RADWIN-MIB-WINLINK1000
402 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | Counter enterprises Gauge IpAddress TimeTicks |
| RFC1213-MIB | DisplayString ifIndex |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.4458 | Noderadwin | |||
| 1.3.6.1.4.1.4458.20 | NoderadwinProducts | |||
| 1.3.6.1.4.1.4458.20.2 | Nodewinlink1000Family | |||
| 1.3.6.1.4.1.4458.20.2.1 | Nodeodu | |||
| 1.3.6.1.4.1.4458.20.2.1.1 | NodeoduIntegratedAntenna | |||
| 1.3.6.1.4.1.4458.20.2.1.2 | NodeoduExternalAntenna | |||
| 1.3.6.1.4.1.4458.20.3 | Noderadwin2000Family | |||
| 1.3.6.1.4.1.4458.20.3.1 | Nodeodu2000 | |||
| 1.3.6.1.4.1.4458.20.3.1.1 | Nodeodu2KIntegratedAntenna | |||
| 1.3.6.1.4.1.4458.20.3.1.2 | Nodeodu2KExternalAntenna | |||
| 1.3.6.1.4.1.4458.20.4 | NodegpsSynchronizerFamily | |||
| 1.3.6.1.4.1.4458.20.4.1 | NodeoduGSU | |||
| 1.3.6.1.4.1.4458.20.4.1.2 | NodeoduGSUExternalAntenna | |||
| 1.3.6.1.4.1.4458.20.4.2 | NodehssSyncUnits | |||
| 1.3.6.1.4.1.4458.20.4.2.1 | NodehssISU | |||
| 1.3.6.1.4.1.4458.20.4.2.2 | NodehssGSU | |||
| 1.3.6.1.4.1.4458.20.5 | Noderadwin5000HBSFamily | |||
| 1.3.6.1.4.1.4458.20.5.1 | NodeoduHBS | |||
| 1.3.6.1.4.1.4458.20.5.1.1 | NodeoduHBSIntegratedAntenna | |||
| 1.3.6.1.4.1.4458.20.5.1.2 | NodeoduHBSExternalAntenna | |||
| 1.3.6.1.4.1.4458.20.6 | Noderadwin5000HSUFamily | |||
| 1.3.6.1.4.1.4458.20.6.1 | NodeoduHSU | |||
| 1.3.6.1.4.1.4458.20.6.1.1 | NodeoduHSUIntegratedAntenna | |||
| 1.3.6.1.4.1.4458.20.6.1.2 | NodeoduHSUExternalAntenna | |||
| 1.3.6.1.4.1.4458.20.10 | Noderadwin6000Family | |||
| 1.3.6.1.4.1.4458.20.10.1 | Nodeodu6000 | |||
| 1.3.6.1.4.1.4458.20.10.1.1 | Nodeodu6K | |||
| 1.3.6.1.4.1.4458.20.10.2 | Nodegateway6000 | |||
| 1.3.6.1.4.1.4458.20.10.2.1 | Nodegateway6K | |||
| 1.3.6.1.4.1.4458.20.20 | NoderadwinWiFiAPFamily | |||
| 1.3.6.1.4.1.4458.20.20.1 | Nodeodu600 | |||
| 1.3.6.1.4.1.4458.20.20.1.1 | NodeoduWiFiAP | |||
| 1.3.6.1.4.1.4458.1000 | Nodewinlink1000 | |||
| 1.3.6.1.4.1.4458.1000.1 | Nodewinlink1000Odu | |||
| 1.3.6.1.4.1.4458.1000.1.1 | Nodewinlink1000OduAdmin | |||
| 1.3.6.1.4.1.4458.1000.1.1.1 | Scalarwinlink1000OduAdmProductType | read-only | mandatory | ODU configuration description. |
| 1.3.6.1.4.1.4458.1000.1.1.2 | Scalarwinlink1000OduAdmHwRev | read-only | mandatory | ODU Hardware Version. |
| 1.3.6.1.4.1.4458.1000.1.1.3 | Scalarwinlink1000OduAdmSwRev | read-only | mandatory | ODU Software Version. |
| 1.3.6.1.4.1.4458.1000.1.1.4 | Scalarwinlink1000OduAdmLinkName | read-write | mandatory | Link Name. A change is effective immediately. |
| 1.3.6.1.4.1.4458.1000.1.1.5 | Scalarwinlink1000OduAdmResetCmd | read-write | mandatory | Reset Command. A set command with a value of 3 will cause a device reset. HBS only: A set command with a value of 4 will cause a device reset for the entire se… |
| 1.3.6.1.4.1.4458.1000.1.1.6 | Scalarwinlink1000OduAdmAddres | read-write | mandatory | ODU IP address. A change is effective after reset. The parameter is kept for backward compatibility. Using the alternative parameter: winlink1000OduAdmIpParams… |
| 1.3.6.1.4.1.4458.1000.1.1.7 | Scalarwinlink1000OduAdmMask | read-write | mandatory | ODU Subnet Mask. A change is effective after reset. The parameter is kept for backward compatibility. Using the alternative parameter: winlink1000OduAdmIpParam… |
| 1.3.6.1.4.1.4458.1000.1.1.8 | Scalarwinlink1000OduAdmGateway | read-write | mandatory | ODU default gateway. A change is effective after reset. The parameter is kept for backward compatibility. Using the alternative parameter: winlink1000OduAdmIpP… |
| 1.3.6.1.4.1.4458.1000.1.1.10 | Scalarwinlink1000OduAdmBroadcast | read-write | mandatory | This parameter is reserved for the Manager application provided with the product. |
| 1.3.6.1.4.1.4458.1000.1.1.12 | Tablewinlink1000OduAdmHostsTable | not-accessible | mandatory | Trap destinations table. Each trap destination is defined by an IP address and a UDP port. Up to 10 addresses can be configured. |
| 1.3.6.1.4.1.4458.1000.1.1.12.1 | Rowwinlink1000OduAdmHostsEntry | not-accessible | mandatory | Trap destinations table entry. |
| 1.3.6.1.4.1.4458.1000.1.1.12.1.1 | Columnwinlink1000OduAdmHostsIndex | read-only | mandatory | Trap destinations table index. |
| 1.3.6.1.4.1.4458.1000.1.1.12.1.2 | Columnwinlink1000OduAdmHostsIp | read-write | mandatory | Trap destination IP address. A change is effective immediately. |
| 1.3.6.1.4.1.4458.1000.1.1.12.1.3 | Columnwinlink1000OduAdmHostsPort | read-write | mandatory | UDP port of the trap destination. A change is effective immediately. |
| 1.3.6.1.4.1.4458.1000.1.1.12.1.4 | Columnwinlink1000OduAdmHostsSecurityModel | read-write | mandatory | Security model used for this trap generation. |
| 1.3.6.1.4.1.4458.1000.1.1.12.1.5 | Columnwinlink1000OduAdmHostsUserName | read-write | mandatory | User name used to generate the snmpv3 trap. |
| 1.3.6.1.4.1.4458.1000.1.1.12.1.6 | Columnwinlink1000OduAdmHostsPassword | read-write | mandatory | Password used to generate the snmpv3 trap. |
| 1.3.6.1.4.1.4458.1000.1.1.12.1.7 | Columnwinlink1000OduAdmHostsIPv6 | read-write | mandatory | Trap destination IPv6 address. A change is effective immediately. |
| 1.3.6.1.4.1.4458.1000.1.1.13 | Scalarwinlink1000OduBuzzerAdminState | read-write | mandatory | This parameter controls the activation of the buzzer while the unit is in install mode. A change is effective immediately. The valid values are: disabled (0), … |
| 1.3.6.1.4.1.4458.1000.1.1.14 | Scalarwinlink1000OduProductId | read-only | mandatory | This parameter is reserved for the Manager application provided with the product. |
| 1.3.6.1.4.1.4458.1000.1.1.15 | Scalarwinlink1000OduReadCommunity | read-write | mandatory | Read Community String. This parameter always returns ***** when retrieving its value. It is used by the Manager application to change the Read Community String… |
| 1.3.6.1.4.1.4458.1000.1.1.16 | Scalarwinlink1000OduReadWriteCommunity | read-write | mandatory | Read/Write Community String. This parameter always returns ***** when retrieving its value. It is used by the Manager application to change the Read/Write Comm… |
| 1.3.6.1.4.1.4458.1000.1.1.17 | Scalarwinlink1000OduTrapCommunity | read-write | mandatory | Trap Community String. This parameter is used by the Manager application to change the Trap Community String. The SNMP agent accepts only encrypted values. |
| 1.3.6.1.4.1.4458.1000.1.1.18 | Scalarwinlink1000OduAdmSnmpAgentVersion | read-only | mandatory | Major version of the SNMP agent. |
| 1.3.6.1.4.1.4458.1000.1.1.19 | Scalarwinlink1000OduAdmRemoteSiteName | read-only | mandatory | Remote site name. Returns the same value as sysLocation parameter of the remote site. |
| 1.3.6.1.4.1.4458.1000.1.1.20 | Scalarwinlink1000OduAdmSnmpAgentMinorVersion | read-only | mandatory | Minor version of the SNMP agent. |
| 1.3.6.1.4.1.4458.1000.1.1.21 | Scalarwinlink1000OduAdmLinkPassword | read-write | mandatory | Link Password. This parameter always returns ***** when retrieving its value. It is used by the Manager application to change the Link Password. The SNMP agent… |
| 1.3.6.1.4.1.4458.1000.1.1.22 | Scalarwinlink1000OduAdmSiteLinkPassword | read-write | mandatory | Site Link Password. This parameter always returns ***** when retrieving its value. It is used by the Manager application to change the Link Password of the sit… |
| 1.3.6.1.4.1.4458.1000.1.1.23 | Scalarwinlink1000OduAdmDefaultPassword | read-only | mandatory | This parameter indicates if the current Link Password is the default password. |
| 1.3.6.1.4.1.4458.1000.1.1.24 | Scalarwinlink1000OduAdmConnectionType | read-only | mandatory | This parameter indicates if the Manager application is connected to the local ODU or to the remote ODU over the air. A value of 'unknown' indicates community s… |
| 1.3.6.1.4.1.4458.1000.1.1.25 | Scalarwinlink1000OduAdmBackToFactorySettingsCmd | read-write | mandatory | Back to factory settings Command. A change is effective after reset. The read value is always 0. |
| 1.3.6.1.4.1.4458.1000.1.1.26 | Scalarwinlink1000OduAdmIpParamsCnfg | read-write | mandatory | ODU IP address Configuration. The format is: ||| |
| 1.3.6.1.4.1.4458.1000.1.1.27 | Scalarwinlink1000OduAdmVlanID | read-write | mandatory | VLAN ID. Valid values are 1 to 4094. Initial value is 0 meaning VLAN unaware. |
| 1.3.6.1.4.1.4458.1000.1.1.28 | Scalarwinlink1000OduAdmVlanPriority | read-write | mandatory | VLAN Priority. 0 is lowest priority, 7 is highest priority. |
| 1.3.6.1.4.1.4458.1000.1.1.29 | Scalarwinlink1000OduAdmSN | read-only | mandatory | ODU Serial Number |
| 1.3.6.1.4.1.4458.1000.1.1.30 | Scalarwinlink1000OduAdmProductName | read-only | mandatory | This is the product name as it exists at EC |
| 1.3.6.1.4.1.4458.1000.1.1.31 | Scalarwinlink1000OduAdmActivationKey | read-write | mandatory | Activates a general key. |
| 1.3.6.1.4.1.4458.1000.1.1.32 | Scalarwinlink1000OduAdmRmtPermittedOduType | read-write | mandatory | Mobile Application: permitted partner OduType. |
| 1.3.6.1.4.1.4458.1000.1.1.33 | Scalarwinlink1000OduAdmCpuID | read-only | mandatory | CPU ID |
| 1.3.6.1.4.1.4458.1000.1.1.34 | Scalarwinlink1000OduAdmOvrdCmd | read-write | mandatory | Ability to perform special command in the ODU. |
| 1.3.6.1.4.1.4458.1000.1.1.35 | Scalarwinlink1000OduAdmLinkMode | read-write | mandatory | Unit PMP operation mode. |
| 1.3.6.1.4.1.4458.1000.1.1.36 | Scalarwinlink1000OduAdmActualConnectMode | read-only | mandatory | Unit connected as part to ptp or ptmp. |
| 1.3.6.1.4.1.4458.1000.1.1.37 | Scalarwinlink1000OduAdmAES256Support | read-only | mandatory | AES-256 security support indication. |
| 1.3.6.1.4.1.4458.1000.1.1.38 | Scalarwinlink1000OduAdmAES256State | read-write | mandatory | Enable/Disable AES-256 security mode over the air link. |
| 1.3.6.1.4.1.4458.1000.1.1.39 | Scalarwinlink1000OduAdmAES256Status | read-only | mandatory | AES256 operating status |
| 1.3.6.1.4.1.4458.1000.1.1.40 | Scalarwinlink1000OduAdmBatterySavingShutdownTime | read-write | mandatory | Battery Saving Shutdown Time in minutes, 0 till battery run out, -1 if not supported. |
| 1.3.6.1.4.1.4458.1000.1.1.41 | Scalarwinlink1000OduAdmWiFiPowerMode | read-write | mandatory | WIFI unit power mode. |
| 1.3.6.1.4.1.4458.1000.1.1.42 | Scalarwinlink1000OduAdmShutdownTimer | read-only | mandatory | Shutdown Timer in seconds. |
| 1.3.6.1.4.1.4458.1000.1.1.43 | Scalarwinlink1000OduAdmGPSState | read-only | mandatory | GPS state |
| 1.3.6.1.4.1.4458.1000.1.1.44 | Scalarwinlink1000OduAdmTemperatureC | read-only | mandatory | The temperature (Celsius) inside the Board. |
| 1.3.6.1.4.1.4458.1000.1.1.45 | Scalarwinlink1000OduAdmIPStackMode | read-write | mandatory | The IP stack mode. |
| 1.3.6.1.4.1.4458.1000.1.1.46 | Scalarwinlink1000OduAdmIPv6ParamsCnfg | read-write | mandatory | ODU IPv6 address Configuration. The format is: ||| |
| 1.3.6.1.4.1.4458.1000.1.1.47 | Scalarwinlink1000OduAdmIPv6Address | read-only | mandatory | ODU IPv6 address. |
| 1.3.6.1.4.1.4458.1000.1.1.48 | Scalarwinlink1000OduAdmIPv6Prefix | read-only | mandatory | ODU IPv6 subnet mask. |
| 1.3.6.1.4.1.4458.1000.1.1.49 | Scalarwinlink1000OduAdmIPv6DefaultGateWay | read-only | mandatory | ODU IPv6 default gateway. |
| 1.3.6.1.4.1.4458.1000.1.1.50 | Scalarwinlink1000OduAdmPowerConsumption | read-only | mandatory | Power Consumption (mWatt) |
| 1.3.6.1.4.1.4458.1000.1.1.51 | Nodewinlink1000OduAdmWifi | |||
| 1.3.6.1.4.1.4458.1000.1.1.51.1 | Scalarwinlink1000OduAdmWifiChannel | read-write | mandatory | Wifi Channel |
| 1.3.6.1.4.1.4458.1000.1.1.51.2 | Scalarwinlink1000OduAdmWifiTxPower | read-write | mandatory | Wifi TX Power |
| 1.3.6.1.4.1.4458.1000.1.1.51.3 | Scalarwinlink1000OduAdmWifiSSID | read-only | mandatory | Wifi SSID |
| 1.3.6.1.4.1.4458.1000.1.1.51.4 | Scalarwinlink1000OduAdmWifiSecurityType | read-only | mandatory | Wifi Security type |
| 1.3.6.1.4.1.4458.1000.1.1.51.5 | Scalarwinlink1000OduAdmWifiPassword | read-write | mandatory | Wifi Password |
| 1.3.6.1.4.1.4458.1000.1.1.51.6 | Scalarwinlink1000OduAdmWifiNetwork | read-write | mandatory | Wifi Network |
| 1.3.6.1.4.1.4458.1000.1.1.51.7 | Scalarwinlink1000OduAdmWifiRssi | read-only | mandatory | Wifi RSSI |
| 1.3.6.1.4.1.4458.1000.1.1.51.8 | Scalarwinlink1000OduAdmWifiStationMAC | read-only | mandatory | Wifi Station MAC |
| 1.3.6.1.4.1.4458.1000.1.1.51.9 | Scalarwinlink1000OduAdmWifiRestart | read-write | mandatory | A set command with a value of 1 will cause a Wifi restart. The read value is always 0. |
| 1.3.6.1.4.1.4458.1000.1.1.51.10 | Scalarwinlink1000OduAdmWifiApStatus | read-only | mandatory | Wifi AP Status |
| 1.3.6.1.4.1.4458.1000.1.1.52 | Scalarwinlink1000OduAdmBsaOperationMode | read-only | mandatory | BSA Operation Mode |
| 1.3.6.1.4.1.4458.1000.1.1.53 | Scalarwinlink1000OduAdmMngConnection | read-write | mandatory | Management Connection |
| 1.3.6.1.4.1.4458.1000.1.1.54 | Scalarwinlink1000OduAdm1588TCSupport | read-only | mandatory | Indicates that 1588TC license activated |
| 1.3.6.1.4.1.4458.1000.1.1.55 | Scalarwinlink1000OduAdmSyncESupport | read-only | mandatory | ndicates that SyncE license activated |
| 1.3.6.1.4.1.4458.1000.1.1.56 | Scalarwinlink1000OduAdmRadioRev | read-only | mandatory | Radio Revision |
| 1.3.6.1.4.1.4458.1000.1.1.57 | Scalarwinlink1000OduAdmProductRev | read-only | mandatory | Product Revision |
| 1.3.6.1.4.1.4458.1000.1.1.58 | Scalarwinlink1000OduAdmPMPSUSupport | read-only | mandatory | Indicates that PMP SU license is activated |
| 1.3.6.1.4.1.4458.1000.1.1.59 | Scalarwinlink1000OduAdmManagerDownloadURL | read-write | mandatory | This is the URL from which management tool can be downloaded |
| 1.3.6.1.4.1.4458.1000.1.1.60 | Scalarwinlink1000OduAdmAntennaDescription | read-only | mandatory | The is a description of the antenna connected to the ODU |
| 1.3.6.1.4.1.4458.1000.1.1.61 | Scalarwinlink1000OduAdmSwCapabilities | read-only | mandatory | This is used to describe which Software Capabilities the current ODU supports |
| 1.3.6.1.4.1.4458.1000.1.2 | Nodewinlink1000OduService | |||
| 1.3.6.1.4.1.4458.1000.1.2.1 | Scalarwinlink1000OduSrvMode | read-write | mandatory | System mode. The only values that can be set are installMode and slaveMode; normalMode reserved to the Manager application provided with the product. A change … |
| 1.3.6.1.4.1.4458.1000.1.2.3 | Scalarwinlink1000OduSrvBridging | read-only | mandatory | Bridging Mode. Valid values are: disabled (0), enabled (1). |
| 1.3.6.1.4.1.4458.1000.1.2.4 | Nodewinlink1000OduServiceRingTopology | |||
| 1.3.6.1.4.1.4458.1000.1.2.4.1 | Scalarwinlink1000OduSrvRingLinkMode | read-write | mandatory | Mode of the link regarding ring topology. |
| 1.3.6.1.4.1.4458.1000.1.2.4.2 | Scalarwinlink1000OduSrvRingTopologySupported | read-only | mandatory | Ring Topology, options are: supported, not supported |
| 1.3.6.1.4.1.4458.1000.1.2.4.3 | Tablewinlink1000OduSrvRingVlanIdTable | not-accessible | mandatory | Ring VLAN IDs table. |
| 1.3.6.1.4.1.4458.1000.1.2.4.3.1 | Rowwinlink1000OduSrvRingVlanIdEntry | not-accessible | mandatory | VLAN ID of the internal ring messages. Valid values are 1 to 4094. Initial value is 0 meaning VLAN unaware. |
| 1.3.6.1.4.1.4458.1000.1.2.4.3.1.1 | Columnwinlink1000OduSrvRingVlanIdIndex | read-only | mandatory | Index of VLAN ID of the internal ring messages. |
| 1.3.6.1.4.1.4458.1000.1.2.4.3.1.2 | Columnwinlink1000OduSrvRingVlanId | read-write | mandatory | VLAN ID of the internal ring messages. Valid values are 1 to 4094. Initial value is 0 meaning VLAN unaware. |
| 1.3.6.1.4.1.4458.1000.1.2.4.4 | Scalarwinlink1000OduSrvRingEthStatus | read-only | mandatory | Represents the Ethernet service blocking state of a Rings link |
| 1.3.6.1.4.1.4458.1000.1.2.4.5 | Scalarwinlink1000OduSrvRingMaxAllowedTimeFromLastRpm | read-write | mandatory | Defines the minimal time (in ms) required for determination of ring failure. |
| 1.3.6.1.4.1.4458.1000.1.2.4.6 | Scalarwinlink1000OduSrvRingWTR | read-write | mandatory | Defines the minimal time (in ms) required for ring recovery. |
| 1.3.6.1.4.1.4458.1000.1.2.5 | Nodewinlink1000OduServiceQoS | |||
| 1.3.6.1.4.1.4458.1000.1.2.5.1 | Scalarwinlink1000OduSrvQoSMode | read-write | mandatory | Mode of QoS feature. |
| 1.3.6.1.4.1.4458.1000.1.2.5.2 | Tablewinlink1000OduSrvQoSConfTable | not-accessible | mandatory | QoS configuration table. |
| 1.3.6.1.4.1.4458.1000.1.2.5.2.1 | Rowwinlink1000OduSrvQoSConfEntry | not-accessible | mandatory | QoS configuration table. |
| 1.3.6.1.4.1.4458.1000.1.2.5.2.1.1 | Columnwinlink1000OduSrvQoSConfIndex | read-only | mandatory | Index of QoS Configuration. |
| 1.3.6.1.4.1.4458.1000.1.2.5.2.1.2 | Columnwinlink1000OduSrvConfVlanQGroups | read-only | mandatory | Frames classification according to VLAN Priority IDs. |
| 1.3.6.1.4.1.4458.1000.1.2.5.2.1.3 | Columnwinlink1000OduSrvConfDiffservQGroups | read-only | mandatory | Frames classification according to Diffserv. |
| 1.3.6.1.4.1.4458.1000.1.2.5.2.1.4 | Columnwinlink1000OduSrvConfQueMir | read-write | mandatory | Desired Private MIR. |
| 1.3.6.1.4.1.4458.1000.1.2.5.2.1.5 | Columnwinlink1000OduSrvConfQueWeight | read-write | mandatory | QoS queueu's weights in percent. |
| 1.3.6.1.4.1.4458.1000.1.2.5.3 | Scalarwinlink1000OduSrvQoSVlanQGroupsSetStr | read-write | mandatory | Frames classification according to VLAN IDs string for set. |
| 1.3.6.1.4.1.4458.1000.1.2.5.4 | Scalarwinlink1000OduSrvQoSDiffservQGroupsSetStr | read-write | mandatory | Frames classification according to Diffserv IDs string for set. |
| 1.3.6.1.4.1.4458.1000.1.2.5.5 | Scalarwinlink1000OduSrvQoSMaxRTQuePercent | read-only | mandatory | Maximal percent for RT & NRT queues. |
| 1.3.6.1.4.1.4458.1000.1.2.6 | Nodewinlink1000OduServiceVlan | |||
| 1.3.6.1.4.1.4458.1000.1.2.6.1 | Scalarwinlink1000OduSrvVlanSupport | read-only | mandatory | ODU Ethernet port VLAN support and configuration availability indication. 1 - ODU VLAN Functionality Not Supported 2 - ODU VLAN Functionality Supported 3 - ODU… |
| 1.3.6.1.4.1.4458.1000.1.2.6.2 | Scalarwinlink1000OduSrvVlanIngressMode | read-write | mandatory | ODU Ethernet port ingress VLAN mode. |
| 1.3.6.1.4.1.4458.1000.1.2.6.3 | Scalarwinlink1000OduSrvVlanEgressMode | read-write | mandatory | ODU Ethernet port egress VLAN mode. |
| 1.3.6.1.4.1.4458.1000.1.2.6.4 | Scalarwinlink1000OduSrvEgressTag | read-write | mandatory | ODU ethernet port egress VLAN tag. Right most digit is Vlan priority (0-7), other digits compose Vlan Id (2-4094) |
| 1.3.6.1.4.1.4458.1000.1.2.6.5 | Scalarwinlink1000OduSrvEgressProviderTag | read-write | mandatory | ODU ethernet port egress Provider VLAN tag. Right most digit is Vlan priority (0-7), other digits compose Vlan Id (2-4094) |
| 1.3.6.1.4.1.4458.1000.1.2.6.6 | Scalarwinlink1000OduSrvVlanIngressAllowedVIDs | read-write | mandatory | ODU ethernet port VLAN IDs that will not be filtered on ingress. w|w|w|w|w|w|w|w| ( where w = {0-4094} and w != 1 ) |
| 1.3.6.1.4.1.4458.1000.1.2.6.7 | Scalarwinlink1000OduSrvVlanDisable | read-write | mandatory | Disable VLAN functionality. The following values can be set: 3 - Disable ODU & IDU VLAN Configurations. |
| 1.3.6.1.4.1.4458.1000.1.2.6.8 | Scalarwinlink1000OduServiceVlanProviderListTPIDstr | read-only | mandatory | Holds the possible Provider TPIDs. |
| 1.3.6.1.4.1.4458.1000.1.3 | Nodewinlink1000OduEthernet | |||
| 1.3.6.1.4.1.4458.1000.1.3.1 | Scalarwinlink1000OduEthernetRemainingRate | read-only | mandatory | Current Ethernet bandwidth in bps. |
| 1.3.6.1.4.1.4458.1000.1.3.2 | Tablewinlink1000OduEthernetIfTable | not-accessible | mandatory | ODU Ethernet Interface table. |
| 1.3.6.1.4.1.4458.1000.1.3.2.1 | Rowwinlink1000OduEthernetIfEntry | not-accessible | mandatory | ODU Ethernet Interface table entry. |
| 1.3.6.1.4.1.4458.1000.1.3.2.1.1 | Columnwinlink1000OduEthernetIfIndex | read-only | mandatory | ODU Ethernet Interface Index. |
| 1.3.6.1.4.1.4458.1000.1.3.2.1.5 | Columnwinlink1000OduEthernetIfAddress | read-only | mandatory | ODU MAC address. |
| 1.3.6.1.4.1.4458.1000.1.3.2.1.6 | Columnwinlink1000OduEthernetIfAdminStatus | read-write | mandatory | Required state of the interface. |
| 1.3.6.1.4.1.4458.1000.1.3.2.1.7 | Columnwinlink1000OduEthernetIfOperStatus | read-only | mandatory | Current operational state of the interface. |
| 1.3.6.1.4.1.4458.1000.1.3.2.1.8 | Columnwinlink1000OduEthernetIfFailAction | read-write | mandatory | Failure action of the interface. |
| 1.3.6.1.4.1.4458.1000.1.3.2.1.9 | Columnwinlink1000OduEthernetIf1588v2PTPEventRXRate | read-only | mandatory | For debug use |
| 1.3.6.1.4.1.4458.1000.1.3.2.1.10 | Columnwinlink1000OduEthernetIf1588v2PTPEventTXRate | read-only | mandatory | For debug use |
| 1.3.6.1.4.1.4458.1000.1.3.3 | Scalarwinlink1000OduEthernetNumOfPorts | read-only | mandatory | Number of ODU network interfaces. |
| 1.3.6.1.4.1.4458.1000.1.3.4 | Scalarwinlink1000OduEthernetGbeSupported | read-only | mandatory | Supported Giga bit Ethernet in ODU. |
| 1.3.6.1.4.1.4458.1000.1.3.5 | Scalarwinlink1000OduEthernetSfpProperties | read-only | mandatory | Sfp port properties. |
| 1.3.6.1.4.1.4458.1000.1.4 | Nodewinlink1000OduBridge | |||
| 1.3.6.1.4.1.4458.1000.1.4.1 | Nodewinlink1000OduBridgeBase | |||
| 1.3.6.1.4.1.4458.1000.1.4.1.4 | Tablewinlink1000OduBridgeBasePortTable | not-accessible | mandatory | ODU Bridge Ports table. |
| 1.3.6.1.4.1.4458.1000.1.4.1.4.1 | Rowwinlink1000OduBridgeBasePortEntry | not-accessible | mandatory | ODU Bridge Ports table entry. |
| 1.3.6.1.4.1.4458.1000.1.4.1.4.1.1 | Columnwinlink1000OduBridgeBasePortIndex | read-only | mandatory | ODU Bridge Port Number. |
| 1.3.6.1.4.1.4458.1000.1.4.1.4.1.2 | Columnwinlink1000OduBridgeBaseIfIndex | read-only | mandatory | IfIndex corresponding to ODU Bridge port. |
| 1.3.6.1.4.1.4458.1000.1.4.4 | Nodewinlink1000OduBridgeTp | |||
| 1.3.6.1.4.1.4458.1000.1.4.4.3 | Tablewinlink1000OduBridgeTpPortTable | not-accessible | mandatory | ODU Transparent Bridge Ports table. |
| 1.3.6.1.4.1.4458.1000.1.4.4.3.1 | Rowwinlink1000OduBridgeTpPortEntry | not-accessible | mandatory | ODU Transparent Bridge Ports table entry. |
| 1.3.6.1.4.1.4458.1000.1.4.4.3.1.1 | Columnwinlink1000OduBridgeTpPortIndex | read-only | mandatory | ODU Transparent Bridge Port Number. |
| 1.3.6.1.4.1.4458.1000.1.4.4.3.1.3 | Columnwinlink1000OduBridgeTpPortInFrames | read-only | mandatory | Number of frames received by this port. |
| 1.3.6.1.4.1.4458.1000.1.4.4.3.1.4 | Columnwinlink1000OduBridgeTpPortOutFrames | read-only | mandatory | Number of frames transmitted by this port. |
| 1.3.6.1.4.1.4458.1000.1.4.4.3.1.101 | Columnwinlink1000OduBridgeTpPortInBytes | read-only | mandatory | Number of bytes received by this port. |
| 1.3.6.1.4.1.4458.1000.1.4.4.3.1.102 | Columnwinlink1000OduBridgeTpPortOutBytes | read-only | mandatory | Number of bytes transmitted by this port. |
| 1.3.6.1.4.1.4458.1000.1.4.4.101 | Scalarwinlink1000OduBridgeTpMode | read-write | mandatory | ODU bridge mode. A change is effective after reset. Valid values: hubMode (0), bridgeMode (1). |
| 1.3.6.1.4.1.4458.1000.1.4.4.102 | Scalarwinlink1000OduBridgeConfigMode | read-only | mandatory | ODU bridge configuration mode |
| 1.3.6.1.4.1.4458.1000.1.5 | Nodewinlink1000OduAir | |||
| 1.3.6.1.4.1.4458.1000.1.5.1 | Scalarwinlink1000OduAirFreq | read-write | mandatory | Installation Center Frequency. Valid values are product dependent. A change is effective after link re-synchronization. |
| 1.3.6.1.4.1.4458.1000.1.5.2 | Scalarwinlink1000OduAirDesiredRate | read-write | deprecated | Deprecated parameter, actual behavior is read-only. Required Air Rate. For Channel Bandwidth of 20, 10, 5 MHz divide the value by 1, 2, 4 respectively. |
| 1.3.6.1.4.1.4458.1000.1.5.3 | Scalarwinlink1000OduAirSSID | read-write | mandatory | Reserved for the Manager application provided with the product. The Sector ID in Point-To-Multi-Point systems. |
| 1.3.6.1.4.1.4458.1000.1.5.4 | Scalarwinlink1000OduAirTxPower | read-write | mandatory | Required Transmit power in dBm . This is a nominal value while the actual transmit power includes additional attenuation. The min and max values are product sp… |
| 1.3.6.1.4.1.4458.1000.1.5.5 | Scalarwinlink1000OduAirSesState | read-only | mandatory | Current Link State. The value is active (3) during normal operation. |
| 1.3.6.1.4.1.4458.1000.1.5.6 | Scalarwinlink1000OduAirMstrSlv | read-only | mandatory | This parameter indicates if the device was automatically selected into the radio link master or slave. The value is undefined if there is no link. The value is… |
| 1.3.6.1.4.1.4458.1000.1.5.8 | Scalarwinlink1000OduAirResync | read-write | mandatory | Setting this parameter to 1 will cause the link to restart the synchronization process. |
| 1.3.6.1.4.1.4458.1000.1.5.9 | Nodewinlink1000OduAirPerf | |||
| 1.3.6.1.4.1.4458.1000.1.5.9.1 | Scalarwinlink1000OduAirRxPower | read-only | mandatory | Received Signal Strength in dBm. Relevant only for point to point systems. |
| 1.3.6.1.4.1.4458.1000.1.5.9.2 | Scalarwinlink1000OduAirTotalFrames | read-only | mandatory | Total number of radio frames. |
| 1.3.6.1.4.1.4458.1000.1.5.9.3 | Scalarwinlink1000OduAirBadFrames | read-only | mandatory | Total number of received radio frames with CRC error. The value is relevant only for point to point systems . |
| 1.3.6.1.4.1.4458.1000.1.5.9.4 | Scalarwinlink1000OduAirCurrentRate | read-only | deprecated | Deprecated parameter. Actual rate of the air interface in Mbps. For Channel Bandwidth of 20, 10, 5 MHz divide the value by 1, 2, 4 respectively. |
| 1.3.6.1.4.1.4458.1000.1.5.9.5 | Scalarwinlink1000OduAirCurrentRateIdx | read-only | mandatory | Index of current air rate. |
| 1.3.6.1.4.1.4458.1000.1.5.9.6 | Scalarwinlink1000OduAirChainsRxPower | read-only | mandatory | Received Signal Strength of Cpe chains in dBm. Chain 1 RSS: (1 Byte) Chain 2 RSS: (1 Byte) Chain 3 RSS: (1 Byte) |
| 1.3.6.1.4.1.4458.1000.1.5.9.7 | Scalarwinlink1000OduAirCurrentRateCBW | read-only | mandatory | CBW of current air rate. |
| 1.3.6.1.4.1.4458.1000.1.5.9.8 | Scalarwinlink1000OduAirCurrentRateGI | read-only | mandatory | GI of current air rate. |
| 1.3.6.1.4.1.4458.1000.1.5.10 | Scalarwinlink1000OduAirTxPower36 | read-write | deprecated | Deprecated parameter. Actual behavior is read-only. |
| 1.3.6.1.4.1.4458.1000.1.5.11 | Scalarwinlink1000OduAirTxPower48 | read-write | deprecated | Deprecated parameter. Actual behavior is read-only. |
| 1.3.6.1.4.1.4458.1000.1.5.12 | Scalarwinlink1000OduAirCurrentTxPower | read-only | mandatory | Current Transmit Power in dBm. This is a nominal value while the actual transmit power includes additional attenuation. |
| 1.3.6.1.4.1.4458.1000.1.5.13 | Scalarwinlink1000OduAirMinFrequency | read-only | mandatory | Minimum center frequency in MHz. |
| 1.3.6.1.4.1.4458.1000.1.5.14 | Scalarwinlink1000OduAirMaxFrequency | read-only | mandatory | Maximum center frequency in MHz. |
| 1.3.6.1.4.1.4458.1000.1.5.15 | Scalarwinlink1000OduAirFreqResolution | read-only | mandatory | Center Frequency resolution. Measured in MHz if value < 100, otherwise in KHz. |
| 1.3.6.1.4.1.4458.1000.1.5.16 | Scalarwinlink1000OduAirCurrentFreq | read-only | mandatory | Current Center Frequency. Measured in MHz if center frequency resolution value < 100, otherwise in KHz. |
| 1.3.6.1.4.1.4458.1000.1.5.17 | Scalarwinlink1000OduAirNumberOfChannels | read-only | mandatory | Number of channels that can be used. |
| 1.3.6.1.4.1.4458.1000.1.5.18 | Tablewinlink1000OduAirChannelsTable | not-accessible | mandatory | Table of channels used by automatic channels selection (ACS). |
| 1.3.6.1.4.1.4458.1000.1.5.18.1 | Rowwinlink1000OduAirChannelsEntry | not-accessible | mandatory | ACS channels table entry. |
| 1.3.6.1.4.1.4458.1000.1.5.18.1.1 | Columnwinlink1000OduAirChannelsIndex | read-only | mandatory | Channel Index. |
| 1.3.6.1.4.1.4458.1000.1.5.18.1.2 | Columnwinlink1000OduAirChannelsFrequency | read-only | mandatory | Channel frequency in MHz. |
| 1.3.6.1.4.1.4458.1000.1.5.18.1.3 | Columnwinlink1000OduAirChannelsOperState | read-write | mandatory | Channel state. Can be set by the user. Automatic Channel Selection uses channels that are AirChannelsOperState enabled and AirChannelsAvail enabled. A change i… |
| 1.3.6.1.4.1.4458.1000.1.5.18.1.4 | Columnwinlink1000OduAirChannelsAvail | read-only | mandatory | Channel state. Product specific and cannot be changed by the user. Automatic Channel Selection uses channels that are AirChannelsOperState enabled and AirChann… |
| 1.3.6.1.4.1.4458.1000.1.5.18.1.5 | Columnwinlink1000OduAirChannelsDefaultFreq | read-only | mandatory | Default channel's availability for all CBWs. The valid values are: forbidden (0), available (1). |
| 1.3.6.1.4.1.4458.1000.1.5.19 | Scalarwinlink1000OduAirDfsState | read-only | mandatory | Radar detection state. Valid values: disabled (0), enabled (1). |
| 1.3.6.1.4.1.4458.1000.1.5.20 | Scalarwinlink1000OduAirAutoChannelSelectionState | read-only | deprecated | Deprecated parameter. Indicating Automatic Channel Selection availability at current channel bandwidth. Valid values: disabled (0), enabled (1). |
| 1.3.6.1.4.1.4458.1000.1.5.21 | Scalarwinlink1000OduAirEnableTxPower | read-only | mandatory | Indicating Transmit power configuration enabled or disabled. |
| 1.3.6.1.4.1.4458.1000.1.5.22 | Scalarwinlink1000OduAirMinTxPower | read-only | mandatory | Minimum Transmit power in dBm. |
| 1.3.6.1.4.1.4458.1000.1.5.23 | Tablewinlink1000OduAirMaxTxPowerTable | not-accessible | mandatory | Table of Maximum transmit power per air rate, in dBm. |
| 1.3.6.1.4.1.4458.1000.1.5.23.1 | Rowwinlink1000OduAirMaxTxPowerEntry | not-accessible | mandatory | Maximum Transmit power table entry. |
| 1.3.6.1.4.1.4458.1000.1.5.23.1.1 | Columnwinlink1000OduAirMaxTxPowerIndex | read-only | mandatory | Air interface rate index. |
| 1.3.6.1.4.1.4458.1000.1.5.23.1.2 | Columnwinlink1000OduAirMaxTxPower | read-only | mandatory | Maximum Transmit power in dBm. |
| 1.3.6.1.4.1.4458.1000.1.5.24 | Scalarwinlink1000OduAirChannelBandwidth | read-write | mandatory | Channel bandwidth in KHz. A change is effective after reset. |
| 1.3.6.1.4.1.4458.1000.1.5.25 | Tablewinlink1000OduAirChannelBWTable | not-accessible | mandatory | Channel Bandwidths table. |
| 1.3.6.1.4.1.4458.1000.1.5.25.1 | Rowwinlink1000OduAirChannelBWEntry | not-accessible | mandatory | Channel Bandwidth table entry. |
| 1.3.6.1.4.1.4458.1000.1.5.25.1.1 | Columnwinlink1000OduAirChannelBWIndex | read-only | mandatory | Channel Bandwidth index. |
| 1.3.6.1.4.1.4458.1000.1.5.25.1.2 | Columnwinlink1000OduAirChannelBWAvail | read-only | mandatory | Channel Bandwidth availability, product specific. Options are: Not supported, supported with manual channel selection, supported with Automatic Channel Selecti… |
| 1.3.6.1.4.1.4458.1000.1.5.25.1.3 | Columnwinlink1000OduAirChannelsAdminState | read-only | mandatory | Channels' availability per CBW. |
| 1.3.6.1.4.1.4458.1000.1.5.25.1.4 | Columnwinlink1000OduAirChannelBWHSSATDDConflictPerCBW | read-only | mandatory | Indication for possible Link drop per CBW due to conflict between HSS and ATDD. |
| 1.3.6.1.4.1.4458.1000.1.5.25.1.5 | Columnwinlink1000OduAirChannelBWMinRatioForSupporting | read-only | mandatory | Minimal TX ratio that may be used by the HSM and still enable proper operation of the aforementioned CBW. |
| 1.3.6.1.4.1.4458.1000.1.5.25.1.6 | Columnwinlink1000OduAirChannelBWMaxRatioForSupporting | read-only | mandatory | Maximal TX ratio that may be used by the HSM and still enable proper operation of the aforementioned CBW. |
| 1.3.6.1.4.1.4458.1000.1.5.26 | Scalarwinlink1000OduAirRFD | read-only | mandatory | Current radio frame duration in microseconds. |
| 1.3.6.1.4.1.4458.1000.1.5.27 | Tablewinlink1000OduAirRatesTable | not-accessible | mandatory | Air Rate indexes table for current channel bandwidth. |
| 1.3.6.1.4.1.4458.1000.1.5.27.1 | Rowwinlink1000OduAirRatesEntry | not-accessible | mandatory | Air Rate indexes table entry. |
| 1.3.6.1.4.1.4458.1000.1.5.27.1.1 | Columnwinlink1000OduAirRatesIndex | read-only | mandatory | Air Rate index. |
| 1.3.6.1.4.1.4458.1000.1.5.27.1.2 | Columnwinlink1000OduAirRatesAvail | read-only | mandatory | Air Rate availability, depending on air interface conditions. |
| 1.3.6.1.4.1.4458.1000.1.5.28 | Scalarwinlink1000OduAirDesiredRateIdx | read-write | mandatory | Required Air Rate index. 0 reserved for Adaptive Rate. A change is effective immediately after Set operation to the master side while the link is up. |
| 1.3.6.1.4.1.4458.1000.1.5.29 | Scalarwinlink1000OduAirLinkDistance | read-only | mandatory | Link distance in meters. A value of -1 indicates an illegal value and is also used when a link is not established. |
| 1.3.6.1.4.1.4458.1000.1.5.30 | Scalarwinlink1000OduAirLinkWorkingMode | read-only | mandatory | Link working mode as a result of comparing versions of both sides of the link. Possible modes are: Unknown - no link, Normal - versions on both sides are ident… |
| 1.3.6.1.4.1.4458.1000.1.5.31 | Scalarwinlink1000OduAirMajorLinkIfVersion | read-only | mandatory | Major link interface version |
| 1.3.6.1.4.1.4458.1000.1.5.32 | Scalarwinlink1000OduAirMinorLinkIfVersion | read-only | mandatory | Minor link interface version |
| 1.3.6.1.4.1.4458.1000.1.5.40 | Nodewinlink1000OduAirHss | |||
| 1.3.6.1.4.1.4458.1000.1.5.40.1 | Scalarwinlink1000OduAirHssDesiredOpState | read-write | mandatory | Required Hub Site Synchronization operating state. For HssSyncUnits : For hssISU :[2,7] ,For hssGSU :[2,6] For HBS: [2,3,4,5] |
| 1.3.6.1.4.1.4458.1000.1.5.40.2 | Scalarwinlink1000OduAirHssCurrentOpState | read-only | mandatory | Current Hub Site Synchronization operating state. |
| 1.3.6.1.4.1.4458.1000.1.5.40.3 | Scalarwinlink1000OduAirHssSyncStatus | read-only | mandatory | Hub Site Synchronization sync status. |
| 1.3.6.1.4.1.4458.1000.1.5.40.4 | Scalarwinlink1000OduAirHssExtPulseStatus | read-only | mandatory | Hub Site Synchronization external pulse detection status. In GSS mode: if generating then 1PSP is auto generated by the GSS Unit. if generatingAndDetecting the… |
| 1.3.6.1.4.1.4458.1000.1.5.40.5 | Scalarwinlink1000OduAirHssExtPulseType | read-only | mandatory | Hub Site Synchronization external pulse type. |
| 1.3.6.1.4.1.4458.1000.1.5.40.6 | Scalarwinlink1000OduAirHssDesiredExtPulseType | read-write | mandatory | Hub Site Synchronization required external pulse type. Valid values for read write: {typeA(2),typeB(3),typeC(4),typeD(5),typeE(6),typeF(7)}. Valid value for re… |
| 1.3.6.1.4.1.4458.1000.1.5.40.7 | Tablewinlink1000OduAirHssRfpTable | not-accessible | mandatory | ODU Radio Frame Patterns (RFP) Table. |
| 1.3.6.1.4.1.4458.1000.1.5.40.7.1 | Rowwinlink1000OduAirHssRfpEntry | not-accessible | mandatory | ODU RFP Table entry. |
| 1.3.6.1.4.1.4458.1000.1.5.40.7.1.1 | Columnwinlink1000OduAirHssRfpIndex | read-only | mandatory | ODU RFP Table index. The index represent the Radio Frame Pattern: typeA(2), typeB(3), typeC(4), typeD(5),typeE(6),typeF(7). |
| 1.3.6.1.4.1.4458.1000.1.5.40.7.1.2 | Columnwinlink1000OduAirHssRfpEthChannelBW5MHz | read-only | mandatory | Represents the compatibility of Ethernet service under Channel BW of 5MHz in the specific Radio Frame Pattern. |
| 1.3.6.1.4.1.4458.1000.1.5.40.7.1.3 | Columnwinlink1000OduAirHssRfpTdmChannelBW5MHz | read-only | mandatory | Represents the compatibility of TDM service under Channel BW of 5MHz in the specific Radio Frame Pattern. |
| 1.3.6.1.4.1.4458.1000.1.5.40.7.1.4 | Columnwinlink1000OduAirHssRfpEthChannelBW10MHz | read-only | mandatory | Represents the compatibility of Ethernet service under Channel BW of 10MHz in the specific Radio Frame Pattern. |
| 1.3.6.1.4.1.4458.1000.1.5.40.7.1.5 | Columnwinlink1000OduAirHssRfpTdmChannelBW10MHz | read-only | mandatory | Represents the compatibility of TDM service under Channel BW of 10MHz in the specific Radio Frame Pattern. |
| 1.3.6.1.4.1.4458.1000.1.5.40.7.1.6 | Columnwinlink1000OduAirHssRfpEthChannelBW20MHz | read-only | mandatory | Represents the compatibility of Ethernet service under Channel BW of 20MHz in the specific Radio Frame Pattern. |
| 1.3.6.1.4.1.4458.1000.1.5.40.7.1.7 | Columnwinlink1000OduAirHssRfpTdmChannelBW20MHz | read-only | mandatory | Represents the compatibility of TDM service under Channel BW of 20MHz in the specific Radio Frame Pattern. |
| 1.3.6.1.4.1.4458.1000.1.5.40.7.1.8 | Columnwinlink1000OduAirHssRfpEthChannelBW40MHz | read-only | mandatory | Represents the compatibility of Ethernet service under Channel BW of 40MHz in the specific Radio Frame Pattern. |
| 1.3.6.1.4.1.4458.1000.1.5.40.7.1.9 | Columnwinlink1000OduAirHssRfpTdmChannelBW40MHz | read-only | mandatory | Represents the compatibility of TDM service under Channel BW of 40MHz in the specific Radio Frame Pattern. |
| 1.3.6.1.4.1.4458.1000.1.5.40.7.1.10 | Columnwinlink1000OduAirHssRfpEthChannelBW80MHz | read-only | mandatory | Represents the compatibility of Ethernet service under Channel BW of 80MHz in the specific Radio Frame Pattern. |
| 1.3.6.1.4.1.4458.1000.1.5.40.7.1.11 | Columnwinlink1000OduAirHssRfpEthChannelBW7MHz | read-only | mandatory | Represents the compatibility of Ethernet service under Channel BW of 7MHz in the specific Radio Frame Pattern. |
| 1.3.6.1.4.1.4458.1000.1.5.40.7.1.12 | Columnwinlink1000OduAirHssRfpEthChannelBW14MHz | read-only | mandatory | Represents the compatibility of Ethernet service under Channel BW of 14MHz in the specific Radio Frame Pattern. |
| 1.3.6.1.4.1.4458.1000.1.5.40.8 | Scalarwinlink1000OduAirHssRfpStr | read-only | mandatory | Hub Site Synchronization supported patterns |
| 1.3.6.1.4.1.4458.1000.1.5.40.9 | Scalarwinlink1000OduAirHssHsmID | read-only | mandatory | A unique ID which is common to the HSM and all its collocated ODUs |
| 1.3.6.1.4.1.4458.1000.1.5.40.10 | Scalarwinlink1000OduAirHssTime | read-only | mandatory | Hub Site Synchronization GPS time |
| 1.3.6.1.4.1.4458.1000.1.5.40.11 | Scalarwinlink1000OduAirHssLatitude | read-only | mandatory | Hub Site Synchronization GPS Latitude |
| 1.3.6.1.4.1.4458.1000.1.5.40.12 | Scalarwinlink1000OduAirHssNSIndicator | read-only | mandatory | Hub Site Synchronization GPS N/S Indicator |
| 1.3.6.1.4.1.4458.1000.1.5.40.13 | Scalarwinlink1000OduAirHssLongitude | read-only | mandatory | Hub Site Synchronization GPS Longitude |
| 1.3.6.1.4.1.4458.1000.1.5.40.14 | Scalarwinlink1000OduAirHssEWIndicator | read-only | mandatory | Hub Site Synchronization GPS E/W Indicator |
| 1.3.6.1.4.1.4458.1000.1.5.40.15 | Scalarwinlink1000OduAirHssNumSatellites | read-only | mandatory | Hub Site Synchronization GPS Number of satellites |
| 1.3.6.1.4.1.4458.1000.1.5.40.16 | Scalarwinlink1000OduAirHssAltitude | read-only | mandatory | Hub Site Synchronization GPS Altitude |
| 1.3.6.1.4.1.4458.1000.1.5.40.17 | Scalarwinlink1000OduAirHssRfpPhase | read-write | mandatory | Hub Site Synchronization GPS RFP phase |
| 1.3.6.1.4.1.4458.1000.1.5.40.18 | Scalarwinlink1000OduAirHssInterSiteSynchronizationMode | read-write | mandatory | Inter-Site Synchronization Mode - independent / synchronized |
| 1.3.6.1.4.1.4458.1000.1.5.40.19 | Scalarwinlink1000OduAirHssInterSiteSynchronizationAvailability | read-only | mandatory | Inter-Site Synchronization Availability |
| 1.3.6.1.4.1.4458.1000.1.5.40.20 | Scalarwinlink1000OduAirHssSatellitesSatSyncRequired | read-write | mandatory | Satellites Synchronization Is Required |
| 1.3.6.1.4.1.4458.1000.1.5.40.21 | Scalarwinlink1000OduAirHssDomainID | read-write | mandatory | EHSS domain. Indentify set of CUs with same HSS synchronization |
| 1.3.6.1.4.1.4458.1000.1.5.40.22 | Scalarwinlink1000OduAirHssSupportedSynchronizationProtocol | read-only | mandatory | Supported Synchronization Protocols |
| 1.3.6.1.4.1.4458.1000.1.5.40.23 | Scalarwinlink1000OduAirHssDesiredSynchronizationProtocol | read-write | mandatory | Desired Synchronization Protocols |
| 1.3.6.1.4.1.4458.1000.1.5.40.24 | Scalarwinlink1000OduAirHssDiscover | read-write | mandatory | Initiate Discovery process of ODUs on the network. |
| 1.3.6.1.4.1.4458.1000.1.5.40.25 | Scalarwinlink1000OduAirHssNumberOfDiscoveredODUs | read-only | mandatory | Number OF Discovered ODUs in network. |
| 1.3.6.1.4.1.4458.1000.1.5.40.26 | Tablewinlink1000OduAirHssDiscoverTable | not-accessible | mandatory | HSS Discover Table. |
| 1.3.6.1.4.1.4458.1000.1.5.40.26.1 | Rowwinlink1000OduAirHssDiscoverEntry | not-accessible | mandatory | ODU Discover Table entry. |
| 1.3.6.1.4.1.4458.1000.1.5.40.26.1.1 | Columnwinlink1000OduAirHssDiscoverIndex | read-only | mandatory | HSS Discover Table Index. |
| 1.3.6.1.4.1.4458.1000.1.5.40.26.1.2 | Columnwinlink1000OduAirHssDiscoverODUDescription | read-only | mandatory | Hold ODU HSS status in compress format: Domain,IP,HSS Role,Hss support, Enabled HSS protocol,Sync Status, Location, IPv6. |
| 1.3.6.1.4.1.4458.1000.1.5.40.27 | Scalarwinlink1000OduAirHssMasterSlaveCompatibility | read-only | mandatory | EHSM version compatibility. Relevant to Ethernet HSS Clients only. |
| 1.3.6.1.4.1.4458.1000.1.5.40.28 | Scalarwinlink1000OduAirHssNumberOfAssociatedCU | read-only | mandatory | Number of associated Ethernet HSS Clients. Relevant to Ethernet HSS Masters only |
| 1.3.6.1.4.1.4458.1000.1.5.40.29 | Tablewinlink1000OduAirHssAssociatedCUTable | not-accessible | mandatory | Associated Ethernet HSS Clients Table. Releant for Ethernet HSS Masters only. |
| 1.3.6.1.4.1.4458.1000.1.5.40.29.1 | Rowwinlink1000OduAirHssAssociatedCUTableEntry | not-accessible | mandatory | Associated Ethernet HSS Clients Table Entry. Releant for Ethernet HSS Masters only. |
| 1.3.6.1.4.1.4458.1000.1.5.40.29.1.1 | Columnwinlink1000OduAirHssAssociatedCUIndex | read-only | mandatory | Associated Ethernet HSS Clients Table Index. Releant for Ethernet HSS Masters only. |
| 1.3.6.1.4.1.4458.1000.1.5.40.29.1.2 | Columnwinlink1000OduAirHssAssociatedCUDescription | read-only | mandatory | Holds Associated Ethernet HSS Clients Description in compress format: IP,Delay,Compatibility,Ethernet Speed, Ethernet Rx rate, IPv6 |
| 1.3.6.1.4.1.4458.1000.1.5.40.30 | Scalarwinlink1000OduAirHssSyncStatusEth | read-only | mandatory | Ethernet HSS Client Synchronization Level |
| 1.3.6.1.4.1.4458.1000.1.5.40.31 | Scalarwinlink1000OduAirHssEthVLANTag | read-write | mandatory | Ethernet HSS VLan Tag: The least significate decimal digit is the VLan Priority(0-6) and the rest of the digits represents VLan ID (2-4094) |
| 1.3.6.1.4.1.4458.1000.1.5.40.32 | Scalarwinlink1000OduAirHssHSMIPAddress | read-only | mandatory | HSMs IP address. Relevant for HSC synchronized over Ethernet. |
| 1.3.6.1.4.1.4458.1000.1.5.40.33 | Scalarwinlink1000OduAirHssDelayToHSM | read-only | mandatory | Delay in microseconds to HSM. Relevant for HSC synchronized over Ethernet. |
| 1.3.6.1.4.1.4458.1000.1.5.40.34 | Scalarwinlink1000OduAirHssSyncAcquisitionSeconds | read-write | mandatory | Accumulated quantity of seconds in clock acquisition while connected to current HSM |
| 1.3.6.1.4.1.4458.1000.1.5.40.35 | Scalarwinlink1000OduAirHssHSMIPv6Address | read-only | mandatory | HSMs IPv6 address. Relevant for HSC synchronized over Ethernet. |
| 1.3.6.1.4.1.4458.1000.1.5.41 | Scalarwinlink1000OduAirLockRemote | read-write | mandatory | This parameter enables locking the link with a specific ODU. The following values can be set: Unlock (default) - The ODU is not locked on a specific remote ODU… |
| 1.3.6.1.4.1.4458.1000.1.5.42 | Scalarwinlink1000OduAirAntennaGain | read-write | mandatory | Current Antenna Gain in 0.1 dBi resolution. User defined value for external antenna. Legal range: MinAntennaGain - Alarm. |
| 1.3.6.1.4.1.4458.1000.105 | NodeexternalAlarmInPort1Alarm | The trap is sent every time an alarm occurs in the External Alarm Input of port #1. Contains a single parameter, which is its description: 1 - Description: Ext… | ||
| 1.3.6.1.4.1.4458.1000.106 | NodeexternalAlarmInPort2Alarm | The trap is sent every time an alarm occurs in the External Alarm Input of port #2. Contains a single parameter, which is its description: 1 - Description: Ext… | ||
| 1.3.6.1.4.1.4458.1000.107 | NodebitFailedAlarm | The trap is sent if there is no way to recover from the situation. Contains two parameters: 1 - Description: ODU power up built in test failed. Error code is: … | ||
| 1.3.6.1.4.1.4458.1000.108 | NodewrongConfigurationLoadedAlarm | The trap is sent if there is a way to recover from the situation. Contains two parameters: 1 - Description: Wrong configuration loaded. Error code is: %n 2 - %… | ||
| 1.3.6.1.4.1.4458.1000.109 | NodelanPort1DisconnectedAlarm | Indicates the LAN port 1 status changed to disconnected. Contains a single parameter, which is its description: 1 - Description: LAN port 1 status changed to d… | ||
| 1.3.6.1.4.1.4458.1000.110 | NodelanPort2DisconnectedAlarm | Indicates the LAN port 2 status changed to disconnected. Contains a single parameter, which is its description: 1 - Description: LAN port 2 status changed to d… | ||
| 1.3.6.1.4.1.4458.1000.111 | NodemngPortDisconnectedAlarm | Indicates the LAN1 port status changed to disconnected. Contains a single parameter, which is its description: 1 - Description: LAN1 port status changed to dis… | ||
| 1.3.6.1.4.1.4458.1000.112 | NodeexternalAlarmInPort3Alarm | The trap is sent every time an alarm occurs in the External Alarm Input of port #3. Contains a single parameter, which is its description: 1 - Description: Ext… | ||
| 1.3.6.1.4.1.4458.1000.113 | NodeexternalAlarmInPort4Alarm | The trap is sent every time an alarm occurs in the External Alarm Input of port #4. Contains a single parameter, which is its description: 1 - Description: Ext… | ||
| 1.3.6.1.4.1.4458.1000.114 | NodeswVersionsMismatchFullCompatibilityAlarm | The trap is sent if SW versions mismatch with full link functionality. Contains a single parameter, which is its description: 1 - Description: Software version… | ||
| 1.3.6.1.4.1.4458.1000.115 | NodeswVersionsMismatchRestrictedCompatibilityAlarm | The trap is sent if SW versions mismatch with restricted link functionality. Contains a single parameter, which is its description: 1 - Description: Software v… | ||
| 1.3.6.1.4.1.4458.1000.116 | NodeswVersionsMismatchSoftwareUpgradeRequired | The trap is sent if SW versions mismatch and SW upgrade is required. Contains a single parameter, which is its description: 1 - Description: Software versions … | ||
| 1.3.6.1.4.1.4458.1000.117 | NodeswVersionsIncompatible | The trap is sent if SW versions are incompatible. Contains a single parameter, which is its description: 1 - Description: SW Versions incompatible | ||
| 1.3.6.1.4.1.4458.1000.118 | NodehssMultipleSourcesDetectedAlarm | Indicates that multiple sync pulse sources were detected. Contains a single parameter, which is its description: 1 - Description: HSS multiple sync sources wer… | ||
| 1.3.6.1.4.1.4458.1000.119 | NodehssSyncToProperSourceStoppedAlarm | Indicates that synchronization to a proper sync pulse source was stopped. Contains a single parameter, which is its description: 1 - Description: HSS sync puls… | ||
| 1.3.6.1.4.1.4458.1000.120 | NodehssSyncPulseDetectedAlarm | Indicates that HSS additional sync pulse was detected. Contains a single parameter, which is its description: 1 - Description: HSS additional sync pulse was de… | ||
| 1.3.6.1.4.1.4458.1000.121 | NodetdmBackupAlarm | Indicates that the TDM backup link was activated. Contains a single parameter, which is its description: 1 - Description: TDM backup alarm - backup link was ac… | ||
| 1.3.6.1.4.1.4458.1000.122 | NodelinkLockUnauthorizedRemoteODU | Indicates that the remote ODU is unauthorized. Contains a single parameter, which is its description: 1 - Description: Unauthorized remote ODU connection rejec… | ||
| 1.3.6.1.4.1.4458.1000.123 | NodelinkLockUnauthorizedODU | Indicates that the ODU is unauthorized. Contains a single parameter, which is its description: 1 - Description: Unauthorized ODU connection rejected. | ||
| 1.3.6.1.4.1.4458.1000.124 | NodehotStandbyAlarm | Indicates that the hot standby secondary link was activated. Contains a single parameter, which is its description: 1 - Description: Secondary Link Is Active. | ||
| 1.3.6.1.4.1.4458.1000.126 | NodesfpInsertion | Indicates that a device was inserted to SFP Port | ||
| 1.3.6.1.4.1.4458.1000.127 | NodesfpPort1DisconnectedAlarm | Indicates the SFP port 1 status changed to disconnected. Contains a single parameter which is its description: 1 - Description: SFP port 1 status changed to di… | ||
| 1.3.6.1.4.1.4458.1000.128 | NoderingRplStateActiveAlarm | RPL state changed to Active. | ||
| 1.3.6.1.4.1.4458.1000.129 | NodedesiredRatioCanNotBeAppliedAlarm | Indicates Desired UL/DL RAtio Can Not Be Applied. | ||
| 1.3.6.1.4.1.4458.1000.130 | NodecbwMismatch | Indicates that a Channel Bandwidth mismatch was detected. Contains two parameters: 1 - Description: Channel Bandwidth Mismatch: one side is %n0 MHz and the oth… | ||
| 1.3.6.1.4.1.4458.1000.131 | NodegpsNotSynchronized | Indicates that the GPS is not synchronized with satellites. Pulses are self generated. | ||
| 1.3.6.1.4.1.4458.1000.132 | NodepdTooHighDueCbwLimitations | Indicates that link cannot be established because link range is too large for channel bandwidth. | ||
| 1.3.6.1.4.1.4458.1000.133 | NodehbsEncryptionAlarm | Indicates an encryption key mismatch. Contains a single parameter, which is its description, including the HSU's name | ||
| 1.3.6.1.4.1.4458.1000.134 | NodehbsEhServiceClosedToHsu | Indicates an encryption key mismatch. Contains a single parameter, which is its description, including the HSU's name | ||
| 1.3.6.1.4.1.4458.1000.135 | NodehbsUnsynchronizedHsuAlarm | Indicates a registered HSU lost synchronization. | ||
| 1.3.6.1.4.1.4458.1000.136 | NodehbsInactiveHbsAlarm | Indicates HBS is InActive. | ||
| 1.3.6.1.4.1.4458.1000.137 | NodeincompatibleHsu | Indicates that the HSU is not compatible to HBS. Contains a single parameter, which is its description: 1 - Description: Incompatible ODUs. | ||
| 1.3.6.1.4.1.4458.1000.138 | NodehsuUnsupportedBeacon | Indicates an unsupported beacon has arrived at HSU | ||
| 1.3.6.1.4.1.4458.1000.139 | NodelanPortDisconnectedAlarm | Indicates the LAN port status changed to disconnected. Contains a single parameter, which is its description: 1 - Description: LAN port status changed to disco… | ||
| 1.3.6.1.4.1.4458.1000.140 | NodepoePortDisconnectedAlarm | Indicates the LAN2 port status changed to disconnected. Contains a single parameter, which is its description: 1 - Description: LAN2 port status changed to dis… | ||
| 1.3.6.1.4.1.4458.1000.141 | NodepoePowerConsumptionAlarm | Indicates the POE Power Consumption is above allowed maximum. Contains a single parameter, which is its description: 1 - Description: POE consumption above all… | ||
| 1.3.6.1.4.1.4458.1000.149 | NodehobupFaultyStateAlarm | This Alarm will indicate that the Hot Backup module is in faulty state. 1 - Description: Hot Backup fault detected: %s unit. %s - Primary Or Secondary Unit | ||
| 1.3.6.1.4.1.4458.1000.150 | NodegpsOverCurrentAlarm | Indicates the GPS Antenna current consumption is above allowed maximum. Contains a single parameter, which is its description: 1 - Description: GPS Antenna cur… | ||
| 1.3.6.1.4.1.4458.1000.151 | NodegpsCommunicationFailiureAlarm | Indicates the GPS data isn't received. Contains a single parameter, which is its description: 1 - Description: GPS Communication failiure. | ||
| 1.3.6.1.4.1.4458.1000.152 | NodetemperatureThresholdAlarm | Indicates the board temperature is above allowed maximum. Contains a single parameter, which is its description: 1 - Description: GPS Antenna current consumpti… | ||
| 1.3.6.1.4.1.4458.1000.153 | NodelocalRouterDiscoveryStatus | This Alarm will indicate that we have no connection with local train router. 1 - Description: MacLearningUpdate detected disconnection with local train router … | ||
| 1.3.6.1.4.1.4458.1000.154 | NodetrackRouterDiscoveryStatus | This Alarm will indicate that we have no connection with Track side router. 1 - Description: MacLearningUpdate detected disconnection with Track side router %s… | ||
| 1.3.6.1.4.1.4458.1000.155 | NodelastUserSnmpAccessOverHourAgo | This trap will indicate that the last access of the accessing user was more than an hour ago. 1 - Description: User %s performed SNMP access after more than an… | ||
| 1.3.6.1.4.1.4458.1000.156 | NodebtsTargetUnreachable | This Alarm will indicate that we have no connection with Bts desired target. 1 - Description: TNC detected disconnection with the BTS target %s %s - Default ga… | ||
| 1.3.6.1.4.1.4458.1000.200 | NodetdmServiceClear | Indicates that TDM Service fault is cleared. Contains a single parameter, which is its description: 1 - Description: TDM Service - Normal. | ||
| 1.3.6.1.4.1.4458.1000.201 | NodeethServiceOpened | Indicates that Ethernet Service has been opened. Contains a single parameter, which is its description: 1 - Description: Ethernet Service has been opened. | ||
| 1.3.6.1.4.1.4458.1000.203 | NodeencryptionClear | Indicates that encryption is OK. Contains a single parameter, which is its description: 1 - Description: Encryption Status - Normal. | ||
| 1.3.6.1.4.1.4458.1000.204 | NodechangeLinkPasswordClear | Indicates that the Link Password was changed successfully. Contains a single parameter, which is its description: 1 - Description: Link Password has been chang… | ||
| 1.3.6.1.4.1.4458.1000.205 | NodeexternalAlarmInPort1Clear | This Trap is sent every time an External Alarm Input fault of port # 1 is cleared. Contains a single parameter, which is its description: 1 - Description: Exte… | ||
| 1.3.6.1.4.1.4458.1000.206 | NodeexternalAlarmInPort2Clear | This Trap is sent every time an External Alarm Input fault of port # 2 is cleared. Contains a single parameter, which is its description: 1 - Description: Exte… | ||
| 1.3.6.1.4.1.4458.1000.209 | NodelanPort1Clear | Indicates the LAN port 1 status changed to connected. Contains two parameters: 1 - Description: LAN port 1 status changed to connected - %s 2 - %s Is the Eth. … | ||
| 1.3.6.1.4.1.4458.1000.210 | NodelanPort2Clear | Indicates the LAN port 2 status changed to connected. Contains two parameters: 1 - Description: LAN port 2 status changed to connected - %s. 2 - %s Is the Eth.… | ||
| 1.3.6.1.4.1.4458.1000.211 | NodemngPortClear | Indicates the LAN1 port status changed to connected. Contains two parameters: 1 - Description: LAN1 port status changed to connected - %s 2 - %s Is the Eth. mo… | ||
| 1.3.6.1.4.1.4458.1000.212 | NodeexternalAlarmInPort3Clear | This Trap is sent every time an External Alarm Input fault of port # 3 is cleared. Contains a single parameter, which is its description: 1 - Description: Exte… | ||
| 1.3.6.1.4.1.4458.1000.213 | NodeexternalAlarmInPort4Clear | This Trap is sent every time an External Alarm Input fault of port # 4 is cleared. Contains a single parameter, which is its description: 1 - Description: Exte… | ||
| 1.3.6.1.4.1.4458.1000.214 | NodeswVersionsMatchFullCompatibilityClear | The trap is sent if SW versions match. Contains a single parameter, which is its description: 1 - Description: Software Versions compatible | ||
| 1.3.6.1.4.1.4458.1000.215 | NodeswVersionsMatchRestrictedCompatibilityClear | The trap is sent if SW versions match and link functionality is not restricted. Contains a single parameter, which is its description: 1 - Description: Softwar… | ||
| 1.3.6.1.4.1.4458.1000.216 | NodeswVersionsMatchSoftwareUpgradeRequiredClear | The trap is sent if SW versions match and SW upgrade is successful. Contains a single parameter, which is its description: 1 - Description: Software Versions c… | ||
| 1.3.6.1.4.1.4458.1000.217 | NodeswVersionsCompatibleClear | The trap is sent if SW versions compatible Contains a single parameter, which is its description: 1 - Description: Software Versions compatible | ||
| 1.3.6.1.4.1.4458.1000.218 | NodehssMultipleSourcesDisappearedClear | Indicates that multiple sync pulse sources disappeared. Contains a single parameter, which is its description: 1 - Description: HSS multiple sync pulse sources… | ||
| 1.3.6.1.4.1.4458.1000.219 | NodehssSyncToProperSourceAchievedClear | Indicates that synchronization to a proper Sync source was achieved. Contains a single parameter, which is its description: 1 - Description: HSS sync pulse - U… | ||
| 1.3.6.1.4.1.4458.1000.220 | NodehssSyncPulseDisappearedClear | Indicates that HSS additional sync pulse disappeared. Contains a single parameter, which is its description: 1 - Description: HSS additional sync pulse was dis… | ||
| 1.3.6.1.4.1.4458.1000.221 | NodetdmBackupClear | Indicates that the TDM main link was activated. Contains a single parameter, which is its description: 1 - Description: TDM main link was activated. | ||
| 1.3.6.1.4.1.4458.1000.222 | NodelinkLockAuthorizedRemoteODU | Indicates that the remote ODU is authorized. Contains a single parameter, which is its description: 1 - Description: Authorized remote ODU connection accepted. | ||
| 1.3.6.1.4.1.4458.1000.223 | NodelinkLockAuthorizedODU | Indicates that the ODU is authorized. Contains a single parameter, which is its description: 1 - Description: Authorized ODU connection permitted. | ||
| 1.3.6.1.4.1.4458.1000.224 | NodelinkAuthenticationDisabled | Indicates that the Link Lock is disabled. Contains a single parameter, which is its description: 1 - Description: Link Authentication has been disabled. | ||
| 1.3.6.1.4.1.4458.1000.225 | NodehotStandbyClear | Indicates that the Primary Link Was Activated. Contains a single parameter, which is its description: 1 - Description: Primary Link Is Active. | ||
| 1.3.6.1.4.1.4458.1000.226 | NodesfpExtraction | Indicates that a device was extracted from SFP Port | ||
| 1.3.6.1.4.1.4458.1000.227 | NodesfpPort1Clear | Indicates the SFP port 1 status changed to connected. Contains two parameters: 1 - Description: SFP port 1 status changed to connected - %s 2 - %s Is the Eth. … | ||
| 1.3.6.1.4.1.4458.1000.228 | NodecompatibleIdus | Indicates that the ODU has identified compatible Idus on both sides of the link. | ||
| 1.3.6.1.4.1.4458.1000.229 | NodedesiredRatioCanNotBeAppliedClear | Indicates Current UL/DL Ratio Is Equal To Desired Ratio. | ||
| 1.3.6.1.4.1.4458.1000.230 | NodecbwMatch | Indicates that a Channel Bandwidth match was detected. Contains a single parameter, which is its description: 1 - Channel Bandwidth value in MHz. | ||
| 1.3.6.1.4.1.4458.1000.231 | NodeswitchCbwAndChannel | Indicates that the system is switching Channel Bandwidth and channel frequency. Contains two parameters: 1 - Switching to Channel Bandwith %n0 MHz and to chann… | ||
| 1.3.6.1.4.1.4458.1000.232 | NoderingRplStateIdle | RPL state changed to Idle. | ||
| 1.3.6.1.4.1.4458.1000.233 | NoderingEthServiceStatus | Indicates Ethernet service's state - blocked \ unblocked. Contains a single parameter: 1 - Description: Ethernet's state (blocked \ unblocked) | ||
| 1.3.6.1.4.1.4458.1000.234 | NoderingFirstRpmReceived | Ring application: in non-RPL link indicates first from a specific RPL was received. Contains a single parameter: 1 - Description: RPM's VLAN ID | ||
| 1.3.6.1.4.1.4458.1000.235 | NoderingEthernetSrviceUnblockedTO | Ring application: in non-RPL link Ethernet service is unblocked due to RPM timeout. | ||
| 1.3.6.1.4.1.4458.1000.236 | NodegpsSynchronized | Indicates that the GPS is synchronized with satellites. | ||
| 1.3.6.1.4.1.4458.1000.237 | NodehbsEncryptionClear | Indicates that encryption is OK. Contains a single parameter, which is its description, including the HSU's name | ||
| 1.3.6.1.4.1.4458.1000.238 | NodehbsEhServiceOpenedToHsu | Indicates that encryption is OK. Contains a single parameter, which is its description, including the HSU's name | ||
| 1.3.6.1.4.1.4458.1000.239 | NodehbsSynchronizedHsuAlarm | Indicates a registered HSU is synchronized. | ||
| 1.3.6.1.4.1.4458.1000.240 | NodehbsActiveHbs | Indicates when HBS has been activated. | ||
| 1.3.6.1.4.1.4458.1000.241 | NodeswitchCBW | Switching Channel Bandwidth. | ||
| 1.3.6.1.4.1.4458.1000.242 | NodechangeRatio | HBS Tx ratio has changed. | ||
| 1.3.6.1.4.1.4458.1000.243 | NodelanPortClear | Indicates the LAN port status changed to connected. Contains two parameters: 1 - Description: LAN port status changed to connected - %s 2 - %s Is the Eth. mode… | ||
| 1.3.6.1.4.1.4458.1000.244 | NodepoePortClear | Indicates the LAN2 port status changed to connected. Contains two parameters: 1 - Description: LAN2 port status changed to connected - %s 2 - %s Is the Eth. mo… | ||
| 1.3.6.1.4.1.4458.1000.245 | NodepoePowerConsumptionClear | Indicates the POE power consumption is valid. Contains two parameters: 1 - Description: POE consumption within limits. port is opened. 2 - %s Is the Eth. mode … | ||
| 1.3.6.1.4.1.4458.1000.246 | NodeincompatibleHbsHsu | Incompatible HBS/HSU software versions - no service. | ||
| 1.3.6.1.4.1.4458.1000.247 | NodemobilityLinkOff | Mobility - Link cannot be established due to: 1 - The HBS does not support Mobility 2 - Lack of resources in the HBS for HSU level | ||
| 1.3.6.1.4.1.4458.1000.248 | NodeenterLocalConnection | Entering Local Connection (Broadcast) Mode. | ||
| 1.3.6.1.4.1.4458.1000.249 | NodehobupActiveStateFaultyClear | this clear alarm will indicate that the Hot Backup unit is in active state. Contains a single parameter, which is its description: 1 - Description: Hot Backup … | ||
| 1.3.6.1.4.1.4458.1000.250 | NodehobupStandbyState | This info fault will indicate that the Hot backup module has entered standby/peer_detection state Contains a single parameter, which is its description: 1 - De… | ||
| 1.3.6.1.4.1.4458.1000.251 | NodegpsOverCurrentClear | Indicates the GPS Antenna current consumption is valid. | ||
| 1.3.6.1.4.1.4458.1000.252 | NodetemperatureThresholdClear | Indicates the board temperature is valid. | ||
| 1.3.6.1.4.1.4458.1000.253 | NodelocalRouterDiscoverySucceed | Indicated the we succeeded to discover train router in ip %s MAC address %s %s Train IP %s Train MAC Address | ||
| 1.3.6.1.4.1.4458.1000.254 | NodetrackRouterDiscoverySucceed | Indicated the we succeeded to discover track router in ip %s MAC address %s %s Train IP %s Train MAC Address | ||
| 1.3.6.1.4.1.4458.1000.255 | NodeqosVersion2StrictMismatch | CPE doesn't support strict QOS configuration. | ||
| 1.3.6.1.4.1.4458.1000.256 | NodeqosVersion2TtlMismatch | CPE doesn't support TTL configuration. | ||
| 1.3.6.1.4.1.4458.1000.257 | NodebtsTargetIsReachable | Indicated the we succeeded to establish connection with the Bts desired target (%s) %s Target IP | ||
| 1.3.6.1.4.1.4458.1000.258 | NodetcNotSupportedByHSU | CPE doesn't support TC functionality. | ||
| 1.3.6.1.4.1.4458.1000.259 | NodesyncEPortHOStateChange | Enter/leave HO state of SyncE port. | ||
| 1.3.6.1.4.1.4458.1000.260 | NodesyncEPortFailureStateChange | Enter/leave Failure state of SyncE port. | ||
| 1.3.6.1.4.1.4458.1000.261 | NodebtsCpeUpdateServiceFailed | Update service Failed | ||
| 1.3.6.1.4.1.4458.1000.262 | NodebtsCpeUpdateServiceSucceed | Update service Succeed | ||
| 1.3.6.1.4.1.4458.1000.263 | NoderadiusServerNoREsponse | No response from radius server | ||
| 1.3.6.1.4.1.4458.1000.264 | NodenoRadiusServerRespond | Alarm indicates that no Radius server is connected | ||
| 1.3.6.1.4.1.4458.1000.265 | NoderadiusServerRespondedSuccessfully | indicates that Radius server responded seccessfully. | ||
| 1.3.6.1.4.1.4458.1000.266 | NodebsaAlignmentStarted | Indicate the beginning of Alignment Process | ||
| 1.3.6.1.4.1.4458.1000.267 | NodebsaAlignmentFinished | Indicate the completion of Alignment Process | ||
| 1.3.6.1.4.1.4458.1000.268 | NodebsaAlignmentTriggered | Indicate the triggering of Alignment Process due to exceeding thresholds |