MIB Viewer

RAINBOW-MIB

503 objects
Rainbow MIB
Imported Objects
ALVARION-TOP-MIBproducts
SNMPv2-SMIInteger32 IpAddress MODULE-IDENTITY OBJECT-TYPE TimeTicks Unsigned32
SNMPv2-TCDisplayString MacAddress RowStatus TEXTUAL-CONVENTION
OIDNameAccessStatusDescription
1.3.6.1.4.1.12394.1.2IdentityrainbowRainbow MIB
1.3.6.1.4.1.12394.1.2.1NoderbSysConfig
1.3.6.1.4.1.12394.1.2.1.1NoderbSysGeneral
1.3.6.1.4.1.12394.1.2.1.1.1ScalarrbSysFaultStatusread-onlycurrentThe summarized severity of the entire System fault status. Not supported in current version.
1.3.6.1.4.1.12394.1.2.1.1.2ScalarrbSysLastTrapSeqNumberread-onlycurrentThe last trap sequence number before the reset.
1.3.6.1.4.1.12394.1.2.2NoderbChassisConfig
1.3.6.1.4.1.12394.1.2.2.1TablerbSlotConfigTablenot-accessiblecurrentThis table provides parameters common for all cards in chassis slots. It is retrieved with community NPU
1.3.6.1.4.1.12394.1.2.2.1.1RowrbSlotConfigEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.2.1.1.1ColumnrbSlotNumberread-onlycurrentPhysical placement of the card in the chassis (the Slot number). This is the table index {1 up to 9}.
1.3.6.1.4.1.12394.1.2.2.1.1.2ColumnrbSlotDetectedCardread-onlycurrentThe auto detected card type. It also indicates whether the slot has a card inserted in it or not.
1.3.6.1.4.1.12394.1.2.2.1.1.3ColumnrbSlotConfiguredCardread-writecurrentThe card type that is configured for the slot. In current version this is read_only (AU is configured for slots 1-4 and 7-9, Slot 5 is NPU, slot 6 is Not Insta…
1.3.6.1.4.1.12394.1.2.2.1.1.4ColumnrbSlotAllowedCardread-onlycurrentThe card type that is allowed to be inserted in the specific slot. In slots 1-4, 7-9 the allowed card is AU. In slots 5 and the allowed card is NPU, although i…
1.3.6.1.4.1.12394.1.2.2.1.1.5ColumnrbSlotLedStatusread-onlycurrentNot supported in current version. This field represents summarized information about the card leds. Each byte represents the single Led. Within each byte, bits…
1.3.6.1.4.1.12394.1.2.2.1.1.6ColumnrbSlotFaultStatusread-onlycurrentThe severity of the card fault. This is summarized information regarding the card healthiness in the slot. In case that there is no connection between NPU and …
1.3.6.1.4.1.12394.1.2.2.1.1.7ColumnrbSlotExtractorStateread-onlycurrentThe current state of the card extractor - closed or opened. In the current version this parameter is not supported and the status is always unknown.
1.3.6.1.4.1.12394.1.2.2.2NoderbNpuConfiguration
1.3.6.1.4.1.12394.1.2.2.2.1TablerbNpuConfigTablenot-accessiblecurrentThis table provides NPU configuration parameters.
1.3.6.1.4.1.12394.1.2.2.2.1.1RowrbNpuConfigEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.2.2.1.1.1ColumnrbNpuSerialNoread-onlycurrentSerial number assigned for the card during the production time.
1.3.6.1.4.1.12394.1.2.2.2.1.1.2ColumnrbNpuSysNameread-writecurrentThe name of the card; like System Name in MIB-II.
1.3.6.1.4.1.12394.1.2.2.2.1.1.3ColumnrbNpuFaultStatusread-onlycurrentThe severity of the card fault. This is summarized information regarding the card healthiness in the slot.
1.3.6.1.4.1.12394.1.2.2.2.1.1.4ColumnrbNpuHwRevisionread-onlycurrentHardware revision of the card.
1.3.6.1.4.1.12394.1.2.2.2.1.1.5ColumnrbNpuOperSwFileNameread-onlycurrentOperational (Main) Software File Name.
1.3.6.1.4.1.12394.1.2.2.2.1.1.6ColumnrbNpuOperSwVersionread-onlycurrentOperational (Main) Software Version.
1.3.6.1.4.1.12394.1.2.2.2.1.1.7ColumnrbNpuShadowSwFileNameread-onlycurrentShadow Software File Name.
1.3.6.1.4.1.12394.1.2.2.2.1.1.8ColumnrbNpuShadowSwVersionread-onlycurrentShadow Software Version.
1.3.6.1.4.1.12394.1.2.2.2.1.1.9ColumnrbNpuRunningSoftwareread-onlycurrentCurrent running software.
1.3.6.1.4.1.12394.1.2.2.2.1.1.10ColumnrbNpuOperVersionValidityread-onlycurrentThe validity of the Operational (Main) Software. Not supported in current version.
1.3.6.1.4.1.12394.1.2.2.2.1.1.11ColumnrbNpuShadowVersionValidityread-onlycurrentThe validity of the Shadow Software. Not supported in current version.
1.3.6.1.4.1.12394.1.2.2.2.1.1.12ColumnrbNpuRedundancyStatusread-writecurrentNPU redundancy status. This parameters is read only (always active) in current version.
1.3.6.1.4.1.12394.1.2.2.2.1.1.13ColumnrbNpuUnitControlread-writecurrentIf resetAndRunFromShadow (4) is selected, card should perform reset and boot from the shadow software image. If makeRunningVersionOperational (5) is selected a…
1.3.6.1.4.1.12394.1.2.2.2.1.1.14ColumnrbNpuSetDefaultsread-writecurrentThis parameter defines the way 'Default Group' parameters are initialised with default values: 1 - Default values should not be copied to the Flash Memory, 2 -…
1.3.6.1.4.1.12394.1.2.2.2.1.1.15ColumnrbNpuHwConfigDescriptionread-onlycurrentNPU Hardware configuration description.
1.3.6.1.4.1.12394.1.2.2.2.1.1.16ColumnrbNpuManagementInterfaceread-writecurrentThe index of the NPU interface that can be used for management. This parameters is read only in current version, and it is always 2 (both ports can be used for…
1.3.6.1.4.1.12394.1.2.2.2.1.1.17ColumnrbNpuCreateConfigFileread-writecurrentNot applicable for Version 2 and higher. This variable is used to instruct the NPU to create file containing the Base Station configuration. Variable contains …
1.3.6.1.4.1.12394.1.2.2.2.1.1.18ColumnrbNpuCreateBackupConfigFileread-writecurrentThis variable is used to instruct the NPU to create file containing the Base Station configuration. cfgFileFull (1) is used for creating full backup files, nam…
1.3.6.1.4.1.12394.1.2.2.2.1.1.19ColumnrbNpuCumulativePowerOnTimeread-onlycurrentCumulative Power On Time (minutes). Agent will return 0 if Cumulative Power On Time is unknown.
1.3.6.1.4.1.12394.1.2.2.2.1.1.20ColumnrbNpuBootSwVersionread-onlycurrentBoot Software Version.
1.3.6.1.4.1.12394.1.2.2.2.1.1.21ColumnrbNpuTemperatureread-onlycurrentNPU Messured Temperature.
1.3.6.1.4.1.12394.1.2.2.2.1.1.22ColumnrbNpuDrapTtlRetriesread-writecurrentNPU DRAP TTL Retries. Sets the limit of TTL retries for gateways that support the DRAP protocol before concluding that the gateway is no longer active and remo…
1.3.6.1.4.1.12394.1.2.2.2.1.1.23ColumnrbNpuRedundantCPLDVersionread-onlycurrentNPU Redundant CPLD Version. The Redundant CPLD is needed to enable GPS support.
1.3.6.1.4.1.12394.1.2.2.2.2NoderbNpuBridgingParameters
1.3.6.1.4.1.12394.1.2.2.2.2.1ScalarrbNpuBridgeAgingTimeread-writecurrentThe Aging Time for the NPU Bridging tables in minutes. 0 is for No Aging.
1.3.6.1.4.1.12394.1.2.2.2.3NoderbNpuFrequencyBandsParameters
1.3.6.1.4.1.12394.1.2.2.2.3.1ScalarrbFrequencyBandsFileVersionread-onlycurrentThe version of the Frequency Bands File.
1.3.6.1.4.1.12394.1.2.2.2.3.2TablerbFrequencyBandsTablenot-accessiblecurrentA table that holds the main details of the bands in the current Frequency Bands File.
1.3.6.1.4.1.12394.1.2.2.2.3.2.1RowrbFrequencyBandsEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.2.2.3.2.1.1ColumnrbFrequencyBandIdread-onlycurrentThe ID of the Frequency Band.
1.3.6.1.4.1.12394.1.2.2.2.3.2.1.2ColumnrbFrequencyBandNameread-onlycurrentThe name of the Frequency Band.
1.3.6.1.4.1.12394.1.2.2.2.3.2.1.3ColumnrbFrequencyBandRevisionread-onlycurrentThe revision of the Frequency Band.
1.3.6.1.4.1.12394.1.2.2.2.3.2.1.4ColumnrbFrequencyBandGroupIdread-onlycurrentThe Group ID of the Frequency Band.
1.3.6.1.4.1.12394.1.2.2.2.3.2.1.5ColumnrbFrequencyBandStartFrequencyread-onlycurrentDownlink Start Frequency [MHz].
1.3.6.1.4.1.12394.1.2.2.2.3.2.1.6ColumnrbFrequencyBandStopFrequencyread-onlycurrentDownlink Stop Frequency [MHz].
1.3.6.1.4.1.12394.1.2.2.2.3.2.1.7ColumnrbFrequencyBandStepread-onlycurrentThe Frequency resolution [MHz].
1.3.6.1.4.1.12394.1.2.2.2.3.2.1.8ColumnrbFrequencyBandDuplexSeparationread-onlycurrentDuplex Frequency Separation [MHz].
1.3.6.1.4.1.12394.1.2.2.3TablerbAuConfigTablenot-accessiblecurrentThis table provides Access Unit configuration parameters.
1.3.6.1.4.1.12394.1.2.2.3.1RowrbAuConfigEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.2.3.1.1ColumnrbAuSerialNoread-onlycurrentSerial number assigned for the card during the production time.
1.3.6.1.4.1.12394.1.2.2.3.1.2ColumnrbAuSysNameread-writecurrentLogical card ID, providing unique identification of the card. Note that SysName for AU is not supported by MIB II (as well as SysLocation and SysContact).
1.3.6.1.4.1.12394.1.2.2.3.1.3ColumnrbAuFaultStatusread-onlycurrentThe severity of the card fault. This is summarized information regarding the card healthiness in the slot.
1.3.6.1.4.1.12394.1.2.2.3.1.4ColumnrbAuIduTemperatureread-onlycurrentAU-IDU Temperature (Celsius).
1.3.6.1.4.1.12394.1.2.2.3.1.5ColumnrbAuIduHwRevisionread-onlycurrentHardware revision of the AU-IDU card.
1.3.6.1.4.1.12394.1.2.2.3.1.6ColumnrbAuOperSwFileNameread-onlycurrentOperational (Main) Software File Name.
1.3.6.1.4.1.12394.1.2.2.3.1.7ColumnrbAuOperSwVersionread-onlycurrentOperational (Main) Software Version.
1.3.6.1.4.1.12394.1.2.2.3.1.8ColumnrbAuShadowSwFileNameread-onlycurrentShadow Software File Name.
1.3.6.1.4.1.12394.1.2.2.3.1.9ColumnrbAuShadowSwVersionread-onlycurrentShadow Software Version.
1.3.6.1.4.1.12394.1.2.2.3.1.10ColumnrbAuRunningSoftwareread-onlycurrentCurrent running software.
1.3.6.1.4.1.12394.1.2.2.3.1.11ColumnrbAuUnitControlread-writecurrentIf reset (2) is selected, the AU should perform reset and resume running from the current version. Reset is applicable only for an installed AU, and it does no…
1.3.6.1.4.1.12394.1.2.2.3.1.12ColumnrbAuOperVersionValidityread-onlycurrentThe validity of the Operational (Main) Software. Not supported in current version.
1.3.6.1.4.1.12394.1.2.2.3.1.13ColumnrbAuShadowVersionValidityread-onlycurrentThe validity of the Shadow Software. Not supported in current version.
1.3.6.1.4.1.12394.1.2.2.3.1.14ColumnrbAuSetDefaultsread-writecurrentThis parameter defines the way 'Default Group' parameters are initialised with default values: 1 - Default values should not be copied to the Flash Memory, 2 -…
1.3.6.1.4.1.12394.1.2.2.3.1.15ColumnrbAuIduHwConfigDescriptionread-onlycurrentAU IDU Hardware configuration description
1.3.6.1.4.1.12394.1.2.2.3.1.16ColumnrbAuOduHwConfigDescriptionread-onlycurrentAU ODU Hardware configuration description. Not applicable for Version 2 and higher. For Version 2 it should return the value for the ODU connected to Channel 1.
1.3.6.1.4.1.12394.1.2.2.3.1.17ColumnrbAuUpgradeSwFileNameread-writecurrentThe name of the software file that should be used to upgrade AU software
1.3.6.1.4.1.12394.1.2.2.3.1.18ColumnrbAuOduHwRevisionread-onlycurrentAU ODU Hardware revision. Not applicable for Version 2 and higher. For Version 2 it should return the value for the ODU connected to Channel 1.
1.3.6.1.4.1.12394.1.2.2.3.1.19ColumnrbAuMaxNumberOfCallsread-writecurrentThe maximum number of voice calls supported by AU.
1.3.6.1.4.1.12394.1.2.2.3.1.20ColumnrbAuNumberOfRegisteredSUsread-onlycurrentThe number of registered SUs currently connected to this AU.
1.3.6.1.4.1.12394.1.2.2.3.1.21ColumnrbAuAirInterfaceTyperead-onlycurrentAU Operation Mode. typeA (1) - Standard Operation Mode, typeSi (2) - Advance Si Operation Mode.
1.3.6.1.4.1.12394.1.2.2.3.1.22ColumnrbAuCumulativePowerOnTimeread-onlycurrentCumulative Power On Time (minutes). Agent will return 0 if Cumulative Power On Time is unknown.
1.3.6.1.4.1.12394.1.2.2.3.1.23ColumnrbAuBeStarvationProtectLevelCurrentread-onlydeprecatedNot supported in current version. The Starvation Protection Level in Kbps for Best Effort connections. The system will maintain the throughput of all BE connec…
1.3.6.1.4.1.12394.1.2.2.3.1.24ColumnrbAuBeStarvationProtectLevelConfigread-writedeprecatedNot supported in current version. The configured Starvation Protection Level in Kbps for Best Effort connections. Will take effect (become current) after next …
1.3.6.1.4.1.12394.1.2.2.3.1.25ColumnrbAuNrtStarvationProtectLevelCurrentread-onlydeprecatedNot supported in current version. The Starvation Protection Level in Kbps for Non Real Time connections. The system will maintain the throughput of all NRT con…
1.3.6.1.4.1.12394.1.2.2.3.1.26ColumnrbAuNrtStarvationProtectLevelConfigread-writedeprecatedNot supported in current version. The configured Starvation Protection Level in Kbps for Best Effort connections. Will take effect (become current) after next …
1.3.6.1.4.1.12394.1.2.2.3.1.27ColumnrbAuActiveVoiceCallsread-onlycurrentThe number of active voice calls in the sector. Actual range is from 0 to the value defined by rbAuMaxNumberOfCalls.
1.3.6.1.4.1.12394.1.2.2.3.1.28ColumnrbAuSuUpgradeSwFileNameread-writecurrentThe name of the software file that should be used to upgrade SU software upon network entry for all SUs in this sector. Not applicable for any SU whose rbSuUpg…
1.3.6.1.4.1.12394.1.2.2.3.1.29ColumnrbAuSuUpgradeSwActionread-writecurrentThe Action that should be performed by SUs in this sector upon the Network Entry. Action should be performed using the rbAuSuUpgradeSwFileName. Not applicable …
1.3.6.1.4.1.12394.1.2.2.3.1.30ColumnrbAuClearAllSuSwUpgradeParamsread-writecurrentClears the SW Upgrade parameters for all SUs in the sector: For all SUs, rbSuUpgradeSwFileName will be set to an empty string, and rbSuUnitControl will be set …
1.3.6.1.4.1.12394.1.2.2.3.1.31ColumnrbAuDiversityModeread-writecurrentThe diversity mode used by the AU: noDiversity (1): No diversity (multi-channels). secondOrder (2): Second order diversity using channels 1 and 2. fourthOrder …
1.3.6.1.4.1.12394.1.2.2.6NoderbAcuConfiguration
1.3.6.1.4.1.12394.1.2.2.6.1ScalarrbAcuOperStatusread-onlycurrentAir Ventilation Unit operational status.
1.3.6.1.4.1.12394.1.2.2.6.2ScalarrbAcuFaultStatusread-onlycurrentAir Ventilation Unit fault status : each octet is representing one of 10 AVU fans: 1 - unit is OK, 2 - unit failed, 3 - unit is not installed
1.3.6.1.4.1.12394.1.2.2.6.3ScalarrbAcuLedStatusread-onlycurrentAir Ventilation Unit Leds Status: Each byte represents the single Led. Within each byte, bits 0-3 are the color, 4-7 are the blink rate. Supported color codes:…
1.3.6.1.4.1.12394.1.2.2.7TablerbPsuConfigTablenot-accessiblecurrentThis table provides Power Supply Unit configuration parameters
1.3.6.1.4.1.12394.1.2.2.7.1RowrbPsuConfigEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.2.7.1.1ColumnrbPsuNumberread-onlycurrentPhysical placement of the PSU.
1.3.6.1.4.1.12394.1.2.2.7.1.2ColumnrbPsuStatusread-onlycurrentPSU fault status.
1.3.6.1.4.1.12394.1.2.2.8TablerbPiuConfigTablenot-accessiblecurrentThis table provides Power Interface Unit configuration parameters.
1.3.6.1.4.1.12394.1.2.2.8.1RowrbPiuConfigEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.2.8.1.1ColumnrbPiuNumberread-onlycurrentPhysical placement of the PIU.
1.3.6.1.4.1.12394.1.2.2.8.1.2ColumnrbPiuStatusread-onlycurrentPIU fault status.
1.3.6.1.4.1.12394.1.2.2.8.1.3ColumnrbPiuModeread-onlycurrentPIU mode.
1.3.6.1.4.1.12394.1.2.2.9TablerbAuHwComponentsInfoTablenot-accessiblecurrentThis table provides parameters information regarding the AU Hardware components.
1.3.6.1.4.1.12394.1.2.2.9.1RowrbAuHwComponentsInfoEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.2.9.1.1ColumnrbAuIduIfCardRevisionread-onlycurrentAU-IDU IF Card Revision.
1.3.6.1.4.1.12394.1.2.2.9.1.2ColumnrbAuIduIfCardConfigurationread-onlycurrentAU-IDU IF Card Configuration description.
1.3.6.1.4.1.12394.1.2.2.9.1.3ColumnrbAuIduBootVersionread-onlycurrentAU-IDU Boot Version.
1.3.6.1.4.1.12394.1.2.2.9.1.4ColumnrbAuOduHC08Versionread-onlycurrentAU ODU HC08 Version. Not applicable for Version 2 and higher. For Version 2 it should return the value for the ODU connected to Channel 1.
1.3.6.1.4.1.12394.1.2.2.9.1.5ColumnrbAuOduCpldVersionread-onlycurrentAU ODU Cpld Version. Not applicable for Version 2 and higher. For Version 2 it should return the value for the ODU connected to Channel 1.
1.3.6.1.4.1.12394.1.2.2.9.1.6ColumnrbAuOduCardSerialNumberread-onlycurrentAU ODU serial number. Not applicable for Version 2 and higher. For Version 2 it should return the value for the ODU connected to Channel 1.
1.3.6.1.4.1.12394.1.2.2.9.1.7ColumnrbAuIduTyperead-onlycurrentAU-IDU Type. fourChannels and twoChannels-HP are not applicable in the current version.
1.3.6.1.4.1.12394.1.2.2.11TablerbChannelConfigTablenot-accessiblecurrentThis table provides Channel configuration parameters. This is a static Table. Only Update allowed.
1.3.6.1.4.1.12394.1.2.2.11.1RowrbChannelConfigEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.2.11.1.1ColumnrbChannelIdread-onlycurrentChannel ID. For two-channels AU-IDU only Channel ID 1-2 are supported.
1.3.6.1.4.1.12394.1.2.2.11.1.2ColumnrbChannelAssociatedRadioClusterIdread-onlycurrentChannel Associated Radio Cluster ID, as defined in the Associated ODU. Agent will return 0 if Associated Radio Cluster ID is unknown.
1.3.6.1.4.1.12394.1.2.2.11.1.3ColumnrbChannelAssociatedOduIdread-writecurrentChannel Associated ODU ID. Valid values: 1 to 24 or 0 to disassociate. Agent will return 0 if Associated ODU ID is unknown.
1.3.6.1.4.1.12394.1.2.2.11.1.4ColumnrbChannelTxFrequencyread-onlycurrentThe current Channel Tx Frequency (MHz). Agent will return 0 if Tx Frequency is unknown.
1.3.6.1.4.1.12394.1.2.2.11.1.5ColumnrbChannelRxFrequencyread-onlycurrentChannel Rx Frequency (MHz). Calculated from the Tx Frequency according to the parameters of the Configured Frequency Band in the Associated ODU. Agent will ret…
1.3.6.1.4.1.12394.1.2.2.11.1.6ColumnrbChannelAdminStatusread-writecurrentChannel Administrative Status. Valid values: 1 to 2 Agent will return 0 if Admin Status is unknown. For AUs using diversity (rbAuDiversityMode other than noDiv…
1.3.6.1.4.1.12394.1.2.2.11.1.7ColumnrbChannelConfiguredTxFrequencyread-writecurrentThe configured Channel Tx Frequency (MHz). Available values depend on Bandwidth and parameters of the Configured Frequency Band in the Associated ODU. For AUs …
1.3.6.1.4.1.12394.1.2.2.11.1.8ColumnrbChannelOduActualFrequencyBandread-onlycurrentOdu Actual Frequency Band ID. Must be one of the Frequency Band IDs available in the Frequency Bands Table. Agent will return 0 if Frequency Band is unknown.
1.3.6.1.4.1.12394.1.2.2.11.1.9ColumnrbChannelOperStatusread-onlycurrentChannel Operational Status. Agent will return 0 if Oper Status is unknown.
1.3.6.1.4.1.12394.1.2.5NoderbSubcriberUnitConfig
1.3.6.1.4.1.12394.1.2.5.1TablerbRegisteredSuTablenot-accessiblecurrentThis table contains information on SUs registered in the system. It includes also SUs that are defined but are not registered currently. It can also be used to…
1.3.6.1.4.1.12394.1.2.5.1.1RowrbRegisteredSuEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.5.1.1.1ColumnrbAuIdread-onlycurrentThe slot number of the AU to which the SU is connected. For a Micro Base Station AU ID is 1. If the SU is still not registered - AU ID is 255.
1.3.6.1.4.1.12394.1.2.5.1.1.2ColumnrbSuMacAddrread-onlycurrentThe MAC address of the SU. For registered SUs this parameter is read-only. The MAC address is read-write for SUs that are not registered, enabling pre-definiti…
1.3.6.1.4.1.12394.1.2.5.1.1.3ColumnrbSuIDread-onlycurrentSU ID. An index assigned by the serving device.
1.3.6.1.4.1.12394.1.2.5.1.1.4ColumnrbSuRegistrationStateread-onlycurrentThe registration state of the SU.
1.3.6.1.4.1.12394.1.2.5.1.1.5ColumnrbSuPersistenceread-writecurrentThe permanence status of the SU. A new SU that becomes registered at the Device, is automatically added to the database with a Temporary status. If the Device …
1.3.6.1.4.1.12394.1.2.5.1.1.6ColumnrbSuSerialNoread-onlycurrentSerial number assigned for the SU during the production time.
1.3.6.1.4.1.12394.1.2.5.1.1.7ColumnrbSuSysNameread-writecurrentThe SU's name. User Name in SUs using Advanced Si Operation Mode (Air Interface type Si)). Configurable (write) only for SUs running SW version 2.0 or higher a…
1.3.6.1.4.1.12394.1.2.5.1.1.8ColumnrbSuFaultStatusread-onlycurrentThe severity of the SU's fault. This is summarized information regarding the unit's healthiness.
1.3.6.1.4.1.12394.1.2.5.1.1.9ColumnrbSuHwRevisionread-onlycurrentHardware version of the SU's Main card.
1.3.6.1.4.1.12394.1.2.5.1.1.10ColumnrbSuOperSwFileNameread-onlycurrentOperational (Main) Software File Name.
1.3.6.1.4.1.12394.1.2.5.1.1.11ColumnrbSuOperSwVersionread-onlycurrentOperational (Main) Software Version.
1.3.6.1.4.1.12394.1.2.5.1.1.12ColumnrbSuShadowSwFileNameread-onlycurrentShadow Software File name.
1.3.6.1.4.1.12394.1.2.5.1.1.13ColumnrbSuShadowSwVersionread-onlycurrentShadow Software Version.
1.3.6.1.4.1.12394.1.2.5.1.1.14ColumnrbSuRunningSoftwareread-onlycurrentCurrent running software.
1.3.6.1.4.1.12394.1.2.5.1.1.15ColumnrbSuOperVersionValidityread-onlycurrentThe validity of the Operational (Main) Software.
1.3.6.1.4.1.12394.1.2.5.1.1.16ColumnrbSuShadowVersionValidityread-onlycurrentThe validity of the Shadow Software. Not supported in current version.
1.3.6.1.4.1.12394.1.2.5.1.1.17ColumnrbSuUnitControlread-writecurrentIf reset (2) is selected, the SU should perform reset and resume running from the current version. Reset is applicable only for a connected SU, and it does not…
1.3.6.1.4.1.12394.1.2.5.1.1.18ColumnrbSuSetDefaultsread-writecurrentThis parameter defines the way 'Default Group' parameters are initialised with default values: 1 - Default values should not be copied to the Flash Memory, 2 -…
1.3.6.1.4.1.12394.1.2.5.1.1.19ColumnrbSuAllowedUsersTyperead-writedeprecatedNot supported in current version.
1.3.6.1.4.1.12394.1.2.5.1.1.20ColumnrbSuAllowedQoSread-writedeprecatedNot supported in current version.
1.3.6.1.4.1.12394.1.2.5.1.1.21ColumnrbSuAllowedServiceread-writedeprecatedNot supported in current version.
1.3.6.1.4.1.12394.1.2.5.1.1.22ColumnrbSuRowStatusread-writecurrentControl for creating and deleting entries. Entries may be modified while active. active (1) - means that the entry is available for use by the managed device a…
1.3.6.1.4.1.12394.1.2.5.1.1.23ColumnrbSuInstallerPasswordread-writecurrentThe password that should be used when accessing the SU's Monitor program using Telnet via its Ethernet port.
1.3.6.1.4.1.12394.1.2.5.1.1.24ColumnrbSuHwConfigDescriptionread-onlycurrentThe Hardware configuration description of the SU's Main card.
1.3.6.1.4.1.12394.1.2.5.1.1.25ColumnrbSuUpgradeSwFileNameread-writecurrentThe name of the software file that should be used to upgrade SU software.
1.3.6.1.4.1.12394.1.2.5.1.1.26ColumnrbSuServiceTyperead-writedeprecatedNot supported in current version.
1.3.6.1.4.1.12394.1.2.5.1.1.27ColumnrbSuIduTyperead-onlycurrentThe type of SU IDU. In current version only basic (0) and ngData4Wireless (11) are supported.
1.3.6.1.4.1.12394.1.2.5.1.1.28ColumnrbSuExternalDevNumberread-onlycurrentThe number of gateways (including ngData4Wireless IDU) connected to SU. This includes only devices that support the DRAP protocol for registration at the Base …
1.3.6.1.4.1.12394.1.2.5.1.1.29ColumnrbSuServiceFaultBitMapread-onlycurrentThe reason for denying services to the SU. Bit 1: Loop problem. A loop was detected on the Ethernet side of the SU. rbNetworkingError Trap will be sent, and se…
1.3.6.1.4.1.12394.1.2.5.1.1.30ColumnrbSuCumulativePowerOnTimeread-onlycurrentCumulative Power On Time (minutes). Agent will return 0 if Cumulative Power On Time is unknown.
1.3.6.1.4.1.12394.1.2.5.1.1.31ColumnrbSuOrganizationNameread-onlycurrentSU's organization name as defined in the SU.
1.3.6.1.4.1.12394.1.2.5.1.1.32ColumnrbSuAddressread-onlycurrentThe SU's address as defined in the SU.
1.3.6.1.4.1.12394.1.2.5.1.1.33ColumnrbSuCountryread-onlycurrentThe SU's country as defined in the SU.
1.3.6.1.4.1.12394.1.2.5.1.1.34ColumnrbSuMACControlNumberread-onlycurrentLeast Significant Byte of the Integer computed by summarizing the values of the 12 hexadecimal digits of the MAC Address.
1.3.6.1.4.1.12394.1.2.5.1.1.35ColumnrbSuAirInterfaceTyperead-onlycurrentSU Operation Mode. typeA (1) - Standard Operation Mode, typeSi (2) - Advance Si Operation Mode.
1.3.6.1.4.1.12394.1.2.5.2TablerbSuSubDevicesTablenot-accessiblecurrentThis table contains IP Addresse of Gateways that support DRAP that are connected to SUs. To receive the Gateways connected to a specific SU, community <com>@SU…
1.3.6.1.4.1.12394.1.2.5.2.1RowrbSuSubDevicesEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.5.2.1.1ColumnrbSubDeviceIpAddressread-onlycurrentIP Address of the Gateway connected to an SU.
1.3.6.1.4.1.12394.1.2.5.2.1.2ColumnrbSuMacAddressread-onlycurrentMAC Address of the SU.
1.3.6.1.4.1.12394.1.2.5.2.1.3ColumnrbSubDeviceTyperead-onlycurrentThe type of Gateway.
1.3.6.1.4.1.12394.1.2.5.2.1.4ColumnrbSubDeviceVlanIDread-onlycurrentThe management VLAN ID used by the Gateway.
1.3.6.1.4.1.12394.1.2.5.3TablerbSuHwComponentsInfoTablenot-accessiblecurrentThis table provides parameters information regarding the SU Hardware components.
1.3.6.1.4.1.12394.1.2.5.3.1RowrbSuHwComponentsInfoEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.5.3.1.1ColumnrbSuRfCardRevisionread-onlycurrentSU RF Card Revision.
1.3.6.1.4.1.12394.1.2.5.3.1.2ColumnrbSuRfCardConfigurationread-onlydeprecatedSU RF Card Configuration description. Not supported in current version.
1.3.6.1.4.1.12394.1.2.5.3.1.3ColumnrbSuBootVersionread-onlycurrentSU Boot Version.
1.3.6.1.4.1.12394.1.2.5.3.1.4ColumnrbSuTyperead-onlycurrentSU Type.
1.3.6.1.4.1.12394.1.2.5.4NodesuBridgingParameters
1.3.6.1.4.1.12394.1.2.5.4.1ScalarrbSuSupportDevicesLimitread-writecurrentEnable\disable the limitation on the maximum number of Ethernet devices (MAC addresses) that can be supported by the SU. If disabled, then the maximum number i…
1.3.6.1.4.1.12394.1.2.5.4.2ScalarrbSuMaxNumberOfSupportedDevicesread-writecurrentMaximum number of devices supported by SU. This parameter can be changed only if rbSuSupportDevicesLimit is enabled.
1.3.6.1.4.1.12394.1.2.5.4.3ScalarrbSuBridgeAgingTimeread-writecurrentThe MAC Address aging time in minutes.
1.3.6.1.4.1.12394.1.2.5.5NoderbMACBehindSUList
1.3.6.1.4.1.12394.1.2.5.5.1TablerbMACBehindSUListTablenot-accessiblecurrentThis table provides information regarding the MAC Addresses and VLAN IDs of devices behind the SU.
1.3.6.1.4.1.12394.1.2.5.5.1.1RowrbMACBehindSUListEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.5.5.1.1.1ColumnrbMacBehindSuAddrread-onlycurrentMAC Address of a device behind the SU.
1.3.6.1.4.1.12394.1.2.5.5.1.1.2ColumnrbMacBehindSuVlanread-onlycurrentThe VLAN ID used by the device (a device may use more than one VLAN ID, or none. If more than one VLAN ID is used, this will be the first identified VLAN ID).
1.3.6.1.4.1.12394.1.2.5.6NoderbSiSuInfo
1.3.6.1.4.1.12394.1.2.5.6.1TablerbSiSuInfoTablenot-accessiblecurrentThis table provides parameters information regarding the Self-Install SU.
1.3.6.1.4.1.12394.1.2.5.6.1.1RowrbSiSuInfoEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.5.6.1.1.1ColumnrbSiSuAntennaSelectionread-onlycurrentThe antenna(s) that can be used in the SI CPE.
1.3.6.1.4.1.12394.1.2.5.6.1.1.2ColumnrbSiSuSmartCardStatusread-onlycurrentThe Smart card status.
1.3.6.1.4.1.12394.1.2.5.6.1.1.3ColumnrbSiSuInterfaceTyperead-onlycurrentThe interface type.
1.3.6.1.4.1.12394.1.2.5.7NoderbSuLicenses
1.3.6.1.4.1.12394.1.2.5.7.1TablerbSuLicensesTablenot-accessiblecurrentThis table provides information about License(s) registered for the SU. It will include up to 5 entries - Maximum License Count per SU. This table will only be…
1.3.6.1.4.1.12394.1.2.5.7.1.1RowrbSuLicensesEntrynot-accessiblecurrentTable entry.
1.3.6.1.4.1.12394.1.2.5.7.1.1.1ColumnrbSuLicenseIdxread-onlycurrentSU License Table Index.
1.3.6.1.4.1.12394.1.2.5.7.1.1.2ColumnrbSuLicenseIdread-writecurrentSU License ID. Currently the only supported value is 1 for Bandwidth.
1.3.6.1.4.1.12394.1.2.5.7.1.1.3ColumnrbSuLicenseValueread-writecurrentSU License Value. Currently the only supported value is 0 for Unlimited Bandwidth.
1.3.6.1.4.1.12394.1.2.6NoderbAuthorizationAndTraps
1.3.6.1.4.1.12394.1.2.6.1TablerbAuthorizedManagersTablenot-accessiblecurrentThis table defines the stations that are authorized to manage the device. Up to 10 Authorized Managers can be defined.
1.3.6.1.4.1.12394.1.2.6.1.1RowrbAuthorizedManagersEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.6.1.1.1ColumnauthMngrIpAddrread-writecurrentIP address of the Authorized Management Station
1.3.6.1.4.1.12394.1.2.6.1.1.2ColumnauthMngrReadCommunityread-writecurrentAuthorized Management Station Community for Read operations. In case that trap transmission is enabled, trap message is send with this community.
1.3.6.1.4.1.12394.1.2.6.1.1.3ColumnauthMngrWriteCommunityread-writecurrentAuthorized Management Station Community for Write operations.
1.3.6.1.4.1.12394.1.2.6.1.1.4ColumnauthMngrTrapEnableread-writecurrentWhen set to enable, device transmits trap to the Authorized Manager.
1.3.6.1.4.1.12394.1.2.6.1.1.5ColumnauthMngrRowStatusread-writecurrentControl for creating and deleting entries. Entries may be modified while active. active (1) - means that the entry is available for use by the managed device a…
1.3.6.1.4.1.12394.1.2.6.2TablerbTrapConfigTablenot-accessiblecurrentThis table defines configuration parameters for each trap supported by device.
1.3.6.1.4.1.12394.1.2.6.2.1RowrbTrapConfigEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.6.2.1.1ColumntrapEnterprizeIdread-onlycurrentIdentification of the MIB where the trap is defined.
1.3.6.1.4.1.12394.1.2.6.2.1.2ColumntrapIdread-onlycurrentTrap ID defined in the TRAP-TYPE macro in the corresponding MIB. For snmp trapEnterprizedId: 1 - coldStart , 2 - warmStart , 3 - linkDown , 4 - linkUp , 5 - au…
1.3.6.1.4.1.12394.1.2.6.2.1.3ColumntrapEnableread-writecurrentEnable/disable transmission of the trap.
1.3.6.1.4.1.12394.1.2.6.2.1.4ColumntrapSeverityread-writecurrentTrap severity.
1.3.6.1.4.1.12394.1.2.6.2.1.5ColumntrapSuppressionIntervalread-writecurrentThe interval in seconds during which transmission of identical traps should be supressed by the device. 0 means trap suppression is disabled.
1.3.6.1.4.1.12394.1.2.6.3ScalarrbTrapGetActiveread-writecurrentThis parameter is used to obtain active alarms from device. When set to enable, the device respond by transmitting all currently active alarms.
1.3.6.1.4.1.12394.1.2.6.4ScalarrbTrapSeqNumberread-writecurrentThis parameter is used as trap variable binding and contains the sequential trap number. Get of this variable should return the number of the last trap transmi…
1.3.6.1.4.1.12394.1.2.6.5ScalarrbTrapSeverityread-onlycurrentThis parameter is used as trap variable binding and contains the severity of the trap.
1.3.6.1.4.1.12394.1.2.6.6ScalarrbTrapSourceread-onlycurrentThis parameter is used as trap variable binding and contains the trap source entity : <NPU.Slot#>, <AU.Slot#>, <SU.MacAddress>, <BS>, <PSU#>, <PIU#>, <ACU#>, <…
1.3.6.1.4.1.12394.1.2.6.7ScalarrbTrapAdditionalInforead-onlycurrentThis parameter is used as trap variable binding and contains the additional info, transmitted with the trap.
1.3.6.1.4.1.12394.1.2.6.8ScalarrbTrapCategoryread-onlycurrentThe trap category according to the X.733.
1.3.6.1.4.1.12394.1.2.6.9ScalarrbTrapMinSeverityread-onlycurrentThis parameter defines the minimum severity of traps to be transmitted by device. Not supported in current version.
1.3.6.1.4.1.12394.1.2.6.10ScalarrbTrapLedStatusread-onlycurrentThis parameter defines status of the leds of corresponding device. Not supported in current version.
1.3.6.1.4.1.12394.1.2.6.11ScalarrbTrapIpAddressread-onlycurrentThis parameter is used as a trap variable binding in case that IP Address should be transmitted.
1.3.6.1.4.1.12394.1.2.6.12ScalarrbTrapSetFailureReasonread-onlycurrentThis parameter contains the reason the Set parameter command was rejected by device
1.3.6.1.4.1.12394.1.2.6.13ScalarrbTrapRestoreDefaultsread-writecurrentThis parameter is used to restore the default values of the configuration parameters for each trap supported by device: restoreTrapEnable (1) - means that the …
1.3.6.1.4.1.12394.1.2.6.20TablerbTrapThresholdsTablenot-accessiblecurrentThis table defines thresholds for specific counters. Trap is transmitted if counter passes the threshold. Not supported in current version.
1.3.6.1.4.1.12394.1.2.6.20.1RowrbTrapThresholdsEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.6.20.1.1ColumncounterIdread-writecurrentIdentification of the counter
1.3.6.1.4.1.12394.1.2.6.20.1.2ColumncounterNameread-writecurrentString representing the name of the counter, as it is defined in the MIB
1.3.6.1.4.1.12394.1.2.6.20.1.3ColumncounterTyperead-writecurrentType of the counter
1.3.6.1.4.1.12394.1.2.6.20.1.4ColumncounterIntValueread-writecurrentCounter value in Integer format
1.3.6.1.4.1.12394.1.2.6.20.1.5ColumncounterStringValueread-writecurrentCounter value in String format
1.3.6.1.4.1.12394.1.2.6.21TablerbTrapEventLogTablenot-accessiblecurrentThis table containes trap information for the last 1000 traps.
1.3.6.1.4.1.12394.1.2.6.21.1RowrbTrapEventLogEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.6.21.1.1ColumntrapEventLogSeqNumread-onlycurrentThe trap sequential number.
1.3.6.1.4.1.12394.1.2.6.21.1.2ColumntrapEventLogIdread-onlycurrentThe trap ID defined in the TRAP-TYPE macro.
1.3.6.1.4.1.12394.1.2.6.21.1.3ColumntrapEventLogSeverityread-onlycurrentThe trap severity.
1.3.6.1.4.1.12394.1.2.6.21.1.4ColumntrapEventLogTyperead-onlycurrentTrap ID defined in the TRAP-TYPE macro: 0 to 5 for the snmp MIB or 6 for other MIBs.
1.3.6.1.4.1.12394.1.2.6.21.1.5ColumntrapEventLogCategoryread-onlycurrentThe trap category according to the X.733.
1.3.6.1.4.1.12394.1.2.6.21.1.6ColumntrapEventLogSourceread-onlycurrentTrap source entity : <NPU.Slot#>, <AU.Slot#>, <SU.MacAddress>, <BS>, <PSU#>, <PIU#>, <ACU#>, <ACU-FAN.Slot#>, <RC.RadioClusterId#>, <ODU.OduConfigId#>, <CHNL.A…
1.3.6.1.4.1.12394.1.2.6.21.1.7ColumntrapEventLogVarBindNumberread-onlycurrentThe trap Variable Bind Number.
1.3.6.1.4.1.12394.1.2.6.21.1.8ColumntrapEventLogVarBindSizeread-onlycurrentThe trap Variable Bind Size.
1.3.6.1.4.1.12394.1.2.6.21.1.9ColumntrapEventLogAddVarAttributesread-onlycurrentThe trap Variable Attributes Additional information.
1.3.6.1.4.1.12394.1.2.6.21.1.10ColumntrapEventLogDateAndTimeread-onlycurrentThe trap Date And Time.
1.3.6.1.4.1.12394.1.2.6.22TablerbTrapAlarmLogTablenot-accessiblecurrentThis table containes trap information for all alarms. For traps that are not active the trapAlarmLogAddVarAttributes is NA.
1.3.6.1.4.1.12394.1.2.6.22.1RowrbTrapAlarmLogEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.6.22.1.1ColumntrapAlarmLogAlarmIdread-onlycurrentThe alarm type.
1.3.6.1.4.1.12394.1.2.6.22.1.2ColumntrapAlarmLogSourceread-onlycurrentThe alarm source.
1.3.6.1.4.1.12394.1.2.6.22.1.3ColumntrapAlarmLogSlotIdread-onlycurrentThe alarm card slot id. Slot 5-6 are allowed for NPU card, although in the current version NPU can be used only in slot 5. Slots 1-4, 7-9 are allowed for AU ca…
1.3.6.1.4.1.12394.1.2.6.22.1.4ColumntrapAlarmLogEventIdread-onlycurrentThe trap ID defined in the TRAP-TYPE macro. For standard SNMP traps, the proprietary trap IDs are: ColdStart - 128 WarmStart - 129 LinkDown - 130 LinkUp - 131 …
1.3.6.1.4.1.12394.1.2.6.22.1.5ColumntrapAlarmLogNameread-onlycurrentThe representing trap name.
1.3.6.1.4.1.12394.1.2.6.22.1.6ColumntrapAlarmLogSeverityread-onlycurrentThe trap severity.
1.3.6.1.4.1.12394.1.2.6.22.1.7ColumntrapAlarmLogCategoryread-onlycurrentThe trap category according to the X.733.
1.3.6.1.4.1.12394.1.2.6.22.1.8ColumntrapAlarmLogStrOnread-onlycurrentThe representing trap string.
1.3.6.1.4.1.12394.1.2.6.22.1.9ColumntrapAlarmLogVarBindNumberread-onlycurrentThe trap Variable Bind Number.
1.3.6.1.4.1.12394.1.2.6.22.1.10ColumntrapAlarmLogVarBindSizeread-onlycurrentThe trap Variable Bind Size.
1.3.6.1.4.1.12394.1.2.6.22.1.11ColumntrapAlarmLogAddVarAttributesread-onlycurrentThe trap Variable Attributes Additional information. NA is used for inactive Alarms.
1.3.6.1.4.1.12394.1.2.6.22.1.12ColumntrapAlarmLogLedread-onlycurrentThe NPU LEDs associated with alarm. Not applicable for current version.
1.3.6.1.4.1.12394.1.2.7NoderbInterfaces
1.3.6.1.4.1.12394.1.2.7.1NoderbEthernetInterface
1.3.6.1.4.1.12394.1.2.7.1.1TablerbEthIfConfigTablenot-accessiblecurrentThis table contains Ethernet interface configuration parameters. To receive the Ethernet Interface configuration to a specific SU, community <com>@SU.<MacAddre…
1.3.6.1.4.1.12394.1.2.7.1.1.1RowrbEthIfConfigEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.7.1.1.1.1ColumnethConfigIfIndexread-onlycurrentIndex of Ethernet Interface. In NPU and Micro Base Station, 1 is for the DATA port and 2 is for the MGMT port. In SU, 1 is for the ETHERNET port and 2 is not a…
1.3.6.1.4.1.12394.1.2.7.1.1.1.2ColumnethConfigAutoNegotiationread-writecurrentThe Auto Negotiation mode that will be active after the reset. Not applicable for NPU ports.
1.3.6.1.4.1.12394.1.2.7.1.1.1.3ColumnethConfigLinkSpeedAndDuplexread-writecurrentThe configured Speed and Duplex that will be in effect after the next reset. Applicable only if Auto Negotiation is Disabled. The applicable options are: In NP…
1.3.6.1.4.1.12394.1.2.7.1.1.1.4ColumnethConfigCurrentdAutoNegotiationread-onlycurrentThe current Auto Negotiation mode (enabled/disabled). In NPU, DATA port is always disabled, MGMT port is always enabled.
1.3.6.1.4.1.12394.1.2.7.1.1.1.5ColumnethConfigCurrentLinkSpeedAndDuplexread-onlycurrentWhen Auto Negotiation is disabled, this is the current Speed and Duplex. When Auto Negotiation is enabled, this is the detected Speed and Duplex.
1.3.6.1.4.1.12394.1.2.7.2NoderbAirInterface
1.3.6.1.4.1.12394.1.2.7.2.1NoderbAuMacParameters
1.3.6.1.4.1.12394.1.2.7.2.1.1ScalarrbAuBaseStationIdread-onlycurrentThe current Base Station ID. The Base Station ID consists of 6 octets. The first 3 octets are the Operator ID, the next two octets are the Cell ID and the sixt…
1.3.6.1.4.1.12394.1.2.7.2.1.2ScalarrbAuMaxCellRadiusread-writecurrentThe maximum cell radius (the distance of the farthest SU that should be served by the base station)in km. The defaults are BW=1.75MHz, Max Cell Radius = 10 to …
1.3.6.1.4.1.12394.1.2.7.2.1.3ScalarrbAuConfiguredBaseStationIdread-writecurrentUnique Base Station ID that will be in use after the reset. For version 2.0 and higher this is a read only parameter.
1.3.6.1.4.1.12394.1.2.7.2.1.4ScalarrbAuARQStateread-onlycurrentCurrent ARQ state.
1.3.6.1.4.1.12394.1.2.7.2.1.5ScalarrbAuConfiguredARQStateread-writecurrentARQ state that will be in effect after the next reset.
1.3.6.1.4.1.12394.1.2.7.2.1.6ScalarrbAuConfiguredSectorIdread-writecurrentUnique AU Sector ID.
1.3.6.1.4.1.12394.1.2.7.2.1.7ScalarrbAuCurrentMaxCellRadiusread-onlycurrentThe maximum cell radius supported by the AU, in km.
1.3.6.1.4.1.12394.1.2.7.2.2NoderbSuMacParameters
1.3.6.1.4.1.12394.1.2.7.2.2.1ScalarrbSuBaseStationIdread-onlycurrentThe current Base Station ID. Together with rbSuBaseStationIdMask it defines the AUs to which the SU is allowed to connect.
1.3.6.1.4.1.12394.1.2.7.2.2.2ScalarrbSuBaseStationIdMaskread-onlycurrentThe matching criteria for the define Base Station Id.
1.3.6.1.4.1.12394.1.2.7.2.2.3ScalarrbSuConfiguredBaseStationIdread-writecurrentThe Base Station ID that will be in use after the next reset.
1.3.6.1.4.1.12394.1.2.7.2.2.4ScalarrbSuConfiguredBaseStationIdMaskread-writecurrentThe matching criteria for the define Base Station Id that will be in use after the next reset.
1.3.6.1.4.1.12394.1.2.7.2.3NoderbAuMultirateParameters
1.3.6.1.4.1.12394.1.2.7.2.3.1ScalarrbAuMultirateSupportread-writecurrentThis parameter defines if Multi-rate mechanism is supported by AU. After each reset AU boots with Multirate Support enabled.
1.3.6.1.4.1.12394.1.2.7.2.3.2ScalarrbAuUlBasicRateread-writecurrentThe lowest modulation SU will use.
1.3.6.1.4.1.12394.1.2.7.2.3.3ScalarrbAuDlBasicRateread-writecurrentThe lowest modulation AU will use.
1.3.6.1.4.1.12394.1.2.7.2.3.4ScalarrbAuUlMinNoOfSubChannelsread-writecurrentApplicable only if the Uplink Basic Rate is BPSK 1/2 (rbAuUlBasicRate is 1). The Minimum Number of Subchannels to be used by the Multi Rate algorithm in the Up…
1.3.6.1.4.1.12394.1.2.7.2.4NoderbAuATPCParameters
1.3.6.1.4.1.12394.1.2.7.2.4.1ScalarrbAuATPCSupportread-writecurrentThis parameter defines if ATPC mechanism is supported by AU. After each reset AU boots with ATPC enabled. For version 2.0 and higher this is a read-only parame…
1.3.6.1.4.1.12394.1.2.7.2.4.2ScalarrbAuOptimalRSSIread-writecurrentThe RSSI in dBm required from all SUs. For version 2.0 and higher this is a read-only parameter.
1.3.6.1.4.1.12394.1.2.7.2.5NoderbSuMultirateParameters
1.3.6.1.4.1.12394.1.2.7.2.5.1ScalarrbSuTxPowerread-onlycurrentThe last transmit power in dBm.
1.3.6.1.4.1.12394.1.2.7.2.5.3ScalarrbSuUlSNRread-onlycurrentThe SNR in dB of the last burst received from the SU.
1.3.6.1.4.1.12394.1.2.7.2.5.4ScalarrbSuUlRSSIread-onlycurrentThe RSSI in dBm of the last burst received from the SU.
1.3.6.1.4.1.12394.1.2.7.2.5.5ScalarrbSuUlCurrentRateread-writecurrentThe last uplink rate used by the Multirate mechanism. When Multirate is enabled, this parameter is read-only. If Multirate in the AU is disabled, this paramete…
1.3.6.1.4.1.12394.1.2.7.2.5.6ScalarrbSuDlSNRread-onlycurrentThe SNR in dB of the last burst received by the SU.
1.3.6.1.4.1.12394.1.2.7.2.5.7ScalarrbSuDlRSSIread-onlycurrentThe RSSI in dBm of the last burst received by the SU.
1.3.6.1.4.1.12394.1.2.7.2.5.8ScalarrbSuDlCurrentRateread-writecurrentThe last downlink rate used by the Multirate mechanism. When Multirate is enabled, this parameter is read-only. If Multirate in the AU is disabled, this parame…
1.3.6.1.4.1.12394.1.2.7.2.5.9ScalarrbSuMultirateSupportread-onlycurrentThis parameter indicates if Multi-rate mechanism is used by associated AU.
1.3.6.1.4.1.12394.1.2.7.2.5.10ScalarrbSuEstDistanceread-onlycurrentThe estimated distance in meters from the Base Station (rounded to 100 meters). Agent will return 0 if distance is unknown.
1.3.6.1.4.1.12394.1.2.7.2.5.11ScalarrbSuUlSNRValueread-onlycurrentThe SNR in tenth dB units of the last burst received from the SU.
1.3.6.1.4.1.12394.1.2.7.2.5.12ScalarrbSuUlRSSIValueread-onlycurrentThe RSSI in tenth dBm units of the last burst received from the SU.
1.3.6.1.4.1.12394.1.2.7.2.5.13ScalarrbSuDlSNRValueread-onlycurrentThe SNR in thenth dB units of the last burst received by the SU.
1.3.6.1.4.1.12394.1.2.7.2.5.14ScalarrbSuDlRSSIValueread-onlycurrentThe RSSI in tenth dBm units of the last burst received by the SU.
1.3.6.1.4.1.12394.1.2.7.2.6NoderbSuATPCParameters
1.3.6.1.4.1.12394.1.2.7.2.6.1ScalarrbSuATPCSupportread-onlycurrentIndicates whether ATPC is used by the SU. Typically this is controlled by the AU/Micro Base Station. ATPC can be disabled locally (via the Ethernet port of the…
1.3.6.1.4.1.12394.1.2.7.2.7NoderbAuPhyParameters
1.3.6.1.4.1.12394.1.2.7.2.7.1ScalarrbAuCurrentPhyBandwidthread-onlycurrentThis parameter defines the current operating bandwidth.
1.3.6.1.4.1.12394.1.2.7.2.7.2ScalarrbAuPhyTxFrequencyChannelread-onlycurrentNot applicable for Version 2 and higher. This parameter defines central channel frequency in MHz.
1.3.6.1.4.1.12394.1.2.7.2.7.3ScalarrbAuPhyTxConfiguredFrequencyChannelread-writecurrentNot applicable for Version 2 and higher. This parameter defines central channel frequency in MHz.
1.3.6.1.4.1.12394.1.2.7.2.7.4ScalarrbAuConfiguredPhyBandwidthread-writecurrentb175 (1): 1.75 MHz b35 (2): 3.5 MHz b50 (3): 5 MHz b70 (4): 7 MHz b100 (5): 10 MHz The actually available bandwidths depend on the AU's hardware and SW version…
1.3.6.1.4.1.12394.1.2.7.2.8TablerbAuOutdoorConfigTablenot-accessibledeprecatedThis table is deprecated from version 2.0. This table contains AU PHY Configuration Parameters per Outdoor unit.
1.3.6.1.4.1.12394.1.2.7.2.8.1RowrbAuOutdoorConfigEntrynot-accessibledeprecatedTable entry
1.3.6.1.4.1.12394.1.2.7.2.8.1.1ColumnauOutdoorUnitIndexread-onlydeprecatedIndex of outdoor unit.
1.3.6.1.4.1.12394.1.2.7.2.8.1.2ColumnauFrequencyBandread-onlydeprecatedThis parameter defines frequency band.
1.3.6.1.4.1.12394.1.2.7.2.8.1.3ColumnauTxPowerread-writedeprecatedWorking Transmit Power in dBm. The Min is 13 dBm, the Max is 28 dBm.
1.3.6.1.4.1.12394.1.2.7.2.9NoderbSuPhyParameters
1.3.6.1.4.1.12394.1.2.7.2.9.1ScalarsuPhyCurrentBandwidthread-onlycurrentb175 (1): 1.75 MHz b35 (2): 3.5 MHz b50 (3): 5 MHz b70 (4): 7 MHz b100 (5): 10 MHz The actually available bandwidths depend on the SU's hardware and SW version…
1.3.6.1.4.1.12394.1.2.7.2.9.2ScalarsuPhyCurrentTxFrequencyChannelread-onlycurrentThis parameter defines the current central channel frequency in MHz.
1.3.6.1.4.1.12394.1.2.7.2.9.3ScalarsuPhyConfiguredBandwidthread-writecurrentThis parameter defines the configured bandwidth, that will be in effect after the next reset.
1.3.6.1.4.1.12394.1.2.7.2.9.4ScalarsuPhyConfiguredTxFrequencyChannelread-writecurrentThis parameter defines central channel frequency in MHz. In version 2.0 and higher the available values depend on the Bandwidth and on the applicable Frequency…
1.3.6.1.4.1.12394.1.2.7.2.10NoderbSuBestBstAuParams
1.3.6.1.4.1.12394.1.2.7.2.10.1TablerbSuBestBstAuParamsTablenot-accessiblecurrentThis table provides parameters information regarding the Best BST/AU Configuration and Status.
1.3.6.1.4.1.12394.1.2.7.2.10.1.1RowrbSuBestBstAuParamsEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.7.2.10.1.1.1ColumnrbSuCurrentBestBstAuSupportread-onlycurrentEnable/Disable the feature - current value.
1.3.6.1.4.1.12394.1.2.7.2.10.1.1.2ColumnrbSuConfiguredBestBstAuSupportread-writecurrentEnable/Disable the feature - configured value.
1.3.6.1.4.1.12394.1.2.7.2.10.1.1.3ColumnrbSuCurrentPreferredBstAuIdread-onlycurrentDefine the base ID for the preferred BST/AU - current value.
1.3.6.1.4.1.12394.1.2.7.2.10.1.1.4ColumnrbSuConfiguredPreferredBstAuIdread-writecurrentDefine the base ID for the preferred BST/AU - configured value.
1.3.6.1.4.1.12394.1.2.7.2.10.1.1.5ColumnrbSuCurrentPreferredBstAuMaskread-onlycurrentThe ID mask that together with the Preferred BST/AU ID defines a range of preferred BST/AUs - current value.
1.3.6.1.4.1.12394.1.2.7.2.10.1.1.6ColumnrbSuConfiguredPreferredBstAuMaskread-writecurrentThe ID mask that together with the Preferred BST/AU ID defines a range of preferred BST/AUs - configured value.
1.3.6.1.4.1.12394.1.2.7.2.10.1.1.7ColumnrbSuSelectedBstAuread-onlycurrentThe selected BST/AU ID.
1.3.6.1.4.1.12394.1.2.7.2.10.1.1.8ColumnrbSuSelectedRxFrequencyread-onlycurrentThe selected Rx Frequency, in MHz.
1.3.6.1.4.1.12394.1.2.7.2.10.1.1.9ColumnrbSuSelectedTxFrequencyread-onlycurrentThe selected Tx Frequency, in MHz.
1.3.6.1.4.1.12394.1.2.7.2.10.1.1.10ColumnrbSuCurrentBstAuIdread-onlycurrentDefine the base ID for the BST/AU - current value.
1.3.6.1.4.1.12394.1.2.7.2.10.1.1.11ColumnrbSuConfiguredBstAuIdread-writecurrentDefine the base ID for the BST/AU - configured value.
1.3.6.1.4.1.12394.1.2.7.2.10.1.1.12ColumnrbSuCurrentBstAuMaskread-onlycurrentThe ID mask that together with the BST/AU ID defines a range of BST/AUs - current value.
1.3.6.1.4.1.12394.1.2.7.2.10.1.1.13ColumnrbSuConfiguredBstAuMaskread-writecurrentThe ID mask that together with the BST/AU ID defines a range of BST/AUs - configured value.
1.3.6.1.4.1.12394.1.2.7.2.10.2TablerbSuBestBstAuDataTablenot-accessiblecurrentThis table provides parameters information regarding the Best BST/AU Scanning Results. Includes parameters for all relevant AUs that were found in the scanning…
1.3.6.1.4.1.12394.1.2.7.2.10.2.1RowrbSuBestBstAuDataEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.7.2.10.2.1.1ColumnrbBstAuIndxread-onlycurrentThe table index
1.3.6.1.4.1.12394.1.2.7.2.10.2.1.2ColumnrbBstAuIdread-onlycurrentThe BST/AU ID.
1.3.6.1.4.1.12394.1.2.7.2.10.2.1.3ColumnrbBstAuRxFrequencyread-onlycurrentThe BST/AU's downlink frequency.
1.3.6.1.4.1.12394.1.2.7.2.10.2.1.4ColumnrbBstAuSNRread-onlycurrentThe SNR of the signal that was received at the SU side.
1.3.6.1.4.1.12394.1.2.7.2.10.2.1.5ColumnrbBstAuRxAntennaNumberread-onlycurrentThe Rx Antenna Number.
1.3.6.1.4.1.12394.1.2.7.2.11NoderbSuRadioParameters
1.3.6.1.4.1.12394.1.2.7.2.11.1TablerbSuRadioParametersTablenot-accessiblecurrentThis table provides parameters information regarding the Best BST/AU Frequency Scanning Parameters.
1.3.6.1.4.1.12394.1.2.7.2.11.1.1RowrbSuRadioParametersEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.7.2.11.1.1.1ColumnrbSuCurrentScanStartFreqread-onlycurrentFirst frequency to be used by the scanning process - current value.
1.3.6.1.4.1.12394.1.2.7.2.11.1.1.2ColumnrbSuConfiguredScanStartFreqread-writecurrentFirst frequency to be used by the scanning process - configured value.
1.3.6.1.4.1.12394.1.2.7.2.11.1.1.3ColumnrbSuCurrentScanEndFreqread-onlycurrentEnd frequency to be used by the scanning process - current value.
1.3.6.1.4.1.12394.1.2.7.2.11.1.1.4ColumnrbSuConfiguredScanEndFreqread-writecurrentEnd frequency to be used by the scanning process - configured value.
1.3.6.1.4.1.12394.1.2.7.2.11.1.1.5ColumnrbSuCurrentScanStepread-onlycurrentThe scanning step in MHz- current value.
1.3.6.1.4.1.12394.1.2.7.2.11.1.1.6ColumnrbSuConfiguredScanStepread-writecurrentThe scanning step in MHz- configured value. Resolution: 125 KHz step up to 1.75MHz for bandwith multiple of 1.75 and up to 5MHz for bandwith multiple of 2.5. D…
1.3.6.1.4.1.12394.1.2.7.2.11.1.1.7ColumnrbSuCurrentScanMaskread-onlycurrentThis is a bit-mask field: 00-FF. Allow scanning none standard frequencies that cannot be found by original Scan Steps - current value.
1.3.6.1.4.1.12394.1.2.7.2.11.1.1.8ColumnrbSuConfiguredScanMaskread-writecurrentThis is a bit-mask field: 00-FF. Allow scanning none standard frequencies that cannot be found by original Scan Steps - configured value. Bit 0: Steps of 0 MHz…
1.3.6.1.4.1.12394.1.2.7.2.11.1.1.9ColumnrbSuDiscreteF1read-onlycurrentSu Discrete 1st Frequency. 0(Null) means frequency is not configured.
1.3.6.1.4.1.12394.1.2.7.2.11.1.1.10ColumnrbSuDiscreteF2read-onlycurrentSu Discrete 2nd Frequency. 0(Null) means frequency is not configured.
1.3.6.1.4.1.12394.1.2.7.2.11.1.1.11ColumnrbSuDiscreteF3read-onlycurrentSu Discrete 3rd Frequency. 0(Null) means frequency is not configured.
1.3.6.1.4.1.12394.1.2.7.2.11.1.1.12ColumnrbSuDiscreteF4read-onlycurrentSu Discrete 4th Frequency. 0(Null) means frequency is not configured.
1.3.6.1.4.1.12394.1.2.7.2.11.1.1.13ColumnrbSuDiscreteF5read-onlycurrentSu Discrete 5th Frequency. 0(Null) means frequency is not configured.
1.3.6.1.4.1.12394.1.2.7.2.11.1.1.14ColumnrbSuDiscreteF6read-onlycurrentSu Discrete 6th Frequency. 0(Null) means frequency is not configured.
1.3.6.1.4.1.12394.1.2.7.2.11.1.1.15ColumnrbSuDiscreteF7read-onlycurrentSu Discrete 7th Frequency. 0(Null) means frequency is not configured.
1.3.6.1.4.1.12394.1.2.7.2.11.1.1.16ColumnrbSuDiscreteF8read-onlycurrentSu Discrete 8th Frequency. 0(Null) means frequency is not configured.
1.3.6.1.4.1.12394.1.2.7.2.11.1.1.17ColumnrbSuDiscreteF9read-onlycurrentSu Discrete 9th Frequency. 0(Null) means frequency is not configured.
1.3.6.1.4.1.12394.1.2.7.2.11.1.1.18ColumnrbSuDiscreteF10read-onlycurrentSu Discrete 10th Frequency. 0(Null) means frequency is not configured.
1.3.6.1.4.1.12394.1.2.7.2.11.1.1.19ColumnrbSuCurrentBandwidthread-onlycurrentb175 (1): 1.75 MHz b35 (2): 3.5 MHz b50 (3): 5 MHz b70 (4): 7 MHz b100 (5): 10 MHz The actually available bandwidths depend on the SU's hardware and SW version…
1.3.6.1.4.1.12394.1.2.7.2.11.1.1.20ColumnrbSuConfiguredBandwidthread-writecurrentThis parameter defines the configured bandwidth, that will be in effect after the next reset.
1.3.6.1.4.1.12394.1.2.8NoderbTesting
1.3.6.1.4.1.12394.1.2.8.1NoderbBerTest
1.3.6.1.4.1.12394.1.2.8.1.1NoderbBerTestSetup
1.3.6.1.4.1.12394.1.2.8.1.1.1ScalarrbBerTestDataSizeread-writecurrentNot supported in current version. The total number of BER test bytes to be transmitted. When starting a BER test, this parameter must be sent in together with …
1.3.6.1.4.1.12394.1.2.8.1.1.2ScalarrbBerTestModulationread-writecurrentNot supported in current version. Modulation and Forwarding Error Correction Rate to be used during the BER test. When starting a BER test, this parameter must…
1.3.6.1.4.1.12394.1.2.8.1.1.3ScalarrbBerTestActionread-writecurrentNot supported in current version. Initiating/terminating the test. When starting a BER test, rbBerTestAction start (1) must be sent in together with all other …
1.3.6.1.4.1.12394.1.2.8.1.1.4ScalarrbBerTestStatusread-onlycurrentNot supported in current version. The status of the test.
1.3.6.1.4.1.12394.1.2.8.1.1.5ScalarrbBerTestSUread-onlycurrentNot supported in current version. The MAC address of SU to be tested during the BER test.
1.3.6.1.4.1.12394.1.2.8.1.1.6ScalarrbBerTestTrafficPriorityread-writecurrentNot supported in current version. The service priority of the BER test traffic. When starting a BER test, this parameter must be sent in together with all othe…
1.3.6.1.4.1.12394.1.2.8.1.1.7ScalarrbBerTestMaxPacketSizeread-writecurrentNot supported in current version. The packet size in bytes. When starting a BER test, this parameter must be sent in together with all other test parameters, a…
1.3.6.1.4.1.12394.1.2.8.1.2NoderbBerTestResults
1.3.6.1.4.1.12394.1.2.8.1.2.1ScalarrbBerTestULReceivedBitsread-onlycurrentNot supported in current version. Number of bits received during the last BER test in the UpLink direction.
1.3.6.1.4.1.12394.1.2.8.1.2.2ScalarrbBerTestULReceivedErrorBitsread-onlycurrentNot supported in current version. Number of error bits received during the last BER test in the UpLink direction.
1.3.6.1.4.1.12394.1.2.8.1.2.3ScalarrbBerTestDLReceivedBitsread-onlycurrentNot supported in current version. Number of bits received during the last BER test in the DownLink direction.
1.3.6.1.4.1.12394.1.2.8.1.2.4ScalarrbBerTestDLReceivedErrorBitsread-onlycurrentNot supported in current version. Number of error bits received in the DownLink direction during the last BER test.
1.3.6.1.4.1.12394.1.2.8.1.2.5ScalarrbBerTestDLMapLostread-onlycurrentNot supported in current version. Number of times MAP was lost during the last BER test in the DownLink direction.
1.3.6.1.4.1.12394.1.2.8.1.2.6ScalarrbBerTestResultsSUread-onlycurrentNot supported in current version. The MAC address of the SU.
1.3.6.1.4.1.12394.1.2.8.1.2.7ScalarrbBerTestUplinkBERread-onlycurrentNot supported in current version. The BER in the Uplink Direction.
1.3.6.1.4.1.12394.1.2.8.1.2.8ScalarrbBerTestDownlinkBERread-onlycurrentNot supported in current version. The BER in the Downlink Direction.
1.3.6.1.4.1.12394.1.2.9NoderbIPConfig
1.3.6.1.4.1.12394.1.2.9.1TablerbIpIfConfigTablenot-accessiblecurrentThis table contains IP configuration parameters per interface.
1.3.6.1.4.1.12394.1.2.9.1.1RowrbIpIfConfigEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.9.1.1.1ColumnipIfConfigIfIndexread-onlycurrentIndex of Ethernet Interface. In NPU and Micro Base Station, 1 is for the DATA port and 2 is for the MGMT port. In SU, 1 is for the ETHERNET port and 2 is not a…
1.3.6.1.4.1.12394.1.2.9.1.1.2ColumnipIfConfigVlanIdread-writecurrentThe management VLAN ID associated with the specific interface. Applicable only for the DATA port of NPU/Micro Base Station. The range is from 0 to 4095, where …
1.3.6.1.4.1.12394.1.2.9.1.1.3ColumnipIfConfigIpAddressread-writecurrentIP Address of the interface.
1.3.6.1.4.1.12394.1.2.9.1.1.4ColumnipIfConfigNetworkMaskread-writecurrentThe Subnet Mask of the interface.
1.3.6.1.4.1.12394.1.2.9.1.1.5ColumnipIfConfigDefaultGatewayread-writecurrentDefault Gateway IP Address of the interface.
1.3.6.1.4.1.12394.1.2.9.1.1.6ColumnipIfStaticRouteSubnetread-writecurrentApplicable only to the MGMT port of NPU/Micro Base Station. The Destination Subnet (base IP address of the subnet) of the stations that can manage the device w…
1.3.6.1.4.1.12394.1.2.9.1.1.7ColumnipIfStaticRouteSubnetMaskread-writecurrentApplicable only to the MGMT port of NPU/Micro Base Station. The Destination Subnet Mask associated with the Destination Subnet (ipIfStaticRouteSubnet).
1.3.6.1.4.1.12394.1.2.10NoderbSwUpgrade
1.3.6.1.4.1.12394.1.2.10.1ScalarrbSwAuFilesread-onlycurrentString that contains the names of AU software files in the NPU (up to 4), separated by ;
1.3.6.1.4.1.12394.1.2.10.2ScalarrbSwSuFilesread-onlycurrentString that contains names of SU software files in NPU/Micro Base Station (up to 4), separated by ;
1.3.6.1.4.1.12394.1.2.10.3ScalarrbSwDeleteFilesread-writecurrentString that contains names, separated by ;, of the AU/SU software files to deleted.
1.3.6.1.4.1.12394.1.2.10.4ScalarrbSwSuDefaultFileread-writecurrentIn SUs using SW version below 2.5: The name of the software file that should be used by Temporary SU upon the Network Entry. In SUs using SW version 2.5 and hi…
1.3.6.1.4.1.12394.1.2.10.5ScalarrbSwSuDefaultActionread-writecurrentIn SUs using SW version below 2.5: The Action that should be performed by Temporary SU upon the Network Entry. Action should be performed using the rbSwSuDefau…
1.3.6.1.4.1.12394.1.2.10.6TablerbSwUpgradeLogTablenot-accessiblecurrentThis table contains the status of the last software upgrade performed for specific AUs or SUs.
1.3.6.1.4.1.12394.1.2.10.6.1RowrbSwUpgradeLogEntrynot-accessiblecurrentTable entry
1.3.6.1.4.1.12394.1.2.10.6.1.1ColumnrbSwDeviceTyperead-onlycurrentType of device participating in the software upgrade process.
1.3.6.1.4.1.12394.1.2.10.6.1.2ColumnrbSwDeviceIdread-onlycurrentIdentification of device. For AU - slot number , for SU - MAC Address.
1.3.6.1.4.1.12394.1.2.10.6.1.3ColumnrbSwUpgradeFileNameread-onlycurrentThe name of the software file that was used for upgrade.
1.3.6.1.4.1.12394.1.2.10.6.1.4ColumnrbSwUpgradeActionread-onlycurrentThe last performed software upgrade action.
1.3.6.1.4.1.12394.1.2.10.6.1.5ColumnrbSwUpgradeStartTimeread-onlycurrentThe time when the software upgrade process was started. Not supported in current version.
1.3.6.1.4.1.12394.1.2.10.6.1.6ColumnrbSwUpgradeEndTimeread-onlycurrentThe time when the software upgrade process was finished. Not supported in current version.
1.3.6.1.4.1.12394.1.2.10.6.1.7ColumnrbSwUpgradeStatusread-onlycurrentThe status of the software upgrade process.
1.3.6.1.4.1.12394.1.2.10.7ScalarrbSwSuSiDefaultFileread-writecurrentThe SW file that should be used upon network entry by all SUs using Air Interface type si. Not applicable if either rbAuSuUpgradeSwFileName in the AU serving t…
1.3.6.1.4.1.12394.1.2.10.8ScalarrbSwSuSiDefaultActionread-writecurrentThe action to be taken with the rbSwSuSiDefaultFile upon network entry by all SUs using Air Interface type si. Not applicable if either the rbAuSuUpgradeSwActi…
1.3.6.1.4.1.12394.1.2.10.9ScalarrbSwAuDefaultFileread-writecurrentThe name of the software file that should be used by an AU using Air Interface type a upon the Network Entry. Not applicable if rbAuUpgradeSwFileName for the A…
1.3.6.1.4.1.12394.1.2.10.10ScalarrbSwAuDefaultActionread-writecurrentThe Action that should be performed by an AU using Air Interface type a upon the Network Entry. Action should be performed using the rbSwAuDefaultFile. Not app…
1.3.6.1.4.1.12394.1.2.10.11ScalarrbSwAuSiDefaultFileread-writecurrentThe name of the software file that should be used by an AU using Air Interface type si upon the Network Entry. Not applicable if rbAuUpgradeSwFileName for the …
1.3.6.1.4.1.12394.1.2.10.12ScalarrbSwAuSiDefaultActionread-writecurrentThe Action that should be performed by an AU using Air Interface type si upon the Network Entry. Action should be performed using the rbSwAuSiDefaultFile. Not …
1.3.6.1.4.1.12394.1.2.10.13ScalarrbBstClearAllSuSwUpgradeParamsread-writecurrentClears the SW Upgrade parameters for all SUs served by the Base Station: For all SUs, rbSuUpgradeSwFileName will be set to an empty string, and rbSuUnitControl…
1.3.6.1.4.1.12394.1.2.10.14ScalarrbBstClearAllAuSwUpgradeParamsread-writecurrentClears the SW Upgrade parameters for all AUs in the Base Station: For all AUs, rbAuUpgradeSwFileName will be set to an empty string, and rbAuUnitControl will b…
1.3.6.1.4.1.12394.1.2.11NoderbBaseStation
1.3.6.1.4.1.12394.1.2.11.1NoderbBsAtpcParameters
1.3.6.1.4.1.12394.1.2.11.1.1ScalarrbBsATPCSupportread-writecurrentThis parameter defines if ATPC mechanism is supported by the Base Station.
1.3.6.1.4.1.12394.1.2.11.1.2ScalarrbBsOptimalRSSIread-writecurrentThe RSSI in dBm required from all SUs when ATPC is enabled.
1.3.6.1.4.1.12394.1.2.11.2NoderbBsCellParameters
1.3.6.1.4.1.12394.1.2.11.2.1ScalarrbBSConfiguredOperatorIdread-writecurrentOperator ID.
1.3.6.1.4.1.12394.1.2.11.2.2ScalarrbBSConfiguredCellIdread-writecurrentUnique Cell ID.
1.3.6.1.4.1.12394.1.2.11.3NoderbBsRFModeParameters
1.3.6.1.4.1.12394.1.2.11.3.1ScalarrbBsRFConfiguredDuplexModeread-writecurrentConfigured Duplex Mode.
1.3.6.1.4.1.12394.1.2.11.3.2ScalarrbBsRFCurrentDuplexModeread-onlycurrentCurrent Duplex Mode.
1.3.6.1.4.1.12394.1.2.11.3.3ScalarrbBsRFConfiguredDlUlRatioread-writecurrentDL-UL Ratio configurable only for TDD mode, for FDD will be always unavailable (0). For TDD mode the following values can be selected: 65-35% (1), 60-40% (2), …
1.3.6.1.4.1.12394.1.2.11.3.4ScalarrbBsRFCurrentDlUlRatioread-onlycurrentCurrent DL-UL Ratio.
1.3.6.1.4.1.12394.1.2.11.4NoderbBSClockConfigParameters
1.3.6.1.4.1.12394.1.2.11.4.1ScalarrbBSConfiguredExternalPPSClockread-writecurrentConfigured option of the External 1PPS Clock parameter.
1.3.6.1.4.1.12394.1.2.11.4.2ScalarrbBSCurrentExternalPPSClockread-onlycurrentCurrent option of the External 1PPS Clock parameter.
1.3.6.1.4.1.12394.1.2.11.4.3ScalarrbBSConfiguredExternal16MhzClockread-writecurrentConfigured option of the External 16MHz Clock parameter.
1.3.6.1.4.1.12394.1.2.11.4.4ScalarrbBSCurrentExternal16MhzClockread-onlycurrentCurrent option of the External 16MHz Clock parameter.
1.3.6.1.4.1.12394.1.2.12NoderbRadioCluster
1.3.6.1.4.1.12394.1.2.12.1TablerbRadioClusterTablenot-accessiblecurrentTable that holds Radio Clusters` parameters.
1.3.6.1.4.1.12394.1.2.12.1.1RowrbRadioClusterEntrynot-accessiblecurrentRow Description
1.3.6.1.4.1.12394.1.2.12.1.1.1ColumnrbRadioClusterIdread-onlycurrentRadio Cluster ID.
1.3.6.1.4.1.12394.1.2.12.1.1.2ColumnrbRadioClusterNameread-writecurrentRadio Cluster name.
1.3.6.1.4.1.12394.1.2.12.1.1.3ColumnrbRadioClusterLocationread-writecurrentRadio Cluster Location.
1.3.6.1.4.1.12394.1.2.12.1.1.4ColumnrbRadioClusterSectorHeadingread-writecurrentRadio Cluster Sector Heading - the angle from the north.
1.3.6.1.4.1.12394.1.2.12.1.1.5ColumnrbRadioClusterSectorBeamWidthread-writecurrentRadio Cluster Sector Antenna`s Beam Width.
1.3.6.1.4.1.12394.1.2.12.1.1.6ColumnrbRadioClusterRowStatusread-writecurrentControl for creating and deleting entries. Entries may be modified while active. active (1) - means that the entry is available for use by the managed device a…
1.3.6.1.4.1.12394.1.2.13NoderbOduConfig
1.3.6.1.4.1.12394.1.2.13.1TablerbOduConfigTablenot-accessiblecurrentTable that holds ODU`s parameters.
1.3.6.1.4.1.12394.1.2.13.1.1RowrbOduConfigEntrynot-accessiblecurrentRow Description
1.3.6.1.4.1.12394.1.2.13.1.1.1ColumnrbOduConfigIdread-onlycurrentODU's ID.
1.3.6.1.4.1.12394.1.2.13.1.1.2ColumnrbOduAssociatedRadioClusterIdread-writecurrentAssociated Radio Cluster ID. Valid values: 1 to 6. Must be the ID of a defined Radio Cluster. Agent will return 0 if Associated Radio Cluster ID is unknown.
1.3.6.1.4.1.12394.1.2.13.1.1.3ColumnrbOduTxPowerread-writecurrentThe ODU's Tx Power in dBm. Allowed range is from 13 to 50, using a resolution of 0.25dBm. Actual range is from 13 to the value defined by rbOduMaxTxPower. For …
1.3.6.1.4.1.12394.1.2.13.1.1.4ColumnrbOduAdminStatusread-writecurrentOdu Admin Status.
1.3.6.1.4.1.12394.1.2.13.1.1.5ColumnrbOduTemperatureread-onlycurrentOdu Messured Temperature. Agent will return 0 if Odu Temperature is unknown.
1.3.6.1.4.1.12394.1.2.13.1.1.6ColumnrbOduHwRevisionread-onlycurrentOdu HW Revision.
1.3.6.1.4.1.12394.1.2.13.1.1.7ColumnrbOduHwConfigDescriptionread-onlycurrentOdu HW Configuration Description.
1.3.6.1.4.1.12394.1.2.13.1.1.8ColumnrbOduOperationalStatusread-onlycurrentOdu Operational Status.
1.3.6.1.4.1.12394.1.2.13.1.1.9ColumnrbOduHwHC08Versionread-onlycurrentThe version of the HC08 component in the ODU.
1.3.6.1.4.1.12394.1.2.13.1.1.10ColumnrbOduCpldVersionread-onlycurrentThe version of the CPLD component in the ODU.
1.3.6.1.4.1.12394.1.2.13.1.1.11ColumnrbOduCardSerialNumberread-onlycurrentThe serial number of the ODU.
1.3.6.1.4.1.12394.1.2.13.1.1.12ColumnrbOduConfigFrequencyBandread-writecurrentOdu Configured Frequency Band ID. Must be one of the Frequency Band IDs available in the Frequency Bands Table. Agent will return 0 if Frequency Band is unknow…
1.3.6.1.4.1.12394.1.2.13.1.1.13ColumnrbOduRowStatusread-writecurrentControl for creating and deleting entries. Entries may be modified while active. active (1) - means that the entry is available for use by the managed device a…
1.3.6.1.4.1.12394.1.2.13.1.1.14ColumnrbOduMaxTxPowerread-onlycurrentThe maximum Tx power supported by the ODU, in dBm units.
1.3.6.1.4.1.12394.1.2.14NoderbChainConfig
1.3.6.1.4.1.12394.1.2.14.1ScalarrbGPSSupportedread-onlycurrentThe GPS support status.
1.3.6.1.4.1.12394.1.2.14.2ScalarrbConfiguredChainNumberread-writecurrentThe Configured GPS Chain number. Allowed range is from 1 to 1500. 0 is only init value that need to be modified in order to have possibility to change other ch…
1.3.6.1.4.1.12394.1.2.14.3ScalarrbCurrentChainNumberread-onlycurrentThe Current GPS Chain number.
1.3.6.1.4.1.12394.1.2.14.4ScalarrbGPSConfiguredTyperead-writecurrentThe Configured GPS Protocol.
1.3.6.1.4.1.12394.1.2.14.5ScalarrbGPSCurrentTyperead-onlycurrentThe Current GPS Protocol.
1.3.6.1.4.1.12394.1.2.14.6ScalarrbTimeZoneOffsetFromUTCread-writecurrentLocal Time Zone offset from UTC. The range is -12:00 up to +13:00 in 30 minutes resolution.
1.3.6.1.4.1.12394.1.2.14.7ScalarrbStopTxAfterHoldOverTimeoutread-writecurrentDefines whether to stop transmitting after Hold Over Timeout. Disable means not to stop transmissions. Enable means stop transmissions after Timeout.
1.3.6.1.4.1.12394.1.2.14.8ScalarrbHoldOverPassedTimeoutread-writecurrentHold Over Timeout in minutes. AUs will enter Hold Over mode when receiving less than two satellites.
1.3.6.1.4.1.12394.1.2.15NoderbGPSInfo
1.3.6.1.4.1.12394.1.2.15.1ScalarrbGPSNumberOfRxSatellitesread-onlycurrentNumber of received satellites.
1.3.6.1.4.1.12394.1.2.15.2ScalarrbGPSLongituderead-onlycurrentGPS Longitude. Format is llll.lll,a: llll.lll is longitude in degrees; a - is E(east) or W(west).
1.3.6.1.4.1.12394.1.2.15.3ScalarrbGPSLatituderead-onlycurrentGPS Latitude. Format is llll.lll,a: llll.lll is latitude in degrees; a - is N(North) or S(South).
1.3.6.1.4.1.12394.1.2.15.4ScalarrbGPSAltituderead-onlycurrentGPS Antenna Altitude in meters. Format is a.a,M: a.a is altitude; M - is Meters.
1.3.6.1.4.1.12394.1.2.15.5ScalarrbGPSLocalDateAndTimeread-onlycurrentCalculated local Date and time. The format is hh:mm:ss, dd/mm/yyyy. For example: 23:22:04, 25/12/2006.
1.3.6.1.4.1.12394.1.2.15.6ScalarrbGPSNavigationProcessorSWVersionread-onlycurrentNavigation Processor SW version. Format is Major Version Number, Minor Version Number, Month, Day and Year+1900.
1.3.6.1.4.1.12394.1.2.15.7ScalarrbGPSSignalProcessorSWVersionread-onlycurrentSignal Processor SW version. Format is Major Version Number, Minor Version Number, Month, Day and Year+1900.
1.3.6.1.4.1.12394.1.2.50NoderbLicense
1.3.6.1.4.1.12394.1.2.50.1TablerbLicenseBankTablenot-accessiblecurrentA Table of CPE Licenses.
1.3.6.1.4.1.12394.1.2.50.1.1RowrbLicenseBankEntrynot-accessiblecurrentTable entry.
1.3.6.1.4.1.12394.1.2.50.1.1.1ColumnrbLicenseIdread-onlycurrentType of Licenses: bandwidth (1) - Bandwidth License.
1.3.6.1.4.1.12394.1.2.50.1.1.2ColumnrbLicenseValueread-onlycurrentFor Bandwidth Limitation License the current valid value is 0 for Unlimited Bandwidth.
1.3.6.1.4.1.12394.1.2.50.1.1.3ColumnrbLicenseCountread-onlycurrentThe number of applicable Licenses that are available in the CPEs License Bank.
1.3.6.1.4.1.12394.1.2.50.1.1.4ColumnrbLicenseDescriptionread-onlycurrentThe Licenses Description.
1.3.6.1.4.1.12394.1.2.50.2NoderbLicenseBst
1.3.6.1.4.1.12394.1.2.50.2.1TablerbLicenseBstTablenot-accessiblecurrentA Table of Base Station/Micro Base Station Licenses.
1.3.6.1.4.1.12394.1.2.50.2.1.1RowrbLicenseBstEntrynot-accessiblecurrentTable entry.
1.3.6.1.4.1.12394.1.2.50.2.1.1.1ColumnrbBstLicenseIdread-onlycurrentType of Licenses: bandwidth (1) - Bandwidth limitation for all PRO-L SUs served by the Base Station/Micro Base Station, maxNumberOfSUs (2) - Maximum Number of …
1.3.6.1.4.1.12394.1.2.50.2.1.1.2ColumnrbBstLicenseValueread-onlycurrentFor Bandwidth Limitation License the current valid value is 0 for Unlimited Bandwidth. For Maximum Number of SUs License the valid values are 50, 150, 250.
1.3.6.1.4.1.12394.1.2.50.2.1.1.3ColumnrbBstLicenseDescriptionread-onlycurrentThe Licenses Description.
1.3.6.1.4.1.12394.1.2.50.2.2ScalarrbNumberOfSUsGraceEndDateread-onlycurrentApplicable only to a Micro Base Station that was upgraded from SW version 2.0 or lower and does not have any Maximum Number of SUs License. The Grace Period wi…
1.3.6.1.4.1.12394.1.2.50.3TablerbSUTempGracePeriodLicenseTablenot-accessiblecurrentSU Temporary Grace Period License Table.
1.3.6.1.4.1.12394.1.2.50.3.1RowrbSUTempGracePeriodLicenseEntrynot-accessiblecurrentTable entry.
1.3.6.1.4.1.12394.1.2.50.3.1.1ColumnrbSUTempGracePeriodIndexread-onlycurrentThe INDEX of the SU Temporary Grace Period License Table.
1.3.6.1.4.1.12394.1.2.50.3.1.2ColumnrbSUTempGracePeriodSuMacAddrread-onlycurrentThe MAC address of the SU.
1.3.6.1.4.1.12394.1.2.50.3.1.3ColumnrbSUTempGracePeriodLicenseIdread-onlycurrentType of Licenses: bandwidth (1) - Bandwidth License.
1.3.6.1.4.1.12394.1.2.50.3.1.4ColumnrbSUTempGracePeriodLicenseEndDateread-onlycurrentSU Temporary Grace Period Date.
1.3.6.1.4.1.12394.1.2.50.4TablerbSUGracePeriodLicenseTablenot-accessiblecurrentSU Grace Period Table.
1.3.6.1.4.1.12394.1.2.50.4.1RowrbSUGracePeriodLicenseEntrynot-accessiblecurrentTable entry.
1.3.6.1.4.1.12394.1.2.50.4.1.1ColumnrbSUGracePeriodIndexread-onlycurrentThe INDEX of the SU Grace Period License Table.
1.3.6.1.4.1.12394.1.2.50.4.1.2ColumnrbSUGracePeriodSuMacAddrread-onlycurrentThe MAC address of the SU.
1.3.6.1.4.1.12394.1.2.50.4.1.3ColumnrbSUGracePeriodLicenseIdread-onlycurrentType of Licenses: bandwidth (1) - Bandwidth License.
1.3.6.1.4.1.12394.1.2.50.4.1.4ColumnrbSUGracePeriodLicenseEndDateread-onlycurrentSU Grace Period End Date.
1.3.6.1.4.1.12394.1.2.50.4.1.5ColumnrbSUGracePeriodLicenseStatusread-onlycurrentLicense SU Grace Period Admin Status.
1.3.6.1.4.1.12394.1.2.300ScalarendOfMibread-onlycurrentThis leaf is intended to solve getNext problem when the end of the MIB is reached.
Type Definitions
NameSyntaxStatusDescription
LinkSpeedAndDuplexINTEGER { unknown ( 1 ), fullDuplex100Mbps ( 2 ), halfDuplex100Mbps ( 3 ), fullDuplex10Mbps ( 4 ), halfDuplex10Mbps ( 5 ), fullDuplex1Gbps ( 6 ), halfDuplex1Gbps ( 7 ) }currentDescription.
ModulationINTEGER { notDefined (0), rBpsk12 (1), rBpsk34 (2), rQpsk12 (3), rQpsk34 (4), r16Qam12 (5), r16Qam34 (6), r64Qam23 (7), r64Qam34 (8) }currentDescription.
TenthdBInteger32currentThis data type represents power levels that are normally expressed in dB. Units are in tenths of a dB; for example, 5.1 dB will be represented as 51.
TrapSeverityINTEGER { none (0), critical (1), major (2), minor (3), warning (4), info (5) }currentDescription.
MIB Viewer