RITTAL-CMC-TC-MIB
270 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | enterprises |
| RFC1213-MIB | DisplayString sysContact sysDescr sysLocation sysName |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2606 | Noderittal | |||
| 1.3.6.1.4.1.2606.4 | NodecmcTc | |||
| 1.3.6.1.4.1.2606.4.1 | NodealarmSensorUnit1 | Alarm of sensor unit 1 | ||
| 1.3.6.1.4.1.2606.4.1 | NodecmcTcMibRev | |||
| 1.3.6.1.4.1.2606.4.1.1 | ScalarcmcTcMibMajRev | read-only | mandatory | The Major Revision level. A change in the major revision level represents a major change in the architecture of the MIB. A change in the major revision level m… |
| 1.3.6.1.4.1.2606.4.1.2 | ScalarcmcTcMibMinRev | read-only | mandatory | The Minor Revision level. A change in the minor revision level may represent some minor additional support, no changes to any pre-existing information has occu… |
| 1.3.6.1.4.1.2606.4.1.3 | ScalarcmcTcMibCondition | read-only | mandatory | The overall condition (status) of the system represented by this MIB. (2) OK (3) a minor problem, warning condition (yellow LED on CMC) (4) a major problem (re… |
| 1.3.6.1.4.1.2606.4.2 | NodealarmSensorUnit2 | Alarm of sensor unit 2 | ||
| 1.3.6.1.4.1.2606.4.2 | NodecmcTcStatus | |||
| 1.3.6.1.4.1.2606.4.2.1 | ScalarcmcTcStatusDeviceCMC | read-only | mandatory | General Status of CMC-TC unit itself (1) failed (2) OK |
| 1.3.6.1.4.1.2606.4.2.2 | ScalarcmcTcUnitsConnected | read-only | mandatory | Number of sensor units connected to the CMC, Port 1 to 4 |
| 1.3.6.1.4.1.2606.4.2.3 | NodecmcTcStatusSensorUnit1 | |||
| 1.3.6.1.4.1.2606.4.2.3.1 | ScalarcmcTcUnit1TypeOfDevice | read-only | mandatory | Type of sensor unit connected to port 1 |
| 1.3.6.1.4.1.2606.4.2.3.2 | ScalarcmcTcUnit1Text | read-write | mandatory | Descriptional text for sensor unit connected to port 1 |
| 1.3.6.1.4.1.2606.4.2.3.3 | ScalarcmcTcUnit1Serial | read-only | mandatory | Serialnumber of sensor unit connected to port 1 |
| 1.3.6.1.4.1.2606.4.2.3.4 | ScalarcmcTcUnit1Status | read-only | mandatory | General Status sensor unit connected to port 1 (1) OK (2) error, e. g. value overflow (3) configuration of sensor unit has changed, confirmation required (4) Q… |
| 1.3.6.1.4.1.2606.4.2.3.5 | NodecmcTcStatusUnit1Sensors | |||
| 1.3.6.1.4.1.2606.4.2.3.5.1 | ScalarcmcTcUnit1NumberOfSensors | read-only | mandatory | Number of sensors connected to sensor unit 1 |
| 1.3.6.1.4.1.2606.4.2.3.5.2 | TablecmcTcUnit1SensorTable | not-accessible | mandatory | Headline of sensor table |
| 1.3.6.1.4.1.2606.4.2.3.5.2.1 | RowcmcTcUnit1SensorEntry | not-accessible | mandatory | Entries of sensor table |
| 1.3.6.1.4.1.2606.4.2.3.5.2.1.1 | Columnunit1SensorIndex | read-only | mandatory | Index for the list of value entries. Its value ranges between 1 and the value of cmcTcUnit1NumberOfSensors. |
| 1.3.6.1.4.1.2606.4.2.3.5.2.1.2 | Columnunit1SensorType | read-only | mandatory | Type of sensor which is connected to sensor unit 1 to sensor[unit1SensorIndex] 1: no sensor connected 2: sensor failure 3: value overflow 4: sensor type 1, acc… |
| 1.3.6.1.4.1.2606.4.2.3.5.2.1.3 | Columnunit1SensorText | read-write | mandatory | Descriptional text for each sensor (entry in the table) |
| 1.3.6.1.4.1.2606.4.2.3.5.2.1.4 | Columnunit1SensorStatus | read-only | mandatory | Actual status of the sensor |
| 1.3.6.1.4.1.2606.4.2.3.5.2.1.5 | Columnunit1SensorValue | read-only | mandatory | Value of sensor |
| 1.3.6.1.4.1.2606.4.2.3.5.2.1.6 | Columnunit1SensorSetHigh | read-write | mandatory | Value for high setpoint of sensor |
| 1.3.6.1.4.1.2606.4.2.3.5.2.1.7 | Columnunit1SensorSetLow | read-write | mandatory | Value for low setpoint of sensor, also used as alarm delay |
| 1.3.6.1.4.1.2606.4.2.3.5.2.1.8 | Columnunit1SensorSetWarn | read-write | mandatory | Value for warning setpoint of sensor, also used as fan threshold |
| 1.3.6.1.4.1.2606.4.2.3.5.2.1.9 | Columnunit1SensorHysteresis | read-write | mandatory | % -Value for hysteresis for High, Low and Warning, input in % from actual setpoint |
| 1.3.6.1.4.1.2606.4.2.3.5.2.1.10 | Columnunit1SensorDisplayFactor | read-only | mandatory | Factor of sensor value and setpoints, devide actual value with this value, e. g. factor = 10: sensor value = 100, actual value = 10.0 |
| 1.3.6.1.4.1.2606.4.2.3.5.2.1.11 | Columnunit1SensorScaleStart | read-write | mandatory | Value for start value for scaling of 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to… |
| 1.3.6.1.4.1.2606.4.2.3.5.2.1.12 | Columnunit1SensorScaleEnd | read-write | mandatory | Value for end value for scaling of 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to 6… |
| 1.3.6.1.4.1.2606.4.2.3.5.2.1.13 | Columnunit1SensorUnit | read-write | mandatory | Unit for 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to 'A' |
| 1.3.6.1.4.1.2606.4.2.3.5.2.1.14 | Columnunit1SensorInfo | read-only | mandatory | Additional information to the sensor, e. g. Serialnumber, Signal Quality.. |
| 1.3.6.1.4.1.2606.4.2.3.6 | NodecmcTcStatusUnit1Outputs | |||
| 1.3.6.1.4.1.2606.4.2.3.6.1 | ScalarcmcTcUnit1NumberOfOutputs | read-only | mandatory | Number of outputs available on sensor unit 1 |
| 1.3.6.1.4.1.2606.4.2.3.6.2 | TablecmcTcUnit1OutputTable | not-accessible | mandatory | Headline of output table |
| 1.3.6.1.4.1.2606.4.2.3.6.2.1 | RowcmcTcUnit1OutputEntry | not-accessible | mandatory | Entries of output table |
| 1.3.6.1.4.1.2606.4.2.3.6.2.1.1 | Columnunit1OutputIndex | read-only | mandatory | Index for the list of output entries. Its value ranges between 1 and the value of cmcTcUnit1NumberOfOutputs. |
| 1.3.6.1.4.1.2606.4.2.3.6.2.1.2 | Columnunit1OutputType | read-only | mandatory | Type of output which is connected to sensor unit 1 to output[unit1OutputIndex] 1: no output connected 2: output failure 3: value overflow 4: output type 1, doo… |
| 1.3.6.1.4.1.2606.4.2.3.6.2.1.3 | Columnunit1OutputText | read-write | mandatory | Descriptional text for each output (entry in the table) |
| 1.3.6.1.4.1.2606.4.2.3.6.2.1.4 | Columnunit1OutputStatus | read-write | mandatory | Actual status of the output |
| 1.3.6.1.4.1.2606.4.2.3.6.2.1.5 | Columnunit1OutputValue | read-write | mandatory | Value for output |
| 1.3.6.1.4.1.2606.4.2.3.6.2.1.6 | Columnunit1OutputSet | read-write | mandatory | Command for output |
| 1.3.6.1.4.1.2606.4.2.3.6.2.1.7 | Columnunit1OutputConfig | read-write | mandatory | Configuration for output 1: disable remote control (e.g. keypad) 2: enable remote control |
| 1.3.6.1.4.1.2606.4.2.3.6.2.1.8 | Columnunit1OutputDelay | read-write | mandatory | Unsigned Value for delay, after this time the output will fall into the previous state |
| 1.3.6.1.4.1.2606.4.2.3.6.2.1.9 | Columnunit1OutputTimeoutAction | read-write | mandatory | State for output if timeout (RS422) occurs |
| 1.3.6.1.4.1.2606.4.2.3.7 | NodecmcTcStatusUnit1Msg | |||
| 1.3.6.1.4.1.2606.4.2.3.7.1 | ScalarcmcTcUnit1NumberOfMsgs | read-only | mandatory | Number of messages that can be created with sensor unit 1 |
| 1.3.6.1.4.1.2606.4.2.3.7.2 | TablecmcTcUnit1MsgTable | not-accessible | mandatory | Headline of message table |
| 1.3.6.1.4.1.2606.4.2.3.7.2.1 | RowcmcTcUnit1MsgEntry | not-accessible | mandatory | Entries of message table |
| 1.3.6.1.4.1.2606.4.2.3.7.2.1.1 | Columnunit1MsgIndex | read-only | mandatory | Index for the list of message entries. Its value ranges between 1 and the value of cmcTcUnit1NumberOfMsgs. |
| 1.3.6.1.4.1.2606.4.2.3.7.2.1.2 | Columnunit1MsgText | read-write | mandatory | Descriptional text for each message (entry in the table) |
| 1.3.6.1.4.1.2606.4.2.3.7.2.1.3 | Columnunit1MsgStatus | read-only | mandatory | Actual message status 1: not available 2: configuration has changed (sensor new, changed, lost) 3: error 4: OK 5: alarm, e.g. smoke, vibration... 6: warning of… |
| 1.3.6.1.4.1.2606.4.2.3.7.2.1.4 | Columnunit1MsgRelay | read-write | mandatory | Setup of Alarm relay for this message/alarm 1: no switching of alarm relay 2: switching of alarm relay |
| 1.3.6.1.4.1.2606.4.2.3.7.2.1.5 | Columnunit1MsgBeeper | read-write | mandatory | Setup of Alarm beeper for this alarm 1: no audible alarm 2: audible alarm |
| 1.3.6.1.4.1.2606.4.2.3.7.2.1.6 | Columnunit1MsgTrap1 | read-write | mandatory | Trap receiver 1 activated |
| 1.3.6.1.4.1.2606.4.2.3.7.2.1.7 | Columnunit1MsgTrap2 | read-write | mandatory | Trap receiver 2 activated |
| 1.3.6.1.4.1.2606.4.2.3.7.2.1.8 | Columnunit1MsgTrap3 | read-write | mandatory | Trap receiver 3 activated |
| 1.3.6.1.4.1.2606.4.2.3.7.2.1.9 | Columnunit1MsgTrap4 | read-write | mandatory | Trap receiver 4 and Event Logging activated |
| 1.3.6.1.4.1.2606.4.2.3.7.2.1.10 | Columnunit1MsgQuit | read-write | mandatory | Reset of this alarm 1: auto 2: manual, alarm needs confirmation, e. g. with 'C' key |
| 1.3.6.1.4.1.2606.4.2.3.7.2.1.11 | Columnunit1MsgDelay | read-write | mandatory | Delay of alarm condition |
| 1.3.6.1.4.1.2606.4.2.4 | NodecmcTcStatusSensorUnit2 | |||
| 1.3.6.1.4.1.2606.4.2.4.1 | ScalarcmcTcUnit2TypeOfDevice | read-only | mandatory | Type of sensor unit connected to port 2 |
| 1.3.6.1.4.1.2606.4.2.4.2 | ScalarcmcTcUnit2Text | read-write | mandatory | Descriptional text for sensor unit connected to port 2 |
| 1.3.6.1.4.1.2606.4.2.4.3 | ScalarcmcTcUnit2Serial | read-only | mandatory | Serialnumber of sensor unit connected to port 2 |
| 1.3.6.1.4.1.2606.4.2.4.4 | ScalarcmcTcUnit2Status | read-only | mandatory | General Status sensor unit connected to port 2 (1) OK (2) error (3) configuration of sensor unit has changed, confirmation required (4) Quit from sensor unit t… |
| 1.3.6.1.4.1.2606.4.2.4.5 | NodecmcTcStatusUnit2Sensors | |||
| 1.3.6.1.4.1.2606.4.2.4.5.1 | ScalarcmcTcUnit2NumberOfSensors | read-only | mandatory | Number of sensors connected to sensor unit 2 |
| 1.3.6.1.4.1.2606.4.2.4.5.2 | TablecmcTcUnit2SensorTable | not-accessible | mandatory | Headline of sensor table |
| 1.3.6.1.4.1.2606.4.2.4.5.2.1 | RowcmcTcUnit2SensorEntry | not-accessible | mandatory | Entries of sensor table |
| 1.3.6.1.4.1.2606.4.2.4.5.2.1.1 | Columnunit2SensorIndex | read-only | mandatory | Index for the list of value entries. Its value ranges between 1 and the value of cmcTcUnit2NumberOfSensors. |
| 1.3.6.1.4.1.2606.4.2.4.5.2.1.2 | Columnunit2SensorType | read-only | mandatory | Type of sensor which is connected to sensor unit 2 to sensor[unit2SensorIndex] 1: no sensor connected 2: sensor failure 3: value overflow 4: sensor type 1, acc… |
| 1.3.6.1.4.1.2606.4.2.4.5.2.1.3 | Columnunit2SensorText | read-write | mandatory | Descriptional text for each sensor (entry in the table) |
| 1.3.6.1.4.1.2606.4.2.4.5.2.1.4 | Columnunit2SensorStatus | read-only | mandatory | Actual status of the sensor |
| 1.3.6.1.4.1.2606.4.2.4.5.2.1.5 | Columnunit2SensorValue | read-only | mandatory | Value of sensor |
| 1.3.6.1.4.1.2606.4.2.4.5.2.1.6 | Columnunit2SensorSetHigh | read-write | mandatory | Value for high setpoint of sensor |
| 1.3.6.1.4.1.2606.4.2.4.5.2.1.7 | Columnunit2SensorSetLow | read-write | mandatory | Value for low setpoint of sensor, also used as alarm delay |
| 1.3.6.1.4.1.2606.4.2.4.5.2.1.8 | Columnunit2SensorSetWarn | read-write | mandatory | Value for warning setpoint of sensor, also used as fan threshold |
| 1.3.6.1.4.1.2606.4.2.4.5.2.1.9 | Columnunit2SensorHysteresis | read-write | mandatory | % -Value for hysteresis for High, Low and Warning, input in % from actual setpoint |
| 1.3.6.1.4.1.2606.4.2.4.5.2.1.10 | Columnunit2SensorDisplayFactor | read-only | mandatory | Factor of sensor value and setpoints, devide actual value with this value, e. g. factor = 10: sensor value = 100, actual value = 10.0 |
| 1.3.6.1.4.1.2606.4.2.4.5.2.1.11 | Columnunit2SensorScaleStart | read-write | mandatory | Value for start value for scaling of 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to… |
| 1.3.6.1.4.1.2606.4.2.4.5.2.1.12 | Columnunit2SensorScaleEnd | read-write | mandatory | Value for end value for scaling of 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to 6… |
| 1.3.6.1.4.1.2606.4.2.4.5.2.1.13 | Columnunit2SensorUnit | read-write | mandatory | Unit for 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to 'A' |
| 1.3.6.1.4.1.2606.4.2.4.5.2.1.14 | Columnunit2SensorInfo | read-only | mandatory | Additional information to the sensor, e. g. Serialnumber, Signal Quality.. |
| 1.3.6.1.4.1.2606.4.2.4.6 | NodecmcTcStatusUnit2Outputs | |||
| 1.3.6.1.4.1.2606.4.2.4.6.1 | ScalarcmcTcUnit2NumberOfOutputs | read-only | mandatory | Number of outputs available on sensor unit 2 |
| 1.3.6.1.4.1.2606.4.2.4.6.2 | TablecmcTcUnit2OutputTable | not-accessible | mandatory | Headline of output table |
| 1.3.6.1.4.1.2606.4.2.4.6.2.1 | RowcmcTcUnit2OutputEntry | not-accessible | mandatory | Entries of output table |
| 1.3.6.1.4.1.2606.4.2.4.6.2.1.1 | Columnunit2OutputIndex | read-only | mandatory | Index for the list of output entries. Its value ranges between 1 and the value of cmcTcUnit2NumberOfOutputs. |
| 1.3.6.1.4.1.2606.4.2.4.6.2.1.2 | Columnunit2OutputType | read-only | mandatory | Type of output which is connected to sensor unit 2 to output[unit2OutputIndex] 1: no output connected 2: output failure 3: value overflow 4: output type 1, doo… |
| 1.3.6.1.4.1.2606.4.2.4.6.2.1.3 | Columnunit2OutputText | read-write | mandatory | Descriptional text for each output (entry in the table) |
| 1.3.6.1.4.1.2606.4.2.4.6.2.1.4 | Columnunit2OutputStatus | read-write | mandatory | Actual status of the output |
| 1.3.6.1.4.1.2606.4.2.4.6.2.1.5 | Columnunit2OutputValue | read-write | mandatory | Signed value for output |
| 1.3.6.1.4.1.2606.4.2.4.6.2.1.6 | Columnunit2OutputSet | read-write | mandatory | Command for output |
| 1.3.6.1.4.1.2606.4.2.4.6.2.1.7 | Columnunit2OutputConfig | read-write | mandatory | Configuration for output 1: disable remote control (e.g. keypad) 2: enable remote control |
| 1.3.6.1.4.1.2606.4.2.4.6.2.1.8 | Columnunit2OutputDelay | read-write | mandatory | Unsigned Value for delay, after this time the output will fall into the previous state |
| 1.3.6.1.4.1.2606.4.2.4.6.2.1.9 | Columnunit2OutputTimeoutAction | read-write | mandatory | State for output if timeout (RS422) occurs |
| 1.3.6.1.4.1.2606.4.2.4.7 | NodecmcTcStatusUnit2Msg | |||
| 1.3.6.1.4.1.2606.4.2.4.7.1 | ScalarcmcTcUnit2NumberOfMsgs | read-only | mandatory | Number of alarms that can be created with sensor unit 2 |
| 1.3.6.1.4.1.2606.4.2.4.7.2 | TablecmcTcUnit2MsgTable | not-accessible | mandatory | Headline of message table |
| 1.3.6.1.4.1.2606.4.2.4.7.2.1 | RowcmcTcUnit2MsgEntry | not-accessible | mandatory | Entries of message table |
| 1.3.6.1.4.1.2606.4.2.4.7.2.1.1 | Columnunit2MsgIndex | read-only | mandatory | Index for the list of alarm entries. Its value ranges between 1 and the value of cmcTcUnit2NumberOfMsgs. |
| 1.3.6.1.4.1.2606.4.2.4.7.2.1.2 | Columnunit2MsgText | read-write | mandatory | Descriptional text for each message (entry in the table) |
| 1.3.6.1.4.1.2606.4.2.4.7.2.1.3 | Columnunit2MsgStatus | read-only | mandatory | Actual message status 1: not available 2: configuration has changed (sensor new, changed, lost) 3: error 4: OK 5: alarm, e.g. smoke, vibration... 6: warning of… |
| 1.3.6.1.4.1.2606.4.2.4.7.2.1.4 | Columnunit2MsgRelay | read-write | mandatory | Setup of Alarm relay for this alarm 2: no switching of alarm relay 1: switching of alarm relay |
| 1.3.6.1.4.1.2606.4.2.4.7.2.1.5 | Columnunit2MsgBeeper | read-write | mandatory | Setup of Alarm beeper for this alarm 2: no audible alarm 1: audible alarm |
| 1.3.6.1.4.1.2606.4.2.4.7.2.1.6 | Columnunit2MsgTrap1 | read-write | mandatory | Trap receiver 1 activated |
| 1.3.6.1.4.1.2606.4.2.4.7.2.1.7 | Columnunit2MsgTrap2 | read-write | mandatory | Trap receiver 2 activated |
| 1.3.6.1.4.1.2606.4.2.4.7.2.1.8 | Columnunit2MsgTrap3 | read-write | mandatory | Trap receiver 3 activated |
| 1.3.6.1.4.1.2606.4.2.4.7.2.1.9 | Columnunit2MsgTrap4 | read-write | mandatory | Trap receiver 4 and Event Logging activated |
| 1.3.6.1.4.1.2606.4.2.4.7.2.1.10 | Columnunit2MsgQuit | read-write | mandatory | Reset of this alarm 1: auto 2: manual, alarm needs confirmation, e. g. with 'C' key |
| 1.3.6.1.4.1.2606.4.2.4.7.2.1.11 | Columnunit2MsgDelay | read-write | mandatory | Delay of alarm condition |
| 1.3.6.1.4.1.2606.4.2.5 | NodecmcTcStatusSensorUnit3 | |||
| 1.3.6.1.4.1.2606.4.2.5.1 | ScalarcmcTcUnit3TypeOfDevice | read-only | mandatory | Type of sensor unit connected to port 3 |
| 1.3.6.1.4.1.2606.4.2.5.2 | ScalarcmcTcUnit3Text | read-write | mandatory | Descriptional text for sensor unit connected to port 3 |
| 1.3.6.1.4.1.2606.4.2.5.3 | ScalarcmcTcUnit3Serial | read-only | mandatory | Serialnumber of sensor unit connected to port 3 |
| 1.3.6.1.4.1.2606.4.2.5.4 | ScalarcmcTcUnit3Status | read-only | mandatory | General Status sensor unit connected to port 3 (1) OK (2) error, e. g. value overflow (3) configuration of sensor unit has changed, confirmation required (4) Q… |
| 1.3.6.1.4.1.2606.4.2.5.5 | NodecmcTcStatusUnit3Sensors | |||
| 1.3.6.1.4.1.2606.4.2.5.5.1 | ScalarcmcTcUnit3NumberOfSensors | read-only | mandatory | Number of sensors connected to sensor unit 3 |
| 1.3.6.1.4.1.2606.4.2.5.5.2 | TablecmcTcUnit3SensorTable | not-accessible | mandatory | Headline of sensor table |
| 1.3.6.1.4.1.2606.4.2.5.5.2.1 | RowcmcTcUnit3SensorEntry | not-accessible | mandatory | Entries of sensor table |
| 1.3.6.1.4.1.2606.4.2.5.5.2.1.1 | Columnunit3SensorIndex | read-only | mandatory | Index for the list of value entries. Its value ranges between 1 and the value of cmcTcUnit3NumberOfSensors. |
| 1.3.6.1.4.1.2606.4.2.5.5.2.1.2 | Columnunit3SensorType | read-only | mandatory | Type of sensor which is connected to sensor unit 3 to sensor[unit3SensorIndex] 1: no sensor connected 2: sensor failure 3: value overflow 4: sensor type 1, acc… |
| 1.3.6.1.4.1.2606.4.2.5.5.2.1.3 | Columnunit3SensorText | read-write | mandatory | Descriptional text for each sensor (entry in the table) |
| 1.3.6.1.4.1.2606.4.2.5.5.2.1.4 | Columnunit3SensorStatus | read-only | mandatory | Actual status of the sensor |
| 1.3.6.1.4.1.2606.4.2.5.5.2.1.5 | Columnunit3SensorValue | read-only | mandatory | Value of sensor |
| 1.3.6.1.4.1.2606.4.2.5.5.2.1.6 | Columnunit3SensorSetHigh | read-write | mandatory | Value for high setpoint of sensor |
| 1.3.6.1.4.1.2606.4.2.5.5.2.1.7 | Columnunit3SensorSetLow | read-write | mandatory | Value for low setpoint of sensor |
| 1.3.6.1.4.1.2606.4.2.5.5.2.1.8 | Columnunit3SensorSetWarn | read-write | mandatory | Value for warning setpoint of sensor, also used as fan threshold |
| 1.3.6.1.4.1.2606.4.2.5.5.2.1.9 | Columnunit3SensorHysteresis | read-write | mandatory | % -Value for hysteresis for High, Low and Warning, input in % from actual setpoint |
| 1.3.6.1.4.1.2606.4.2.5.5.2.1.10 | Columnunit3SensorDisplayFactor | read-only | mandatory | Factor of sensor value and setpoints, devide actual value with this value, e. g. factor = 10: sensor value = 100, actual value = 10.0 |
| 1.3.6.1.4.1.2606.4.2.5.5.2.1.11 | Columnunit3SensorScaleStart | read-write | mandatory | Value for start value for scaling of 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to… |
| 1.3.6.1.4.1.2606.4.2.5.5.2.1.12 | Columnunit3SensorScaleEnd | read-write | mandatory | Value for end value for scaling of 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to 6… |
| 1.3.6.1.4.1.2606.4.2.5.5.2.1.13 | Columnunit3SensorUnit | read-write | mandatory | Unit for 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to 'A' |
| 1.3.6.1.4.1.2606.4.2.5.5.2.1.14 | Columnunit3SensorInfo | read-only | mandatory | Additional information to the sensor, e. g. Serialnumber, Signal Quality.. |
| 1.3.6.1.4.1.2606.4.2.5.6 | NodecmcTcStatusUnit3Outputs | |||
| 1.3.6.1.4.1.2606.4.2.5.6.1 | ScalarcmcTcUnit3NumberOfOutputs | read-only | mandatory | Number of outputs available on sensor unit 3 |
| 1.3.6.1.4.1.2606.4.2.5.6.2 | TablecmcTcUnit3OutputTable | not-accessible | mandatory | Headline of output table |
| 1.3.6.1.4.1.2606.4.2.5.6.2.1 | RowcmcTcUnit3OutputEntry | not-accessible | mandatory | Entries of output table |
| 1.3.6.1.4.1.2606.4.2.5.6.2.1.1 | Columnunit3OutputIndex | read-only | mandatory | Index for the list of output entries. Its value ranges between 1 and the value of cmcTcUnit3NumberOfOutputs. |
| 1.3.6.1.4.1.2606.4.2.5.6.2.1.2 | Columnunit3OutputType | read-only | mandatory | Type of output which is connected to sensor unit 3 to output[unit3OutputIndex] 1: no output connected 2: output failure 3: value overflow 4: output type 1, doo… |
| 1.3.6.1.4.1.2606.4.2.5.6.2.1.3 | Columnunit3OutputText | read-write | mandatory | Descriptional text for each output (entry in the table) |
| 1.3.6.1.4.1.2606.4.2.5.6.2.1.4 | Columnunit3OutputStatus | read-write | mandatory | Actual status of the output |
| 1.3.6.1.4.1.2606.4.2.5.6.2.1.5 | Columnunit3OutputValue | read-write | mandatory | Value for output |
| 1.3.6.1.4.1.2606.4.2.5.6.2.1.6 | Columnunit3OutputSet | read-write | mandatory | Command for output |
| 1.3.6.1.4.1.2606.4.2.5.6.2.1.7 | Columnunit3OutputConfig | read-write | mandatory | Configuration for output 1: disable remote control (e.g. keypad) 2: enable remote control |
| 1.3.6.1.4.1.2606.4.2.5.6.2.1.8 | Columnunit3OutputDelay | read-write | mandatory | Unsigned Value for delay, after this time the output will fall into the previous state |
| 1.3.6.1.4.1.2606.4.2.5.6.2.1.9 | Columnunit3OutputTimeoutAction | read-write | mandatory | State for output if timeout (RS422) occurs |
| 1.3.6.1.4.1.2606.4.2.5.7 | NodecmcTcStatusUnit3Msg | |||
| 1.3.6.1.4.1.2606.4.2.5.7.1 | ScalarcmcTcUnit3NumberOfMsgs | read-only | mandatory | Number of alarms that can be created with sensor unit 3 |
| 1.3.6.1.4.1.2606.4.2.5.7.2 | TablecmcTcUnit3MsgTable | not-accessible | mandatory | Headline of message table |
| 1.3.6.1.4.1.2606.4.2.5.7.2.1 | RowcmcTcUnit3MsgEntry | not-accessible | mandatory | Entries of message table |
| 1.3.6.1.4.1.2606.4.2.5.7.2.1.1 | Columnunit3MsgIndex | read-only | mandatory | Index for the list of alarm entries. Its value ranges between 1 and the value of cmcTcUnit3NumberOfMsgs. |
| 1.3.6.1.4.1.2606.4.2.5.7.2.1.2 | Columnunit3MsgText | read-write | mandatory | Descriptional text for each message (entry in the table) |
| 1.3.6.1.4.1.2606.4.2.5.7.2.1.3 | Columnunit3MsgStatus | read-only | mandatory | Actual message status 1: not available 2: configuration has changed (sensor new, changed, lost) 3: error 4: OK 5: alarm, e.g. smoke, vibration... 6: warning of… |
| 1.3.6.1.4.1.2606.4.2.5.7.2.1.4 | Columnunit3MsgRelay | read-write | mandatory | Setup of Alarm relay for this alarm 1: no switching of alarm relay 2: switching of alarm relay |
| 1.3.6.1.4.1.2606.4.2.5.7.2.1.5 | Columnunit3MsgBeeper | read-write | mandatory | Setup of Alarm beeper for this alarm 1: no audible alarm 2: audible alarm |
| 1.3.6.1.4.1.2606.4.2.5.7.2.1.6 | Columnunit3MsgTrap1 | read-write | mandatory | Trap receiver 1 activated |
| 1.3.6.1.4.1.2606.4.2.5.7.2.1.7 | Columnunit3MsgTrap2 | read-write | mandatory | Trap receiver 2 activated |
| 1.3.6.1.4.1.2606.4.2.5.7.2.1.8 | Columnunit3MsgTrap3 | read-write | mandatory | Trap receiver 3 activated |
| 1.3.6.1.4.1.2606.4.2.5.7.2.1.9 | Columnunit3MsgTrap4 | read-write | mandatory | Trap receiver 4 and Event Logging activated |
| 1.3.6.1.4.1.2606.4.2.5.7.2.1.10 | Columnunit3MsgQuit | read-write | mandatory | Reset of this alarm 1: auto 2: manual, alarm needs confirmation, e. g. with 'C' key |
| 1.3.6.1.4.1.2606.4.2.5.7.2.1.11 | Columnunit3MsgDelay | read-write | mandatory | Delay of alarm condition |
| 1.3.6.1.4.1.2606.4.2.6 | NodecmcTcStatusSensorUnit4 | |||
| 1.3.6.1.4.1.2606.4.2.6.1 | ScalarcmcTcUnit4TypeOfDevice | read-only | mandatory | Type of sensor unit connected to port 4 |
| 1.3.6.1.4.1.2606.4.2.6.2 | ScalarcmcTcUnit4Text | read-write | mandatory | Descriptional text for sensor unit connected to port 4 |
| 1.3.6.1.4.1.2606.4.2.6.3 | ScalarcmcTcUnit4Serial | read-only | mandatory | Serialnumber of sensor unit connected to port 4 |
| 1.3.6.1.4.1.2606.4.2.6.4 | ScalarcmcTcUnit4Status | read-only | mandatory | General Status sensor unit connected to port 4 (1) OK (2) error, e. g. value overflow (3) configuration of sensor unit has changed, confirmation required (4) Q… |
| 1.3.6.1.4.1.2606.4.2.6.5 | NodecmcTcStatusUnit4Sensors | |||
| 1.3.6.1.4.1.2606.4.2.6.5.1 | ScalarcmcTcUnit4NumberOfSensors | read-only | mandatory | Number of sensors connected to sensor unit 4 |
| 1.3.6.1.4.1.2606.4.2.6.5.2 | TablecmcTcUnit4SensorTable | not-accessible | mandatory | Headline of sensor table |
| 1.3.6.1.4.1.2606.4.2.6.5.2.1 | RowcmcTcUnit4SensorEntry | not-accessible | mandatory | Entries of sensor table |
| 1.3.6.1.4.1.2606.4.2.6.5.2.1.1 | Columnunit4SensorIndex | read-only | mandatory | Index for the list of value entries. Its value ranges between 1 and the value of cmcTcUnit4NumberOfSensors. |
| 1.3.6.1.4.1.2606.4.2.6.5.2.1.2 | Columnunit4SensorType | read-only | mandatory | Type of sensor which is connected to sensor unit 4 to sensor[unit4SensorIndex] 1: no sensor connected 2: sensor failure 3: value overflow 4: sensor type 1, acc… |
| 1.3.6.1.4.1.2606.4.2.6.5.2.1.3 | Columnunit4SensorText | read-write | mandatory | Descriptional text for each sensor (entry in the table) |
| 1.3.6.1.4.1.2606.4.2.6.5.2.1.4 | Columnunit4SensorStatus | read-only | mandatory | Actual status of the sensor |
| 1.3.6.1.4.1.2606.4.2.6.5.2.1.5 | Columnunit4SensorValue | read-only | mandatory | Value of sensor |
| 1.3.6.1.4.1.2606.4.2.6.5.2.1.6 | Columnunit4SensorSetHigh | read-write | mandatory | Value for high setpoint of sensor |
| 1.3.6.1.4.1.2606.4.2.6.5.2.1.7 | Columnunit4SensorSetLow | read-write | mandatory | Value for low setpoint of sensor |
| 1.3.6.1.4.1.2606.4.2.6.5.2.1.8 | Columnunit4SensorSetWarn | read-write | mandatory | Value for warning setpoint of sensor, also used as fan threshold |
| 1.3.6.1.4.1.2606.4.2.6.5.2.1.9 | Columnunit4SensorHysteresis | read-write | mandatory | % -Value for hysteresis for High, Low and Warning, input in % from actual setpoint |
| 1.3.6.1.4.1.2606.4.2.6.5.2.1.10 | Columnunit4SensorDisplayFactor | read-only | mandatory | Factor of sensor value and setpoints, devide actual value with this value, e. g. factor = 10: sensor value = 100, actual value = 10.0 |
| 1.3.6.1.4.1.2606.4.2.6.5.2.1.11 | Columnunit4SensorScaleStart | read-write | mandatory | Value for start value for scaling of 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to… |
| 1.3.6.1.4.1.2606.4.2.6.5.2.1.12 | Columnunit4SensorScaleEnd | read-write | mandatory | Value for end value for scaling of 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to 6… |
| 1.3.6.1.4.1.2606.4.2.6.5.2.1.13 | Columnunit4SensorUnit | read-write | mandatory | Unit for 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to 'A' |
| 1.3.6.1.4.1.2606.4.2.6.5.2.1.14 | Columnunit4SensorInfo | read-only | mandatory | Additional information to the sensor, e. g. Serialnumber, Signal Quality.. |
| 1.3.6.1.4.1.2606.4.2.6.6 | NodecmcTcStatusUnit4Outputs | |||
| 1.3.6.1.4.1.2606.4.2.6.6.1 | ScalarcmcTcUnit4NumberOfOutputs | read-only | mandatory | Number of outputs available on sensor unit 4 |
| 1.3.6.1.4.1.2606.4.2.6.6.2 | TablecmcTcUnit4OutputTable | not-accessible | mandatory | Headline of output table |
| 1.3.6.1.4.1.2606.4.2.6.6.2.1 | RowcmcTcUnit4OutputEntry | not-accessible | mandatory | Entries of output table |
| 1.3.6.1.4.1.2606.4.2.6.6.2.1.1 | Columnunit4OutputIndex | read-only | mandatory | Index for the list of output entries. Its value ranges between 1 and the value of cmcTcUnit4NumberOfOutputs. |
| 1.3.6.1.4.1.2606.4.2.6.6.2.1.2 | Columnunit4OutputType | read-only | mandatory | Type of output which is connected to sensor unit 4 to output[unit4OutputIndex] 1: no output connected 2: output failure 3: value overflow 4: output type 1, doo… |
| 1.3.6.1.4.1.2606.4.2.6.6.2.1.3 | Columnunit4OutputText | read-write | mandatory | Descriptional text for each output (entry in the table) |
| 1.3.6.1.4.1.2606.4.2.6.6.2.1.4 | Columnunit4OutputStatus | read-write | mandatory | Actual status of the output |
| 1.3.6.1.4.1.2606.4.2.6.6.2.1.5 | Columnunit4OutputValue | read-write | mandatory | Value for output |
| 1.3.6.1.4.1.2606.4.2.6.6.2.1.6 | Columnunit4OutputSet | read-write | mandatory | Command for output |
| 1.3.6.1.4.1.2606.4.2.6.6.2.1.7 | Columnunit4OutputConfig | read-write | mandatory | Configuration for output 1: disable remote control (e.g. keypad) 2: enable remote control |
| 1.3.6.1.4.1.2606.4.2.6.6.2.1.8 | Columnunit4OutputDelay | read-write | mandatory | Unsigned Value for delay, after this time the output will fall into the previous state |
| 1.3.6.1.4.1.2606.4.2.6.6.2.1.9 | Columnunit4OutputTimeoutAction | read-write | mandatory | State for output if timeout (RS422) occurs |
| 1.3.6.1.4.1.2606.4.2.6.7 | NodecmcTcStatusUnit4Msg | |||
| 1.3.6.1.4.1.2606.4.2.6.7.1 | ScalarcmcTcUnit4NumberOfMsgs | read-only | mandatory | Number of alarms that can be created with sensor unit 4 |
| 1.3.6.1.4.1.2606.4.2.6.7.2 | TablecmcTcUnit4MsgTable | not-accessible | mandatory | Headline of message table |
| 1.3.6.1.4.1.2606.4.2.6.7.2.1 | RowcmcTcUnit4MsgEntry | not-accessible | mandatory | Entries of message table |
| 1.3.6.1.4.1.2606.4.2.6.7.2.1.1 | Columnunit4MsgIndex | read-only | mandatory | Index for the list of alarm entries. Its value ranges between 1 and the value of cmcTcUnit4NumberOfMsgs. |
| 1.3.6.1.4.1.2606.4.2.6.7.2.1.2 | Columnunit4MsgText | read-write | mandatory | Descriptional text for each message (entry in the table) |
| 1.3.6.1.4.1.2606.4.2.6.7.2.1.3 | Columnunit4MsgStatus | read-only | mandatory | Actual message status 1: not available 2: configuration has changed (sensor new, changed, lost) 3: error 4: OK 5: alarm, e.g. smoke, vibration... 6: warning of… |
| 1.3.6.1.4.1.2606.4.2.6.7.2.1.4 | Columnunit4MsgRelay | read-write | mandatory | Setup of Alarm relay for this alarm 1: no switching of alarm relay 2: switching of alarm relay |
| 1.3.6.1.4.1.2606.4.2.6.7.2.1.5 | Columnunit4MsgBeeper | read-write | mandatory | Setup of Alarm beeper for this alarm 1: no audible alarm 2: audible alarm |
| 1.3.6.1.4.1.2606.4.2.6.7.2.1.6 | Columnunit4MsgTrap1 | read-write | mandatory | Trap receiver 1 activated |
| 1.3.6.1.4.1.2606.4.2.6.7.2.1.7 | Columnunit4MsgTrap2 | read-write | mandatory | Trap receiver 2 activated |
| 1.3.6.1.4.1.2606.4.2.6.7.2.1.8 | Columnunit4MsgTrap3 | read-write | mandatory | Trap receiver 3 activated |
| 1.3.6.1.4.1.2606.4.2.6.7.2.1.9 | Columnunit4MsgTrap4 | read-write | mandatory | Trap receiver 4 and Event Logging activated |
| 1.3.6.1.4.1.2606.4.2.6.7.2.1.10 | Columnunit4MsgQuit | read-write | mandatory | Reset of this alarm 1: auto 2: manual, alarm needs confirmation, e. g. with 'C' key |
| 1.3.6.1.4.1.2606.4.2.6.7.2.1.11 | Columnunit4MsgDelay | read-write | mandatory | Delay of alarm condition |
| 1.3.6.1.4.1.2606.4.2.7 | NodecmcTcStatusExtUnit | |||
| 1.3.6.1.4.1.2606.4.2.7.1 | ScalarcmcTcValuesRelay | read-write | mandatory | Setup of Alarm relay for alarm ext. unit(s) 1: no switching of alarm relay 2: switching of alarm relay |
| 1.3.6.1.4.1.2606.4.2.7.2 | ScalarcmcTcValuesBeeper | read-write | mandatory | Setup of Alarm beeper for alarm ext. unit(s) 1: no audible alarm 2: audible alarm |
| 1.3.6.1.4.1.2606.4.2.7.3 | ScalarcmcTcValuesTrap1 | read-write | mandatory | Trap receiver 1 activated |
| 1.3.6.1.4.1.2606.4.2.7.4 | ScalarcmcTcValuesTrap2 | read-write | mandatory | Trap receiver 2 activated |
| 1.3.6.1.4.1.2606.4.2.7.5 | ScalarcmcTcValuesTrap3 | read-write | mandatory | Trap receiver 3 activated |
| 1.3.6.1.4.1.2606.4.2.7.6 | ScalarcmcTcValuesTrap4 | read-write | mandatory | Trap receiver 4 and Event Logging activated |
| 1.3.6.1.4.1.2606.4.2.7.7 | ScalarcmcTcNumberOfValues | read-only | mandatory | Number of values availabel on extension units connected to the CMC |
| 1.3.6.1.4.1.2606.4.2.7.8 | TablecmcTcValuesTable | not-accessible | mandatory | Headline of values-table |
| 1.3.6.1.4.1.2606.4.2.7.8.1 | RowcmcTcValuesEntry | not-accessible | mandatory | Entries of values-table |
| 1.3.6.1.4.1.2606.4.2.7.8.1.1 | ColumnvaluesIndex | read-only | mandatory | Index for the list of value entries. Its value ranges between 1 and the value of cmcTcNumberOfValues. |
| 1.3.6.1.4.1.2606.4.2.7.8.1.2 | ColumnvaluesText | read-write | mandatory | Descriptional text for each value (entry in the table) of the extension card |
| 1.3.6.1.4.1.2606.4.2.7.8.1.3 | ColumnvaluesStatus | read-only | mandatory | Actual status of the value of the extension card |
| 1.3.6.1.4.1.2606.4.2.7.8.1.4 | ColumnvaluesValue | read-only | mandatory | Value of sensor |
| 1.3.6.1.4.1.2606.4.2.7.8.1.5 | ColumnvaluesSetHigh | read-write | mandatory | Value for high setpoint of sensor |
| 1.3.6.1.4.1.2606.4.2.7.8.1.6 | ColumnvaluesSetLow | read-write | mandatory | Value for low setpoint of sensor |
| 1.3.6.1.4.1.2606.4.2.7.8.1.7 | ColumnvaluesHysteresis | read-write | mandatory | % -Value for hysteresis for High and Low setpoints, input in % from actual setpoint |
| 1.3.6.1.4.1.2606.4.3 | NodealarmSensorUnit3 | Alarm of sensor unit 3 | ||
| 1.3.6.1.4.1.2606.4.3 | NodecmcTcSetup | |||
| 1.3.6.1.4.1.2606.4.3.1 | NodecmcTcSetupGeneral | |||
| 1.3.6.1.4.1.2606.4.3.1.1 | ScalarcmcTcSetTempUnit | read-write | mandatory | Unit of all temperature values and setpoints, Celsius or Fahrenheit |
| 1.3.6.1.4.1.2606.4.3.1.2 | ScalarcmcTcSetBeeper | read-write | mandatory | Audible alarm in CMC-TC unit: (2): beeper is on (1): beeper is off (general) |
| 1.3.6.1.4.1.2606.4.3.1.3 | ScalarcmcTcQuitRelay | read-write | mandatory | Enable or disable acknowledging currently active alarm relay (with 'C' on CMC-TC). |
| 1.3.6.1.4.1.2606.4.3.1.4 | ScalarcmcTcLogicRelay | read-write | mandatory | Logic of alarm relay: (1) Relay will pick up in case of an alarm (2) Relay will release in case of an alarm (3) Relay off (general) |
| 1.3.6.1.4.1.2606.4.3.1.5 | ScalarcmcTcWebAccess | read-write | mandatory | Web access via HTTP: (1) view only (2) full Access, read and set (3) Web disabled (general) |
| 1.3.6.1.4.1.2606.4.3.1.6 | ScalarcmcTcSetupDate | read-write | mandatory | actual Date in format DD.MM.YYYY |
| 1.3.6.1.4.1.2606.4.3.1.7 | ScalarcmcTcSetupTime | read-write | mandatory | actual Time in format HH:MM:SS, HH (0-23), MM (0-59), SS (0-59) |
| 1.3.6.1.4.1.2606.4.3.1.8 | NodecmcTcTimerTable1 | |||
| 1.3.6.1.4.1.2606.4.3.1.8.1 | ScalarcmcTcTimerNumber | read-only | mandatory | Number of value-table entries=number of outlets available on this unit |
| 1.3.6.1.4.1.2606.4.3.1.8.2 | TablecmcTcTimerTable | not-accessible | mandatory | Headline of status-table |
| 1.3.6.1.4.1.2606.4.3.1.8.2.1 | RowcmcTcTimerEntry | not-accessible | mandatory | Entries of timer-table |
| 1.3.6.1.4.1.2606.4.3.1.8.2.1.1 | ColumncmcTcTimerIndex | read-only | mandatory | Index for the list of timer entries. Its value ranges between 1 and the value of cmcTcTimerNumber. |
| 1.3.6.1.4.1.2606.4.3.1.8.2.1.2 | ColumncmcTcTimerStatus | read-only | mandatory | Actual status of the timer |
| 1.3.6.1.4.1.2606.4.3.1.8.2.1.3 | ColumncmcTcTimerDayOfWeek | read-write | mandatory | Selection of day of week for timer to switch |
| 1.3.6.1.4.1.2606.4.3.1.8.2.1.4 | ColumncmcTcTimeOn | read-write | mandatory | Time to switch on current function, Format: HH:MM |
| 1.3.6.1.4.1.2606.4.3.1.8.2.1.5 | ColumncmcTcTimeOff | read-write | mandatory | Time to switch off current function, Format: HH:MM |
| 1.3.6.1.4.1.2606.4.3.1.8.2.1.6 | ColumncmcTcTimeControl | read-write | mandatory | Control via RTC |
| 1.3.6.1.4.1.2606.4.3.1.8.2.1.7 | ColumncmcTcTimerFunction | read-write | mandatory | Function which is controlled via timer 1: unlock via keypad 1 on unit 1 or remote input lock 1 is disabled 2: unlock via keypad 2 on unit 1 or remote input loc… |
| 1.3.6.1.4.1.2606.4.4 | NodealarmSensorUnit4 | Alarm of sensor unit 4 | ||
| 1.3.6.1.4.1.2606.4.4 | NodecmcTcTrapControl | |||
| 1.3.6.1.4.1.2606.4.4.7 | NodecmcTcTraps | |||
| 1.3.6.1.4.1.2606.4.4.7.1 | ScalarcmcTcTraptableNumber | read-only | mandatory | Number of trapTable entries. The number of trap-receiver |
| 1.3.6.1.4.1.2606.4.4.7.2 | TablecmcTcTrapTableTable | not-accessible | mandatory | A list of trap-receiver entries |
| 1.3.6.1.4.1.2606.4.4.7.2.1 | RowcmcTcTrapTableEntry | not-accessible | mandatory | Entries of trapTable |
| 1.3.6.1.4.1.2606.4.4.7.2.1.1 | ColumntrapIndex | read-only | mandatory | Index for the trap-receiver-table. Its value ranges between 1 and the value of traptableNumber |
| 1.3.6.1.4.1.2606.4.4.7.2.1.2 | ColumntrapStatus | read-write | mandatory | Enable or disable trap receiver |
| 1.3.6.1.4.1.2606.4.4.7.2.1.3 | ColumntrapIPaddress | read-write | mandatory | IP-address of trap-receiver |
| 1.3.6.1.4.1.2606.4.5 | NodealarmUnit1 | Alarm of unit 1 | ||
| 1.3.6.1.4.1.2606.4.5 | NodecmcTcControl | |||
| 1.3.6.1.4.1.2606.4.5.1 | ScalarcmcTcQuitUnit | read-write | mandatory | Command to quit (acknowledge) alarms of CMC-TC unit. Setting to 'quit' (2) will have same result as pressing 'C' on Units. Variable is automatically set back t… |
| 1.3.6.1.4.1.2606.4.6 | NodealarmUnit2 | Alarm of unit 2 | ||
| 1.3.6.1.4.1.2606.4.7 | NodealarmUnit3 | Alarm of unit 3 | ||
| 1.3.6.1.4.1.2606.4.8 | NodealarmUnit4 | Alarm of unit 4 | ||
| 1.3.6.1.4.1.2606.4.9 | NodealarmValues | Alarm of values measured by external card | ||
| 1.3.6.1.4.1.2606.4.10 | NodeconfigChanged | The configuration of the cmc has changed, this trap is send if new setup is saved. Configuration can be changed by Terminal, Telnet, Web or SNMP *** NOT IMPLEM… |