SDS-BIG-STSW-MIB
305 objects
The MIB module to describe generic objects for AN-D.cz devices - SDS BIG and SDS STSW (and all the sub-variants using the STSW module), firmware of Q4-2019 and newer.
Imported Objects
| SNMPv2-SMI | Counter32 enterprises Gauge32 Integer32 IpAddress MODULE-IDENTITY OBJECT-TYPE TimeTicks |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.33283 | Identitymib-AN-Dcz-SDS | The MIB module to describe generic objects for AN-D.cz devices - SDS BIG and SDS STSW (and all the sub-variants using the STSW module), firmware of Q4-2019 and… | ||
| 1.3.6.1.4.1.33283.1 | Nodesdsxpublic | |||
| 1.3.6.1.4.1.33283.1.30 | NodesdsBIGandSTSW | |||
| 1.3.6.1.4.1.33283.1.30.1 | NodesdsIPWatchdog | |||
| 1.3.6.1.4.1.33283.1.30.1.1 | ScalaripwActive | read-only | current | The current IP watchdog status. |
| 1.3.6.1.4.1.33283.1.30.1.2 | ScalaripwPingIP | read-only | current | IP address of the wdg-monitored object. |
| 1.3.6.1.4.1.33283.1.30.1.3 | ScalaripwPauseAfterPwOn | read-only | current | Amount of time in [sec]. Duration of the IP watchdog disable period, applied when watchdog device itself is first powered on. |
| 1.3.6.1.4.1.33283.1.30.1.4 | ScalaripwPingTimeout | read-only | current | Config value - the RTT timeout. |
| 1.3.6.1.4.1.33283.1.30.1.5 | ScalaripwRepeatPingPer | read-only | current | PING REQUEST packet sending: the configured send repeat period, in [miliseconds]. |
| 1.3.6.1.4.1.33283.1.30.1.6 | ScalaripwIgnoreLostCnt | read-only | current | How many lost PING REPLY packets should get ignored, before activating the relay. |
| 1.3.6.1.4.1.33283.1.30.1.7 | ScalaripwPauseWdAfterAct | read-only | current | Delay of the IP watchdog pause, applied when the output relay is activated (e.g. the time for controlled device recovery). |
| 1.3.6.1.4.1.33283.1.30.1.8 | ScalaripwRelayActTime | read-only | current | How many [seconds] should be the output relay activated. |
| 1.3.6.1.4.1.33283.1.30.1.9 | ScalaripwActualFailed | read-only | current | How many unreceived PING REPLY packets are detected so far. |
| 1.3.6.1.4.1.33283.1.30.1.10 | ScalaripwLastRTT | read-only | current | Round Trip Time for the last ping echo. |
| 1.3.6.1.4.1.33283.1.30.1.11 | ScalaripwActualRelayState | read-only | current | Actual (virtual) output relay status (before mapping this status to the selected hardware). |
| 1.3.6.1.4.1.33283.1.30.2 | NodesdsOptoInput | |||
| 1.3.6.1.4.1.33283.1.30.2.1 | Scalaropto1 | read-only | current | Current OPTO1 binary input status. |
| 1.3.6.1.4.1.33283.1.30.2.2 | Scalaropto2 | read-only | current | Current OPTO2 binary input status. |
| 1.3.6.1.4.1.33283.1.30.2.3 | Scalaropto3 | read-only | current | Current OPTO3 binary input status. |
| 1.3.6.1.4.1.33283.1.30.2.4 | Scalaropto4 | read-only | current | Current OPTO4 binary input status. |
| 1.3.6.1.4.1.33283.1.30.2.5 | Scalaropto5 | read-only | current | Current OPTO5 binary input status. |
| 1.3.6.1.4.1.33283.1.30.2.6 | Scalaropto6 | read-only | current | Current OPTO6 binary input status. |
| 1.3.6.1.4.1.33283.1.30.2.7 | Scalaropto7 | read-only | current | Current OPTO7 binary input status. |
| 1.3.6.1.4.1.33283.1.30.2.8 | Scalaropto8 | read-only | current | Current OPTO8 binary input status. |
| 1.3.6.1.4.1.33283.1.30.2.9 | Scalarlogics0input | read-only | current | Current LOGIC-S0 binary input status. |
| 1.3.6.1.4.1.33283.1.30.3 | NodesdsOutputRelays | |||
| 1.3.6.1.4.1.33283.1.30.3.1 | NodesdsOutputRelay1 | |||
| 1.3.6.1.4.1.33283.1.30.3.1.1 | ScalarsdsRE1state | read-write | current | Current RELAY 1 output status. |
| 1.3.6.1.4.1.33283.1.30.3.1.2 | ScalarsdsRE1cby | read-write | current | RELAY 1 controled by ... |
| 1.3.6.1.4.1.33283.1.30.3.1.3 | ScalarsdsRE1name | read-only | current | User name for RELAY 1. |
| 1.3.6.1.4.1.33283.1.30.3.2 | NodesdsOutputRelay2 | |||
| 1.3.6.1.4.1.33283.1.30.3.2.1 | ScalarsdsRE2state | read-write | current | Current RELAY 2 output status. |
| 1.3.6.1.4.1.33283.1.30.3.2.2 | ScalarsdsRE2cby | read-write | current | RELAY 2 controled by ... |
| 1.3.6.1.4.1.33283.1.30.3.2.3 | ScalarsdsRE2name | read-only | current | User name for RELAY 2. |
| 1.3.6.1.4.1.33283.1.30.3.3 | NodesdsOutputRelay3 | |||
| 1.3.6.1.4.1.33283.1.30.3.3.1 | ScalarsdsRE3state | read-write | current | Current RELAY 3 output status. |
| 1.3.6.1.4.1.33283.1.30.3.3.2 | ScalarsdsRE3cby | read-write | current | RELAY 3 controled by ... |
| 1.3.6.1.4.1.33283.1.30.3.3.3 | ScalarsdsRE3name | read-only | current | User name for RELAY 3. |
| 1.3.6.1.4.1.33283.1.30.3.4 | NodesdsOutputRelay4 | |||
| 1.3.6.1.4.1.33283.1.30.3.4.1 | ScalarsdsRE4state | read-write | current | Current RELAY 4 output status. |
| 1.3.6.1.4.1.33283.1.30.3.4.2 | ScalarsdsRE4cby | read-write | current | RELAY 4 controled by ... |
| 1.3.6.1.4.1.33283.1.30.3.4.3 | ScalarsdsRE4name | read-only | current | User name for RELAY 4. |
| 1.3.6.1.4.1.33283.1.30.3.5 | NodesdsOutputRelay5 | |||
| 1.3.6.1.4.1.33283.1.30.3.5.1 | ScalarsdsRE5state | read-write | current | Current RELAY 5 output status. |
| 1.3.6.1.4.1.33283.1.30.3.5.2 | ScalarsdsRE5cby | read-write | current | RELAY 5 controled by ... |
| 1.3.6.1.4.1.33283.1.30.3.5.3 | ScalarsdsRE5name | read-only | current | User name for RELAY 5. |
| 1.3.6.1.4.1.33283.1.30.3.6 | NodesdsOutputRelay6 | |||
| 1.3.6.1.4.1.33283.1.30.3.6.1 | ScalarsdsRE6state | read-write | current | Current RELAY 6 output status. |
| 1.3.6.1.4.1.33283.1.30.3.6.2 | ScalarsdsRE6cby | read-write | current | RELAY 6 controled by ... |
| 1.3.6.1.4.1.33283.1.30.3.6.3 | ScalarsdsRE6name | read-only | current | User name for RELAY 6. |
| 1.3.6.1.4.1.33283.1.30.4 | NodesdsPWMoutput | |||
| 1.3.6.1.4.1.33283.1.30.4.1 | ScalarsdsPWM1freq | read-write | current | Actual PWM1 generator frequency [Hz]. |
| 1.3.6.1.4.1.33283.1.30.4.2 | ScalarsdsPWM1duty | read-write | current | Actual PWM1 duty control setting. |
| 1.3.6.1.4.1.33283.1.30.5 | NodesdsADCinputs | |||
| 1.3.6.1.4.1.33283.1.30.5.1 | NodesdsADCitem0 | |||
| 1.3.6.1.4.1.33283.1.30.5.1.1 | ScalarsdsADCrawValue0 | read-only | current | Actual raw analog input [R] value (conversion result). |
| 1.3.6.1.4.1.33283.1.30.5.1.2 | ScalarsdsADCtext0 | read-only | current | SI textual value for the analog input (conversion result). |
| 1.3.6.1.4.1.33283.1.30.5.1.3 | ScalarsdsADCintmul0 | read-only | current | SI integer MUL value for the analog input (conversion result multiplied by 100). |
| 1.3.6.1.4.1.33283.1.30.5.1.4 | ScalarsdsADCname0 | read-only | current | User name for the analog input. |
| 1.3.6.1.4.1.33283.1.30.5.2 | NodesdsADCitem1 | |||
| 1.3.6.1.4.1.33283.1.30.5.2.1 | ScalarsdsADCrawValue1 | read-only | current | Actual raw analog input [V] value (conversion result). |
| 1.3.6.1.4.1.33283.1.30.5.2.2 | ScalarsdsADCtext1 | read-only | current | SI textual value for the analog input (conversion result). |
| 1.3.6.1.4.1.33283.1.30.5.2.3 | ScalarsdsADCintmul1 | read-only | current | SI integer MUL value for the analog input (conversion result multiplied by 100). |
| 1.3.6.1.4.1.33283.1.30.5.2.4 | ScalarsdsADCname1 | read-only | current | User name for the analog input. |
| 1.3.6.1.4.1.33283.1.30.5.3 | NodesdsADCitem2 | |||
| 1.3.6.1.4.1.33283.1.30.5.3.1 | ScalarsdsADCrawValue2 | read-only | current | Actual raw analog input [V] value (conversion result). |
| 1.3.6.1.4.1.33283.1.30.5.3.2 | ScalarsdsADCtext2 | read-only | current | SI textual value for the analog input (conversion result). |
| 1.3.6.1.4.1.33283.1.30.5.3.3 | ScalarsdsADCintmul2 | read-only | current | SI integer MUL value for the analog input (conversion result multiplied by 100). |
| 1.3.6.1.4.1.33283.1.30.5.3.4 | ScalarsdsADCname2 | read-only | current | User name for the analog input. |
| 1.3.6.1.4.1.33283.1.30.5.4 | NodesdsADCitem3 | |||
| 1.3.6.1.4.1.33283.1.30.5.4.1 | ScalarsdsADCrawValue3 | read-only | current | Actual raw analog input [AI1] value (conversion result). |
| 1.3.6.1.4.1.33283.1.30.5.4.2 | ScalarsdsADCtext3 | read-only | current | SI textual value for the analog input (conversion result). |
| 1.3.6.1.4.1.33283.1.30.5.4.3 | ScalarsdsADCintmul3 | read-only | current | SI integer MUL value for the analog input (conversion result multiplied by 100). |
| 1.3.6.1.4.1.33283.1.30.5.4.4 | ScalarsdsADCname3 | read-only | current | User name for the analog input. |
| 1.3.6.1.4.1.33283.1.30.5.5 | NodesdsADCitem4 | |||
| 1.3.6.1.4.1.33283.1.30.5.5.1 | ScalarsdsADCrawValue4 | read-only | current | Actual raw analog input [AI2] value (conversion result). |
| 1.3.6.1.4.1.33283.1.30.5.5.2 | ScalarsdsADCtext4 | read-only | current | SI textual value for the analog input (conversion result). |
| 1.3.6.1.4.1.33283.1.30.5.5.3 | ScalarsdsADCintmul4 | read-only | current | SI integer MUL value for the analog input (conversion result multiplied by 100). |
| 1.3.6.1.4.1.33283.1.30.5.5.4 | ScalarsdsADCname4 | read-only | current | User name for the analog input. |
| 1.3.6.1.4.1.33283.1.30.5.6 | NodesdsADCitem5 | |||
| 1.3.6.1.4.1.33283.1.30.5.6.1 | ScalarsdsADCrawValue5 | read-only | current | Actual raw analog input [AI3] value (conversion result). |
| 1.3.6.1.4.1.33283.1.30.5.6.2 | ScalarsdsADCtext5 | read-only | current | SI textual value for the analog input (conversion result). |
| 1.3.6.1.4.1.33283.1.30.5.6.3 | ScalarsdsADCintmul5 | read-only | current | SI integer MUL value for the analog input (conversion result multiplied by 100). |
| 1.3.6.1.4.1.33283.1.30.5.6.4 | ScalarsdsADCname5 | read-only | current | User name for the analog input. |
| 1.3.6.1.4.1.33283.1.30.5.7 | NodesdsADCitem6 | |||
| 1.3.6.1.4.1.33283.1.30.5.7.1 | ScalarsdsADCrawValue6 | read-only | current | Actual raw analog input [AI4] value (conversion result). |
| 1.3.6.1.4.1.33283.1.30.5.7.2 | ScalarsdsADCtext6 | read-only | current | SI textual value for the analog input (conversion result). |
| 1.3.6.1.4.1.33283.1.30.5.7.3 | ScalarsdsADCintmul6 | read-only | current | SI integer MUL value for the analog input (conversion result multiplied by 100). |
| 1.3.6.1.4.1.33283.1.30.5.7.4 | ScalarsdsADCname6 | read-only | current | User name for the analog input. |
| 1.3.6.1.4.1.33283.1.30.5.8 | NodesdsADCitem7 | |||
| 1.3.6.1.4.1.33283.1.30.5.8.1 | ScalarsdsADCrawValue7 | read-only | current | Actual raw analog input [AI5] value (conversion result). |
| 1.3.6.1.4.1.33283.1.30.5.8.2 | ScalarsdsADCtext7 | read-only | current | SI textual value for the analog input (conversion result). |
| 1.3.6.1.4.1.33283.1.30.5.8.3 | ScalarsdsADCintmul7 | read-only | current | SI integer MUL value for the analog input (conversion result multiplied by 100). |
| 1.3.6.1.4.1.33283.1.30.5.8.4 | ScalarsdsADCname7 | read-only | current | User name for the analog input. |
| 1.3.6.1.4.1.33283.1.30.6 | TablesdsOneWireTable | not-accessible | current | A list of 1-Wire (reg) devices. |
| 1.3.6.1.4.1.33283.1.30.6.1 | RowsdsOneWireEntry | not-accessible | current | An entry containing information applicable to a particular 1-WIRE device. |
| 1.3.6.1.4.1.33283.1.30.6.1.1 | ColumnsdsOneWireStatus | read-only | current | Actual 1-WIRE device status. The sub-states for the 'working(8)' state are not provided yet. |
| 1.3.6.1.4.1.33283.1.30.6.1.2 | ColumnsdsOneWireDeviceROMcode | read-only | current | Internal 1-WIRE device ROM unique identification code. |
| 1.3.6.1.4.1.33283.1.30.6.1.3 | ColumnsdsOneWireName | read-only | current | Internal 1-WIRE device ROM unique identification code. |
| 1.3.6.1.4.1.33283.1.30.6.1.4 | ColumnsdsOneWireFullValIDX0 | read-only | current | Primary value received from this 1-WIRE device. |
| 1.3.6.1.4.1.33283.1.30.6.1.5 | ColumnsdsOneWireFullValIDX1 | read-only | current | Secondary value received from this 1-WIRE device. |
| 1.3.6.1.4.1.33283.1.30.6.1.6 | ColumnsdsOneWireConfigFlags | read-only | current | Configuration flags for this 1-WIRE device. |
| 1.3.6.1.4.1.33283.1.30.6.1.7 | ColumnsdsOneWireTableRowIndex | not-accessible | current | 1-WIRE table row index. |
| 1.3.6.1.4.1.33283.1.30.7 | NodesdsVersionEntry | |||
| 1.3.6.1.4.1.33283.1.30.7.1 | ScalarsdsVersionText | read-only | current | SDS device version text. |
| 1.3.6.1.4.1.33283.1.30.7.2 | ScalarsdsCustomVarTrap1 | read-only | current | SDS custom-trap value. |
| 1.3.6.1.4.1.33283.1.30.7.3 | ScalarsdsCustomVarTrap2 | read-only | current | SDS custom-trap value. |
| 1.3.6.1.4.1.33283.1.30.7.4 | ScalarsdsCustomVarTrap3 | read-only | current | SDS custom-trap value. |
| 1.3.6.1.4.1.33283.1.30.7.5 | ScalarsdsCustomVarTrap4 | read-only | current | SDS custom-trap value. |
| 1.3.6.1.4.1.33283.1.30.7.6 | ScalarsdsCustomVarTrap5 | read-only | current | SDS custom-trap value. |
| 1.3.6.1.4.1.33283.1.30.7.7 | ScalarsdsCustomVarTrap6 | read-only | current | SDS custom-trap value. |
| 1.3.6.1.4.1.33283.1.30.7.8 | ScalarsdsCustomVarTrap7 | read-only | current | SDS custom-trap value. |
| 1.3.6.1.4.1.33283.1.30.7.9 | ScalarsdsCustomVarTrap8 | read-only | current | SDS custom-trap value. |
| 1.3.6.1.4.1.33283.1.30.7.10 | ScalarsdsCustomVarTrap9 | read-only | current | SDS custom-trap value. |
| 1.3.6.1.4.1.33283.1.30.8 | NodesdsGeneralInfoEntry | |||
| 1.3.6.1.4.1.33283.1.30.8.1 | ScalarsdsNTPvalue | read-only | current | Actual NTP UTC time value (pure UTC from NTP, not corrected for a local time offset). |
| 1.3.6.1.4.1.33283.1.30.8.2 | ScalarsdsSoCtempValue | read-only | current | Actual SoC chip internal temperature, represented in a special units [0..4095]. This needs to be recalculated to get a degC value. |
| 1.3.6.1.4.1.33283.1.30.8.3 | ScalarsdsOneWireBUSAcountValue | read-only | current | Number of discovered 1-Wire devices on BUS A. |
| 1.3.6.1.4.1.33283.1.30.8.4 | ScalarsdsOneWireBUSBcountValue | read-only | current | Number of discovered 1-Wire devices on BUS B. |
| 1.3.6.1.4.1.33283.1.30.8.5 | ScalarsdsGPIOTOPBOARDoutputState | read-only | current | GPIO-TOPBOARD actual output status. |
| 1.3.6.1.4.1.33283.1.30.8.6 | ScalarsdsGPIOTOPBOARDdirection | read-only | current | GPIO-TOPBOARD actual direction (in/out) status. |
| 1.3.6.1.4.1.33283.1.30.8.7 | ScalarsdsBackUpCoinBatteryVoltageValue | read-only | current | Actual voltage reading of the back-up coin battery, represented in a special units [0..4095]. This needs to be recalculated to get a value in Votls. |
| 1.3.6.1.4.1.33283.1.30.8.10 | ScalarsdsNTPvalueLocal | read-only | current | Actual LOCAL time value. |
| 1.3.6.1.4.1.33283.1.30.8.11 | ScalarsdsSDCARDpresence | read-only | current | Physical presence (insertion) of the SD-CARD. |
| 1.3.6.1.4.1.33283.1.30.8.12 | ScalarsdsSDCARDlastSN | read-only | current | Last known SN of the SD-CARD. |
| 1.3.6.1.4.1.33283.1.30.8.13 | ScalarsdsSDCARDreadCNT | read-only | current | Number of sector reads from the SD-CARD. |
| 1.3.6.1.4.1.33283.1.30.8.14 | ScalarsdsSDCARDwriteCNT | read-only | current | Number of sector writes from the SD-CARD. |
| 1.3.6.1.4.1.33283.1.30.8.15 | ScalarsdsSDCARDrwFails | read-only | current | Number of sector read-or-writes failures for the SD-CARD. |
| 1.3.6.1.4.1.33283.1.30.8.16 | ScalarsdsSDCARDinitAttempts | read-only | current | Number of attempts to initialize and mount, of the SD-CARD. |
| 1.3.6.1.4.1.33283.1.30.8.17 | ScalarsdsSDCARDinitFailedAttempts | read-only | current | Number of failed attempts to mount the SD-CARD. |
| 1.3.6.1.4.1.33283.1.30.8.80 | ScalarsdsCustomVarString1 | read-only | current | SDS custom string. |
| 1.3.6.1.4.1.33283.1.30.8.81 | ScalarsdsCustomVarString2 | read-only | current | SDS custom string. |
| 1.3.6.1.4.1.33283.1.30.8.82 | ScalarsdsCustomVarString3 | read-only | current | SDS custom string. |
| 1.3.6.1.4.1.33283.1.30.8.83 | ScalarsdsCustomVarString4 | read-only | current | SDS custom string. |
| 1.3.6.1.4.1.33283.1.30.8.84 | ScalarsdsCustomVarString5 | read-only | current | SDS custom string. |
| 1.3.6.1.4.1.33283.1.30.8.90 | ScalarsdsFULLCrunStatus | read-only | current | Actual state of the FULL-C program. |
| 1.3.6.1.4.1.33283.1.30.9 | TablesdsS0Table | not-accessible | current | A list of S0 impulse inputs. |
| 1.3.6.1.4.1.33283.1.30.9.1 | RowsdsS0Entry | not-accessible | current | An entry containing information applicable to a particular S0 input. |
| 1.3.6.1.4.1.33283.1.30.9.1.1 | ColumnsdsS0impCountT0 | read-only | current | Actual S0 impulse counter value for the tarif state T0 (no tarif signal). |
| 1.3.6.1.4.1.33283.1.30.9.1.2 | ColumnsdsS0impCountT1 | read-only | current | Actual S0 impulse counter value for the tarif state T1 (active tarif signal). |
| 1.3.6.1.4.1.33283.1.30.9.1.3 | ColumnsdsS0impMoneyOffsetT0 | read-only | current | Offset (impulse count) for cash calculation. Cash value is calculated relatively starting at this offset, for the T0 counter. |
| 1.3.6.1.4.1.33283.1.30.9.1.4 | ColumnsdsS0impMoneyOffsetT1 | read-only | current | Offset (impulse count) for cash calculation. Cash value is calculated relatively starting at this offset, for the T1 counter. |
| 1.3.6.1.4.1.33283.1.30.9.1.5 | ColumnsdsS0constant | read-only | current | S0 output constant (number of impulses for 1 energy unit). |
| 1.3.6.1.4.1.33283.1.30.9.1.6 | ColumnsdsS0translatedUnitT0 | read-only | current | T0 related S0 impulse count value, recalculated into energy units, in a textual representation. |
| 1.3.6.1.4.1.33283.1.30.9.1.7 | ColumnsdsS0translatedUnitT1 | read-only | current | T1 related S0 impulse count value, recalculated into energy units, in a textual representation. |
| 1.3.6.1.4.1.33283.1.30.9.1.8 | ColumnsdsS0translatedCashT0 | read-only | current | T0 related S0 counter value recalculated into cash (total: T0_impulse_count minus T0_custom_offset), in a textual representation. |
| 1.3.6.1.4.1.33283.1.30.9.1.9 | ColumnsdsS0translatedCashT1 | read-only | current | T1 related S0 counter value recalculated into cash (total: T1_impulse_count minus T1_custom_offset), in a textual representation. |
| 1.3.6.1.4.1.33283.1.30.9.1.10 | ColumnsdsS0actualEnergyFlow | read-only | current | S0: the actual energy flow value. |
| 1.3.6.1.4.1.33283.1.30.9.1.11 | ColumnsdsS0constantMTD | read-only | current | Configuration: the MTD constant. |
| 1.3.6.1.4.1.33283.1.30.9.1.12 | ColumnsdsS0tableRowIndex | not-accessible | current | S0 table row index. |
| 1.3.6.1.4.1.33283.1.30.10 | TablesdsFCsharedVarsTable1 | not-accessible | current | FULL-C SHARED variables. Be careful about the offset in indexes. |
| 1.3.6.1.4.1.33283.1.30.10 | TablesdsFCsharedVarsTable2 | not-accessible | current | FULL-C SHARED variables. Be careful about the offset in indexes. |
| 1.3.6.1.4.1.33283.1.30.10 | TablesdsFCsharedVarsTable3 | not-accessible | current | FULL-C SHARED variables. Be careful about the offset in indexes. |
| 1.3.6.1.4.1.33283.1.30.10 | TablesdsFCsharedVarsTable4 | not-accessible | current | FULL-C SHARED variables. Be careful about the offset in indexes. |
| 1.3.6.1.4.1.33283.1.30.10.1 | RowsdsFCSentry1 | not-accessible | current | Sxx entry. |
| 1.3.6.1.4.1.33283.1.30.10.1.1 | ColumnsdsFC_Sxx | read-only | current | Actual Sxx value. |
| 1.3.6.1.4.1.33283.1.30.10.2 | RowsdsFCSentry2 | not-accessible | current | Uxx entry. |
| 1.3.6.1.4.1.33283.1.30.10.2.1 | ColumnsdsFC_Uxx | read-only | current | Actual Uxx value. |
| 1.3.6.1.4.1.33283.1.30.10.3 | RowsdsFCSentry3 | not-accessible | current | Fxx entry. |
| 1.3.6.1.4.1.33283.1.30.10.3.1 | ColumnsdsFC_Fxx | read-only | current | Actual Fxx value. |
| 1.3.6.1.4.1.33283.1.30.10.4 | RowsdsFCSentry4 | not-accessible | current | Txx entry. |
| 1.3.6.1.4.1.33283.1.30.10.4.1 | ColumnsdsFC_Txx | read-only | current | Actual Txx value. |
| 1.3.6.1.4.1.33283.1.30.11 | NodesdsSerialPortsEntry | |||
| 1.3.6.1.4.1.33283.1.30.11.1 | NodesdsPortCOM1Entry | |||
| 1.3.6.1.4.1.33283.1.30.11.1.1 | ScalarsdsCOM1telnetConnected | read-only | current | COM1: Is there any Ethernet client connected and using the Eth-to-Serial converter, at this moment. |
| 1.3.6.1.4.1.33283.1.30.11.1.2 | ScalarsdsCOM1baudrate | read-only | current | COM1: Actual configured UART baud rate in [bps]. |
| 1.3.6.1.4.1.33283.1.30.11.1.3 | ScalarsdsCOM1dataSize | read-only | current | COM1: Actual configured UART char data size [8 or 9 bits per char]. |
| 1.3.6.1.4.1.33283.1.30.11.1.4 | ScalarsdsCOM1stopBits | read-only | current | COM1: Actual configured UART number of stop bits [1 or 2 stop bits] |
| 1.3.6.1.4.1.33283.1.30.11.1.5 | ScalarsdsCOM1parity | read-only | current | COM1: Actual configured UART parity. |
| 1.3.6.1.4.1.33283.1.30.11.1.6 | ScalarsdsCOM1uartInBytes | read-only | current | COM1: Total number of UART IN bytes. |
| 1.3.6.1.4.1.33283.1.30.11.1.7 | ScalarsdsCOM1uartOutBytes | read-only | current | COM1: Total number of UART OUT bytes. |
| 1.3.6.1.4.1.33283.1.30.11.6 | NodesdsPortCOM6Entry | |||
| 1.3.6.1.4.1.33283.1.30.11.6.1 | ScalarsdsCOM6telnetConnected | read-only | current | COM6: Is there any Ethernet client connected and using the Eth-to-Serial converter, at this moment. |
| 1.3.6.1.4.1.33283.1.30.11.6.2 | ScalarsdsCOM6baudrate | read-only | current | COM6: Actual configured UART baud rate in [bps]. |
| 1.3.6.1.4.1.33283.1.30.11.6.3 | ScalarsdsCOM6dataSize | read-only | current | COM6: Actual configured UART char data size [8 or 9 bits per char]. |
| 1.3.6.1.4.1.33283.1.30.11.6.4 | ScalarsdsCOM6stopBits | read-only | current | COM6: Actual configured UART number of stop bits [1 or 2 stop bits] |
| 1.3.6.1.4.1.33283.1.30.11.6.5 | ScalarsdsCOM6parity | read-only | current | COM6: Actual configured UART parity. |
| 1.3.6.1.4.1.33283.1.30.11.6.6 | ScalarsdsCOM6uartInBytes | read-only | current | COM6: Total number of UART IN bytes. |
| 1.3.6.1.4.1.33283.1.30.11.6.7 | ScalarsdsCOM6uartOutBytes | read-only | current | COM6: Total number of UART OUT bytes. |
| 1.3.6.1.4.1.33283.70 | NodeipwActive-trap | TRAP: The current IP watchdog status. | ||
| 1.3.6.1.4.1.33283.71 | NodeipwPingIP-trap | TRAP: IP address of the wdg monitored object. | ||
| 1.3.6.1.4.1.33283.72 | NodeipwPauseAfterPwOn-trap | TRAP: Duration of the IP watchdog disable period. | ||
| 1.3.6.1.4.1.33283.73 | NodeipwPingTimeout-trap | TRAP: IP watchdog RTT timeout. | ||
| 1.3.6.1.4.1.33283.74 | NodeipwRepeatPingPer-trap | TRAP: IP watchdog send repeat period. | ||
| 1.3.6.1.4.1.33283.75 | NodeipwIgnoreLostCnt-trap | TRAP: IP watchdog: number of missing packets to ignore. | ||
| 1.3.6.1.4.1.33283.76 | NodeipwPauseWdAfterAct-trap | TRAP: IP watchog pause applied after output activation. | ||
| 1.3.6.1.4.1.33283.77 | NodeipwRelayActTime-trap | TRAP: Length of IP watchdog notification output active state. | ||
| 1.3.6.1.4.1.33283.78 | NodeipwActualFailed-trap | TRAP: number of missing IP watchdog ping responses. | ||
| 1.3.6.1.4.1.33283.79 | NodeipwLastRTT-trap | TRAP: IP watchdog Round Trip Time for the last ping echo. | ||
| 1.3.6.1.4.1.33283.80 | NodeipwActualRelayState-trap | TRAP: Actual (virtual) output relay status of IP watchdog. | ||
| 1.3.6.1.4.1.33283.100 | Nodeopto1-trap | TRAP: optical input 1 status. | ||
| 1.3.6.1.4.1.33283.101 | Nodeopto2-trap | TRAP: optical input 2 status. | ||
| 1.3.6.1.4.1.33283.102 | Nodeopto3-trap | TRAP: optical input 3 status. | ||
| 1.3.6.1.4.1.33283.103 | Nodeopto4-trap | TRAP: optical input 4 status. | ||
| 1.3.6.1.4.1.33283.104 | Nodeopto5-trap | TRAP: optical input 5 status. | ||
| 1.3.6.1.4.1.33283.105 | Nodeopto6-trap | TRAP: optical input 6 status. | ||
| 1.3.6.1.4.1.33283.106 | Nodeopto7-trap | TRAP: optical input 7 status. | ||
| 1.3.6.1.4.1.33283.107 | Nodeopto8-trap | TRAP: optical input 8 status. | ||
| 1.3.6.1.4.1.33283.108 | Nodelogics0input-trap | TRAP: LOGIC-S0 input status. | ||
| 1.3.6.1.4.1.33283.150 | NodesdsRE1state-trap | TRAP: Current RELAY 1 output status. | ||
| 1.3.6.1.4.1.33283.151 | NodesdsRE1cby-trap | TRAP: RELAY 1 controled by ... | ||
| 1.3.6.1.4.1.33283.152 | NodesdsRE1name-trap | TRAP: User name for RELAY 1. | ||
| 1.3.6.1.4.1.33283.153 | NodesdsRE2state-trap | TRAP: Current RELAY 2 output status. | ||
| 1.3.6.1.4.1.33283.154 | NodesdsRE2cby-trap | TRAP: RELAY 2 controled by ... | ||
| 1.3.6.1.4.1.33283.155 | NodesdsRE2name-trap | TRAP: User name for RELAY 2. | ||
| 1.3.6.1.4.1.33283.156 | NodesdsRE3state-trap | TRAP: Current RELAY 3 output status. | ||
| 1.3.6.1.4.1.33283.157 | NodesdsRE3cby-trap | TRAP: RELAY 3 controled by ... | ||
| 1.3.6.1.4.1.33283.158 | NodesdsRE3name-trap | TRAP: User name for RELAY 3. | ||
| 1.3.6.1.4.1.33283.159 | NodesdsRE4state-trap | TRAP: Current RELAY 4 output status. | ||
| 1.3.6.1.4.1.33283.160 | NodesdsRE4cby-trap | TRAP: RELAY 4 controled by ... | ||
| 1.3.6.1.4.1.33283.161 | NodesdsRE4name-trap | TRAP: User name for RELAY 4. | ||
| 1.3.6.1.4.1.33283.162 | NodesdsRE5state-trap | TRAP: Current RELAY 5 output status. | ||
| 1.3.6.1.4.1.33283.163 | NodesdsRE5cby-trap | TRAP: RELAY 5 controled by ... | ||
| 1.3.6.1.4.1.33283.164 | NodesdsRE5name-trap | TRAP: User name for RELAY 5. | ||
| 1.3.6.1.4.1.33283.165 | NodesdsRE6state-trap | TRAP: Current RELAY 6 output status. | ||
| 1.3.6.1.4.1.33283.166 | NodesdsRE6cby-trap | TRAP: RELAY 6 controled by ... | ||
| 1.3.6.1.4.1.33283.167 | NodesdsRE6name-trap | TRAP: User name for RELAY 6. | ||
| 1.3.6.1.4.1.33283.200 | NodesdsPWM1freq-trap | TRAP: Actual PWM1 generator frequency [Hz]. | ||
| 1.3.6.1.4.1.33283.201 | NodesdsPWM1duty-trap | TRAP: Actual PWM1 duty control setting. | ||
| 1.3.6.1.4.1.33283.220 | NodesdsADCrawValue0-trap | TRAP: Actual analog input value [raw]. | ||
| 1.3.6.1.4.1.33283.221 | NodesdsADCtext0-trap | TRAP: Textual conversion output for analog input. | ||
| 1.3.6.1.4.1.33283.222 | NodesdsADCintmul0-trap | TRAP: SI integer MUL value for the analog input (conversion result multiplied by 100). | ||
| 1.3.6.1.4.1.33283.223 | NodesdsADCname0-trap | TRAP: User name for analog input. | ||
| 1.3.6.1.4.1.33283.224 | NodesdsADCrawValue1-trap | TRAP: Actual analog input value [raw]. | ||
| 1.3.6.1.4.1.33283.225 | NodesdsADCtext1-trap | TRAP: Textual conversion output for analog input. | ||
| 1.3.6.1.4.1.33283.226 | NodesdsADCintmul1-trap | TRAP: SI integer MUL value for the analog input (conversion result multiplied by 100). | ||
| 1.3.6.1.4.1.33283.227 | NodesdsADCname1-trap | TRAP: User name for analog input. | ||
| 1.3.6.1.4.1.33283.228 | NodesdsADCrawValue2-trap | TRAP: Actual analog input value [raw]. | ||
| 1.3.6.1.4.1.33283.229 | NodesdsADCtext2-trap | TRAP: Textual conversion output for analog input. | ||
| 1.3.6.1.4.1.33283.230 | NodesdsADCintmul2-trap | TRAP: SI integer MUL value for the analog input (conversion result multiplied by 100). | ||
| 1.3.6.1.4.1.33283.231 | NodesdsADCname2-trap | TRAP: User name for analog input. | ||
| 1.3.6.1.4.1.33283.232 | NodesdsADCrawValue3-trap | TRAP: Actual analog input value [raw]. | ||
| 1.3.6.1.4.1.33283.233 | NodesdsADCtext3-trap | TRAP: Textual conversion output for analog input. | ||
| 1.3.6.1.4.1.33283.234 | NodesdsADCintmul3-trap | TRAP: SI integer MUL value for the analog input (conversion result multiplied by 100). | ||
| 1.3.6.1.4.1.33283.235 | NodesdsADCname3-trap | TRAP: User name for analog input. | ||
| 1.3.6.1.4.1.33283.236 | NodesdsADCrawValue4-trap | TRAP: Actual analog input value [raw]. | ||
| 1.3.6.1.4.1.33283.237 | NodesdsADCtext4-trap | TRAP: Textual conversion output for analog input. | ||
| 1.3.6.1.4.1.33283.238 | NodesdsADCintmul4-trap | TRAP: SI integer MUL value for the analog input (conversion result multiplied by 100). | ||
| 1.3.6.1.4.1.33283.239 | NodesdsADCname4-trap | TRAP: User name for analog input. | ||
| 1.3.6.1.4.1.33283.240 | NodesdsADCrawValue5-trap | TRAP: Actual analog input value [raw]. | ||
| 1.3.6.1.4.1.33283.241 | NodesdsADCtext5-trap | TRAP: Textual conversion output for analog input. | ||
| 1.3.6.1.4.1.33283.242 | NodesdsADCintmul5-trap | TRAP: SI integer MUL value for the analog input (conversion result multiplied by 100). | ||
| 1.3.6.1.4.1.33283.243 | NodesdsADCname5-trap | TRAP: User name for analog input. | ||
| 1.3.6.1.4.1.33283.244 | NodesdsADCrawValue6-trap | TRAP: Actual analog input value [raw]. | ||
| 1.3.6.1.4.1.33283.245 | NodesdsADCtext6-trap | TRAP: Textual conversion output for analog input. | ||
| 1.3.6.1.4.1.33283.246 | NodesdsADCintmul6-trap | TRAP: SI integer MUL value for the analog input (conversion result multiplied by 100). | ||
| 1.3.6.1.4.1.33283.247 | NodesdsADCname6-trap | TRAP: User name for analog input. | ||
| 1.3.6.1.4.1.33283.248 | NodesdsADCrawValue7-trap | TRAP: Actual analog input value [raw]. | ||
| 1.3.6.1.4.1.33283.249 | NodesdsADCtext7-trap | TRAP: Textual conversion output for analog input. | ||
| 1.3.6.1.4.1.33283.250 | NodesdsADCintmul7-trap | TRAP: SI integer MUL value for the analog input (conversion result multiplied by 100). | ||
| 1.3.6.1.4.1.33283.251 | NodesdsADCname7-trap | TRAP: User name for analog input. | ||
| 1.3.6.1.4.1.33283.301 | NodesdsOneWireStatus-trap | TRAP: 1-WIRE device status. INFO: USE INDEX OID TO ACCESS THE TABLE ITEMS. | ||
| 1.3.6.1.4.1.33283.302 | NodesdsOneWireDeviceROMcode-trap | TRAP: 1-WIRE device ROM-CODE. INFO: USE INDEX OID TO ACCESS THE TABLE ITEMS. | ||
| 1.3.6.1.4.1.33283.303 | NodesdsOneWireName-trap | TRAP: 1-WIRE device name. INFO: USE INDEX OID TO ACCESS THE TABLE ITEMS. | ||
| 1.3.6.1.4.1.33283.304 | NodesdsOneWireFullValIDX0-trap | TRAP: First value received from 1-WIRE device. INFO: USE INDEX OID TO ACCESS THE TABLE ITEMS. | ||
| 1.3.6.1.4.1.33283.305 | NodesdsOneWireFullValIDX1-trap | TRAP: Second value received from 1-WIRE device. INFO: USE INDEX OID TO ACCESS THE TABLE ITEMS. | ||
| 1.3.6.1.4.1.33283.306 | NodesdsOneWireConfigFlags-trap | TRAP: 1-WIRE device user-configuration. INFO: USE INDEX OID TO ACCESS THE TABLE ITEMS. | ||
| 1.3.6.1.4.1.33283.400 | NodesdsVersionText-trap | TRAP: SDS device version text. | ||
| 1.3.6.1.4.1.33283.401 | NodesdsCustomVarTrap1-trap | TRAP: SDS custom-trap value. | ||
| 1.3.6.1.4.1.33283.402 | NodesdsCustomVarTrap2-trap | TRAP: SDS custom-trap value. | ||
| 1.3.6.1.4.1.33283.403 | NodesdsCustomVarTrap3-trap | TRAP: SDS custom-trap value. | ||
| 1.3.6.1.4.1.33283.404 | NodesdsCustomVarTrap4-trap | TRAP: SDS custom-trap value. | ||
| 1.3.6.1.4.1.33283.405 | NodesdsCustomVarTrap5-trap | TRAP: SDS custom-trap value. | ||
| 1.3.6.1.4.1.33283.406 | NodesdsCustomVarTrap6-trap | TRAP: SDS custom-trap value. | ||
| 1.3.6.1.4.1.33283.407 | NodesdsCustomVarTrap7-trap | TRAP: SDS custom-trap value. | ||
| 1.3.6.1.4.1.33283.408 | NodesdsCustomVarTrap8-trap | TRAP: SDS custom-trap value. | ||
| 1.3.6.1.4.1.33283.409 | NodesdsCustomVarTrap9-trap | TRAP: SDS custom-trap value. | ||
| 1.3.6.1.4.1.33283.501 | NodesdsS0impCountT0-trap | TRAP: Actual S0 impulse counter value for T0 tarif. INFO: USE INDEX OID TO ACCESS THE TABLE ITEMS. | ||
| 1.3.6.1.4.1.33283.502 | NodesdsS0impCountT1-trap | TRAP: Actual S0 impulse counter value for T1 tarif. INFO: USE INDEX OID TO ACCESS THE TABLE ITEMS. | ||
| 1.3.6.1.4.1.33283.503 | NodesdsS0impMoneyOffsetT0-trap | TRAP: Offset (impulse count) for cash calculation for T0. INFO: USE INDEX OID TO ACCESS THE TABLE ITEMS. | ||
| 1.3.6.1.4.1.33283.504 | NodesdsS0impMoneyOffsetT1-trap | TRAP: Offset (impulse count) for cash calculation for T1. INFO: USE INDEX OID TO ACCESS THE TABLE ITEMS. | ||
| 1.3.6.1.4.1.33283.505 | NodesdsS0constant-trap | TRAP: S0 output constant (number of impulses for 1 energy unit). INFO: USE INDEX OID TO ACCESS THE TABLE ITEMS. | ||
| 1.3.6.1.4.1.33283.506 | NodesdsS0translatedUnitT0-trap | TRAP: T0 related S0 impulse count value as textual energy unit. INFO: USE INDEX OID TO ACCESS THE TABLE ITEMS. | ||
| 1.3.6.1.4.1.33283.507 | NodesdsS0translatedUnitT1-trap | TRAP: T1 related S0 impulse count value as textual energy unit. INFO: USE INDEX OID TO ACCESS THE TABLE ITEMS. | ||
| 1.3.6.1.4.1.33283.508 | NodesdsS0translatedCashT0-trap | TRAP: T0 related S0 counter value as textual cash value. INFO: USE INDEX OID TO ACCESS THE TABLE ITEMS. | ||
| 1.3.6.1.4.1.33283.509 | NodesdsS0translatedCashT1-trap | TRAP: T1 related S0 counter value as textual cash value. INFO: USE INDEX OID TO ACCESS THE TABLE ITEMS. | ||
| 1.3.6.1.4.1.33283.510 | NodesdsS0actualEnergyFlow-trap | TRAP: S0: the actual energy flow value. INFO: USE INDEX OID TO ACCESS THE TABLE ITEMS. | ||
| 1.3.6.1.4.1.33283.511 | NodesdsS0constantMTD-trap | TRAP: S0: configuration - the MTD constant. INFO: USE INDEX OID TO ACCESS THE TABLE ITEMS. | ||
| 1.3.6.1.4.1.33283.600 | NodesdsNTPvalue-trap | TRAP: Actual NTP time value (SDS device is NTP client). | ||
| 1.3.6.1.4.1.33283.601 | NodesdsSoCtempValue-trap | TRAP: Actual SoC chip internal temperature, in special units. | ||
| 1.3.6.1.4.1.33283.602 | NodesdsOneWireBUSAcountValue-trap | TRAP: Number of discovered 1-Wire devices on BUS A. | ||
| 1.3.6.1.4.1.33283.603 | NodesdsOneWireBUSBcountValue-trap | TRAP: Number of discovered 1-Wire devices on BUS B. | ||
| 1.3.6.1.4.1.33283.604 | NodesdsGPIOTOPBOARDoutputState-trap | TRAP: GPIO-TOPBOARD actual in-out value. | ||
| 1.3.6.1.4.1.33283.605 | NodesdsGPIOTOPBOARDdirection-trap | TRAP: GPIO-TOPBOARD actual direction (in-out) status. | ||
| 1.3.6.1.4.1.33283.606 | NodesdsBackUpCoinBatteryVoltageValue-trap | TRAP: Actual voltage reading of the back-up coin battery. | ||
| 1.3.6.1.4.1.33283.680 | NodesdsCustomVarString1-trap | TRAP: Custom String. | ||
| 1.3.6.1.4.1.33283.681 | NodesdsCustomVarString2-trap | TRAP: Custom String. | ||
| 1.3.6.1.4.1.33283.682 | NodesdsCustomVarString3-trap | TRAP: Custom String. | ||
| 1.3.6.1.4.1.33283.683 | NodesdsCustomVarString4-trap | TRAP: Custom String. | ||
| 1.3.6.1.4.1.33283.684 | NodesdsCustomVarString5-trap | TRAP: Custom String. | ||
| 1.3.6.1.4.1.33283.690 | NodesdsFULLCrunStatus-trap | TRAP: FULL-C program status. | ||
| 1.3.6.1.4.1.33283.800 | NodesdsCOM1telnetConnected-trap | TRAP: COM1: Is any Ethernet client connected to Eth-to-Serial converter. | ||
| 1.3.6.1.4.1.33283.801 | NodesdsCOM1baudrate-trap | TRAP: COM1: Actual configured UART baud rate in [bps]. | ||
| 1.3.6.1.4.1.33283.802 | NodesdsCOM1dataSize-trap | TRAP: COM1: Actual configured UART char data size [num of bits]. | ||
| 1.3.6.1.4.1.33283.803 | NodesdsCOM1stopBits-trap | TRAP: COM1: Actual configured UART number of stop bits. | ||
| 1.3.6.1.4.1.33283.804 | NodesdsCOM1parity-trap | TRAP: COM1: Actual configured UART parity. | ||
| 1.3.6.1.4.1.33283.805 | NodesdsCOM1uartInBytes-trap | TRAP: COM1: Total number of UART IN bytes. | ||
| 1.3.6.1.4.1.33283.806 | NodesdsCOM1uartOutBytes-trap | TRAP: COM1: Total number of UART OUT bytes. | ||
| 1.3.6.1.4.1.33283.850 | NodesdsCOM6telnetConnected-trap | TRAP: COM6: Is any Ethernet client connected to Eth-to-Serial converter. | ||
| 1.3.6.1.4.1.33283.851 | NodesdsCOM6baudrate-trap | TRAP: COM6: Actual configured UART baud rate in [bps]. | ||
| 1.3.6.1.4.1.33283.852 | NodesdsCOM6dataSize-trap | TRAP: COM6: Actual configured UART char data size [num of bits]. | ||
| 1.3.6.1.4.1.33283.853 | NodesdsCOM6stopBits-trap | TRAP: COM6: Actual configured UART number of stop bits. | ||
| 1.3.6.1.4.1.33283.854 | NodesdsCOM6parity-trap | TRAP: COM6: Actual configured UART parity. | ||
| 1.3.6.1.4.1.33283.855 | NodesdsCOM6uartInBytes-trap | TRAP: COM1: Total number of UART IN bytes. | ||
| 1.3.6.1.4.1.33283.856 | NodesdsCOM6uartOutBytes-trap | TRAP: COM6: Total number of UART OUT bytes. |