PowerConnect3248-MIB
293 objects
The private MIB module definition for the Dell PowerConnect 3248 Network Switch.
Imported Objects
| BRIDGE-MIB | BridgeId dot1dStpPort dot1dStpPortEntry Timeout |
| IF-MIB | ifIndex |
| P-BRIDGE-MIB | EnabledStatus |
| Q-BRIDGE-MIB | PortList |
| SNMPv2-SMI | Counter32 Integer32 internet IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString RowStatus TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4 | Nodeprivate | |||
| 1.3.6.1.4.1 | Nodeenterprises | |||
| 1.3.6.1.4.1.674 | Nodedell | |||
| 1.3.6.1.4.1.674.10895 | NodedellLan | |||
| 1.3.6.1.4.1.674.10895.3 | IdentitypowerConnect3248MIB | The private MIB module definition for the Dell PowerConnect 3248 Network Switch. | ||
| 1.3.6.1.4.1.674.10895.3.1 | NodepowerConnect3248MIBObjects | |||
| 1.3.6.1.4.1.674.10895.3.1.1 | NodeswitchMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.1.1 | ScalarswitchManagementVlan | read-write | current | The VLAN on which management is done. |
| 1.3.6.1.4.1.674.10895.3.1.1.2 | ScalarswitchNumber | read-only | current | The total number of switches present on this system. |
| 1.3.6.1.4.1.674.10895.3.1.1.3 | TableswitchInfoTable | not-accessible | current | Table of descriptive and status information about switches in this system. |
| 1.3.6.1.4.1.674.10895.3.1.1.3.1 | RowswitchInfoEntry | not-accessible | current | An entry in the table, containing information about a single switch in this system. |
| 1.3.6.1.4.1.674.10895.3.1.1.3.1.1 | ColumnswUnitIndex | read-only | current | This object identifies the switch within the system for which this entry contains information. This value can never be greater than switchNumber. |
| 1.3.6.1.4.1.674.10895.3.1.1.3.1.2 | ColumnswHardwareVer | read-only | current | Hardware version of the main board. |
| 1.3.6.1.4.1.674.10895.3.1.1.3.1.3 | ColumnswMicrocodeVer | read-only | current | Microcode version of the main board. |
| 1.3.6.1.4.1.674.10895.3.1.1.3.1.4 | ColumnswLoaderVer | read-only | current | Loader version of the main board. |
| 1.3.6.1.4.1.674.10895.3.1.1.3.1.5 | ColumnswBootRomVer | read-only | current | Boot ROM code version of the main board. |
| 1.3.6.1.4.1.674.10895.3.1.1.3.1.6 | ColumnswOpCodeVer | read-only | current | Operation code version of the main board. |
| 1.3.6.1.4.1.674.10895.3.1.1.3.1.7 | ColumnswPortNumber | read-only | current | The total port number of this switch (including expansion slot). |
| 1.3.6.1.4.1.674.10895.3.1.1.3.1.8 | ColumnswPowerStatus | read-only | current | Indicates the switch using internalPower(1), redundantPower(2) or both(3) |
| 1.3.6.1.4.1.674.10895.3.1.1.3.1.9 | ColumnswRoleInSystem | read-only | current | Indicates the switch is master(1), backupMaster(2) or slave(3) in this system. |
| 1.3.6.1.4.1.674.10895.3.1.1.3.1.10 | ColumnswSerialNumber | read-only | current | Serial number of the switch. |
| 1.3.6.1.4.1.674.10895.3.1.1.3.1.11 | ColumnswExpansionSlot1 | read-only | current | Type of expansion module in this switch slot 1. |
| 1.3.6.1.4.1.674.10895.3.1.1.3.1.12 | ColumnswExpansionSlot2 | read-only | current | Type of expansion module in this switch slot 2. |
| 1.3.6.1.4.1.674.10895.3.1.1.3.1.13 | ColumnswServiceTag | read-only | current | Service tag serial-number of the switch. |
| 1.3.6.1.4.1.674.10895.3.1.1.4 | ScalarswitchOperState | read-only | current | Global operation state of the switch. |
| 1.3.6.1.4.1.674.10895.3.1.1.5 | NodeswitchProductId | |||
| 1.3.6.1.4.1.674.10895.3.1.1.5.1 | ScalarswProdName | read-only | current | |
| 1.3.6.1.4.1.674.10895.3.1.1.5.2 | ScalarswProdManufacturer | read-only | current | |
| 1.3.6.1.4.1.674.10895.3.1.1.5.3 | ScalarswProdDescription | read-only | current | |
| 1.3.6.1.4.1.674.10895.3.1.1.5.4 | ScalarswProdVersion | read-only | current | |
| 1.3.6.1.4.1.674.10895.3.1.1.5.5 | ScalarswProdUrl | read-only | current | |
| 1.3.6.1.4.1.674.10895.3.1.1.5.6 | ScalarswIdentifier | read-only | current | A unique identifier of which switch in the chassis is currently being looked at. |
| 1.3.6.1.4.1.674.10895.3.1.1.5.7 | ScalarswChassisServiceTag | read-only | current | The service tag of the chassis this switch resides in. |
| 1.3.6.1.4.1.674.10895.3.1.1.6 | TableswitchIndivPowerTable | not-accessible | current | Table about statuses of individual powers. |
| 1.3.6.1.4.1.674.10895.3.1.1.6.1 | RowswitchIndivPowerEntry | not-accessible | current | Table about statuses of individual powers. |
| 1.3.6.1.4.1.674.10895.3.1.1.6.1.1 | ColumnswIndivPowerUnitIndex | read-only | current | This is defined as swUnitIndex. |
| 1.3.6.1.4.1.674.10895.3.1.1.6.1.2 | ColumnswIndivPowerIndex | read-only | current | 1 means internal power. 2 means external power. |
| 1.3.6.1.4.1.674.10895.3.1.1.6.1.3 | ColumnswIndivPowerStatus | read-only | current | notPresent(1) means not present. green(2) means up. red(3) means down. |
| 1.3.6.1.4.1.674.10895.3.1.2 | NodeportMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.2.1 | TableportTable | not-accessible | current | Table of descriptive and status information about configuration of each switch port (including expansion slot) in this system. This table also contains informa… |
| 1.3.6.1.4.1.674.10895.3.1.2.1.1 | RowportEntry | not-accessible | current | An entry in the table, containing information about configuration in one switch port of the switch. |
| 1.3.6.1.4.1.674.10895.3.1.2.1.1.1 | ColumnportIndex | read-only | current | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.674.10895.3.1.2.1.1.2 | ColumnportName | read-write | current | Indicates the port name. This is same as ifAlias in the IF-MIB (RFC2863 or later). |
| 1.3.6.1.4.1.674.10895.3.1.2.1.1.3 | ColumnportType | read-only | current | Indicates the port type. |
| 1.3.6.1.4.1.674.10895.3.1.2.1.1.4 | ColumnportSpeedDpxCfg | read-write | current | Set the port speed and duplex mode as follows: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 1… |
| 1.3.6.1.4.1.674.10895.3.1.2.1.1.5 | ColumnportFlowCtrlCfg | read-write | current | (1) Flow control mechanism is enabled. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPr… |
| 1.3.6.1.4.1.674.10895.3.1.2.1.1.6 | ColumnportCapabilities | read-write | current | Port capabilities. |
| 1.3.6.1.4.1.674.10895.3.1.2.1.1.7 | ColumnportAutonegotiation | read-write | current | Whether autonegotiation is enabled. |
| 1.3.6.1.4.1.674.10895.3.1.2.1.1.8 | ColumnportSpeedDpxStatus | read-only | current | The operating speed and duplex mode of the switched port. If this index is a trunk, the speed is the speed of its individual members. If this index is a trunk … |
| 1.3.6.1.4.1.674.10895.3.1.2.1.1.9 | ColumnportFlowCtrlStatus | read-only | current | (2) BackPressure flow control machanism is used. (3) IEEE 802.3 flow control machanism is used. (4) Flow control mechanism is disabled. If this index is a trun… |
| 1.3.6.1.4.1.674.10895.3.1.2.1.1.10 | ColumnportTrunkIndex | read-only | current | The trunk to which this port belongs. A value of 0 means that this port does not belong to any trunk. A value greater than zero means that this port belongs to… |
| 1.3.6.1.4.1.674.10895.3.1.3 | NodetrunkMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.3.1 | ScalartrunkMaxId | read-only | current | The maximum number for a trunk identifier. |
| 1.3.6.1.4.1.674.10895.3.1.3.2 | ScalartrunkValidNumber | read-only | current | The number of valid trunks. |
| 1.3.6.1.4.1.674.10895.3.1.3.3 | TabletrunkTable | not-accessible | current | Table of descriptive and status information about configuration of each trunk, similar to Cisco EtherChannel. |
| 1.3.6.1.4.1.674.10895.3.1.3.3.1 | RowtrunkEntry | not-accessible | current | An entry in the table, containing information about configuration in one trunk of the switch. |
| 1.3.6.1.4.1.674.10895.3.1.3.3.1.1 | ColumntrunkIndex | read-only | current | This object identifies the trunk within the switch for which this entry contains information. |
| 1.3.6.1.4.1.674.10895.3.1.3.3.1.2 | ColumntrunkPorts | read-create | current | The complete set of ports currently associated with this trunk. |
| 1.3.6.1.4.1.674.10895.3.1.3.3.1.3 | ColumntrunkCreation | read-only | current | A value of static(1) means a statically configured trunk. A value of lacp(2) means an LACP-configured trunk. |
| 1.3.6.1.4.1.674.10895.3.1.3.3.1.4 | ColumntrunkStatus | read-create | current | Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.674.10895.3.1.4 | NodelacpMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.4.1 | TablelacpPortTable | not-accessible | current | Table for LACP port configuration. |
| 1.3.6.1.4.1.674.10895.3.1.4.1.1 | RowlacpPortEntry | not-accessible | current | Entry for LACP port configuration. |
| 1.3.6.1.4.1.674.10895.3.1.4.1.1.1 | ColumnlacpPortIndex | read-only | current | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.674.10895.3.1.4.1.1.2 | ColumnlacpPortStatus | read-write | current | Whether 802.3ad LACP is enabled. |
| 1.3.6.1.4.1.674.10895.3.1.5 | NodestaMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.5.1 | ScalarstaSystemStatus | read-write | current | Global spanning tree status. (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled. |
| 1.3.6.1.4.1.674.10895.3.1.5.2 | TablestaPortTable | not-accessible | current | The table manages port settings for Spanning Tree Protocol 802.1d, 802.1w or 802.1s depending on the value specified by staProtocolType. |
| 1.3.6.1.4.1.674.10895.3.1.5.2.1 | RowstaPortEntry | read-only | current | The conceptual entry of staPortTable. |
| 1.3.6.1.4.1.674.10895.3.1.5.2.1.1 | ColumnstaPortIndex | read-only | current | The port and the trunk (excluding trunk member ports) interface of the staPortTable. The interface identified by a particular value of this index is the same i… |
| 1.3.6.1.4.1.674.10895.3.1.5.2.1.2 | ColumnstaPortFastForward | read-write | current | Whether fast forwarding is enabled. |
| 1.3.6.1.4.1.674.10895.3.1.5.2.1.3 | ColumnstaPortProtocolMigration | read-write | current | When operating in RSTP (version 2) mode, writing TRUE(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effe… |
| 1.3.6.1.4.1.674.10895.3.1.5.2.1.4 | ColumnstaPortAdminEdgePort | read-write | current | The administrative value of the Edge Port parameter. A value of TRUE(1) indicates that this port should be assumed as an edge-port and a value of FALSE(2) indi… |
| 1.3.6.1.4.1.674.10895.3.1.5.2.1.5 | ColumnstaPortOperEdgePort | read-only | current | The operational value of the Edge Port parameter. The object is initialized to the value of staPortAdminEdgePort and is set FALSE when a BPDU is received. |
| 1.3.6.1.4.1.674.10895.3.1.5.2.1.6 | ColumnstaPortAdminPointToPoint | read-write | current | The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as… |
| 1.3.6.1.4.1.674.10895.3.1.5.2.1.7 | ColumnstaPortOperPointToPoint | read-only | current | The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection o… |
| 1.3.6.1.4.1.674.10895.3.1.5.2.1.8 | ColumnstaPortLongPathCost | read-write | current | The contribution of this port to the path cost (in 32 bits value) of paths towards the spanning tree root which include this port. This object is used to confi… |
| 1.3.6.1.4.1.674.10895.3.1.5.3 | ScalarstaProtocolType | read-write | current | The version of Spanning Tree Protocol the bridge is currently running. The value 'stp(1)' indicates the Spanning Tree Protocol is as specified in IEEE 802.1D,'… |
| 1.3.6.1.4.1.674.10895.3.1.5.4 | ScalarstaTxHoldCount | read-write | current | The value used by the Port Transmit state machine to limit the maximum transmission rate. |
| 1.3.6.1.4.1.674.10895.3.1.5.5 | ScalarstaPathCostMethod | read-write | current | Indicates the type of spanning tree path cost mode configured on the switch. This mode applies to all instances of the Spanning tree protocol running on the sw… |
| 1.3.6.1.4.1.674.10895.3.1.5.6 | NodexstMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.5.6.4 | TablexstInstanceCfgTable | not-accessible | current | This table is used to configure the property of a specific instance in Multiple Spanning Tree or Rapid Spanning Tree. If Rapid Spanning Tree protocol is in use… |
| 1.3.6.1.4.1.674.10895.3.1.5.6.4.1 | RowxstInstanceCfgEntry | read-only | current | A conceptual row containing the property of the MST or RST instance. |
| 1.3.6.1.4.1.674.10895.3.1.5.6.4.1.1 | ColumnxstInstanceCfgIndex | read-only | current | An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance. |
| 1.3.6.1.4.1.674.10895.3.1.5.6.4.1.2 | ColumnxstInstanceCfgPriority | read-write | current | The priority of a specific spanning tree instance. The value assigned should be in the range 0-61440 in steps of 4096. |
| 1.3.6.1.4.1.674.10895.3.1.5.6.4.1.3 | ColumnxstInstanceCfgTimeSinceTopologyChange | read-only | current | The time (in hundredths of second) since the last topology change detected by the bridge entity in MST or RST. |
| 1.3.6.1.4.1.674.10895.3.1.5.6.4.1.4 | ColumnxstInstanceCfgTopChanges | read-only | current | The total number of topology changes detected by this bridge in MST or RST since the management entity was last reset or initialized. |
| 1.3.6.1.4.1.674.10895.3.1.5.6.4.1.5 | ColumnxstInstanceCfgDesignatedRoot | read-only | current | The bridge identifier of the root of the spanning tree as determined by the Multiple Spanning Tree Protocol (1s) or Rapid Spanning Tree Protocol (1w) executed … |
| 1.3.6.1.4.1.674.10895.3.1.5.6.4.1.6 | ColumnxstInstanceCfgRootCost | read-only | current | The cost of the path to the root as seen from this bridge of the MST or RST. |
| 1.3.6.1.4.1.674.10895.3.1.5.6.4.1.7 | ColumnxstInstanceCfgRootPort | read-only | current | The number of the port which offers the lowest cost path from this bridge to the root bridge of the MST or RST. |
| 1.3.6.1.4.1.674.10895.3.1.5.6.4.1.8 | ColumnxstInstanceCfgMaxAge | read-only | current | The maximum age of Multiple Spanning Tree Protocol (1s) or Rapid Spanning Tree Protocol (1w) information learned from the network on any port before it is disc… |
| 1.3.6.1.4.1.674.10895.3.1.5.6.4.1.9 | ColumnxstInstanceCfgHelloTime | read-only | current | The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the specific spanning tree or trying t… |
| 1.3.6.1.4.1.674.10895.3.1.5.6.4.1.10 | ColumnxstInstanceCfgHoldTime | read-only | current | This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredth… |
| 1.3.6.1.4.1.674.10895.3.1.5.6.4.1.11 | ColumnxstInstanceCfgForwardDelay | read-only | current | For MST or RST protocol, this time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards … |
| 1.3.6.1.4.1.674.10895.3.1.5.6.4.1.12 | ColumnxstInstanceCfgBridgeMaxAge | read-only | current | For MST or RST protocol, the time (in hundredths of second) that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 speci… |
| 1.3.6.1.4.1.674.10895.3.1.5.6.4.1.13 | ColumnxstInstanceCfgBridgeHelloTime | read-only | current | For MST or RST protocol,the time (in hundredths of second) that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this t… |
| 1.3.6.1.4.1.674.10895.3.1.5.6.4.1.14 | ColumnxstInstanceCfgBridgeForwardDelay | read-only | current | For MST or RST protocol, the time (in hundredths of second) that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990… |
| 1.3.6.1.4.1.674.10895.3.1.5.6.4.1.15 | ColumnxstInstanceCfgTxHoldCount | read-only | current | For MST or RST protocol, the value used by the Port Transmit state machine to limit the maximum transmission rate. |
| 1.3.6.1.4.1.674.10895.3.1.5.6.4.1.16 | ColumnxstInstanceCfgPathCostMethod | read-only | current | For MST or RST protocol, this indicates the type of spanning tree path cost mode used by the switch. The mode applies to all instances of the Spanning Tree pro… |
| 1.3.6.1.4.1.674.10895.3.1.5.6.5 | TablexstInstancePortTable | not-accessible | current | The extension table for dot1dStpPortEntry to provide additional Spanning Tree information and configuration. |
| 1.3.6.1.4.1.674.10895.3.1.5.6.5.1 | RowxstInstancePortEntry | read-only | current | The conceptual row for xstInstancePortTable. |
| 1.3.6.1.4.1.674.10895.3.1.5.6.5.1.1 | ColumnxstInstancePortInstance | read-only | current | The instance of the MSTP. |
| 1.3.6.1.4.1.674.10895.3.1.5.6.5.1.2 | ColumnxstInstancePortPort | read-only | current | The port and the trunk (excluding trunk member ports) interface of the mstInstancePortTable. The interface identified by a particular value of this index is th… |
| 1.3.6.1.4.1.674.10895.3.1.5.6.5.1.3 | ColumnxstInstancePortPriority | read-write | current | Defines the priority used for this port in the Spanning Tree Algorithm. If the path cost for all ports on a switch is the same, the port with the highest prior… |
| 1.3.6.1.4.1.674.10895.3.1.5.6.5.1.4 | ColumnxstInstancePortState | read-only | current | The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame: discard… |
| 1.3.6.1.4.1.674.10895.3.1.5.6.5.1.5 | ColumnxstInstancePortEnable | read-only | current | The enabled/disabled status of the port. |
| 1.3.6.1.4.1.674.10895.3.1.5.6.5.1.6 | ColumnxstInstancePortPathCost | read-write | current | The pathcost of the MST or RST in the range 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should b… |
| 1.3.6.1.4.1.674.10895.3.1.5.6.5.1.7 | ColumnxstInstancePortDesignatedRoot | read-only | current | The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the po… |
| 1.3.6.1.4.1.674.10895.3.1.5.6.5.1.8 | ColumnxstInstancePortDesignatedCost | read-only | current | The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs. |
| 1.3.6.1.4.1.674.10895.3.1.5.6.5.1.9 | ColumnxstInstancePortDesignatedBridge | read-only | current | The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment. |
| 1.3.6.1.4.1.674.10895.3.1.5.6.5.1.10 | ColumnxstInstancePortDesignatedPort | read-only | current | The Port Identifier of the port on the Designated Bridge for this port's segment. |
| 1.3.6.1.4.1.674.10895.3.1.5.6.5.1.11 | ColumnxstInstancePortForwardTransitions | read-only | current | The number of times this port has transitioned from the Learning state to the Forwarding state. |
| 1.3.6.1.4.1.674.10895.3.1.5.6.5.1.12 | ColumnxstInstancePortPortRole | read-only | current | The role of the port in the MST or RST protocol: (1) The port has no role within the spanning tree (2) The port is part of the active topology connecting the b… |
| 1.3.6.1.4.1.674.10895.3.1.6 | NodetftpMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.6.1 | ScalartftpFileType | read-write | current | Type of file to transfer. |
| 1.3.6.1.4.1.674.10895.3.1.6.2 | ScalartftpSrcFile | read-write | current | The source file name for TFTP transfer when a transfer is next requested via this MIB. This value is set to the zero length string when no file name has been s… |
| 1.3.6.1.4.1.674.10895.3.1.6.3 | ScalartftpDestFile | read-write | current | The destination file name for TFTP transfer when a transfer is next requested via this MIB. This value is set to the zero length string when no file name has b… |
| 1.3.6.1.4.1.674.10895.3.1.6.4 | ScalartftpServer | read-write | current | The IP address of the TFTP server for transfer when a download is next requested via this MIB. This value is set to `0.0.0.0' when no IP address has been speci… |
| 1.3.6.1.4.1.674.10895.3.1.6.5 | ScalartftpAction | read-write | current | When this object is set to downloadToRAM(2) or downloadToPROM(3), the device will discontinue its normal operation and begin download of the file specified by … |
| 1.3.6.1.4.1.674.10895.3.1.6.6 | ScalartftpStatus | read-only | current | The status of the last transfer procedure, if any. This object will have a value of downloadStatusUnknown(2) if no transfer process has been performed. |
| 1.3.6.1.4.1.674.10895.3.1.7 | NoderestartMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.7.1 | ScalarrestartOpCodeFile | read-write | current | Name of op-code file for start-up. |
| 1.3.6.1.4.1.674.10895.3.1.7.2 | ScalarrestartConfigFile | read-write | current | Name of configuration file for start-up. |
| 1.3.6.1.4.1.674.10895.3.1.7.3 | ScalarrestartControl | read-write | current | Setting this object to warmBoot(2) causes the device to restart the application software with current configuration parameters saved in non-volatile memory. Se… |
| 1.3.6.1.4.1.674.10895.3.1.8 | NodemirrorMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.8.1 | TablemirrorTable | not-accessible | current | Table of descriptive and status information about switches in this system. |
| 1.3.6.1.4.1.674.10895.3.1.8.1.1 | RowmirrorEntry | not-accessible | current | An entry in the table, containing information about a single switch in this system. |
| 1.3.6.1.4.1.674.10895.3.1.8.1.1.1 | ColumnmirrorDestinationPort | read-only | current | Destination port for mirrored packets. This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.674.10895.3.1.8.1.1.2 | ColumnmirrorSourcePort | read-only | current | Source port for mirrored packets. This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.674.10895.3.1.8.1.1.3 | ColumnmirrorType | read-create | current | If this value is rx(1), receive packets will be mirrored. If this value is tx(2), transmit packets will be mirrored. If this value is both(3), both receive and… |
| 1.3.6.1.4.1.674.10895.3.1.8.1.1.4 | ColumnmirrorStatus | read-create | current | Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.674.10895.3.1.9 | NodeigmpSnoopMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.9.1 | ScalarigmpSnoopStatus | read-write | current | Parameter to enable or disable IGMP snooping on the device. When enabled, the device will examine IGMP packets and set up filters for IGMP ports. |
| 1.3.6.1.4.1.674.10895.3.1.9.2 | ScalarigmpSnoopQuerier | read-write | current | Whether to act as querier. |
| 1.3.6.1.4.1.674.10895.3.1.9.3 | ScalarigmpSnoopQueryCount | read-write | current | Maximum number of queries that have not been heard on the system before the system starts taking action to solicit reports. |
| 1.3.6.1.4.1.674.10895.3.1.9.4 | ScalarigmpSnoopQueryInterval | read-write | current | Query interval. |
| 1.3.6.1.4.1.674.10895.3.1.9.5 | ScalarigmpSnoopQueryMaxResponseTime | read-write | current | Timeout value (seconds) between IGMP reports received on a port for an IP Multicast Address that can pass before the system sends an IGMP Query out the port an… |
| 1.3.6.1.4.1.674.10895.3.1.9.6 | ScalarigmpSnoopQueryTimeout | read-write | current | Query time-out. |
| 1.3.6.1.4.1.674.10895.3.1.9.7 | ScalarigmpSnoopVersion | read-write | current | Version. |
| 1.3.6.1.4.1.674.10895.3.1.9.8 | TableigmpSnoopRouterCurrentTable | not-accessible | current | Table for current router ports. |
| 1.3.6.1.4.1.674.10895.3.1.9.8.1 | RowigmpSnoopRouterCurrentEntry | not-accessible | current | Entry for current router ports. |
| 1.3.6.1.4.1.674.10895.3.1.9.8.1.1 | ColumnigmpSnoopRouterCurrentVlanIndex | read-only | current | This is defined as dot1qVlanIndex in the Q-BRIDGE-MIB. |
| 1.3.6.1.4.1.674.10895.3.1.9.8.1.2 | ColumnigmpSnoopRouterCurrentPorts | read-only | current | The set of ports which are current router ports. Within this list, some router ports are static router ports. Please refer to igmpSnoopRouterStaticTable. |
| 1.3.6.1.4.1.674.10895.3.1.9.8.1.3 | ColumnigmpSnoopRouterCurrentStatus | read-only | current | The set of ports which are static router ports. |
| 1.3.6.1.4.1.674.10895.3.1.9.9 | TableigmpSnoopRouterStaticTable | not-accessible | current | Table for static router ports. |
| 1.3.6.1.4.1.674.10895.3.1.9.9.1 | RowigmpSnoopRouterStaticEntry | not-accessible | current | Entry for static router ports. |
| 1.3.6.1.4.1.674.10895.3.1.9.9.1.1 | ColumnigmpSnoopRouterStaticVlanIndex | read-only | current | This is defined as dot1qVlanIndex in the Q-BRIDGE-MIB. |
| 1.3.6.1.4.1.674.10895.3.1.9.9.1.2 | ColumnigmpSnoopRouterStaticPorts | read-create | current | The set of ports which are static router ports. |
| 1.3.6.1.4.1.674.10895.3.1.9.9.1.3 | ColumnigmpSnoopRouterStaticStatus | read-create | current | Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.674.10895.3.1.9.10 | TableigmpSnoopMulticastCurrentTable | not-accessible | current | Table for current multicast addresses. |
| 1.3.6.1.4.1.674.10895.3.1.9.10.1 | RowigmpSnoopMulticastCurrentEntry | not-accessible | current | Entry for current multicast addresses. |
| 1.3.6.1.4.1.674.10895.3.1.9.10.1.1 | ColumnigmpSnoopMulticastCurrentVlanIndex | read-only | current | This is defined as dot1qVlanIndex in the Q-BRIDGE-MIB. |
| 1.3.6.1.4.1.674.10895.3.1.9.10.1.2 | ColumnigmpSnoopMulticastCurrentIpAddress | read-only | current | IP address of multicast group. |
| 1.3.6.1.4.1.674.10895.3.1.9.10.1.3 | ColumnigmpSnoopMulticastCurrentPorts | read-only | current | The set of ports which are members. |
| 1.3.6.1.4.1.674.10895.3.1.9.10.1.4 | ColumnigmpSnoopMulticastCurrentStatus | read-only | current | The set of ports which are static members. |
| 1.3.6.1.4.1.674.10895.3.1.9.11 | TableigmpSnoopMulticastStaticTable | not-accessible | current | Table for static multicast addresses. |
| 1.3.6.1.4.1.674.10895.3.1.9.11.1 | RowigmpSnoopMulticastStaticEntry | not-accessible | current | Entry for static multicast addresses. |
| 1.3.6.1.4.1.674.10895.3.1.9.11.1.1 | ColumnigmpSnoopMulticastStaticVlanIndex | read-only | current | This is defined as dot1qVlanIndex in the Q-BRIDGE-MIB. |
| 1.3.6.1.4.1.674.10895.3.1.9.11.1.2 | ColumnigmpSnoopMulticastStaticIpAddress | read-only | current | IP address of multicast group. |
| 1.3.6.1.4.1.674.10895.3.1.9.11.1.3 | ColumnigmpSnoopMulticastStaticPorts | read-create | current | The set of ports which are members. |
| 1.3.6.1.4.1.674.10895.3.1.9.11.1.4 | ColumnigmpSnoopMulticastStaticStatus | read-create | current | Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.674.10895.3.1.10 | NodeipMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.10.1 | TablenetConfigTable | not-accessible | current | A table of netConfigEntries. |
| 1.3.6.1.4.1.674.10895.3.1.10.1.1 | RownetConfigEntry | not-accessible | current | A set of configuration parameters for a particular network interface on this device. If the device has no network interface, this table is empty. The index is … |
| 1.3.6.1.4.1.674.10895.3.1.10.1.1.1 | ColumnnetConfigIfIndex | read-only | current | VLAN interface on which this entry is defined. This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.674.10895.3.1.10.1.1.2 | ColumnnetConfigIPAddress | read-only | current | The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then w… |
| 1.3.6.1.4.1.674.10895.3.1.10.1.1.3 | ColumnnetConfigSubnetMask | read-only | current | The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then … |
| 1.3.6.1.4.1.674.10895.3.1.10.1.1.4 | ColumnnetConfigPrimaryInterface | read-create | current | Whether this is a primary interface. |
| 1.3.6.1.4.1.674.10895.3.1.10.1.1.5 | ColumnnetConfigUnnumbered | read-create | current | Whether this is an unnumbered interface. |
| 1.3.6.1.4.1.674.10895.3.1.10.1.1.6 | ColumnnetConfigStatus | read-create | current | The status of this netConfigEntry. An entry may not exist in the active state unless all objects in the entry have an appropriate value. |
| 1.3.6.1.4.1.674.10895.3.1.10.2 | ScalarnetDefaultGateway | read-write | current | The IP Address of the default gateway. If this value is undefined or unknown, it shall have the value 0.0.0.0. |
| 1.3.6.1.4.1.674.10895.3.1.10.3 | ScalaripHttpState | read-write | current | Whether HTTP is enabled. |
| 1.3.6.1.4.1.674.10895.3.1.10.4 | ScalaripHttpPort | read-write | current | The port number for HTTP. |
| 1.3.6.1.4.1.674.10895.3.1.10.5 | ScalaripDhcpRestart | read-write | current | Write it to restart(1) to restart DHCP. When read, this value always returns noRestart(2). |
| 1.3.6.1.4.1.674.10895.3.1.10.6 | ScalaripHttpsState | read-write | current | Whether HTTPS is enabled. |
| 1.3.6.1.4.1.674.10895.3.1.10.7 | ScalaripHttpsPort | read-write | current | The port number for HTTPS. |
| 1.3.6.1.4.1.674.10895.3.1.11 | NodebcastStormMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.11.1 | TablebcastStormTable | not-accessible | current | Table of descriptive and status information about configuration of each switch ports(including expansion slot) in this system. |
| 1.3.6.1.4.1.674.10895.3.1.11.1.1 | RowbcastStormEntry | not-accessible | current | An entry in the table, containing information about configuration in one switch port of the switch. |
| 1.3.6.1.4.1.674.10895.3.1.11.1.1.1 | ColumnbcastStormIfIndex | read-only | current | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.674.10895.3.1.11.1.1.2 | ColumnbcastStormStatus | read-write | current | Whether broadcast storm protection is enabled. |
| 1.3.6.1.4.1.674.10895.3.1.11.1.1.3 | ColumnbcastStormSampleType | read-write | current | Sample type. If this is pkt-rate(1), then bcastStormPktRate is valid. If this is octet-rate(2), then bcastStormOctetRate is valid. If this is percent(3), then … |
| 1.3.6.1.4.1.674.10895.3.1.11.1.1.4 | ColumnbcastStormPktRate | read-write | current | Broadcast storm threshold as packets per second. |
| 1.3.6.1.4.1.674.10895.3.1.11.1.1.5 | ColumnbcastStormOctetRate | read-write | current | Broadcast storm threshold as octets per second. |
| 1.3.6.1.4.1.674.10895.3.1.11.1.1.6 | ColumnbcastStormPercent | read-write | current | Broadcast storm threshold as percentage of bandwidth. |
| 1.3.6.1.4.1.674.10895.3.1.12 | NodevlanMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.12.1 | TablevlanTable | not-accessible | current | Table for VLAN configuration. |
| 1.3.6.1.4.1.674.10895.3.1.12.1.1 | RowvlanEntry | not-accessible | current | Entry for VLAN configuration. |
| 1.3.6.1.4.1.674.10895.3.1.12.1.1.1 | ColumnvlanIndex | read-only | current | Same is dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface. |
| 1.3.6.1.4.1.674.10895.3.1.12.1.1.2 | ColumnvlanAddressMethod | read-write | current | Method to get the IP address. |
| 1.3.6.1.4.1.674.10895.3.1.12.2 | TablevlanPortTable | not-accessible | current | Table for port configuration in VLAN. |
| 1.3.6.1.4.1.674.10895.3.1.12.2.1 | RowvlanPortEntry | not-accessible | current | Entry for port configuration in VLAN. |
| 1.3.6.1.4.1.674.10895.3.1.12.2.1.1 | ColumnvlanPortIndex | read-only | current | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.674.10895.3.1.12.2.1.2 | ColumnvlanPortMode | read-write | current | This variable sets the 802.1Q VLAN mode. Setting it to hybrid(1) sets a hybrid link. Setting it to dot1qTrunk(2) sets a trunk link. Setting it to access(3) set… |
| 1.3.6.1.4.1.674.10895.3.1.13 | NodepriorityMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.13.1 | ScalarprioIpPrecDscpStatus | read-write | current | Whether IP precedence or DSCP look-up is enabled. |
| 1.3.6.1.4.1.674.10895.3.1.13.2 | TableprioIpPrecTable | not-accessible | current | Table for IP precedence priority mapping. |
| 1.3.6.1.4.1.674.10895.3.1.13.2.1 | RowprioIpPrecEntry | not-accessible | current | Entry for IP precendence priority mapping. |
| 1.3.6.1.4.1.674.10895.3.1.13.2.1.2 | ColumnprioIpPrecPort | read-only | current | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.674.10895.3.1.13.2.1.3 | ColumnprioIpPrecValue | read-only | current | Precedence value for this entry. |
| 1.3.6.1.4.1.674.10895.3.1.13.2.1.4 | ColumnprioIpPrecCos | read-write | current | Class of service for this entry. |
| 1.3.6.1.4.1.674.10895.3.1.13.3 | ScalarprioIpPrecRestoreDefault | read-write | current | This object is to restore IP Precedence settings of a port to default. To do this, write it to the value of ifIndex defined by the ifIndex in the IF-MIB. When … |
| 1.3.6.1.4.1.674.10895.3.1.13.4 | TableprioIpDscpTable | not-accessible | current | Table for IP DSCP priority mapping. |
| 1.3.6.1.4.1.674.10895.3.1.13.4.1 | RowprioIpDscpEntry | not-accessible | current | Entry for IP DSCP priority mapping. |
| 1.3.6.1.4.1.674.10895.3.1.13.4.1.1 | ColumnprioIpDscpPort | read-only | current | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.674.10895.3.1.13.4.1.2 | ColumnprioIpDscpValue | read-only | current | DSCP value for this entry. |
| 1.3.6.1.4.1.674.10895.3.1.13.4.1.3 | ColumnprioIpDscpCos | read-write | current | Class of service for this entry. |
| 1.3.6.1.4.1.674.10895.3.1.13.5 | ScalarprioIpDscpRestoreDefault | read-write | current | This object is to restore IP DSCP settings of a port to default. To do this, write it to the value of ifIndex defined by the ifIndex in the IF-MIB. When read, … |
| 1.3.6.1.4.1.674.10895.3.1.13.6 | ScalarprioIpPortEnableStatus | read-write | current | Whether IP Port priority look-up is enabled. |
| 1.3.6.1.4.1.674.10895.3.1.13.7 | TableprioIpPortTable | not-accessible | current | Table for IP port priority mapping. |
| 1.3.6.1.4.1.674.10895.3.1.13.7.1 | RowprioIpPortEntry | not-accessible | current | Entry for IP port priority mapping. |
| 1.3.6.1.4.1.674.10895.3.1.13.7.1.1 | ColumnprioIpPortPhysPort | read-only | current | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.674.10895.3.1.13.7.1.2 | ColumnprioIpPortValue | read-only | current | IP port for this value. |
| 1.3.6.1.4.1.674.10895.3.1.13.7.1.3 | ColumnprioIpPortCos | read-create | current | Class of service for this entry. |
| 1.3.6.1.4.1.674.10895.3.1.13.7.1.4 | ColumnprioIpPortStatus | read-create | current | Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.674.10895.3.1.13.8 | NodeprioCopy | |||
| 1.3.6.1.4.1.674.10895.3.1.13.8.1 | ScalarprioCopyIpPrec | read-write | current | Action to copy IP Precedence settings from a source port to many destination ports. The first four octets represent an integer for the source port, in high-to-… |
| 1.3.6.1.4.1.674.10895.3.1.13.8.2 | ScalarprioCopyIpDscp | read-write | current | Action to copy IP DSCP settings from a source port to many destination ports. The first four octets represent an integer for the source port, in high-to-low (b… |
| 1.3.6.1.4.1.674.10895.3.1.13.8.3 | ScalarprioCopyIpPort | read-write | current | Action to copy IP Port settings from a source port to many destination ports. The first four octets represent an integer for the source port, in high-to-low (b… |
| 1.3.6.1.4.1.674.10895.3.1.13.9 | TableprioWrrTable | not-accessible | current | Table for weighted round robin (WRR). |
| 1.3.6.1.4.1.674.10895.3.1.13.9.1 | RowprioWrrEntry | not-accessible | current | Entry for weighted round robin (WRR). |
| 1.3.6.1.4.1.674.10895.3.1.13.9.1.1 | ColumnprioWrrTrafficClass | read-only | current | Traffic class for this entry, as defined in dot1dTrafficClass in the Q-BRIDGE-MIB. The actual maximum depends on the hardware, and is equal to dot1dPortNumTraf… |
| 1.3.6.1.4.1.674.10895.3.1.13.9.1.2 | ColumnprioWrrWeight | read-write | current | Weight for this entry. |
| 1.3.6.1.4.1.674.10895.3.1.14 | NodetrapDestMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.14.1 | TabletrapDestTable | not-accessible | current | A list of trap destination entries. |
| 1.3.6.1.4.1.674.10895.3.1.14.1.1 | RowtrapDestEntry | not-accessible | current | This entry includes a destination IP address to which to send traps for this community. |
| 1.3.6.1.4.1.674.10895.3.1.14.1.1.1 | ColumntrapDestAddress | read-only | current | The address to send traps. |
| 1.3.6.1.4.1.674.10895.3.1.14.1.1.2 | ColumntrapDestCommunity | read-create | current | A community to which this destination address belongs. |
| 1.3.6.1.4.1.674.10895.3.1.14.1.1.3 | ColumntrapDestStatus | read-create | current | Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.674.10895.3.1.14.1.1.4 | ColumntrapDestVersion | read-create | current | This variables represent the version of the Trap we wish to send to trap Receiver, if the value is 1, mean we wish to send Version 1 trap, if the value is 2, m… |
| 1.3.6.1.4.1.674.10895.3.1.17 | NodesecurityMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.17.2 | NodeportSecurityMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.17.2.1 | TableportSecPortTable | not-accessible | current | The Port Security(MAC bindind) Table |
| 1.3.6.1.4.1.674.10895.3.1.17.2.1.1 | RowportSecPortEntry | not-accessible | current | The entry of portSecPortTable |
| 1.3.6.1.4.1.674.10895.3.1.17.2.1.1.1 | ColumnportSecPortIndex | read-only | current | The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface… |
| 1.3.6.1.4.1.674.10895.3.1.17.2.1.1.2 | ColumnportSecPortStatus | read-write | current | Set enabled(1) to enable port security and set disabled(2) to disable port security. |
| 1.3.6.1.4.1.674.10895.3.1.17.2.1.1.3 | ColumnportSecAction | read-write | current | The corresponding actions that will take place when a port is under intruded, when this variable is set to none(1), no action will perform, when this variable … |
| 1.3.6.1.4.1.674.10895.3.1.17.4 | NoderadiusMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.17.4.1 | ScalarradiusServerAddress | read-write | current | IP address of RADIUS server. |
| 1.3.6.1.4.1.674.10895.3.1.17.4.2 | ScalarradiusServerPortNumber | read-write | current | IP port number of RADIUS server. |
| 1.3.6.1.4.1.674.10895.3.1.17.4.3 | ScalarradiusServerKey | read-write | current | Key for RADIUS. This variable can only be written. When this variable is read, it always returns a zero-length string. |
| 1.3.6.1.4.1.674.10895.3.1.17.4.4 | ScalarradiusServerRetransmit | read-write | current | Maximum number of retransmissions for RADIUS. |
| 1.3.6.1.4.1.674.10895.3.1.17.4.5 | ScalarradiusServerTimeout | read-write | current | Timeout for RADIUS. |
| 1.3.6.1.4.1.674.10895.3.1.17.5 | NodetacacsMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.17.5.1 | ScalartacacsServerAddress | read-write | current | IP address of TACACS server. |
| 1.3.6.1.4.1.674.10895.3.1.17.5.2 | ScalartacacsServerPortNumber | read-write | current | IP port number of TACACS server. |
| 1.3.6.1.4.1.674.10895.3.1.17.5.3 | ScalartacacsServerKey | read-write | current | Key for TACACS. |
| 1.3.6.1.4.1.674.10895.3.1.17.6 | NodesshMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.17.6.1 | ScalarsshServerStatus | read-write | current | The status of Secure Shell Server, set this value to 1 to enable SSH server, set this value to 2 to disable the SSH server. |
| 1.3.6.1.4.1.674.10895.3.1.17.6.2 | ScalarsshServerMajorVersion | read-only | current | The major version of the SSH Server. |
| 1.3.6.1.4.1.674.10895.3.1.17.6.3 | ScalarsshServerMinorVersion | read-only | current | The minor version of the SSH Server. |
| 1.3.6.1.4.1.674.10895.3.1.17.6.4 | ScalarsshTimeout | read-write | current | The time interval that the router waits for the SSH client to respond. The range is 1-120. |
| 1.3.6.1.4.1.674.10895.3.1.17.6.5 | ScalarsshAuthRetries | read-write | current | The number of attempts after which the interface is reset. The range is 1-5. |
| 1.3.6.1.4.1.674.10895.3.1.17.6.6 | TablesshConnInfoTable | not-accessible | current | The table for Secure Shell Connection. |
| 1.3.6.1.4.1.674.10895.3.1.17.6.6.1 | RowsshConnInfoEntry | not-accessible | current | The conceptual row for sshConnInfoTable. |
| 1.3.6.1.4.1.674.10895.3.1.17.6.6.1.1 | ColumnsshConnID | read-only | current | The connection ID of the Secure Shell Connection. |
| 1.3.6.1.4.1.674.10895.3.1.17.6.6.1.2 | ColumnsshConnMajorVersion | read-only | current | The SSH major version. |
| 1.3.6.1.4.1.674.10895.3.1.17.6.6.1.3 | ColumnsshConnMinorVersion | read-only | current | The SSH minor version. |
| 1.3.6.1.4.1.674.10895.3.1.17.6.6.1.4 | ColumnsshConnEncryptionType | read-only | current | The encryption type of the SSH. none(1) mean no encrytion , des(2) mean using DES encrytion, tribeDes mean using 3DES encrytion. |
| 1.3.6.1.4.1.674.10895.3.1.17.6.6.1.5 | ColumnsshConnStatus | read-only | current | The SSH connection State. negotiationStart(1) mean the SSH is in its negotiation start state, authenticationStart(2) mean the SSH is in authentication start st… |
| 1.3.6.1.4.1.674.10895.3.1.17.6.6.1.6 | ColumnsshConnUserName | read-only | current | The user name of the connection. |
| 1.3.6.1.4.1.674.10895.3.1.17.6.6.1.7 | ColumnsshDisconnect | read-write | current | Set the variables to disconnect to disconnect the connection, when read, this variables always return noDisconnect(1). |
| 1.3.6.1.4.1.674.10895.3.1.19 | NodesysLogMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.19.1 | ScalarsysLogStatus | read-write | current | Whether system log is enabled. |
| 1.3.6.1.4.1.674.10895.3.1.19.2 | ScalarsysLogHistoryFlashLevel | read-write | current | Severity level for logging to flash. |
| 1.3.6.1.4.1.674.10895.3.1.19.3 | ScalarsysLogHistoryRamLevel | read-write | current | Severity level for logging to RAM. |
| 1.3.6.1.4.1.674.10895.3.1.19.6 | NoderemoteLogMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.19.6.1 | ScalarremoteLogStatus | read-write | current | Whether the remote log system is enabled. |
| 1.3.6.1.4.1.674.10895.3.1.19.6.2 | ScalarremoteLogLevel | read-write | current | Severity level for remote log. |
| 1.3.6.1.4.1.674.10895.3.1.19.6.3 | ScalarremoteLogFacilityType | read-write | current | The FacilityType for remote log. |
| 1.3.6.1.4.1.674.10895.3.1.19.6.4 | TableremoteLogServerTable | not-accessible | current | A Table for storing the remote log Server list. |
| 1.3.6.1.4.1.674.10895.3.1.19.6.4.1 | RowremoteLogServerEntry | not-accessible | current | A conceptually row for remoteLogServerTable. |
| 1.3.6.1.4.1.674.10895.3.1.19.6.4.1.1 | ColumnremoteLogServerIp | read-create | current | The IP address of the remote log Server. |
| 1.3.6.1.4.1.674.10895.3.1.19.6.4.1.2 | ColumnremoteLogServerStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.674.10895.3.1.20 | NodelineMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.20.1 | NodeconsoleMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.20.1.1 | ScalarconsoleDataBits | read-write | current | Number of data bits. |
| 1.3.6.1.4.1.674.10895.3.1.20.1.2 | ScalarconsoleParity | read-write | current | Define the generation of a parity bit. |
| 1.3.6.1.4.1.674.10895.3.1.20.1.3 | ScalarconsoleBaudRate | read-write | current | Baud rate. Valid values are 115200, 57600, 38400, 19200, and 9600. |
| 1.3.6.1.4.1.674.10895.3.1.20.1.4 | ScalarconsoleStopBits | read-write | current | The stop Bits of the console, valid value is stopbits1(1) or stopbits2(2) |
| 1.3.6.1.4.1.674.10895.3.1.20.1.5 | ScalarconsoleExecTimeout | read-write | current | In serial console, use the consoleExecTimeout variables to set the interval that the EXEC command interpreter waits until user input is detected, set the value… |
| 1.3.6.1.4.1.674.10895.3.1.20.1.6 | ScalarconsolePasswordThreshold | read-write | current | In serial console, use the consolePasswordThreshold variabes to set the password intrusion threshold, which limits the number of failed logon attempts allowed.… |
| 1.3.6.1.4.1.674.10895.3.1.20.1.7 | ScalarconsoleSilentTime | read-write | current | In Console, Use the consoleSilentTime variable to set the amount of time the management console is inaccessible after the number of unsuccessful logon attempts… |
| 1.3.6.1.4.1.674.10895.3.1.20.2 | NodetelnetMgt | |||
| 1.3.6.1.4.1.674.10895.3.1.20.2.1 | ScalartelnetExecTimeout | read-write | current | In a telnet session, to set the interval that the EXEC command interpreter waits until user input is detected, use the telnetExecTimeout variables. |
| 1.3.6.1.4.1.674.10895.3.1.20.2.2 | ScalartelnetPasswordThreshold | read-write | current | In a telnet session, use the consolePasswordThreshold variabes to set the password intrusion threshold, which limits the number of failed logon attempts allowe… |
| 1.3.6.1.4.1.674.10895.3.2 | NodepowerConnect3248Notifications | |||
| 1.3.6.1.4.1.674.10895.3.2.1 | NodepowerConnect3248Traps | |||
| 1.3.6.1.4.1.674.10895.3.2.1.0 | NodepowerConnect3248TrapsPrefix | |||
| 1.3.6.1.4.1.674.10895.3.2.1.0.1 | NotificationswPowerStatusChangeTrap | current | This trap is sent when the power status of an individual power changes. | |
| 1.3.6.1.4.1.674.10895.3.2.1.0.36 | NotificationswPortSecurityTrap | current | This trap is sent when the port is being intruded. This trap will only be sent when the portSecActionTrap is enabled. | |
| 1.3.6.1.4.1.674.10895.3.3 | NodepowerConnect3248Conformance |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| ValidStatus | INTEGER { valid(1), invalid(2) } | current | A simple status value for the object to create and destroy a table entry. This is a simplified variant of RowStatus as it supports only two values. Setting it to valid(1) creates an entry. Setting it to invalid(2) destr… |