RBN-CES-MIB
78 objects
This MIB describes objects used for managing Circuit Emulation Service(CES) protocols, including RFC 5086: Structure-Aware Time Division Multiplexed (TDM) Circuit Emulation Service over Packet Switched Network (CESoPSN) and RFC 4553: Structure Agnostic Circuit Emulation Service over Packet Switch Network(SAToP).
Imported Objects
| IF-MIB | InterfaceIndex |
| RBN-ALARM-TC | RbnAlarmId |
| RBN-SMI | rbnMgmt |
| RBN-TC | RbnPercentage |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter64 Gauge32 Integer32 MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DateAndTime RowStatus TimeInterval TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2352.2.56 | IdentityrbnCesMIB | This MIB describes objects used for managing Circuit Emulation Service(CES) protocols, including RFC 5086: Structure-Aware Time Division Multiplexed (TDM) Circ… | ||
| 1.3.6.1.4.1.2352.2.56.1 | NoderbnCesMIBObjects | |||
| 1.3.6.1.4.1.2352.2.56.1.1 | ScalarrbnCesSlaInfoResetAll | read-write | current | Setting this object to 'true' resets all CES Service Level Agreement(SLA) information objects in the rbnCesSlaInfoTable. This object always returns 'false' val… |
| 1.3.6.1.4.1.2352.2.56.1.2 | TablerbnCesCfgTable | not-accessible | current | Configuration table for CES circuits. |
| 1.3.6.1.4.1.2352.2.56.1.2.1 | RowrbnCesCfgEntry | not-accessible | current | Each entry in this table represents a CES circuit. |
| 1.3.6.1.4.1.2352.2.56.1.2.1.1 | ColumnrbnCesCfgIndex | not-accessible | current | This object is used to uniquely identify a CES circuit. The value of this object should be the same as the value of ifIndex when they are used to identify the … |
| 1.3.6.1.4.1.2352.2.56.1.2.1.2 | ColumnrbnCesCfgPktLatency | read-create | current | This object specifies the time of packetizing frames into a packet. The packet latency is calculated by multiplying number of frames by a constant frame packet… |
| 1.3.6.1.4.1.2352.2.56.1.2.1.3 | ColumnrbnCesCfgJtrBfrDepth | read-create | current | The number of microseconds of expected packet delay variation for this CES PW over PSN. The value must be at least two times the expected packet jitter through… |
| 1.3.6.1.4.1.2352.2.56.1.2.1.4 | ColumnrbnCesCfgConsecPktsInSync | read-create | current | The number of consecutive packets that are required to exit loss of packet state(LOPS) |
| 1.3.6.1.4.1.2352.2.56.1.2.1.5 | ColumnrbnCesCfgConsecMissPktsOutSync | read-create | current | The number of consecutive missing packets that are required to enter loss of packet state(LOPS) |
| 1.3.6.1.4.1.2352.2.56.1.2.1.6 | ColumnrbnCesCfgIdlePattern | read-create | current | The object determines the value to be used on the TDM channel when packets have over/underflow in the jitter buffer or are missing for any reason at the CES bo… |
| 1.3.6.1.4.1.2352.2.56.1.2.1.7 | ColumnrbnCesCfgTrunkCtl | read-create | current | This object enforces the RFC 5086 requirement that controls at most one CES PW state(AIS or RDI) on the outgoing T1/E1 trunk. |
| 1.3.6.1.4.1.2352.2.56.1.2.1.8 | ColumnrbnCesCfgAdminStatus | read-create | current | This object controls CES feature on the circuit. Setting this object to 'up' enables CES on the circuit; setting this object to 'down' disables CES on the circ… |
| 1.3.6.1.4.1.2352.2.56.1.2.1.9 | ColumnrbnCesCfgRowStatus | read-create | current | This object is used to manage the creation and deletion of CES configuration conceptual rows. Except 'rbnCesCfgAdminStatus', 'read-create' objects in the conce… |
| 1.3.6.1.4.1.2352.2.56.1.3 | TablerbnCesStatsTable | not-accessible | current | CES statistics table. |
| 1.3.6.1.4.1.2352.2.56.1.3.1 | RowrbnCesStatsEntry | not-accessible | current | Each entry in this table represents a CES circuit. |
| 1.3.6.1.4.1.2352.2.56.1.3.1.1 | ColumnrbnCesStatsEgressOutOfBfrDroppedPkts | read-only | current | Number of packets dropped due to buffer starvation in the PSN to TDM direction(egress). |
| 1.3.6.1.4.1.2352.2.56.1.3.1.2 | ColumnrbnCesStatsEgressMissingPkts | read-only | current | Number of missing packets detected via control word sequence number gaps in the PSN to TDM direction(egress). |
| 1.3.6.1.4.1.2352.2.56.1.3.1.3 | ColumnrbnCesStatsEgressMalformedPkts | read-only | current | Number of malformed packets including unexpected size in the PSN to TDM direction(egress). |
| 1.3.6.1.4.1.2352.2.56.1.3.1.4 | ColumnrbnCesStatsEgressJtrBfrOverrunPkts | read-only | current | Number of packets dropped due to jitter buffer overrun in the PSN to TDM direction(egress). |
| 1.3.6.1.4.1.2352.2.56.1.3.1.5 | ColumnrbnCesStatsEgressJtrBfrUnderruns | read-only | current | Number of times jitter buffer underrun has been detected in the PSN to TDM direction(egress). |
| 1.3.6.1.4.1.2352.2.56.1.3.1.6 | ColumnrbnCesStatsEgressMisOrderPkts | read-only | current | Number of out of sequence packets received in the PSN to TDM direction(egress). |
| 1.3.6.1.4.1.2352.2.56.1.3.1.7 | ColumnrbnCesStatsEgressRemoteLossPkts | read-only | current | Number of packets received with the R bit set in the PSN to TDM direction(egress). |
| 1.3.6.1.4.1.2352.2.56.1.3.1.8 | ColumnrbnCesStatsEgressWindowSwitchovers | read-only | current | Number of times serial number lost synchronization and was forced to move to a new window in the PSN to TDM direction(egress). |
| 1.3.6.1.4.1.2352.2.56.1.3.1.9 | ColumnrbnCesStatsEgressRemoteAcDownPkts | read-only | current | Number of packets received with L bit set to 1, indicating that the far end's attachment circuit is down (in LOF or LOS or AIS) in the PSN to TDM direction(egr… |
| 1.3.6.1.4.1.2352.2.56.1.3.1.10 | ColumnrbnCesStatsEgressDuplicatePkts | read-only | current | Number of packets dropped due to being duplicated, as determined by the PW codeword sequence number in the PSN to TDM direction(egress). |
| 1.3.6.1.4.1.2352.2.56.1.3.1.11 | ColumnrbnCesStatsEgressDeniedPkts | read-only | current | Number of packets dropped because they are denied in the PSN to TDM direction(egress). |
| 1.3.6.1.4.1.2352.2.56.1.3.1.12 | ColumnrbnCesStatsEgressErrorEvents | read-only | current | Number of times a packet is replaced with a dummy packet in the PSN to TDM direction(egress) because the system is in underrun mode or the packet was lost. |
| 1.3.6.1.4.1.2352.2.56.1.3.1.13 | ColumnrbnCesStatsEgressErrorDataBlocks | read-only | current | Block of data transmitted to the TDM attachment circuit and of a size defined in accordance with the [ITU-T G.826] rules for the corresponding TDM service that… |
| 1.3.6.1.4.1.2352.2.56.1.3.1.14 | ColumnrbnCesStatsIngressOutOfBfrDroppedPkts | read-only | current | Number of packets that could not be sent due to buffer starvation in the PSN to TDM direction(egress). |
| 1.3.6.1.4.1.2352.2.56.1.3.1.15 | ColumnrbnCesStatsIngressSizeViolationDroppedPkts | read-only | current | Number of packets not transmitted because their size is greater than the largest supported in the PSN to TDM direction(egress). |
| 1.3.6.1.4.1.2352.2.56.1.3.1.16 | ColumnrbnCesStatsIngressTransmitDroppedPkts | read-only | current | Number of packets not transmitted due to congestion in the transmit queue in the PSN to TDM direction(egress). |
| 1.3.6.1.4.1.2352.2.56.1.4 | TablerbnCesEplCfgTable | not-accessible | current | CES excessive packet loss configuration table. |
| 1.3.6.1.4.1.2352.2.56.1.4.1 | RowrbnCesEplCfgEntry | not-accessible | current | Each entry in this table represents a set of global CES excessive packet loss configuration. |
| 1.3.6.1.4.1.2352.2.56.1.4.1.1 | ColumnrbnCesEplCfgIndex | not-accessible | current | This object is used to uniquely identify a set of CES excessive packet loss configuration. |
| 1.3.6.1.4.1.2352.2.56.1.4.1.2 | ColumnrbnCesEplCfgThreshold | read-create | current | Threshold in percentage representing the upper limits of measurement for excessive packet loss. It is the ratio of (Total Lost Packets) / (Total Transmitted Pa… |
| 1.3.6.1.4.1.2352.2.56.1.4.1.3 | ColumnrbnCesEplCfgFaultDeclarationTime | read-create | current | This object controls fault declaration time of excessive packet loss alarm. It is a successive duration that experience excessive packet loss defect. |
| 1.3.6.1.4.1.2352.2.56.1.4.1.4 | ColumnrbnCesEplCfgClearingTime | read-create | current | This object controls how excessive packet loss alarms are cleared. It is a successive periods of duration T that do not experience an excessive packet loss def… |
| 1.3.6.1.4.1.2352.2.56.1.4.1.5 | ColumnrbnCesEplCfgStatsResetAll | read-write | current | Setting this object to 'true' resets all CES excessive packet loss statistic objects in the rbnCesEplStatsTable. This object always returns 'false' value. |
| 1.3.6.1.4.1.2352.2.56.1.4.1.6 | ColumnrbnCesEplCfgAdminStatus | read-create | current | This object controls the CES excessive packet loss configurations. Setting this object to 'up' enables CES excessive packet loss monitoring on all CES circuits… |
| 1.3.6.1.4.1.2352.2.56.1.4.1.7 | ColumnrbnCesEplCfgRowStatus | read-create | current | This object is used to manage the creation and deletion of CES excessive packet loss configuration conceptual rows. Except 'rbnCesEplCfgAdminStatus', 'read-cre… |
| 1.3.6.1.4.1.2352.2.56.1.5 | TablerbnCesEplStatsTable | not-accessible | current | CES excessive packet loss statistics table. |
| 1.3.6.1.4.1.2352.2.56.1.5.1 | RowrbnCesEplStatsEntry | not-accessible | current | Each entry in this table represents a CES circuit. |
| 1.3.6.1.4.1.2352.2.56.1.5.1.1 | ColumnrbnCesEplStatsIndex | not-accessible | current | This object is used to uniquely identify a CES circuit. The value of this object should be the same as the value of ifIndex when they are used to identify the … |
| 1.3.6.1.4.1.2352.2.56.1.5.1.2 | ColumnrbnCesEplStatsEntryTime | read-only | current | Date and time when the current excessive packet loss snapshot starts. |
| 1.3.6.1.4.1.2352.2.56.1.5.1.3 | ColumnrbnCesEplStatsEntryTotalPktLossTime | read-only | current | The entry total packet loss time of current excessive packet loss snapshot. |
| 1.3.6.1.4.1.2352.2.56.1.5.1.4 | ColumnrbnCesEplStatsExitTime | read-only | current | The exit packet loss time of current excessive packet loss snapshot. |
| 1.3.6.1.4.1.2352.2.56.1.5.1.5 | ColumnrbnCesEplStatsExitTotalPktLossTime | read-only | current | The exit total packet loss time of current excessive packet loss snapshot. |
| 1.3.6.1.4.1.2352.2.56.1.5.1.6 | ColumnrbnCesEplStatsCount | read-only | current | The total number of times when the CES PW was in the excessive packet loss state. |
| 1.3.6.1.4.1.2352.2.56.1.5.1.7 | ColumnrbnCesEplStatsTotalCircuitTime | read-only | current | Total CES PW time including CES PW up time and time spent in excessive packet loss state. |
| 1.3.6.1.4.1.2352.2.56.1.5.1.8 | ColumnrbnCesEplStatsTotalFailureRate | read-only | current | The percentage of time the CES PW spent in the excessive packet loss state during the total CES PW time. |
| 1.3.6.1.4.1.2352.2.56.1.5.1.9 | ColumnrbnCesEplStatsReset | read-write | current | This object is used to reset CES EPL statistic objects in the entry. Setting this object to 'true' resets 'rbnCesEplStatsEntryTime' to current time and other C… |
| 1.3.6.1.4.1.2352.2.56.1.6 | TablerbnCesSlaInfoTable | not-accessible | current | CES Service Level Agreement information table. |
| 1.3.6.1.4.1.2352.2.56.1.6.1 | RowrbnCesSlaInfoEntry | not-accessible | current | Each entry in this table represents a CES circuit that is in its outage state. |
| 1.3.6.1.4.1.2352.2.56.1.6.1.1 | ColumnrbnCesSlaInfoIndex | not-accessible | current | This object is used to uniquely identify a CES circuit. The value of this object should be the same as the value of ifIndex when they are used to identify the … |
| 1.3.6.1.4.1.2352.2.56.1.6.1.2 | ColumnrbnCesSlaInfoLatestOutageTime | read-only | current | The amount of time during the latest occurrence when the CES PW was in the packet loss or underrun state. |
| 1.3.6.1.4.1.2352.2.56.1.6.1.3 | ColumnrbnCesSlaInfoEntryLatestOutage | read-only | current | Date and time of the most recent occurrence when the CES PW entered the packet loss or underrun state. |
| 1.3.6.1.4.1.2352.2.56.1.6.1.4 | ColumnrbnCesSlaInfoExitLatestOutage | read-only | current | Date and time of the most recent occurrence when the CES PW exited the packet loss or underrun state. |
| 1.3.6.1.4.1.2352.2.56.1.6.1.5 | ColumnrbnCesSlaInfoLastOutageTime | read-only | current | The duration of the previous occurrence(the one before the latest occurrence) when the CES PW was in the packet loss or underrun state. |
| 1.3.6.1.4.1.2352.2.56.1.6.1.6 | ColumnrbnCesSlaInfoLastUpTime | read-only | current | Total CES PW up time before the latest outage occurred. |
| 1.3.6.1.4.1.2352.2.56.1.6.1.7 | ColumnrbnCesSlaInfoTotalOutageTime | read-only | current | Total outage time since the CES PW was created. |
| 1.3.6.1.4.1.2352.2.56.1.6.1.8 | ColumnrbnCesSlaInfoTotalUpTime | read-only | current | Total CES PW up time since it was created excluding the cumulative outage time. |
| 1.3.6.1.4.1.2352.2.56.1.6.1.9 | ColumnrbnCesSlaInfoOutageCount | read-only | current | Number of times a CES PW outage occurred. |
| 1.3.6.1.4.1.2352.2.56.1.6.1.10 | ColumnrbnCesSlaInfoReset | read-write | current | Setting this object to 'true' resets CES SLA objects to zero. The object always returns 'false' value. |
| 1.3.6.1.4.1.2352.2.56.1.7 | TablerbnCesCardAlarmTable | not-accessible | current | This table consists of CES specific card alarms. The alarms are used to indicate CES card level communication errors. Other card alarms are not included in the… |
| 1.3.6.1.4.1.2352.2.56.1.7.1 | RowrbnCesCardAlarmEntry | not-accessible | current | Each entry in this table represents a CES specific card alarm. |
| 1.3.6.1.4.1.2352.2.56.1.7.1.1 | ColumnrbnCesCardAlarmId | not-accessible | current | This object is used to uniquely identify a CES card alarm. |
| 1.3.6.1.4.1.2352.2.56.1.7.1.2 | ColumnrbnCesCardAlarmNotificationEnable | read-write | current | This object indicates whether rbnCardAlarm notification is generated. If true, a notification is generated for the card alarm indicated by rbnCesCardAlarmId. O… |
| 1.3.6.1.4.1.2352.2.56.2 | NoderbnCesMIBConformance | |||
| 1.3.6.1.4.1.2352.2.56.2.1 | NoderbnCesMIBCompliances | |||
| 1.3.6.1.4.1.2352.2.56.2.1.1 | CompliancerbnCesMIBCompliance | read-only | current | The compliance statement for CES MIB implementations. |
| 1.3.6.1.4.1.2352.2.56.2.2 | NoderbnCesMIBGroups | |||
| 1.3.6.1.4.1.2352.2.56.2.2.1 | GrouprbnCesCfgGroup | current | Conformance group for CES configurations. | |
| 1.3.6.1.4.1.2352.2.56.2.2.2 | GrouprbnCesStatsGroup | current | Conformance group for CES statistics. | |
| 1.3.6.1.4.1.2352.2.56.2.2.3 | GrouprbnCesEplCfgGroup | current | Conformance group for CES excessive packet loss configurations. | |
| 1.3.6.1.4.1.2352.2.56.2.2.4 | GrouprbnCesEplStatsGroup | current | Conformance group for CES excessive packet loss statistics. | |
| 1.3.6.1.4.1.2352.2.56.2.2.5 | GrouprbnCesSlaInfoGroup | current | Conformance group for CES service level agreement statistics. | |
| 1.3.6.1.4.1.2352.2.56.2.2.6 | GrouprbnCesCardAlarmGroup | current | Conformance group for CES card alarms. |