SENCORE-MRD2600-MIB
597 objects
Receiver decoder object and event definitions.
Imported Objects
| INET-ADDRESS-MIB | InetAddress InetAddressType InetPortNumber |
| SENCORE-CSP-MIB | Condition |
| SENCORE-GLOBAL-REG | sencoreProducts |
| SNMPv2-CONF | OBJECT-GROUP |
| SNMPv2-SMI | Integer32 IpAddress MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DateAndTime MacAddress RowStatus TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9986.3.23 | Identitymrd2600MibModule | Receiver decoder object and event definitions. | ||
| 1.3.6.1.4.1.9986.3.23.1 | NodemrdObjs | |||
| 1.3.6.1.4.1.9986.3.23.1.1 | NodeunitObjs | |||
| 1.3.6.1.4.1.9986.3.23.1.1.1 | TableplatformTable | not-accessible | current | Platform table. |
| 1.3.6.1.4.1.9986.3.23.1.1.1.1 | RowplatformEntry | not-accessible | current | Platform entry. |
| 1.3.6.1.4.1.9986.3.23.1.1.1.1.1 | ColumnplatformIndex | not-accessible | current | The index number of the platform (1). |
| 1.3.6.1.4.1.9986.3.23.1.1.1.1.2 | ColumnplatformLocation | read-only | current | This is a dummy value allowing for the platformIndex value to exist. |
| 1.3.6.1.4.1.9986.3.23.1.1.2 | TablempegipcardTable | not-accessible | current | MPEG/IP Card table. |
| 1.3.6.1.4.1.9986.3.23.1.1.2.1 | RowmpegipcardEntry | not-accessible | current | MPEG/IP Card entry. |
| 1.3.6.1.4.1.9986.3.23.1.1.2.1.1 | ColumnmpegipcardDefaultGateway | read-write | current | Configures preferred gateway to use. |
| 1.3.6.1.4.1.9986.3.23.1.1.2.1.2 | ColumnmpegipcardIcmpResponse | read-write | current | Enables/Disables response to ping (ICMP]. |
| 1.3.6.1.4.1.9986.3.23.1.1.3 | TablempegipnicTable | not-accessible | current | MPEG/IP Port table. |
| 1.3.6.1.4.1.9986.3.23.1.1.3.1 | RowmpegipnicEntry | not-accessible | current | MPEG/IP Port entry. |
| 1.3.6.1.4.1.9986.3.23.1.1.3.1.1 | ColumnmpegipnicIndex | not-accessible | current | Identifies an Port interface. |
| 1.3.6.1.4.1.9986.3.23.1.1.3.1.2 | ColumnmpegipnicIpAddrType | read-only | current | The the type of Internet address of the Port. At this time, only IPv4 is supported. |
| 1.3.6.1.4.1.9986.3.23.1.1.3.1.3 | ColumnmpegipnicIpAddr | read-write | current | Configures the IP address for the Port.Octets in Hex format example: 10.0.10.49 enter as <#0x0A 0x00 0x0A 0x31> |
| 1.3.6.1.4.1.9986.3.23.1.1.3.1.4 | ColumnmpegipnicSubnetMaskType | read-only | current | The the type of Internet address for the subnet mask of the Port. At this time, only IPv4 is supported. |
| 1.3.6.1.4.1.9986.3.23.1.1.3.1.5 | ColumnmpegipnicSubnetMask | read-write | current | Configures subnet mask for the Port. |
| 1.3.6.1.4.1.9986.3.23.1.1.3.1.6 | ColumnmpegipnicGatewayType | read-only | current | The the type of Internet address of the Port gateway. At this time, only IPv4 is supported. |
| 1.3.6.1.4.1.9986.3.23.1.1.3.1.7 | ColumnmpegipnicGateway | read-write | current | Configures Gateway address for the Port. |
| 1.3.6.1.4.1.9986.3.23.1.1.3.1.8 | ColumnmpegipnicLinkSpeed | read-write | current | Configures the link speed of the Port. |
| 1.3.6.1.4.1.9986.3.23.1.1.3.1.9 | ColumnmpegipnicMACAddr | read-only | current | Shows MAC address of the Port. |
| 1.3.6.1.4.1.9986.3.23.1.1.3.1.10 | ColumnmpegipnicLinkStatus | read-only | current | Shows link status of the Port. |
| 1.3.6.1.4.1.9986.3.23.1.1.3.1.11 | ColumnmpegipnicLinkSpeedStatus | read-only | current | Shows link speed status of the Port. |
| 1.3.6.1.4.1.9986.3.23.1.1.3.1.12 | ColumnmpegipnicIgmpVersion | read-only | current | Shows the IGMP mode. |
| 1.3.6.1.4.1.9986.3.23.1.1.3.1.13 | ColumnmpegipnicAggTxBitrate | read-only | current | Shows the aggregate IP transmission bitrate. |
| 1.3.6.1.4.1.9986.3.23.1.1.3.1.14 | ColumnmpegipnicAggRxBitrate | read-only | current | Shows the aggregate IP receive bitrate. |
| 1.3.6.1.4.1.9986.3.23.1.1.3.1.15 | ColumnmpegipnicLinkLossCond | read-only | current | Link Loss Error |
| 1.3.6.1.4.1.9986.3.23.1.1.4 | NodesystemObjs | |||
| 1.3.6.1.4.1.9986.3.23.1.1.4.1 | ScalarunitAlias | read-write | current | A string used to easily identify the unit. |
| 1.3.6.1.4.1.9986.3.23.1.1.4.2 | ScalarunitSerialNum | read-only | current | Shows a Serial Number to uniquely identify the unit. |
| 1.3.6.1.4.1.9986.3.23.1.1.4.3 | ScalarsystemState | read-only | current | Shows the State of the System. |
| 1.3.6.1.4.1.9986.3.23.1.1.4.4 | ScalarunitUidLed | read-write | current | Turns on and off the unit identifier LED to help identify a specific unit in a rack of units. |
| 1.3.6.1.4.1.9986.3.23.1.1.4.5 | ScalarunitPowerSupply | read-only | current | A string used to easily identify the unit. |
| 1.3.6.1.4.1.9986.3.23.1.1.5 | NodepowersupplyObjs | |||
| 1.3.6.1.4.1.9986.3.23.1.1.5.1 | ScalarpowersupplyError | read-only | current | A status of outOfCondition(1) means the power supply is operational. A status of inCondition(2) means the power supply is not operational. |
| 1.3.6.1.4.1.9986.3.23.1.1.5.2 | TablepowersupplyTable | not-accessible | current | Power Supply Table |
| 1.3.6.1.4.1.9986.3.23.1.1.5.2.1 | RowpowersupplyEntry | not-accessible | current | Power Supply Entry |
| 1.3.6.1.4.1.9986.3.23.1.1.5.2.1.1 | ColumnpowersupplyPsuIndex | not-accessible | current | Identifies the power supply. Power supply 1 is index 1 and power supply 2 is index 2. |
| 1.3.6.1.4.1.9986.3.23.1.1.5.2.1.2 | ColumnpowersupplyPsuStatus | read-only | current | A status of enabled(1) means the power supply is in working condition. A status of disabled(2) means the power supply is in an error state. |
| 1.3.6.1.4.1.9986.3.23.1.1.6 | NodecontrolportObjs | |||
| 1.3.6.1.4.1.9986.3.23.1.1.6.1 | TablecontrolportlistTable | not-accessible | current | Control port configuration table for MPEG/IP cards. |
| 1.3.6.1.4.1.9986.3.23.1.1.6.1.1 | RowcontrolportlistEntry | not-accessible | current | Control port configuration entry for MPEG/IP cards. |
| 1.3.6.1.4.1.9986.3.23.1.1.6.1.1.1 | ColumncontrolportlistLabel | read-only | current | Configures the traffic control mode of the control port. |
| 1.3.6.1.4.1.9986.3.23.1.1.6.1.1.2 | ColumncontrolportlistId | read-only | current | Shows the ID of the port used as the second control port. |
| 1.3.6.1.4.1.9986.3.23.1.1.6.2 | ScalarcontrolportnicSelectedPort | read-write | current | Identifies the port location of the control port. The control port is chosen from instances of controlportlistId MIB object. |
| 1.3.6.1.4.1.9986.3.23.1.1.6.3 | ScalarcontrolportnicDefaultGateway | read-write | current | Selection of the default gateway. |
| 1.3.6.1.4.1.9986.3.23.1.1.6.4 | ScalarcontrolportnicIpMode | read-only | current | Current mode the control port uses to get an IP address. |
| 1.3.6.1.4.1.9986.3.23.1.1.6.5 | ScalarcontrolportnicMacAddress | read-only | current | MAC address of the control port. |
| 1.3.6.1.4.1.9986.3.23.1.1.6.6 | ScalarcontrolportnicIpAddress | read-only | current | Current IP address of the control port. |
| 1.3.6.1.4.1.9986.3.23.1.1.6.7 | ScalarcontrolportnicNetmask | read-only | current | Current subnet mask of the control port. |
| 1.3.6.1.4.1.9986.3.23.1.1.6.8 | ScalarcontrolportnicGateway | read-only | current | Current gateway of the control port. |
| 1.3.6.1.4.1.9986.3.23.1.1.6.9 | ScalarcontrolportnicNewIpMode | read-write | current | See controlportnicApplyNew |
| 1.3.6.1.4.1.9986.3.23.1.1.6.10 | ScalarcontrolportnicNewIpAddress | read-write | current | See controlportnicApplyNew |
| 1.3.6.1.4.1.9986.3.23.1.1.6.11 | ScalarcontrolportnicNewNetmask | read-write | current | See controlportnicApplyNew |
| 1.3.6.1.4.1.9986.3.23.1.1.6.12 | ScalarcontrolportnicNewGateway | read-write | current | See controlportnicApplyNew |
| 1.3.6.1.4.1.9986.3.23.1.1.6.13 | ScalarcontrolportnicApplyNew | read-write | current | IpAddress, Netmask, and Gateway must all be set at once when switching to static mode. To do this, set controlportnicNewIpAddress, controlportnicNewNetmask, an… |
| 1.3.6.1.4.1.9986.3.23.1.1.7 | Tabledvbs2xportTable | not-accessible | current | DVB-S2X Port Table. |
| 1.3.6.1.4.1.9986.3.23.1.1.7.1 | Rowdvbs2xportEntry | not-accessible | current | DVB-S2X Port Entry. |
| 1.3.6.1.4.1.9986.3.23.1.1.7.1.1 | Columndvbs2xportIndex | not-accessible | current | Identifies a DVB-S2X port. |
| 1.3.6.1.4.1.9986.3.23.1.1.7.1.2 | Columndvbs2xportLnbPower | read-write | current | Configures the LNB voltage for the DVB-S2X port. |
| 1.3.6.1.4.1.9986.3.23.1.1.7.1.3 | Columndvbs2xport22KhzToneState | read-write | current | Configures the enabled state of the 22 kHz for tone for the port. This setting is only applied when the LNB Power is enabled. |
| 1.3.6.1.4.1.9986.3.23.1.1.7.1.4 | Columndvbs2xportLnbPowerUnexpectedVoltage | read-only | current | Indicates that the LNB voltage is out of tolerance. |
| 1.3.6.1.4.1.9986.3.23.1.1.7.1.5 | Columndvbs2xportLnbPowerHighCurrent | read-only | current | Indicates that the LNB power supply has exceeded the current limit. |
| 1.3.6.1.4.1.9986.3.23.1.1.7.1.6 | Columndvbs2xportLnbPowerErrorCond | read-only | current | Indicates that there is an LNB power error condition. |
| 1.3.6.1.4.1.9986.3.23.1.2 | NodeinputObjs | |||
| 1.3.6.1.4.1.9986.3.23.1.2.1 | TabletsinputsrcTable | not-accessible | current | TS input source table. |
| 1.3.6.1.4.1.9986.3.23.1.2.1.1 | RowtsinputsrcEntry | not-accessible | current | TS input source entry. |
| 1.3.6.1.4.1.9986.3.23.1.2.1.1.1 | ColumntsinputsrcType | read-only | current | Identifies an input source by the type of input source. |
| 1.3.6.1.4.1.9986.3.23.1.2.1.1.2 | ColumntsinputsrcSlot | not-accessible | current | Identifies an input by the input slot location. |
| 1.3.6.1.4.1.9986.3.23.1.2.1.1.3 | ColumntsinputsrcIndex | not-accessible | current | Identifies an input source. |
| 1.3.6.1.4.1.9986.3.23.1.2.1.1.4 | ColumntsinputsrcState | read-write | current | Configures the enabled state of the input source. |
| 1.3.6.1.4.1.9986.3.23.1.2.1.1.5 | ColumntsinputsrcLabel | read-only | current | Shows the Label describing the input. |
| 1.3.6.1.4.1.9986.3.23.1.2.1.1.6 | ColumntsinputsrcId | read-only | current | Shows the Id of the input source. |
| 1.3.6.1.4.1.9986.3.23.1.2.1.1.7 | ColumntsinputsrcTsBitrate | read-only | current | Shows the bitrate of the input TS. |
| 1.3.6.1.4.1.9986.3.23.1.2.1.1.8 | ColumntsinputsrcTsSync | read-only | current | Shows the lock status of the transport stream sync. |
| 1.3.6.1.4.1.9986.3.23.1.2.2 | TableinputTable | not-accessible | current | Input table. |
| 1.3.6.1.4.1.9986.3.23.1.2.2.1 | RowinputEntry | not-accessible | current | Input entry. |
| 1.3.6.1.4.1.9986.3.23.1.2.2.1.1 | ColumninputIndex | not-accessible | current | Identifies an input source. |
| 1.3.6.1.4.1.9986.3.23.1.2.2.1.2 | ColumninputPrimarySrc | read-write | current | Configures a primary input source. The input is chosen from instances of tsinputsrcId MIB object. |
| 1.3.6.1.4.1.9986.3.23.1.2.2.1.3 | ColumninputBackupSrc | read-write | current | Configures a backup input source. The input is chosen from instances of tsinputsrcId MIB object. |
| 1.3.6.1.4.1.9986.3.23.1.2.2.1.4 | ColumninputInputActive | read-only | current | Indicates if the primary or backup input is currently the active input. 1 Primary 2 Backup |
| 1.3.6.1.4.1.9986.3.23.1.2.2.1.5 | ColumninputBackupState | read-only | current | Shows the enabled state of the backup input. |
| 1.3.6.1.4.1.9986.3.23.1.2.2.1.6 | ColumninputSwitchOverInterval | read-write | current | Configures the switch-over interval for the input. |
| 1.3.6.1.4.1.9986.3.23.1.2.2.1.7 | ColumninputFailoverTrigger | read-write | current | Configures the trigger for the input fail-over. |
| 1.3.6.1.4.1.9986.3.23.1.2.2.1.8 | ColumninputSrcRestoreTrigger | read-write | current | Configures the restore trigger for the input. |
| 1.3.6.1.4.1.9986.3.23.1.2.2.1.9 | ColumninputManualSwitchover | read-write | current | Commands a switch to Backup or primary input |
| 1.3.6.1.4.1.9986.3.23.1.2.2.1.10 | ColumninputBackupInputActiveCond | read-only | current | Indicates Active Backup condition Out of Condition, Not in Backup state or In Condition, In Backup input state |
| 1.3.6.1.4.1.9986.3.23.1.2.2.1.11 | ColumninputTsNotPresentCond | read-only | current | Transport Stream Not Present |
| 1.3.6.1.4.1.9986.3.23.1.2.2.1.12 | ColumninputTsErroredCond | read-only | current | Transport Error Indicator |
| 1.3.6.1.4.1.9986.3.23.1.2.3 | TablempegiprcvTable | not-accessible | current | MPEG/IP receive table. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1 | RowmpegiprcvEntry | not-accessible | current | MPEG/IP receive entry. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.1 | ColumnmpegiprcvIndex | not-accessible | current | Identifies an MPEG/IP input source. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.2 | ColumnmpegiprcvNic | read-write | current | Configures the connector, when use AG128 or AG26028, Port 1 = Card, Port 2 = Chassis. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.3 | ColumnmpegiprcvStreamMode | read-write | current | Configures the input stream to be multicast or unicast. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.4 | ColumnmpegiprcvDestinationAddressType | read-only | current | The the type of Internet address of the destination when in multicast mode. At this time, only IPv4 is supported. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.5 | ColumnmpegiprcvDestinationIp | read-write | current | Configures the Destination Internet address when in multicast mode. Octets in Hex format example: 239.192.0.200 enter as <#0xEF 0xC0 0x00 0xC8> |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.6 | ColumnmpegiprcvPort | read-write | current | Configures the destination Internet port address for the IP stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.7 | ColumnmpegiprcvNullStrippedState | read-write | current | Configures whether the IP stream is in null-stripped mode or not. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.8 | ColumnmpegiprcvBufferSize | read-write | current | Configures the input buffer size of the input IP stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.9 | ColumnmpegiprcvBufferDelay | read-only | current | Shows the delay of TS that results from the selected buffer size and received TS bitrate in ms. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.10 | ColumnmpegiprcvStreamIPPkts | read-only | current | Shows whether the IP packets are being received or not. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.11 | ColumnmpegiprcvTsPacketsPerIpPacket | read-only | current | Shows the number of Transport Stream packets per IP packet. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.12 | ColumnmpegiprcvEncapsulation | read-only | current | Shows the type of encapsulation (UDP/RTP) for the IP stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.13 | ColumnmpegiprcvSendIgmpReport | read-write | current | Commands to send an Unsolicited IGMP report to force a join operation for each IP stream to be received. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.14 | ColumnmpegiprcvIgmpFilterMode | read-write | current | Configures whether the IGMP filter list should be included or excluded. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.15 | ColumnmpegiprcvSsrcFilterState | read-write | current | Configures the enabled state of SSRC source filtering. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.16 | ColumnmpegiprcvSsrcFilterValue | read-write | current | Configures an SSRC value to use as a source filter. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.17 | ColumnmpegiprcvRtpOutOfOrderCount | read-only | current | Shows a count of out of order packets received in the stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.18 | ColumnmpegiprcvRtpDuplicateCount | read-only | current | Counter of the number of duplicate RTP packets received. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.19 | ColumnmpegiprcvRtpLostPacketCount | read-only | current | Counter of the number of missing packets according to the RTP sequence counter. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.20 | ColumnmpegiprcvRtpError | read-only | current | Set to 1 when uncorrected errors are detected when receiving RTP |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.21 | ColumnmpegiprcvResetCounters | read-write | current | Commands resetting of counters ( out of order, duplicate, etc. ) for the stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.22 | ColumnmpegiprcvFecState | read-write | current | Configures the enabled state of processing FEC data for the stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.23 | ColumnmpegiprcvFecRows | read-only | current | Shows the number of rows detected in the FEC data for the IP stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.24 | ColumnmpegiprcvFecColumns | read-only | current | Shows the number of columns detected in the FEC data for the IP stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.25 | ColumnmpegiprcvFecCorrectedCount | read-only | current | Shows the number of correctable FEC errors detected in the stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.26 | ColumnmpegiprcvFecUncorrectedCount | read-only | current | Shows the number of uncorrectable FEC errors detected in the stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.27 | ColumnmpegiprcvFecUncorrectedError | read-only | current | Shows the number of uncorrectable IP packets detected in the stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.28 | ColumnmpegiprcvFecCorrectedPerPeriod | read-only | current | Shows the number of correctable FEC errors per FEC period detected in the stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.29 | ColumnmpegiprcvPacketPresence | read-only | current | Shows the presence of packets when receiving an IP stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.30 | ColumnmpegiprcvBitrateExceededError | read-only | current | Shows the status of bitrate exceeded condition. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.31 | ColumnmpegiprcvFecErrorCond | read-only | current | FEC Reception Error Condition 1 = Out of Condition 2 = In Condition |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.32 | ColumnmpegiprcvRtpErrorCond | read-only | current | RTP Reception Error Condition 1 = Out of Condition 2 = In Condition |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.33 | ColumnmpegiprcvIpLossErrCond | read-only | current | IP Loss Error Condition 1 = Out of Condition 2 = In Condition |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.34 | ColumnmpegiprcvTsSyncLossCond | read-only | current | TS Sync Loss Error Condition 1 = Out of Condition 2 = In Condition |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.35 | ColumnmpegiprcvBitrateExceededErrorCond | read-only | current | Bitrate Exceeded Error Condition 1 = Out of Condition 2 = In Condition |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.36 | ColumnmpegiprcvBufferDelayTarget | read-write | current | The input buffer delay targeted value in ms (1-4000). |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.37 | ColumnmpegiprcvBufferMode | read-write | current | This configures the input buffer by Size (KB) or by Delay (ms). |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.38 | ColumnmpegiprcvWorstIat | read-only | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.39 | ColumnmpegiprcvWorstIatHistorical | read-only | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.40 | ColumnmpegiprcvCounterResetMode | read-write | current | Configure the reset mode to manual or auto. In manual mode, the user must manually reset the IP Metrics counters. In automatic mode, the counters automatically… |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.41 | ColumnmpegiprcvCounterResetInterval | read-write | current | Configure the auto reset interval. This value should be set to one minute increments. If it's not, it will be rounded to the nearest minute before using it. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.42 | ColumnmpegiprcvLastCounterReset | read-only | current | Shows the time of the last counter reset. The reset could be either a manual or an auto reset, depending on the mode that it used. |
| 1.3.6.1.4.1.9986.3.23.1.2.3.1.43 | ColumnmpegiprcvInternalSourceFilterState | read-write | current | Configures the type of source IP filtering. |
| 1.3.6.1.4.1.9986.3.23.1.2.4 | TablempegIpIgmpTable | not-accessible | current | MPEG/IP IGMP table. |
| 1.3.6.1.4.1.9986.3.23.1.2.4.1 | RowmpegIpIgmpEntry | not-accessible | current | MPEG/IP IGMP entry. |
| 1.3.6.1.4.1.9986.3.23.1.2.4.1.1 | ColumnmpegipigmpAddressType | not-accessible | current | The type of Internet address of IGMP IP address. At this time, only IPv4 is supported. |
| 1.3.6.1.4.1.9986.3.23.1.2.4.1.2 | ColumnmpegipigmpAddress | not-accessible | current | Configures the IGMP IP address. |
| 1.3.6.1.4.1.9986.3.23.1.2.4.1.3 | ColumnmpegipigmpRowStatus | read-create | current | The row status variable for the IGMP IP address. |
| 1.3.6.1.4.1.9986.3.23.1.2.5 | Tabledvbs2inTable | not-accessible | current | Configuration of DVB-S2 cards. |
| 1.3.6.1.4.1.9986.3.23.1.2.5.1 | Rowdvbs2inEntry | not-accessible | current | A configuration item of a DVB-S2 card. |
| 1.3.6.1.4.1.9986.3.23.1.2.5.1.1 | Columndvbs2inIndex | not-accessible | current | Identifies a DVB-S2 connector detected in the unit. |
| 1.3.6.1.4.1.9986.3.23.1.2.5.1.2 | Columndvbs2inConnMode | read-write | current | Configures the connection mode of the connector. |
| 1.3.6.1.4.1.9986.3.23.1.2.5.1.3 | Columndvbs2inConnLnbPower | read-write | current | Configures the LNB Power Voltage for the DVB-S2 connector. |
| 1.3.6.1.4.1.9986.3.23.1.2.5.1.4 | Columndvbs2inConn22KHzToneState | read-write | current | Configures the enabled state of the 22KHz tone for the connector. Application of this setting depends on LNB Power setting. |
| 1.3.6.1.4.1.9986.3.23.1.2.5.1.5 | Columndvbs2inConnLoOffset | read-write | current | Configures the Local Oscillator frequency, with precision 0.1MHz, for the DVB-S2 connector. |
| 1.3.6.1.4.1.9986.3.23.1.2.5.1.6 | Columndvbs2inConnSatFreq | read-write | current | Configures the Satellite frequency, with precision 0.1MHz, to tune to for the connector. |
| 1.3.6.1.4.1.9986.3.23.1.2.5.1.7 | Columndvbs2inConnSymbolRate | read-write | current | Configures the Symbol rate to tune to, for the connector. Reception may not be possible at rates less than 1000000 Sps and/or greater than 45000000 Sps. Valid … |
| 1.3.6.1.4.1.9986.3.23.1.2.5.1.8 | Columndvbs2inConnPlsCode | read-write | current | Configures the PL Scrambling Code for the DVB-S2 connector. |
| 1.3.6.1.4.1.9986.3.23.1.2.5.1.9 | Columndvbs2inConnWideSearchState | read-write | current | Configures the Wide Search option. This allow to extend the search range for various symbol rates. |
| 1.3.6.1.4.1.9986.3.23.1.2.5.1.10 | Columndvbs2inConnSymbolRateMode | read-write | current | Configures the Symbol Rate Mode |
| 1.3.6.1.4.1.9986.3.23.1.2.6 | Tabledvbs2instatusTable | not-accessible | current | DVB-S2 status reporting. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1 | Rowdvbs2instatusEntry | not-accessible | current | A DVB-S2 status item. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.1 | Columndvbs2instatusIndex | not-accessible | current | Identifies a DVB-S2 status item. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.2 | Columndvbs2instatusActivePort | read-only | current | Shows whether the connector is active or not. Only one port is active at any time. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.3 | Columndvbs2instatusTuningFreq | read-only | current | Shows the tuning frequency, which is based on the satellite frequency and LO frequency configuration for the connector. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.4 | Columndvbs2instatusConnModulation | read-only | current | Shows the modulation detected for the locked signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.5 | Columndvbs2instatusConnFEC | read-only | current | Shows the FEC code rate for the locked signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.6 | Columndvbs2instatusConnLevel | read-only | current | Shows the signal level of the locked signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.7 | Columndvbs2instatusConnPilots | read-only | current | Shows whether or not pilots are detected in a locked signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.8 | Columndvbs2instatusConnSpectrum | read-only | current | Shows whether the spectrum is inverted or not in the detected signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.9 | Columndvbs2instatusConnLockedFreq | read-only | current | Shows the frequency at which the signal has been locked on to. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.10 | Columndvbs2instatusConnTSPresence | read-only | current | Shows whether a Tranport Stream presence is detected or not. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.11 | Columndvbs2instatusConnSigQualMetric | read-only | current | Shows the signal quality metric (Eb/No in a locked DVB-S signal or C/N of a locked DVB-S2 signal). |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.12 | Columndvbs2instatusConnLinkMargin | read-only | current | Shows the difference between the measured signal quality of the locked signal and the theoretical minimum value presented in the relevant standard. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.13 | Columndvbs2instatusConnErrorRate | read-only | current | Shows BER for locked DVB-S signal or PER for locked DVB-S2 signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.14 | Columndvbs2instatusConnRcvLock | read-only | current | Shows whether a lock has been acquired on the input signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.15 | Columndvbs2instatusLnbPowerAnotherSrc | read-only | current | Shows the LNB Power Protection status. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.16 | Columndvbs2instatusLnbPowerHighCurrent | read-only | current | Shows the LNB Power Protection status. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.17 | Columndvbs2instatusLnbPowerOverVoltage | read-only | current | Shows the LNB Power Protection status. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.18 | Columndvbs2instatusMultistreamDetected | read-only | current | Shows whether the input stream is a multistream or not. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.19 | Columndvbs2instatusVCMDetected | read-only | current | Shows whether the locked input signal stream type is CCM or VCM. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.20 | Columndvbs2instatusLossofReceiverLockCond | read-only | current | Loss of Receiver Lock. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.21 | Columndvbs2instatusLnbPowerErrorCond | read-only | current | LNB Power Error. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.22 | Columndvbs2instatusUnlicensedModulationCond | read-only | current | Unlicensed Modulation |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.23 | Columndvbs2instatusUnlicensedMultiStreamCond | read-only | current | Unlicensed Multistream |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.24 | Columndvbs2instatusTsSyncLossCond | read-only | current | TS Sync Loss |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.25 | Columndvbs2instatusConnFrameLength | read-only | current | Shows whether the locked input DVB-S2 stream frame length is Normal or Short. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.26 | Columndvbs2instatusConnStandardType | read-only | current | Shows the detected modulation standard for the locked signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.6.1.27 | Columndvbs2instatusConnSymbolRate | read-only | current | Shows the auto detected symbol rate, expressed in Sps. |
| 1.3.6.1.4.1.9986.3.23.1.2.7 | Tabledvbs2advfeatureTable | not-accessible | current | Configuration items for the DVB-S2 advanced features. This configuration is applied only when the unit is licensed for DVB-S2 advanced license. |
| 1.3.6.1.4.1.9986.3.23.1.2.7.1 | Rowdvbs2advfeatureEntry | not-accessible | current | Configuration for an advanced feature for the DVB-S2 card. |
| 1.3.6.1.4.1.9986.3.23.1.2.7.1.1 | Columndvbs2advfeatureIndex | not-accessible | current | Identifies an instance of DVB-S2 advanced feature configuration. |
| 1.3.6.1.4.1.9986.3.23.1.2.7.1.2 | Columndvbs2advfeatureMultiStreamState | read-write | current | Configures the enabled state of Multistream mode. This setting is applied only when the unit is licensed for the DVB-S2 advanced license. |
| 1.3.6.1.4.1.9986.3.23.1.2.7.1.3 | Columndvbs2advfeatureISI | read-write | current | Configures the ISI number of the stream to be tuned to, in multistream mode. This setting is applied only when the multistream mode is enabled and the unit is … |
| 1.3.6.1.4.1.9986.3.23.1.2.7.1.4 | Columndvbs2advfeatureMultistreamMismatchCond | read-only | current | Multistream Mode Input Mismatch. |
| 1.3.6.1.4.1.9986.3.23.1.2.7.1.5 | Columndvbs2advfeatureISINotFoundCond | read-only | current | ISI Not Found. |
| 1.3.6.1.4.1.9986.3.23.1.2.8 | Tabledvbs2isiTable | not-accessible | current | Lists ISIs detected in the input signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.8.1 | Rowdvbs2isiEntry | not-accessible | current | Each entry shows an ISI detected in the transport stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.8.1.1 | Columndvbs2isiIndex | not-accessible | current | Identifies a DVB-S2 ISI instance. |
| 1.3.6.1.4.1.9986.3.23.1.2.8.1.2 | Columndvbs2isiIsiIndex | not-accessible | current | Identifies an ISI detected in the signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.8.1.3 | Columndvbs2isiNumber | read-only | current | Shows an ISI detected in the multistream signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.9 | TableasiinTable | not-accessible | current | ASI input table. |
| 1.3.6.1.4.1.9986.3.23.1.2.9.1 | RowasiinEntry | not-accessible | current | ASI input entry. |
| 1.3.6.1.4.1.9986.3.23.1.2.9.1.1 | ColumnasiinIndex | not-accessible | current | Identifies an ASI input source. |
| 1.3.6.1.4.1.9986.3.23.1.2.9.1.2 | ColumnasiinTsSyncLossCond | read-only | obsolete | This variable is obsolete. Refer to asiioTsSyncLossCond. |
| 1.3.6.1.4.1.9986.3.23.1.2.9.1.3 | ColumnasiinNullStrippedState | read-write | current | Configures whether the ASI stream is in null-stripped mode or not. |
| 1.3.6.1.4.1.9986.3.23.1.2.10 | TablevsbInTable | not-accessible | current | VSB input source table. |
| 1.3.6.1.4.1.9986.3.23.1.2.10.1 | RowvsbInEntry | not-accessible | current | VSB input source entry. |
| 1.3.6.1.4.1.9986.3.23.1.2.10.1.1 | ColumnvsbInIndex | not-accessible | current | Identifies a VSB input source. |
| 1.3.6.1.4.1.9986.3.23.1.2.10.1.2 | ColumnvsbinModulation | read-write | current | Configures the modulation mode (8VSB, 64-QAMB, or 256-QAMB) of the connector. |
| 1.3.6.1.4.1.9986.3.23.1.2.10.1.3 | ColumnvsbinChannelPlan | read-write | current | Configures the channel plan among US Broadcast, FCC Cable, HRC Cable and IRC Cable. |
| 1.3.6.1.4.1.9986.3.23.1.2.10.1.4 | ColumnvsbinRfChannel | read-write | current | Configures RF channel number range. The range for US Broadcast shall be 2-69. The range for FCC Cable, HRC Cable and IRC Cable shall be 2-158. |
| 1.3.6.1.4.1.9986.3.23.1.2.10.1.5 | ColumnvsbinRfLock | read-only | current | Shows whether a lock has been acquired on the input signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.10.1.6 | ColumnvsbinRfLevel | read-only | current | Shows the measurement of the channel power level of the received signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.10.1.7 | ColumnvsbinMer | read-only | current | Shows the measurement of the MER of the received signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.10.1.8 | ColumnvsbinCorrectableFecErrors | read-only | current | Shows the number of the correctable FEC errors that have occured. |
| 1.3.6.1.4.1.9986.3.23.1.2.10.1.9 | ColumnvsbinUncorrectableFecErrors | read-only | current | Shows the number of uncorrectable FEC errors that have occured. |
| 1.3.6.1.4.1.9986.3.23.1.2.10.1.10 | ColumnvsbinFecErrorsReset | read-write | current | Commands resettings of the counters (uncorrectable FEC and correctable FEC) of the stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.10.1.11 | ColumnvsbinRfLockLostCond | read-only | current | RF Lock Lost. |
| 1.3.6.1.4.1.9986.3.23.1.2.10.1.12 | ColumnvsbinTsSyncLossCond | read-only | current | TS Sync Loss. |
| 1.3.6.1.4.1.9986.3.23.1.2.10.1.13 | ColumnvsbinLowLevelThreshold | read-write | current | Configures a low level threshold for the VSB receiver. |
| 1.3.6.1.4.1.9986.3.23.1.2.10.1.14 | ColumnvsbinLowLevelCond | read-only | current | Low Level. |
| 1.3.6.1.4.1.9986.3.23.1.2.10.1.15 | ColumnvsbinLowMerThreshold | read-write | current | Configures a low MER threshold for a VSB receiver. |
| 1.3.6.1.4.1.9986.3.23.1.2.10.1.16 | ColumnvsbinLowMerCond | read-only | current | Low MER. |
| 1.3.6.1.4.1.9986.3.23.1.2.10.1.17 | ColumnvsbinSelectedFrequency | read-only | current | Shows the selected frequency. |
| 1.3.6.1.4.1.9986.3.23.1.2.11 | TableturbopskinTable | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.11.1 | RowturbopskinEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.11.1.1 | ColumnturbopskinIndex | not-accessible | current | Identifies a TurboPSK receiver detected in the unit. |
| 1.3.6.1.4.1.9986.3.23.1.2.11.1.2 | ColumnturbopskinMode | read-write | current | Configures the mode (DVB-S or TurboPSK). |
| 1.3.6.1.4.1.9986.3.23.1.2.11.1.3 | ColumnturbopskinModulationMode | read-write | current | Configures the modulation mode. |
| 1.3.6.1.4.1.9986.3.23.1.2.11.1.4 | ColumnturbopskinLoOffset | read-write | current | Configures the Local Oscillator frequency expressed in kHz, with 100 kHz precision. |
| 1.3.6.1.4.1.9986.3.23.1.2.11.1.5 | ColumnturbopskinSatelliteFreq | read-write | current | Configures the Satellite frequency expressed in kHz, with 100 kHz precision, to tune to. |
| 1.3.6.1.4.1.9986.3.23.1.2.11.1.6 | ColumnturbopskinSymbolRate | read-write | current | Configures the Symbol rate expressed in Sps to tune to. Reception may not be possible at rates less than 1000000 Sps. |
| 1.3.6.1.4.1.9986.3.23.1.2.11.1.7 | ColumnturbopskinTuningFreq | read-only | current | Shows the tuning frequency in Hz, which is based on the satellite frequency and LO frequency configuration. |
| 1.3.6.1.4.1.9986.3.23.1.2.11.1.8 | ColumnturbopskinRcvLock | read-only | current | Shows whether a lock has been acquired on the input signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.11.1.9 | ColumnturbopskinLevel | read-only | current | Shows the signal level of the locked signal expressed in dBm. |
| 1.3.6.1.4.1.9986.3.23.1.2.11.1.10 | ColumnturbopskinSpectrum | read-only | current | Shows whether the spectrum is inverted or not in the detected signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.11.1.11 | ColumnturbopskinLockedFreq | read-only | current | Shows the frequency expressed in Hz at which the signal has been locked on to. |
| 1.3.6.1.4.1.9986.3.23.1.2.11.1.12 | ColumnturbopskinSnr | read-only | current | Shows the signal to noise ratio expressed in 0.1dB steps. |
| 1.3.6.1.4.1.9986.3.23.1.2.11.1.13 | ColumnturbopskinCarrierLockLossCond | read-only | current | Carrier lock loss. |
| 1.3.6.1.4.1.9986.3.23.1.2.11.1.14 | ColumnturbopskinTsSyncLossCond | read-only | current | TS Sync Loss |
| 1.3.6.1.4.1.9986.3.23.1.2.12 | Tabledvbt2isdbtinTable | not-accessible | current | Common configuration items for DVB-T/DVB-T2/DVB-C/DVB-C2/ISDB-T input. |
| 1.3.6.1.4.1.9986.3.23.1.2.12.1 | Rowdvbt2isdbtinEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.12.1.1 | Columndvbt2isdbtinIndex | not-accessible | current | Identifies the DVB-T2 input source. |
| 1.3.6.1.4.1.9986.3.23.1.2.12.1.2 | Columndvbt2isdbtinMode | read-write | current | Configures the receiver modulation mode. |
| 1.3.6.1.4.1.9986.3.23.1.2.12.1.3 | Columndvbt2isdbtinTuningFreq | read-write | current | Configures the tuning frequency. |
| 1.3.6.1.4.1.9986.3.23.1.2.12.1.4 | Columndvbt2isdbtinTunerBandwidth | read-write | current | Configures the bandwidth to use for tuning. |
| 1.3.6.1.4.1.9986.3.23.1.2.12.1.5 | Columndvbt2isdbtinLowLevelThreshold | read-write | current | Configures the signal low level threshold. |
| 1.3.6.1.4.1.9986.3.23.1.2.12.1.6 | Columndvbt2isdbtinLowMerThreshold | read-write | current | Configures the low modulation error ratio threshold for receiver. |
| 1.3.6.1.4.1.9986.3.23.1.2.12.1.7 | Columndvbt2isdbtinDvbTChannelPlan | read-write | current | Selects the channel plan for DVB-T modulation mode. A channel plan defines a list of channels, where each channel is a specific combination of frequency and ba… |
| 1.3.6.1.4.1.9986.3.23.1.2.12.1.8 | Columndvbt2isdbtinDvbT2ChannelPlan | read-write | current | Selects the channel plan for DVB-T2 modulation mode. A channel plan defines a list of channels, where each channel is a specific combination of frequency and b… |
| 1.3.6.1.4.1.9986.3.23.1.2.12.1.9 | Columndvbt2isdbtinDvbT2C2PlpId | read-write | current | Configures the PLP ID for DVB-T2 or DVB-C2 modulation mode. |
| 1.3.6.1.4.1.9986.3.23.1.2.12.1.10 | Columndvbt2isdbtinDvbT2Profile | read-write | current | Configures the profile for DVB-T2 modulation mode. |
| 1.3.6.1.4.1.9986.3.23.1.2.12.1.11 | Columndvbt2isdbtinDvbCChannelPlan | read-write | current | Selects the channel plan for DVB-C modulation mode. A channel plan defines a list of channels, where each channel is a specific combination of frequency and ba… |
| 1.3.6.1.4.1.9986.3.23.1.2.12.1.12 | Columndvbt2isdbtinDvbC2ChannelPlan | read-write | current | Selects the channel plan for DVB-C2 modulation mode. A channel plan defines a list of channels, where each channel is a specific combination of frequency and b… |
| 1.3.6.1.4.1.9986.3.23.1.2.12.1.13 | Columndvbt2isdbtinIsdbTChannelPlan | read-write | current | Selects the channel plan for ISDBT modulation mode. A channel plan defines a list of channels, where each channel is a specific combination of frequency and ba… |
| 1.3.6.1.4.1.9986.3.23.1.2.13 | Tabledvbt2isdbtinstatusTable | not-accessible | current | Common status items for DVB-T/DVB-T2/DVB-C/DVB-C2/ISDB-T input. |
| 1.3.6.1.4.1.9986.3.23.1.2.13.1 | Rowdvbt2isdbtinstatusEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.13.1.1 | Columndvbt2isdbtinstatusRcvLock | read-only | current | Shows whether a lock has been acquired on the input signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.13.1.2 | Columndvbt2isdbtinstatusChannelPowerLevel | read-only | current | Shows the channel power level of the received signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.13.1.3 | Columndvbt2isdbtinstatusMer | read-only | current | Shows the modulation error ratio of received signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.13.1.4 | Columndvbt2isdbtinstatusTuningFreq | read-only | current | Shows the actual tuning frequency used by receiver compared to user set value. |
| 1.3.6.1.4.1.9986.3.23.1.2.13.1.5 | Columndvbt2isdbtinstatusSpectralInversion | read-only | current | Shows the channel spectrum sense(normal or inverted). |
| 1.3.6.1.4.1.9986.3.23.1.2.13.1.6 | Columndvbt2isdbtinstatusRfLockLossCond | read-only | current | Shows the loss of RF lock condition. |
| 1.3.6.1.4.1.9986.3.23.1.2.13.1.7 | Columndvbt2isdbtinstatusTsSyncLossCond | read-only | current | Shows the TS sync loss condition. |
| 1.3.6.1.4.1.9986.3.23.1.2.13.1.8 | Columndvbt2isdbtinstatusLowLevelCond | read-only | current | Shows the low signal level condition. |
| 1.3.6.1.4.1.9986.3.23.1.2.13.1.9 | Columndvbt2isdbtinstatusLowMerCond | read-only | current | Shows the low modulation error ratio condition. |
| 1.3.6.1.4.1.9986.3.23.1.2.13.1.10 | Columndvbt2isdbtinstatusPlpNotFoundCond | read-only | current | Shows the selected PLP not found condition. |
| 1.3.6.1.4.1.9986.3.23.1.2.13.1.11 | Columndvbt2isdbtinstatusChannel | read-only | current | |
| 1.3.6.1.4.1.9986.3.23.1.2.14 | TabledvbtinstatusTable | not-accessible | current | Status items for DVB-T input. |
| 1.3.6.1.4.1.9986.3.23.1.2.14.1 | RowdvbtinstatusEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.14.1.1 | ColumndvbtinstatusConstellation | read-only | current | Shows the constellation type. |
| 1.3.6.1.4.1.9986.3.23.1.2.14.1.2 | ColumndvbtinstatusCodeRate | read-only | current | Shows the code rate associated with active input channel. |
| 1.3.6.1.4.1.9986.3.23.1.2.14.1.3 | ColumndvbtinstatusGuardInterval | read-only | current | Shows the guard interval of signal associated with active input channel. |
| 1.3.6.1.4.1.9986.3.23.1.2.14.1.4 | ColumndvbtinstatusTransmission | read-only | current | Shows the transmission mode of signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.14.1.5 | ColumndvbtinstatusHierarchy | read-only | current | Shows whether the transmission is hierarchical and if so what the alpha value is. |
| 1.3.6.1.4.1.9986.3.23.1.2.14.1.6 | ColumndvbtinstatusProfile | read-only | current | Shows the profile (high or low priority) |
| 1.3.6.1.4.1.9986.3.23.1.2.14.1.7 | ColumndvbtinstatusPreVitBer | read-only | current | Shows the pre-viterbi bit error rate. |
| 1.3.6.1.4.1.9986.3.23.1.2.14.1.8 | ColumndvbtinstatusPreRsBer | read-only | current | Shows the pre-RS bit error rate. |
| 1.3.6.1.4.1.9986.3.23.1.2.15 | Tabledvbt2instatusTable | not-accessible | current | Status items for DVB-T2 input. |
| 1.3.6.1.4.1.9986.3.23.1.2.15.1 | Rowdvbt2instatusEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.15.1.1 | Columndvbt2instatusP1SisoMiso | read-only | current | Shows the P1 signalling parameter SISO/MISO. |
| 1.3.6.1.4.1.9986.3.23.1.2.15.1.2 | Columndvbt2instatusP1FftSize | read-only | current | Shows the P1 signalling parameter FFT size. |
| 1.3.6.1.4.1.9986.3.23.1.2.15.1.3 | Columndvbt2instatusL1PreGuardInterval | read-only | current | Shows the L1 pre-signalling guard interval. |
| 1.3.6.1.4.1.9986.3.23.1.2.15.1.4 | Columndvbt2instatusL1PrePapr | read-only | current | Shows the L1 pre-signalling PAPR. |
| 1.3.6.1.4.1.9986.3.23.1.2.15.1.5 | Columndvbt2instatusL1PreL1Mod | read-only | current | Shows the L1 pre-signalling modulation. |
| 1.3.6.1.4.1.9986.3.23.1.2.15.1.6 | Columndvbt2instatusL1PrePilotPattern | read-only | current | Shows the L1 pre-signalling pilot pattern. |
| 1.3.6.1.4.1.9986.3.23.1.2.15.1.7 | Columndvbt2instatusL1PreOfdmSymbolPerFrame | read-only | current | Shows the L1 pre-signalling OFDM symbol per T2 frame. |
| 1.3.6.1.4.1.9986.3.23.1.2.15.1.8 | Columndvbt2instatusPlpCount | read-only | current | Shows the number of PLPs present in active input channel indicated by L1 post-signalling field. |
| 1.3.6.1.4.1.9986.3.23.1.2.15.1.9 | Columndvbt2instatusPreLdpcBer | read-only | current | Shows the pre-LDPC bit error rate. |
| 1.3.6.1.4.1.9986.3.23.1.2.15.1.10 | Columndvbt2instatusPreBchBer | read-only | current | Shows the Pre-BCH bit error rate. |
| 1.3.6.1.4.1.9986.3.23.1.2.16 | Tabledvbt2plpstatusTable | not-accessible | current | Status items for DVB-T2 PLP. |
| 1.3.6.1.4.1.9986.3.23.1.2.16.1 | Rowdvbt2plpstatusEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.16.1.1 | Columndvbt2plpstatusId | read-only | current | Shows the PLP ID for DVB-T2 modulation, formatted as 1000 + PLP ID. E.g. PLP ID 123 is formatted as 1123. |
| 1.3.6.1.4.1.9986.3.23.1.2.17 | Tabledvbt2actplpstatusTable | not-accessible | current | Status items for DVB-T2 active PLP. |
| 1.3.6.1.4.1.9986.3.23.1.2.17.1 | Rowdvbt2actplpstatusEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.17.1.1 | Columndvbt2actplpstatusId | read-only | current | Shows the active PLP ID for DVB-T2 modulation mode. |
| 1.3.6.1.4.1.9986.3.23.1.2.17.1.2 | Columndvbt2actplpstatusL1PostMod | read-only | current | Shows the active PLP modulation for DVB-T2. |
| 1.3.6.1.4.1.9986.3.23.1.2.17.1.3 | Columndvbt2actplpstatusL1PostCodeRate | read-only | current | Shows the active PLP code rate. |
| 1.3.6.1.4.1.9986.3.23.1.2.17.1.4 | Columndvbt2actplpstatusL1PostFecType | read-only | current | Shows the FEC type used by associated active PLP. |
| 1.3.6.1.4.1.9986.3.23.1.2.17.1.5 | Columndvbt2actplpstatusL1PostRotation | read-only | current | Shows whether the constellation rotation is in use or not by associated active PLP. |
| 1.3.6.1.4.1.9986.3.23.1.2.18 | TabledvbcinstatusTable | not-accessible | current | Status items for DVB-C input. |
| 1.3.6.1.4.1.9986.3.23.1.2.18.1 | RowdvbcinstatusEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.18.1.1 | ColumndvbcinstatusConstellation | read-only | current | Shows the constellatin for DVB-C modulation. |
| 1.3.6.1.4.1.9986.3.23.1.2.18.1.2 | ColumndvbcinstatusSymbolRate | read-only | current | Shows the symbol rate for DVB-C modulation in Sps. |
| 1.3.6.1.4.1.9986.3.23.1.2.18.1.3 | ColumndvbcinstatusPacketErrorRate | read-only | current | Shows the packet error rate for DVB-C modulation. |
| 1.3.6.1.4.1.9986.3.23.1.2.18.1.4 | ColumndvbcinstatusPreRsBer | read-only | current | Shows the pre-RS BER for DVB-C modulation mode. |
| 1.3.6.1.4.1.9986.3.23.1.2.19 | Tabledvbc2instatusTable | not-accessible | current | Status items for DVB-C2 input. |
| 1.3.6.1.4.1.9986.3.23.1.2.19.1 | Rowdvbc2instatusEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.19.1.1 | Columndvbc2instatusL1GuardInterval | read-only | current | Shows the L1 guard interval for DVB-C2 modulation. |
| 1.3.6.1.4.1.9986.3.23.1.2.19.1.2 | Columndvbc2instatusL1DataSliceCount | read-only | current | Shows the number of data slices carried within the current C2 frame. |
| 1.3.6.1.4.1.9986.3.23.1.2.19.1.3 | Columndvbc2instatusL1NotchBandsCount | read-only | current | Shows the number of notch band within the current C2 frame. |
| 1.3.6.1.4.1.9986.3.23.1.2.19.1.4 | Columndvbc2instatusL1PacketErrorRate | read-only | current | Shows the packet error rate. |
| 1.3.6.1.4.1.9986.3.23.1.2.19.1.5 | Columndvbc2instatusL1PreLdpcBer | read-only | current | Shows the pre-LDPC bit error rate. |
| 1.3.6.1.4.1.9986.3.23.1.2.19.1.6 | Columndvbc2instatusL1PreBchBer | read-only | current | Shows the pre-BCH bit error rate. |
| 1.3.6.1.4.1.9986.3.23.1.2.20 | Tabledvbc2actdslicestatusTable | not-accessible | current | Status items for active data slice. |
| 1.3.6.1.4.1.9986.3.23.1.2.20.1 | Rowdvbc2actdslicestatusEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.20.1.1 | Columndvbc2actdslicestatusId | read-only | current | Shows the data slice ID for DVB-C2 modulation. |
| 1.3.6.1.4.1.9986.3.23.1.2.20.1.2 | Columndvbc2actdslicestatusType | read-only | current | Shows the type of associated data slice. |
| 1.3.6.1.4.1.9986.3.23.1.2.20.1.3 | Columndvbc2actdslicestatusFecHeaderType | read-only | current | Shows the type of FEC frame header within the associated data slice. |
| 1.3.6.1.4.1.9986.3.23.1.2.20.1.4 | Columndvbc2actdslicestatusConfiguration | read-only | current | Shows whether the configuration of associated data slice is variable or fixed. |
| 1.3.6.1.4.1.9986.3.23.1.2.20.1.5 | Columndvbc2actdslicestatusPlpCount | read-only | current | Shows the number of PLPs carried within the associated data slice. |
| 1.3.6.1.4.1.9986.3.23.1.2.21 | Tabledvbc2plpstatusTable | not-accessible | current | Status items for DVB-C2 PLP. |
| 1.3.6.1.4.1.9986.3.23.1.2.21.1 | Rowdvbc2plpstatusEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.21.1.1 | Columndvbc2plpstatusId | read-only | current | Shows the PLP ID for DVB-C2 modulation, formatted as 1000 + PLP ID. E.g. PLP ID 123 is formatted as 1123. |
| 1.3.6.1.4.1.9986.3.23.1.2.22 | Tabledvbc2actplpstatusTable | not-accessible | current | Status items for DVB-C2 active PLP. |
| 1.3.6.1.4.1.9986.3.23.1.2.22.1 | Rowdvbc2actplpstatusEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.22.1.1 | Columndvbc2actplpstatusId | read-only | current | Shows the active (selected) PLP ID with in C2 system. |
| 1.3.6.1.4.1.9986.3.23.1.2.22.1.2 | Columndvbc2actplpstatusFecType | read-only | current | Shows the FEC type used by associated PLP in C2 system. |
| 1.3.6.1.4.1.9986.3.23.1.2.22.1.3 | Columndvbc2actplpstatusMod | read-only | current | Shows the modulation used by associated PLP. |
| 1.3.6.1.4.1.9986.3.23.1.2.22.1.4 | Columndvbc2actplpstatusCodeRate | read-only | current | Shows the code rate used by associated PLP. |
| 1.3.6.1.4.1.9986.3.23.1.2.23 | TableisdbtinstatusTable | not-accessible | current | Status items for ISDB-T input. |
| 1.3.6.1.4.1.9986.3.23.1.2.23.1 | RowisdbtinstatusEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.23.1.1 | ColumnisdbtinstatusSystemId | read-only | current | Shows the system ID for ISDB-T modulation. |
| 1.3.6.1.4.1.9986.3.23.1.2.23.1.2 | ColumnisdbtinstatusSystemMode | read-only | current | Shows the system mode for ISDB-T modulation. |
| 1.3.6.1.4.1.9986.3.23.1.2.23.1.3 | ColumnisdbtinstatusGuardInterval | read-only | current | Shows the guard interval associated with ISDB-T. |
| 1.3.6.1.4.1.9986.3.23.1.2.24 | TableisdbtlayerstatusTable | not-accessible | current | Status items for ISDB-T hierarchial layer. |
| 1.3.6.1.4.1.9986.3.23.1.2.24.1 | RowisdbtlayerstatusEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.24.1.1 | ColumnisdbtlayerstatusIndex | not-accessible | current | Specifies the hierarchial layer in ISDB-T modulation. |
| 1.3.6.1.4.1.9986.3.23.1.2.24.1.2 | ColumnisdbtlayerstatusModScheme | read-only | current | Shows the TMCC modulation scheme associated with hierarchial layer in ISDB-T. |
| 1.3.6.1.4.1.9986.3.23.1.2.24.1.3 | ColumnisdbtlayerstatusCodeRate | read-only | current | Shows the TMCC coding rate for ISDBT hierarchial layer. |
| 1.3.6.1.4.1.9986.3.23.1.2.24.1.4 | ColumnisdbtlayerstatusInterleaveLength | read-only | current | Shows the TMCC interleave length for ISDB-T hierarchial layer. |
| 1.3.6.1.4.1.9986.3.23.1.2.24.1.5 | ColumnisdbtlayerstatusSegmentCount | read-only | current | Shows the TMCC number of segments for ISDB-T hierarchial layer. |
| 1.3.6.1.4.1.9986.3.23.1.2.24.1.6 | ColumnisdbtlayerstatusPacketErrorRate | read-only | current | Shows the packet error rate for ISDB-T hierarchial layer. |
| 1.3.6.1.4.1.9986.3.23.1.2.24.1.7 | ColumnisdbtlayerstatusPreRsBer | read-only | current | Shows the pre-RS BER for ISDB-T hierarchial layer. |
| 1.3.6.1.4.1.9986.3.23.1.2.25 | TablempegipinternalfilterTable | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.25.1 | RowmpegipinternalfilterEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.25.1.1 | ColumnmpegipinternalfilterAddressType | not-accessible | current | The type of internal source IP filter. At this time, only IPv4 is supported. |
| 1.3.6.1.4.1.9986.3.23.1.2.25.1.2 | ColumnmpegipinternalfilterIpAddress | read-only | current | Configures the internal source filter IP address. |
| 1.3.6.1.4.1.9986.3.23.1.2.25.1.3 | ColumnmpegipinternalfilterRowStatus | read-create | current | The row status variable for the internal source filter. |
| 1.3.6.1.4.1.9986.3.23.1.2.26 | TableasiioTable | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.26.1 | RowasiioEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.26.1.1 | ColumnasiioIndex | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.2.26.1.2 | ColumnasiioDirection | read-write | current | Configures the ASI I/O direction. |
| 1.3.6.1.4.1.9986.3.23.1.2.26.1.3 | ColumnasiioNullStrippedState | read-write | current | Configures the ASI I/O input null stripped state. |
| 1.3.6.1.4.1.9986.3.23.1.2.26.1.4 | ColumnasiioCapability | read-only | current | Shows the ASI port capability. |
| 1.3.6.1.4.1.9986.3.23.1.2.26.1.5 | ColumnasiioTsSyncLossCond | read-only | current | Shows the TS sync loss condition. |
| 1.3.6.1.4.1.9986.3.23.1.2.27 | Tabledvbs2xinTable | not-accessible | current | DVB-S2X input stream configuration table. |
| 1.3.6.1.4.1.9986.3.23.1.2.27.1 | Rowdvbs2xinEntry | not-accessible | current | DVB-S2X input stream configuration entry. |
| 1.3.6.1.4.1.9986.3.23.1.2.27.1.1 | Columndvbs2xinIndex | not-accessible | current | Identifies a DVB-S2X input stream detected in the unit. |
| 1.3.6.1.4.1.9986.3.23.1.2.27.1.2 | Columndvbs2xinConnPhysicalConnector | read-write | current | Configures the selected RF connector for the input stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.27.1.3 | Columndvbs2xinConnSatFreq | read-write | current | Configures the Satellite frequency to tune to for the input stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.27.1.4 | Columndvbs2xinConnLoOffset | read-write | current | Configures the Local Oscillator frequency, with precision 0.1MHz, for the input stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.27.1.5 | Columndvbs2xinConnPlScramblingCode | read-write | current | Configures the PL Scrambling Code for the input stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.27.1.6 | Columndvbs2xinConnSymbolRateMode | read-write | current | Configures the Symbol Rate Mode. |
| 1.3.6.1.4.1.9986.3.23.1.2.27.1.7 | Columndvbs2xinConnSymbolRate | read-write | current | Configures the Symbol rate to tune to, for the connector. Reception may not be possible at rates less than 1000000 Sps and/or greater than 45000000 Sps. Valid … |
| 1.3.6.1.4.1.9986.3.23.1.2.28 | Tabledvbs2xinstatusTable | not-accessible | current | DVB-S2X input stream status table. |
| 1.3.6.1.4.1.9986.3.23.1.2.28.1 | Rowdvbs2xinstatusEntry | not-accessible | current | DVB-S2X input stream status entry. |
| 1.3.6.1.4.1.9986.3.23.1.2.28.1.1 | Columndvbs2xinstatusIndex | not-accessible | current | Identifies a DVB-S2X input stream detected in the unit. |
| 1.3.6.1.4.1.9986.3.23.1.2.28.1.2 | Columndvbs2xinstatusConnTuningFreq | read-only | current | Shows the tuning frequency, which is based on the satellite frequency and LO offset frequency configuration for the input stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.28.1.3 | Columndvbs2xinstatusConnRcvLock | read-only | current | Shows whether a lock has been acquired on the input stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.28.1.4 | Columndvbs2xinstatusConnStandardType | read-only | current | Shows the detected modulation standard for the locked signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.28.1.5 | Columndvbs2xinstatusConnModulation | read-only | current | Shows the modulation detected for the locked signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.28.1.6 | Columndvbs2xinstatusConnFEC | read-only | current | Shows the code rate associated with the active input stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.28.1.7 | Columndvbs2xinstatusConnLevel | read-only | current | Shows the signal level of the locked signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.28.1.8 | Columndvbs2xinstatusConnPilots | read-only | current | Shows whether or not pilots are detected in a locked signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.28.1.9 | Columndvbs2xinstatusConnFrameLength | read-only | current | Shows whether the locked input stream frame length is Normal or Short. |
| 1.3.6.1.4.1.9986.3.23.1.2.28.1.10 | Columndvbs2xinstatusConnSpectrum | read-only | current | Shows whether the spectrum is inverted or not in the detected signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.28.1.11 | Columndvbs2xinstatusConnLockedFreq | read-only | current | Shows the locked on frequency frequency for the signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.28.1.12 | Columndvbs2xinstatusConnSymbolRate | read-only | current | Shows the detected and locked symbol rate. |
| 1.3.6.1.4.1.9986.3.23.1.2.28.1.13 | Columndvbs2xinstatusConnSigQualMetric | read-only | current | Shows the signal quality metric (Eb/No of a locked DVB-S signal or C/N of a locked DVB-S2 or DVB-S2X signal). |
| 1.3.6.1.4.1.9986.3.23.1.2.28.1.14 | Columndvbs2xinstatusConnLinkMargin | read-only | current | Shows the difference between the measured signal quality of the locked signal and the theoretical minimum value presented in the relevant standard. |
| 1.3.6.1.4.1.9986.3.23.1.2.28.1.15 | Columndvbs2xinstatusConnErrorRate | read-only | current | Shows BER for a locked DVB-S signal or PER for a locked DVB-S2 or DVB-S2X signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.28.1.16 | Columndvbs2xinstatusMultistreamDetected | read-only | current | Shows whether the input stream is a multistream or not. |
| 1.3.6.1.4.1.9986.3.23.1.2.28.1.17 | Columndvbs2xinstatusLossofReceiverLockCond | read-only | current | Indicates that the input stream has lost lock. |
| 1.3.6.1.4.1.9986.3.23.1.2.28.1.18 | Columndvbs2xinstatusTsSyncLossCond | read-only | current | Indicates that the input transport stream has lost sync. |
| 1.3.6.1.4.1.9986.3.23.1.2.28.1.19 | Columndvbs2xinstatusUnlicensedModulationCond | read-only | current | Indicates that the input stream has an unlicensed modulation. |
| 1.3.6.1.4.1.9986.3.23.1.2.28.1.20 | Columndvbs2xinstatusUnlicensedMultiStreamCond | read-only | current | Indicates that the input stream is multistream and that feature is unlicensed. |
| 1.3.6.1.4.1.9986.3.23.1.2.29 | Tabledvbs2xadvfeatureTable | not-accessible | current | Configuration items for the DVB-S2X advanced features. This configuration is applied only when the unit is licensed for DVB-S2X advanced license. |
| 1.3.6.1.4.1.9986.3.23.1.2.29.1 | Rowdvbs2xadvfeatureEntry | not-accessible | current | Configuration for an advanced feature for the DVB-S2X card. |
| 1.3.6.1.4.1.9986.3.23.1.2.29.1.1 | Columndvbs2xadvfeatureISI | read-write | current | Configures the ISI number of the stream to be tuned to, in multistream mode. This setting is applied only when the multistream mode is enabled and the unit is … |
| 1.3.6.1.4.1.9986.3.23.1.2.29.1.2 | Columndvbs2xadvfeatureISINotFoundCond | read-only | current | Indicates that the configured ISI was not found in the input stream. |
| 1.3.6.1.4.1.9986.3.23.1.2.30 | Tabledvbs2xisiTable | not-accessible | current | Lists ISIs detected in the input signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.30.1 | Rowdvbs2xisiEntry | not-accessible | current | Each entry shows an ISI detected in the signal. |
| 1.3.6.1.4.1.9986.3.23.1.2.30.1.1 | Columndvbsx2isiIndex | not-accessible | current | Identifies a DVB-S2X ISI instance. |
| 1.3.6.1.4.1.9986.3.23.1.2.30.1.2 | Columndvbs2xisiNumber | read-only | current | Shows an ISI detected in the multistream signal. |
| 1.3.6.1.4.1.9986.3.23.1.3 | NodeconditionalAccessObjs | |||
| 1.3.6.1.4.1.9986.3.23.1.3.1 | TablebissinterfaceTable | not-accessible | current | Configuration and status for the BISS descrambling engine. |
| 1.3.6.1.4.1.9986.3.23.1.3.1.1 | RowbissinterfaceEntry | not-accessible | current | BISS Interface Table Entry |
| 1.3.6.1.4.1.9986.3.23.1.3.1.1.1 | ColumnbissinterfaceIndex | not-accessible | current | The index of the BISS engine (currently always set to 1). |
| 1.3.6.1.4.1.9986.3.23.1.3.1.1.2 | ColumnbissinterfaceMode | read-write | current | Controls how keys and services are selected for descrambling. |
| 1.3.6.1.4.1.9986.3.23.1.3.1.1.3 | ColumnbissinterfaceConflictingPidsCount | read-only | obsolete | OBSOLETE |
| 1.3.6.1.4.1.9986.3.23.1.3.1.1.4 | ColumnbissinterfaceConflictingPidsCond | read-only | current | Indicates whether or not a PID is configured to be descrambled with two or more different BISS keys. |
| 1.3.6.1.4.1.9986.3.23.1.3.1.1.5 | ColumnbissinterfaceServiceNotFoundCond | read-only | current | Indicates whether or not a service selected for descrambling is present in the transport stream. Applies only in Selected Services mode. |
| 1.3.6.1.4.1.9986.3.23.1.3.1.1.6 | ColumnbissinterfaceSelectedKey | read-write | current | The index of the BISS key from the BissService table to use for descrambling in TS and Decoded PIDs modes. |
| 1.3.6.1.4.1.9986.3.23.1.3.2 | TablebissserviceTable | not-accessible | current | A keyring of BISS keys available for use in descrambling. |
| 1.3.6.1.4.1.9986.3.23.1.3.2.1 | RowbissserviceEntry | not-accessible | current | BISS Service Key Table Entry |
| 1.3.6.1.4.1.9986.3.23.1.3.2.1.1 | ColumnbissserviceIndex | not-accessible | current | The index of the BISS engine (currently always set to 1). |
| 1.3.6.1.4.1.9986.3.23.1.3.2.1.2 | ColumnbissserviceState | read-write | deprecated | Configure the enabled state of BISS descrambling. DEPRECATED: No longer used in newer software. Set bissinterfaceMode to Disabled or remove selected services i… |
| 1.3.6.1.4.1.9986.3.23.1.3.2.1.3 | ColumnbissserviceBissMode | read-write | current | Configures the BISS key mode. |
| 1.3.6.1.4.1.9986.3.23.1.3.2.1.4 | ColumnbissserviceMode1SessionWord | read-write | current | Configures the BISS Mode 1 session word. |
| 1.3.6.1.4.1.9986.3.23.1.3.2.1.5 | ColumnbissserviceModeESessionWord | read-write | current | Configures the BISS Mode E session word. |
| 1.3.6.1.4.1.9986.3.23.1.3.2.1.6 | ColumnbissserviceModeEInjectedId | read-write | current | Configures the BISS Mode E injected ID. |
| 1.3.6.1.4.1.9986.3.23.1.3.2.1.7 | ColumnbissserviceIsSessionWordSet | read-only | current | Shows whether the BISS session word is set. |
| 1.3.6.1.4.1.9986.3.23.1.3.2.1.8 | ColumnbissserviceBissGroup | not-accessible | current | The key's index in the keyring. |
| 1.3.6.1.4.1.9986.3.23.1.3.2.1.9 | ColumnbissserviceAlias | read-write | current | A friendly name used to identify the key. |
| 1.3.6.1.4.1.9986.3.23.1.3.2.1.10 | ColumnbissserviceBiss2Mode | read-write | current | Configures the BISS key mode. |
| 1.3.6.1.4.1.9986.3.23.1.3.3 | TablebissSelectedServiceTable | not-accessible | current | Table for configuring which services to descramble in Selected Services mode. |
| 1.3.6.1.4.1.9986.3.23.1.3.3.1 | RowbissSelectedServiceEntry | not-accessible | current | BISS Selected Service Table Entry |
| 1.3.6.1.4.1.9986.3.23.1.3.3.1.1 | ColumnbissselectedserviceIndex | not-accessible | current | The index of the BISS engine (currently always set to 1). |
| 1.3.6.1.4.1.9986.3.23.1.3.3.1.2 | ColumnbissselectedserviceBissGroup | not-accessible | current | The index of the key to use to descramble the service (see bissserviceBissGroup). |
| 1.3.6.1.4.1.9986.3.23.1.3.3.1.3 | ColumnbissselectedserviceServiceNum | not-accessible | current | The service number of the service to descramble. |
| 1.3.6.1.4.1.9986.3.23.1.3.3.1.4 | ColumnbissselectedserviceRowStatus | read-create | current | The row status variable for the BISS selected service table. |
| 1.3.6.1.4.1.9986.3.23.1.3.3.1.5 | ColumnbissselectedserviceService | read-only | current | Service number of the selected service. |
| 1.3.6.1.4.1.9986.3.23.1.3.4 | TablebissTsTable | not-accessible | deprecated | The BISS TS table has been deprecated in newer software in favor of the bissserviceTable. During the transition period, setting a variable in this table will s… |
| 1.3.6.1.4.1.9986.3.23.1.3.4.1 | RowbissTsEntry | not-accessible | deprecated | BISS TS Table Entry |
| 1.3.6.1.4.1.9986.3.23.1.3.4.1.1 | ColumnbisstsState | read-write | deprecated | Enables/disables the BISS key in single BISS mode. DEPRECATED: Setting this variable has no effect in newer software. |
| 1.3.6.1.4.1.9986.3.23.1.3.4.1.2 | ColumnbisstsBissMode | read-write | deprecated | Configures the BISS key mode. DEPRECATED: Setting this variable in newer software modifies bissserviceBissMode.1.1.1. |
| 1.3.6.1.4.1.9986.3.23.1.3.4.1.3 | ColumnbisstsMode1SessionWord | read-write | deprecated | Configures the BISS Mode 1 session word. DEPRECATED: Setting this variable in newer software modifies bissserviceMode1SessionWord.1.1.1. |
| 1.3.6.1.4.1.9986.3.23.1.3.4.1.4 | ColumnbisstsModeESessionWord | read-write | deprecated | Configures the BISS Mode E encrypted session word. DEPRECATED: Setting this variable in newer software modifies bissserviceModeESessionWord.1.1.1. |
| 1.3.6.1.4.1.9986.3.23.1.3.4.1.5 | ColumnbisstsModeEInjectedId | read-write | deprecated | Configures the BISS Mode E injected ID. DEPRECATED: Setting this variable in newer software modifies bissserviceModeEInjectedId.1.1.1. |
| 1.3.6.1.4.1.9986.3.23.1.3.4.1.6 | ColumnbisstsIsSessionWordSet | read-only | deprecated | Shows whether the BISS TS session word is set. DEPRECATED: Not valid in newer software. |
| 1.3.6.1.4.1.9986.3.23.1.3.4.1.7 | ColumnbisstsIndex | not-accessible | deprecated | The index of the BISS engine (currently always set to 1). |
| 1.3.6.1.4.1.9986.3.23.1.3.5 | TablecamslotTable | not-accessible | current | CAM slot table. |
| 1.3.6.1.4.1.9986.3.23.1.3.5.1 | RowcamslotEntry | not-accessible | current | CAM slot entry. |
| 1.3.6.1.4.1.9986.3.23.1.3.5.1.1 | ColumncamslotIndex | not-accessible | current | The top or bottom CAM slot in a top/bottom CAM configuration and right or left in a right/left configuration. Top/right slot is 2 and the bottom/left slot is 1. |
| 1.3.6.1.4.1.9986.3.23.1.3.5.1.2 | ColumncamslotState | read-write | current | Setting - Enable/Disable the CAM. |
| 1.3.6.1.4.1.9986.3.23.1.3.5.1.3 | ColumncamslotLabel | read-only | current | Contains a description of the CAM Slot. |
| 1.3.6.1.4.1.9986.3.23.1.3.5.1.4 | ColumncamslotCamName | read-only | current | Status - the CAM name. |
| 1.3.6.1.4.1.9986.3.23.1.3.5.1.5 | ColumncamslotCamNotPresentCond | read-only | current | Enabled CAM Not Present Condition |
| 1.3.6.1.4.1.9986.3.23.1.3.5.1.6 | ColumncamslotManualReset | read-write | current | Commands the CAM be reset. |
| 1.3.6.1.4.1.9986.3.23.1.3.5.1.7 | ColumncamslotResetOccurred | read-only | obsolete | CAM reset reason |
| 1.3.6.1.4.1.9986.3.23.1.3.5.1.8 | ColumncamslotDscrmFailPidList | read-only | current | PID list failed to descramble |
| 1.3.6.1.4.1.9986.3.23.1.3.5.1.9 | ColumncamslotDscrmFailPidListCond | read-only | current | Descramble Failed PID List Condition |
| 1.3.6.1.4.1.9986.3.23.1.3.5.1.10 | ColumncamslotSelectedPidNotPresentCond | read-only | current | Selected PID Not Present Condition |
| 1.3.6.1.4.1.9986.3.23.1.3.5.1.11 | ColumncamslotCauseOfReset | read-only | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.3.5.1.12 | ColumncamslotSelectedServiceNotPresentCond | read-only | current | Selected PID Not Present Condition |
| 1.3.6.1.4.1.9986.3.23.1.3.6 | TablecamselectedpidTable | not-accessible | current | CAM selected PID table. |
| 1.3.6.1.4.1.9986.3.23.1.3.6.1 | RowcamselectedpidEntry | not-accessible | current | CAM selected PID entry. |
| 1.3.6.1.4.1.9986.3.23.1.3.6.1.1 | ColumncamselectedpidPid | read-only | current | List of Selected PIDs in the TS being descrambled in Service Descramble Mode. |
| 1.3.6.1.4.1.9986.3.23.1.3.6.1.2 | ColumncamselectedpidProgramNumber | read-only | current | List of Selected PIDs in the TS being descrambled in Service Descramble Mode. |
| 1.3.6.1.4.1.9986.3.23.1.3.6.1.3 | ColumncamselectedpidPresence | read-only | current | Identifies if the PID that is selected for descrambling is found in the active input transport stream. |
| 1.3.6.1.4.1.9986.3.23.1.3.6.1.4 | ColumncamselectedpidReserved0 | read-only | current | Reserved. |
| 1.3.6.1.4.1.9986.3.23.1.3.6.1.5 | ColumncamselectedpidRowStatus | read-create | current | Use service number 65535 to set a PID without an associated service. All other service numbers between 1 and 65534 will associate with the PID. |
| 1.3.6.1.4.1.9986.3.23.1.3.7 | TablecamoptTable | not-accessible | current | CAM Opt table. |
| 1.3.6.1.4.1.9986.3.23.1.3.7.1 | RowcamoptEntry | not-accessible | current | CAM Opt entry. |
| 1.3.6.1.4.1.9986.3.23.1.3.7.1.1 | ColumncamoptIndex | not-accessible | current | Identifies the CAM entry. |
| 1.3.6.1.4.1.9986.3.23.1.3.7.1.2 | ColumncamoptMode | read-write | current | Setting - Use selected pids or selected services. |
| 1.3.6.1.4.1.9986.3.23.1.3.8 | TablecamselectedserviceTable | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.3.8.1 | RowcamselectedserviceEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.3.8.1.1 | ColumncamselectedserviceProgramNumber | read-only | current | List of Selected Programs in the TS to be descrambled in Service Descrambling Mode. |
| 1.3.6.1.4.1.9986.3.23.1.3.8.1.2 | ColumncamselectedserviceRowStatus | read-create | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.3.8.1.3 | ColumncamselectedservicePresence | read-only | current | Identifies if the Program that is selected for descrambling is found in the active input transport stream. |
| 1.3.6.1.4.1.9986.3.23.1.4 | NodeserviceObjs | |||
| 1.3.6.1.4.1.9986.3.23.1.4.1 | NodeserviceSelectionObjs | |||
| 1.3.6.1.4.1.9986.3.23.1.4.1.1 | NodesiObjs | |||
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.1 | TablesiserviceTable | not-accessible | current | SI Service table. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.1.1 | RowsiserviceEntry | not-accessible | current | SI service entry. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.1.1.1 | ColumnsiserviceNum | read-only | current | Service Number of the service. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.1.1.2 | ColumnsiserviceName | read-only | current | Service name associated with the service. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.1.1.3 | ColumnsiservicePcrPid | read-only | current | PCR Pid associated with the service. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.1.1.4 | ColumnsiserviceScrambled | read-only | current | Shows whether the service is scrambled or not. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.2 | TablesiprogramTable | not-accessible | current | SI Program table. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.2.1 | RowsiprogramEntry | not-accessible | current | SI Program entry. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.2.1.1 | ColumnsiprogramCount | read-only | current | Shows the number of programs in the PAT. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.3 | TablesivideoTable | not-accessible | current | SI Video table. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.3.1 | RowsivideoEntry | not-accessible | current | SI Video entry. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.3.1.1 | ColumnsivideoSrvNum | read-only | current | Service number matching the video PID found in the Transport Stream |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.3.1.2 | ColumnsivideoPid | read-only | current | Video PID found in the Transport Stream |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.3.1.3 | ColumnsivideoType | read-only | current | Displays video compression standard of the associated video PID. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.4 | TablesiaudioTable | not-accessible | current | SI Audio table. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.4.1 | RowsiaudioEntry | not-accessible | current | SI Audio entry. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.4.1.1 | ColumnsiaudioSrvNum | read-only | current | Service number matching the audio PID found in the Transport Stream |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.4.1.2 | ColumnsiaudioPid | read-only | current | Audio PID found in the Transport Stream |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.4.1.3 | ColumnsiaudioType | read-only | current | Displays audio compression standard of the associated audio PID. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.4.1.4 | ColumnsiaudioLanguage | read-only | current | Indicates language for the associated audio PID. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.4.1.5 | ColumnsiaudioBitrate | read-only | current | Bitrate for the associated audio PID, bits per-second. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.4.1.6 | ColumnsiaudioCodingMode | read-only | current | Coding mode for the associated audio PID. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.5 | TablesidvbsubtitleinfoTable | not-accessible | current | SI DVB subtitle info table. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.5.1 | RowsidvbsubtitleinfoEntry | not-accessible | current | SI DVB subtitle info entry. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.5.1.1 | ColumnsidvbsubtitleinfoCompPageId | read-only | current | The Composition Page Id |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.5.1.2 | ColumnsidvbsubtitleinfoAncPageId | read-only | current | The Ancillary Page Id |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.5.1.3 | ColumnsidvbsubtitleinfoSrvNum | read-only | current | Service number matching the subtitle PID found in the Transport Stream |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.5.1.4 | ColumnsidvbsubtitleinfoLang | read-write | current | The Langage Code String. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.6 | TablesidvbsubtitlesTable | not-accessible | current | SI DVB Subtitles table. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.6.1 | RowsidvbsubtitlesEntry | not-accessible | current | SI DVB Subtitles entry. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.6.1.1 | ColumnsidvbsubtitlesSrvNum | read-only | current | Service number matching the subtitle PID found in the Transport Stream |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.6.1.2 | ColumnsidvbsubtitlesPid | read-only | current | Subtitle PID found in the Transport Stream |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.7 | TablesivbiTable | not-accessible | current | SI VBI table. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.7.1 | RowsivbiEntry | not-accessible | current | SI VBI entry. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.7.1.1 | ColumnsivbiSrvNum | read-only | current | Service number matching the VBI PID found in the Transport Stream |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.7.1.2 | ColumnsivbiPid | read-only | current | VBI PID found in the Transport Stream |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.7.1.3 | ColumnsivbiType | read-only | current | VBI type for the associated PID. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.8 | TablesiotherTable | not-accessible | current | SI other table. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.8.1 | RowsiotherEntry | not-accessible | current | SI other entry. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.8.1.1 | ColumnsiotherSrvNum | read-only | current | Service number matching the 'other' PID found in the Transport Stream |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.8.1.2 | ColumnsiotherPid | read-only | current | 'Other' PIDs found in the Transport Stream |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.8.1.3 | ColumnsiotherStreamType | read-only | current | Stream type for the associated 'other' PID's in the TS. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.8.1.4 | ColumnsiotherStreamTypeDesc | read-only | current | Stream type string description for the associated 'other' PID. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.9 | TablesiTsTable | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.9.1 | RowsiTsEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.4.1.1.9.1.1 | ColumnsiTsId | read-only | current | The ID of the transport stream. |
| 1.3.6.1.4.1.9986.3.23.1.5 | NodetsOutputObjs | |||
| 1.3.6.1.4.1.9986.3.23.1.5.1 | TabletsoutputsrcTable | not-accessible | current | TS output source table. |
| 1.3.6.1.4.1.9986.3.23.1.5.1.1 | RowtsoutputsrcEntry | not-accessible | current | TS output source entry. |
| 1.3.6.1.4.1.9986.3.23.1.5.1.1.1 | ColumntsoutputsrcTypeIndex | not-accessible | current | Identifies the type of output connector. |
| 1.3.6.1.4.1.9986.3.23.1.5.1.1.2 | ColumntsoutputsrcSlot | not-accessible | current | Identifies the Slot location of the output connector. |
| 1.3.6.1.4.1.9986.3.23.1.5.1.1.3 | ColumntsoutputsrcPortIndex | not-accessible | current | Index of the MPEG/IP transmit or the ASI port. |
| 1.3.6.1.4.1.9986.3.23.1.5.1.1.4 | ColumntsoutputsrcState | read-write | current | Configures the output stream to be enabled or disabled. |
| 1.3.6.1.4.1.9986.3.23.1.5.1.1.5 | ColumntsoutputsrcLabel | read-only | current | Shows source label for available ts outputs. |
| 1.3.6.1.4.1.9986.3.23.1.5.1.1.6 | ColumntsoutputsrcId | read-only | current | Shows the id of the particular ts output src type. |
| 1.3.6.1.4.1.9986.3.23.1.5.1.1.7 | ColumntsoutputsrcType | read-only | current | Shows the type of output src. |
| 1.3.6.1.4.1.9986.3.23.1.5.1.1.8 | ColumntsoutputsrcSource | read-write | current | Configures ts routing for an output. The selection is chosen from instances of outputsrcIndex MIB object. |
| 1.3.6.1.4.1.9986.3.23.1.5.2 | TablempegiptxTable | not-accessible | current | MPEG/IP Transmit table. |
| 1.3.6.1.4.1.9986.3.23.1.5.2.1 | RowmpegiptxEntry | not-accessible | current | MPEG/IP Transmit entry. |
| 1.3.6.1.4.1.9986.3.23.1.5.2.1.1 | ColumnmpegiptxIndex | not-accessible | current | Identifies an MPEG/IP transmit entry. |
| 1.3.6.1.4.1.9986.3.23.1.5.2.1.2 | ColumnmpegiptxNic | read-write | current | Sets MPEG/IP Transmit instance to physical Port 1 or Port 2, when use AG128 or AG26028, Port 1 = Card, Port 2 = Chassis. |
| 1.3.6.1.4.1.9986.3.23.1.5.2.1.3 | ColumnmpegiptxDestinationAddressType | read-only | current | The the type of Internet address of the destination. At this time, only IPv4 is supported. |
| 1.3.6.1.4.1.9986.3.23.1.5.2.1.4 | ColumnmpegiptxDestinationIp | read-write | current | Configures the Destination Internet address. Octets in Hex format example: 239.192.0.200 enter as <#0xEF 0xC0 0x00 0xC8> |
| 1.3.6.1.4.1.9986.3.23.1.5.2.1.5 | ColumnmpegiptxDestinationPort | read-write | current | Configures the destination Internet port. |
| 1.3.6.1.4.1.9986.3.23.1.5.2.1.6 | ColumnmpegiptxSourcePort | read-write | current | Configures the source Internet port. |
| 1.3.6.1.4.1.9986.3.23.1.5.2.1.7 | ColumnmpegiptxTsPackets | read-write | current | Configures the number of transport packets per transmitted IP packet. |
| 1.3.6.1.4.1.9986.3.23.1.5.2.1.8 | ColumnmpegiptxDiffServ | read-write | current | Configures the value placed in the Differentiated Service (DS) field of the IP header. |
| 1.3.6.1.4.1.9986.3.23.1.5.2.1.9 | ColumnmpegiptxUnicastReceiverNotFound | read-only | current | Shows the status of discovery of the destination for a unicast IP stream. |
| 1.3.6.1.4.1.9986.3.23.1.5.2.1.10 | ColumnmpegiptxUnicastRcvNotFoundCond | read-only | current | Unicast Receiver Not Found Error |
| 1.3.6.1.4.1.9986.3.23.1.5.2.1.11 | ColumnmpegiptxUnicastReceiverMACAddr | read-only | current | Displays the MAC Address of the receiving device. |
| 1.3.6.1.4.1.9986.3.23.1.5.2.1.12 | ColumnmpegiptxEncapsulation | read-write | current | MPEG/IP FEC output encapsulation type. |
| 1.3.6.1.4.1.9986.3.23.1.5.3 | TablempegiptxfecTable | not-accessible | current | MPEG/IP FEC output table. |
| 1.3.6.1.4.1.9986.3.23.1.5.3.1 | RowmpegiptxfecEntry | not-accessible | current | MPEG/IP FEC output entry. |
| 1.3.6.1.4.1.9986.3.23.1.5.3.1.1 | ColumnmpegiptxfecIndex | not-accessible | current | Identifies an MPEG/IP FEC output entry. |
| 1.3.6.1.4.1.9986.3.23.1.5.3.1.2 | ColumnmpegiptxfecState | read-write | current | MPEG/IP FEC output state. |
| 1.3.6.1.4.1.9986.3.23.1.5.3.1.3 | ColumnmpegiptxfecColumns | read-write | current | MPEG/IP FEC output columns. |
| 1.3.6.1.4.1.9986.3.23.1.5.3.1.4 | ColumnmpegiptxfecRows | read-write | current | MPEG/IP FEC output rows. |
| 1.3.6.1.4.1.9986.3.23.1.5.4 | NodepidfilterObjs | |||
| 1.3.6.1.4.1.9986.3.23.1.5.4.1 | TablepidfilterTable | not-accessible | current | PID Filter Table. |
| 1.3.6.1.4.1.9986.3.23.1.5.4.1.1 | RowpidfilterEntry | not-accessible | current | PID Filter Entry. |
| 1.3.6.1.4.1.9986.3.23.1.5.4.1.1.1 | ColumnpidfilterIndex | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.5.4.1.1.2 | ColumnpidfilterTsBitrate | read-write | current | The desired bitrate for the current filter. |
| 1.3.6.1.4.1.9986.3.23.1.5.4.1.1.3 | ColumnpidfilterTableProcessingMode | read-write | current | Configure to use either PSI mode(MPEG) or SI mode(DVB). |
| 1.3.6.1.4.1.9986.3.23.1.5.4.1.1.4 | ColumnpidfilterSelectionMode | read-write | current | Configure to filter the using the selected services and PIDs or to filter using the decoded service. |
| 1.3.6.1.4.1.9986.3.23.1.5.4.1.1.5 | ColumnpidfilterPeakBitrate | read-only | current | Shows the bitrate of the filtered PIDs and Services. |
| 1.3.6.1.4.1.9986.3.23.1.5.4.1.1.6 | ColumnpidfilterEmptyOutputCond | read-only | current | PID Filter Empty Output. |
| 1.3.6.1.4.1.9986.3.23.1.5.4.1.1.7 | ColumnpidfilterOverflowCond | read-only | current | PID Filter Overflow Error. |
| 1.3.6.1.4.1.9986.3.23.1.5.4.1.1.8 | ColumnpidfilterSelectionNotPresentCond | read-only | current | PID Filter Selection Not Present. |
| 1.3.6.1.4.1.9986.3.23.1.5.4.2 | TablepidfilterselectedserviceTable | not-accessible | current | PID Filter Selected Service table. |
| 1.3.6.1.4.1.9986.3.23.1.5.4.2.1 | RowpidfilterselectedserviceEntry | not-accessible | current | PID Filter Selected Service entry. |
| 1.3.6.1.4.1.9986.3.23.1.5.4.2.1.1 | ColumnpidfilterserviceRowStatus | read-write | current | The row status variable for the PID Filter selected service table. |
| 1.3.6.1.4.1.9986.3.23.1.5.4.2.1.2 | ColumnpidfilterserviceProgramNumber | read-only | current | Program number index for a program that is to be filtered. |
| 1.3.6.1.4.1.9986.3.23.1.5.4.3 | TablepidfilterselectedpidTable | not-accessible | current | PID Filter Selected PID table. |
| 1.3.6.1.4.1.9986.3.23.1.5.4.3.1 | RowpidfilterselectedpidEntry | not-accessible | current | PID Filter Selected PID entry. |
| 1.3.6.1.4.1.9986.3.23.1.5.4.3.1.1 | ColumnpidfilterpidRowStatus | read-write | current | The row status variable for the PID Filter selected PID table. |
| 1.3.6.1.4.1.9986.3.23.1.5.4.3.1.2 | ColumnpidfilterpidPid | read-only | current | PID index for a PID that is to be filtered. |
| 1.3.6.1.4.1.9986.3.23.1.5.4.4 | ScalarpidfilterconfigPeakBitrateReset | read-write | current | Reset the Peak Bitrates |
| 1.3.6.1.4.1.9986.3.23.1.5.5 | TableoutputsrcTable | not-accessible | current | Output Source table. |
| 1.3.6.1.4.1.9986.3.23.1.5.5.1 | RowoutputsrcEntry | not-accessible | current | Output Source entry. |
| 1.3.6.1.4.1.9986.3.23.1.5.5.1.1 | ColumnoutputsrcIndex | not-accessible | current | Identifies the type of output source index. |
| 1.3.6.1.4.1.9986.3.23.1.5.5.1.2 | ColumnoutputsrcLabel | read-only | current | Shows the Label describing the output source. |
| 1.3.6.1.4.1.9986.3.23.1.5.6 | TablempeTable | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.5.6.1 | RowmpeEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.5.6.1.1 | ColumnmpeTransmitterIndex | not-accessible | current | Index of MPE transmitter. |
| 1.3.6.1.4.1.9986.3.23.1.5.6.1.2 | ColumnmpeState | read-write | current | Configures the enabled state of the MPE data transmission. |
| 1.3.6.1.4.1.9986.3.23.1.5.6.1.3 | ColumnmpeMacFilterState | read-write | current | Configures the enabled state of the MPE MAC filter. |
| 1.3.6.1.4.1.9986.3.23.1.5.6.1.4 | ColumnmpeNic | read-write | current | Configures the connector. |
| 1.3.6.1.4.1.9986.3.23.1.5.6.1.5 | ColumnmpePacketCount | read-only | current | Indicates the number of MPE packets in the stream. |
| 1.3.6.1.4.1.9986.3.23.1.5.6.1.6 | ColumnmpeRestPacketCount | read-write | current | Resets the MPE packet count to 0. |
| 1.3.6.1.4.1.9986.3.23.1.5.6.1.7 | ColumnmpeBitrate | read-only | current | Indicates the bitrate of the MPE data being transmitted. |
| 1.3.6.1.4.1.9986.3.23.1.5.6.1.8 | ColumnmpePid | read-write | current | PID to extract MPE data from. |
| 1.3.6.1.4.1.9986.3.23.1.5.6.1.9 | ColumnmpeDataExtractionErrorCond | read-only | current | MPE data extraction error condition. |
| 1.3.6.1.4.1.9986.3.23.1.5.6.1.10 | ColumnmpeLabel | read-only | current | Shows source label for mpe output. |
| 1.3.6.1.4.1.9986.3.23.1.5.7 | TablempemacTable | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.5.7.1 | RowmpemacEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.9986.3.23.1.5.7.1.1 | ColumnmpemacMacAddress | read-only | current | Configures the MAC address to filter by. |
| 1.3.6.1.4.1.9986.3.23.1.5.7.1.2 | ColumnmpemacRowStatus | read-create | current | The row status variable for the MPE MAC table. |
| 1.3.6.1.4.1.9986.3.23.2 | NodemrdConf | |||
| 1.3.6.1.4.1.9986.3.23.2.1 | GroupmrdObjsGroup | current | Description. | |
| 1.3.6.1.4.1.9986.3.23.2.2 | GroupmrdObsoleteObjsGroup | obsolete | Description. | |
| 1.3.6.1.4.1.9986.3.23.2.3 | GroupmrdDeprecatedObjsGroup | deprecated | Description. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| Action | INTEGER { actionDefault(0), actionGo(1) } | current | Textual Convention to define whether the command has to be acted upon or not. |
| AudioType | INTEGER { audiotypeMpeg1(1), audiotypeMpeg2(2), audiotypeDolbyDigital(3), audiotypeLPCMDolbyE(4), audiotypeDolbyDigitalPlus(5), audiotypeAacAdts(6), audiotypeAacLoas(7), audiotypeNone(8) } | current | Description. |
| CodeRate | INTEGER { unknown(0), cr1By3(1), cr2By5(2), cr1By2(3), cr3By5(4), cr2By3(5), cr3By4(6), cr4By5(7), cr5By6(8), cr7By8(9), cr8By9(10), cr9By10(11) } | current | Description. |
| Enable | INTEGER { enable(1), disable(2) } | current | Description. |
| GuardInterval | INTEGER { unknown(0), gi19By256(1), gi19By128(2), gi1By128(3), gi1By64(4), gi1By32(5), gi1By16(6), gi1By8(7), gi1By4(8) } | current | Description. |
| InputActive | INTEGER { primary(1), backup(2) } | current | Indicates if the primary or backup input is currently the active input. |
| IpConnector | INTEGER { ipconnector1(1), ipconnector2(2) } | current | The physical connector on the MPEG/IP card. |
| License | INTEGER { licenseEnabled(1), licenseDisabled(2) } | current | Description. |
| LinkSpeed | INTEGER { linkspeedAuto(1), linkspeed1000MFull(2), linkspeed1000MHalf(3), linkspeed100MFull(4), linkspeed100MHalf(5), linkspeed10MFull(6), linkspeed10MHalf(7), linkspeedNotApplicable(8) } | current | Defines Port link speed. |
| Lock | INTEGER { lockLocked(1), lockUnlocked(2) } | current | Indicates if the unit has transport stream lock on the active input. |
| Modulation | INTEGER { unknown(0), bpsk(1), dqpsk(2), qpsk(3), qam16(4), qam32(5), qam64(6), qam128(7), qam256(8), qam1024(9), qam4096(10) } | current | Description. |
| PID | Integer32 (0 | 16..8190) | current | Used for Elementary stream PID. |
| PIDIndex | Integer32 (1..8191) | current | Non-zero values to index Elementary stream PIDs. |
| Presence | INTEGER { present(1), notPresent(2), notApplicable(3) } | current | Description. |
| SrvNum | Integer32 (1..65535) | current | Used to indicate the Service Number. |
| Status | INTEGER { statusOk(1), statusFailure(2), statusNotApplicable(3) } | current | Description. |
| Transmission | INTEGER { unknown(0), transmission1K(1), transmission2K(2), transmission4K(3), transmission8K(4), transmission16K(5), transmission32K(6) } | current | Description. |
| VideoType | INTEGER { videotypeUnknown(0), videotypeMPEG1(1), videotypeMPEG2(2), videotypeH264(3) } | current | Description. |