the next available values of mplsTunnelIndex for all entities. |
| 1.3.6.1.4.1.738.1.6.5.2.1.1.1 | RowmplsTunnelIndexNextEntry | not-accessible | current | An entry in this table represents the next available mplsTunnelIndex for a specific TE-MIB entity. This MIB table is indexed by the PRVT-TE-MIB entity Index. |
| 1.3.6.1.4.1.738.1.6.5.2.1.1.1.1 | ColumnmplsTunnelIndexNextIndex | read-only | current | This object contains the next appropriate value to be used for mplsTunnelIndex when creating entries in the mplsTunnelTable. If the number of unassigned entrie… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2 | TablemplsTunnelTable | not-accessible | current | The mplsTunnelTable allows new MPLS tunnels to be created between an LSR and a remote endpoint, and existing tunnels to be reconfigured or removed. Note that o… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1 | RowmplsTunnelEntry | not-accessible | current | An entry in this table represents an MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signaling pro… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.1 | ColumnmplsTunnelIndex | not-accessible | current | Uniquely identifies this row. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.2 | ColumnmplsTunnelInstance | not-accessible | current | Uniquely identifies an instance of a tunnel. It is useful to identify multiple instances of tunnels for the purposes of backup and parallel tunnels. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.3 | ColumnmplsTunnelIngressLSRId | not-accessible | current | Identity of the ingress LSR associated with this tunnel instance. When the MPLS signalling protocol is rsvp(2) this value SHOULD be equal to the Tunnel Sender … |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.4 | ColumnmplsTunnelEgressLSRId | not-accessible | current | Identity of the egress LSR associated with this tunnel instance. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.5 | ColumnmplsTunnelName | read-create | current | The canonical name assigned to the tunnel. This name can be used to refer to the tunnel on the LSRs console port. If mplsTunnelIsIf is set to true then the ifN… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.6 | ColumnmplsTunnelDescr | read-create | current | A textual string containing information about the tunnel. If there is no description this object contains a zero length string. This object is may not be signa… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.7 | ColumnmplsTunnelIsIf | read-create | current | Denotes whether or not this tunnel corresponds to an interface represented in the interfaces group table. Note that if this variable is set to true then the if… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.8 | ColumnmplsTunnelIfIndex | read-create | current | If mplsTunnelIsIf is set to true, then this value contains the LSR-assigned ifIndex which corresponds to an entry in the interfaces table. Otherwise this varia… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.9 | ColumnmplsTunnelOwner | read-only | current | Denotes the entity that created and is responsible for managing this tunnel. This column is automatically filled by the agent on creation of a row. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.10 | ColumnmplsTunnelRole | read-create | current | This value signifies the role that this tunnel entry/instance represents. This value MUST be set to head(1) at the originating point of the tunnel. This value … |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.11 | ColumnmplsTunnelXCPointer | read-create | current | This variable points to a row in the mplsXCTable. This table identifies the segments that compose this tunnel, their characteristics, and relationships to each… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.12 | ColumnmplsTunnelSignallingProto | read-create | current | The signalling protocol, if any, used to setup this tunnel. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.13 | ColumnmplsTunnelSetupPrio | read-create | current | Indicates the setup priority of this tunnel. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.14 | ColumnmplsTunnelHoldingPrio | read-create | current | Indicates the holding priority for this tunnel. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.15 | ColumnmplsTunnelSessionAttributes | read-create | current | This bitmask indicates optional session values for this tunnel. The following describes these bit fields: fastReroute This flag indicates that any tunnel hop m… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.16 | ColumnmplsTunnelLocalProtectInUse | read-create | current | Indicates that the local repair mechanism is in use to maintain this tunnel (usually in the face of an outage of the link it was previously routed over). |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.17 | ColumnmplsTunnelResourcePointer | read-create | current | This variable represents a pointer to the traffic parameter specification for this tunnel. This value may point at an entry in the mplsTunnelResourceEntry to i… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.18 | ColumnmplsTunnelPrimaryInstance | read-only | current | Specifies the instance index of the primary instance of this tunnel. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.19 | ColumnmplsTunnelInstancePriority | read-create | current | This value indicates which priority, in descending order, with 0 indicating the lowest priority, within a group of tunnel instances. A group of tunnel instance… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.20 | ColumnmplsTunnelHopTableIndex | read-create | current | Index into the mplsTunnelHopTable entry that specifies the explicit route hops for this tunnel. This object is meaningful only at the head-end of the tunnel. F… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.21 | ColumnmplsTunnelPathInUse | read-create | current | This value denotes the configured path that was chosen for this tunnel. This value reflects the secondary index into mplsTunnelHopTable. This path may not exac… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.22 | ColumnmplsTunnelARHopTableIndex | read-only | current | Index into the mplsTunnelARHopTable entry that specifies the actual hops traversed by the tunnel. This is automatically updated by the agent when the actual ho… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.23 | ColumnmplsTunnelCHopTableIndex | read-only | current | Index into the mplsTunnelCHopTable entry that specifies the computed hops traversed by the tunnel. This is automatically updated by the agent when computed hop… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.24 | ColumnmplsTunnelIncludeAnyAffinity | read-create | current | A link satisfies the include-any constraint if and only if the constraint is zero, or the link and the constraint have a resource class in common. The field is… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.25 | ColumnmplsTunnelIncludeAllAffinity | read-create | current | A link satisfies the include-all constraint if and only if the link contains all of the administrative groups specified in the constraint. The field is a bitma… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.26 | ColumnmplsTunnelExcludeAnyAffinity | read-create | current | A link satisfies the exclude-any constraint if and only if the link contains none of the administrative groups specified in the constraint. The field is a bitm… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.27 | ColumnmplsTunnelTotalUpTime | read-only | current | This value represents the aggregate up time for all instances of this tunnel, if available. If this value is unavailable, it MUST return a value of 0. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.28 | ColumnmplsTunnelInstanceUpTime | read-only | current | This value identifies the total time that this tunnel instance's operStatus has been Up(1). |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.29 | ColumnmplsTunnelPrimaryUpTime | read-only | current | Specifies the total time the primary instance of this tunnel has been active. The primary instance of this tunnel is defined in mplsTunnelPrimaryInstance. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.30 | ColumnmplsTunnelPathChanges | read-only | current | Specifies the number of times the actual path for this tunnel instance has changed. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.31 | ColumnmplsTunnelLastPathChange | read-only | current | Specifies the time since the last change to the actual path for this tunnel instance. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.32 | ColumnmplsTunnelCreationTime | read-only | current | Specifies the value of SysUpTime when the first instance of this tunnel came into existence. That is, when the value of mplsTunnelOperStatus was first set to u… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.33 | ColumnmplsTunnelStateTransitions | read-only | current | Specifies the number of times the state (mplsTunnelOperStatus) of this tunnel instance has changed. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.34 | ColumnmplsTunnelAdminStatus | read-create | current | Indicates the desired operational status of this tunnel. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.35 | ColumnmplsTunnelOperStatus | read-only | current | Indicates the actual operational status of this tunnel, which is typically but not limited to, a function of the state of individual segments of this tunnel. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.36 | ColumnmplsTunnelRowStatus | read-create | current | This variable is used to create, modify, and/or delete a row in this table. When a row in this table is in active(1) state, no objects in that row can be modif… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.37 | ColumnmplsTunnelStorageType | read-create | current | The storage type for this tunnel entry. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.38 | ColumnmplsTunnelUnnumIf | read-create | current | Denotes whether or not this tunnel corresponds to an unnumbered interface represented in the interfaces group table. This object is only used if mplsTunnelIsIf… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.39 | ColumnmplsTunnelAttributes | read-create | current | This bitmask indicates optional parameters for this tunnel. These bits should be taken in addition to those defined in mplsTunnelSessionAttributes in order to … |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.40 | ColumnmplsTunnelLSPEncoding | read-create | current | This object indicates the encoding of the LSP being requested. It is only required when a generalized label request will be used for this LSP. A value of 0 in … |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.41 | ColumnmplsTunnelSwitchingType | read-create | current | Indicates the type of switching that should be performed on a particular link. This field is needed for links that advertise more than one type of switching ca… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.42 | ColumnmplsTunnelLinkProtection | read-create | current | This bitmask indicates the level of link protection required. A value of zero (no bits set) indicates that any protection may be used. The following describes … |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.43 | ColumnmplsTunnelGPid | read-create | current | This object indicates the payload carried by the LSP.It is only required when GMPLS will be used for this LSP. Only valid if Generalized Label Request is in us… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.44 | ColumnmplsTunnelSecondary | read-create | current | Indicates that the requested LSP is a secondary LSP. This is a GMPLS feature, and should only be used when GMPLS will be be used for this LSP. This object is o… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.45 | ColumnmplsTunnelDirection | read-create | current | Whether this tunnel is unidirectional-incoming, unidirectional-outgoing, bidirectional in hardware, the terminator end of a signalled bidirectional tunnel, the… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.46 | ColumnmplsTunnelPathComp | read-create | current | This value instructs the source node on how to perform path computation on the explicit route specified by the associated entries in the mplsTunnelHopTable. dy… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.47 | ColumnmplsTunnelUpNotRecip | read-create | current | Indicates the address of the upstream recipient for Notify messages relating to this tunnel. This object is only valid when signaling a tunnel using RSVP. It i… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.48 | ColumnmplsTunnelDownNotRecip | read-create | current | Indicates the address of the downstream recipient for Notify messages relating to this tunnel. This object is only valid when signaling a tunnel using RSVP. It… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.49 | ColumnmplsTunnelAdminStatusFlags | read-create | current | Determines the setting of the Admin Status flags in the Admin Status object or TLV, as described in RFC 3471. Setting this field to a non-zero value will resul… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.50 | ColumnmplsTunnelExtraParamsPtr | read-create | current | Some Tunnels will run over transports that can usefully support technology-specific additional parameters (for example, SONET resource usage). Such parameters … |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.51 | ColumnmplsTunnelUseEgressLabel | read-create | current | Whether or not to use an explicit route Label subobject as configured in mplsTunnelEgressLabel. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.52 | ColumnmplsTunnelEgressLabel | read-create | current | The egress control Label in the explicit route, and its length. At ingress, this value must be inserted as the last hop of the explicit route. At egress this i… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.53 | ColumnmplsTunnelEgressLabelType | read-create | current | The C-Type of the egress control Label configured in mplsTunnelEgressLabel. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.54 | ColumnmplsTunnelOmitEROIfOneHop | read-create | current | Indicates whether the explicit route object should be omitted from the Path message when the tunnel consists of just one loose hop. Note that if mplsTunnelHopT… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.55 | ColumnmplsTunnelPrivateData | read-create | current | This object contains the customer defined private data for the forward signaling direction. At ingress it is filled in with the private data present on the MIB… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.56 | ColumnmplsTunnelSrcTNAAddressType | read-create | current | Type of the source TNA address of this tunnel. This field is used for UNI. For standard MPLS and GMPLS, this field must be set to none. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.57 | ColumnmplsTunnelSrcTNAAddress | read-create | current | Source TNA address of this tunnel. This field is only valid if mplsTunnelSrcTNAAddressType is not none. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.58 | ColumnmplsTunnelDestTNAAddressType | read-create | current | Type of the destination TNA address of this tunnel. This field is used for UNI. For standard MPLS and GMPLS, this field must be set to none. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.59 | ColumnmplsTunnelDestTNAAddress | read-create | current | Destination TNA address of this tunnel. This field is only valid if mplsTunnelDestTNAAddressType is not none. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.60 | ColumnmplsTunnelEndToEndRerouting | read-create | current | Indicates that Crankback End to End rerouting should be enabled on this LSP. Setting this flag will cause Rerouting information to be returned to the ingress n… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.62 | ColumnmplsTunnelIsUni | read-create | current | This flag indicates whether the tunnel is to conform to UNI 1.0. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.63 | ColumnmplsTunnelUniServiceLevel | read-create | current | Indicates the UNI service level. It is only valid when _is_uni_ is set to true. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.64 | ColumnmplsTunnelUniEgressLabel | read-create | current | The label to be used at the destination UNI in the forward direction. This field is only valid if one of mplsTunnelIsUni or mplsTunnelIsSpc is set, and must be… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.65 | ColumnmplsTunnelUniEgressLabelType | read-create | current | The C-Type of the forward label to be used at the destination UNI. This field is only valid if one of mplsTunnelIsUni or mplsTunnelIsSpc is set, and must be fi… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.66 | ColumnmplsTunnelUniEgressLabelPort | read-create | current | The logical port identifier used to uniquely identify and select a (forward) data link at the destination UNI. This port identifier is relative to the destinat… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.67 | ColumnmplsTunnelUniRvsEgressLabel | read-create | current | The label to be used at the destination UNI in the reverse direction. This field is only valid if one of mplsTunnelIsUni or mplsTunnelIsSpc is set, and must be… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.68 | ColumnmplsTunnelUniRvsEgressLabelType | read-create | current | The C-Type of the reverse label to be used at the destination UNI. This field is only valid if one of mplsTunnelIsUni or mplsTunnelIsSpc is set, and must be fi… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.69 | ColumnmplsTunnelUniRvsEgressLabelPort | read-create | current | The logical port identifier used to uniquely identify and select a (reverse) data link at the destination UNI. This port identifier is relative to the destinat… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.70 | ColumnmplsTunnelDeletionMode | read-create | current | Whether to use forced or graceful deletion to delete this LSP. This field is ignored if graceful deletion is not allowed in the TE-MIB entity MIB. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.71 | ColumnmplsTunnelUniDiversityListIndex | read-create | current | UNI specific. This field references a prvtMplsTunnelUNIDivListIndex in the mplsTunnelUNIDiversityTable, and defines this list of tunnels to be diverse from. A … |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.72 | ColumnmplsTunnelDiffServIndex | read-create | current | Index into the mplsDiffServTable entry that specifies the L-LSP or E-LSP parameters to signal when setting up the tunnel. If this field is not filled in or is … |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.73 | ColumnmplsTunnelReversePrivateData | read-create | current | This object contains the customer defined private data for the reverse signaling direction. At egress it is initially set by the RRR_EGRESS_TRANSLATE_PRIV_DATA… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.74 | ColumnmplsTunnelFastRerouteMode | read-create | current | Indicates whether or not this tunnel should be protected by a fast reroute mechanism, and if so which method should be used. noFastReroute - no fast reroute pr… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.75 | ColumnmplsTunnelBackupSetupPrio | read-create | current | Setup priority for backup tunnels set up to protect this tunnel. This field is only valid if the mplsTunnelFastRerouteMode above is not noFastReroute. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.76 | ColumnmplsTunnelBackupHoldingPriority | read-create | current | Holding priority for backup tunnels set up to protect this tunnel. This field is only valid if the mplsTunnelFastRerouteMode above is not noFastReroute. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.77 | ColumnmplsTunnelBackupIncAny | read-create | current | Include-any resource affinity for backup tunnels set up to protect this tunnel. A link satisfies the include-any constraint if and only if the constraint is ze… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.78 | ColumnmplsTunnelBackupIncAll | read-create | current | Include-all resource affinity for backup tunnels set up to protect this tunnel. A link satisfies the include-all constraint if and only if the link contains al… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.79 | ColumnmplsTunnelBackupExcAny | read-create | current | Exclude-any resource affinity for backup tunnels set up to protect this tunnel. A link satisfies the exclude-any constraint if and only if the constraint is ze… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.80 | ColumnmplsTunnelBackupBandwidth | read-create | current | The estimated bandwidth required for backup tunnels, in units of 1000 bits/second. A value of zero indicates best-effort. This field is only valid if the mplsT… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.81 | ColumnmplsTunnelBackupMaxHops | read-create | current | The maximum number of extra hops the backup path is allowed to take, from a Point of Local Repair (PLR) to a Merge Point (MP), with PLR and MP excluded in coun… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.84 | ColumnmplsTunnelIsSpc | read-create | current | This flag indicates whether the tunnel is an OIF soft permanent connection (SPC). |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.85 | ColumnmplsTunnelUniIngressLabel | read-create | current | The label to be used for the in-segment at the source UNI-N in the forward direction. This field is only valid if the mplsTunnelIsSpc field is true. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.86 | ColumnmplsTunnelUniIngressLabelType | read-create | current | The C-Type of the forward label to be used for the in-segment at the source UNI-N. This field is only valid if the mplsTunnelIsSpc field is true. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.87 | ColumnmplsTunnelUniIngressLabelPort | read-create | current | The logical port identifier used to uniquely identify and select a (forward) data link for the in-segment at the source UNI-N. This field is only valid if the … |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.88 | ColumnmplsTunnelUniRvsIngrLabel | read-create | current | The label to be used at the source UNI-N for the out-segment in the reverse direction. This field is only valid if the mplsTunnelIsSpc field is true. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.89 | ColumnmplsTunnelUniRvsIngrLabelType | read-create | current | The C-Type of the reverse label to be used for the out-segment at the source UNI-N. This field is only valid if the mplsTunnelIsSpc field is true. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.90 | ColumnmplsTunnelUniRvsIngrLabelPort | read-create | current | The logical port identifier used to uniquely identify and select a data link for the reverse out-segment at the source UNI-N. This field is only valid if the m… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.91 | ColumnmplsTunnelDiffServClassType | read-create | current | DiffServ Class-Type of the LSP as defined in draft-ietf-tewg-diff-te-proto-03. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.92 | ColumnmplsTunnelExtendedProtection | read-create | current | Indicates that the requested LSP should use the extended PROTECTION object as defined in draft-lang-ccamp-gmpls-recovery-e2e-signaling. This is a GMPLS feature… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.93 | ColumnmplsTunnelProtecting | read-create | current | Indicates that the requested LSP is a protecting LSP and not a working LSP. This field is only valid if mplsTunnelExtendedProtection is true. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.94 | ColumnmplsTunnelNotification | read-create | current | Indicates that the control plane message exchange is only used for notification during protection switching. This field is only valid if mplsTunnelExtendedProt… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.95 | ColumnmplsTunnelLspProtection | read-create | current | This field indicates the level of end-to-end protection for this LSP. This field is only valid if mplsTunnelExtendedProtection is true. A value of zero indicat… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.96 | ColumnmplsTunnelAssociatedLspId | read-create | current | The mplsTunnelInstance of an associated tunnel between the same ingress and egress and with the same mplsTunnelIndex. If this field is zero, the associated LSP… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.97 | ColumnmplsTunnelCallIdType | read-create | current | The C-Type of the following CALL ID. This field is insignificant if the mplsTunnelCallId has zero length. This field can only be changed when the Admin Status … |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.98 | ColumnmplsTunnelCallId | read-create | current | The CALL ID to be used on this tunnel, including the address type, International and National segment (if applicable), source transport network element address… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.100 | ColumnmplsTunnelIsIpv6 | read-create | current | Flag indicating whether this tunnel uses IPv6 addresses. If this flag is set, the tunnel may only be activated if - TE-MIB is configured to allow IPv6 tunnels … |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.101 | ColumnmplsTunnelUpNotRecipType | read-create | current | Type of upstream notify recipient address for this tunnel. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.102 | ColumnmplsTunnelDownNotRecipType | read-create | current | Type of downstream notify recipient address for this tunnel. |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.103 | ColumnmplsTunnelMtu | read-create | current | Maximal transfer unit of the tunnel |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.104 | ColumnmplsTunnelRebuildTimer | read-create | current | Defines a period in minutes (0..1440), after which the tunnel will be unconditionally rebuild. The maximal valid value is 1440 minutes (24 hours) |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.105 | ColumnmplsTunnelOperStatusFlags | read-create | current | Flags to extend the information of the tunnel state For the behaviour - bits meaning: tunnelResignalling (1) - This status shows that currently the tunnel has … |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.106 | ColumnmplsTunnelGuardedDest | read-create | current | The guarded destination object specifies which IP destination address the current tunnel protects used with the fast reroute feature. The tunnel must not be fa… |
| 1.3.6.1.4.1.738.1.6.5.2.1.2.1.107 | ColumnmplsTunnelMBBTimeOut | read-create | current | Specifies the timer configuration (in minutes) for Make-before-break (MBB). The default value of this object is 10 minutes. |
| 1.3.6.1.4.1.738.1.6.5.2.1.3 | TablemplsTunnelHopIndexNextTable | not-accessible | current | This table contains the next available values of mplsTunnelHopIndex for all entities. |
| 1.3.6.1.4.1.738.1.6.5.2.1.3.1 | RowmplsTunnelHopIndexNextEntry | not-accessible | current | An entry in this table represents the next available mplsTunnelHopIndex for a specific TE-MIB entity. This MIB table is indexed by the PRVT-TE-MIB entity Index. |
| 1.3.6.1.4.1.738.1.6.5.2.1.3.1.1 | ColumnmplsTunnelHopIndexNextIndex | read-only | current | This object contains an appropriate value to be used for mplsTunnelHopListIndex when creating entries in the mplsTunnelHopTable. If the number of unassigned en… |
| 1.3.6.1.4.1.738.1.6.5.2.1.4 | TablemplsTunnelHopTable | not-accessible | current | The mplsTunnelHopTable is used to indicate the hops, strict or loose, for an MPLS tunnel defined in mplsTunnelTable, when it is established via signaling, for … |
| 1.3.6.1.4.1.738.1.6.5.2.1.4.1 | RowmplsTunnelHopEntry | not-accessible | current | An entry in this table represents a tunnel hop. An entry is created by a network administrator for signaled ERLSP set up by an MPLS signaling protocol. |
| 1.3.6.1.4.1.738.1.6.5.2.1.4.1.1 | ColumnmplsTunnelHopListIndex | not-accessible | current | Primary index into this table identifying a particular explicit route object. |
| 1.3.6.1.4.1.738.1.6.5.2.1.4.1.2 | ColumnmplsTunnelHopPathOptionIndex | not-accessible | current | Secondary index into this table identifying a particular group of hops representing a particular configured path. This is otherwise known as a path option. |
| 1.3.6.1.4.1.738.1.6.5.2.1.4.1.3 | ColumnmplsTunnelHopIndex | not-accessible | current | Secondary index into this table identifying a particular hop. |
| 1.3.6.1.4.1.738.1.6.5.2.1.4.1.4 | ColumnmplsTunnelHopAddrType | read-create | current | The Hop Address Type of this tunnel hop. The value of this object cannot be changed if the value of the corresponding mplsTunnelHopRowStatus object is 'active'… |
| 1.3.6.1.4.1.738.1.6.5.2.1.4.1.5 | ColumnmplsTunnelHopIpAddr | read-create | current | The Tunnel Hop Address for this tunnel hop. The type of this address is determined by the value of the corresponding mplsTunnelHopAddrType. The value of this o… |
| 1.3.6.1.4.1.738.1.6.5.2.1.4.1.6 | ColumnmplsTunnelHopIpPrefixLen | read-create | current | If mplsTunnelHopAddrType is set to ipv4(1) or ipv6(2), then this value will contain an appropriate prefix length for the IP address in object mplsTunnelHopIpAd… |
| 1.3.6.1.4.1.738.1.6.5.2.1.4.1.7 | ColumnmplsTunnelHopAsNumber | read-create | current | If mplsTunnelHopAddrType is set to asnumber(3), then this value will contain the AS number of this hop. Otherwise the agent should set this object to zero- len… |
| 1.3.6.1.4.1.738.1.6.5.2.1.4.1.8 | ColumnmplsTunnelHopAddrUnnum | read-create | current | If mplsTunnelHopAddrType is set to unnum(4) or unnumv6(6), then this value will contain the interface identifier of the unnumbered interface for this hop. This… |
| 1.3.6.1.4.1.738.1.6.5.2.1.4.1.9 | ColumnmplsTunnelHopLspId | read-create | current | If mplsTunnelHopAddrType is set to lspid(5), then this value will contain the LSPID of a tunnel of this hop. The present tunnel being configured is tunneled th… |
| 1.3.6.1.4.1.738.1.6.5.2.1.4.1.10 | ColumnmplsTunnelHopType | read-create | current | Denotes whether this tunnel hop is routed in a strict or loose fashion. The value of this object has no meaning if the mplsTunnelHopInclude object is set to 'f… |
| 1.3.6.1.4.1.738.1.6.5.2.1.4.1.11 | ColumnmplsTunnelHopInclude | read-create | current | If this value is set to true, then this indicates that this hop must be included in the tunnel's path. If this value is set to 'false', then this hop must be a… |
| 1.3.6.1.4.1.738.1.6.5.2.1.4.1.12 | ColumnmplsTunnelHopPathOptionName | read-create | current | The description of this series of hops as they relate to the specified path option. The value of this object SHOULD be the same for each hop in the series that… |
| 1.3.6.1.4.1.738.1.6.5.2.1.4.1.13 | ColumnmplsTunnelHopEntryPathComp | read-create | current | If this value is set to dynamic, then the user should only specify the source and destination of the path and expect that the CSPF will calculate the remainder… |
| 1.3.6.1.4.1.738.1.6.5.2.1.4.1.14 | ColumnmplsTunnelHopRowStatus | read-create | current | This variable is used to create, modify, and/or delete a row in this table. When a row in this table is in active(1) state, no objects in that row can be modif… |
| 1.3.6.1.4.1.738.1.6.5.2.1.4.1.15 | ColumnmplsTunnelHopStorageType | read-create | current | The storage type for this Hop entry. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. |
| 1.3.6.1.4.1.738.1.6.5.2.1.4.1.16 | ColumnmplsTunnelHopLabelStatuses | read-only | current | This bitmask indicates the presence of labels indicated by the mplsTunnelHopExpLabel and mplsTunnelHopExpRvrsLabel objects. For the Present bits, a set bit ind… |
| 1.3.6.1.4.1.738.1.6.5.2.1.4.1.17 | ColumnmplsTunnelHopExpLabelType | read-create | current | Denotes the type of the label configured in mplsTunnelHopExpLabel. |
| 1.3.6.1.4.1.738.1.6.5.2.1.4.1.18 | ColumnmplsTunnelHopExpLabel | read-create | current | If mplsTunnelHopLabelStatuses object indicates that a forward label is present then the label to use on this hop is found in this object. |
| 1.3.6.1.4.1.738.1.6.5.2.1.4.1.19 | ColumnmplsTunnelHopExpRvrsLabelType | read-create | current | Denotes the type of the label configured in mplsTunnelHopExpRvrsLabel. |
| 1.3.6.1.4.1.738.1.6.5.2.1.4.1.20 | ColumnmplsTunnelHopExpRvrsLabel | read-create | current | If the mplsTunnelHopLabelStatuses object indicates that a reverse label is present then the label to use on this hop is found in this object. |
| 1.3.6.1.4.1.738.1.6.5.2.1.5 | TablemplsTunnelResourceIndexNextTable | not-accessible | current | This table contains the next available values of mplsTunnelResourceIndex for all entities. |
| 1.3.6.1.4.1.738.1.6.5.2.1.5.1 | RowmplsTunnelResourceIndexNextEntry | not-accessible | current | An entry in this table represents the next available mplsTunnelResourceIndex for a specific TE-MIB entity. This MIB table is indexed by the PRVT-TE-MIB entity … |
| 1.3.6.1.4.1.738.1.6.5.2.1.5.1.1 | ColumnmplsTunnelResourceIndexNextIndex | read-only | current | This object contains the next appropriate value to be used for mplsTunnelResourceIndex when creating entries in the mplsTunnelResourceTable. If the number of u… |
| 1.3.6.1.4.1.738.1.6.5.2.1.6 | TablemplsTunnelResourceTable | not-accessible | current | The mplsTunnelResourceTable allows a manager to specify which resources are desired for an MPLS tunnel. This table also allows several tunnels to point to a si… |
| 1.3.6.1.4.1.738.1.6.5.2.1.6.1 | RowmplsTunnelResourceEntry | not-accessible | current | An entry in this table represents a set of resources for an MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed b… |
| 1.3.6.1.4.1.738.1.6.5.2.1.6.1.1 | ColumnmplsTunnelResourceIndex | not-accessible | current | Uniquely identifies this row. |
| 1.3.6.1.4.1.738.1.6.5.2.1.6.1.2 | ColumnmplsTunnelResourceMaxRate | read-create | current | The maximum rate in units of 1000 bits/second. Note that setting mplsTunnelResourceMaxRate, mplsTunnelResourceMeanRate, and mplsTunnelResourceMaxBurstSize to 0… |
| 1.3.6.1.4.1.738.1.6.5.2.1.6.1.3 | ColumnmplsTunnelResourceMeanRate | read-create | current | The mean rate in units of 1000 bits/second. This object is copied into an instance of mplsTrafficParamMeanRate in the mplsTrafficParamTable. The OID of this ta… |
| 1.3.6.1.4.1.738.1.6.5.2.1.6.1.4 | ColumnmplsTunnelResourceMaxBurstSize | read-create | current | The maximum burst size in bytes. This object is copied to mplsInSegmentMaxBurstSize of the corresponding in-segment. When resource allocation is performed as r… |
| 1.3.6.1.4.1.738.1.6.5.2.1.6.1.5 | ColumnmplsTunnelResourceMeanBurstSize | read-create | current | The mean burst size in bytes. The implementations which do not implement this variable must return 0 for this value and must not allow a user to set this value. |
| 1.3.6.1.4.1.738.1.6.5.2.1.6.1.6 | ColumnmplsTunnelResourceExBurstSize | read-create | current | The Excess burst size in bytes. The implementations which do not implement this variable must return noSuchObject(0) exception for this object and must not all… |
| 1.3.6.1.4.1.738.1.6.5.2.1.6.1.7 | ColumnmplsTunnelResourceFrequency | read-create | current | The granularity of the availability of committed rate. The implementations which do not implement this variable must return unspecified(1) for this value and m… |
| 1.3.6.1.4.1.738.1.6.5.2.1.6.1.8 | ColumnmplsTunnelResourceWeight | read-create | current | The relative weight for using excess bandwidth above its committed rate. The value of 0 means that weight is not applicable for the CR-LSP. |
| 1.3.6.1.4.1.738.1.6.5.2.1.6.1.9 | ColumnmplsTunnelResourceRowStatus | read-create | current | This variable is used to create, modify, and/or delete a row in this table. |
| 1.3.6.1.4.1.738.1.6.5.2.1.6.1.10 | ColumnmplsTunnelResourceStorageType | read-create | current | This variable indicates the storage type for this object. |
| 1.3.6.1.4.1.738.1.6.5.2.1.7 | TablemplsTunnelARHopTable | not-accessible | current | The mplsTunnelARHopTable is used to indicate the hops, strict or loose, for an MPLS tunnel defined in mplsTunnelTable, as reported by the MPLS signaling protoc… |
| 1.3.6.1.4.1.738.1.6.5.2.1.7.1 | RowmplsTunnelARHopEntry | not-accessible | current | An entry in this table represents a tunnel hop. An entry is created by a network administrator for signaled ERLSP set up by an MPLS signaling protocol. |
| 1.3.6.1.4.1.738.1.6.5.2.1.7.1.1 | ColumnmplsTunnelARHopListIndex | not-accessible | current | Primary index into this table identifying a particular recorded hop list. |
| 1.3.6.1.4.1.738.1.6.5.2.1.7.1.2 | ColumnmplsTunnelARHopIndex | not-accessible | current | Secondary index into this table identifying the particular hop. |
| 1.3.6.1.4.1.738.1.6.5.2.1.7.1.3 | ColumnmplsTunnelARHopAddrType | read-only | current | The Hop Address Type of this tunnel hop. If the type value is set to ipv4(1) or ipv6(2). The tunnel path can be determin using mplsTunnelARHopIpAddr object. mp… |
| 1.3.6.1.4.1.738.1.6.5.2.1.7.1.4 | ColumnmplsTunnelARHopIpAddr | read-only | current | The Tunnel Hop Address for this tunnel hop. The type of this address is determined by the value of the corresponding mplsTunnelARHopAddrType. If mplsTunnelARHo… |
| 1.3.6.1.4.1.738.1.6.5.2.1.7.1.5 | ColumnmplsTunnelARHopAddrUnnum | read-only | current | If mplsTunnelARHopAddrType is set to unnum(4) or unnumv6(6), then this value will contain the interface identifier of the unnumbered interface for this hop. Th… |
| 1.3.6.1.4.1.738.1.6.5.2.1.7.1.6 | ColumnmplsTunnelARHopLspId | read-only | current | If mplsTunnelARHopAddrType is set to lspid(5), then this value will contain the LSP ID of this hop. This object is otherwise insignificant and should contain a… |
| 1.3.6.1.4.1.738.1.6.5.2.1.7.1.7 | ColumnmplsTunnelARHopLabelStatuses | read-only | current | This bitmask indicates the presence and status of labels indicated by the mplsTunnelARHopExpLabel and mplsTunnelARHopExpRvrsLabel objects. For the Present bits… |
| 1.3.6.1.4.1.738.1.6.5.2.1.7.1.8 | ColumnmplsTunnelARHopExpLabelType | read-only | current | The C-Type of the following hop label. This field is insignificant unless mplsTunnelARHopLabelStatuses has the forwardPresent(0) or forwardGlobal(2) bits set. |
| 1.3.6.1.4.1.738.1.6.5.2.1.7.1.9 | ColumnmplsTunnelARHopExpLabel | read-only | current | If mplsTunnelARHopLabelStatus has the present(0) bit set, then this value indicates the label value used for this hop. This object is otherwise insignificant a… |
| 1.3.6.1.4.1.738.1.6.5.2.1.7.1.10 | ColumnmplsTunnelARHopExpRvrsLabelType | read-only | current | The C-Type of the following hop label. This field is insignificant unless mplsTunnelARHopLabelStatuses has the reversePresent(1) or reverseGlobal(3) bits set. |
| 1.3.6.1.4.1.738.1.6.5.2.1.7.1.11 | ColumnmplsTunnelARHopExpRvrsLabel | read-only | current | If the mplsTunnelARHopLabelStatuses object indicates that a reverse label is present then the label in use on this hop is found in this object. |
| 1.3.6.1.4.1.738.1.6.5.2.1.7.1.12 | ColumnmplsTunnelARHopProtection | read-only | current | Availability and usage of protection on the reported link. localAvailable Indicates that the link downstream of this node is protected via a local repair mecha… |
| 1.3.6.1.4.1.738.1.6.5.2.1.8 | TablemplsTunnelCHopTable | not-accessible | current | The mplsTunnelCHopTable is used to indicate the hops, strict or loose, for an MPLS tunnel defined in mplsTunnelTable, as computed by a constraint- based routin… |
| 1.3.6.1.4.1.738.1.6.5.2.1.8.1 | RowmplsTunnelCHopEntry | not-accessible | current | An entry in this table represents a tunnel hop. An entry in this table is created by a constraint- based routing protocol based on the hops specified in the co… |
| 1.3.6.1.4.1.738.1.6.5.2.1.8.1.1 | ColumnmplsTunnelCHopListIndex | not-accessible | current | Primary index into this table identifying a particular computed hop list. |
| 1.3.6.1.4.1.738.1.6.5.2.1.8.1.2 | ColumnmplsTunnelCHopIndex | not-accessible | current | Secondary index into this table identifying the particular hop. |
| 1.3.6.1.4.1.738.1.6.5.2.1.8.1.3 | ColumnmplsTunnelCHopAddrType | read-only | current | The Hop Address Type of this tunnel hop. Note that lspid(5) is a valid option only for tunnels signaled via CRLDP. |
| 1.3.6.1.4.1.738.1.6.5.2.1.8.1.4 | ColumnmplsTunnelCHopIpAddr | read-only | current | The Tunnel Hop Address for this tunnel hop. The type of this address is determined by the value of the corresponding mplsTunnelCHopAddrType. If mplsTunnelCHopA… |
| 1.3.6.1.4.1.738.1.6.5.2.1.8.1.5 | ColumnmplsTunnelCHopIpPrefixLen | read-only | current | If mplsTunnelCHopAddrType is set to ipv4(1) or ipv6(2), then this value will contain an appropriate prefix length for the IP address in object mplsTunnelCHopIp… |
| 1.3.6.1.4.1.738.1.6.5.2.1.8.1.6 | ColumnmplsTunnelCHopAsNumber | read-only | current | If mplsTunnelCHopAddrType is set to asnumber(3), then this value will contain the AS number of this hop. Otherwise the agent should set this object to zero-len… |
| 1.3.6.1.4.1.738.1.6.5.2.1.8.1.7 | ColumnmplsTunnelCHopAddrUnnum | read-only | current | If mplsTunnelCHopAddrType is set to unnum(4) or unnumv6(6), then this value will contain the unnumbered interface identifier of this hop. This object should be… |
| 1.3.6.1.4.1.738.1.6.5.2.1.8.1.8 | ColumnmplsTunnelCHopLspId | read-only | current | If mplsTunnelCHopAddrType is set to lspid(5), then this value will contain the LSP ID of this hop. This object is otherwise insignificant and should contain a … |
| 1.3.6.1.4.1.738.1.6.5.2.1.8.1.9 | ColumnmplsTunnelCHopType | read-only | current | Denotes whether this is tunnel hop is routed in a strict or loose fashion. |
| 1.3.6.1.4.1.738.1.6.5.2.1.8.1.11 | ColumnmplsTunnelCHopLabelStatuses | read-only | current | This bitmask indicates the presence of labels indicated by the mplsTunnelCHopExpLabel and mplsTunnelCHopExpRvrsLabel objects. A set bit indicates that a label … |
| 1.3.6.1.4.1.738.1.6.5.2.1.8.1.12 | ColumnmplsTunnelCHopExpLabelType | read-only | current | The C-Type of the following hop label. This field is insignificant unless mplsTunnelCHopLabelStatuses has the forwardPresent(0) bit set. |
| 1.3.6.1.4.1.738.1.6.5.2.1.8.1.13 | ColumnmplsTunnelCHopExpLabel | read-only | current | The explicit out-segment label to use on the forward path. When this label is used in signaling protocol messages, it is copied byte for byte as is. Therefore,… |
| 1.3.6.1.4.1.738.1.6.5.2.1.8.1.14 | ColumnmplsTunnelCHopExpRvrsLabelType | read-only | current | The C-Type of the following hop label. This field is insignificant unless mplsTunnelCHopLabelStatuses has the reversePresent(0) bit set. |
| 1.3.6.1.4.1.738.1.6.5.2.1.8.1.15 | ColumnmplsTunnelCHopExpRvrsLabel | read-create | current | The explicit in-segment label to use on the reverse path. When this label is used in signaling protocol messages, it is copied byte for byte as is. Therefore, … |
| 1.3.6.1.4.1.738.1.6.5.2.1.9 | TablemplsTunnelPerfTable | not-accessible | current | This table provides per-tunnel MPLS performance information. |
| 1.3.6.1.4.1.738.1.6.5.2.1.9.1 | RowmplsTunnelPerfEntry | not-accessible | current | An entry in this table is created by the LSR for every tunnel. Its is an extension to mplsTunnelEntry. |
| 1.3.6.1.4.1.738.1.6.5.2.1.9.1.1 | ColumnmplsTunnelPerfPackets | read-only | current | Number of packets forwarded by the tunnel. |
| 1.3.6.1.4.1.738.1.6.5.2.1.9.1.2 | ColumnmplsTunnelPerfHCPackets | read-only | current | High capacity counter for number of packets forwarded by the tunnel. |
| 1.3.6.1.4.1.738.1.6.5.2.1.9.1.3 | ColumnmplsTunnelPerfErrors | read-only | current | Number of errored packets. |
| 1.3.6.1.4.1.738.1.6.5.2.1.9.1.4 | ColumnmplsTunnelPerfBytes | read-only | current | Number of bytes forwarded by the tunnel. |
| 1.3.6.1.4.1.738.1.6.5.2.1.9.1.5 | ColumnmplsTunnelPerfHCBytes | read-only | current | High capacity counter for number of bytes forwarded by the tunnel. |
| 1.3.6.1.4.1.738.1.6.5.2.1.10 | TablemplsTunnelCRLDPResTable | not-accessible | current | The mplsTunnelCRLDPResTable allows a manager to specify which CR-LDP-specific resources are desired for an MPLS tunnel if that tunnel is signaled using CR-LDP.… |
| 1.3.6.1.4.1.738.1.6.5.2.1.10.1 | RowmplsTunnelCRLDPResEntry | not-accessible | current | An entry in this table represents a set of resources for an MPLS tunnel established using CRLDP (mplsTunnelSignallingProto equal to crldp (3)). An entry can be… |
| 1.3.6.1.4.1.738.1.6.5.2.1.10.1.2 | ColumnmplsTunnelCRLDPResMeanBurstSize | read-create | current | The mean burst size in bytes. |
| 1.3.6.1.4.1.738.1.6.5.2.1.10.1.3 | ColumnmplsTunnelCRLDPResExBurstSize | read-create | current | The Excess burst size in bytes. |
| 1.3.6.1.4.1.738.1.6.5.2.1.10.1.4 | ColumnmplsTunnelCRLDPResFrequency | read-create | current | The granularity of the availability of committed rate. |
| 1.3.6.1.4.1.738.1.6.5.2.1.10.1.5 | ColumnmplsTunnelCRLDPResWeight | read-create | current | The relative weight for using excess bandwidth above its committed rate. The value of 0 means that weight is not applicable for the CR-LSP. |
| 1.3.6.1.4.1.738.1.6.5.2.1.10.1.6 | ColumnmplsTunnelCRLDPResFlags | read-create | current | The value of the 1 byte Flags conveyed as part of the traffic parameters during the establishment of the CRLSP. The bits in this object are to be interpreted a… |
| 1.3.6.1.4.1.738.1.6.5.2.1.10.1.7 | ColumnmplsTunnelCRLDPResRowStatus | read-create | current | This variable is used to create, modify, and/or delete a row in this table. |
| 1.3.6.1.4.1.738.1.6.5.2.1.10.1.8 | ColumnmplsTunnelCRLDPResStorageType | read-create | current | This variable indicates the storage type for this object. |
| 1.3.6.1.4.1.738.1.6.5.2.1.11 | TablemplsDiffServIndexNextTable | not-accessible | current | This table contains the next available values of mplsDiffServIndex for all entities. |
| 1.3.6.1.4.1.738.1.6.5.2.1.11.1 | RowmplsDiffServIndexNextEntry | not-accessible | current | An entry in this table represents the next available mplsDiffServIndex for a specific TE-MIB entity. This MIB table is indexed by the PRVT-TE-MIB entity Index. |
| 1.3.6.1.4.1.738.1.6.5.2.1.11.1.1 | ColumnmplsDiffServIndexNextIndex | read-only | current | This object contains the next appropriate value to be used for mplsDiffServIndex when creating entries in the mplsDiffServTable. If the number of unassigned en… |
| 1.3.6.1.4.1.738.1.6.5.2.1.12 | TablemplsDiffServTable | not-accessible | current | The mplsDiffServTable allows DiffServ parameters to be configured for DiffServ enabled LSPs signalled by the mplsTunnelTable. If a tunnel is an E-LSP, then fie… |
| 1.3.6.1.4.1.738.1.6.5.2.1.12.1 | RowmplsDiffServEntry | not-accessible | current | An entry in this table represents either a set of 0 - 8 EXP->PHB maps, and the number of such maps, for an E-LSP or a PSC value for an L-LSP. |
| 1.3.6.1.4.1.738.1.6.5.2.1.12.1.1 | ColumnmplsDiffServIndex | not-accessible | current | Uniquely identifies this row. |
| 1.3.6.1.4.1.738.1.6.5.2.1.12.1.2 | ColumnmplsDiffServType | read-create | current | This field must be set to indicate whether this row contains parameters for an E-LSP or an L-LSP. |
| 1.3.6.1.4.1.738.1.6.5.2.1.12.1.3 | ColumnmplsDiffServLLSPPSC | read-create | current | Valid only when mplsDiffServType takes the value l-lsp (1), this field contains the16-bit encoding of the PHB Scheduling Class (PSC) to be used for packets on … |
| 1.3.6.1.4.1.738.1.6.5.2.1.12.1.4 | ColumnmplsDiffServELSPNumPHBs | read-create | current | Valid only when mplsDiffServType takes the value e-lsp (0), this value indicates the number of EXP->PHB maps defined in this row. |
| 1.3.6.1.4.1.738.1.6.5.2.1.12.1.5 | ColumnmplsDiffServELSPPHB0 | read-create | current | Valid only when mplsDiffServType takes the value e-lsp (0), this field contains the 16-bit encoding of the PHB (RFC 3140) which is assigned to packets on this … |
| 1.3.6.1.4.1.738.1.6.5.2.1.12.1.6 | ColumnmplsDiffServELSPPHB1 | read-create | current | Valid only when mplsDiffServType takes the value e-lsp (0), this field contains the 16-bit encoding of the PHB (RFC 3140) which is assigned to packets on this … |
| 1.3.6.1.4.1.738.1.6.5.2.1.12.1.7 | ColumnmplsDiffServELSPPHB2 | read-create | current | Valid only when mplsDiffServType takes the value e-lsp (0), this field contains the 16-bit encoding of the PHB (RFC 3140) which is assigned to packets on this … |
| 1.3.6.1.4.1.738.1.6.5.2.1.12.1.8 | ColumnmplsDiffServELSPPHB3 | read-create | current | Valid only when mplsDiffServType takes the value e-lsp (0), this field contains the 16-bit encoding of the PHB (RFC 3140) which is assigned to packets on this … |
| 1.3.6.1.4.1.738.1.6.5.2.1.12.1.9 | ColumnmplsDiffServELSPPHB4 | read-create | current | Valid only when mplsDiffServType takes the value e-lsp (0), this field contains the 16-bit encoding of the PHB (RFC 3140) which is assigned to packets on this … |
| 1.3.6.1.4.1.738.1.6.5.2.1.12.1.10 | ColumnmplsDiffServELSPPHB5 | read-create | current | Valid only when mplsDiffServType takes the value e-lsp (0), this field contains the 16-bit encoding of the PHB (RFC 3140) which is assigned to packets on this … |
| 1.3.6.1.4.1.738.1.6.5.2.1.12.1.11 | ColumnmplsDiffServELSPPHB6 | read-create | current | Valid only when mplsDiffServType takes the value e-lsp (0), this field contains the 16-bit encoding of the PHB (RFC 3140) which is assigned to packets on this … |
| 1.3.6.1.4.1.738.1.6.5.2.1.12.1.12 | ColumnmplsDiffServELSPPHB7 | read-create | current | Valid only when mplsDiffServType takes the value e-lsp (0), this field contains the 16-bit encoding of the PHB (RFC 3140) which is assigned to packets on this … |
| 1.3.6.1.4.1.738.1.6.5.2.1.12.1.13 | ColumnmplsDiffServRowStatus | read-create | current | This variable is used to create, modify, and/or delete a row in this table. |
| 1.3.6.1.4.1.738.1.6.5.2.1.13 | TableprvtMplsTunnelUNIDvLstIdxNxtTable | not-accessible | current | This table contains the next available values of prvtMplsTunnelUNIDivListIdx for all entities. |
| 1.3.6.1.4.1.738.1.6.5.2.1.13.1 | RowprvtMplsTunnelUNIDvLstIdxNxtEntry | not-accessible | current | An entry in this table represents the next available prvtMplsTunnelUNIDivListIdx for a specific TE-MIB entity. This MIB table is indexed by the PRVT-TE-MIB ent… |
| 1.3.6.1.4.1.738.1.6.5.2.1.13.1.1 | ColumnprvtMplsTunnelUNIDivListIdxNext | read-only | current | This is the next available List Index in the prvtMplsTunnelUNIDiversityTable. |
| 1.3.6.1.4.1.738.1.6.5.2.1.14 | TableprvtMplsTunnelUNIDiversityTable | not-accessible | current | The prvtMplsTunnelUNIDiversityTable is used to indicate which existing tunnels a new UNI Connection is to be diverse from. This table is UNI specific. Each prv… |
| 1.3.6.1.4.1.738.1.6.5.2.1.14.1 | RowprvtMplsTunnelUNIDiversityEntry | not-accessible | current | An entry in this table corresponds to an entry in the mplsTunnelTable. A subsequent Tunnel that references this entry will be created Diverse from the tunnel r… |
| 1.3.6.1.4.1.738.1.6.5.2.1.14.1.2 | ColumnprvtMplsTunnelUNIDivListIdx | not-accessible | current | Primary index into this table identifying a particular list of Diversity requirements. |
| 1.3.6.1.4.1.738.1.6.5.2.1.14.1.3 | ColumnprvtMplsTunnelUNIDivIdx | not-accessible | current | Secondary index into this table identifying a Diversity requirement within the list. |
| 1.3.6.1.4.1.738.1.6.5.2.1.14.1.4 | ColumnprvtMplsTunnelUNIDivRowPointer | read-create | current | This field represents a pointer to the entry in the mplsTunnelTable to which the Diversity requirement applies. The array of longs specified here is configured… |
| 1.3.6.1.4.1.738.1.6.5.2.1.14.1.5 | ColumnprvtMplsTunnelOperStatus | read-only | current | The Oper Status of the mplsTunnelTable row referred to by prvtMplsTunnelUNIDivPointer. If this tunnel is removed from the mplsTunnelTable then this is set to A… |
| 1.3.6.1.4.1.738.1.6.5.2.1.14.1.6 | ColumnprvtMplsTunnelUNIDivRowStatus | read-create | current | This variable is used to create or delete this row. |
| 1.3.6.1.4.1.738.1.6.5.2.1.14.1.7 | ColumnprvtMplsTunnelUNIDivRequirement | read-create | current | This field indicates the Diversity Requirement for the corresponding tunnel. Once an row entry has been created and is oper status 'up' for this tunnel this va… |
| 1.3.6.1.4.1.738.1.6.5.2.1.14.1.8 | ColumnprvtMplsTunnelUNIDivAccess | read-only | current | This field indicates the access (read-only or writable) that the user has over this row entry. The circumstances under which a row is read-only are described a… |
| 1.3.6.1.4.1.738.1.6.5.2.1.15 | TableprvtMplsTunnelTrapEnableTable | not-accessible | current | The prvtMplsTunnelTrapEnable Table allows a manager to enable or disable TRAPs. |
| 1.3.6.1.4.1.738.1.6.5.2.1.15.1 | RowprvtMplsTunnelTrapEnableEntry | not-accessible | current | An entry in this table is used to configure trap support for this instance of TE-MIB |
| 1.3.6.1.4.1.738.1.6.5.2.1.15.1.2 | ColumnmplsTunnelTrapEnable | read-write | current | If this object is true, then it enables the generation of mplsTunnelUp and mplsTunnelDown traps, otherwise these traps are not emitted. |
| 1.3.6.1.4.1.738.1.6.5.2.1.16 | TablemplsTeMibEntityScalarTable | not-accessible | current | The mplsTeMibEntityScalarTable contains all MPLS Tunnel scalars. |
| 1.3.6.1.4.1.738.1.6.5.2.1.16.1 | RowmplsTeMibEntityScalarEntry | not-accessible | current | The mplsTeMibEntityScalarTable contains all MPLS Tunnel scalars. |
| 1.3.6.1.4.1.738.1.6.5.2.1.16.1.2 | ColumnmplsTunnelConfigured | read-only | current | The number of tunnels configured on this device. A tunnel is considered configured if the mplsTunnelRowStatus is active(1). |
| 1.3.6.1.4.1.738.1.6.5.2.1.16.1.3 | ColumnmplsTunnelActive | read-only | current | The number of tunnels active on this device. A tunnel is considered active if the mplsTunnelOperStatus is up(1). |
| 1.3.6.1.4.1.738.1.6.5.2.1.16.1.4 | ColumnmplsTunnelTEDistProto | read-only | current | The traffic engineering distribution protocol(s) used by this LSR. Note that an LSR may support more than one distribution protocol simultaneously. |
| 1.3.6.1.4.1.738.1.6.5.2.1.16.1.5 | ColumnmplsTunnelMaxHops | read-only | current | The maximum number of hops that can be specified for a tunnel on this device. |
| 1.3.6.1.4.1.738.1.6.5.2.1.16.1.6 | ColumnmplsTunnelNotificationMaxRate | read-only | current | This variable indicates the maximum number of notifications issued per second. If events occur more rapidly, the implementation may simply fail to emit these n… |
| 1.3.6.1.4.1.738.1.6.5.2.1.17 | TablemplsTunnelSonetResTable | not-accessible | current | The mplsTunnelSonetResTable allows a manager to specify which Sonet-specific resources are desired for an MPLS tunnel. Note that these attributes are in additi… |
| 1.3.6.1.4.1.738.1.6.5.2.1.17.1 | RowmplsTunnelSonetResEntry | not-accessible | current | An entry in this table represents a set of Sonet resources for an MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instru… |
| 1.3.6.1.4.1.738.1.6.5.2.1.17.1.2 | ColumnmplsTunnelSonetResRCC | read-create | current | Requested Contiguous Concatenation. Indicates the types of contiguous concatenation requested for this LSP. This field is only valid if <lsp_encoding> is SDH o… |
| 1.3.6.1.4.1.738.1.6.5.2.1.17.1.3 | ColumnmplsTunnelSonetResNCC | read-create | current | Requested Number of Contiguous Components. Indicates the number of identical SDH/SONET SPEs/VCs that are requested to be concatenated, as indicated in the <rcc… |
| 1.3.6.1.4.1.738.1.6.5.2.1.17.1.4 | ColumnmplsTunnelSonetResNVC | read-create | current | This field indicates the number of signals that are requested to be virtually concatenated. These signals are all of the same type. This field is valid only if… |
| 1.3.6.1.4.1.738.1.6.5.2.1.17.1.5 | ColumnmplsTunnelSonetResMultiplier | read-create | current | This field is a bit field indicating the number of identical signals that are requested for the LSP. This field is valid only if <lsp_encoding> is SDH or SONET… |
| 1.3.6.1.4.1.738.1.6.5.2.1.17.1.6 | ColumnmplsTunnelSonetResTransparency | read-create | current | This field is a bit field indicating the type of Transparency being requested. Several flags can be combined to provide different types of transparency. Not al… |
| 1.3.6.1.4.1.738.1.6.5.2.1.17.1.7 | ColumnmplsTunnelSonetResRowStatus | read-create | current | This variable is used to create, modify, and/or delete a row in this table. |
| 1.3.6.1.4.1.738.1.6.5.2.1.17.1.9 | ColumnmplsTunnelSonetResSignalType | read-create | current | Indicates the overhead termination type and is interpreted in relation to the LSP Encoding Type. |
| 1.3.6.1.4.1.738.1.6.5.2.1.18 | TablemplsTunnelErrorTable | not-accessible | current | This table 'augments' the mplsTunnelTable. This table provides per-tunnel information about errors. Errors may be detected locally or reported through the sign… |
| 1.3.6.1.4.1.738.1.6.5.2.1.18.1 | RowmplsTunnelErrorEntry | not-accessible | current | An entry in this table is created by the LSR for every tunnel where error information is visible to the LSR. Note that systems which read the objects in this t… |
| 1.3.6.1.4.1.738.1.6.5.2.1.18.1.1 | ColumnmplsTunnelErrorLastErrorType | read-only | current | The nature of the last error. Provides interpretation context for mplsTunnelErrorProtocolCode and mplsTunnelErrorProtocolSubcode. A value of noError (0) shows … |
| 1.3.6.1.4.1.738.1.6.5.2.1.18.1.2 | ColumnmplsTunnelErrorLastTime | read-only | current | The time at which the last error occurred. This is presented as the value of SysUpTime when the error occurred or was reported to this node. If mplsTunnelError… |
| 1.3.6.1.4.1.738.1.6.5.2.1.18.1.3 | ColumnmplsTunnelErrorReporterType | read-only | current | The address type of the error reported. This object is used to aid in interpretation of mplsTunnelErrorReporter. |
| 1.3.6.1.4.1.738.1.6.5.2.1.18.1.4 | ColumnmplsTunnelErrorReporter | read-only | current | The address of the node reporting the last error, or the address of the resource (such as an interface) associated with the error. If mplsTunnelErrorLastErrorT… |
| 1.3.6.1.4.1.738.1.6.5.2.1.18.1.5 | ColumnmplsTunnelErrorCode | read-only | current | The primary error code associated with the last error. The interpretation of this error code depends on the value of mplsTunnelErrorLastErrorType. If the value… |
| 1.3.6.1.4.1.738.1.6.5.2.1.18.1.6 | ColumnmplsTunnelErrorSubcode | read-only | current | The secondary error code associated with the last error and the protocol used to signal this tunnel. This value is interpreted in the context of the value of m… |
| 1.3.6.1.4.1.738.1.6.5.2.1.18.1.7 | ColumnmplsTunnelErrorTLVs | read-only | current | The sequence of interface identifier TLVs reported with the error by the protocol code. The interpretation of the TLVs and the encoding within the protocol are… |
| 1.3.6.1.4.1.738.1.6.5.2.1.18.1.8 | ColumnmplsTunnelErrorHelpString | read-only | current | A textual string containing information about the last error, recovery actions and support advice. If there is no help string this object contains a zero lengt… |
| 1.3.6.1.4.1.738.1.6.5.2.1.19 | ScalarmplsTunnelHoldTimer | read-write | current | Defines a period in seconds needed to wait before rebuilding backup or primary tunnels if a frr condition occurs Currently no more than 10 seconds are allowed |
| 1.3.6.1.4.1.738.1.6.5.2.2 | NodemplsTeNotifications | |||
| 1.3.6.1.4.1.738.1.6.5.2.2.0 | NodemplsTeNotifyPrefix | |||
| 1.3.6.1.4.1.738.1.6.5.2.2.0.1 | NotificationmplsTunnelUp | current | This notification is generated when a mplsTunnelOperStatus object for one of the configured tunnels is about to leave the down state and transition into some o… | |
| 1.3.6.1.4.1.738.1.6.5.2.2.0.2 | NotificationmplsTunnelDown | current | This notification is generated when a mplsTunnelOperStatus object for one of the configured tunnels is about to enter the down state from some other state (but… | |
| 1.3.6.1.4.1.738.1.6.5.2.2.0.3 | NotificationmplsTunnelRerouted | current | This notification is generated when a tunnel is rerouted. If the actual path is used, then this object MAY contain the new path for this tunnel some time after… | |
| 1.3.6.1.4.1.738.1.6.5.2.2.0.4 | NotificationmplsTunnelReoptimized | current | This notification is generated when a tunnel is reoptimized. If the mplsTunnelARHopTable is used, then this tunnel instance's entry in the mplsTunnelARHopTable… | |
| 1.3.6.1.4.1.738.1.6.5.2.3 | NodemplsTeConformance | |||
| 1.3.6.1.4.1.738.1.6.5.2.3.1 | NodemplsTeGroups | |||
| 1.3.6.1.4.1.738.1.6.5.2.3.1.1 | GroupmplsTunnelGroup | current | Necessary, but not sufficient, set of objects to implement tunnels. In addition, depending on the type of the tunnels supported (for example, manually configur… | |
| 1.3.6.1.4.1.738.1.6.5.2.3.1.2 | GroupmplsTunnelManualGroup | current | Object(s) needed to implement manually configured tunnels. | |
| 1.3.6.1.4.1.738.1.6.5.2.3.1.3 | GroupmplsTunnelSignaledGroup | current | Objects needed to implement signaled tunnels. | |
| 1.3.6.1.4.1.738.1.6.5.2.3.1.4 | GroupmplsTunnelScalarGroup | current | Scalar object needed to implement MPLS tunnels. | |
| 1.3.6.1.4.1.738.1.6.5.2.3.1.5 | GroupmplsTunnelIsIntfcGroup | current | Objects needed to implement tunnels that are interfaces. | |
| 1.3.6.1.4.1.738.1.6.5.2.3.1.6 | GroupmplsTunnelIsNotIntfcGroup | current | Objects needed to implement tunnels that are not interfaces. | |
| 1.3.6.1.4.1.738.1.6.5.2.3.1.7 | GroupmplsTunnelCRLDPResOptionalGroup | current | Set of objects implemented for resources applicable for tunnels signaled using CR-LDP. | |
| 1.3.6.1.4.1.738.1.6.5.2.3.1.8 | GroupmplsTunnelSonetGroup | current | Set of objects needed to implement Sonet. None of these objects are mandatory. | |
| 1.3.6.1.4.1.738.1.6.5.2.3.1.9 | GroupmplsTunnelUniGroup | current | Set of objects needed to implement UNI. None of these objects are mandatory. | |
| 1.3.6.1.4.1.738.1.6.5.2.3.1.11 | GroupmplsTunnelBackupGroup | current | Set of objects needed for backup tunnels. None of these objects are mandatory. | |
| 1.3.6.1.4.1.738.1.6.5.2.3.1.12 | GroupmplsTunnelARHopGroup | current | Set of objects relating to ARHop. None of these objects are mandatory. | |
| 1.3.6.1.4.1.738.1.6.5.2.3.1.13 | GroupmplsTunnelCHopGroup | current | Set of objects relating to CHop. None of these objects are mandatory. | |
| 1.3.6.1.4.1.738.1.6.5.2.3.1.14 | GroupmplsDiffServGroup | current | Set of objects relating to DiffServ. None of these objects are mandatory. | |
| 1.3.6.1.4.1.738.1.6.5.2.3.1.15 | GroupmplsTeNotificationGroup | current | Set of notifications implemented in this module. None is mandatory. | |
| 1.3.6.1.4.1.738.1.6.5.2.3.2 | NodemplsTeCompliances | |||
| 1.3.6.1.4.1.738.1.6.5.2.3.2.1 | CompliancemplsTeModuleFullCompliance | current | Compliance statement for agents that provide full support the MPLS-TE-STD-MIB module. | |
| 1.3.6.1.4.1.738.1.6.5.2.3.2.2 | CompliancemplsTeModuleReadOnlyCompliance | read-only | current | Compliance requirement for implementations that only provide read-only support for MPLS-TE-STD-MIB. Such devices can then be monitored but cannot be configured… |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| MplsGeneralizedLabel | OCTET STRING (SIZE (0..255)) | current | This value represents a generalized MPLS Label. The label contents are specific to the label being represented. Wherever an MplsGeneralizedLabel is copied to or from a signaling protocol message, it is copied byte for b… |
| MplsGeneralizedLabelType | INTEGER { mplsLabel(1), generalizedLabel(2), wavebandLabel(3) } | current | The label types that are defined for Generalized MPLS. |
| MplsLsrId | Unsigned32 | current | A unique identifier for an MPLS LSR. This MAY represent an IpV4 address. |
| MplsTunnelIndexSyntax | Integer32 (0..65535) | current | Index into mplsTunnelTable. |
| MplsTunnelPrivateDataSyntax | OCTET STRING (SIZE (0..8)) | current | Represents private data field. |
| MplsTunnelTNAAddress | OCTET STRING (SIZE (0..20)) | current | TNA address of a tunnel. |