SA-RG-MIB
242 objects
Controls the behavior of router/wireless functions. Can be part of CM configuration file.
Imported Objects
| IF-MIB | ifIndex |
| INET-ADDRESS-MIB | InetAddress InetAddressIPv6 InetAddressType InetPortNumber |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-SMI | enterprises Integer32 IpAddress MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DateAndTime DisplayString MacAddress PhysAddress RowStatus TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.1429 | Nodesa | |||
| 1.3.6.1.4.1.1429.79 | NodesaModules | |||
| 1.3.6.1.4.1.1429.79.2 | IdentitysaRg | Controls the behavior of router/wireless functions. Can be part of CM configuration file. | ||
| 1.3.6.1.4.1.1429.79.2.1 | NodesaRgDevice | |||
| 1.3.6.1.4.1.1429.79.2.1.1 | NodesaRgDeviceBase | |||
| 1.3.6.1.4.1.1429.79.2.1.1.1 | ScalarsaRgDeviceMode | read-write | current | Defines the mode of operation for the device. This parameter is stored in non-vol and is multiSsid(1) by default. Setting this object via SNMP will cause the u… |
| 1.3.6.1.4.1.1429.79.2.1.1.2 | ScalarsaRgDeviceResetDefaultEnable | read-write | current | This object controls the reset to factory default functionality of the gateway. This prevents the local user from using the reset switch to gain access to the … |
| 1.3.6.1.4.1.1429.79.2.1.1.4 | ScalarsaRgDeviceRemoteWebAccessPort | read-write | current | Defines what port to use for the WAN IP address of the gateway to be able to access RG web pages. This value is to be stored in non-vol and will persist across… |
| 1.3.6.1.4.1.1429.79.2.1.1.6 | ScalarsaRgDeviceLanLanIsolation | read-write | current | This MIB is only available in D3.0 products. This MIB does not take effect if the modem is in VLAN mode i.e if saRgIpMgmtLanMode.32=vlan(5). Lan-Lan Isolation … |
| 1.3.6.1.4.1.1429.79.2.1.1.7 | ScalarsaRgDeviceLanWlanIsolation | read-write | current | This MIB is only available in D3.0 products. This MIB does not take effect if the modem is in VLAN mode i.e if saRgIpMgmtLanMode.32=vlan(5). Lan-Wlan Isolation… |
| 1.3.6.1.4.1.1429.79.2.1.1.8 | ScalarsaRgDeviceIpv6Trans | read-only | current | This MIB will control which IPv6 transition technology is enabled on the device. After setting this MIB to disable in the config file, IPv4 traffic will pass n… |
| 1.3.6.1.4.1.1429.79.2.1.1.9 | ScalarsaRgDeviceIpv6Passthrough | read-write | current | This MIB controls IPv6 passthrough on the RG and is applicable in bridge and router modes. When disabled the RG will function without any IPv6 passthrough When… |
| 1.3.6.1.4.1.1429.79.2.1.1.1002 | ScalarsaRgDeviceFactoryReset | read-write | current | Set routerAndWifi(1) to restore default settings of both the router and wifi. Set routerOnly(2) to restore default settings of the router. Set wifi(3) to resto… |
| 1.3.6.1.4.1.1429.79.2.1.5 | NodesaRgDeviceTimeSetup | |||
| 1.3.6.1.4.1.1429.79.2.1.5.1 | ScalarsaRgDeviceTimeSetupNtpEnabled | read-write | current | Stored in non-vol, disabled after factory reset. |
| 1.3.6.1.4.1.1429.79.2.1.5.2 | TablesaRgDeviceTimeSetupNtpServerTable | not-accessible | current | Up to 3 NTP servers are supported. This table is stored in non-vol. Default entries after factory reset are: 1: time.nist.gov 2: nist.aol-ca.truetime.com 3: ni… |
| 1.3.6.1.4.1.1429.79.2.1.5.2.1 | RowsaRgDeviceTimeSetupNtpServerEntry | not-accessible | current | |
| 1.3.6.1.4.1.1429.79.2.1.5.2.1.1 | ColumnsaRgDeviceTimeSetupNtpServerIndex | not-accessible | current | The index |
| 1.3.6.1.4.1.1429.79.2.1.5.2.1.2 | ColumnsaRgDeviceTimeSetupNtpServerAddress | read-write | current | IP address or FQDN of the NTP server. |
| 1.3.6.1.4.1.1429.79.2.1.5.3 | ScalarsaRgDeviceTimeSetupZone | read-write | current | Time zone for the gateway. Stored in non-vol, gmtZeroDublinEdinburghLisbonLondon(26) after factory reset. |
| 1.3.6.1.4.1.1429.79.2.1.5.4 | ScalarsaRgDeviceTimeSetupDst | read-write | current | Daylight saving time. If set to 0, DST is disabled Stored in non-vol, 0 after factory reset. |
| 1.3.6.1.4.1.1429.79.2.1.7 | NodesaRgDeviceIanaContent | |||
| 1.3.6.1.4.1.1429.79.2.1.7.1 | ScalarsaRgDeviceIanaIAID | read-only | current | Returns the IAID value embedded in the IA_NA for the eRouter's DHCPv6 lease. |
| 1.3.6.1.4.1.1429.79.2.1.7.2 | ScalarsaRgDeviceIanaT1 | read-only | current | Returns the T1 value embedded in the IA_NA for the eRouter's DHCPv6 lease. |
| 1.3.6.1.4.1.1429.79.2.1.7.3 | ScalarsaRgDeviceIanaT2 | read-only | current | Returns the T2 value embedded in the IA_NA for the eRouter's DHCPv6 lease. |
| 1.3.6.1.4.1.1429.79.2.1.7.4 | TablesaRgDeviceIanaTable | not-accessible | current | Table of IA Address entries associated with IA_NA for the eRouter's DHCPv6 lease. |
| 1.3.6.1.4.1.1429.79.2.1.7.4.1 | RowsaRgDeviceIanaEntry | not-accessible | current | Table of IA Address entries associated with IA_NA for the eRouter's DHCPv6 lease. |
| 1.3.6.1.4.1.1429.79.2.1.7.4.1.1 | ColumnsaRgDeviceIanaIndex | not-accessible | current | The index |
| 1.3.6.1.4.1.1429.79.2.1.7.4.1.2 | ColumnsaRgDeviceIanaValue | read-only | current | IPv6 address provided to the eRouter WAN interface via DHCPv6. |
| 1.3.6.1.4.1.1429.79.2.1.7.4.1.3 | ColumnsaRgDeviceIanaPreferredLifetime | read-only | current | Preferred Lifetime setting for an IPv6 address assigned to the eRouter. |
| 1.3.6.1.4.1.1429.79.2.1.7.4.1.4 | ColumnsaRgDeviceIanaValidLifetime | read-only | current | Valid Lifetime setting for an IPv6 address assigned to the eRouter. |
| 1.3.6.1.4.1.1429.79.2.1.8 | NodesaRgDeviceIapdContent | |||
| 1.3.6.1.4.1.1429.79.2.1.8.1 | ScalarsaRgDeviceIapdIAID | read-only | current | Returns the IAID value embedded in the IA_PD for the eRouter's DHCPv6 lease. |
| 1.3.6.1.4.1.1429.79.2.1.8.2 | ScalarsaRgDeviceIapdT1 | read-only | current | Returns the T1 value embedded in the IA_PD for the eRouter's DHCPv6 lease. |
| 1.3.6.1.4.1.1429.79.2.1.8.3 | ScalarsaRgDeviceIapdT2 | read-only | current | Returns the T2 value embedded in the IA_PD for the eRouter's DHCPv6 lease. |
| 1.3.6.1.4.1.1429.79.2.1.8.4 | TablesaRgDeviceIapdTable | not-accessible | current | Table of IA Prefix entries associated with IA_PD for the eRouter's DHCPv6 lease. |
| 1.3.6.1.4.1.1429.79.2.1.8.4.1 | RowsaRgDeviceIapdEntry | not-accessible | current | Table of IA Address entries associated with IA_PD for the eRouter's DHCPv6 lease. |
| 1.3.6.1.4.1.1429.79.2.1.8.4.1.1 | ColumnsaRgDeviceIapdIndex | not-accessible | current | The index |
| 1.3.6.1.4.1.1429.79.2.1.8.4.1.2 | ColumnsaRgDeviceIapdPreferredLifetime | read-only | current | Preferred Lifetime setting for an IPv6 address assigned to the eRouter. |
| 1.3.6.1.4.1.1429.79.2.1.8.4.1.3 | ColumnsaRgDeviceIapdValidLifetime | read-only | current | Valid Lifetime setting for an IPv6 address assigned to the eRouter. |
| 1.3.6.1.4.1.1429.79.2.1.8.4.1.4 | ColumnsaRgDeviceIapdPrefixLength | read-only | current | Length (in bits) for this prefix. |
| 1.3.6.1.4.1.1429.79.2.1.8.4.1.5 | ColumnsaRgDeviceIapdPrefixValue | read-only | current | Prefix address specified in the IA_PD. |
| 1.3.6.1.4.1.1429.79.2.2 | NodesaRgDot11 | |||
| 1.3.6.1.4.1.1429.79.2.2.1 | NodesaRgDot11MgmtBase | |||
| 1.3.6.1.4.1.1429.79.2.2.1.20 | ScalarsaRgDot11OnOffPushButtonTime | read-write | current | Specifies how long to press WPS button to enable or disable the WiFi interface (primary SSID). When set to 11, the feature is disabled. Stored in non-vol, 11 a… |
| 1.3.6.1.4.1.1429.79.2.2.2 | NodesaRgDot11Bss | |||
| 1.3.6.1.4.1.1429.79.2.2.2.1 | TablesaRgDot11BssTable | not-accessible | current | BSS table |
| 1.3.6.1.4.1.1429.79.2.2.2.1.1 | RowsaRgDot11BssEntry | not-accessible | current | A row in the table which represents parameters for SSID. |
| 1.3.6.1.4.1.1429.79.2.2.2.1.1.1 | ColumnsaRgDot11BssId | read-only | current | Returns the BSSID |
| 1.3.6.1.4.1.1429.79.2.2.2.1.1.2 | ColumnsaRgDot11BssEnable | read-write | current | Controls the BSS state. When set to enableOnline(3), the SSID is enabled only when the cable modem is online. When the modem changes state to offline, the AP w… |
| 1.3.6.1.4.1.1429.79.2.2.2.1.1.3 | ColumnsaRgDot11BssSsid | read-write | current | Controls and reflects the service set identifier. The value of primary BSS is stored in non-vol and is empty after factory reset. If other BSS's SSID name is n… |
| 1.3.6.1.4.1.1429.79.2.2.2.1.1.4 | ColumnsaRgDot11BssSecurityMode | read-write | current | Secrity for BSS. Beacause WPA2 is backwords compatible with WPA, setting this object to wpaWpa2Psk(7) is allowed and has the same effect as setting to wpa2Psk(… |
| 1.3.6.1.4.1.1429.79.2.2.2.1.1.5 | ColumnsaRgDot11BssClosedNetwork | read-write | current | Controls whether the device will operate in closed network mode. If set to true(1), then the network mode is closed and the SSID will not be broadcast in beaco… |
| 1.3.6.1.4.1.1429.79.2.2.2.1.1.6 | ColumnsaRgDot11BssAccessMode | read-write | current | Controls what stations will be given access to the device. If set to allowAny(0), then any station will be allowed to connect. If set to allowList(1), then onl… |
| 1.3.6.1.4.1.1429.79.2.2.2.1.1.11 | ColumnsaRgDot11BssMaxNumSta | read-write | current | This object defines the maximum number of STAs that can connect to this SSID. Note that the maximum number of STA accross all SSIDs in the AP is 128. Default v… |
| 1.3.6.1.4.1.1429.79.2.2.2.1.1.13 | ColumnsaRgDot11BssUserStatus | read-only | current | Provides the BSS Id Web UI or Wireless ON/OFF (if exist) status that is set by the user. If the user can press the Wireless ON/OFF (if exist) button and its st… |
| 1.3.6.1.4.1.1429.79.2.2.2.1.1.15 | ColumnsaRgDot11BssApIsolation | read-write | current | This MIB is only available in D3.0 products. AP Isolation (Access Point Isolation) allows you to isloate traffic between CPEs on the same Wifi SSID. This allow… |
| 1.3.6.1.4.1.1429.79.2.2.2.1.1.16 | ColumnsaRgDot11BssSecSsidTrafficPriority | read-only | current | This MIB is only available in D3.0 products and applicable for secondary SSID in hotspot environment. When disabled, all the traffic to the secondary SSID in q… |
| 1.3.6.1.4.1.1429.79.2.2.2.1.1.17 | ColumnsaRgDot11BssRejectPriSsidSta | read-only | current | This MIB is only available in D3.0 products and applicable for secondary SSID in hotspot environment. By default, a private SSID STA can associate to hotspot S… |
| 1.3.6.1.4.1.1429.79.2.2.2.3 | NodesaRgDot11BssPrimary | |||
| 1.3.6.1.4.1.1429.79.2.2.2.3.1 | ScalarsaRgDot11BssPrimarySsidType | read-write | current | This object specifies the type of SSID used. mac6char(1): If saRgDot11BssSsid.32 is empty, the SSID is the last 3 bytes of DOCSIS MAC address, displayed as 6 l… |
| 1.3.6.1.4.1.1429.79.2.2.2.3.2 | ScalarsaRgDot11BssPrimarySsidPrefix | read-write | current | The prefix for primary SSID, if saRgDot11BssSsid.32 is empty and saRgDot11BssPrimarySsidType is set to mac6char-prefix(2). Stored in non-vol. Empty after facto… |
| 1.3.6.1.4.1.1429.79.2.2.3 | NodesaRgDot11Privacy | |||
| 1.3.6.1.4.1.1429.79.2.2.3.1 | TablesaRgDot11WpaTable | not-accessible | current | WPA table |
| 1.3.6.1.4.1.1429.79.2.2.3.1.1 | RowsaRgDot11WpaEntry | not-accessible | current | A row in the table which represents WPA parameters for BSS. |
| 1.3.6.1.4.1.1429.79.2.2.3.1.1.1 | ColumnsaRgDot11WpaAlgorithm | read-write | current | The value of tkip(0) is not allowed when security is WPA2. The value for primary BSS is stored in non-vol and tkipPlusAes(2) after factory reset. The default v… |
| 1.3.6.1.4.1.1429.79.2.2.3.1.1.2 | ColumnsaRgDot11WpaPreSharedKey | read-write | current | Sets the WPA Pre-Shared Key (PSK). This value MUST be either a 64-digit hexadecimal number, OR a 8 to 63 character ASCII string. The value for primary BSS is s… |
| 1.3.6.1.4.1.1429.79.2.2.3.1.1.3 | ColumnsaRgDot11WpaGroupRekeyInterval | read-write | current | Sets the WPA Group Rekey Interval in seconds. Set to zero to disable periodic rekeying. The value for primary BSS is stored in non-vol and is 3600 after factor… |
| 1.3.6.1.4.1.1429.79.2.2.3.2 | TablesaRgDot11RadiusTable | not-accessible | current | WPA table |
| 1.3.6.1.4.1.1429.79.2.2.3.2.1 | RowsaRgDot11RadiusEntry | not-accessible | current | A row in the table which represents WPA parameters for BSS. |
| 1.3.6.1.4.1.1429.79.2.2.3.2.1.1 | ColumnsaRgDot11RadiusAddressType | read-write | current | Type of RADIUS server IP address. |
| 1.3.6.1.4.1.1429.79.2.2.3.2.1.2 | ColumnsaRgDot11RadiusAddress | read-write | current | Sets RADIUS server IP address. The value for primary BSS is stored in non-vol and is 0.0.0.0 after factory reset. The default value for other BSSs is 0.0.0.0. |
| 1.3.6.1.4.1.1429.79.2.2.3.2.1.3 | ColumnsaRgDot11RadiusPort | read-write | current | Sets the UDP port used to communicate with the RADIUS server. The value for primary BSS is stored in non-vol and is 1645 after factory reset. The default value… |
| 1.3.6.1.4.1.1429.79.2.2.3.2.1.4 | ColumnsaRgDot11RadiusKey | read-write | current | Sets or displays the RADIUS key. The value for primary BSS is stored in non-vol and is null after factory reset. The default value for other BSSs is null. This… |
| 1.3.6.1.4.1.1429.79.2.2.3.2.1.5 | ColumnsaRgDot11RadiusReAuthInterval | read-write | current | Sets the RADIUS Rekey Interval in seconds. Set to zero to disable periodic rekeying. The value for primary BSS is stored in non-vol and is 3600 after factory r… |
| 1.3.6.1.4.1.1429.79.2.2.3.3 | TablesaRgDot11WepTable | not-accessible | current | WEP table |
| 1.3.6.1.4.1.1429.79.2.2.3.3.1 | RowsaRgDot11WepEntry | not-accessible | current | A row in the table which represents WPA parameters for BSS. |
| 1.3.6.1.4.1.1429.79.2.2.3.3.1.1 | ColumnsaRgDot11WepDefaultKey | read-write | current | Controls and reflects the default key which will be used when 64 or 128 bit encryption is enabled. Indicates the entry from the saRgDot1164BitKeyTable if saRgD… |
| 1.3.6.1.4.1.1429.79.2.2.3.3.1.2 | ColumnsaRgDot11WepEncryptionMode | read-write | current | The value for primary BSS is stored in non-vol and is wep128(1) after factory reset. The default value for other BSSs is wep128. |
| 1.3.6.1.4.1.1429.79.2.2.3.3.1.3 | ColumnsaRgDot11WepPassPhrase | read-write | current | Controls and reflects the WEP pass phrase. The value for primary BSS is stored in non-vol and is null after factory reset. The default value for other BSSs is … |
| 1.3.6.1.4.1.1429.79.2.2.3.4 | TablesaRgDot11Wep64BitKeyTable | not-accessible | current | A table of 40 bit key values used when saRgDot11WepEncryptionMode is set to wep64(0). |
| 1.3.6.1.4.1.1429.79.2.2.3.4.1 | RowsaRgDot11Wep64BitKeyEntry | not-accessible | current | A row in the table which represents a single 64 bit key. |
| 1.3.6.1.4.1.1429.79.2.2.3.4.1.1 | ColumnsaRgDot11Wep64BitKeyIndex | not-accessible | current | Identifies the instance of this table row. |
| 1.3.6.1.4.1.1429.79.2.2.3.4.1.2 | ColumnsaRgDot11Wep64BitKeyValue | read-write | current | A 40 bit key to be used when saRgDot11WepEncryptionMode is set to wep64(1). The value for primary BSS is stored in non-vol and is all 1's after factory reset. … |
| 1.3.6.1.4.1.1429.79.2.2.3.5 | TablesaRgDot11Wep128BitKeyTable | not-accessible | current | A table of 104 bit key values used when saRgDot11WepEncryptionMode is set to wep128(1). |
| 1.3.6.1.4.1.1429.79.2.2.3.5.1 | RowsaRgDot11Wep128BitKeyEntry | not-accessible | current | A row in the table which represents a single 128 bit key. |
| 1.3.6.1.4.1.1429.79.2.2.3.5.1.1 | ColumnsaRgDot11Wep128BitKeyIndex | not-accessible | current | Identifies the instance of this table row. |
| 1.3.6.1.4.1.1429.79.2.2.3.5.1.2 | ColumnsaRgDot11Wep128BitKeyValue | read-write | current | A 104 bit key to be used when saRgDot11WepEncryptionMode is set to wep128(2). The value for primary BSS is stored in non-vol and is all 1's. The default value … |
| 1.3.6.1.4.1.1429.79.2.2.3.6 | NodesaRgDot11PrivacyWps | |||
| 1.3.6.1.4.1.1429.79.2.2.3.6.1 | ScalarsaRgDot11PrivacyWpsPushButtonTime | read-write | current | Specifies how long to press WPS button to start the WPS procedure. 0 means disable WPS. Stored in non-vol, 1 after factory reset. |
| 1.3.6.1.4.1.1429.79.2.2.4 | NodesaRgDot11Client | |||
| 1.3.6.1.4.1.1429.79.2.2.4.2 | TablesaRgDot11ClientTable | not-accessible | current | A table of wireless clients that are associated with the BSS. |
| 1.3.6.1.4.1.1429.79.2.2.4.2.1 | RowsaRgDot11ClientEntry | not-accessible | current | A row in the table that specifies a single station MAC address. |
| 1.3.6.1.4.1.1429.79.2.2.4.2.1.1 | ColumnsaRgDot11ClientIndex | not-accessible | current | Indicates the instance of this table row. |
| 1.3.6.1.4.1.1429.79.2.2.4.2.1.2 | ColumnsaRgDot11ClientStation | read-only | current | A MAC address of a client associated with the BSS. |
| 1.3.6.1.4.1.1429.79.2.2.6 | NodesaRgDot11ExtMgmt | |||
| 1.3.6.1.4.1.1429.79.2.2.6.1 | TablesaRgDot11ExtMgmtTable | not-accessible | current | Multiple Radio Configuration Table |
| 1.3.6.1.4.1.1429.79.2.2.6.1.1 | RowsaRgDot11ExtMgmtEntry | not-accessible | current | A row in the table which represents parameters for a Radio. Index 32 should be set for Radio 0 Index 112 should be set for Radio 1 |
| 1.3.6.1.4.1.1429.79.2.2.6.1.1.15 | ColumnsaRgDot11ExtMbssUserControl | read-write | current | Sets the number of user controlled Wifi networks via web pages. 1: The user has control over the primary wireless network only. No guest network page is displa… |
| 1.3.6.1.4.1.1429.79.2.2.6.1.1.16 | ColumnsaRgDot11ExtMbssUseNonvol | read-write | current | Allows to save additional BSS parameters to non-vol if set to true. Primary BSS parameters are ALWAYS stored in non-vol. This object value is stored in non-vol… |
| 1.3.6.1.4.1.1429.79.2.2.6.1.1.17 | ColumnsaRgDot11ExtMbssAdminControl | read-write | current | Sets the number of admin controlled Wifi networks via web pages. 1: The admin has control over the primary wireless network only. No guest network page is disp… |
| 1.3.6.1.4.1.1429.79.2.2.6.1.1.18 | ColumnsaRgDot11ExtActualChannel | read-only | current | Reports the current channel number that wireless is on. The value of 0 means wireless is disabled. |
| 1.3.6.1.4.1.1429.79.2.2.1001 | ScalarsaRgDot11ApplySettings | read-write | current | If set to true(1), then all the settings (MIB values) from this MIB tree will be applied to run time configuration, modifying previous RG operation with the ne… |
| 1.3.6.1.4.1.1429.79.2.3 | NodesaRgIpMgmt | |||
| 1.3.6.1.4.1.1429.79.2.3.2 | TablesaRgIpMgmtLanTable | not-accessible | current | Networks on the LAN side. Primary BSS stored in non-vol. |
| 1.3.6.1.4.1.1429.79.2.3.2.1 | RowsaRgIpMgmtLanEntry | not-accessible | current | List of networks on the LAN side. |
| 1.3.6.1.4.1.1429.79.2.3.2.1.1 | ColumnsaRgIpMgmtLanMode | read-write | current | Defines the mode of operation for the device. Setting this object via SNMP for the primary BSS will cause the unit to reboot. Setting this object via SNMP for … |
| 1.3.6.1.4.1.1429.79.2.3.2.1.3 | ColumnsaRgIpMgmtLanNetwork | read-write | current | The LAN-Trans network number. Default for primary BSS is 192.168.0.0 Default for other BSSs is 192.168.ifIndex.0 |
| 1.3.6.1.4.1.1429.79.2.3.2.1.4 | ColumnsaRgIpMgmtLanNetworksAllow | read-write | current | Allows the user via the internal Web GUI (Lan Setup page to input an IPv4 public or private Local IP address other than a class C Private address (the default … |
| 1.3.6.1.4.1.1429.79.2.3.2.1.5 | ColumnsaRgIpMgmtLanSubnetMask | read-write | current | The device MUST provide the value of this MIB object in the Option 1 (Subnet Mask) of DHCP OFFER and ACK messages sent to a LAN IP Device. |
| 1.3.6.1.4.1.1429.79.2.3.2.1.7 | ColumnsaRgIpMgmtLanGateway | read-write | current | The type of this address is specified by saRgIpMgmtLanNetwokRouterType. The PS MUST provide the value of this MIB object in the Option 3 (Router IP address) of… |
| 1.3.6.1.4.1.1429.79.2.3.2.1.8 | ColumnsaRgIpMgmtLanDhcpServer | read-write | current | The value for primary BSS is stored in non-vol. The default value for other BSSs is: Enabled by default if interface is in router mode. Always disabled if inte… |
| 1.3.6.1.4.1.1429.79.2.3.2.1.9 | ColumnsaRgIpMgmtLanNapt | read-write | current | The value for primary BSS is stored in non-vol. The default value for other BSSs is: Enabled by default if interface is in router mode. Always disabled if inte… |
| 1.3.6.1.4.1.1429.79.2.3.2.1.10 | ColumnsaRgIpMgmtLanTypeOfService | read-write | current | Definition of the TOS bits for the Network. This object does not apply to primary BSS. |
| 1.3.6.1.4.1.1429.79.2.3.2.1.11 | ColumnsaRgIpMgmtLanDhcp125Option | read-write | current | This option controls if the RG adds a Cisco specific suboption (number 17) to DHCP DISCOVER and REQUEST from the clients that are bridged on the BSS: 0: do not… |
| 1.3.6.1.4.1.1429.79.2.3.2.1.13 | ColumnsaRgIpMgmtLanUpnp | read-write | current | Enable/Disable the UPnP agent. The value is stored in non-vol and is disabled after factory default for the primary SSID. The UPnP agents for additional networ… |
| 1.3.6.1.4.1.1429.79.2.3.2.1.14 | ColumnsaRgIpMgmtLanDhcpOption43 | read-write | current | If option 60 is set from the CPE then return this value in option 43 of the DHCP Reply. If this value is null then do not reply with option 43 (default is null… |
| 1.3.6.1.4.1.1429.79.2.3.3 | TablesaRgIpMgmtLanDhcpServerTable | not-accessible | current | Networks on the LAN side. Stored in non-vol. .10-.128 for primary BSS after factory reset. |
| 1.3.6.1.4.1.1429.79.2.3.3.1 | RowsaRgIpMgmtLanDhcpServerEntry | not-accessible | current | List of networks on the LAN side. |
| 1.3.6.1.4.1.1429.79.2.3.3.1.2 | ColumnsaRgIpMgmtLanDhcpServerPoolStart | read-write | current | The start of range LAN Trans IP Addresses. The type of this address is specified by saRgIpMgmtLanDhcpServerPoolStartType. Default value depends on IP network a… |
| 1.3.6.1.4.1.1429.79.2.3.3.1.4 | ColumnsaRgIpMgmtLanDhcpServerPoolEnd | read-write | current | The end of range for LAN-Trans IP Addresses. The type of this address is specified by saRgIpMgmtLanDhcpServerPoolEndType. Default value depends on IP network a… |
| 1.3.6.1.4.1.1429.79.2.3.3.1.5 | ColumnsaRgIpMgmtLanDhcpServerLeaseTime | read-write | current | The PS MUST provide the value of this MIB object in the Option 51 (IP Address lease time) of the DHCP OFFER and ACK messages sent to the LAN IP Device. |
| 1.3.6.1.4.1.1429.79.2.3.4 | TablesaRgIpMgmtLanAddrTable | not-accessible | current | IP addresses of devices served by DHCP servers. |
| 1.3.6.1.4.1.1429.79.2.3.4.1 | RowsaRgIpMgmtLanAddrEntry | not-accessible | current | List of general parameters pertaining to LAN-Trans IP address reservations and leases. |
| 1.3.6.1.4.1.1429.79.2.3.4.1.1 | ColumnsaRgIpMgmtLanAddrIndex | not-accessible | current | The index of the the LAN IP Device in the LAN-Trans Realm. |
| 1.3.6.1.4.1.1429.79.2.3.4.1.3 | ColumnsaRgIpMgmtLanAddrIp | read-only | current | |
| 1.3.6.1.4.1.1429.79.2.3.4.1.4 | ColumnsaRgIpMgmtLanAddrPhysAddr | read-only | current | The client's (i.e., LAN IP Device's) hardware address as indicated in the chaddr field of its DHCP REQUEST message. |
| 1.3.6.1.4.1.1429.79.2.3.4.1.5 | ColumnsaRgIpMgmtLanAddrLeaseCreateTime | read-only | current | This is the date and time when the LAN IP lease was created (if it has not yet been renewed) or last renewed. |
| 1.3.6.1.4.1.1429.79.2.3.4.1.6 | ColumnsaRgIpMgmtLanAddrLeaseExpireTime | read-only | current | This is the date and time when the LAN IP address lease expired or will expire. |
| 1.3.6.1.4.1.1429.79.2.3.4.1.7 | ColumnsaRgIpMgmtLanAddrHostName | read-only | current | This is the Host Name of the LAN IP address, based on DCHP option 12. |
| 1.3.6.1.4.1.1429.79.2.3.4.1.8 | ColumnsaRgIpMgmtLanAddrClientId | read-only | current | This is the Client Class Identifier, based on DHCP option 60. |
| 1.3.6.1.4.1.1429.79.2.3.4.1.9 | ColumnsaRgIpMgmtLanAddrInterface | read-only | current | This will show the associated interface (LAN, WiFi or MoCA) of the connected CPE. |
| 1.3.6.1.4.1.1429.79.2.3.5 | TablesaRgIpMgmtDnsServerTable | not-accessible | current | This table contains the IP addresses of cable network and Internet DNS servers, in the order of preference in which the PS's CNP will query them, when it canno… |
| 1.3.6.1.4.1.1429.79.2.3.5.1 | RowsaRgIpMgmtDnsServerEntry | not-accessible | current | List of cable network and Internet DNS servers. |
| 1.3.6.1.4.1.1429.79.2.3.5.1.3 | ColumnsaRgIpMgmtDnsServerIp | read-write | current | This parameter indicates the IP address of a WAN DNS server. |
| 1.3.6.1.4.1.1429.79.2.3.6 | TablesaRgIpMgmtDhcpFixedIpTable | not-accessible | current | Fixed IP address assignments for DHCP server. Table does not return any row if DHCP disabled. The value for primary BSS is stored in non-vol. |
| 1.3.6.1.4.1.1429.79.2.3.6.1 | RowsaRgIpMgmtDhcpFixedIpEntry | not-accessible | current | List of general parameters pertaining to LAN-Trans IP address reservations and leases. |
| 1.3.6.1.4.1.1429.79.2.3.6.1.1 | ColumnsaRgIpMgmtDhcpFixedIpIndex | not-accessible | current | The index of the the LAN IP Device in the LAN-Trans Realm. |
| 1.3.6.1.4.1.1429.79.2.3.6.1.2 | ColumnsaRgIpMgmtDhcpFixedIpRowStatus | read-write | current | The row status. A row can be destroyed. |
| 1.3.6.1.4.1.1429.79.2.3.6.1.4 | ColumnsaRgIpMgmtDhcpFixedIpAddress | read-write | current | |
| 1.3.6.1.4.1.1429.79.2.3.6.1.5 | ColumnsaRgIpMgmtDhcpFixedIpPhysAddr | read-create | current | The client's (i.e., LAN IP Device's) hardware address as indicated in the chaddr field of its DHCP REQUEST message. |
| 1.3.6.1.4.1.1429.79.2.3.6.1.6 | ColumnsaRgIpMgmtDhcpFixedIpHostName | read-write | current | This is the Host Name of the LAN IP address, based on DCHP option 12. |
| 1.3.6.1.4.1.1429.79.2.3.8 | TablesaRgIpMgmtStaticRouteTable | not-accessible | current | Static route entries in the routing table. This table is saved in non-vol and is empty after factory reset. |
| 1.3.6.1.4.1.1429.79.2.3.8.1 | RowsaRgIpMgmtStaticRouteEntry | not-accessible | current | List of static route entries in the routing table. |
| 1.3.6.1.4.1.1429.79.2.3.8.1.1 | ColumnsaRgIpMgmtStaticRouteIndex | not-accessible | current | The index of the the table. |
| 1.3.6.1.4.1.1429.79.2.3.8.1.2 | ColumnsaRgIpMgmtStaticRouteRowStatus | read-write | current | The row status. |
| 1.3.6.1.4.1.1429.79.2.3.8.1.3 | ColumnsaRgIpMgmtStaticRouteNetwork | read-write | current | Static route IP network definition |
| 1.3.6.1.4.1.1429.79.2.3.8.1.4 | ColumnsaRgIpMgmtStaticRouteSubnetMask | read-write | current | Static route network mask definition |
| 1.3.6.1.4.1.1429.79.2.3.8.1.5 | ColumnsaRgIpMgmtStaticRouteGateway | read-write | current | Gateway to the network defined in saRgIpMgmtStaticRouteNetwork and saRgIpMgmtStaticRouteSubnetMask. |
| 1.3.6.1.4.1.1429.79.2.3.8.1.6 | ColumnsaRgIpMgmtStaticRouteRipAdvertise | read-write | current | If set to true(1), then static route entry will be advertised in RIP. |
| 1.3.6.1.4.1.1429.79.2.3.9 | NodesaRgIpMgmtWanAddr | |||
| 1.3.6.1.4.1.1429.79.2.3.9.1 | NodesaRgIpMgmtWanAddrBase | |||
| 1.3.6.1.4.1.1429.79.2.3.9.1.1 | ScalarsaRgIpMgmtWanMode | read-write | current | When dualIp(3) is selected, the second IP stack is used for user operations. Stored in non-vol, dhcp(1) after factory reset. |
| 1.3.6.1.4.1.1429.79.2.3.9.1.2 | ScalarsaRgIpMgmtWanMtu | read-write | current | MTU size for the IP layer. Valid range is 256 to 1500. 0 is the default which is 1500. Stored in non-vol, 0 after factory reset. |
| 1.3.6.1.4.1.1429.79.2.3.9.1.3 | ScalarsaRgIpMgmtWanTtl | read-write | current | TTL for the IP packets forwarded to WAN. 0 means no change to the original TTL (after being decreased by 1). Stored in non-vol, 0 after factory reset. |
| 1.3.6.1.4.1.1429.79.2.3.9.3 | NodesaRgIpMgmtWanAddrStatic | |||
| 1.3.6.1.4.1.1429.79.2.3.9.3.1 | ScalarsaRgIpMgmtWanStaticNetwork | read-write | current | Stored in non-vol, 0.0.0.0 after factory reset. |
| 1.3.6.1.4.1.1429.79.2.3.9.3.2 | ScalarsaRgIpMgmtWanStaticSubnetMask | read-write | current | Stored in non-vol, 0.0.0.0 after factory reset. |
| 1.3.6.1.4.1.1429.79.2.3.9.3.3 | ScalarsaRgIpMgmtWanStaticGateway | read-write | current | Stored in non-vol, 0.0.0.0 after factory reset. |
| 1.3.6.1.4.1.1429.79.2.3.9.4 | NodesaRgIpMgmtWanAddrDualIp | |||
| 1.3.6.1.4.1.1429.79.2.3.9.4.1 | ScalarsaRgIpMgmtWanDualIpAddr | read-only | current | IP address for the second IP stack. If not specified and saRgIpMgmtWanMode is set to dualIp(3), DHCP is used to acquire the IP address. Note: this object can o… |
| 1.3.6.1.4.1.1429.79.2.3.9.4.2 | ScalarsaRgIpMgmtWanDualIpRipAdvertised | read-write | current | Specifies if the IP address is to be advertised in RIP, if RIP is enabled. Note: this object can only be set from config file. |
| 1.3.6.1.4.1.1429.79.2.3.11 | TablesaRgIpMgmtLanExtraSubnetTable | not-accessible | current | Additional IP addresses for primary LAN interface. If RIP is enabled, all subnets are advertised. All objects are stored in non-vol. The table is empty after f… |
| 1.3.6.1.4.1.1429.79.2.3.11.1 | RowsaRgIpMgmtLanExtraSubnetEntry | not-accessible | current | List of networks on the LAN side. |
| 1.3.6.1.4.1.1429.79.2.3.11.1.1 | ColumnsaRgIpMgmtLanExtraSubnetIndex | not-accessible | current | Indicates the instance of this table row. |
| 1.3.6.1.4.1.1429.79.2.3.11.1.2 | ColumnsaRgIpMgmtLanExtraSubnetRowStatus | read-write | current | The row status. |
| 1.3.6.1.4.1.1429.79.2.3.11.1.3 | ColumnsaRgIpMgmtLanExtraSubnetIpAddress | read-write | current | |
| 1.3.6.1.4.1.1429.79.2.3.11.1.4 | ColumnsaRgIpMgmtLanExtraSubnetSubnetMask | read-write | current | |
| 1.3.6.1.4.1.1429.79.2.3.11.1.5 | ColumnsaRgIpMgmtLanExtraSubnetGateway | read-write | current | |
| 1.3.6.1.4.1.1429.79.2.3.13 | NodesaRgIpMgmtLanPortControl | |||
| 1.3.6.1.4.1.1429.79.2.3.13.1 | TablesaRgIpMgmtLanPortControlTable | not-accessible | current | Table to control the mode for each LAN PORT. LAN PORTs are numbered 1-4 and are mapped to physical port location. Each port can either be in router or in bridg… |
| 1.3.6.1.4.1.1429.79.2.3.13.1.1 | RowsaRgIpMgmtLanPortControlEntry | not-accessible | current | |
| 1.3.6.1.4.1.1429.79.2.3.13.1.1.1 | ColumnsaRgIpMgmtLanPortControlIndex | not-accessible | current | The index for each LAN port |
| 1.3.6.1.4.1.1429.79.2.3.13.1.1.2 | ColumnsaRgIpMgmtLanPortMode | read-write | current | Each physical LAN port can either be controlled as bridge or router. The saRgIpMgmtLanPortMode MIB only works when SaRgIpMgmtLanMode.32=4(Mixed). Setting this … |
| 1.3.6.1.4.1.1429.79.2.3.1001 | ScalarsaRgIpMgmtApplySettings | read-write | current | If set to true(1), then all the settings (MIB values) from this MIB tree will be applied to run time configuration, modifying previous RG operation with the ne… |
| 1.3.6.1.4.1.1429.79.2.4 | NodesaRgFirewall | |||
| 1.3.6.1.4.1.1429.79.2.4.4 | NodesaRgFirewallReport | |||
| 1.3.6.1.4.1.1429.79.2.4.4.1 | TablesaRgFirewallReportEventTable | not-accessible | current | This table is stored in non-vol and is empty after factory reset. |
| 1.3.6.1.4.1.1429.79.2.4.4.1.1 | RowsaRgFirewallReportEventEntry | not-accessible | current | |
| 1.3.6.1.4.1.1429.79.2.4.4.1.1.1 | ColumnsaRgFirewallReportEventIndex | not-accessible | current | The index |
| 1.3.6.1.4.1.1429.79.2.4.4.1.1.2 | ColumnsaRgFirewallReportEventDescription | read-only | current | |
| 1.3.6.1.4.1.1429.79.2.4.4.1.1.3 | ColumnsaRgFirewallReportEventCount | read-only | current | |
| 1.3.6.1.4.1.1429.79.2.4.4.1.1.4 | ColumnsaRgFirewallReportEventLastOccurance | read-only | current | |
| 1.3.6.1.4.1.1429.79.2.4.4.1.1.5 | ColumnsaRgFirewallReportEventTarget | read-only | current | |
| 1.3.6.1.4.1.1429.79.2.4.4.1.1.6 | ColumnsaRgFirewallReportEventSource | read-only | current | |
| 1.3.6.1.4.1.1429.79.2.4.4.2 | NodesaRgFirewallReportMgmt | |||
| 1.3.6.1.4.1.1429.79.2.4.4.2.1 | ScalarsaRgFirewallReportMgmtClearLog | read-write | current | Note: this object does not need saRgFirewallApplySettings to take effect. |
| 1.3.6.1.4.1.1429.79.2.4.4.2.2 | ScalarsaRgFirewallReportEmailLogNow | read-write | current | Triggers sending currect logs via email. Always returns false. Note: this objects does not need saRgFirewallApplySettings to send the logs. |
| 1.3.6.1.4.1.1429.79.2.4.4.3 | NodesaRgFirewallReportEmail | |||
| 1.3.6.1.4.1.1429.79.2.4.4.3.1 | ScalarsaRgFirewallReportEmailEnable | read-write | current | Enables sending logs via email. Email is sent when an event happens. |
| 1.3.6.1.4.1.1429.79.2.4.4.3.2 | ScalarsaRgFirewallReportEmailAddress | read-write | current | This is stored in non-vol and is empty after factory reset. |
| 1.3.6.1.4.1.1429.79.2.4.4.3.3 | ScalarsaRgFirewallReportEmailSmtpServer | read-write | current | IP address or FQDN. Stored in non-vol. Empty after factory reset. |
| 1.3.6.1.4.1.1429.79.2.4.4.3.4 | ScalarsaRgFirewallReportEmailUsername | read-write | current | This is stored in non-vol and is empty after factory reset. |
| 1.3.6.1.4.1.1429.79.2.4.4.3.5 | ScalarsaRgFirewallReportEmailPassword | read-write | current | This is stored in non-vol and is empty after factory reset. |
| 1.3.6.1.4.1.1429.79.2.4.5 | NodesaRgFirewallRules | |||
| 1.3.6.1.4.1.1429.79.2.4.5.1 | TablesaRgFirewallIpFilterTable | not-accessible | current | This table is stored in non-vol and is empty after factory reset. |
| 1.3.6.1.4.1.1429.79.2.4.5.1.1 | RowsaRgFirewallIpFilterEntry | not-accessible | current | |
| 1.3.6.1.4.1.1429.79.2.4.5.1.1.1 | ColumnsaRgFirewallIpFilterIndex | not-accessible | current | The index |
| 1.3.6.1.4.1.1429.79.2.4.5.1.1.2 | ColumnsaRgFirewallIpFilterRowStatus | read-write | current | The row status. A row can be destroyed. If the row is not used, set to notInService. |
| 1.3.6.1.4.1.1429.79.2.4.5.1.1.3 | ColumnsaRgFirewallIpFilterAddressStart | read-write | current | |
| 1.3.6.1.4.1.1429.79.2.4.5.1.1.4 | ColumnsaRgFirewallIpFilterAddressEnd | read-write | current | |
| 1.3.6.1.4.1.1429.79.2.4.5.2 | TablesaRgFirewallPortFilterTable | not-accessible | current | This table is stored in non-vol and is empty after factory reset. |
| 1.3.6.1.4.1.1429.79.2.4.5.2.1 | RowsaRgFirewallPortFilterEntry | not-accessible | current | |
| 1.3.6.1.4.1.1429.79.2.4.5.2.1.1 | ColumnsaRgFirewallPortFilterIndex | not-accessible | current | The index |
| 1.3.6.1.4.1.1429.79.2.4.5.2.1.2 | ColumnsaRgFirewallPortFilterRowStatus | read-write | current | The row status. A row can be destroyed. If the row is not used, set to notInService. |
| 1.3.6.1.4.1.1429.79.2.4.5.2.1.5 | ColumnsaRgFirewallPortFilterPortStart | read-write | current | |
| 1.3.6.1.4.1.1429.79.2.4.5.2.1.6 | ColumnsaRgFirewallPortFilterPortEnd | read-write | current | |
| 1.3.6.1.4.1.1429.79.2.4.5.2.1.7 | ColumnsaRgFirewallPortFilterProto | read-write | current | IP protocol to block. |
| 1.3.6.1.4.1.1429.79.2.4.5.3 | TablesaRgFirewallMacFilterTable | not-accessible | current | A table of clients MAC addresses that are denied from accessing Internet. |
| 1.3.6.1.4.1.1429.79.2.4.5.3.1 | RowsaRgFirewallMacFilterEntry | not-accessible | current | A row in the table that specifies a single station MAC address. |
| 1.3.6.1.4.1.1429.79.2.4.5.3.1.1 | ColumnsaRgFirewallMacFilterIndex | not-accessible | current | The index |
| 1.3.6.1.4.1.1429.79.2.4.5.3.1.2 | ColumnsaRgFirewallMacFilterRowStatus | read-write | current | The row status. A row can be destroyed. If the row is not used, set to notInService. |
| 1.3.6.1.4.1.1429.79.2.4.5.3.1.3 | ColumnsaRgFirewallMacFilterAddress | read-write | current | A MAC address of a station that cannot access Internet. |
| 1.3.6.1.4.1.1429.79.2.4.5.4 | ScalarsaRgFirewallMacFilterEnable | read-write | current | True = Enable the Mac address filtering feature. False = disable. this Value is written to non-vol and set to false after a factory reset. |
| 1.3.6.1.4.1.1429.79.2.4.5.5 | ScalarsaRgFirewallMacFilterMode | read-write | current | block(0)- Macs listed in the saRgFirewallMacFilterEntryTable will be blocked. permit(1)- Macs listed in the saRgFirewallMacFilterEntryTable will be permitted. … |
| 1.3.6.1.4.1.1429.79.2.4.6 | TablesaRgFirewallPortFwdTable | not-accessible | current | This table is stored in non-vol and is empty after factory reset. |
| 1.3.6.1.4.1.1429.79.2.4.6.1 | RowsaRgFirewallPortFwdEntry | not-accessible | current | |
| 1.3.6.1.4.1.1429.79.2.4.6.1.1 | ColumnsaRgFirewallPortFwdIndex | not-accessible | current | The index |
| 1.3.6.1.4.1.1429.79.2.4.6.1.2 | ColumnsaRgFirewallPortFwdRowStatus | read-write | current | The row status. A row can be destroyed. If the row is not used, set to notInService. |
| 1.3.6.1.4.1.1429.79.2.4.6.1.3 | ColumnsaRgFirewallPortFwdToAddress | read-write | current | Valid address must be entered for a row to be created. |
| 1.3.6.1.4.1.1429.79.2.4.6.1.4 | ColumnsaRgFirewallPortFwdPortStart | read-write | current | Valid port must be entered for a row to be created. |
| 1.3.6.1.4.1.1429.79.2.4.6.1.5 | ColumnsaRgFirewallPortFwdPortEnd | read-write | current | Valid port must be entered for a row to be created. |
| 1.3.6.1.4.1.1429.79.2.4.6.1.6 | ColumnsaRgFirewallPortFwdProto | read-write | current | |
| 1.3.6.1.4.1.1429.79.2.4.6.1.8 | ColumnsaRgFirewallPortFwdExternalPortStart | read-write | current | Valid port must be entered for a row to be created. This is the outside-facing start port for the portforward. |
| 1.3.6.1.4.1.1429.79.2.4.6.1.9 | ColumnsaRgFirewallPortFwdExternalPortEnd | read-write | current | Valid port must be entered for a row to be created. This is the outside-facing end port for the portforward. |
| 1.3.6.1.4.1.1429.79.2.4.7 | TablesaRgFirewallPortTrigTable | not-accessible | current | This table is stored in non-vol and is empty after factory reset. |
| 1.3.6.1.4.1.1429.79.2.4.7.1 | RowsaRgFirewallPortTrigEntry | not-accessible | current | |
| 1.3.6.1.4.1.1429.79.2.4.7.1.1 | ColumnsaRgFirewallPortTrigIndex | not-accessible | current | The index |
| 1.3.6.1.4.1.1429.79.2.4.7.1.2 | ColumnsaRgFirewallPortTrigRowStatus | read-write | current | The row status. A row can be destroyed. If the row is not used, set to notInService. |
| 1.3.6.1.4.1.1429.79.2.4.7.1.3 | ColumnsaRgFirewallPortTrigTriggerPortStart | read-write | current | |
| 1.3.6.1.4.1.1429.79.2.4.7.1.4 | ColumnsaRgFirewallPortTrigTriggerPortEnd | read-write | current | |
| 1.3.6.1.4.1.1429.79.2.4.7.1.5 | ColumnsaRgFirewallPortTrigTargetPortStart | read-write | current | |
| 1.3.6.1.4.1.1429.79.2.4.7.1.6 | ColumnsaRgFirewallPortTrigTargetPortEnd | read-write | current | |
| 1.3.6.1.4.1.1429.79.2.4.7.1.7 | ColumnsaRgFirewallPortTrigProto | read-write | current | |
| 1.3.6.1.4.1.1429.79.2.4.1001 | ScalarsaRgFirewallApplySettings | read-write | current | If set to true(1), then all the settings (MIB values) from this MIB tree will be applied to run time configuration, modifying previous RG operation with the ne… |
| 1.3.6.1.4.1.1429.79.2.12 | NodesaRgDslite | |||
| 1.3.6.1.4.1.1429.79.2.12.1 | ScalarsaRgDsliteOption | read-write | current | This MIB will toggle whether DHCPv6 option 64 is requested in the solicit. The option should only be requested if DS Lite is enabled. |
| 1.3.6.1.4.1.1429.79.2.12.2 | ScalarsaRgDsliteAftrName | read-write | current | This MIB will read/write the remote IPv6 FQDN of the AFTR router in the DS Lite tunnel configuration. This should only have an effect if eRouter is in IPv6 onl… |
| 1.3.6.1.4.1.1429.79.2.12.3 | ScalarsaRgDsliteAftrAddress | read-write | current | This MIB will set the remote IPv6 address of the AFTR router manually in the DS Lite tunnel configuration. This should only have an effect if eRouter is in IPv… |
| 1.3.6.1.4.1.1429.79.2.12.4 | ScalarsaRgDsliteTcpMssClamping | read-write | current | Specifies whether TCP MSS clamping is enabled on the interface. 0 disables clamping, 1 clamps the MSS depending on the interface MTU. A value > 1 will be used … |
| 1.3.6.1.4.1.1429.79.2.12.1001 | ScalarsaRgDsliteApplySettings | read-write | current | If set to true(1), then all the settings (MIB values) from this MIB tree will be applied to the runtime configuration, This will resolve the AFTR domain name t… |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| SaRgTimeZone | INTEGER { gmtMinusTwelveEniwetokKwajalein(1), gmtMinusElevenMidwayIslandSamoa(2), gmtMinusTenHawaii(3), gmtMinusNineAlaska(4), gmtMinusEightPacificTimeCanadaTijuana(5), gmtMinusSevenArizona(6), gmtMinusSevenMountainTimeCanada(7), gmtMinusSixCentralAmerica(8), gmtMinusSixCentralTimeCanada(9), gmtMinusSixMexicoCity(10), gmtMinusSixSaskatchewan(11), gmtMinusFiveBogotaLimaQuito(12), gmtMinusFiveEasternTimeCanada(13), gmtMinusFiveIndianaEast(14), gmtMinusFourAtlanticTimeCanada(15), gmtMinusFourCaracasLaPaz(16), gmtMinusFourSantiago(17), gmtMinusThreeThirtyNewfoundland(18), gmtMinusThreeBrasilia(19), gmtMinusThreeBuenosAiresGeorgetown(20), gmtMinusThreeGreenland(21), gmtMinusTwoMid-Atlantic(22), gmtMinusOneAzores(23), gmtMinusOneCapeVerdeIs(24), gmtZeroCasablancaMonrovia(25), gmtZeroDublinEdinburghLisbonLondon(26), gmtPlusOneAmsterdamBerlinRomeStockholmVienna(27), gmtPlusOneBelgradeBratislavaBudapestLjubljanaPrague(28), gmtPlusOneBrusselsCopenhagenMadridParis(29), gmtPlusOneSarajevoSkopjeSofijaVilniusWarsawZagreb(30), gmtPlusOneWestCentralAfrica(31), gmtPlusTwoAthensIstanbilMinsk(32), gmtPlusTwoBucharest(33), gmtPlusTwoHelsinkiRigaTallinn(34), gmtPlusTwoJerusalem(35), gmtPlusThreeBaghdad(36), gmtPlusThreeMoscowStPetersburgVolgograd(37), gmtPlusThreeNairobi(38), gmtPlusThreeThirtyTehran(39), gmtPlusFourAbuDhabiMuscat(40), gmtPlusFourThirtyKabul(41), gmtPlusFiveEkaterinburg(42), gmtPlusFiveThirtyCalcuttaChennaiMumbaiNewDelhi(43), gmtPlusFiveFourtyFiveKathmandu(44), gmtPlusSixAlmatyNovosibirsk(45), gmtPlusSixAstanaDhaka(46), gmtPlusSixThirtyRangoon(47), gmtPlusSevenBangkokHanoiJakarta(48), gmtPlusSevenKrasnoyarsk(49), gmtPlusEightBeijingChongqingHongKongUrumqi(50), gmtPlusEightIrkustkUlaanBataar(51), gmtPlusEightKualaLumpurSingapore(52), gmtPlusEightTaipei(53), gmtPlusNineOsakaSapporoTokyo(54), gmtPlusNineSeoul(55), gmtPlusNineThirtyAdelaide(56), gmtPlusTenBrisbane(57), gmtPlusTenVladivostok(58), gmtPlusElevenMagadanSolomonIsNewCaledonia(59), gmtPlusTwelveAucklandWellington(60), gmtPlusTwelveFiji(61), gmtPlusThirteenNukuAlofa(62) } | current | Time zones. |