SLE-PM-MIB
72 objects
This MIB contains all needed informations about Performance Manager.
Imported Objects
| DASAN-SMI | sleMgmt |
| SLE-TC-MIB | SleControlRequestResultType SleControlStatusType |
| SNMPv2-SMI | Counter32 Counter64 Gauge32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32 zeroDotZero |
| SNMPv2-TC | TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.6296.101.94 | IdentityslePmMgr | This MIB contains all needed informations about Performance Manager. | ||
| 1.3.6.1.4.1.6296.101.94.1 | ScalarslePmNeId | read-only | current | system MAC address |
| 1.3.6.1.4.1.6296.101.94.2 | NodeslePmConfigBase | |||
| 1.3.6.1.4.1.6296.101.94.2.1 | TableslePmConfigTable | not-accessible | current | This table is the Performance Config table. It gets populated when system init is done. And it contains all the class performance supported for the device |
| 1.3.6.1.4.1.6296.101.94.2.1.1 | RowslePmConfigEntry | not-accessible | current | |
| 1.3.6.1.4.1.6296.101.94.2.1.1.1 | ColumnslePmConfigSeqId | read-only | current | Description. |
| 1.3.6.1.4.1.6296.101.94.2.1.1.2 | ColumnslePmConfigClassId | read-only | current | Class ID starts from 1 to 255 for the system. And these IDs are generated internally |
| 1.3.6.1.4.1.6296.101.94.2.1.1.3 | ColumnslePmConfigPmId | read-only | current | Current PM ID |
| 1.3.6.1.4.1.6296.101.94.2.1.1.4 | ColumnslePmConfigSource | read-only | current | |type|length|value|type|length|value|.... type (1-byte) : PM location type length(1-byte) : PM location value length value (length-bytes) : PM location value |
| 1.3.6.1.4.1.6296.101.94.2.1.1.5 | ColumnslePmConfigTcaStat | read-only | current | TCA status TCA Normal (0) TCA Occur (1) |
| 1.3.6.1.4.1.6296.101.94.2.1.1.6 | ColumnslePmConfigTcaEnable | read-only | current | TCA enable Confguration : enabled or disabled. Enable(1) : TCA State is Enabled. Hence TRAPs will be sent for this. Disable(0) : TCA State is Disabled. So TCA … |
| 1.3.6.1.4.1.6296.101.94.2.1.1.7 | ColumnslePmConfigTh15Min | read-only | current | 15minute Performance TCA threshold configuration count |
| 1.3.6.1.4.1.6296.101.94.2.1.1.8 | ColumnslePmConfigTh1Day | read-write | current | 1day Performance TCA threshold configuration count |
| 1.3.6.1.4.1.6296.101.94.2.2 | NodeslePmConfigControl | |||
| 1.3.6.1.4.1.6296.101.94.2.2.1 | ScalarslePmConfigControlRequest | read-write | current | The configuration commands, and user can configure functions via setting this entry as proper value. |
| 1.3.6.1.4.1.6296.101.94.2.2.2 | ScalarslePmConfigControlStatus | read-only | current | status of user command. User have to check this value as .busy. or .idle. before do setRequest. |
| 1.3.6.1.4.1.6296.101.94.2.2.3 | ScalarslePmConfigControlTimer | read-write | current | the wait-time until setRequest end. In case of short-time command, this value is 0 |
| 1.3.6.1.4.1.6296.101.94.2.2.4 | ScalarslePmConfigControlTimeStamp | read-only | current | the time stamp of the last command. (don.t care) |
| 1.3.6.1.4.1.6296.101.94.2.2.5 | ScalarslePmConfigControlReqResult | read-only | current | Result of the last command. |
| 1.3.6.1.4.1.6296.101.94.2.2.6 | ScalarslePmConfigControlSeqId | read-write | current | PM Manager Class ID |
| 1.3.6.1.4.1.6296.101.94.2.2.7 | ScalarslePmConfigControlTcaEnable | read-write | current | TCA enable Confguration : enabled or disabled. Enable(1) : TCA State is Enabled. Hence TRAPs will be sent for this. Disable(0) : TCA State is Disabled. So TCA … |
| 1.3.6.1.4.1.6296.101.94.2.2.8 | ScalarslePmConfigControlTh15Min | read-write | current | 15minute Performance TCA threshold configuration count |
| 1.3.6.1.4.1.6296.101.94.2.2.9 | ScalarslePmConfigControlTh1Day | read-write | current | 1day Performance TCA threshold configuration count |
| 1.3.6.1.4.1.6296.101.94.2.3 | NodeslePmConfigNotification | |||
| 1.3.6.1.4.1.6296.101.94.2.3.1 | NotificationslePmConfigTcaEnableChanged | current | Notification for Tca Enable change | |
| 1.3.6.1.4.1.6296.101.94.2.3.2 | NotificationslePmConfigTh15MinChanged | current | Notification for 15minute theshold change | |
| 1.3.6.1.4.1.6296.101.94.2.3.3 | NotificationslePmConfigTh1DayChanged | current | Notification for 1day theshold change | |
| 1.3.6.1.4.1.6296.101.94.3 | NodeslePmCurrentBase | |||
| 1.3.6.1.4.1.6296.101.94.3.1 | TableslePmCurrentTable | not-accessible | current | This table contains the current PM count. |
| 1.3.6.1.4.1.6296.101.94.3.1.1 | RowslePmCurrentEntry | not-accessible | current | |
| 1.3.6.1.4.1.6296.101.94.3.1.1.1 | ColumnslePmCurrentSeqId | read-only | current | Description. |
| 1.3.6.1.4.1.6296.101.94.3.1.1.2 | ColumnslePmCurrentClassId | read-only | current | Current Class ID |
| 1.3.6.1.4.1.6296.101.94.3.1.1.3 | ColumnslePmCurrentPmId | read-only | current | Current PM ID |
| 1.3.6.1.4.1.6296.101.94.3.1.1.4 | ColumnslePmCurrentSource | read-only | current | |type|length|value|type|length|value|.... type (1-byte) : PM location type length(1-byte) : PM location value length value (length-bytes) : PM location value |
| 1.3.6.1.4.1.6296.101.94.3.1.1.5 | ColumnslePmCurrentTerm | read-write | current | Description. |
| 1.3.6.1.4.1.6296.101.94.3.1.1.6 | ColumnslePmCurrentPmCount | read-only | current | Current Performance count |
| 1.3.6.1.4.1.6296.101.94.3.1.1.7 | ColumnslePmCurrentAccSecond | read-only | current | Current Performance data accumulation seconds(count) |
| 1.3.6.1.4.1.6296.101.94.3.1.1.8 | ColumnslePmCurrentTcaStat | read-only | current | TCA status TCA Normal (0) TCA Occur (1) |
| 1.3.6.1.4.1.6296.101.94.3.1.1.9 | ColumnslePmCurrentTcaTime | read-only | current | Current PM Time and Date |
| 1.3.6.1.4.1.6296.101.94.3.2 | NodeslePmCurrentControl | |||
| 1.3.6.1.4.1.6296.101.94.3.2.1 | ScalarslePmCurrentControlRequest | read-write | current | The configuration commands, and user can configure functions via setting this entry as proper value. clearCurrentPm(1): Clears the current Performance count (b… |
| 1.3.6.1.4.1.6296.101.94.3.2.2 | ScalarslePmCurrentControlStatus | read-only | current | status of user command. User have to check this value as .busy. or .idle. before do setRequest. |
| 1.3.6.1.4.1.6296.101.94.3.2.3 | ScalarslePmCurrentControlTimer | read-write | current | the wait-time until setRequest end. In case of short-time command, this value is 0 |
| 1.3.6.1.4.1.6296.101.94.3.2.4 | ScalarslePmCurrentControlTimeStamp | read-only | current | the time stamp of the last command. (don.t care) |
| 1.3.6.1.4.1.6296.101.94.3.2.5 | ScalarslePmCurrentControlReqResult | read-only | current | Result of the last command. |
| 1.3.6.1.4.1.6296.101.94.3.3 | NodeslePmCurrentNotification | |||
| 1.3.6.1.4.1.6296.101.94.3.3.1 | NotificationslePmCurrentPmCleared | current | Notification for current PM clear | |
| 1.3.6.1.4.1.6296.101.94.4 | NodeslePMHistoryBase | |||
| 1.3.6.1.4.1.6296.101.94.4.1 | TableslePmHistoryTable | not-accessible | current | This Table is used to for keeping the PM History |
| 1.3.6.1.4.1.6296.101.94.4.1.1 | RowslePmHistoryEntry | not-accessible | current | |
| 1.3.6.1.4.1.6296.101.94.4.1.1.1 | ColumnslePmHistorySeqId | read-only | current | Description. |
| 1.3.6.1.4.1.6296.101.94.4.1.1.2 | ColumnslePmHistoryClassId | read-only | current | History Class ID. |
| 1.3.6.1.4.1.6296.101.94.4.1.1.3 | ColumnslePmHistoryPmId | read-only | current | History PM Id |
| 1.3.6.1.4.1.6296.101.94.4.1.1.4 | ColumnslePmHistoryPmSource | read-only | current | |type|length|value|type|length|value|.... type (1-byte) : PM location type length(1-byte) : PM location value length value (length-bytes) : PM location value |
| 1.3.6.1.4.1.6296.101.94.4.1.1.5 | ColumnslePmHistoryTerm | read-only | current | Description. |
| 1.3.6.1.4.1.6296.101.94.4.1.1.6 | ColumnslePmHistoryIndex | read-only | current | History Index: 15min : 1 ~ 96, 1-day : 1 ~ 7 |
| 1.3.6.1.4.1.6296.101.94.4.1.1.7 | ColumnslePmHistoryPmCount | read-only | current | History Performance count |
| 1.3.6.1.4.1.6296.101.94.4.1.1.8 | ColumnslePmHistoryAccCount | read-write | current | Description. |
| 1.3.6.1.4.1.6296.101.94.4.1.1.9 | ColumnslePmHistoryStartTime | read-only | current | Description. |
| 1.3.6.1.4.1.6296.101.94.4.2 | NodeslePmHistoryControl | |||
| 1.3.6.1.4.1.6296.101.94.4.2.1 | ScalarslePmHistoryControlRequest | read-write | current | The configuration commands, and user can configure functions via setting this entry as proper value. clearPmHistory : clears all the PM History Table |
| 1.3.6.1.4.1.6296.101.94.4.2.2 | ScalarslePmHistoryControlStatus | read-only | current | status of user command. User have to check this value as .busy. or .idle. before do setRequest. |
| 1.3.6.1.4.1.6296.101.94.4.2.3 | ScalarslePmHistoryControlTimer | read-write | current | the wait-time until setRequest end. In case of short-time command, this value is 0 |
| 1.3.6.1.4.1.6296.101.94.4.2.4 | ScalarslePmHistoryControlTimeStamp | read-only | current | the time stamp of the last command. (don.t care) |
| 1.3.6.1.4.1.6296.101.94.4.2.5 | ScalarslePmHistoryControlReqResult | read-only | current | Result of the last command. |
| 1.3.6.1.4.1.6296.101.94.4.3 | NodeslePmHistoryNotification | |||
| 1.3.6.1.4.1.6296.101.94.4.3.1 | NotificationslePmHistoryPmCleared | current | Notification for PM History cleared |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| PmClassId | INTEGER (1..65535) | current | Description. |
| PmDateTime | Unsigned32 | current | TOD integer value |
| PmId | INTEGER (1..65535) | current | Current PM ID |
| PmSrc | OCTET STRING (SIZE (68)) | current | |type|length|value|type|length|value|.... type (1-byte) : PM location type length(1-byte) : PM location value length value (length-bytes) : PM location value |
| PmTcaState | INTEGER { enable(1), disable(0) } | current | This status explains whether TRAP status is enabled or disabled. Enable(1) : TCA State is Enabled. Hence TRAPs will be sent for this. Disable(0) : TCA State is Disabled. So TCA won't be notified to user. |