MIB Viewer

SLE-AM-MIB

118 objects
This MIB contains all needed informations about Alarm Manager.
Imported Objects
DASAN-SMIsleMgmt
SLE-TC-MIBSleControlRequestResultType SleControlStatusType
SNMPv2-SMIGauge32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32 zeroDotZero
SNMPv2-TCTEXTUAL-CONVENTION
OIDNameAccessStatusDescription
1.3.6.1.4.1.6296.101.15IdentitysleAlarmMgrThis MIB contains all needed informations about Alarm Manager.
1.3.6.1.4.1.6296.101.15.1ScalarsleAMAlarmTrapNeIdread-onlycurrentuse for NE idendification when alarm(or event) trap system MAC address
1.3.6.1.4.1.6296.101.15.2NodesleAMConfigBase
1.3.6.1.4.1.6296.101.15.2.1TablesleAMConfigTablenot-accessiblecurrentThis table is the class Master Alarm table. It gets populated when system init is done. And it contains all the class alarms supported for the device
1.3.6.1.4.1.6296.101.15.2.1.1RowsleAMConfigEntrynot-accessiblecurrent
1.3.6.1.4.1.6296.101.15.2.1.1.1ColumnsleAMConfigAlarmClassIdread-onlycurrentClass ID starts from 1 to 65535 for the system. And these IDs are defined by alarm-client
1.3.6.1.4.1.6296.101.15.2.1.1.2ColumnsleAMConfigAlarmIdread-onlycurrentAlarm ID Alarm ID starts from 1 to 65535 for the system. And these IDs are defined by alarm-client
1.3.6.1.4.1.6296.101.15.2.1.1.3ColumnsleAMConfigAlarmNameread-writecurrentAlarm Name string
1.3.6.1.4.1.6296.101.15.2.1.1.4ColumnsleAMConfigAlarmSeverityread-onlycurrentAlarm severity: The default severity is pre-defined by each Alarm manager clients critical(1), major(2), minor(3), warning(4), intermediate(5),
1.3.6.1.4.1.6296.101.15.2.1.1.5ColumnsleAMConfigAlarmEnableStateread-onlycurrentAlarm Trap State. Based on the trap state, the alarm will be notified to NMS. If the TRAP STATE is enabled then the alarm will be notified else wont be notifie…
1.3.6.1.4.1.6296.101.15.2.1.1.6ColumnsleAMConfigAlarmRaiseGuardTimeread-onlycurrentAlarm raise Soaking time. When any alarm is raised, this attribute specifies how much time the alarm should be soaked before notifying to Alarm manager range:1…
1.3.6.1.4.1.6296.101.15.2.1.1.7ColumnsleAMConfigAlarmClearGuardTimeread-onlycurrentAlarm clear Soaking time. When any alarm is cleared, this attribute specifies how much time the alarm should be soaked before notifying to Alarm manager range:…
1.3.6.1.4.1.6296.101.15.2.1.1.8ColumnsleAMConfigAlarmLedread-writecurrentAlarm led configuration. Determinde led operate or not, when alarms occur. off(0): led not operate on(1) : led operate
1.3.6.1.4.1.6296.101.15.2.1.1.9ColumnsleAMConfigSpecificIdread-writecurrentAlarm Configuration specific ID(4bytes) classId and alarmID are combinded with a specificID * 1st,2nd Bytes - ClassId * 3rd,4th bytes - alarmID
1.3.6.1.4.1.6296.101.15.2.2NodesleAMConfigControl
1.3.6.1.4.1.6296.101.15.2.2.1ScalarsleAMConfigControlRequestread-writecurrentThe configuration commands, and user can configure functions via setting this entry as proper value.
1.3.6.1.4.1.6296.101.15.2.2.2ScalarsleAMConfigControlStatusread-onlycurrentstatus of user command. User have to check this value as .busy. or .idle. before do setRequest.
1.3.6.1.4.1.6296.101.15.2.2.3ScalarsleAMConfigControlTimerread-writecurrentthe wait-time until setRequest end. In case of short-time command, this value is 0
1.3.6.1.4.1.6296.101.15.2.2.4ScalarsleAMConfigControlTimeStampread-onlycurrentthe time stamp of the last command. (don.t care)
1.3.6.1.4.1.6296.101.15.2.2.5ScalarsleAMConfigControlReqResultread-onlycurrentResult of the last command.
1.3.6.1.4.1.6296.101.15.2.2.6ScalarsleAMConfigControlAlarmClassIdread-writecurrentAlarm Manager Class ID
1.3.6.1.4.1.6296.101.15.2.2.7ScalarsleAMConfigControlAlarmIdread-writecurrentAlarm Manager Alarm Index
1.3.6.1.4.1.6296.101.15.2.2.8ScalarsleAMConfigControlSeverityread-writecurrentAlarm Class Severity critical(1), major(2), minor(3), warning(4), ignore(5), default(6)
1.3.6.1.4.1.6296.101.15.2.2.9ScalarsleAMConfigControlEnableStateread-writecurrentAlarm Trap State. Based on the trap state, the alarm will be notified to NMS. If the TRAP STATE is enabled then the alarm will be notified else wont be notifie…
1.3.6.1.4.1.6296.101.15.2.2.10ScalarsleAMConfigControlRaiseGuardTimeread-writecurrentAlarm Raise Soaking time. When any alarm is raised, this attribute specifies how much time the alarm should be soaked before notifying to Alarm manager range:1…
1.3.6.1.4.1.6296.101.15.2.2.11ScalarsleAMConfigControlClearGuardTimeread-writecurrentAlarm clear Soaking time. When any alarm is cleared, this attribute specifies how much time the alarm should be soaked before notifying to Alarm manager range:…
1.3.6.1.4.1.6296.101.15.2.2.12ScalarsleAMConfigControlLedread-writecurrentAlarm led configuration. Determinde led operate or not, when alarms occur. off(0): led not operate on(1) : led operate
1.3.6.1.4.1.6296.101.15.2.3NodesleAMConfigNotification
1.3.6.1.4.1.6296.101.15.2.3.1NotificationsleAMConfigSeverityChangedcurrentNotification for Alarm severity change
1.3.6.1.4.1.6296.101.15.2.3.2NotificationsleAMConfigEnableStateChangedcurrentNotification for Class Trap State change
1.3.6.1.4.1.6296.101.15.2.3.3NotificationsleAMConfigRaiseGuardTimeChangedcurrentNotification for Raise Soak time change
1.3.6.1.4.1.6296.101.15.2.3.4NotificationsleAMConfigClearGuardTimeChangedcurrentNotification for Clear Soak time change
1.3.6.1.4.1.6296.101.15.2.3.5NotificationsleAMConfigLedChangedcurrentNotification for Alarm led configuration change
1.3.6.1.4.1.6296.101.15.3NodesleAMCurrentBase
1.3.6.1.4.1.6296.101.15.3.1TablesleAMCurrentTablenot-accessiblecurrentThis table contains the current active alarms for the Alarm Class. Each Row in this table gets populated when any Alarm is raised
1.3.6.1.4.1.6296.101.15.3.1.1RowsleAMCurrentEntrynot-accessiblecurrent
1.3.6.1.4.1.6296.101.15.3.1.1.1ColumnsleAMCurrentSeqIdread-onlycurrentalarm sequence id key of current alarm table it generated by alarm-manager automatically
1.3.6.1.4.1.6296.101.15.3.1.1.2ColumnsleAMCurrentAlarmSourceread-onlycurrentalarm location infomation |type|length|value|type|length|value|.... type (1-byte) : alarm location type length(1-byte) : alarm location value length value (len…
1.3.6.1.4.1.6296.101.15.3.1.1.3ColumnsleAMCurrentAlarmClassIdread-onlycurrentClass ID starts from 1 to 65535 for the system. And these IDs are defined by alarm-client
1.3.6.1.4.1.6296.101.15.3.1.1.4ColumnsleAMCurrentAlarmIdread-onlycurrentAlarm ID Alarm ID starts from 1 to 65535 for the system. And these IDs are defined by alarm-client
1.3.6.1.4.1.6296.101.15.3.1.1.5ColumnsleAMCurrentAlarmStatusread-onlycurrentCurrent Alarm State: raised (1), masked(2)
1.3.6.1.4.1.6296.101.15.3.1.1.6ColumnsleAMCurrentAlarmSeverityread-onlycurrentCurrent Alarm Severity: critical(1), major(2), minor(3), warning(4)
1.3.6.1.4.1.6296.101.15.3.1.1.7ColumnsleAMCurrentAlarmReasonread-onlycurrentreasion string
1.3.6.1.4.1.6296.101.15.3.1.1.8ColumnsleAMCurrentTimeAndDateread-onlycurrentCurrent Alarm Time and Date
1.3.6.1.4.1.6296.101.15.3.1.1.9ColumnsleAMCurrentSpecificIdread-writecurrentCurrent Alarm specific ID(4bytes) classId and alarmID are combinded with a specificID * 1st,2nd Bytes - ClassId * 3rd,4th bytes - alarmID
1.3.6.1.4.1.6296.101.15.3.2NodesleAMCurrentControl
1.3.6.1.4.1.6296.101.15.3.2.1ScalarsleAMCurrentControlRequestread-writecurrentThe configuration commands, and user can configure functions via setting this entry as proper value. 1: all current alarm clear 2: current alarm clear by SeqId…
1.3.6.1.4.1.6296.101.15.3.2.2ScalarsleAMCurrentControlStatusread-onlycurrentstatus of user command. User have to check this value as .busy. or .idle. before do setRequest.
1.3.6.1.4.1.6296.101.15.3.2.3ScalarsleAMCurrentControlTimerread-writecurrentthe wait-time until setRequest end. In case of short-time command, this value is 0
1.3.6.1.4.1.6296.101.15.3.2.4ScalarsleAMCurrentControlTimeStampread-onlycurrentthe time stamp of the last command. (don.t care)
1.3.6.1.4.1.6296.101.15.3.2.5ScalarsleAMCurrentControlReqResultread-onlycurrentResult of the last command.
1.3.6.1.4.1.6296.101.15.3.2.6ScalarsleAMCurrentControlSeqIdread-writecurrentcurrent alarmControl Sequence ID.(0, all mcurrent alarm cleared) Valid only if the sleAMHistoryControlRequest value is set to 2(alarmHistoryClearBySeqId).
1.3.6.1.4.1.6296.101.15.3.2.7ScalarsleAMCurrentControlSourceread-writecurrentcurrent alarm clear location infomation |type|length|value|type|length|value|.... type (1-byte) : alarm location type length(1-byte) : alarm location value len…
1.3.6.1.4.1.6296.101.15.3.3NodesleAMCurrentNotification
1.3.6.1.4.1.6296.101.15.3.3.1NotificationsleAMCurrentAlarmClearedcurrentNotification for current alarm clear
1.3.6.1.4.1.6296.101.15.3.3.2NotificationsleAlarmTrapAlarmcurrentNotify Alarm Raise/Clear TRAPS to NMS for each entry in the Table
1.3.6.1.4.1.6296.101.15.3.3.3NotificationsleAlarmTrapEventcurrentNotify Event Occur TRAPS to NMS for each entry in the Table
1.3.6.1.4.1.6296.101.15.4NodesleAMHistoryBase
1.3.6.1.4.1.6296.101.15.4.1TablesleAMHistoryTablenot-accessiblecurrentThis Table is used to for keeping the Alarm History
1.3.6.1.4.1.6296.101.15.4.1.1RowsleAMHistoryEntrynot-accessiblecurrent
1.3.6.1.4.1.6296.101.15.4.1.1.1ColumnsleAMHistorySeqIdread-onlycurrentAlarm History Sequence ID. This sequence Id is maintained based on the TRAP sent.
1.3.6.1.4.1.6296.101.15.4.1.1.2ColumnsleAMHistoryAlarmSourceread-onlycurrent|type|length|value|type|length|value|.... type (1-byte) : alarm location type length(1-byte) : alarm location value length value (length-bytes) : alarm locatio…
1.3.6.1.4.1.6296.101.15.4.1.1.3ColumnsleAMHistoryAlarmClassIdread-onlycurrentClass ID starts from 1 to 65535 for the system. And these IDs are defined by alarm-client
1.3.6.1.4.1.6296.101.15.4.1.1.4ColumnsleAMHistoryAlarmIdread-onlycurrentHistory Alarm ID Alarm ID starts from 1 to 65535 for the system. And these IDs are defined by alarm-client
1.3.6.1.4.1.6296.101.15.4.1.1.5ColumnsleAMHistoryAlarmStatusread-onlycurrentHistory Alarm State: cleared (0), raised (1), masked(2)
1.3.6.1.4.1.6296.101.15.4.1.1.6ColumnsleAMHistoryAlarmSeverityread-onlycurrentHistory alarm Severity critical(1), major(2), minor(3), warning(4)
1.3.6.1.4.1.6296.101.15.4.1.1.7ColumnsleAMHistoryAlarmReasonread-writecurrentHistory alarm Reason string
1.3.6.1.4.1.6296.101.15.4.1.1.8ColumnsleAMHistoryAlarmTimeDateread-onlycurrentHistory Alarm Time and Date
1.3.6.1.4.1.6296.101.15.4.1.1.9ColumnsleAMHistorySpecificIdread-writecurrentAlarm History specific ID(4bytes) classId and alarmID are combinded with a specificID * 1st,2nd Bytes - ClassId * 3rd,4th bytes - alarmID
1.3.6.1.4.1.6296.101.15.4.2NodesleAMHistoryControl
1.3.6.1.4.1.6296.101.15.4.2.1ScalarsleAMHistoryControlRequestread-writecurrentThe configuration commands, and user can configure functions via setting this entry as proper value. clearAlarmHistory : clears the alarms from the History Tab…
1.3.6.1.4.1.6296.101.15.4.2.2ScalarsleAMHistoryControlStatusread-onlycurrentstatus of user command. User have to check this value as .busy. or .idle. before do setRequest.
1.3.6.1.4.1.6296.101.15.4.2.3ScalarsleAMHistoryControlTimerread-writecurrentthe wait-time until setRequest end. In case of short-time command, this value is 0
1.3.6.1.4.1.6296.101.15.4.2.4ScalarsleAMHistoryControlTimeStampread-onlycurrentthe time stamp of the last command. (don.t care)
1.3.6.1.4.1.6296.101.15.4.2.5ScalarsleAMHistoryControlReqResultread-onlycurrentResult of the last command.
1.3.6.1.4.1.6296.101.15.4.2.6ScalarsleAMHistoryControSeqIdread-writecurrentAlarm History Control Sequence ID. Specify cleared history alarm ID (0, all alarm history cleared)
1.3.6.1.4.1.6296.101.15.4.2.7ScalarsleAMHistoryControSourceread-writecurrentalarm history clear location infomation Valid only if the sleAMHistoryControlRequest value is set to 3(alarmHistoryClearBySource). |type|length|value|type|leng…
1.3.6.1.4.1.6296.101.15.4.3NodesleAMHistoryNotification
1.3.6.1.4.1.6296.101.15.4.3.1NotificationsleAMHistoryAlarmClearedcurrentNotification for History Class cleared
1.3.6.1.4.1.6296.101.15.5NodesleAMAcoBase
1.3.6.1.4.1.6296.101.15.5.1NodesleAMAcoInfoEntry
1.3.6.1.4.1.6296.101.15.5.1.1ScalarsleAMAcoInforead-onlycurrentACO control configuration acoOff(1) : buzzer operation enable. acoOn(2) : buzzer operation disable. acoOpr(3) : current buzzer cut.
1.3.6.1.4.1.6296.101.15.5.2NodesleAMAcoControl
1.3.6.1.4.1.6296.101.15.5.2.1ScalarsleAMAcoControlRequestread-writecurrentThe configuration commands, and user can configure functions via setting this entry as proper value.
1.3.6.1.4.1.6296.101.15.5.2.2ScalarsleAMAcogControlStatusread-onlycurrentstatus of user command. User have to check this value as .busy. or .idle. before do setRequest.
1.3.6.1.4.1.6296.101.15.5.2.3ScalarsleAMAcoControlTimerread-writecurrentthe wait-time until setRequest end. In case of short-time command, this value is 0
1.3.6.1.4.1.6296.101.15.5.2.4ScalarsleAMAcoControlTimeStampread-onlycurrentthe time stamp of the last command. (don.t care)
1.3.6.1.4.1.6296.101.15.5.2.5ScalarsleAMAcoControlReqResultread-onlycurrentResult of the last command.
1.3.6.1.4.1.6296.101.15.5.2.6ScalarsleAMAcoControlSetread-writecurrentACO control acoOff(1) : buzzer operation enable. acoOn(2) : buzzer operation disable. acoOpr(3) : current buzzer cut.
1.3.6.1.4.1.6296.101.15.5.3NodesleAMAcoNotification
1.3.6.1.4.1.6296.101.15.5.3.1NotificationsleAMAcoChangedcurrentNotification for Alarm ACO configuration change
1.3.6.1.4.1.6296.101.15.6NodesleAMLedBase
1.3.6.1.4.1.6296.101.15.6.1TablesleAMLedTablenot-accessiblecurrentThis table contains the LED status and configuration.
1.3.6.1.4.1.6296.101.15.6.1.1RowsleAMLedEntrynot-accessiblecurrent
1.3.6.1.4.1.6296.101.15.6.1.1.1ColumnsleAMLedSeverityread-writecurrentLED Alarm Severity critical(1), major(2), minor(3),
1.3.6.1.4.1.6296.101.15.6.1.1.2ColumnsleAMLedSetread-writecurrentACO control configuration acoOff(1) : buzzer operation enable. acoOn(2) : buzzer operation disable. acoOpr(3) : current buzzer cut.
1.3.6.1.4.1.6296.101.15.6.1.1.3ColumnsleAMLedCountread-writecurrentalarm count of the associated led
1.3.6.1.4.1.6296.101.15.6.2NodesleAMLedControl
1.3.6.1.4.1.6296.101.15.6.2.1ScalarsleAMLedControlRequestread-writecurrentThe configuration commands, and user can configure functions via setting this entry as proper value.
1.3.6.1.4.1.6296.101.15.6.2.2ScalarsleAMLedControlStatusread-onlycurrentstatus of user command. User have to check this value as .busy. or .idle. before do setRequest.
1.3.6.1.4.1.6296.101.15.6.2.3ScalarsleAMLedControlTimerread-writecurrentthe wait-time until setRequest end. In case of short-time command, this value is 0
1.3.6.1.4.1.6296.101.15.6.2.4ScalarsleAMLedControlTimeStampread-onlycurrentthe time stamp of the last command. (don.t care)
1.3.6.1.4.1.6296.101.15.6.2.5ScalarsleAMLedControlReqResultread-onlycurrentResult of the last command.
1.3.6.1.4.1.6296.101.15.6.2.6ScalarsleAMLedControlSeverityread-writecurrentLED Alarm Severity critical(1), major(2), minor(3),
1.3.6.1.4.1.6296.101.15.6.2.7ScalarsleAMLedControlSetread-writecurrentLED control configuration ledOff(1) : LED operation disable. ledOn(2) : LED operation enable. ledOpr(3) : current LED off.
1.3.6.1.4.1.6296.101.15.6.3NodesleAMLedNotification
1.3.6.1.4.1.6296.101.15.6.3.1NotificationsleAMLedChangedcurrentNotification for LED configuration change
Type Definitions
NameSyntaxStatusDescription
AlarmStatusINTEGER { cleared(0), raised(1), masked(2), disabled(3), forcedClear(4), event(5), unmasked(6) }currentThis is the status of the alarm. Cleared(0) : Alarm status is cleared Raised(1) : Alarm status is raised. Masked(2) : alarm is suppressed. Disable(3) : Alarm disable Forced-clear(4) : Init alarm Event(5) : Event report …
AMAlarmAcoINTEGER { acoOff(1), acoOn(2), acoOpr(3) }currentACO control configuration acoOff(1) : buzzer operation enable. acoOn(2) : buzzer operation disable. acoOpr(3) : current buzzer cut.
AMAlarmClassIdINTEGER (1..65535)currentalarm class id 1~65535
AMAlarmGuardTimeINTEGER (0..30)currentalarm guard time 1~30 (second) 0, no alarm guard time apply
AMAlarmIdINTEGER (1..65535)currentCurrent Alarm ID 1~65535
AMAlarmLedINTEGER { setLedOff(1), setLedOn(2), oprLed(3) }currentLED control configuration ledOff(1) : LED operation disable. ledOn(2) : LED operation enable. ledOpr(3) : current LED off.
AMAlarmReasonOCTET STRING (SIZE (0..256))currentAlarm reason Description string (include location infomatiln)
AMAlarmSeverityINTEGER { critical(1), major(2), minor(3), warning(4), intermediate(5), default(6) }currentSeverity of Alarm
AMAlarmSrcOCTET STRING (SIZE (68))current|type|length|value|type|length|value|.... type (1-byte) : alarm location type length(1-byte) : alarm location value length value (length-bytes) : alarm location value
AMDateTimeUnsigned32currentTOD integer value
AMTrapStateINTEGER { enable(1), disable(0) }currentThis status explains whether TRAP status is enabled or disabled. Enable(1) : Alarm Trap State is Enabled. Hence TRAPs will be sent for this. Disable(0) : Alarm Trap State is Disabled. So Alarms won't be notified to user.
MIB Viewer