QTECH-RRM-MIB
310 objects
This module defines wlan rrm mibs.
Imported Objects
| QTECH-SMI | qtechMgmt |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString MacAddress TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.27514.1.1.10.2.63 | IdentityqtechRrmMIB | This module defines wlan rrm mibs. | ||
| 1.3.6.1.4.1.27514.1.1.10.2.63.1 | NodeqtechRrmMIBObjects | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.1 | NodeqtechRrmObjectsGroup | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.1.1 | ScalarqtechRrmRFNetworkName | read-write | current | RF Network Group Name to which this Qtech Switch belongs. Airespace Switches on a network form a RF Network Group as well as a Mobility Group. RF Network Group… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2 | NodeqtechRrmObjectsDot11a | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.1 | NodeqtechRrmDCADot11a | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.1.1 | ScalarqtechRrmDot11aDynamicChannelAssignment | read-write | current | Dynamic channel assignment(DCA) has three modes. When the mode is auto, the channel assignment will be periodically updated for all APs that permit this operat… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.1.2 | ScalarqtechRrmDot11aAnchorTime | read-write | current | the time of DCA algorithm to start |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.1.3 | ScalarqtechRrmDot11aChannalWidth11n | read-write | current | channel width in DCA for 802.11n |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.1.4 | ScalarqtechRrmDot11aDynamicChannelUpdateInterval | read-write | current | When Channel dynamic alogirthm is running, this interval (in secs) specifies how often Channel assignement updates are attempted on an AP. NOTE: hysteresis is … |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.1.5 | ScalarqtechRrmDot11aDCASensitivity | read-write | current | Consider foreign factor in DCA algorithm |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.1.6 | ScalarqtechRrmDot11aForeignInterfereFactorEnable | read-write | current | Consider foreign factor in DCA algorithm |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.1.7 | ScalarqtechRrmDot11aLoadFactorEnable | read-write | current | Consider foreign factor in DCA algorithm |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.1.8 | ScalarqtechRrmDot11aNoiseFactorEnable | read-write | current | Consider foreign factor in DCA algorithm |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.1.9 | ScalarqtechRrmDot11aChannelUpdateCmdInvoke | read-write | current | When set to activate this starts a DCA calculation regardless of the dynamic update interval. This command should be invoke on Group Leader Qtech Switch.Invoki… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.1.10 | TableqtechRrmDot11aDCAChannelTable | not-accessible | current | This is a table of Qtech Switch addresses that identifies the members of the Dot11a RF group containing this Qtech Switch. Max size is 20 entries. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.1.10.1 | RowqtechRrmDot11aDCAChannelEntry | not-accessible | current | ... |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.1.10.1.1 | ColumnqtechRrmDot11aDCAChannelIndex | read-only | current | the index of dca channel. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.1.10.1.2 | ColumnqtechRrmDot11aDCAChannelOperation | read-write | current | add or delete the channel using in DCA algorithm. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.2 | NodeqtechRrmTPCDot11a | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.2.1 | ScalarqtechRrmDot11aDTPCSupport | read-write | current | This attribute may be used to enable the DTPC support on all 802.11b/g radios. DTPC or Dynamic Transmit Power Control support means that the radio's transmit p… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.2.2 | ScalarqtechRrmDot11aDynamicTransmitPowerControl | read-write | current | Dynamic transmit power (DTP) has three modes. When the mode is auto, the transmit power of each Qtech AP will be periodically updated for all Qtech APs that pe… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.2.3 | ScalarqtechRrmDot11aDynamicTxPowerControlInterval | read-only | current | When Tx PowerControl dynamic alogirthm is running, this interval(in secs) specifies how often TxPower control updates are attempted on an Qtech AP. NOTE: hyste… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.2.4 | ScalarqtechRrmDot11aCurrentTxPowerLevel | read-write | current | The TxPowerLevel N currently being used to transmit data. Some PHYs also use this value to determine the receiver sensitivity requirements for CCA. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.2.5 | ScalarqtechRrmDot11aPowerUpdateCmdInvoke | read-write | current | When set to activate this starts a DTP calculation regardless of the dynamic update interval. This command should be invoke on Group Leader Qtech Switch.Invoki… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.2.6 | ScalarqtechRrmDot11aTXPowerThreshold | read-write | current | threshold value in TPC algorithm |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.2.7 | ScalarqtechRrmDot11aTPCNeighborNumber | read-only | current | threshold value in TPC algorithm |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.3 | NodeqtechRrmCHDDot11a | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.3.1 | ScalarqtechRrmDot11aCoverageEnable | read-write | current | CHD algorighm. Default is enable. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.3.2 | ScalarqtechRrmDot11aCoverageExceptionGlobal | read-write | current | CHD algorighm. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.3.3 | ScalarqtechRrmDot11aCoverageLevelGlobal | read-write | current | CHD algorighm. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.3.4 | ScalarqtechRrmDot11aCoverageDataRSSIThreshold | read-write | current | CHD algorighm. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.3.5 | ScalarqtechRrmDot11aCoverageVoiceRSSIThreshold | read-write | current | CHD algorighm. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.3.6 | ScalarqtechRrmDot11aCoverageDataPacketCount | read-write | current | CHD algorighm. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.3.7 | ScalarqtechRrmDot11aCoverageVoicePacketCount | read-write | current | CHD algorighm. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.3.8 | ScalarqtechRrmDot11aCoverageDataFailRate | read-write | current | CHD algorighm. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.3.9 | ScalarqtechRrmDot11aCoverageVoiceFailRate | read-write | current | CHD algorighm. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.4 | NodeqtechRrmGroupDot11a | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.4.1 | ScalarqtechRrmDot11aGlobalAutomaticGrouping | read-write | current | Dynamic grouping has two modes: on and off. When the grouping is off, no dynamic grouping occurs. Each Qtech Switch optimizes only its own Qtech APs' parameter… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.4.2 | ScalarqtechRrmDot11aGroupLeaderMacAddr | read-only | current | This is the MAC address of the group leader for the dot11a group containing this Qtech Switch. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.4.3 | ScalarqtechRrmDot11aGroupLeader | read-only | current | If this Qtech Switch is a Dot11a Group Leader then this attribute will be true else it will be false. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.4.4 | ScalarqtechRrmDot11aGroupLastUpdateTime | read-only | current | Last time the dot11a grouping was updated on this Qtech Switch. This is valid only if the Qtech Switch is a group leader. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.4.5 | ScalarqtechRrmDot11aGroupInterval | read-only | current | When grouping is on, this interval(in secs) represents the period with which the grouping algorithm is run. Grouping algorithm will also run when the group con… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.4.6 | TableqtechRrmDot11aGroupTable | not-accessible | current | This is a table of Qtech Switch addresses that identifies the members of the Dot11a RF group containing this Qtech Switch. Max size is 20 entries. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.4.6.1 | RowqtechRrmDot11aGroupEntry | not-accessible | current | ... |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.4.6.1.1 | ColumnqtechRrmDot11aPeerMacAddress | read-only | current | The MAC address of the member Switch. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.4.6.1.2 | ColumnqtechRrmDot11aPeerIpAddress | read-only | current | The IP address of the Qtech Switch. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.4.7 | TableqtechRrmDot11aSummaryTable | not-accessible | current | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.4.7.1 | RowqtechRrmDot11aSummaryEntry | not-accessible | current | ... |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.4.7.1.1 | ColumnqtechRrmDot11aAPname | read-only | current | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.4.7.1.2 | ColumnqtechRrmDot11aAPRadioID | read-only | current | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.4.7.1.3 | ColumnqtechRrmDot11aAPChannel | read-only | current | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.4.7.1.4 | ColumnqtechRrmDot11aAPTxPower | read-only | current | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.4.7.1.5 | ColumnqtechRrmDot11aAPChannelRrmChangeFlag | read-only | current | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.4.7.1.6 | ColumnqtechRrmDot11aAPTxPowerRrmChangeFlag | read-only | current | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.4.7.1.7 | ColumnqtechRrmDot11aSummaryMacAddress | read-only | current | The MAC address of the member Switch. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.5 | NodeqtechRrmProfileDot11a | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.5.1 | ScalarqtechRrmDot11aForeignInterferenceThreshold | read-write | current | foreign 802.11A interference threshold between 0 and 100 percent. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.5.2 | ScalarqtechRrmDot11aForeignNoiseThreshold | read-write | current | 802.11A foreign noise threshold between -127 and 0 dBm. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.5.3 | ScalarqtechRrmDot11aRFUtilizationThreshold | read-write | current | 802.11A RF utlization threshold between 0 and 100 percent. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.5.4 | ScalarqtechRrmDot11aThroughputThreshold | read-write | current | 802.11A throughput threshold between 1000 and 10000000 |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.5.5 | ScalarqtechRrmDot11aMobilesThreshold | read-write | current | 802.11A mobiles threshold between 1 and 75 |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.6 | NodeqtechRrmMonitorDot11a | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.6.1 | ScalarqtechRrmDot11aMonitorEnable | read-write | current | Enable or disable monitor function. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.6.2 | ScalarqtechRrmDot11aChannelMonitorList | read-write | current | This attribute specifies the channels on which the switch monitors noise, interference and rogues. The first option allows monitoring on all channels while the… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.6.3 | ScalarqtechRrmDot11aMonitorInterval | read-write | current | This interval( in secs) specifies how often the AP goto off channel state to monitor. Default is 300 secs |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.6.4 | ScalarqtechRrmDot11aCoverageMeasurementInterval | read-write | current | This interval( in secs) specifies how often do we get new coverage measurements at each Qtech AP. Default is 300 secs |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.6.5 | ScalarqtechRrmDot11aLoadMeasurementInterval | read-write | current | This interval( in secs) specifies how often do we get new load measurements at each Qtech AP. Default is 300 secs |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.6.6 | ScalarqtechRrmDot11aNoiseMeasurementInterval | read-write | current | This interval( in secs) specifies how often do we get new noise and interference measurements at each Qtech AP. Default is 300 secs |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.6.7 | ScalarqtechRrmDot11aSignalMeasurementInterval | read-write | current | This interval (in secs) specifies how often do we get new signal strength measurements at each Qtech AP. Default is 300 secs |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.6.8 | ScalarqtechRrmDot11aNeighborMessageInterval | read-write | current | This interval (in secs) specifies how often the AP send neighbor message |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.7 | NodeqtechRrmFactoryDot11a | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.2.7.1 | ScalarqtechRrmDot11aSetFactoryDefault | read-write | current | When set to activate all Rrm parameters are reset to factory defaults |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3 | NodeqtechRrmObjectsDot11b | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.1 | NodeqtechRrmDCADot11b | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.1.1 | ScalarqtechRrmDot11bDynamicChannelAssignment | read-write | current | Dynamic channel assignment(DCA) has three modes. When the mode is auto, the channel assignment will be periodically updated for all APs that permit this operat… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.1.2 | ScalarqtechRrmDot11bAnchorTime | read-write | current | the time of DCA algorithm to start |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.1.3 | ScalarqtechRrmDot11bChannalWidth11n | read-write | current | channel width in DCA for 802.11n |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.1.4 | ScalarqtechRrmDot11bDynamicChannelUpdateInterval | read-write | current | When Channel dynamic alogirthm is running, this interval (in secs) specifies how often Channel assignement updates are attempted on an AP. NOTE: hysteresis is … |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.1.5 | ScalarqtechRrmDot11bDCASensitivity | read-write | current | Consider foreign factor in DCA algorithm |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.1.6 | ScalarqtechRrmDot11bForeignInterfereFactorEnable | read-write | current | Consider foreign factor in DCA algorithm |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.1.7 | ScalarqtechRrmDot11bLoadFactorEnable | read-write | current | Consider foreign factor in DCA algorithm |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.1.8 | ScalarqtechRrmDot11bNoiseFactorEnable | read-write | current | Consider foreign factor in DCA algorithm |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.1.9 | ScalarqtechRrmDot11bChannelUpdateCmdInvoke | read-write | current | When set to activate this starts a DCA calculation regardless of the dynamic update interval. This command should be invoke on Group Leader Qtech Switch.Invoki… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.1.10 | TableqtechRrmDot11bDCAChannelTable | not-accessible | current | This is a table of Qtech Switch addresses that identifies the members of the Dot11a RF group containing this Qtech Switch. Max size is 20 entries. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.1.10.1 | RowqtechRrmDot11bDCAChannelEntry | not-accessible | current | ... |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.1.10.1.1 | ColumnqtechRrmDot11bDCAChannelIndex | read-only | current | the index of dca channel. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.1.10.1.2 | ColumnqtechRrmDot11bDCAChannelOperation | read-write | current | add or delete the channel using in DCA algorithm. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.2 | NodeqtechRrmTPCDot11b | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.2.1 | ScalarqtechRrmDot11bDTPCSupport | read-write | current | This attribute may be used to enable the DTPC support on all 802.11b/g radios. DTPC or Dynamic Transmit Power Control support means that the radio's transmit p… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.2.2 | ScalarqtechRrmDot11bDynamicTransmitPowerControl | read-write | current | Dynamic transmit power (DTP) has three modes. When the mode is auto, the transmit power of each Qtech AP will be periodically updated for all Qtech APs that pe… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.2.3 | ScalarqtechRrmDot11bDynamicTxPowerControlInterval | read-only | current | When Tx PowerControl dynamic alogirthm is running, this interval(in secs) specifies how often TxPower control updates are attempted on an Qtech AP. NOTE: hyste… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.2.4 | ScalarqtechRrmDot11bCurrentTxPowerLevel | read-write | current | The TxPowerLevel N currently being used to transmit data. Some PHYs also use this value to determine the receiver sensitivity requirements for CCA. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.2.5 | ScalarqtechRrmDot11bPowerUpdateCmdInvoke | read-write | current | When set to activate this starts a DTP calculation regardless of the dynamic update interval. This command should be invoke on Group Leader Qtech Switch.Invoki… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.2.6 | ScalarqtechRrmDot11bTXPowerThreshold | read-write | current | threshold value in TPC algorithm |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.2.7 | ScalarqtechRrmDot11bTPCNeighborNumber | read-only | current | threshold value in TPC algorithm |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.3 | NodeqtechRrmCHDDot11b | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.3.1 | ScalarqtechRrmDot11bCoverageEnable | read-write | current | CHD algorighm. Default is enable. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.3.2 | ScalarqtechRrmDot11bCoverageExceptionGlobal | read-write | current | CHD algorighm. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.3.3 | ScalarqtechRrmDot11bCoverageLevelGlobal | read-write | current | CHD algorighm. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.3.4 | ScalarqtechRrmDot11bCoverageDataRSSIThreshold | read-write | current | CHD algorighm. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.3.5 | ScalarqtechRrmDot11bCoverageVoiceRSSIThreshold | read-write | current | CHD algorighm. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.3.6 | ScalarqtechRrmDot11bCoverageDataPacketCount | read-write | current | CHD algorighm. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.3.7 | ScalarqtechRrmDot11bCoverageVoicePacketCount | read-write | current | CHD algorighm. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.3.8 | ScalarqtechRrmDot11bCoverageDataFailRate | read-write | current | CHD algorighm. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.3.9 | ScalarqtechRrmDot11bCoverageVoiceFailRate | read-write | current | CHD algorighm. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.4 | NodeqtechRrmGroupDot11b | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.4.1 | ScalarqtechRrmDot11bGlobalAutomaticGrouping | read-write | current | Dynamic grouping has two modes: on and off. When the grouping is off, no dynamic grouping occurs. Each Qtech Switch optimizes only its own Qtech APs' parameter… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.4.2 | ScalarqtechRrmDot11bGroupLeaderMacAddr | read-only | current | This is the MAC address of the group leader for the Dot11b group containing this Qtech Switch. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.4.3 | ScalarqtechRrmDot11bGroupLeader | read-only | current | If this Qtech Switch is a Dot11b Group Leader then this attribute will be true else it will be false. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.4.4 | ScalarqtechRrmDot11bGroupLastUpdateTime | read-only | current | Last time the Dot11b grouping was updated on this Qtech Switch. This is valid only if the Qtech Switch is a group leader. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.4.5 | ScalarqtechRrmDot11bGroupInterval | read-only | current | When grouping is on, this interval(in secs) represents the period with which the grouping algorithm is run. Grouping algorithm will also run when the group con… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.4.6 | TableqtechRrmDot11bGroupTable | not-accessible | current | This is a table of Qtech Switch addresses that identifies the members of the Dot11b RF group containing this Qtech Switch. Max size is 20 entries. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.4.6.1 | RowqtechRrmDot11bGroupEntry | not-accessible | current | ... |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.4.6.1.1 | ColumnqtechRrmDot11bPeerMacAddress | read-only | current | The MAC address of the member Switch. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.4.6.1.2 | ColumnqtechRrmDot11bPeerIpAddress | read-only | current | The IP address of the Qtech Switch. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.4.7 | TableqtechRrmDot11bSummaryTable | not-accessible | current | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.4.7.1 | RowqtechRrmDot11bSummaryEntry | not-accessible | current | ... |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.4.7.1.1 | ColumnqtechRrmDot11bAPname | read-only | current | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.4.7.1.2 | ColumnqtechRrmDot11bAPRadioID | read-only | current | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.4.7.1.3 | ColumnqtechRrmDot11bAPChannel | read-only | current | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.4.7.1.4 | ColumnqtechRrmDot11bAPTxPower | read-only | current | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.4.7.1.5 | ColumnqtechRrmDot11bAPChannelRrmChangeFlag | read-only | current | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.4.7.1.6 | ColumnqtechRrmDot11bAPTxPowerRrmChangeFlag | read-only | current | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.4.7.1.7 | ColumnqtechRrmDot11bSummaryMacAddress | read-only | current | The MAC address of the member Switch. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.5 | NodeqtechRrmProfileDot11b | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.5.1 | ScalarqtechRrmDot11bForeignInterferenceThreshold | read-write | current | foreign 802.11B interference threshold between 0 and 100 percent. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.5.2 | ScalarqtechRrmDot11bForeignNoiseThreshold | read-write | current | 802.11B foreign noise threshold between -127 and 0 dBm. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.5.3 | ScalarqtechRrmDot11bRFUtilizationThreshold | read-write | current | 802.11B RF utlization threshold between 0 and 100 percent. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.5.4 | ScalarqtechRrmDot11bThroughputThreshold | read-write | current | 802.11B throughput threshold between 1000 and 10000000 |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.5.5 | ScalarqtechRrmDot11bMobilesThreshold | read-write | current | 802.11B mobiles threshold between 1 and 75 |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.6 | NodeqtechRrmMonitorDot11b | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.6.1 | ScalarqtechRrmDot11bMonitorEnable | read-write | current | Enable or disable monitor function. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.6.2 | ScalarqtechRrmDot11bChannelMonitorList | read-write | current | This attribute specifies the channels on which the switch monitors noise, interference and rogues. The first option allows monitoring on all channels while the… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.6.3 | ScalarqtechRrmDot11bMonitorInterval | read-write | current | This interval( in secs) specifies how often the AP goto off channel state to monitor. Default is 300 secs |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.6.4 | ScalarqtechRrmDot11bCoverageMeasurementInterval | read-write | current | This interval( in secs) specifies how often do we get new coverage measurements at each Qtech AP. Default is 300 secs |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.6.5 | ScalarqtechRrmDot11bLoadMeasurementInterval | read-write | current | This interval( in secs) specifies how often do we get new load measurements at each Qtech AP. Default is 300 secs |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.6.6 | ScalarqtechRrmDot11bNoiseMeasurementInterval | read-write | current | This interval( in secs) specifies how often do we get new noise and interference measurements at each Qtech AP. Default is 300 secs |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.6.7 | ScalarqtechRrmDot11bSignalMeasurementInterval | read-write | current | This interval (in secs) specifies how often do we get new signal strength measurements at each Qtech AP. Default is 300 secs |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.6.8 | ScalarqtechRrmDot11bNeighborMessageInterval | read-write | current | This interval (in secs) specifies how often the AP send neighbor message |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.7 | NodeqtechRrmFactoryDot11b | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.3.7.1 | ScalarqtechRrmDot11bSetFactoryDefault | read-write | current | When set to activate all Rrm parameters are reset to factory defaults |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4 | NodeqtechRrmObjectsAP | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.1 | ScalarqtechRrmAPIfSlotId | read-only | current | Number of Radio Interfaces on the Airespace AP. Currently maximum two interfaces are supported. One would be of type 802.11a and other of type 802.11b/g. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.2 | ScalarqtechRrmAPName | read-only | current | Name assigned to this AP. If an AP is not configured its factory default name will be ap:<last three byte of MACAddress> eg. ap:af:12:be |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.3 | TableqtechRrmAPIfProfileThresholdConfigTable | not-accessible | current | Table of attributes for various thresholds to be set on each Airespace AP Interface for Load performance profile , interference performance profile and Noise p… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.3.1 | RowqtechRrmAPIfProfileThresholdConfigEntry | not-accessible | current | An entry (conceptual row) in the Phy Thresholds Table. Entries in this MIB are indexed by qtechRrmAPDot3MacAddress and qtechRrmAPIfSlotId |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.3.1.1 | ColumnqtechRrmAPIfThresholdRadioType | read-only | current | radio type, type 802.11b means 2.4GHz, type 802.11a means 5GHz, |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.3.1.2 | ColumnqtechRrmAPIfForeignInterferenceThreshold | read-write | current | foreign interference threshold between 1 and 100 percent. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.3.1.3 | ColumnqtechRrmAPIfForeignNoiseThreshold | read-write | current | foreign noise threshold between -127 and 0 dBm. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.3.1.4 | ColumnqtechRrmAPIfRFUtilizationThreshold | read-write | current | RF utlization threshold between 1 and 100 percent. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.3.1.5 | ColumnqtechRrmAPIfThroughputThreshold | read-write | current | Airespace AP data-rate threshold between 1000 and 1000000000. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.3.1.6 | ColumnqtechRrmAPIfMobilesThreshold | read-write | current | Airespace AP mobiles threshold between 1 and 128. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.3.1.7 | ColumnqtechRrmAPIfThresholdName | read-only | current | The name of the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.3.1.8 | ColumnqtechRrmAPIfThresholdMacAddr | read-only | current | The MAC address of radio on the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.3.1.9 | ColumnqtechRrmAPIfForeignGlobalConfig | read-write | current | Interference threshold inherited from global or not, 1: global config, 0: ap config |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.3.1.10 | ColumnqtechRrmAPIfNoiseGlobalConfig | read-write | current | Noise threshold inherited from global or not, 1: global config, 0: ap config |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.3.1.11 | ColumnqtechRrmAPIfRFUtilizationGlobalConfig | read-write | current | RFUtilization threshold inherited from global or not, 1: global config, 0: ap config |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.3.1.12 | ColumnqtechRrmAPIfThroughputGlobalConfig | read-write | current | Throughput threshold inherited from global or not, 1: global config, 0: ap config |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.3.1.13 | ColumnqtechRrmAPIfMobilesGlobalConfig | read-write | current | Mobiles threshold inherited from global or not, 1: global config, 0: ap config |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.4 | TableqtechRrmAPIfLoadParametersTable | not-accessible | current | These are RRM performance related read only parameters per Airespace AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.4.1 | RowqtechRrmAPIfLoadParametersEntry | not-accessible | current | An entry (conceptual row) in the Table. Entries in this MIB are indexed by qtechRrmAPDot3MacAddress and qtechRrmAPIfSlotId |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.4.1.1 | ColumnqtechRrmAPIfLoadRxUtilization | read-only | current | This is the percentage of time the Airespace AP receiver is busy operating on packets. It is a number from 0-100 representing a load from 0 to 1. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.4.1.2 | ColumnqtechRrmAPIfLoadTxUtilization | read-only | current | This is the percentage of time the Airespace AP transmitter is busy operating on packets. It is a number from 0-100 representing a load from 0 to 1. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.4.1.3 | ColumnqtechRrmAPIfLoadChannelUtilization | read-only | current | Channel Utilization |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.4.1.4 | ColumnqtechRrmAPIfLoadNumOfClients | read-only | current | This is the number of clients attached to this Airespace AP at the last measurement interval(This comes from APF) |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.4.1.5 | ColumnqtechRrmAPIfPoorSNRClients | read-only | current | This is the number of clients with poor SNR attached to this Airespace AP at the last measurement interval ( This comes from APF ). |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.4.1.6 | ColumnqtechRrmAPIfLoadName | read-only | current | The name of the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.4.1.7 | ColumnqtechRrmAPIfLoadMacAddr | read-only | current | The MAC address of radio on the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.4.1.8 | ColumnqtechRrmAPIfLoadSlotId | read-only | current | Number of Radio Interfaces on the Airespace AP. Currently maximum two interfaces are supported. One would be of type 802.11a and other of type 802.11b/g. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.4.1.9 | ColumnqtechRrmAPIfThroughput | read-only | current | Throughput in ap's radio, it represent the performance of ap |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.5 | TableqtechRrmAPIfChannelInterferenceInfoTable | not-accessible | current | This is a table of channel information like interference and noise from other 802.11 networks on each channel. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.5.1 | RowqtechRrmAPIfChannelInterferenceInfoEntry | not-accessible | current | An entry (conceptual row) in the Table. Entries in this MIB are indexed by qtechRrmAPDot3MacAddress, qtechRrmAPIfSlotId |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.5.1.1 | ColumnqtechRrmAPIfInterferenceChannelNo | read-only | current | Channel Number on AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.5.1.2 | ColumnqtechRrmAPIfInterferencePower | read-only | current | Power of Interference from other 802.11 networks on this channel |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.5.1.3 | ColumnqtechRrmAPIfInterferenceUtilization | read-only | current | Interference from other 802.11 networks on this channel |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.5.1.4 | ColumnqtechRrmAPIfInterferenceName | read-only | current | The name of the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.5.1.5 | ColumnqtechRrmAPIfInterferenceMacAddr | read-only | current | The MAC address of radio on the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.5.1.6 | ColumnqtechRrmAPIfInterferenceSlotId | read-only | current | Number of Radio Interfaces on the Airespace AP. Currently maximum two interfaces are supported. One would be of type 802.11a and other of type 802.11b/g. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.6 | TableqtechRrmAPIfChannelNoiseInfoTable | not-accessible | current | This is a table of channel information like interference and noise from other 802.11 networks on each channel. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.6.1 | RowqtechRrmAPIfChannelNoiseInfoEntry | not-accessible | current | An entry (conceptual row) in the Table. Entries in this MIB are indexed by qtechRrmAPDot3MacAddress, qtechRrmAPIfSlotId |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.6.1.1 | ColumnqtechRrmAPIfNoiseChannelNo | read-only | current | Channel Number on AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.6.1.2 | ColumnqtechRrmAPIfDBNoisePower | read-only | current | This is the average noise power in dBm on each channel that is available to Airespace AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.6.1.3 | ColumnqtechRrmAPIfNoiseName | read-only | current | The name of the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.6.1.4 | ColumnqtechRrmAPIfNoiseMacAddr | read-only | current | The MAC address of radio on the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.6.1.5 | ColumnqtechRrmAPIfNoiseSlotId | read-only | current | Number of Radio Interfaces on the Airespace AP. Currently maximum two interfaces are supported. One would be of type 802.11a and other of type 802.11b/g. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.7 | TableqtechRrmAPIfProfileStateTable | not-accessible | current | This is a table of state of interference monitor on each Airespace AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.7.1 | RowqtechRrmAPIfProfileStateEntry | not-accessible | current | An entry (conceptual row) in the Table. Entries in this MIB are indexed by qtechRrmAPDot3MacAddress, qtechRrmAPIfSlotId |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.7.1.1 | ColumnqtechRrmAPIfLoadProfileState | read-only | current | This field represents the current state of the LOAD monitor. This is a total measurement of the business of this Airespace AP. PASS indicates that this Airespa… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.7.1.2 | ColumnqtechRrmAPIfInterferenceProfileState | read-only | current | This field represents the current state of Interference monitor. This is a total measurement of the interference present at this Airespace AP. PASS indicates t… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.7.1.3 | ColumnqtechRrmAPIfNoiseProfileState | read-only | current | This field represents the current state of Noise monitor. This is a total measurement of the noise present at this Airespace AP. PASS indicates that this Aires… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.7.1.4 | ColumnqtechRrmAPIfCoverageProfileState | read-only | current | This field represents the current state of coverage monitor. This is a total measurement of the client coverage at this Airespace AP. PASS indicates that this … |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.7.1.5 | ColumnqtechRrmAPIfPerformanceProfileState | read-only | current | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.7.1.6 | ColumnqtechRrmAPIfProfileName | read-only | current | The name of the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.7.1.7 | ColumnqtechRrmAPIfProfileMacAddr | read-only | current | The MAC address of radio on the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.7.1.8 | ColumnqtechRrmAPIfProfileSlotId | read-only | current | Number of Radio Interfaces on the Airespace AP. Currently maximum two interfaces are supported. One would be of type 802.11a and other of type 802.11b/g. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.8 | TableqtechRrmAPIfRxNeighborsTable | not-accessible | current | This is a table of Rx Neighbors for each Airespace AP with their RSSI value. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.8.1 | RowqtechRrmAPIfRxNeighborsEntry | not-accessible | current | An entry (conceptual row) in the Table. Entries in this MIB are indexed by qtechRrmAPDot3MacAddress qtechRrmAPIfSlotId, qtechRrmAPIfRxNeighborMacAddress |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.8.1.1 | ColumnqtechRrmAPIfRxNeighborMacAddress | read-only | current | MAC Address of Rx Neighbor of the Airespace AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.8.1.2 | ColumnqtechRrmAPIfRxNeighborSlot | read-only | current | Slot value of the Rx Neighbor |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.8.1.3 | ColumnqtechRrmAPIfRxNeighborIpAddress | read-only | current | IP Address of Rx Neighbor of the Airespace AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.8.1.4 | ColumnqtechRrmAPIfRxNeighborRSSI | read-only | current | RSSI value of the Rx Neighbor |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.8.1.5 | ColumnqtechRrmAPIfRxNeighborSNR | read-only | current | SNR value of the Rx Neighbor |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.8.1.6 | ColumnqtechRrmAPIfRxNeighborChannel | read-only | current | This object represents Channel information which neighboring Access point is using. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.8.1.7 | ColumnqtechRrmAPIfRxNeighborChannelWidth | read-only | current | This object represents Channel bandwidth information which neighboring Access point is using. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.8.1.8 | ColumnqtechRrmAPIfRxNeighborName | read-only | current | The name of the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.8.1.9 | ColumnqtechRrmAPIfRxNeighborMacAddr | read-only | current | The MAC address of radio on the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.8.1.10 | ColumnqtechRrmAPIfRxNeighborSlotId | read-only | current | Number of Radio Interfaces on the Airespace AP. Currently maximum two interfaces are supported. One would be of type 802.11a and other of type 802.11b/g. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.9 | TableqtechRrmAPIfStationRSSICoverageInfoTable | not-accessible | current | This is a table of channel information like interference and noise from other 802.11 networks on each channel. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.9.1 | RowqtechRrmAPIfStationRSSICoverageInfoEntry | not-accessible | current | An entry (conceptual row) in the Table. Entries in this MIB are indexed by qtechRrmAPDot3MacAddress, qtechRrmAPIfSlotId |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.9.1.1 | ColumnqtechRrmAPIfStationRSSICoverageIndex | read-only | current | RSSI Coverage Index on AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.9.1.2 | ColumnqtechRrmAPIfRSSILevel | read-only | current | RSSI Level |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.9.1.3 | ColumnqtechRrmAPIfStationCountOnRSSI | read-only | current | Number of stations on this RSSI Level |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.9.1.4 | ColumnqtechRrmAPIfStationRSSIName | read-only | current | The name of the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.9.1.5 | ColumnqtechRrmAPIfStationRSSIMacAddr | read-only | current | The MAC address of radio on the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.9.1.6 | ColumnqtechRrmAPIfStationRSSISlotId | read-only | current | Number of Radio Interfaces on the Airespace AP. Currently maximum two interfaces are supported. One would be of type 802.11a and other of type 802.11b/g. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.10 | TableqtechRrmAPIfStationSNRCoverageInfoTable | not-accessible | current | This is a table of Signal to Noise ratio Coverage information on an AP Interface. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.10.1 | RowqtechRrmAPIfStationSNRCoverageInfoEntry | not-accessible | current | An entry (conceptual row) in the Table. Entries in this MIB are indexed by qtechRrmAPDot3MacAddress, qtechRrmAPIfSlotId |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.10.1.1 | ColumnqtechRrmAPIfStationSNRCoverageIndex | read-only | current | SNR Coverage Index on AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.10.1.2 | ColumnqtechRrmAPIfSNRLevel | read-only | current | SNR Level |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.10.1.3 | ColumnqtechRrmAPIfStationCountOnSNR | read-only | current | Number of stations on this SNR Level |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.10.1.4 | ColumnqtechRrmAPIfStationSNRName | read-only | current | The name of the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.10.1.5 | ColumnqtechRrmAPIfStationSNRMacAddr | read-only | current | The MAC address of radio on the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.10.1.6 | ColumnqtechRrmAPIfStationSNRSlotId | read-only | current | Number of Radio Interfaces on the Airespace AP. Currently maximum two interfaces are supported. One would be of type 802.11a and other of type 802.11b/g. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.11 | TableqtechRrmAPIfRecommendedRFParametersTable | not-accessible | current | This table list Best Channel,Best TxPowerLevel, Best RTSThreshold,Best FragmentationThreshold etc for this AP Interface as determined by RRM. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.11.1 | RowqtechRrmAPIfRecommendedRFParametersEntry | not-accessible | current | An entry (conceptual row) in the Table. Entries in this MIB are indexed by qtechRrmAPDot3MacAddress, qtechRrmAPIfSlotId |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.11.1.1 | ColumnqtechRrmAPIfRecommendedChannelNumber | read-only | current | Recommended ChannelNumber by RRM for this APIf |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.11.1.2 | ColumnqtechRrmAPIfRecommendedTxPowerLevel | read-only | current | Recommended TxPowerLevel by RRM for this APIf |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.11.1.3 | ColumnqtechRrmAPIfRecommendedRTSThreshold | read-only | current | Recommended RTSThreshold by RRM for this APIf |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.11.1.4 | ColumnqtechRrmAPIfRecommendedFragmentationThreshold | read-only | current | Recommended Fragmentation Threshold by RRM for this APIf |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.11.1.5 | ColumnqtechRrmAPIfRecommendedName | read-only | current | The name of the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.11.1.6 | ColumnqtechRrmAPIfRecommendedMacAddr | read-only | current | The MAC address of radio on the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.11.1.7 | ColumnqtechRrmAPIfRecommendedSlotId | read-only | current | Number of Radio Interfaces on the Airespace AP. Currently maximum two interfaces are supported. One would be of type 802.11a and other of type 802.11b/g. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.12 | TableqtechRrmAPRadioTable | not-accessible | current | ap radio table |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.12.1 | RowqtechRrmAPRadioEntry | not-accessible | current | all radio in aps |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.12.1.1 | ColumnqtechRrmAPRadioID | read-only | current | Number of Radio Interfaces on the Qtech AP. Currently maximum 32 interfaces are supported. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.12.1.2 | ColumnqtechRrmAPRadioType | read-only | current | radio type, type 802.11b means 2.4GHz, type 802.11a means 5GHz, |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.12.1.3 | ColumnqtechRrmAPRealName | read-only | current | The name of the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.12.1.4 | ColumnqtechRrmAPMacAddr | read-only | current | The MAC address of radio on the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.13 | TableqtechRrmAPIfThroughputParametersTable | not-accessible | current | These are RRM performance related read only parameters per Airespace AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.13.1 | RowqtechRrmAPIfThroughputParametersEntry | not-accessible | current | An entry (conceptual row) in the Table. Entries in this MIB are indexed by qtechRrmAPDot3MacAddress and qtechRrmAPIfSlotId |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.13.1.1 | ColumnqtechRrmAPIfThroughputMacAddr | read-only | current | The MAC address of radio on the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.13.1.2 | ColumnqtechRrmAPIfThroughputSlotId | read-only | current | Number of Radio Interfaces on the Airespace AP. Currently maximum two interfaces are supported. One would be of type 802.11a and other of type 802.11b/g. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.13.1.3 | ColumnqtechRrmAPIfThroughputAPName | read-only | current | The name of the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.13.1.4 | ColumnqtechRrmAPIfThroughputRx | read-only | current | This is the RX throughput |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.13.1.5 | ColumnqtechRrmAPIfThroughputTx | read-only | current | This is the TX throughput |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.13.1.6 | ColumnqtechRrmAPIfThroughputTotal | read-only | current | This is the total throughput |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.14 | TableqtechRrmAPSnrBSSIDTable | not-accessible | current | These are stat on ap snr BSSID |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.14.1 | RowqtechRrmAPSnrBSSIDEntry | not-accessible | current | An entry (conceptual row) in the Table. Entries in this MIB are indexed by qtechRrmAPDot3MacAddress and qtechRrmAPIfSlotId |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.14.1.1 | ColumnqtechRrmAPSnrBSSIDMacAddr | read-only | current | The MAC address of radio on the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.14.1.2 | ColumnqtechRrmAPSnrBSSIDSlotId | read-only | current | Number of Radio Interfaces on the Airespace AP. Currently maximum two interfaces are supported. One would be of type 802.11a and other of type 802.11b/g. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.14.1.3 | ColumnqtechRrmAPSnrBSSIDAPName | read-only | current | The name of the AP |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.14.1.4 | ColumnqtechRrmAPSnrBSSIDAverageSignalStrength | read-only | current | The average signal strength during monitor |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.14.1.5 | ColumnqtechRrmAPSnrBSSIDSignalPkts | read-only | current | The number of signal packets |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.14.1.6 | ColumnqtechRrmAPSnrBSSIDHighestRxSignalStrength | read-only | current | The highest rx signal strength during monitor |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.14.1.7 | ColumnqtechRrmAPSnrBSSIDLowestRxSignalStrength | read-only | current | The lowest rx signal strength during monitor |
| 1.3.6.1.4.1.27514.1.1.10.2.63.1.4.14.1.8 | ColumnqtechRrmAPSnrBSSIDSampleTime | read-only | current | The sample time |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2 | NodeqtechRrmMIBTraps | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.1 | NodeqtechRrmTrapControl | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.1.1 | ScalarqtechRrmAPDot11bProfileTrapControlMask | read-write | current | This mask describes what events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event … |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.1.2 | ScalarqtechRrmAPDot11aProfileTrapControlMask | read-write | current | This mask describes what events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event … |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.1.3 | ScalarqtechRrmAPDot11bParamUpdateTrapControlMask | read-write | current | Mac Parameters are updated for a Qtech AP interface whenever Dynamic Algorithm are run. This mask describes what update events merit traps to network managemen… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.1.4 | ScalarqtechRrmAPDot11aParamUpdateTrapControlMask | read-write | current | Mac Parameters are updated for a Qtech AP interface whenever Dynamic Algorithm are run. This mask describes what update events merit traps to network managemen… |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.2 | NodeqtechRrmTrapVariable | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.2.1 | ScalarqtechRrmAPMacAddrTrapVariable | accessible-for-notify | current | the variable of ap radio MAC address in trap |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.2.2 | ScalarqtechRrmAPRadioIDTrapVariable | accessible-for-notify | current | the variable of radio id in trap |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.2.3 | ScalarqtechRrmAPRadioTypeTrapVariable | accessible-for-notify | current | the variable of radio type in trap |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.2.4 | ScalarqtechRrmClientNumberTrapVariable | accessible-for-notify | current | the variable of client number in trap |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.2.5 | ScalarqtechRrmForeignInterfereTrapVariable | accessible-for-notify | current | the variable of interference in trap |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.2.6 | ScalarqtechRrmNoiseTrapVariable | accessible-for-notify | current | the variable of noise in trap |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.2.7 | ScalarqtechRrmThroughputTrapVariable | accessible-for-notify | current | the variable of throughput in trap |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.2.8 | ScalarqtechRrmUtilizationTrapVariable | accessible-for-notify | current | the variable of utilization in trap |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.2.9 | ScalarqtechRrmAPTxPowerBeforeChange | accessible-for-notify | current | The txpower level before change |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.2.10 | ScalarqtechRrmAPTxPowerAfterChange | accessible-for-notify | current | The txpower level after change |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.2.11 | ScalarqtechRrmAPChannelNumberBeforeChannge | accessible-for-notify | current | The channel before change |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.2.12 | ScalarqtechRrmAPChannelNumberAfterChannge | accessible-for-notify | current | The channel after channge |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.2.13 | ScalarqtechRrmDot11bGroupLeaderMacAddrTrapVariable | accessible-for-notify | current | The MAC address of the group leader. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.2.14 | ScalarqtechRrmDot11aGroupLeaderMacAddrTrapVariable | accessible-for-notify | current | The MAC address of the group leader. |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.2.15 | ScalarqtechRrmAPChannelChangeReason | accessible-for-notify | current | The reason cause the channel changed |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.2.16 | ScalarqtechRrmAPChannelChangeReasonValue | accessible-for-notify | current | The special value along with the reason of channel change |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.2.17 | ScalarqtechRrmAPTxPowerChangeCoverageFlag | accessible-for-notify | current | Indication the power change cause by which algorithm, TPC Algorithm or CHD Algorithm |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.2.18 | ScalarqtechRrmDFSFreeCount | accessible-for-notify | current | Indication the number of channel usable |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.2.19 | ScalarqtechRrmAPChannelChangeCount | accessible-for-notify | current | the number of channel change |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.3 | NodeqtechRrmTraps | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.3.1 | NotificationqtechRrmAPClientNumProfileFailed | current | too many clients | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.3.2 | NotificationqtechRrmAPLoadProfileFailed | current | When LOAD Profile state changes from PASS to FAIL, notification will be sent with Dot3 MAC address of Qtech AP and slot ID of Qtech AP IF. This trap sending ca… | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.3.3 | NotificationqtechRrmAPNoiseProfileFailed | current | When Noise Profile state changes from PASS to FAIL, notification will be sent with Dot3 MAC address of Qtech AP and slot ID of Qtech AP IF. This trap sending c… | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.3.4 | NotificationqtechRrmAPInterferenceProfileFailed | current | When Interference Profile state changes from PASS to FAIL, notification will be sent with Dot3 MAC address of Qtech AP and slot ID of Qtech AP IF. This trap se… | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.3.5 | NotificationqtechRrmAPPerformanceProfileFailed | current | ||
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.3.6 | NotificationqtechRrmAPClientNumProfileUpdatedToPass | current | ||
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.3.7 | NotificationqtechRrmAPLoadProfileUpdatedToPass | current | When LOAD Profile state changes from FAIL to PASSt this notification will be sent with Dot3 MAC address of Qtech AP and slot ID of Qtech AP IF. This trap sendi… | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.3.8 | NotificationqtechRrmAPNoiseProfileUpdatedToPass | current | When Noise Profile state changes from FAIL tp PASS, notification will be sent with Dot3 MAC address of Qtech AP and slot ID of Qtech AP IF. This trap sending c… | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.3.9 | NotificationqtechRrmAPInterferenceProfileUpdatedToPass | current | When Interference Profile state changes from FAIL tp PASS, notification will be sent with Dot3 MAC address of Qtech AP and slot ID of Qtech AP IF. This trap se… | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.3.10 | NotificationqtechRrmAPPerformanceProfileUpdatedToPass | current | ||
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.3.11 | NotificationqtechRrmAPCurrentTxPowerChanged | current | Whenever dynamic algorithms are running and qtechRrmAPIfPhyPowerAutomaticOn is true, Qtech AP Interface's CurrentTxPower might get updated by algorithm. When t… | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.3.12 | NotificationqtechRrmAPCurrentChannelChanged | current | Whenever dynamic algorithms are running and qtechRrmAPIfPhyChannelAutomaticOn is true, Qtech AP Interface's CurrentChannel might get updated by algorithm. When… | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.3.13 | NotificationqtechRrmDot11bGroupingDone | current | When Grouping is done, this notification will be sent from the previous Group Leader where grouping algorithm was run. It has MAC address of the new Group Lead… | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.3.14 | NotificationqtechRrmDot11aGroupingDone | current | When Grouping is done, this notification will be sent from the previous Group Leader where grouping algorithm was run. It has MAC address of the new Group Lead… | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.3.15 | NotificationqtechRrmDot11bDFSFreeCountBelowThreshold | current | When the free channel in 802.11b DCA too few, this notification will be sent | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.3.16 | NotificationqtechRrmDot11aDFSFreeCountBelowThreshold | current | When the free channel in 802.11b DCA too few, this notification will be sent | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.3.17 | NotificationqtechRrmNeighborAPInterference | current | notice when find interference form neighbor AP | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.3.18 | NotificationqtechRrmStationInterference | current | notice when find interference form station | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.2.3.19 | NotificationqtechRrmOtherDiveceInterference | current | notice when find interference form other divece | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.3 | NodeqtechRrmMIBConformance | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.3.1 | NodeqtechRrmMIBCompliances | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.3.1.1 | ComplianceqtechRrmMIBCompliance | current | The compliance statement for entities which implement the Qtech RRM module | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.3.2 | NodeqtechRrmMIBGroups | |||
| 1.3.6.1.4.1.27514.1.1.10.2.63.3.2.1 | GroupqtechRrmMIBGroup | current | This collection of objects provide the information about Qtech Radio Resource Management Configuration Parameters. These objects are defined under qtechRrmRrm … | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.3.2.2 | GroupqtechRrmTrapsGroup | current | This collection of objects provide the information about Qtech Trap Configuration and Trap definition. These objects are defined under qtechRrmTrap. | |
| 1.3.6.1.4.1.27514.1.1.10.2.63.3.2.3 | GroupqtechRrmTrap | current | This collection of objects provides all notification that Switch need to generate to the Management System. |