REDLINE-AN80I-MIB
75 objects
This MIB module contains object definitions applicable only to Redline AN80i switched device.
Imported Objects
| INET-ADDRESS-MIB | InetAddress InetAddressType InetPortNumber |
| REDLINE-MIB | redlineSystem |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks |
| SNMPv2-TC | DisplayString RowStatus |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.10728.2.1.3 | IdentityredlineAn80iMib | This MIB module contains object definitions applicable only to Redline AN80i switched device. | ||
| 1.3.6.1.4.1.10728.2.1.3.0 | NoderedlineAn80iTrapDefinitions | |||
| 1.3.6.1.4.1.10728.2.1.3.0.1 | Notificationan80iPswdChangeFailTrap | current | An event to report the failure of a password change. | |
| 1.3.6.1.4.1.10728.2.1.3.0.2 | Notificationan80iFirmwareConfigFailTrap | current | An event to report the failure of a firmware config. | |
| 1.3.6.1.4.1.10728.2.1.3.0.3 | Notificationan80iEepromCorruptedTrap | current | An event to report the corruption of the EEPROM. | |
| 1.3.6.1.4.1.10728.2.1.3.0.4 | Notificationan80iHardwareFailTrap | current | An event to report the hardware failure. | |
| 1.3.6.1.4.1.10728.2.1.3.0.5 | Notificationan80iSaveConfigTrap | current | An event to report the saving of configuration | |
| 1.3.6.1.4.1.10728.2.1.3.0.6 | Notificationan80iDFSEventTrap | current | An event to report the radar frequency detection | |
| 1.3.6.1.4.1.10728.2.1.3.0.7 | Notificationan80iIdChangedTrap | current | Event that reports the modification in the configuration of an ID. | |
| 1.3.6.1.4.1.10728.2.1.3.0.8 | Notificationan80iSWUpgradeFailed | current | Event that reports the failure of a software upgrade opration. | |
| 1.3.6.1.4.1.10728.2.1.3.0.9 | Notificationan80iSWUpgradeSuccess | current | Event that reports the success of a software upgrade opration. | |
| 1.3.6.1.4.1.10728.2.1.3.1 | NoderedlineAn80iPtpPmpObjects | |||
| 1.3.6.1.4.1.10728.2.1.3.1.1 | NoderedlineAn80iSystemObjects | |||
| 1.3.6.1.4.1.10728.2.1.3.1.1.1 | Tablean80iOptionsKeyTable | not-accessible | current | This table contains options key information. The maximum number of configured options key is 2. |
| 1.3.6.1.4.1.10728.2.1.3.1.1.1.1 | Rowan80iOptionsKeyEntry | not-accessible | current | This table provides one row for each option key defined in the AN80i system |
| 1.3.6.1.4.1.10728.2.1.3.1.1.1.1.1 | Columnan80iOptionsKeyId | not-accessible | current | The Options Key Identifier. |
| 1.3.6.1.4.1.10728.2.1.3.1.1.1.1.2 | Columnan80iOptionsKey | read-create | current | The options key value. |
| 1.3.6.1.4.1.10728.2.1.3.1.1.1.1.3 | Columnan80iOptionsKeyStatus | read-create | current | This object is used to ctivate and deactivate rows in the an80iOptionsKeyTable table. There will be only two rows in the table and only one will be active. Whe… |
| 1.3.6.1.4.1.10728.2.1.3.1.1.2 | Scalaran80iHardwareType | read-only | current | The type/version/revision of the hardware. |
| 1.3.6.1.4.1.10728.2.1.3.1.1.3 | Scalaran80iRadioType | read-only | current | The radio type. |
| 1.3.6.1.4.1.10728.2.1.3.1.1.4 | Scalaran80iSaveConfig | read-write | current | This object will save the configuration in the nonvolatile memory and will activate the new configuration. |
| 1.3.6.1.4.1.10728.2.1.3.1.1.5 | Scalaran80iActivateConfig | read-write | current | This object will activate the new configuration without saving it in the nonvolatile memory. If after this event it will elapse more than 5 minutes and no save… |
| 1.3.6.1.4.1.10728.2.1.3.1.2 | NoderedlineAn80iWirelesObjects | |||
| 1.3.6.1.4.1.10728.2.1.3.1.2.1 | Scalaran80iAntennaAllignmentMode | read-write | current | Specifies if the antenna alignment buzzer is enabled or not. In the future, new alignment methods may be added. |
| 1.3.6.1.4.1.10728.2.1.3.1.2.2 | Scalaran80iCurrTxPower | read-only | current | The actual Tx Power of the AN-80i Node. |
| 1.3.6.1.4.1.10728.2.1.3.1.2.3 | Scalaran80iChannelAutoScan | read-write | current | Specifies if the frequency auto-scanning feature is enabled |
| 1.3.6.1.4.1.10728.2.1.3.1.2.4 | Scalaran80iCurrFrequency | read-only | current | The central frequency on which the equipment operates. If the auto-scanning feature is enabled then this may be different than the an80iOPeratingFrequency. [KH… |
| 1.3.6.1.4.1.10728.2.1.3.1.2.5 | Scalaran80iOPeratingFrequency | read-write | current | Specifies the operating frequency of the system [KHz]. |
| 1.3.6.1.4.1.10728.2.1.3.1.2.6 | Scalaran80iMaxTxPower | read-write | current | The Tx Power of the AN-80i. Specifies the power level of the system, which is preset at the factory and should not be altered. In the event that this parameter… |
| 1.3.6.1.4.1.10728.2.1.3.1.2.7 | Scalaran80iSystemMode | read-write | current | 1 = PMP Slave, 2 = PTP Master, 3 = PMP Slave, 4 = PMP Master |
| 1.3.6.1.4.1.10728.2.1.3.1.2.8 | Scalaran80iRFStatusCode | read-only | current | Specifies the Error Code for the RF Interface. |
| 1.3.6.1.4.1.10728.2.1.3.1.2.9 | Scalaran80iDFSAction | read-write | current | Action taken when a radar is detected on the same frequency. |
| 1.3.6.1.4.1.10728.2.1.3.1.2.10 | Scalaran80iAntennaGain | read-write | current | The gain of the antenna attached to the system. |
| 1.3.6.1.4.1.10728.2.1.3.1.2.11 | Scalaran80iActiveRFLinks | read-only | current | The actual number of provisioned links. |
| 1.3.6.1.4.1.10728.2.1.3.1.2.12 | Scalaran80iAtpControl | read-write | current | Enable/disable the automatic Tx power control. |
| 1.3.6.1.4.1.10728.2.1.3.1.2.13 | Scalaran80iTurboModeControl | read-write | current | Enable/disable the turbo mode. In this mode the system uses a 40MHz channel (20 MHz in normal mode). |
| 1.3.6.1.4.1.10728.2.1.3.1.2.14 | Scalaran80iChannelWidth | read-write | current | The width of the channel. |
| 1.3.6.1.4.1.10728.2.1.3.1.3 | NoderedlineAn80iEthernetObjects | |||
| 1.3.6.1.4.1.10728.2.1.3.1.3.1 | Scalaran80iEtherPortConn | read-write | current | Specifies Ethernet port connection auto(1), mdi(2) or mdix(3) |
| 1.3.6.1.4.1.10728.2.1.3.1.3.2 | Scalaran80iEtherPortMode | read-write | current | The attribute specifies the Ethernet LED status of the AN80i. |
| 1.3.6.1.4.1.10728.2.1.3.1.3.3 | Scalaran80iFlowControl | read-write | current | This object specifies if flow control is enabled or not. |
| 1.3.6.1.4.1.10728.2.1.3.1.3.4 | Scalaran80iLowLatencyMode | read-write | current | This object specifies if prioritized low latency mode is enabled or not. |
| 1.3.6.1.4.1.10728.2.1.3.1.3.5 | Scalaran80iEthernetFollowsWireless | read-write | current | This object specifies if the Ethernet follows wireless mode is enabled or not. |
| 1.3.6.1.4.1.10728.2.1.3.1.3.6 | Scalaran80iEthernetFollowsWirelessTimeout | read-write | current | This object specifies if the timeout (seconds) for the Ethernet follows wireless mode (0=infinite). |
| 1.3.6.1.4.1.10728.2.1.3.1.4 | NoderedlineAn80iManagObjects | |||
| 1.3.6.1.4.1.10728.2.1.3.1.4.1 | Scalaran80iHttpAccess | read-write | current | This object specifies if Http Access is enabled or not. |
| 1.3.6.1.4.1.10728.2.1.3.1.4.2 | Scalaran80iTelnetAccess | read-write | current | This object specifies if Telnet Access is enabled or not. |
| 1.3.6.1.4.1.10728.2.1.3.1.4.3 | Scalaran80iTelnetPort | read-write | current | This object specifies the Telnet port number. |
| 1.3.6.1.4.1.10728.2.1.3.1.5 | NoderedlineAn80iSWUpgradeObjects | |||
| 1.3.6.1.4.1.10728.2.1.3.1.5.1 | Scalaran80iSwDownloadTftpAddressType | read-write | current | The INET address type of the software upgrade TFTP server. IPv4 type supported only. |
| 1.3.6.1.4.1.10728.2.1.3.1.5.2 | Scalaran80iSwDownloadTftpAddress | read-write | current | The INET address of the TFTP server. |
| 1.3.6.1.4.1.10728.2.1.3.1.5.3 | Scalaran80iSwDownloadTftpFile | read-write | current | The image file name as required by the TFTP server. |
| 1.3.6.1.4.1.10728.2.1.3.1.5.4 | Scalaran80iSwDownloadStatus | read-only | current | The status of the current software download. |
| 1.3.6.1.4.1.10728.2.1.3.1.5.5 | Scalaran80iSwDownloadControl | read-write | current | Trigger software upgrade |
| 1.3.6.1.4.1.10728.2.1.3.2 | NoderedlineAn80iPmpObjects | |||
| 1.3.6.1.4.1.10728.2.1.3.2.1 | NoderedlineAn80iPmpWirelesObjects | |||
| 1.3.6.1.4.1.10728.2.1.3.2.1.1 | Scalaran80iRegistrationPeriod | read-write | current | Number of frames between two consecutive registration periods. |
| 1.3.6.1.4.1.10728.2.1.3.2.1.2 | Scalaran80iMaximumDistance | read-write | current | Maximum distance in km between the sector controller and one subscriber station. |
| 1.3.6.1.4.1.10728.2.1.3.2.1.3 | Scalaran80iRegisteredStations | read-only | current | The number of registered stations on the sector controller. |
| 1.3.6.1.4.1.10728.2.1.3.2.1.4 | Scalaran80iRegisteredConnections | read-only | current | The number of registered connections on the sector controller. |
| 1.3.6.1.4.1.10728.2.1.3.2.1.5 | Scalaran80iMaxId | read-only | current | The maximum number of ID used to identify links, connections and groups |
| 1.3.6.1.4.1.10728.2.1.3.2.1.6 | Scalaran80iNextAvailId | read-only | current | The next available ID from the ID pool which is not grater then that defined in 'an80iMaxId' |
| 1.3.6.1.4.1.10728.2.1.3.2.1.7 | Scalaran80iLastModifId | read-only | current | The last modified ID from the ID pool which is not grater then that defined in 'an80iMaxId' |
| 1.3.6.1.4.1.10728.2.1.3.2.1.8 | Scalaran80iSaveIdConfiguration | read-write | current | Save the ID table in the flash memory |
| 1.3.6.1.4.1.10728.2.1.3.3 | NoderedlineAn80iPtpObjects | |||
| 1.3.6.1.4.1.10728.2.1.3.3.1 | NoderedlineAn80iPtpSystemObjects | |||
| 1.3.6.1.4.1.10728.2.1.3.3.1.1 | Scalaran80iResetStatistics | read-write | current | This object resets wireless and Ethernet counters |
| 1.3.6.1.4.1.10728.2.1.3.5 | NoderedlineAn80iConformance | |||
| 1.3.6.1.4.1.10728.2.1.3.5.1 | NoderedlineAn80iGroups | |||
| 1.3.6.1.4.1.10728.2.1.3.5.1.1 | GroupredlineAn80iPtpPmpGroup | current | AN80i PTP/PMP objects. | |
| 1.3.6.1.4.1.10728.2.1.3.5.1.2 | GroupredlineAn80iPmpGroup | current | AN80i PMP objects. | |
| 1.3.6.1.4.1.10728.2.1.3.5.1.3 | GroupredlineAn80iPtpGroup | current | AN80i PTP objects. | |
| 1.3.6.1.4.1.10728.2.1.3.5.1.4 | GroupredlineAn80iNotificationGroup | current | The notifications which indicate specific events within the AN80i unit. | |
| 1.3.6.1.4.1.10728.2.1.3.5.2 | NoderedlineAn80iCompls | |||
| 1.3.6.1.4.1.10728.2.1.3.5.2.1 | ComplianceredlineAn80iCompliance | current | The compliance statement for AN80i entities that implement this MIB module. |