PW-CEP-STD-MIB
144 objects
This MIB module contains managed object definitions for Circuit Emulation over Packet (CEP) as in [RFC4842]: Malis, A., Prayson, P., Cohen, R., and D. Zelig. 'Synchronous Optical Network/Synchronous Digital Hierarchy (SONET/SDH) Circuit Emulation over Packet (CEP)', RFC 4842. Copyright (c) 2011 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info).
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.200 | IdentitypwCepStdMIB | This MIB module contains managed object definitions for Circuit Emulation over Packet (CEP) as in [RFC4842]: Malis, A., Prayson, P., Cohen, R., and D. Zelig. '… | ||
| 1.3.6.1.2.1.200.1 | NodepwCepObjects | |||
| 1.3.6.1.2.1.200.1.1 | TablepwCepTable | not-accessible | current | This table contains objects and parameters for managing and monitoring the CEP PW. |
| 1.3.6.1.2.1.200.1.1.1 | RowpwCepEntry | not-accessible | current | Each entry represents the association of a SONET/SDH path or VT to a PW. This table is indexed by the pwIndex of the applicable PW entry in the pwTable. An ent… |
| 1.3.6.1.2.1.200.1.1.1.1 | ColumnpwCepType | read-write | current | Specifies the sub-type of CEP PW. Currently only structured types are supported: 'spe'(1) : SONET STS-Nc signals. 'vt' (2) : SONET VT-x (x=1.5,2,3,6) signals. … |
| 1.3.6.1.2.1.200.1.1.1.2 | ColumnpwCepSonetIfIndex | read-write | current | This is a unique index within the ifTable. It represents the interface index for the SONET path for SPE emulation ([RFC3592], Section 3.3), an interface index … |
| 1.3.6.1.2.1.200.1.1.1.3 | ColumnpwCepSonetConfigErrorOrStatus | read-only | current | This object reports a configuration mismatch inside the local node or between the local node and the peer node. Some bits indicate an error, and some are simpl… |
| 1.3.6.1.2.1.200.1.1.1.4 | ColumnpwCepCfgIndex | read-write | current | Index to CEP configuration table below. Multiple CEP PWs MAY share a single pwCepCfgEntry. The value 0 indicates that no entries are available. |
| 1.3.6.1.2.1.200.1.1.1.5 | ColumnpwCepTimeElapsed | read-only | current | The number of seconds, including partial seconds, that have elapsed since the beginning of the current measurement period. If, for some reason such as an adjus… |
| 1.3.6.1.2.1.200.1.1.1.6 | ColumnpwCepValidIntervals | read-only | current | The number (n) of previous 15-minute intervals for which data was collected. An agent with CEP capability MUST be capable of supporting at least 4 intervals. T… |
| 1.3.6.1.2.1.200.1.1.1.7 | ColumnpwCepIndications | read-write | current | Definitions: 'missingPkt'(0) - While playing out a sequence of packets, at least one packet was determined to be missing based on a gap in the CEP sequence num… |
| 1.3.6.1.2.1.200.1.1.1.8 | ColumnpwCepLastEsTimeStamp | read-only | current | The value of sysUpTime on the most recent occasion at which the CEP PW entered the Errored Seconds (ES) or Severely Errored Seconds (SES) state. |
| 1.3.6.1.2.1.200.1.1.1.9 | ColumnpwCepPeerCepOption | read-only | current | The value of the CEP option parameter as received from the peer by the PW signaling protocol. |
| 1.3.6.1.2.1.200.1.2 | ScalarpwCepCfgIndexNext | read-only | current | This object contains an appropriate value to be used for pwCepCfgIndex when creating entries in the pwCepCfgTable. The value 0 indicates that no unassigned ent… |
| 1.3.6.1.2.1.200.1.3 | TablepwCepCfgTable | not-accessible | current | This table contains a set of parameters that may be referenced by one or more CEP PWs by pwCepTable. |
| 1.3.6.1.2.1.200.1.3.1 | RowpwCepCfgEntry | not-accessible | current | These parameters define the characteristics of a CEP PW. They are grouped here to ease Network Management System (NMS) burden. Once an entry is created here, i… |
| 1.3.6.1.2.1.200.1.3.1.1 | ColumnpwCepCfgTableIndex | not-accessible | current | Primary index to this table. |
| 1.3.6.1.2.1.200.1.3.1.2 | ColumnpwCepSonetPayloadLength | read-create | current | The number of SONET bytes of the Path or VT carried as payload within one packet. For example, for STS-1/VC-3 SPE circuits, a value of 783 bytes indicates that… |
| 1.3.6.1.2.1.200.1.3.1.3 | ColumnpwCepCfgMinPktLength | read-create | current | This object defines the minimum CEP packet length in number of bytes (including CEP header and payload). It applies to CEP's bandwidth-savings packets. Current… |
| 1.3.6.1.2.1.200.1.3.1.4 | ColumnpwCepCfgPktReorder | read-only | current | This object defines if reordering is applied for incoming packets. If set 'true', as inbound packets are queued in the jitter buffer, out-of-order packets are … |
| 1.3.6.1.2.1.200.1.3.1.5 | ColumnpwCepCfgEnableDBA | read-create | current | This object defines when DBA is applied for packets sent toward the PSN. Setting 'ais' MUST cause CEP packet payload suppression when AIS is detected on the as… |
| 1.3.6.1.2.1.200.1.3.1.6 | ColumnpwCepCfgRtpHdrSuppress | read-create | current | If this object is set to 'true', an RTP header is not prepended to the CEP packet. |
| 1.3.6.1.2.1.200.1.3.1.7 | ColumnpwCepCfgJtrBfrDepth | read-create | current | This object defines the number of microseconds of expected packet delay variation for this CEP PW over the PSN. The actual jitter buffer MUST be at least twice… |
| 1.3.6.1.2.1.200.1.3.1.8 | ColumnpwCepCfgConsecPktsInsync | read-create | current | Consecutive packets with sequential sequence numbers required to exit the LOPS state. |
| 1.3.6.1.2.1.200.1.3.1.9 | ColumnpwCepCfgConsecMissingOutSync | read-create | current | Consecutive missing packets required to enter the LOPS state. |
| 1.3.6.1.2.1.200.1.3.1.10 | ColumnpwCepCfgPktErrorPlayOutValue | read-create | current | This object defines the value played when inbound packets have over/underflowed the jitter buffer or are missing for any reason. This byte pattern is sent (pla… |
| 1.3.6.1.2.1.200.1.3.1.11 | ColumnpwCepCfgMissingPktsToSes | read-create | current | The number of missing packets detected (consecutive or not) within a 1-second window to cause a Severely Errored Second (SES) to be counted. |
| 1.3.6.1.2.1.200.1.3.1.12 | ColumnpwCepCfgSesToUas | read-create | current | The number of consecutive SESs before declaring PW in Unavailable Seconds (UAS) state (at which point pwCepPerfUASs starts counting). The SesToUas default valu… |
| 1.3.6.1.2.1.200.1.3.1.13 | ColumnpwCepCfgSecsToExitUas | read-create | current | The number of consecutive nonSESs before declaring PW is NOT in UAS state (at which point pwCepPerfUASs stops counting). |
| 1.3.6.1.2.1.200.1.3.1.14 | ColumnpwCepCfgName | read-create | current | This variable contains the name of the Configuration entry. This name may be used to help the NMS to display the purpose of the entry. |
| 1.3.6.1.2.1.200.1.3.1.15 | ColumnpwCepCfgRowStatus | read-create | current | For creating, modifying, and deleting this row. None of the read-create objects' values can be changed when pwCepCfgRowStatus is in the active(1) state. Change… |
| 1.3.6.1.2.1.200.1.3.1.16 | ColumnpwCepCfgStorageType | read-create | current | This object indicates the storage type for this row. |
| 1.3.6.1.2.1.200.1.4 | TablepwCepFracTable | not-accessible | current | This table contains a set of parameters for CEP PWs with pwCepType FRAC type. |
| 1.3.6.1.2.1.200.1.4.1 | RowpwCepFracEntry | not-accessible | current | There are two options for creating an entry in this table: - By the Element Management System (EMS) in advance for creating the PW. - By the agent automaticall… |
| 1.3.6.1.2.1.200.1.4.1.1 | ColumnpwCepFracIndex | not-accessible | current | This is the index of this table. It is a unique index within the ifTable. It represents the interface index for the SONET path ([RFC3592], Section 3.3) for fra… |
| 1.3.6.1.2.1.200.1.4.1.2 | ColumnpwCepFracMode | read-create | current | Fractional mode for STS-1/VC-3 or VC-4 circuits: notApplicable - When this object is not applicable. dynamic - EBM carried within the CEP header. Unequipped VT… |
| 1.3.6.1.2.1.200.1.4.1.3 | ColumnpwCepFracConfigError | read-only | current | vtgMapEbmConflict(1) is set when the configured static EBM does not match the configured vtgMap for fractional STS-1/VC-3 circuits or when the TUG2Map is in co… |
| 1.3.6.1.2.1.200.1.4.1.4 | ColumnpwCepFracAsync | read-create | current | This object defines the asynchronous payload carried within the STS-1/VC-3. This object is applicable when pwCepFracMode equals 'staticAsync' and MUST equal to… |
| 1.3.6.1.2.1.200.1.4.1.5 | ColumnpwCepFracVtgMap | read-create | current | This object defines the VT/VC types of the seven VTG/TUG-2 within the STS-1/VC-3. This variable should be set when 'dynamic', 'static', or 'staticWithEbm' frac… |
| 1.3.6.1.2.1.200.1.4.1.6 | ColumnpwCepFracEbm | read-create | current | This object holds the static Equipped Bit Mask (EBM) for STS-1/VC-3 channel. This variable MAY be set when 'static' or 'staticWithEbm' fractional STS-1/VC-3 pw… |
| 1.3.6.1.2.1.200.1.4.1.7 | ColumnpwCepFracPeerEbm | read-only | current | This object reports the Equipped Bit Mask (EBM) for STS-1/VC-3 channel as received from the peer within the CEP extension header. |
| 1.3.6.1.2.1.200.1.4.1.8 | ColumnpwCepFracSdhVc4Mode | read-create | current | Fractional mode for VC-4 circuits: notApplicable - When this is not VC-4 circuit. dynamic - EBM carried within the CEP header. Unequipped VTs are removed from … |
| 1.3.6.1.2.1.200.1.4.1.9 | ColumnpwCepFracSdhVc4Tu3Map1 | read-create | current | The type of asynchronous mapping carried inside STS-1, VC-3, or TUG-3 containing TU-3 circuit. |
| 1.3.6.1.2.1.200.1.4.1.10 | ColumnpwCepFracSdhVc4Tu3Map2 | read-create | current | If the second TUG-3 within the VC-4 contains a TU-3, this variable must be set. |
| 1.3.6.1.2.1.200.1.4.1.11 | ColumnpwCepFracSdhVc4Tu3Map3 | read-create | current | If the third TUG-3 within the VC-4 contains a TU-3, this variable must be set. |
| 1.3.6.1.2.1.200.1.4.1.12 | ColumnpwCepFracSdhVc4Tug2Map1 | read-create | current | The VC types of the seven TUG-2s within the first TUG-3 of the VC-4. |
| 1.3.6.1.2.1.200.1.4.1.13 | ColumnpwCepFracSdhVc4Tug2Map2 | read-create | current | The VC types of the seven TUG-2s within the second TUG-3 of the VC-4. |
| 1.3.6.1.2.1.200.1.4.1.14 | ColumnpwCepFracSdhVc4Tug2Map3 | read-create | current | The VC types of the seven TUG-2s within the third TUG-3 of the VC-4. |
| 1.3.6.1.2.1.200.1.4.1.15 | ColumnpwCepFracSdhVc4Ebm1 | read-create | current | Static Equipped Bit Mask (EBM) for the first TUG-3 within the VC-4. This variable should be set when 'static' or 'staticWithEbm' fractional VC-4 pwCepFracMode … |
| 1.3.6.1.2.1.200.1.4.1.16 | ColumnpwCepFracSdhVc4Ebm2 | read-create | current | Static Equipped Bit Mask (EBM) for the second TUG-3 within the VC-4. This variable should be set when 'static' or 'staticWithEbm' fractional VC-4 pwCepFracMode… |
| 1.3.6.1.2.1.200.1.4.1.17 | ColumnpwCepFracSdhVc4Ebm3 | read-create | current | Static Equipped Bit Mask (EBM) for the third TUG-3 within the VC-4. This variable should be set when 'Static' or 'staticWithEbm' fractional VC-4 pwCepFracMode … |
| 1.3.6.1.2.1.200.1.4.1.18 | ColumnpwCepFracSdhVc4PeerEbm1 | read-only | current | Equipped Bit Mask (EBM) for the first TUG-3 within the fractional VC-4 channel received from the peer within the CEP extension header. |
| 1.3.6.1.2.1.200.1.4.1.19 | ColumnpwCepFracSdhVc4PeerEbm2 | read-only | current | Equipped Bit Mask (EBM) for the second TUG-3 within the fractional VC-4 channel received from the peer within the CEP extension header. |
| 1.3.6.1.2.1.200.1.4.1.20 | ColumnpwCepFracSdhVc4PeerEbm3 | read-only | current | Equipped Bit Mask (EBM) for the third TUG-3 within the fractional VC-4 channel received from the peer within the CEP extension header. |
| 1.3.6.1.2.1.200.1.4.1.21 | ColumnpwCepFracRowStatus | read-create | current | For creating, modifying, and deleting this row. This object MAY be changed at any time. |
| 1.3.6.1.2.1.200.1.4.1.22 | ColumnpwCepFracStorageType | read-create | current | This variable indicates the storage type for this object. |
| 1.3.6.1.2.1.200.1.5 | TablepwCepPerfCurrentTable | not-accessible | current | CEP bridges the SONET and packet worlds. In the packet world, counts typically start from the time of service creation and do not stop. In the SONET world, cou… |
| 1.3.6.1.2.1.200.1.5.1 | RowpwCepPerfCurrentEntry | not-accessible | current | An entry in this table is created by the agent for every pwCep entry. After 15 minutes, the contents of this table entry are copied to a new entry in the pwCep… |
| 1.3.6.1.2.1.200.1.5.1.1 | ColumnpwCepPerfCurrentDbaInPacketsHC | read-only | current | Number of DBA packets received. |
| 1.3.6.1.2.1.200.1.5.1.2 | ColumnpwCepPerfCurrentDbaOutPacketsHC | read-only | current | Number of DBA packets sent. |
| 1.3.6.1.2.1.200.1.5.1.3 | ColumnpwCepPerfCurrentInNegPtrAdjust | read-only | current | Number of negative pointer adjustments sent on the SONET path based on CEP pointer adjustments received. |
| 1.3.6.1.2.1.200.1.5.1.4 | ColumnpwCepPerfCurrentInPosPtrAdjust | read-only | current | Number of positive pointer adjustments sent on the SONET path based on CEP pointer adjustments received. |
| 1.3.6.1.2.1.200.1.5.1.5 | ColumnpwCepPerfCurrentInPtrAdjustSecs | read-only | current | Number of seconds in which a positive or negative pointer adjustment was sent on the SONET path. |
| 1.3.6.1.2.1.200.1.5.1.6 | ColumnpwCepPerfCurrentOutNegPtrAdjust | read-only | current | Number of negative pointer adjustments seen on the SONET path and encoded onto sent CEP packets. |
| 1.3.6.1.2.1.200.1.5.1.7 | ColumnpwCepPerfCurrentOutPosPtrAdjust | read-only | current | Number of positive pointer adjustments seen on the SONET path and encoded onto sent CEP packets. |
| 1.3.6.1.2.1.200.1.5.1.8 | ColumnpwCepPerfCurrentOutPtrAdjustSecs | read-only | current | Number of seconds in which a positive or negative pointer adjustment was seen on the SONET path. |
| 1.3.6.1.2.1.200.1.5.1.9 | ColumnpwCepPerfCurrentAbsPtrAdjust | read-only | current | Indicates the relative adjustment drift between inbound and outbound streams. It is calculated as absolute value of: (InPosPtrAdjust - InNegPtrAdjust ) - (OutP… |
| 1.3.6.1.2.1.200.1.5.1.10 | ColumnpwCepPerfCurrentMissingPkts | read-only | current | Number of missing packets (as detected via CEP header sequence number gaps). |
| 1.3.6.1.2.1.200.1.5.1.11 | ColumnpwCepPerfCurrentPktsOoseq | read-only | current | Number of packets detected out of sequence (via CEP header sequence numbers) but successfully reordered. Note: Some implementations may not support this featur… |
| 1.3.6.1.2.1.200.1.5.1.12 | ColumnpwCepPerfCurrentPktsOoRngDropped | read-only | current | Number of packets detected out of range (via CEP header sequence numbers) and could not be reordered or could not fit in the jitter buffer. |
| 1.3.6.1.2.1.200.1.5.1.13 | ColumnpwCepPerfCurrentJtrBfrUnderruns | read-only | current | Number of times a packet needed to be played out and the jitter buffer was empty. |
| 1.3.6.1.2.1.200.1.5.1.14 | ColumnpwCepPerfCurrentPktsMalformed | read-only | current | Number of packets detected with unexpected size or bad headers stack. |
| 1.3.6.1.2.1.200.1.5.1.15 | ColumnpwCepPerfCurrentSummaryErrors | read-only | current | A summary of all the packet-error types above (from missing packets to bad length packets). |
| 1.3.6.1.2.1.200.1.5.1.16 | ColumnpwCepPerfCurrentESs | read-only | current | The counter associated with the number of Errored Seconds encountered. |
| 1.3.6.1.2.1.200.1.5.1.17 | ColumnpwCepPerfCurrentSESs | read-only | current | The counter associated with the number of Severely Errored Seconds encountered. |
| 1.3.6.1.2.1.200.1.5.1.18 | ColumnpwCepPerfCurrentUASs | read-only | current | The counter associated with the number of Unavailable Seconds encountered. |
| 1.3.6.1.2.1.200.1.5.1.19 | ColumnpwCepPerfCurrentFC | read-only | current | CEP Failure Counts (FC-CEP). The number of CEP failure events. A failure event begins when the LOPS failure is declared and ends when the failure is cleared. A… |
| 1.3.6.1.2.1.200.1.6 | TablepwCepPerfIntervalTable | not-accessible | current | This table provides per-CEP PW performance information, much like the pwCepPerfCurrentTable above. However, these counts represent historical 15-minute interva… |
| 1.3.6.1.2.1.200.1.6.1 | RowpwCepPerfIntervalEntry | not-accessible | current | An entry in this table is created by the agent for every pwCepPerfCurrentEntry that is 15 minutes old. The contents of the Current entry are copied to the new … |
| 1.3.6.1.2.1.200.1.6.1.1 | ColumnpwCepPerfIntervalNumber | not-accessible | current | A number (between 1 and 96 to cover a 24-hour period) that identifies the interval for which the set of statistics is available. The interval identified by 1 i… |
| 1.3.6.1.2.1.200.1.6.1.2 | ColumnpwCepPerfIntervalValidData | read-only | current | This variable indicates if the data for this interval is valid. |
| 1.3.6.1.2.1.200.1.6.1.3 | ColumnpwCepPerfIntervalReset | read-create | current | Used in cases where the user knows that the errors within this interval should not be counted. Writing 'reset' sets all error counts to zero. The value of 0 is… |
| 1.3.6.1.2.1.200.1.6.1.4 | ColumnpwCepPerfIntervalTimeElapsed | read-only | current | The duration of a particular interval in seconds. Adjustments in the system's time-of-day clock may cause the interval to be greater or less than the normal va… |
| 1.3.6.1.2.1.200.1.6.1.5 | ColumnpwCepPerfIntervalDbaInPacketsHC | read-only | current | Number of DBA packets received. |
| 1.3.6.1.2.1.200.1.6.1.6 | ColumnpwCepPerfIntervalDbaOutPacketsHC | read-only | current | Number of DBA packets sent. |
| 1.3.6.1.2.1.200.1.6.1.7 | ColumnpwCepPerfIntervalInNegPtrAdjust | read-only | current | Number of negative pointer adjustments sent on the SONET path based on CEP pointer adjustments received. |
| 1.3.6.1.2.1.200.1.6.1.8 | ColumnpwCepPerfIntervalInPosPtrAdjust | read-only | current | Number of positive pointer adjustments sent on the SONET path based on CEP pointer adjustments received. |
| 1.3.6.1.2.1.200.1.6.1.9 | ColumnpwCepPerfIntervalInPtrAdjustSecs | read-only | current | Number of seconds in which a positive or negative pointer adjustment was sent on the SONET path. |
| 1.3.6.1.2.1.200.1.6.1.10 | ColumnpwCepPerfIntervalOutNegPtrAdjust | read-only | current | Number of negative pointer adjustments seen on the SONET path and encoded onto sent CEP packets. |
| 1.3.6.1.2.1.200.1.6.1.11 | ColumnpwCepPerfIntervalOutPosPtrAdjust | read-only | current | Number of positive pointer adjustments seen on the SONET path and encoded onto sent CEP packets. |
| 1.3.6.1.2.1.200.1.6.1.12 | ColumnpwCepPerfIntervalOutPtrAdjustSecs | read-only | current | Number of seconds in which a positive or negative pointer adjustment was seen on the SONET path. |
| 1.3.6.1.2.1.200.1.6.1.13 | ColumnpwCepPerfIntervalAbsPtrAdjust | read-only | current | The relative adjustment drift between inbound and outbound streams. It is calculated as absolute value of: (InPosPtrAdjust - InNegPtrAdjust) - (OutPosPtrAdjust… |
| 1.3.6.1.2.1.200.1.6.1.14 | ColumnpwCepPerfIntervalMissingPkts | read-only | current | Number of missing packets (as detected via CEP header sequence number gaps). |
| 1.3.6.1.2.1.200.1.6.1.15 | ColumnpwCepPerfIntervalPktsOoseq | read-only | current | Number of packets detected out of sequence (via CEP header sequence numbers) but successfully reordered. Note: Some implementations mat not support this featur… |
| 1.3.6.1.2.1.200.1.6.1.16 | ColumnpwCepPerfIntervalPktsOoRngDropped | read-only | current | Number of packets detected out of range (via CEP header sequence numbers) and could not be reordered or could not fit in the jitter buffer. |
| 1.3.6.1.2.1.200.1.6.1.17 | ColumnpwCepPerfIntervalJtrBfrUnderruns | read-only | current | Number of times a packet needed to be played out and the jitter buffer was empty. |
| 1.3.6.1.2.1.200.1.6.1.18 | ColumnpwCepPerfIntervalPktsMalformed | read-only | current | Number of packets detected with unexpected size or bad headers stack. |
| 1.3.6.1.2.1.200.1.6.1.19 | ColumnpwCepPerfIntervalSummaryErrors | read-only | current | A summary of all the packet-error types above (from missing packets to bad length packets). |
| 1.3.6.1.2.1.200.1.6.1.20 | ColumnpwCepPerfIntervalESs | read-only | current | The counter associated with the number of Errored Seconds encountered. |
| 1.3.6.1.2.1.200.1.6.1.21 | ColumnpwCepPerfIntervalSESs | read-only | current | The counter associated with the number of Severely Errored Seconds encountered. |
| 1.3.6.1.2.1.200.1.6.1.22 | ColumnpwCepPerfIntervalUASs | read-only | current | The counter associated with the number of Unavailable Seconds encountered. |
| 1.3.6.1.2.1.200.1.6.1.23 | ColumnpwCepPerfIntervalFC | read-only | current | CEP Failure Counts (FC-CEP). The number of CEP failure events. A failure event begins when the LOPS failure is declared and ends when the failure is cleared. A… |
| 1.3.6.1.2.1.200.1.7 | TablepwCepPerf1DayIntervalTable | not-accessible | current | This table provides per CEP PW performance information, the current day's measurement, and the previous day's interval. In the extreme case where one of the er… |
| 1.3.6.1.2.1.200.1.7.1 | RowpwCepPerf1DayIntervalEntry | not-accessible | current | An entry is created in this table by the agent for every entry in the pwCepTable and for each day interval up to the number of supported historical intervals. |
| 1.3.6.1.2.1.200.1.7.1.1 | ColumnpwCepPerf1DayIntervalNumber | not-accessible | current | History Data Interval number. Interval 1 is the current day measurement period; interval 2 is the most recent previous day; and interval 30 is 31 days ago. |
| 1.3.6.1.2.1.200.1.7.1.2 | ColumnpwCepPerf1DayIntervalValidData | read-only | current | This variable indicates if the data for this interval is valid. |
| 1.3.6.1.2.1.200.1.7.1.3 | ColumnpwCepPerf1DayIntervalMoniSecs | read-only | current | The amount of time in the 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval dur… |
| 1.3.6.1.2.1.200.1.7.1.4 | ColumnpwCepPerf1DayIntervalDbaInPacketsHC | read-only | current | Number of DBA packets received. |
| 1.3.6.1.2.1.200.1.7.1.5 | ColumnpwCepPerf1DayIntervalDbaOutPacketsHC | read-only | current | Number of DBA packets sent. |
| 1.3.6.1.2.1.200.1.7.1.6 | ColumnpwCepPerf1DayIntervalInNegPtrAdjust | read-only | current | Number of negative pointer adjustments sent on the SONET path based on CEP pointer adjustments received. |
| 1.3.6.1.2.1.200.1.7.1.7 | ColumnpwCepPerf1DayIntervalInPosPtrAdjust | read-only | current | Number of positive pointer adjustments sent on the SONET path based on CEP pointer adjustments received. |
| 1.3.6.1.2.1.200.1.7.1.8 | ColumnpwCepPerf1DayIntervalInPtrAdjustSecs | read-only | current | Number of seconds in which a positive or negative pointer adjustment was sent on the SONET path. |
| 1.3.6.1.2.1.200.1.7.1.9 | ColumnpwCepPerf1DayIntervalOutNegPtrAdjust | read-only | current | Number of negative pointer adjustments seen on the SONET path and encoded onto sent CEP packets. |
| 1.3.6.1.2.1.200.1.7.1.10 | ColumnpwCepPerf1DayIntervalOutPosPtrAdjust | read-only | current | Number of positive pointer adjustments seen on the SONET path and encoded onto sent CEP packets. |
| 1.3.6.1.2.1.200.1.7.1.11 | ColumnpwCepPerf1DayIntervalOutPtrAdjustSecs | read-only | current | Number of seconds in which a positive or negative pointer adjustment was seen on the SONET path. |
| 1.3.6.1.2.1.200.1.7.1.12 | ColumnpwCepPerf1DayIntervalAbsPtrAdjust | read-only | current | The relative adjustment of drift between inbound and outbound streams. It is calculated as absolute value of: (InPosPtrAdjust - InNegPtrAdjust) - (OutPosPtrAdj… |
| 1.3.6.1.2.1.200.1.7.1.13 | ColumnpwCepPerf1DayIntervalMissingPkts | read-only | current | Number of missing packets (as detected via CEP header sequence number gaps). |
| 1.3.6.1.2.1.200.1.7.1.14 | ColumnpwCepPerf1DayIntervalPktsOoseq | read-only | current | Number of packets detected out of sequence (via CEP header sequence numbers) but successfully reordered. Note: Some implementations may not support this featur… |
| 1.3.6.1.2.1.200.1.7.1.15 | ColumnpwCepPerf1DayIntervalPktsOoRngDropped | read-only | current | Number of packets detected out of range (via CEP header sequence numbers) and could not be reordered or could not fit in the jitter buffer. |
| 1.3.6.1.2.1.200.1.7.1.16 | ColumnpwCepPerf1DayIntervalJtrBfrUnderruns | read-only | current | Number of times a packet needed to be played out, and the jitter buffer was empty. |
| 1.3.6.1.2.1.200.1.7.1.17 | ColumnpwCepPerf1DayIntervalPktsMalformed | read-only | current | Number of packets detected with unexpected size or bad headers stack. |
| 1.3.6.1.2.1.200.1.7.1.18 | ColumnpwCepPerf1DayIntervalSummaryErrors | read-only | current | A summary of all the packet-error types above (from missing packets to bad length packets). |
| 1.3.6.1.2.1.200.1.7.1.19 | ColumnpwCepPerf1DayIntervalESs | read-only | current | The counter associated with the number of Errored Seconds encountered. |
| 1.3.6.1.2.1.200.1.7.1.20 | ColumnpwCepPerf1DayIntervalSESs | read-only | current | The counter associated with the number of Severely Errored Seconds. See pwCepCfgMissingPktsToSes. |
| 1.3.6.1.2.1.200.1.7.1.21 | ColumnpwCepPerf1DayIntervalUASs | read-only | current | The counter associated with the number of unavailable seconds. See pwCepCfgSesToUAS. NOTE: When first entering the UAS state, the number of SesToUas is added t… |
| 1.3.6.1.2.1.200.1.7.1.22 | ColumnpwCepPerf1DayIntervalFC | read-only | current | CEP Failure Counts (FC-CEP). The number of CEP failure events. A failure event begins when the LOPS failure is declared and ends when the failure is cleared. |
| 1.3.6.1.2.1.200.2 | NodepwCepConformance | |||
| 1.3.6.1.2.1.200.2.1 | NodepwCepGroups | |||
| 1.3.6.1.2.1.200.2.1.1 | GrouppwCepGroup | current | Collection of objects for basic CEP PW config and status. | |
| 1.3.6.1.2.1.200.2.1.2 | GrouppwCepSignalingGroup | current | Collection of objects required if the network element support CEP connections signaling. | |
| 1.3.6.1.2.1.200.2.1.3 | GrouppwCepCfgGroup | current | Collection of detailed objects needed to configure CEP PWs. | |
| 1.3.6.1.2.1.200.2.1.4 | GrouppwCepPerfCurrentGroup | current | Collection of statistics objects for CEP PWs. | |
| 1.3.6.1.2.1.200.2.1.5 | GrouppwCepPerfIntervalGroup | current | Collection of statistics objects for CEP PWs. | |
| 1.3.6.1.2.1.200.2.1.6 | GrouppwCepPerf1DayIntervalGroup | current | Collection of statistics objects for CEP PWs. | |
| 1.3.6.1.2.1.200.2.1.7 | GrouppwCepFractionalGroup | current | Collection of fractional SPE objects. These objects are optional and should be supported only if fractional SPE is supported within the network element. | |
| 1.3.6.1.2.1.200.2.1.8 | GrouppwCepFractionalSts1Vc3Group | current | Collection of fractional STS-1/VC3 objects. These objects are optional and should be supported only if fractional STS-1/VC3 is supported within the network ele… | |
| 1.3.6.1.2.1.200.2.1.9 | GrouppwCepFractionalVc4Group | current | Collection of fractional VC4 objects. These objects are optional and should be supported only if fractional VC4 is supported within the network element. | |
| 1.3.6.1.2.1.200.2.2 | NodepwCepCompliances | |||
| 1.3.6.1.2.1.200.2.2.1 | CompliancepwCepModuleFullCompliance | read-only | current | The compliance statement for agents that support full CEP PW configuration through this MIB module. |
| 1.3.6.1.2.1.200.2.2.2 | CompliancepwCepModuleReadOnlyCompliance | read-only | current | The compliance statement for agents that provide read-only support for the PW CEP MIB Module. Such devices can be monitored but cannot be configured using this… |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| PwCepFracAsyncMap | INTEGER { other ( 1), ds3 ( 2), e3 ( 3) } | current | The type of asynchronous mapping carried inside STS-1, VC-3, or TUG-3 containing TU-3 circuit. |
| PwCepSdhVc4Ebm | Unsigned32 | current | Equipped Bit Mask (EBM) used for each Tributary Unit Group 3 (TUG-3) in fractional VC-4 circuits. The EBM bits are the 30 least significant bits out of the 32-bit value. |
| PwCepSonetEbm | Unsigned32 | current | Equipped Bit Mask (EBM) used for fractional STS-1/Virtual Circuit 3 (VC-3). The EBM bits are the 28 least significant bits out of the 32-bit value. |
| PwCepSonetVtgMap | Unsigned32 | current | The VT/VC types carried in the 7 VT groups (VTGs)/TUG-2s. The format is 28 bits in the form of an Equipped Bit Mask (EBM) for fractional STS-1/VC-3. The mapping specifies the maximal occupancies of VT/VC within each VTG… |