PW-TDM-R-MIB
89 objects
This MIB contains managed object definitions for encapsulating TDM (T1,E1, T3, E3, NxDS0) as pseudo-wires over packet-switching networks (PSN). This MIB supplements the PW-STD-MIB as in: Zelig, D., Nadeau,T. 'Pseudo Wire (PW) Management Information Base'. The PW-STD-MIB contains structures and MIB associations generic to Pseudo-Wire (PW) emulation. PW-specific MIBs (such as this) contain config and stats for specific PW types. Copyright (C) The IETF Trust (2007). This version of this MIB module is part of RFC yyyy; see the RFC itself for full legal notices. note
Imported Objects
| IF-MIB | InterfaceIndexOrZero |
| PerfHist-TC-MIB | PerfCurrentCount PerfIntervalCount |
| PW-STD-R-MIB | pwIndex |
| PW-TC-STD-R-MIB | PwCfgIndexOrzero |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Integer32 MODULE-IDENTITY OBJECT-TYPE transmission Unsigned32 |
| SNMPv2-TC | RowStatus StorageType TEXTUAL-CONVENTION TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.20 | NoderadExperimental | |||
| 1.20.13 | IdentitypwTDMMIBR | This MIB contains managed object definitions for encapsulating TDM (T1,E1, T3, E3, NxDS0) as pseudo-wires over packet-switching networks (PSN). This MIB supple… | ||
| 1.20.13.1 | NodepwTDMObjects | |||
| 1.20.13.1.1 | TablepwTDMTable | not-accessible | current | This table contains basic information including ifIndex, and pointers to entries in the relevant TDM config tables for this TDM PW. |
| 1.20.13.1.1.1 | RowpwTDMEntry | not-accessible | current | This table is indexed by the same index that was created for the associated entry in the PW Table (in the PW-STD-MIB). - The PwIndex. An entry is created in th… |
| 1.20.13.1.1.1.1 | ColumnpwTDMRate | read-write | current | The parameter represents the bit-rate of the TDM service in multiples of the 'basic' 64 Kbit/s rate [TDMCP-EXT]. It complements the definition of pwType used i… |
| 1.20.13.1.1.1.2 | ColumnpwTDMIfIndex | read-write | current | This is a unique index within the ifTable. It represents the interface index of the full link or the interface index for the bundle holding the group of time s… |
| 1.20.13.1.1.1.3 | ColumnpwGenTDMCfgIndex | read-write | current | Index to the generic parameters in the TDM configuration table that appears in this MIB module. It is likely that multiple TDM PWs of the same characteristic w… |
| 1.20.13.1.1.1.4 | ColumnpwRelTDMCfgIndex | read-write | current | Index to the relevant TDM configuration table entry that appears in one of the related MIB modules such as TDMoIP or CESoPSN. It is likely that multiple TDM PW… |
| 1.20.13.1.1.1.5 | ColumnpwTDMConfigError | read-only | current | Any of the bits are set if the local configuration is not compatible with the peer configuration as available from the various parameters options. Setting is d… |
| 1.20.13.1.1.1.6 | ColumnpwTDMTimeElapsed | read-only | current | The number of seconds, including partial seconds, that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adju… |
| 1.20.13.1.1.1.7 | ColumnpwTDMValidIntervals | read-only | current | The number of previous 15-minute intervals for which data was collected. An agent with TDM capability must be capable of supporting at least n intervals. The m… |
| 1.20.13.1.1.1.8 | ColumnpwTDMValidDayIntervals | read-only | current | The number of previous days for which data was collected. An agent with TDM capability must be capable of supporting at least n intervals. The minimum value of… |
| 1.20.13.1.1.1.9 | ColumnpwTDMCurrentIndications | read-only | deprecated | The following defects should be detected and reported upon request: -Stray packets MAY be detected by the PSN and multiplexing layers. Stray packets MUST be di… |
| 1.20.13.1.1.1.10 | ColumnpwTDMLatchedIndications | read-only | deprecated | The state of TDM indicators when the TDM PW last declared an error second (either as ES, SES or a second with errors inside a UAS) condition. At this time, onl… |
| 1.20.13.1.1.1.11 | ColumnpwTDMLastEsTimeStamp | read-only | current | The value of sysUpTime at the most recent occasion at which the TDM PW entered the ES or SES state. |
| 1.20.13.1.2 | ScalarpwTDMCfgIndexNext | read-only | current | This object contains the value to be used for pwTDMCfgIndex when creating entries in the pwTDMCfgTable. The value 0 indicates that no unassigned entries are av… |
| 1.20.13.1.3 | TablepwTDMCfgTable | not-accessible | current | This table contains a set of parameters that may be referenced by one or more TDM PWs in pwTDMTable. |
| 1.20.13.1.3.1 | RowpwTDMCfgEntry | not-accessible | current | These parameters define the characteristics of a TDM PW. They are grouped here to ease NMS burden. Once an entry is created here it may be re-used by many PWs.… |
| 1.20.13.1.3.1.1 | ColumnpwTDMCfgIndex | not-accessible | current | Index to an entry in this table. The value is a copy of the assigned pwTDMCfgIndexNext |
| 1.20.13.1.3.1.2 | ColumnpwTDMCfgRowStatus | read-create | current | Object used for creating, modifying, and deleting a row from this table. The following objects should not be modified if the entry is in used and the status is… |
| 1.20.13.1.3.1.3 | ColumnpwTDMCfgConfErr | read-only | deprecated | Various configuration errors. Illegal settings within the pwTDMCfg table. Setting is done based on signaling, or else value (0) will be set |
| 1.20.13.1.3.1.4 | ColumnpwTDMCfgPayloadSize | read-create | current | The value of this object indicates the PayLoad Size (in bytes) to be defined during the PW setUp. Upon TX, implementation must be capable of carrying that amou… |
| 1.20.13.1.3.1.5 | ColumnpwTDMCfgPktReorder | read-create | current | If set True: as CE bound packets are queued in the jitter buffer, out of order packets are re-ordered. The maximum sequence number differential (i.e., the rang… |
| 1.20.13.1.3.1.6 | ColumnpwTDMCfgRtpHdrUsed | read-create | current | If set to False: an RTP header is not pre-pended to the TDM packet. |
| 1.20.13.1.3.1.7 | ColumnpwTDMCfgJtrBfrDepth | read-create | current | The size of this buffer SHOULD be locally configured to allow accommodation to the PSN-specific packet delay variation. If configured to a value not supported … |
| 1.20.13.1.3.1.8 | ColumnpwTDMCfgPayloadSuppression | read-create | current | Selecting 'enable' means: Payload suppression is allowed. Payload MAY be omitted in order to conserve bandwidth. Selecting 'disable' means: no suppresion under… |
| 1.20.13.1.3.1.9 | ColumnpwTDMCfgConsecPktsInSynch | read-create | current | The number of consecutive packets with sequential sequence numbers that are required to exit the LOPS state. Object MAY be changed when the related PW is defin… |
| 1.20.13.1.3.1.10 | ColumnpwTDMCfgConsecMissPktsOutSynch | read-create | current | The number of consecutive missing packets that are required to enter the LOPS state. Object MAY be changed when the related PW is defined as not active. |
| 1.20.13.1.3.1.11 | ColumnpwTDMCfgSetUp2SynchTimeOut | read-create | current | The amount of time the host should wait before declaring the pseudo wire in down state, if the number of consecutive TDM packets that have been received after … |
| 1.20.13.1.3.1.12 | ColumnpwTDMCfgPktReplacePolicy | read-create | current | This parameter determines the value to be played when CE bound packets have over/underflow the jitter buffer, or are missing for any reason. This byte pattern … |
| 1.20.13.1.3.1.13 | ColumnpwTDMCfgAvePktLossTimeWindow | read-create | current | The length of time over which the average packet loss rate should be computed to detect Excessive packet loss rate. Object MAY be changed when the related PW i… |
| 1.20.13.1.3.1.14 | ColumnpwTDMCfgExcessivePktLossThreshold | read-create | current | Excessive packet loss rate is detected by computing the average packetloss rate over a pwTDMCfgAvePktLossTimeWindow amount of time and comparing it with this t… |
| 1.20.13.1.3.1.15 | ColumnpwTDMCfgAlarmThreshold | read-create | current | Alarms are only reported when the defect state persists for the length of time specified by this object. The object's unit is millisec. Object MAY be changed w… |
| 1.20.13.1.3.1.16 | ColumnpwTDMCfgClearAlarmThreshold | read-create | current | Alarm MUST be cleared after the corresponding defect is undetected for the amount of time specified by this object. The object's unit is millisec. Object MAY b… |
| 1.20.13.1.3.1.17 | ColumnpwTDMCfgMissingPktsToSes | read-create | current | Percent of missing packets detected (consecutive or not) within a 1 second window to cause a Severely Error Second (SES) to be counted. Object MAY be changed w… |
| 1.20.13.1.3.1.18 | ColumnpwTDMCfgTimestampMode | read-create | current | Timestamp generation MAY be used in one of the following modes: 1. Absolute mode: the PSN-bound IWF sets timestamps using the clock recovered from the incoming… |
| 1.20.13.1.3.1.19 | ColumnpwTDMCfgStorageType | read-create | current | This variable indicates the storage type for this row. |
| 1.20.13.1.3.1.20 | ColumnpwTDMCfgPktFiller | read-create | current | Filler byte pattern played out on the TDM interface if pwTDMCfgPktReplacePolicy was set to filler(3). Object MAY be changed when the related PW is defined as n… |
| 1.20.13.1.3.1.21 | ColumnpwTDMCfgName | read-create | current | A descriptive string, prefereably unique name, to an entry in this table. Object MAY be changed at any time. |
| 1.20.13.1.5 | TablepwTDMPerfCurrentTable | not-accessible | current | The current 15 minute interval counts are in this table. This table provides per TDM PW performance information. |
| 1.20.13.1.5.1 | RowpwTDMPerfCurrentEntry | not-accessible | current | An entry in this table is created by the agent for every pwTDMTable entry. After 15 minutes, the contents of this table entry are copied to a new entry in the … |
| 1.20.13.1.5.1.1 | ColumnpwTDMPerfCurrentMissingPkts | read-only | current | Number of missing packets (as detected via control word sequence number gaps). |
| 1.20.13.1.5.1.2 | ColumnpwTDMPerfCurrentPktsReOrder | read-only | current | Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this Fea… |
| 1.20.13.1.5.1.3 | ColumnpwTDMPerfCurrentJtrBfrUnderruns | read-only | current | Number of times a packet needed to be played out and the jitter buffer was empty. |
| 1.20.13.1.5.1.4 | ColumnpwTDMPerfCurrentMisOrderDropped | read-only | current | Number of packets detected out of order(via control word sequence numbers), and could not be re-ordered, or could not fit in the jitter buffer. |
| 1.20.13.1.5.1.5 | ColumnpwTDMPerfCurrentMalformedPkt | read-only | current | Number of packets detected with unexpected size, or bad headers' stack |
| 1.20.13.1.5.1.6 | ColumnpwTDMPerfCurrentESs | read-only | current | The counter associated with the number of Error Seconds encountered. Any malformed packet, seq. error, LOPS and similar are considered as error second |
| 1.20.13.1.5.1.7 | ColumnpwTDMPerfCurrentSESs | read-only | current | The counter associated with the number of Severely Error Seconds encountered. |
| 1.20.13.1.5.1.8 | ColumnpwTDMPerfCurrentUASs | read-only | current | The counter associated with the number of Unavailable Seconds encountered. Any consequtive ten seconds of SES are counted as one UAS |
| 1.20.13.1.5.1.9 | ColumnpwTDMPerfCurrentFC | read-only | current | TDM Failure Counts (FC-TDM). The number of TDM failure events. A failure event begins when the LOPS failure is declared, and ends when the failure is cleared. … |
| 1.20.13.1.6 | TablepwTDMPerfIntervalTable | not-accessible | current | This table provides performance information per TDM PW similar to the pwTDMPerfCurrentTable above. However, these counts represent historical 15 minute interva… |
| 1.20.13.1.6.1 | RowpwTDMPerfIntervalEntry | not-accessible | current | An entry in this table is created by the agent for every pwTDMPerfCurrentEntry that is 15 minutes old. The contents of the Current entry are copied to the new … |
| 1.20.13.1.6.1.1 | ColumnpwTDMPerfIntervalNumber | not-accessible | current | A number (normally between 1 and 96 to cover a 24 hour period) which identifies the interval for which the set of statistics is available. The interval identif… |
| 1.20.13.1.6.1.2 | ColumnpwTDMPerfIntervalValidData | read-only | current | This variable indicates if the data for this interval is valid. |
| 1.20.13.1.6.1.3 | ColumnpwTDMPerfIntervalDuration | read-only | current | The duration of a particular interval in seconds, Adjustments in the system's time-of-day clock, may cause the interval to be greater or less than, the normal … |
| 1.20.13.1.6.1.4 | ColumnpwTDMPerfIntervalMissingPkts | read-only | current | Number of missing packets (as detected via control word sequence number gaps). |
| 1.20.13.1.6.1.5 | ColumnpwTDMPerfIntervalPktsReOrder | read-only | current | Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this Fea… |
| 1.20.13.1.6.1.6 | ColumnpwTDMPerfIntervalJtrBfrUnderruns | read-only | current | Number of times a packet needed to be played out and the jitter buffer was empty. |
| 1.20.13.1.6.1.7 | ColumnpwTDMPerfIntervalMisOrderDropped | read-only | current | Number of packets detected out of order(via control word sequence numbers), and could not be re-ordered, or could not fit in the jitter buffer. |
| 1.20.13.1.6.1.8 | ColumnpwTDMPerfIntervalMalformedPkt | read-only | current | Number of packets detected with unexpected size, or bad headers' stack |
| 1.20.13.1.6.1.9 | ColumnpwTDMPerfIntervalESs | read-only | current | The counter associated with the number of Error Seconds encountered. |
| 1.20.13.1.6.1.10 | ColumnpwTDMPerfIntervalSESs | read-only | current | The counter associated with the number of Severely Error Seconds encountered. |
| 1.20.13.1.6.1.11 | ColumnpwTDMPerfIntervalUASs | read-only | current | The counter associated with the number of Unavailable Seconds encountered. |
| 1.20.13.1.6.1.12 | ColumnpwTDMPerfIntervalFC | read-only | current | TDM Failure Counts (FC-TDM). The number of TDM failure events. A failure event begins when the LOPS failure is declared, and ends when the failure is cleared. … |
| 1.20.13.1.7 | TablepwTDMPerf1DayIntervalTable | not-accessible | current | This table provides performance information per TDM PW similar to the pwTDMPerfIntervalTable above. However, these counters represent historical 1 day interval… |
| 1.20.13.1.7.1 | RowpwTDMPerf1DayIntervalEntry | not-accessible | current | An entry is created in this table by the agent for every entry in the pwTDMTable table. |
| 1.20.13.1.7.1.1 | ColumnpwTDMPerf1DayIntervalNumber | not-accessible | current | The number of interval, where 1 indicates current day measured period and 2 and above indicate previous days respectively |
| 1.20.13.1.7.1.2 | ColumnpwTDMPerf1DayIntervalValidData | read-only | current | This variable indicates if the data for this interval is valid. |
| 1.20.13.1.7.1.3 | ColumnpwTDMPerf1DayIntervalDuration | read-only | current | The duration of a particular interval in seconds, Adjustments in the system's time-of-day clock, may cause the interval to be greater or less than, the normal … |
| 1.20.13.1.7.1.4 | ColumnpwTDMPerf1DayIntervalMissingPkts | read-only | current | Number of missing packets (as detected via control word sequence number gaps). |
| 1.20.13.1.7.1.5 | ColumnpwTDMPerf1DayIntervalPktsReOrder | read-only | current | Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this fea… |
| 1.20.13.1.7.1.6 | ColumnpwTDMPerf1DayIntervalJtrBfrUnderruns | read-only | current | Number of times a packet needed to be played out and the jitter buffer was empty. |
| 1.20.13.1.7.1.7 | ColumnpwTDMPerf1DayIntervalMisOrderDropped | read-only | current | Number of packets detected out of order(via control word sequence numbers), and could not be re-ordered, or could not fit in the jitter buffer. |
| 1.20.13.1.7.1.8 | ColumnpwTDMPerf1DayIntervalMalformedPkt | read-only | current | Number of packets detected with unexpected size, or bad headers' stack. |
| 1.20.13.1.7.1.9 | ColumnpwTDMPerf1DayIntervalESs | read-only | current | The counter associated with the number of Error Seconds encountered. |
| 1.20.13.1.7.1.10 | ColumnpwTDMPerf1DayIntervalSESs | read-only | current | The counter associated with the number of Severely Error Seconds. |
| 1.20.13.1.7.1.11 | ColumnpwTDMPerf1DayIntervalUASs | read-only | current | The counter associated with the number of UnAvailable Seconds. NOTE: When first entering the UAS state, the number of SES To UAS is added to this object, then … |
| 1.20.13.1.7.1.12 | ColumnpwTDMPerf1DayIntervalFC | read-only | current | TDM Failure Counts (FC-TDM). The number of TDM failure events. A failure event begins when the LOPS failure is declared, and ends when the failure is cleared. |
| 1.20.13.2 | NodepwTDMNotifications | |||
| 1.20.13.3 | NodepwTDMConformance | |||
| 1.20.13.3.1 | NodepwTDMGroups | |||
| 1.20.13.3.1.1 | GrouppwTDMGroup | current | Collection of objects for basic TDM PW config and status. | |
| 1.20.13.3.1.2 | GrouppwTDMPerfCurrentGroup | current | Collection of current statistics objects for TDM PWs. | |
| 1.20.13.3.1.3 | GrouppwTDMPerfIntervalGroup | current | Collection of Interval statistics objects for TDM PWs. | |
| 1.20.13.3.1.4 | GrouppwTDMPerf1DayIntervalGroup | current | Collection of Daily statistics objects for TDM PWs. | |
| 1.20.13.3.2 | NodepwTDMCompliances | |||
| 1.20.13.3.2.1 | CompliancepwTDMModuleCompliance | read-only | current | The compliance statement for agent that support TDM PW over PSN operation. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| PwTDMCfgIndex | Unsigned32 (1..4294967295) | current | Index into the relevant pwXXXCfgTable. |