SCTE-HMS-HEADENDIDENT-TC-MIB
14 objects
No module-level DESCRIPTION found.
Imported Objects
| SNMPv2-SMI | enterprises Integer32 MODULE-IDENTITY Unsigned32 |
| SNMPv2-TC | TEXTUAL-CONVENTION |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| HeAlarmControl | INTEGER { alarmEnabled(1), alarmDisabled(2) } | current | Alarm Control value for a specific device. This object is used to control sending traps related to this headend entity or enabling disabling of raising an alarm condition for a specific entity. |
| HeDigitalAlarmSeverity | INTEGER { critical(1), major(2), minor(3), warning(4), status(5), clear(6), information(7) } | current | The alarm severity that is determined by the device and sent over in the trap message. |
| HeDigitalAlarmType | INTEGER { communication(1), process(2), session(3), capacity(4), maintenance(5), provisioning(6), programMgmt(7), redundancy(8), other(9) } | current | The alarm type that describes the Event that caused the alarm. |
| HeFaultStatus | INTEGER { normal(1), fault(2) } | current | An enumerated value that provides a fault status of a particular hardware or software parameter that usually represent some sort of condition. A value normal(1) indicates the normal condition. A value fault(2) indicates… |
| HeHundredthNanoMeter | Unsigned32 | current | This data type represents wavelength values that are normally expressed in nano meters. Units are in hundredths of a NanoMeter; for example, 1550.56 nm will be represented as 155056. |
| HeHundredthWatts | Unsigned32 | current | This data type represents power values that are normally expressed in watts. Units are in hundredths of a watt; for example, 420 watts will be represented as 42000. |
| HeMilliAmp | Unsigned32 | current | This data type represents current levels that are normally expressed in amperes. Units are in milliamperes; for example, 2.1 Amperes would be expressed as 2100. |
| HeOnOffControl | INTEGER { off(1), on(2), meaningless(3) } | current | An enumerated value that provides a control of a particular hardware or software parameter that usually represent some sort of switch. A SET request with a value off(1) will cause the switch to be shut off. A SET reques… |
| HeOnOffStatus | INTEGER { off(1), on(2) } | current | An enumerated value that provides a status of a particular hardware or software parameter that usually represent some sort of switch. A value off(1) indicates the switch is off. A value on(2) indicates the switch is on. |
| HeTenthCentigrade | Integer32 | current | This data type represents temperature values that are normally expressed in Centigrade. Units are in tenths of a Centigrade; for example, -5.1 Centigrade will be represented as -51. |
| HeTenthdB | Integer32 | current | This data type represents power levels that are normally expressed in dB. Units are in tenths of a dB; for example, -5.1 dB will be represented as -51. |
| HeTenthdBm | Integer32 | current | This data type represents power levels that are normally expressed in dBm. Units are in tenths of a dBm; for example, -5.1 dBm will be represented as -51. |
| HeTenthdBmV | Integer32 | current | This data type represents power levels that are normally expressed in dBmV. Units are in tenths of a dBmV; for example, -5.1 dBmV will be represented as -51. |
| HeTrapRegenerate | INTEGER { trapRegenerate(1), trapNormal(2) } | current | This value tells the SNMP Agent to send the Trap Regenerate Trap for all values of Current alarms for this entity. The device can provide for a means to send ALL current alarms, not just one specific entity. |