MIB Viewer

REDLINE-AN80I-IF-MIB

110 objects
This MIB module contains object definitions applicable only to Redline AN80i module.
Imported Objects
REDLINE-MIBredlineTransmission
SNMPv2-CONFMODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP
SNMPv2-SMICounter32 Counter64 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32
SNMPv2-TCDisplayString MacAddress RowStatus
OIDNameAccessStatusDescription
1.3.6.1.4.1.10728.2.10.2IdentityredlineAn80iIfMibThis MIB module contains object definitions applicable only to Redline AN80i module.
1.3.6.1.4.1.10728.2.10.2.0NoderedlineAn80iIfTrapDefinitions
1.3.6.1.4.1.10728.2.10.2.0.1Notificationan80iIfRegistrationFailedTrapcurrentEvent that reports the failure of a registration attempt of a SS that is not defined in the link table.
1.3.6.1.4.1.10728.2.10.2.0.2Notificationan80iIfRegistrationOKTrapcurrentAn event to report the successful SS registration.
1.3.6.1.4.1.10728.2.10.2.1NoderedlineAn80iIfPtpObjects
1.3.6.1.4.1.10728.2.10.2.1.1NoderedlineAn80iIfPtpLinkConfig
1.3.6.1.4.1.10728.2.10.2.1.1.1Scalaran80iIfEncryptionControlread-writecurrentSpecifies if encryption type.
1.3.6.1.4.1.10728.2.10.2.1.1.2Scalaran80iIfModReductionread-writecurrentApplies when the adaptive rate is disabled, and specifies how many levels the system must drop in modulation before beginning retransmission to address packet …
1.3.6.1.4.1.10728.2.10.2.1.1.3Scalaran80iIfAdaptiveModread-writecurrentIf enabled, the system automatically adjust the modulation to obtain the maximum throughput.
1.3.6.1.4.1.10728.2.10.2.1.1.4Scalaran80iIfUncodedBurstRateread-writecurrentThe maximum index of the link uncoded burst rate. The rate also depends on the channel width. The possible values are 0..7.
1.3.6.1.4.1.10728.2.10.2.1.1.5Scalaran80iIfEncryptionKeyread-writecurrentThe Encryption Key used for the AN-80i. Enter the MAC address of the peer equipment to enable over-the-air data encryption.
1.3.6.1.4.1.10728.2.10.2.1.1.6Scalaran80iIfPacketRetransControlread-writecurrentEnables/disables packet retransmission. The retransmission scheme is based on the Acknowledge /Request (ARQ) algorithm that detects when packets are lost and m…
1.3.6.1.4.1.10728.2.10.2.1.1.7Scalaran80iIfLinkLenModeread-writecurrentIn manual mode the system uses the user-supplied value for link length. In the auto mode the system calculate itself the distance, which can be read using 'cal…
1.3.6.1.4.1.10728.2.10.2.1.1.8Scalaran80iIfLinkLengthread-writecurrentUser supplied PTP Link Length [Km].
1.3.6.1.4.1.10728.2.10.2.1.1.9Scalaran80iIfCalcLinkDstread-onlycurrentThe calculated link distance [Km].
1.3.6.1.4.1.10728.2.10.2.1.1.10Scalaran80iIfLinkNameread-writecurrentLink Name.
1.3.6.1.4.1.10728.2.10.2.1.2NoderedlineAn80iIfPtpLinkStats
1.3.6.1.4.1.10728.2.10.2.1.2.1Scalaran80iIfCurrUncodedBurstRateread-onlycurrentIndicates the index of the link uncoded burst rate. With adaptive modulation enabled, this rate may change over time.
1.3.6.1.4.1.10728.2.10.2.1.2.2Scalaran80iIfPtpLinkStatusread-onlycurrentIndicates if the link has been established/not established.
1.3.6.1.4.1.10728.2.10.2.1.2.3Scalaran80iIfRxPacketsread-onlycurrentIndicates the number of received wireless packets with a correct CRC.
1.3.6.1.4.1.10728.2.10.2.1.2.4Scalaran80iIfRxPacketsReTxread-onlycurrentIndicates the number of received retransmitted wireless packets with a correct CRC.
1.3.6.1.4.1.10728.2.10.2.1.2.5Scalaran80iIfRxPacketsDiscread-onlycurrentIndicates the number of received retransmitted wireless packets with bad CRC.
1.3.6.1.4.1.10728.2.10.2.1.2.6Scalaran80iIfTxPacketsread-onlycurrentIndicates the number of transmitted packets that were received correctly by the other equipment.
1.3.6.1.4.1.10728.2.10.2.1.2.7Scalaran80iIfTxPacketsReTxread-onlycurrentIndicates the number of retransmitted wireless packets received correctly by the other equipment.
1.3.6.1.4.1.10728.2.10.2.1.2.8Scalaran80iIfTxPacketsDiscread-onlycurrentIndicates the number of retransmitted wireless packets that were not received correctly by the other equipment
1.3.6.1.4.1.10728.2.10.2.1.2.9Scalaran80iIfRssiMinread-onlycurrentIndicates the minimum received signal strength for the measuring interval.
1.3.6.1.4.1.10728.2.10.2.1.2.10Scalaran80iIfRssiMeanread-onlycurrentIndicates the average received signal strength for the measuring interval.
1.3.6.1.4.1.10728.2.10.2.1.2.11Scalaran80iIfRssiMaxread-onlycurrentIndicates the maximum received signal strength for the measuring interval.
1.3.6.1.4.1.10728.2.10.2.1.2.12Scalaran80iIfAvrSinAdrread-onlycurrentIndicates the Signal to interference, noise and distortion ratio.
1.3.6.1.4.1.10728.2.10.2.2NoderedlineAn80iIfPmpObjects
1.3.6.1.4.1.10728.2.10.2.2.1NoderedlineAn80iIfPmpSsObjects
1.3.6.1.4.1.10728.2.10.2.2.1.1Scalaran80iIfLastMissedMacAddressread-onlycurrentMAC address for the last SS that attempted to register but it was not present in the 'Links' table
1.3.6.1.4.1.10728.2.10.2.2.1.2Scalaran80iIfLastRegistMacAddressread-onlycurrentMAC address for the last SS that successfuly registered
1.3.6.1.4.1.10728.2.10.2.2.1.3Scalaran80iIfDenyMacAddressread-writecurrentMAC address for the SS that will be denied by this SC
1.3.6.1.4.1.10728.2.10.2.2.1.4Scalaran80iIfLastRegistLinkIdread-onlycurrentThe link ID for the last SS that successfully registered
1.3.6.1.4.1.10728.2.10.2.2.2Tablean80iIfPmpLinkConfigTablenot-accessiblecurrentThis table contains the PMP link configuration information.
1.3.6.1.4.1.10728.2.10.2.2.2.1Rowan80iIfPmpLinkConfigEntrynot-accessiblecurrentThis table provides one row for each PMP link that has been configured in the SC.
1.3.6.1.4.1.10728.2.10.2.2.2.1.1Columnan80iIfPmpLinkIdnot-accessiblecurrentThe PMP Link Identifier.
1.3.6.1.4.1.10728.2.10.2.2.2.1.2Columnan80iIfPmpLinkNameread-createcurrentThe PMP Link Name.
1.3.6.1.4.1.10728.2.10.2.2.2.1.3Columnan80iIfPmpLinkPeerMacAddressread-createcurrentThe MAC address for the peer SS
1.3.6.1.4.1.10728.2.10.2.2.2.1.4Columnan80iIfPmpLinkULBurstRateread-createcurrentUser supplied index of the uplink uncoded burst rate.
1.3.6.1.4.1.10728.2.10.2.2.2.1.5Columnan80iIfPmpLinkDLBurstRateread-createcurrentUser supplied index of the downlink uncoded burst rate.
1.3.6.1.4.1.10728.2.10.2.2.2.1.6Columnan80iIfPmpLinkConfigStatusread-createcurrentThis object is used to create a new row or modify or delete an existing row in this table.
1.3.6.1.4.1.10728.2.10.2.2.3Tablean80iIfPmpLinkStatsTablenot-accessiblecurrentThis table contains the PMP link statistics information.
1.3.6.1.4.1.10728.2.10.2.2.3.1Rowan80iIfPmpLinkStatsEntrynot-accessiblecurrentThis table provides one row for each PMP link that has been configured in the Service Controller.
1.3.6.1.4.1.10728.2.10.2.2.3.1.1Columnan80iIfPmpLinkStatusread-onlycurrentIndicates if the link has been established/not established.
1.3.6.1.4.1.10728.2.10.2.2.3.1.2Columnan80iIfPmpLinkStatusCoderead-onlycurrentIndicates the error code for the link.
1.3.6.1.4.1.10728.2.10.2.2.3.1.3Columnan80iIfRegPmpLinkConnsread-onlycurrentIndicates the registered connections for this Link.
1.3.6.1.4.1.10728.2.10.2.2.3.1.4Columnan80iIfPmpLinkUpTimeread-onlycurrentThe time (in hundredths of a second) elapsed since the link was established (up) last time.
1.3.6.1.4.1.10728.2.10.2.2.3.1.5Columnan80iIfPmpLinkLostCountread-onlycurrentNumber of times the link has been lost since the system started.
1.3.6.1.4.1.10728.2.10.2.2.3.1.6Columnan80iIfPmpLinkCurrDLUncBurstRateread-onlycurrentIndicates the index of the link's downlink actual uncoded burst rate.
1.3.6.1.4.1.10728.2.10.2.2.3.1.7Columnan80iIfPmpLinkDLRssiread-onlycurrentIndicates the link's DL RSSI (Received Signal Strength Indicator).
1.3.6.1.4.1.10728.2.10.2.2.3.1.8Columnan80iIfPmpLinkDLSinAdrread-onlycurrentIndicates the link's DL SINADR (Signal Interference and Noise Distorsion Ratio).
1.3.6.1.4.1.10728.2.10.2.2.3.1.9Columnan80iIfPmpLinkDLLostFrmread-onlycurrentIndicates the link's DL lost frames.
1.3.6.1.4.1.10728.2.10.2.2.3.1.10Columnan80iIfPmpLinkDLBlksTotread-onlycurrentIndicates the link's DL blocks transmitted.
1.3.6.1.4.1.10728.2.10.2.2.3.1.11Columnan80iIfPmpLinkDLBlksRetrread-onlycurrentIndicates the link's DL block re-transmitted.
1.3.6.1.4.1.10728.2.10.2.2.3.1.12Columnan80iIfPmpLinkDLBlksDiscread-onlycurrentIndicates the link's DL blocks lost
1.3.6.1.4.1.10728.2.10.2.2.3.1.13Columnan80iIfPmpLinkCurrULUncBurstRateread-onlycurrentIndicates the index of the link's uplink actual uncoded burst rate.
1.3.6.1.4.1.10728.2.10.2.2.3.1.14Columnan80iIfPmpLinkULRssiread-onlycurrentIndicates the link's UL RSSI (Received Signal Strength Indicator).
1.3.6.1.4.1.10728.2.10.2.2.3.1.15Columnan80iIfPmpLinkULSinAdrread-onlycurrentIndicates the link's UL SINADR (Signal Interference and Noise Distorsion Ratio).
1.3.6.1.4.1.10728.2.10.2.2.3.1.16Columnan80iIfPmpLinkULLostFrmread-onlycurrentIndicates the link's UL lost frames.
1.3.6.1.4.1.10728.2.10.2.2.3.1.17Columnan80iIfPmpLinkULBlksTotread-onlycurrentIndicates the link's UL blocks transmitted.
1.3.6.1.4.1.10728.2.10.2.2.3.1.18Columnan80iIfPmpLinkULBlksRetrread-onlycurrentIndicates the link's UL block re-transmitted.
1.3.6.1.4.1.10728.2.10.2.2.3.1.19Columnan80iIfPmpLinkULBlksDiscread-onlycurrentIndicates the link's UL blocks lost
1.3.6.1.4.1.10728.2.10.2.2.3.1.20Columnan80iIfPmpLinkStatsStatusread-onlycurrentThis object is used to create a new row or modify or delete an existing row in this table.
1.3.6.1.4.1.10728.2.10.2.2.4Tablean80iIfPmpGroupConfigTablenot-accessiblecurrentThis table contains group configuration information. The group defined as a broadcast domain.
1.3.6.1.4.1.10728.2.10.2.2.4.1Rowan80iIfPmpGroupConfigEntrynot-accessiblecurrentThis table provides one row for each group defined in the Service Controller
1.3.6.1.4.1.10728.2.10.2.2.4.1.1Columnan80iIfPmpGroupIdnot-accessiblecurrentThe PMP Group Identifier.
1.3.6.1.4.1.10728.2.10.2.2.4.1.2Columnan80iIfPmpGroupNameread-createcurrentThe PMP Group Name.
1.3.6.1.4.1.10728.2.10.2.2.4.1.3Columnan80iIfPmpGroupTaggingControlread-createcurrentSpecifies tagging mode.Only one pass-through group can exist. This is the default group. In the pass-through mode all the Ethernet packets that do not have a V…
1.3.6.1.4.1.10728.2.10.2.2.4.1.4Columnan80iIfPmpGroupVlanIdread-createcurrentIn the tagged mode all Ethernet packets that have this VID will be classified to belong to this group.
1.3.6.1.4.1.10728.2.10.2.2.4.1.5Columnan80iIfPmpGroupDefPriorityread-createcurrentThis field is used every time a tag is added at the exit point. The priority will be the one specified at the entry point.
1.3.6.1.4.1.10728.2.10.2.2.4.1.6Columnan80iIfPmpGroupSCEtherControlread-createcurrentMakes the Sector Controller a member of the group.
1.3.6.1.4.1.10728.2.10.2.2.4.1.7Columnan80iIfPmpGroupQosLevelread-createcurrentQoS level (index) that will affect the bandwidth and the delay for this group.
1.3.6.1.4.1.10728.2.10.2.2.4.1.8Columnan80iIfPmpGroupConfigStatusread-createcurrentThis object is used to create a new row or modify or delete an existing row in this table.
1.3.6.1.4.1.10728.2.10.2.2.4.1.9Columnan80iIfPmpGroupRateread-createcurrentDefine the index of the group rate. (0..7, 8=auto)
1.3.6.1.4.1.10728.2.10.2.2.4.1.10Columnan80iIfPmpGroupSStoSSMulticastread-createcurrentEnable the Subscriber to subscriber multicast traffic.
1.3.6.1.4.1.10728.2.10.2.2.5Tablean80iIfPmpGroupStatsTablenot-accessiblecurrentThis table contains group statistics information. The group defined as a broadcast domain.
1.3.6.1.4.1.10728.2.10.2.2.5.1Rowan80iIfPmpGroupStatsEntrynot-accessiblecurrentThis table provides one row for each group defined in the Service Controller
1.3.6.1.4.1.10728.2.10.2.2.5.1.1Columnan80iIfPmpGroupPacketsTxread-onlycurrentBroadcast/multicast Ethernet packets classified and transmitted to the group.
1.3.6.1.4.1.10728.2.10.2.2.5.1.2Columnan80iIfPmpGroupPacketDiscread-onlycurrentEthernet packets classified to be sent to the group but discarded due to unavailable memory.
1.3.6.1.4.1.10728.2.10.2.2.5.1.3Columnan80iIfPmpGroupStatsStatusread-onlycurrentThis object is used to create a new row or modify or delete an existing row in this table.
1.3.6.1.4.1.10728.2.10.2.2.6Tablean80iIfPmpConnConfigTablenot-accessiblecurrentThis table contains connections configuration information. One connection defines the transport parameter for Ethernet packets that have specific properties.
1.3.6.1.4.1.10728.2.10.2.2.6.1Rowan80iIfPmpConnConfigEntrynot-accessiblecurrentThis table provides one row for each connection defined in the Service Controller
1.3.6.1.4.1.10728.2.10.2.2.6.1.1Columnan80iIfPmpConnIdnot-accessiblecurrentThe PMP Conn Identifier.
1.3.6.1.4.1.10728.2.10.2.2.6.1.2Columnan80iIfPmpConnNameread-createcurrentThe PMP Conn Name.
1.3.6.1.4.1.10728.2.10.2.2.6.1.3Columnan80iIfPmpConnTaggingControlread-createcurrentSpecifies tagging mode. Only one pass-through connection can be defined on each link. This is the default connection. All the untagged packets or with a VID th…
1.3.6.1.4.1.10728.2.10.2.2.6.1.4Columnan80iIfPmpConnVlanIdread-createcurrentSpecifies VLAN Id for the tagged mode.
1.3.6.1.4.1.10728.2.10.2.2.6.1.5Columnan80iIfPmpConnDefPriorityread-createcurrentThis field is used every time a tag is added at the exit point. The priority will be the one specified at the entry point.
1.3.6.1.4.1.10728.2.10.2.2.6.1.6Columnan80iIfPmpConnDefParentLinkread-createcurrentThis object specifies the parent link of the connection.
1.3.6.1.4.1.10728.2.10.2.2.6.1.7Columnan80iIfPmpConnDefParenGroupread-createcurrentThis object specifies the parent group of the connection.
1.3.6.1.4.1.10728.2.10.2.2.6.1.8Columnan80iIfPmpConnDLQosread-createcurrentConnection QoS level (index) that will affect the DL bandwidth and the delay.
1.3.6.1.4.1.10728.2.10.2.2.6.1.9Columnan80iIfPmpConnULQosread-createcurrentConnection QoS level (index) that will affect the UL bandwidth and the delay.
1.3.6.1.4.1.10728.2.10.2.2.6.1.10Columnan80iIfPmpConnConfigStatusread-createcurrentThis object is used to create a new row or modify or delete an existing row in this table.
1.3.6.1.4.1.10728.2.10.2.2.7Tablean80iIfPmpConnStatsTablenot-accessiblecurrentThis table contains connections configuration information. One connection defines the transport parameter for Ethernet packets that have specific properties.
1.3.6.1.4.1.10728.2.10.2.2.7.1Rowan80iIfPmpConnStatsEntrynot-accessiblecurrentThis table provides one row for each connection defined in the Service Controller
1.3.6.1.4.1.10728.2.10.2.2.7.1.1Columnan80iIfPmpConnDLPacketsTxread-onlycurrentIndicates Ethernet packets sent by SC.
1.3.6.1.4.1.10728.2.10.2.2.7.1.2Columnan80iIfPmpConnDLPacketsRxread-onlycurrentIndicates Ethernet packets receivedby SS.
1.3.6.1.4.1.10728.2.10.2.2.7.1.3Columnan80iIfPmpConnDLPacketsDiscread-onlycurrentIndicates packets discarded due to full buffer.
1.3.6.1.4.1.10728.2.10.2.2.7.1.4Columnan80iIfPmpConnULPacketsTxread-onlycurrentIndicates Ethernet packets sent by SS.
1.3.6.1.4.1.10728.2.10.2.2.7.1.5Columnan80iIfPmpConnULPacketsRxread-onlycurrentIndicates Ethernet packets received SC.
1.3.6.1.4.1.10728.2.10.2.2.7.1.6Columnan80iIfPmpConnULPacketsDiscread-onlycurrentIndicates packets discarded due to full buffer.
1.3.6.1.4.1.10728.2.10.2.2.7.1.7Columnan80iIfPmpConnStatsStatusread-onlycurrentThis object is used to create a new row or modify or delete an existing row in this table.
1.3.6.1.4.1.10728.2.10.2.4NoderedlineAn80iIfConformance
1.3.6.1.4.1.10728.2.10.2.4.1NoderedlineAn80iIfGroups
1.3.6.1.4.1.10728.2.10.2.4.1.1GroupredlineAn80iIfPtpGroupcurrentPoint to point link objects.
1.3.6.1.4.1.10728.2.10.2.4.1.2GroupredlineAn80iIfPmpGroupcurrentPoint to multipoint link objects.
1.3.6.1.4.1.10728.2.10.2.4.1.3GroupredlineAn80iIfNotificationGroupcurrentThe notifications which indicate specific events within the AN80i interface.
1.3.6.1.4.1.10728.2.10.2.4.2NoderedlineAn80iIfCompls
1.3.6.1.4.1.10728.2.10.2.4.2.1ComplianceredlineAn80iIfCompliancecurrentThe compliance statement for SNMP entities that implement this MIB module.
MIB Viewer