SMC6152L2-MIB
651 objects
The MIB module for SMC6152L2.
Imported Objects
| BRIDGE-MIB | BridgeId dot1dStpPort dot1dStpPortEntry MacAddress Timeout |
| IF-MIB | ifIndex InterfaceIndex |
| INET-ADDRESS-MIB | InetAddress InetAddressType |
| P-BRIDGE-MIB | EnabledStatus |
| Q-BRIDGE-MIB | PortList VlanIndex |
| SNMPv2-SMI | Counter32 enterprises Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | DisplayString RowStatus TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.202 | Nodesmc | |||
| 1.3.6.1.4.1.202.20 | NodesmcSwitches | |||
| 1.3.6.1.4.1.202.20.66 | Identitysmc6152L2MIB | The MIB module for SMC6152L2. | ||
| 1.3.6.1.4.1.202.20.66.1 | Nodesmc6152L2MIBObjects | |||
| 1.3.6.1.4.1.202.20.66.1.1 | NodeswitchMgt | |||
| 1.3.6.1.4.1.202.20.66.1.1.1 | ScalarswitchManagementVlan | read-write | current | The VLAN on which management is done. |
| 1.3.6.1.4.1.202.20.66.1.1.2 | ScalarswitchNumber | read-only | current | The total number of switches present on this system. |
| 1.3.6.1.4.1.202.20.66.1.1.3 | TableswitchInfoTable | not-accessible | current | Table of descriptive and status information about the switch units in this system. |
| 1.3.6.1.4.1.202.20.66.1.1.3.1 | RowswitchInfoEntry | not-accessible | current | Table providing descriptions and status information for switch units. |
| 1.3.6.1.4.1.202.20.66.1.1.3.1.1 | ColumnswUnitIndex | not-accessible | current | This object identifies the switch within the system for which this entry contains information. This value can never be greater than switchNumber. |
| 1.3.6.1.4.1.202.20.66.1.1.3.1.2 | ColumnswHardwareVer | read-only | current | Hardware version of the main board. |
| 1.3.6.1.4.1.202.20.66.1.1.3.1.3 | ColumnswMicrocodeVer | read-only | current | Microcode version of the main board. |
| 1.3.6.1.4.1.202.20.66.1.1.3.1.4 | ColumnswLoaderVer | read-only | current | Loader version of the main board. |
| 1.3.6.1.4.1.202.20.66.1.1.3.1.5 | ColumnswBootRomVer | read-only | current | Boot ROM code version of the main board. |
| 1.3.6.1.4.1.202.20.66.1.1.3.1.6 | ColumnswOpCodeVer | read-only | current | Operation code version of the main board. |
| 1.3.6.1.4.1.202.20.66.1.1.3.1.7 | ColumnswPortNumber | read-only | current | The number of ports on this switch. |
| 1.3.6.1.4.1.202.20.66.1.1.3.1.8 | ColumnswPowerStatus | read-only | current | Indicates the switch using internalPower(1), redundantPower(2) or both(3) |
| 1.3.6.1.4.1.202.20.66.1.1.3.1.9 | ColumnswRoleInSystem | read-only | current | Indicates the switch is master(1), backupMaster(2) or slave(3) in this system. |
| 1.3.6.1.4.1.202.20.66.1.1.3.1.10 | ColumnswSerialNumber | read-only | current | Serial number of the switch. |
| 1.3.6.1.4.1.202.20.66.1.1.3.1.13 | ColumnswServiceTag | read-only | current | Service tag serial-number of the switch. |
| 1.3.6.1.4.1.202.20.66.1.1.3.1.14 | ColumnswModelNumber | read-only | current | Model number of the switch. |
| 1.3.6.1.4.1.202.20.66.1.1.3.1.15 | ColumnswEpldVer | read-only | current | The EPLD version of the switch. |
| 1.3.6.1.4.1.202.20.66.1.1.4 | ScalarswitchOperState | read-only | current | Global operation state of the switch. |
| 1.3.6.1.4.1.202.20.66.1.1.5 | NodeswitchProductId | |||
| 1.3.6.1.4.1.202.20.66.1.1.5.1 | ScalarswProdName | read-only | current | The product name of this switch. |
| 1.3.6.1.4.1.202.20.66.1.1.5.2 | ScalarswProdManufacturer | read-only | current | The product manufacturer of this switch. |
| 1.3.6.1.4.1.202.20.66.1.1.5.3 | ScalarswProdDescription | read-only | current | The product description of this switch. |
| 1.3.6.1.4.1.202.20.66.1.1.5.4 | ScalarswProdVersion | read-only | current | The runtime code version of this switch. |
| 1.3.6.1.4.1.202.20.66.1.1.5.5 | ScalarswProdUrl | read-only | current | The URL of this switch, which we can connect through a web browser. |
| 1.3.6.1.4.1.202.20.66.1.1.5.6 | ScalarswIdentifier | read-only | current | A unique identifier of which switch in the chassis is currently being looked at. |
| 1.3.6.1.4.1.202.20.66.1.1.5.7 | ScalarswChassisServiceTag | read-only | current | The service tag of the chassis this switch resides in. |
| 1.3.6.1.4.1.202.20.66.1.1.6 | TableswitchIndivPowerTable | not-accessible | current | Table about the status of individual powers. |
| 1.3.6.1.4.1.202.20.66.1.1.6.1 | RowswitchIndivPowerEntry | not-accessible | current | Table about the status of individual power. |
| 1.3.6.1.4.1.202.20.66.1.1.6.1.1 | ColumnswIndivPowerUnitIndex | accessible-for-notify | current | This is defined as swUnitIndex. |
| 1.3.6.1.4.1.202.20.66.1.1.6.1.2 | ColumnswIndivPowerIndex | accessible-for-notify | current | 1 means internal power, 2 means external power. |
| 1.3.6.1.4.1.202.20.66.1.1.6.1.3 | ColumnswIndivPowerStatus | read-only | current | notPresent(1) means not present, green(2) means up, red(3) means down. |
| 1.3.6.1.4.1.202.20.66.1.1.7 | ScalarswitchJumboFrameStatus | read-write | current | enable(1) means the Jumbo Frame has enabled, disabled(2) means the Jumbo Frame has disabled. |
| 1.3.6.1.4.1.202.20.66.1.1.8 | NodeamtrMgt | |||
| 1.3.6.1.4.1.202.20.66.1.1.8.3 | ScalaramtrMacAddrAgingStatus | read-write | current | If this is enabled(1), the MAC address table will age out according to its timer. If this is disabled(2), the MAC address table will not age out. |
| 1.3.6.1.4.1.202.20.66.1.2 | NodeportMgt | |||
| 1.3.6.1.4.1.202.20.66.1.2.1 | TableportTable | not-accessible | current | Table of descriptive and status information describing the configuration of each switch port. This table also contains information about each trunk. |
| 1.3.6.1.4.1.202.20.66.1.2.1.1 | RowportEntry | not-accessible | current | An entry in the table, describing the configuration of one switch port or trunk. |
| 1.3.6.1.4.1.202.20.66.1.2.1.1.1 | ColumnportIndex | not-accessible | current | The port and the trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface… |
| 1.3.6.1.4.1.202.20.66.1.2.1.1.2 | ColumnportName | read-write | current | The name of the port or trunk. This is the same as ifAlias in the IF-MIB (RFC2863 or later). |
| 1.3.6.1.4.1.202.20.66.1.2.1.1.3 | ColumnportType | read-only | current | Indicates the port type of the configuration of the switch. |
| 1.3.6.1.4.1.202.20.66.1.2.1.1.4 | ColumnportSpeedDpxCfg | read-write | current | Configures the speed and duplex mode for a port or trunk, according to: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex … |
| 1.3.6.1.4.1.202.20.66.1.2.1.1.5 | ColumnportFlowCtrlCfg | read-write | current | (1) Flow control mechanism is enabled with tx and rx pause mechansim. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDu… |
| 1.3.6.1.4.1.202.20.66.1.2.1.1.6 | ColumnportCapabilities | read-write | current | Port or trunk capabilities. |
| 1.3.6.1.4.1.202.20.66.1.2.1.1.7 | ColumnportAutonegotiation | read-write | current | Whether auto-negotiation is enabled. |
| 1.3.6.1.4.1.202.20.66.1.2.1.1.8 | ColumnportSpeedDpxStatus | read-only | current | The operating speed and duplex mode of the switched port or trunk. If the entry represents a trunk, the speed is that of its individual members unless the memb… |
| 1.3.6.1.4.1.202.20.66.1.2.1.1.9 | ColumnportFlowCtrlStatus | read-only | current | (2) BackPressure flow control mechanism is used. (3) IEEE 802.3 flow control mechanism is used. (4) Flow control mechanism is disabled. If the entry represents… |
| 1.3.6.1.4.1.202.20.66.1.2.1.1.10 | ColumnportTrunkIndex | read-only | current | The trunk to which this port belongs. A value of 0 means that this port does not belong to any trunk. A value greater than zero means that this port belongs to… |
| 1.3.6.1.4.1.202.20.66.1.2.1.1.12 | ColumnportComboForcedMode | read-write | current | This determines the running mode of a combo port. For a non-combo port, this variable has a value of none(1), and setting this variable to none(1) has no effec… |
| 1.3.6.1.4.1.202.20.66.1.3 | NodetrunkMgt | |||
| 1.3.6.1.4.1.202.20.66.1.3.1 | ScalartrunkMaxId | read-only | current | The maximum number for a trunk identifier. |
| 1.3.6.1.4.1.202.20.66.1.3.2 | ScalartrunkValidNumber | read-only | current | The number of valid trunks. |
| 1.3.6.1.4.1.202.20.66.1.3.3 | TabletrunkTable | not-accessible | current | Table describing the configuration and status of each trunk. |
| 1.3.6.1.4.1.202.20.66.1.3.3.1 | RowtrunkEntry | not-accessible | current | An entry describing the configuration and status of a particular trunk. |
| 1.3.6.1.4.1.202.20.66.1.3.3.1.1 | ColumntrunkIndex | not-accessible | current | Identifies the trunk within the switch that is described by the table entry. |
| 1.3.6.1.4.1.202.20.66.1.3.3.1.2 | ColumntrunkPorts | read-create | current | The complete set of ports currently associated with this trunk. |
| 1.3.6.1.4.1.202.20.66.1.3.3.1.3 | ColumntrunkCreation | read-only | current | A value of static(1) means a statically configured trunk. A value of lacp(2) means an LACP-configured trunk. |
| 1.3.6.1.4.1.202.20.66.1.3.3.1.4 | ColumntrunkStatus | read-create | current | Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. A trunk created by LACP cannot be manually destroyed or (re)configured. |
| 1.3.6.1.4.1.202.20.66.1.4 | NodelacpMgt | |||
| 1.3.6.1.4.1.202.20.66.1.4.1 | TablelacpPortTable | not-accessible | current | Table for LACP port configuration. |
| 1.3.6.1.4.1.202.20.66.1.4.1.1 | RowlacpPortEntry | not-accessible | current | Entry for LACP port configuration. While an entry may exist for a particular port, the port may not support LACP and an attempt to enable LACP may result in fa… |
| 1.3.6.1.4.1.202.20.66.1.4.1.1.1 | ColumnlacpPortIndex | not-accessible | current | The port interface of the lacpPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of … |
| 1.3.6.1.4.1.202.20.66.1.4.1.1.2 | ColumnlacpPortStatus | read-write | current | Whether 802.3ad LACP is enabled. |
| 1.3.6.1.4.1.202.20.66.1.5 | NodestaMgt | |||
| 1.3.6.1.4.1.202.20.66.1.5.1 | ScalarstaSystemStatus | read-write | current | Global spanning tree status. (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled. |
| 1.3.6.1.4.1.202.20.66.1.5.2 | TablestaPortTable | not-accessible | current | The table manages port settings for Spanning Tree Protocol 802.1d, 802.1w or 802.1s depending on the value specified by staProtocolType. |
| 1.3.6.1.4.1.202.20.66.1.5.2.1 | RowstaPortEntry | not-accessible | current | The conceptual entry of staPortTable. |
| 1.3.6.1.4.1.202.20.66.1.5.2.1.2 | ColumnstaPortFastForward | read-write | current | Whether fast forwarding is enabled. |
| 1.3.6.1.4.1.202.20.66.1.5.2.1.3 | ColumnstaPortProtocolMigration | read-write | current | When operating in RSTP (version 2) mode, writing true(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effe… |
| 1.3.6.1.4.1.202.20.66.1.5.2.1.4 | ColumnstaPortAdminEdgePort | read-write | current | The administrative value of the edge port parameter. A value of true(1) indicates that this port should be assumed as an edge-port and a value of false(2) indi… |
| 1.3.6.1.4.1.202.20.66.1.5.2.1.5 | ColumnstaPortOperEdgePort | read-only | current | The operational value of the edge port parameter. The object is initialized to the value of staPortAdminEdgePort and is set false when a BPDU is received. |
| 1.3.6.1.4.1.202.20.66.1.5.2.1.6 | ColumnstaPortAdminPointToPoint | read-write | current | The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as… |
| 1.3.6.1.4.1.202.20.66.1.5.2.1.7 | ColumnstaPortOperPointToPoint | read-only | current | The operational point-to-point status of the LAN segment attached to this port. This indicates whether a port is considered to have a point-to-point connection… |
| 1.3.6.1.4.1.202.20.66.1.5.2.1.9 | ColumnstaPortSystemStatus | read-write | current | Per-port spanning tree status. (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled. |
| 1.3.6.1.4.1.202.20.66.1.5.2.1.10 | ColumnstaPortLongAdminPathCost | read-write | current | The admin value of the RSTP path cost or MST external pathcost. The contribution of this port to the path cost (in 32 bits value) of paths towards the spanning… |
| 1.3.6.1.4.1.202.20.66.1.5.2.1.11 | ColumnstaPortLongOperPathCost | read-only | current | The oper value of the RSTP path cost or MST external pathcost. The contribution of this port to the path cost (in 32 bits value) of paths towards the spanning … |
| 1.3.6.1.4.1.202.20.66.1.5.3 | ScalarstaProtocolType | read-write | current | The version of Spanning Tree Protocol the bridge is currently running. The value 'stp(1)' indicates the Spanning Tree Protocol is as specified in IEEE 802.1D,'… |
| 1.3.6.1.4.1.202.20.66.1.5.4 | ScalarstaTxHoldCount | read-write | current | The value used by the Port Transmit state machine to limit the maximum transmission rate. |
| 1.3.6.1.4.1.202.20.66.1.5.5 | ScalarstaPathCostMethod | read-write | current | Indicates the type of spanning tree path cost mode configured on the switch. This mode applies to all instances of the spanning tree protocol running on the sw… |
| 1.3.6.1.4.1.202.20.66.1.7 | NoderestartMgt | |||
| 1.3.6.1.4.1.202.20.66.1.7.1 | ScalarrestartOpCodeFile | read-write | current | Name of op-code file for start-up. |
| 1.3.6.1.4.1.202.20.66.1.7.2 | ScalarrestartConfigFile | read-write | current | Name of configuration file for start-up. |
| 1.3.6.1.4.1.202.20.66.1.7.3 | ScalarrestartControl | read-write | current | Setting this object to warmBoot(2) causes the device to reinitialize itself such that neither the agent configuration nor the protocol entity implementation is… |
| 1.3.6.1.4.1.202.20.66.1.8 | NodemirrorMgt | |||
| 1.3.6.1.4.1.202.20.66.1.8.1 | TablemirrorTable | not-accessible | current | Table for port mirroring, enabling a port to be mirrored to/from another port. Not all ports can be mirrored and limitations may apply as to which ports can be… |
| 1.3.6.1.4.1.202.20.66.1.8.1.1 | RowmirrorEntry | not-accessible | current | The conceptual row of mirrorTable. |
| 1.3.6.1.4.1.202.20.66.1.8.1.1.1 | ColumnmirrorDestinationPort | not-accessible | current | The destination port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the sa… |
| 1.3.6.1.4.1.202.20.66.1.8.1.1.2 | ColumnmirrorSourcePort | not-accessible | current | The source port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same va… |
| 1.3.6.1.4.1.202.20.66.1.8.1.1.3 | ColumnmirrorType | read-create | current | If this value is rx(1), receive packets will be mirrored. If this value is tx(2), transmit packets will be mirrored. If this value is both(3), both receive and… |
| 1.3.6.1.4.1.202.20.66.1.8.1.1.4 | ColumnmirrorStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.202.20.66.1.9 | NodeigmpSnoopMgt | |||
| 1.3.6.1.4.1.202.20.66.1.9.1 | ScalarigmpSnoopStatus | read-write | current | Parameter to enable or disable IGMP snooping on the device. When enabled, the device will examine IGMP packets and set up filters for IGMP ports. |
| 1.3.6.1.4.1.202.20.66.1.9.2 | ScalarigmpSnoopQuerier | read-write | current | Enables (disables) whether the switch acts as an IGMP querier. |
| 1.3.6.1.4.1.202.20.66.1.9.3 | ScalarigmpSnoopQueryCount | read-write | current | The query count from a querier, during which a response is expected from an endstation. If a querier has sent a number of counts defined by igmpSnoopQueryCount… |
| 1.3.6.1.4.1.202.20.66.1.9.4 | ScalarigmpSnoopQueryInterval | read-write | current | The interval (in seconds) between IGMP host-query messages sent by the switch. |
| 1.3.6.1.4.1.202.20.66.1.9.5 | ScalarigmpSnoopQueryMaxResponseTime | read-write | current | The time after a query, during which a response is expected from an endstation. If a querier has sent a number of queries defined by igmpSnoopQueryCount, but a… |
| 1.3.6.1.4.1.202.20.66.1.9.6 | ScalarigmpSnoopRouterPortExpireTime | read-write | current | Sets the time (in seconds) the switch waits after the previous querier has stopped querying before the router port (which received query packets from previous … |
| 1.3.6.1.4.1.202.20.66.1.9.7 | ScalarigmpSnoopVersion | read-write | current | IGMP version snooped |
| 1.3.6.1.4.1.202.20.66.1.9.8 | TableigmpSnoopRouterCurrentTable | not-accessible | current | Table for current router ports. |
| 1.3.6.1.4.1.202.20.66.1.9.8.1 | RowigmpSnoopRouterCurrentEntry | not-accessible | current | Entry for current router ports. |
| 1.3.6.1.4.1.202.20.66.1.9.8.1.1 | ColumnigmpSnoopRouterCurrentVlanIndex | not-accessible | current | The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The e… |
| 1.3.6.1.4.1.202.20.66.1.9.8.1.2 | ColumnigmpSnoopRouterCurrentPorts | read-only | current | The set of ports which are current router ports, including static router ports. Please refer to igmpSnoopRouterStaticTable. |
| 1.3.6.1.4.1.202.20.66.1.9.8.1.3 | ColumnigmpSnoopRouterCurrentStatus | read-only | current | The set of ports which are static router ports. |
| 1.3.6.1.4.1.202.20.66.1.9.9 | TableigmpSnoopRouterStaticTable | not-accessible | current | Table for static router ports. |
| 1.3.6.1.4.1.202.20.66.1.9.9.1 | RowigmpSnoopRouterStaticEntry | not-accessible | current | Entry for static router ports. |
| 1.3.6.1.4.1.202.20.66.1.9.9.1.1 | ColumnigmpSnoopRouterStaticVlanIndex | not-accessible | current | The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The e… |
| 1.3.6.1.4.1.202.20.66.1.9.9.1.2 | ColumnigmpSnoopRouterStaticPorts | read-create | current | The set of ports which are static router ports. |
| 1.3.6.1.4.1.202.20.66.1.9.9.1.3 | ColumnigmpSnoopRouterStaticStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.202.20.66.1.9.10 | TableigmpSnoopMulticastCurrentTable | not-accessible | current | Table for current multicast addresses. |
| 1.3.6.1.4.1.202.20.66.1.9.10.1 | RowigmpSnoopMulticastCurrentEntry | not-accessible | current | Entry for current multicast addresses. |
| 1.3.6.1.4.1.202.20.66.1.9.10.1.1 | ColumnigmpSnoopMulticastCurrentVlanIndex | not-accessible | current | The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The e… |
| 1.3.6.1.4.1.202.20.66.1.9.10.1.2 | ColumnigmpSnoopMulticastCurrentIpAddress | not-accessible | current | IP address of multicast group. |
| 1.3.6.1.4.1.202.20.66.1.9.10.1.3 | ColumnigmpSnoopMulticastCurrentPorts | read-only | current | The set of ports which are members of a multicast group, including static members. Please refer to igmpSnoopMulticastStaticTable. |
| 1.3.6.1.4.1.202.20.66.1.9.10.1.4 | ColumnigmpSnoopMulticastCurrentStatus | read-only | current | The set of ports which are static members. |
| 1.3.6.1.4.1.202.20.66.1.9.11 | TableigmpSnoopMulticastStaticTable | not-accessible | current | Table for static multicast addresses. |
| 1.3.6.1.4.1.202.20.66.1.9.11.1 | RowigmpSnoopMulticastStaticEntry | not-accessible | current | Entry for static multicast addresses. |
| 1.3.6.1.4.1.202.20.66.1.9.11.1.1 | ColumnigmpSnoopMulticastStaticVlanIndex | not-accessible | current | The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The e… |
| 1.3.6.1.4.1.202.20.66.1.9.11.1.2 | ColumnigmpSnoopMulticastStaticIpAddress | not-accessible | current | IP address of multicast group. |
| 1.3.6.1.4.1.202.20.66.1.9.11.1.3 | ColumnigmpSnoopMulticastStaticPorts | read-create | current | The set of ports which are members. |
| 1.3.6.1.4.1.202.20.66.1.9.11.1.4 | ColumnigmpSnoopMulticastStaticStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.202.20.66.1.9.14 | TableigmpSnoopCurrentVlanTable | not-accessible | current | Table for enabling or disabling IGMP snooping per VLAN. |
| 1.3.6.1.4.1.202.20.66.1.9.14.1 | RowigmpSnoopCurrentVlanEntry | not-accessible | current | Entry for enabling or disabling IGMP snooping. |
| 1.3.6.1.4.1.202.20.66.1.9.14.1.1 | ColumnigmpSnoopCurrentVlanIndex | not-accessible | current | Same is dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface. |
| 1.3.6.1.4.1.202.20.66.1.9.14.1.3 | ColumnigmpSnoopCurrentVlanImmediateLeave | read-write | current | The parameter to enable or disable the Immediate-Leave feature on this VLAN. |
| 1.3.6.1.4.1.202.20.66.1.9.15 | ScalarigmpSnoopLeaveProxy | read-write | current | This enables or disables Leave Proxy for IGMP Snooping. |
| 1.3.6.1.4.1.202.20.66.1.9.17 | ScalarigmpSnoopFilterStatus | read-write | current | Parameter to enable or disable IGMP filtering on the device. |
| 1.3.6.1.4.1.202.20.66.1.9.18 | TableigmpSnoopProfileTable | not-accessible | current | The table for configuring the IGMP snooping profile. |
| 1.3.6.1.4.1.202.20.66.1.9.18.1 | RowigmpSnoopProfileEntry | not-accessible | current | The entry for configuring the IGMP snooping profile. |
| 1.3.6.1.4.1.202.20.66.1.9.18.1.1 | ColumnigmpSnoopProfileId | not-accessible | current | The ID of the IGMP snooping profile. |
| 1.3.6.1.4.1.202.20.66.1.9.18.1.2 | ColumnigmpSnoopProfileAction | read-write | current | The access mode of the IGMP snooping profile. |
| 1.3.6.1.4.1.202.20.66.1.9.18.1.3 | ColumnigmpSnoopProfileStatus | read-write | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.202.20.66.1.9.19 | NodeigmpSnoopProfileCtl | |||
| 1.3.6.1.4.1.202.20.66.1.9.19.1 | ScalarigmpSnoopProfileCtlId | read-write | current | The ID of the IGMP snooping profile. |
| 1.3.6.1.4.1.202.20.66.1.9.19.2 | ScalarigmpSnoopProfileCtlInetAddressType | read-write | current | The address type is associated with this agent. Only ipv4(1) type is supported. |
| 1.3.6.1.4.1.202.20.66.1.9.19.3 | ScalarigmpSnoopProfileCtlStartInetAddress | read-write | current | The specified addresses in the start of the controlled IP multicast addresses. |
| 1.3.6.1.4.1.202.20.66.1.9.19.4 | ScalarigmpSnoopProfileCtlEndInetAddress | read-write | current | The specified addresses in the end of the controlled IP multicast addresses. |
| 1.3.6.1.4.1.202.20.66.1.9.19.5 | ScalarigmpSnoopProfileCtlAction | read-write | current | Setting it to create(2) creates the range of the controlled IP multicast addresses. Setting it to destroy(3) destroys the range of the controlled IP multicast … |
| 1.3.6.1.4.1.202.20.66.1.9.20 | TableigmpSnoopProfileRangeTable | not-accessible | current | The table for configuring the range of the IGMP snooping profile. |
| 1.3.6.1.4.1.202.20.66.1.9.20.1 | RowigmpSnoopProfileRangeEntry | not-accessible | current | The entry for configuring the range of the IGMP snooping profile. |
| 1.3.6.1.4.1.202.20.66.1.9.20.1.1 | ColumnigmpSnoopProfileRangeProfileId | not-accessible | current | This is defined as igmpSnoopProfileId. |
| 1.3.6.1.4.1.202.20.66.1.9.20.1.2 | ColumnigmpSnoopProfileRangeInetAddressType | not-accessible | current | The address type is associated with this agent. Only ipv4(1) type is supported. |
| 1.3.6.1.4.1.202.20.66.1.9.20.1.3 | ColumnigmpSnoopProfileRangeStartInetAddress | not-accessible | current | The specified addresses in the start of the controlled IP multicast addresses. |
| 1.3.6.1.4.1.202.20.66.1.9.20.1.4 | ColumnigmpSnoopProfileRangeEndInetAddress | read-only | current | The specified addresses in the end of the controlled IP multicast addresses. |
| 1.3.6.1.4.1.202.20.66.1.9.20.1.5 | ColumnigmpSnoopProfileRangeAction | read-only | current | The access mode of the IGMP snooping profile. |
| 1.3.6.1.4.1.202.20.66.1.9.21 | TableigmpSnoopFilterPortTable | not-accessible | current | Table for port configuration in IGMP filtering. |
| 1.3.6.1.4.1.202.20.66.1.9.21.1 | RowigmpSnoopFilterPortEntry | not-accessible | current | Entry for port configuration in IGMP filtering. |
| 1.3.6.1.4.1.202.20.66.1.9.21.1.1 | ColumnigmpSnoopFilterPortIndex | not-accessible | current | The port and trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface ide… |
| 1.3.6.1.4.1.202.20.66.1.9.21.1.2 | ColumnigmpSnoopFilterPortProfileId | read-write | current | The igmpSnoopProfileEntry identified by a particular value of this index is the same interface identified by the same value of the igmpSnoopProfileId object. I… |
| 1.3.6.1.4.1.202.20.66.1.9.22 | TableigmpSnoopThrottlePortTable | not-accessible | current | Table for port configuration in IGMP throttling. |
| 1.3.6.1.4.1.202.20.66.1.9.22.1 | RowigmpSnoopThrottlePortEntry | not-accessible | current | Entry for port configuration in IGMP throttling. |
| 1.3.6.1.4.1.202.20.66.1.9.22.1.1 | ColumnigmpSnoopThrottlePortIndex | not-accessible | current | The port and trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface ide… |
| 1.3.6.1.4.1.202.20.66.1.9.22.1.2 | ColumnigmpSnoopThrottlePortRunningStatus | read-only | current | Describes the running status of the IGMP throttling to the switch. A value of true(1) indicates the IGMP throttling mechanism is active. A value of false(2) in… |
| 1.3.6.1.4.1.202.20.66.1.9.22.1.3 | ColumnigmpSnoopThrottlePortAction | read-write | current | The action mode of the IGMP throttling. A value of replace(1) means to replace a joined multicast group randomly when an interface receives an IGMP report and … |
| 1.3.6.1.4.1.202.20.66.1.9.22.1.4 | ColumnigmpSnoopThrottlePortMaxGroups | read-write | current | The maximum number of IGMP groups that the interface can join. |
| 1.3.6.1.4.1.202.20.66.1.9.22.1.5 | ColumnigmpSnoopThrottlePortCurrentGroups | read-only | current | The current number of IGMP groups that the interface has joined. |
| 1.3.6.1.4.1.202.20.66.1.10 | NodeipMgt | |||
| 1.3.6.1.4.1.202.20.66.1.10.1 | TablenetConfigTable | not-accessible | current | A table of netConfigEntry. |
| 1.3.6.1.4.1.202.20.66.1.10.1.1 | RownetConfigEntry | not-accessible | current | A set of configuration parameters for a particular network interface on this device. If the device has no network interface, this table is empty. The index is … |
| 1.3.6.1.4.1.202.20.66.1.10.1.1.1 | ColumnnetConfigIfIndex | not-accessible | current | The VLAN interface being used by this table entry. Only the VLAN interfaces which have an IP configured will appear in the table. |
| 1.3.6.1.4.1.202.20.66.1.10.1.1.2 | ColumnnetConfigIPAddress | not-accessible | current | The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask is 0.0.0.0, then wh… |
| 1.3.6.1.4.1.202.20.66.1.10.1.1.3 | ColumnnetConfigSubnetMask | not-accessible | current | The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then … |
| 1.3.6.1.4.1.202.20.66.1.10.1.1.4 | ColumnnetConfigPrimaryInterface | read-create | current | Whether this is a primary interface. |
| 1.3.6.1.4.1.202.20.66.1.10.1.1.5 | ColumnnetConfigUnnumbered | read-only | current | Whether this is an unnumbered interface. |
| 1.3.6.1.4.1.202.20.66.1.10.1.1.6 | ColumnnetConfigStatus | read-create | current | The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: -… |
| 1.3.6.1.4.1.202.20.66.1.10.2 | ScalarnetDefaultGateway | read-write | current | The IP Address of the default gateway. If this value is undefined or unknown, it shall have the value 0.0.0.0. |
| 1.3.6.1.4.1.202.20.66.1.10.3 | ScalaripHttpState | read-write | current | Whether HTTP is enabled. |
| 1.3.6.1.4.1.202.20.66.1.10.4 | ScalaripHttpPort | read-write | current | The port number for HTTP. |
| 1.3.6.1.4.1.202.20.66.1.10.5 | ScalaripDhcpRestart | read-write | current | When set to restart(1) the DHCP server will restart. When read, this value always returns noRestart(2). |
| 1.3.6.1.4.1.202.20.66.1.10.6 | ScalaripHttpsState | read-write | current | Whether HTTPS is enabled. |
| 1.3.6.1.4.1.202.20.66.1.10.7 | ScalaripHttpsPort | read-write | current | The port number for HTTPS. |
| 1.3.6.1.4.1.202.20.66.1.10.11 | NodedhcpMgt | |||
| 1.3.6.1.4.1.202.20.66.1.10.11.1 | NodedhcpClient | |||
| 1.3.6.1.4.1.202.20.66.1.10.11.1.1 | NodedhcpcOptions | |||
| 1.3.6.1.4.1.202.20.66.1.10.11.1.1.1 | TabledhcpcInterfaceTable | not-accessible | current | Table for DHCP client information listed by interface. Depending on the nature of the product, this table may have only one entry(e.g. for the management VLAN)… |
| 1.3.6.1.4.1.202.20.66.1.10.11.1.1.1.1 | RowdhcpcInterfaceEntry | not-accessible | current | Entry for DHCP client information listed by interface. |
| 1.3.6.1.4.1.202.20.66.1.10.11.1.1.1.1.1 | ColumndhcpcIfIndex | not-accessible | current | This is defined by ifIndex in the IF-MIB.(static vlan if index) |
| 1.3.6.1.4.1.202.20.66.1.10.11.1.1.1.1.2 | ColumndhcpcIfClientIdMode | read-write | current | Whether the Client ID is in text mode or in Hex mode. |
| 1.3.6.1.4.1.202.20.66.1.10.11.1.1.1.1.3 | ColumndhcpcIfClientId | read-write | current | The value that the DHCP client sets in the client_id option of DHCPDISCOVER and DHCPREQUEST messages. This value may be used by DHCP servers to uniquely identi… |
| 1.3.6.1.4.1.202.20.66.1.11 | NodebcastStormMgt | |||
| 1.3.6.1.4.1.202.20.66.1.11.1 | TablebcastStormTable | not-accessible | current | Table to manage the control of broadcast storms for ports. |
| 1.3.6.1.4.1.202.20.66.1.11.1.1 | RowbcastStormEntry | not-accessible | current | The conceptual row of bcastStormTable. |
| 1.3.6.1.4.1.202.20.66.1.11.1.1.1 | ColumnbcastStormIfIndex | not-accessible | current | The port and the trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface… |
| 1.3.6.1.4.1.202.20.66.1.11.1.1.2 | ColumnbcastStormStatus | read-write | current | Whether broadcast storm protection is enabled. |
| 1.3.6.1.4.1.202.20.66.1.11.1.1.7 | ColumnbcastStormOctetRateInKilo | read-write | current | Broadcast storm threshold in kilobits per second. If this entry is for a trunk, this is the value for each member port. For a 100 Mbps port, the range is 64 to… |
| 1.3.6.1.4.1.202.20.66.1.12 | NodevlanMgt | |||
| 1.3.6.1.4.1.202.20.66.1.12.1 | TablevlanTable | not-accessible | current | Table for VLAN configuration. |
| 1.3.6.1.4.1.202.20.66.1.12.1.1 | RowvlanEntry | not-accessible | current | Entry for VLAN configuration. |
| 1.3.6.1.4.1.202.20.66.1.12.1.1.1 | ColumnvlanIndex | not-accessible | current | Based on dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface. |
| 1.3.6.1.4.1.202.20.66.1.12.1.1.2 | ColumnvlanAddressMethod | read-write | current | Method to get the IP address. |
| 1.3.6.1.4.1.202.20.66.1.12.2 | TablevlanPortTable | not-accessible | current | Table for port configuration in VLAN. |
| 1.3.6.1.4.1.202.20.66.1.12.2.1 | RowvlanPortEntry | not-accessible | current | Entry for port configuration in VLAN. |
| 1.3.6.1.4.1.202.20.66.1.12.2.1.1 | ColumnvlanPortIndex | not-accessible | current | The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface… |
| 1.3.6.1.4.1.202.20.66.1.12.2.1.2 | ColumnvlanPortMode | read-write | current | This variable sets the 802.1Q VLAN mode. Setting it to hybrid(1) sets a hybrid link. Setting it to dot1qTrunk(2) sets a trunk link. Setting it to access(3) set… |
| 1.3.6.1.4.1.202.20.66.1.12.2.1.3 | ColumnvlanPortPrivateVlanType | read-write | current | The port type defined for private VLAN. |
| 1.3.6.1.4.1.202.20.66.1.12.5 | TableprotocolVlanTable | not-accessible | current | The configuration table which contains the binding entry of the protocol-group and VLANs. |
| 1.3.6.1.4.1.202.20.66.1.12.5.1 | RowprotocolVlanEntry | not-accessible | current | The binding entry of the protocol-group and VLANs. |
| 1.3.6.1.4.1.202.20.66.1.12.5.1.1 | ColumnprotocolVlanGroupId | not-accessible | current | The specified protocol group of a binding entry. |
| 1.3.6.1.4.1.202.20.66.1.12.5.1.2 | ColumnprotocolVlanGroupVid | read-write | current | The vlan index of the binding entry. The vid zero is used to delete the binding entry. |
| 1.3.6.1.4.1.202.20.66.1.13 | NodepriorityMgt | |||
| 1.3.6.1.4.1.202.20.66.1.13.1 | ScalarprioIpPrecDscpStatus | read-write | current | Selects whether no frame priority mapping, IP ToS precedence mapping or DSCP mapping is performed. |
| 1.3.6.1.4.1.202.20.66.1.13.4 | TableprioIpDscpTable | not-accessible | current | Table for IP DSCP priority mapping. |
| 1.3.6.1.4.1.202.20.66.1.13.4.1 | RowprioIpDscpEntry | not-accessible | current | Entry for IP DSCP priority mapping. |
| 1.3.6.1.4.1.202.20.66.1.13.4.1.1 | ColumnprioIpDscpPort | not-accessible | current | The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface… |
| 1.3.6.1.4.1.202.20.66.1.13.4.1.2 | ColumnprioIpDscpValue | not-accessible | current | Value of IP DSCP as specified in the packet header. |
| 1.3.6.1.4.1.202.20.66.1.13.4.1.3 | ColumnprioIpDscpCos | read-write | current | Class of Service as defined by dot1dTrafficClassPriority in the P-BRIDGE-MIB. The prioIpDscpValue value in the same table row will be mapped to this Class of S… |
| 1.3.6.1.4.1.202.20.66.1.13.5 | ScalarprioIpDscpRestoreDefault | read-write | current | Enables the IP DSCP settings of a port to be reset to their defaults. To reset the IP DSCP settings of a port, assign the value of the relevant ifIndex defined… |
| 1.3.6.1.4.1.202.20.66.1.13.8 | NodeprioCopy | |||
| 1.3.6.1.4.1.202.20.66.1.13.8.2 | ScalarprioCopyIpDscp | read-write | current | Action to copy IP DSCP settings from a source port to many destination ports. The first four octets represent an integer for the source port in high-to-low (bi… |
| 1.3.6.1.4.1.202.20.66.1.13.9 | TableprioWrrTable | not-accessible | current | Table for weighted round robin (WRR). |
| 1.3.6.1.4.1.202.20.66.1.13.9.1 | RowprioWrrEntry | not-accessible | current | Entry for weighted round robin (WRR). |
| 1.3.6.1.4.1.202.20.66.1.13.9.1.1 | ColumnprioWrrTrafficClass | not-accessible | current | Traffic class for this entry, as defined in dot1dTrafficClass in the P-BRIDGE-MIB. The actual maximum depends on the hardware, and is equal to dot1dPortNumTraf… |
| 1.3.6.1.4.1.202.20.66.1.13.9.1.2 | ColumnprioWrrWeight | read-write | current | Weight for this entry. |
| 1.3.6.1.4.1.202.20.66.1.13.10 | ScalarprioQueueMode | read-write | current | The global status for the prioQueue. wrr(1),strict(2) |
| 1.3.6.1.4.1.202.20.66.1.14 | NodetrapDestMgt | |||
| 1.3.6.1.4.1.202.20.66.1.14.1 | TabletrapDestTable | not-accessible | current | A list of trap destination entries. |
| 1.3.6.1.4.1.202.20.66.1.14.1.1 | RowtrapDestEntry | not-accessible | current | A destination entry describes the destination IP address, the community string, and SNMP version to use when sending a trap. |
| 1.3.6.1.4.1.202.20.66.1.14.1.1.1 | ColumntrapDestAddress | not-accessible | current | The address to send traps. |
| 1.3.6.1.4.1.202.20.66.1.14.1.1.2 | ColumntrapDestCommunity | read-create | current | A community to which this destination address belongs. |
| 1.3.6.1.4.1.202.20.66.1.14.1.1.3 | ColumntrapDestStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.202.20.66.1.14.1.1.4 | ColumntrapDestVersion | read-create | current | Determines the version of the trap that is to be sent to the trap receiver. If the value is 1, then an SNMP version 1 trap is sent and if the value is 2, an SN… |
| 1.3.6.1.4.1.202.20.66.1.14.1.1.5 | ColumntrapDestUdpPort | read-create | current | Determines the UDP port number that the trap will be sent to. |
| 1.3.6.1.4.1.202.20.66.1.16 | NodeqosMgt | |||
| 1.3.6.1.4.1.202.20.66.1.16.1 | NoderateLimitMgt | |||
| 1.3.6.1.4.1.202.20.66.1.16.1.2 | TablerateLimitPortTable | not-accessible | current | Table for rate limit of each port. |
| 1.3.6.1.4.1.202.20.66.1.16.1.2.1 | RowrateLimitPortEntry | not-accessible | current | Entry for rate limit of each port. |
| 1.3.6.1.4.1.202.20.66.1.16.1.2.1.1 | ColumnrlPortIndex | not-accessible | current | The port and the trunk (including trunk member) interface of the portTable. The interface identified by a particular value of this index is the same interface … |
| 1.3.6.1.4.1.202.20.66.1.16.1.2.1.6 | ColumnrlPortInputStatus | read-write | current | Whether input rate limit is enabled for this port. |
| 1.3.6.1.4.1.202.20.66.1.16.1.2.1.7 | ColumnrlPortOutputStatus | read-write | current | Whether output rate limit is enabled for this port. |
| 1.3.6.1.4.1.202.20.66.1.16.1.2.1.10 | ColumnrlPortInputLimitInKilo | read-write | current | Value of the input rate limit. Its unit is kilobits per second. For a 100 Mbps port, the range is 64 to 100000. For a 1000 Mbps port, the range is 64 to 100000… |
| 1.3.6.1.4.1.202.20.66.1.16.1.2.1.11 | ColumnrlPortOutputLimitInKilo | read-write | current | Value of the output rate limit. Its unit is kilobits per second. For a 100 Mbps port, the range is 64 to 100000. For a 1000 Mbps port, the range is 64 to 10000… |
| 1.3.6.1.4.1.202.20.66.1.16.4 | NodediffServMgt | |||
| 1.3.6.1.4.1.202.20.66.1.16.4.9 | TablediffServPortTable | not-accessible | current | Table for differentiated services on each port. |
| 1.3.6.1.4.1.202.20.66.1.16.4.9.1 | RowdiffServPortEntry | not-accessible | current | Entry for differentiated services on each port. |
| 1.3.6.1.4.1.202.20.66.1.16.4.9.1.1 | ColumndiffServPortIfIndex | not-accessible | current | This object is the interface index of diffServPortEntry. The interface identified by a particular value of this index is the same interface as identified by th… |
| 1.3.6.1.4.1.202.20.66.1.16.4.9.1.2 | ColumndiffServPortPolicyMapIndex | read-write | current | Specifies the policy map binding to the interface. The policy map identified by a particular value of this index is associated with the same DiffServPolicyMapE… |
| 1.3.6.1.4.1.202.20.66.1.16.4.9.1.3 | ColumndiffServPortIngressIpAclIndex | read-write | current | Specifies the ingress IP ACL binding to the interface. The ingress IP ACL identified by a particular value of this index is associated with the same diffServAc… |
| 1.3.6.1.4.1.202.20.66.1.16.4.9.1.4 | ColumndiffServPortIngressMacAclIndex | read-write | current | Specifies the ingress MAC ACL binding to the interface. The ingress MAC ACL identified by a particular value of this index is associated with the same diffServ… |
| 1.3.6.1.4.1.202.20.66.1.16.4.10 | TablediffServPolicyMapTable | not-accessible | current | Table for policy map. |
| 1.3.6.1.4.1.202.20.66.1.16.4.10.1 | RowdiffServPolicyMapEntry | not-accessible | current | Entry for policy map. |
| 1.3.6.1.4.1.202.20.66.1.16.4.10.1.1 | ColumndiffServPolicyMapIndex | not-accessible | current | An index that uniquely identifies an entry in this table. |
| 1.3.6.1.4.1.202.20.66.1.16.4.10.1.2 | ColumndiffServPolicyMapName | read-create | current | The name of this entry. |
| 1.3.6.1.4.1.202.20.66.1.16.4.10.1.3 | ColumndiffServPolicyMapDescription | read-create | current | The description of this entry. |
| 1.3.6.1.4.1.202.20.66.1.16.4.10.1.4 | ColumndiffServPolicyMapElementIndexList | read-only | current | The octet string containes the diffServPolicyMapElementEntry indexes. Two octets express one index and it is represented in network order. This index list indi… |
| 1.3.6.1.4.1.202.20.66.1.16.4.10.1.5 | ColumndiffServPolicyMapStatus | read-create | current | This object is used to create a new row, or modify or delete an existing row, in this table. The status column has six defined values: The status column has si… |
| 1.3.6.1.4.1.202.20.66.1.16.4.11 | NodediffServPolicyMapAttachCtl | |||
| 1.3.6.1.4.1.202.20.66.1.16.4.11.1 | ScalardiffServPolicyMapAttachCtlIndex | read-write | current | Index for attachment control. Specifies the policy map as the target to relate with the policy map element. The policy map identified by a particular value of … |
| 1.3.6.1.4.1.202.20.66.1.16.4.11.2 | ScalardiffServPolicyMapAttachCtlElementIndex | read-write | current | Element Index for attachment control.Specifies the policy map element to relate with the policy map. The policy map element identified by a particular value of… |
| 1.3.6.1.4.1.202.20.66.1.16.4.11.3 | ScalardiffServPolicyMapAttachCtlAction | read-write | current | Action for attachment control. When setting this object to attach(2) to begin the attaching operation, a particular policy map element is attached to a particu… |
| 1.3.6.1.4.1.202.20.66.1.16.4.12 | TablediffServPolicyMapElementTable | not-accessible | current | Table for policy map element. |
| 1.3.6.1.4.1.202.20.66.1.16.4.12.1 | RowdiffServPolicyMapElementEntry | not-accessible | current | Entry for policy map element. |
| 1.3.6.1.4.1.202.20.66.1.16.4.12.1.1 | ColumndiffServPolicyMapElementIndex | not-accessible | current | An index that uniquely identifies an entry in this table. |
| 1.3.6.1.4.1.202.20.66.1.16.4.12.1.2 | ColumndiffServPolicyMapElementClassMapIndex | read-create | current | Specifies the class map binding to this entry. The class map identified by a particular value of this index is associated with the same diffServClassMapEntry a… |
| 1.3.6.1.4.1.202.20.66.1.16.4.12.1.3 | ColumndiffServPolicyMapElementMeterIndex | read-create | current | Specifies the meter binding to this entry. The meter identified by a particular value of this index is associated with the same diffServMeterEntry as identifie… |
| 1.3.6.1.4.1.202.20.66.1.16.4.12.1.4 | ColumndiffServPolicyMapElementActionIndex | read-create | current | Specifies the action binding to this entry. The action identified by a particular value of this index is associated with the same diffServActionEntry as identi… |
| 1.3.6.1.4.1.202.20.66.1.16.4.12.1.5 | ColumndiffServPolicyMapElementStatus | read-create | current | This object is used to create a new row, or modify or delete an existing row, in this table. The status column has six defined values: The status column has si… |
| 1.3.6.1.4.1.202.20.66.1.16.4.13 | TablediffServClassMapTable | not-accessible | current | Table for class map. |
| 1.3.6.1.4.1.202.20.66.1.16.4.13.1 | RowdiffServClassMapEntry | not-accessible | current | Entry for class map. |
| 1.3.6.1.4.1.202.20.66.1.16.4.13.1.1 | ColumndiffServClassMapIndex | not-accessible | current | An index that uniquely identifies an entry in this table. |
| 1.3.6.1.4.1.202.20.66.1.16.4.13.1.2 | ColumndiffServClassMapName | read-create | current | The name of this entry. |
| 1.3.6.1.4.1.202.20.66.1.16.4.13.1.3 | ColumndiffServClassMapDescription | read-create | current | The description of this entry. |
| 1.3.6.1.4.1.202.20.66.1.16.4.13.1.4 | ColumndiffServClassMapMatchType | read-create | current | The map match type of this entry. |
| 1.3.6.1.4.1.202.20.66.1.16.4.13.1.5 | ColumndiffServClassMapElementIndexTypeList | read-only | current | The octet string containes the type of class map element indexes. Two octets which are represented in network order express one type of the class map element i… |
| 1.3.6.1.4.1.202.20.66.1.16.4.13.1.6 | ColumndiffServClassMapElementIndexList | read-only | current | The octet string containes the class map element indexes. Two octets express one index and it is represented in network order. This index list indicates the pa… |
| 1.3.6.1.4.1.202.20.66.1.16.4.13.1.7 | ColumndiffServClassMapStatus | read-create | current | This object is used to create a new row or modify or delete an existing row in this table.The status column has six defined values: The status column has six d… |
| 1.3.6.1.4.1.202.20.66.1.16.4.14 | NodediffServClassMapAttachCtl | |||
| 1.3.6.1.4.1.202.20.66.1.16.4.14.1 | ScalardiffServClassMapAttachCtlIndex | read-write | current | Index for attachment control. Specifies the class map as the target to relate with class map elements. The class map identified by a particular value of this i… |
| 1.3.6.1.4.1.202.20.66.1.16.4.14.2 | ScalardiffServClassMapAttachCtlElementIndexType | read-write | current | Element Index for attachment control. Specifies the type of class map element to relate with the class map. When type is macAce(1), the index of diffServClassM… |
| 1.3.6.1.4.1.202.20.66.1.16.4.14.3 | ScalardiffServClassMapAttachCtlElementIndex | read-write | current | Element Index for attachment control. Specifies the class map element related with the class map. The class map element uses type to indicate diffServAclEntry,… |
| 1.3.6.1.4.1.202.20.66.1.16.4.14.4 | ScalardiffServClassMapAttachCtlAction | read-write | current | Action for attachment control. When setting this object to attach(2) to begin the attaching operation, a particular class map element is attached to a particul… |
| 1.3.6.1.4.1.202.20.66.1.16.4.15 | TablediffServAclTable | not-accessible | current | Table for ACL. |
| 1.3.6.1.4.1.202.20.66.1.16.4.15.1 | RowdiffServAclEntry | not-accessible | current | Entry for ACL. |
| 1.3.6.1.4.1.202.20.66.1.16.4.15.1.1 | ColumndiffServAclIndex | not-accessible | current | An index that uniquely identifies an entry in the ACL table. |
| 1.3.6.1.4.1.202.20.66.1.16.4.15.1.2 | ColumndiffServAclName | read-create | current | The name of this entry. |
| 1.3.6.1.4.1.202.20.66.1.16.4.15.1.3 | ColumndiffServAclType | read-create | current | The type of this entry. When the value of ACL type is modified, then the ACEs in the diffServAclAceIndexList of this entry will be auto-removed, and this entry… |
| 1.3.6.1.4.1.202.20.66.1.16.4.15.1.4 | ColumndiffServAclAceIndexList | read-only | current | The octet string containes the ACE indexes. Two octets express one index and it is represented in network order. This index list indicates the particular ACEs … |
| 1.3.6.1.4.1.202.20.66.1.16.4.15.1.5 | ColumndiffServAclStatus | read-create | current | This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: - 'active', which indicate… |
| 1.3.6.1.4.1.202.20.66.1.16.4.16 | NodediffServAclAttachCtl | |||
| 1.3.6.1.4.1.202.20.66.1.16.4.16.1 | ScalardiffServAclAttachCtlIndex | read-write | current | Index for attachment control. Specifies the ACL as the target to relate with the IP ACE or MAC ACE. The ACL identified by a particular value of this index is a… |
| 1.3.6.1.4.1.202.20.66.1.16.4.16.2 | ScalardiffServAclAttachCtlAceType | read-write | current | Type for attachment control. Specifies the type of diffServAclAttachCtlAceIndex to relate with the diffServAclAttachCtlIndex. When the type is macAce(1), the i… |
| 1.3.6.1.4.1.202.20.66.1.16.4.16.3 | ScalardiffServAclAttachCtlAceIndex | read-write | current | Index for attachment control. Specifies the ACE to relate with the diffServAclAttachCtlIndex. When diffServAclAttachCtlAceType is macAce(1), the value of diffS… |
| 1.3.6.1.4.1.202.20.66.1.16.4.16.4 | ScalardiffServAclAttachCtlAction | read-write | current | Action for attachment control. When setting this object to attach(2) to begin the attaching operation, a particular ACE is attached to a particular ACL. When s… |
| 1.3.6.1.4.1.202.20.66.1.16.4.17 | TablediffServIpAceTable | not-accessible | current | Table for IP ACE. |
| 1.3.6.1.4.1.202.20.66.1.16.4.17.1 | RowdiffServIpAceEntry | not-accessible | current | Entry for IP ACE. |
| 1.3.6.1.4.1.202.20.66.1.16.4.17.1.1 | ColumndiffServIpAceIndex | not-accessible | current | An index that uniquely identifies an entry in the IP ACE table. |
| 1.3.6.1.4.1.202.20.66.1.16.4.17.1.2 | ColumndiffServIpAceType | read-create | current | The specified IP ACE type. When the type of this entry is modified, then this entry will be auto-unbound from the diffServAclEntry and the not supporting field… |
| 1.3.6.1.4.1.202.20.66.1.16.4.17.1.3 | ColumndiffServIpAceAccess | read-create | current | Indicates the action to be taken if a packet matches this ACE. |
| 1.3.6.1.4.1.202.20.66.1.16.4.17.1.4 | ColumndiffServIpAceSourceIpAddr | read-create | current | The specified source IP address. The packet's source address is AND-ed with the value of IpAceSourceIpAddrBitmask and then compared against the value of this o… |
| 1.3.6.1.4.1.202.20.66.1.16.4.17.1.5 | ColumndiffServIpAceSourceIpAddrBitmask | read-create | current | The specified source IP address mask. The packet's source address is AND-ed with the value of IpAceSourceIpAddr and then compared against the value of this obj… |
| 1.3.6.1.4.1.202.20.66.1.16.4.17.1.6 | ColumndiffServIpAceDestIpAddr | read-create | current | The specified destination IP address. The packet's destination address is AND-ed with the value of diffServIpAceDestIpAddrBitmask and then compared against the… |
| 1.3.6.1.4.1.202.20.66.1.16.4.17.1.7 | ColumndiffServIpAceDestIpAddrBitmask | read-create | current | The specified destination IP address mask. This object may not be modified if the associated diffServIpAceType object is equal to standard(1). |
| 1.3.6.1.4.1.202.20.66.1.16.4.17.1.8 | ColumndiffServIpAceProtocol | read-create | current | The protocol number field in the IP header used to indicate the higher layer protocol as specified in RFC 1700. A value of 0 matches every IP packet. The objec… |
| 1.3.6.1.4.1.202.20.66.1.16.4.17.1.9 | ColumndiffServIpAcePrec | read-create | current | Specifies the IP precedence value to match against. The value of this object is ignored whenever the value of diffServIpAcePrec object is 8. This object may no… |
| 1.3.6.1.4.1.202.20.66.1.16.4.17.1.10 | ColumndiffServIpAceTos | read-create | current | Specifies the IP ToS facility value to match against. The value of this object is ignored whenever the value of diffServIpAcePrec object is 9. This object may … |
| 1.3.6.1.4.1.202.20.66.1.16.4.17.1.11 | ColumndiffServIpAceDscp | read-create | current | Specifies the DSCP value to match against. The value of this object is ignored whenever the value of diffServIpAcePrec object is 64. This object may not be mod… |
| 1.3.6.1.4.1.202.20.66.1.16.4.17.1.12 | ColumndiffServIpAceSourcePortOp | read-create | current | Indicates how a packet's source TCP/UDP port number is to be compared. noOperator(1), which is the default value, means no comparison is to be made with the so… |
| 1.3.6.1.4.1.202.20.66.1.16.4.17.1.13 | ColumndiffServIpAceMinSourcePort | read-create | current | If the diffServIpAceSourcePortOp is range(3), this indicates the lower bound of the TCP/UDP port number value range. This object may not be modified if the ass… |
| 1.3.6.1.4.1.202.20.66.1.16.4.17.1.15 | ColumndiffServIpAceSourcePortBitmask | read-create | current | If the diffServIpAceSourcePortOp is equal(2), this indicates the bitmask of the diffServIpAceMinSourcePort. This object may not be modified if the associated d… |
| 1.3.6.1.4.1.202.20.66.1.16.4.17.1.16 | ColumndiffServIpAceDestPortOp | read-create | current | Indicates how a packet's destination TCP/UDP port number is to be compared. noOperator(1), which is the default value, means that no comparison is to be made w… |
| 1.3.6.1.4.1.202.20.66.1.16.4.17.1.17 | ColumndiffServIpAceMinDestPort | read-create | current | If the diffServIpAceDestPortOp is range(3), this indicates the lower bound of the TCP/UDP port number value range. This object may not be modified if the assoc… |
| 1.3.6.1.4.1.202.20.66.1.16.4.17.1.19 | ColumndiffServIpAceDestPortBitmask | read-create | current | If the diffServIpAceDestPortOp is equal(2), this indicates the bitmask of the diffServIpAceMinDestPort. This object may not be modified if the associated diffS… |
| 1.3.6.1.4.1.202.20.66.1.16.4.17.1.20 | ColumndiffServIpAceControlCode | read-create | current | Indicates how the control flags of TCP packets are to be compared. diffServIpAceControlCode is AND-ed with diffServIpAceControlCodeBitmask. This object may not… |
| 1.3.6.1.4.1.202.20.66.1.16.4.17.1.21 | ColumndiffServIpAceControlCodeBitmask | read-create | current | Indicates how the control flags of TCP packets are to be compared. It can be used to check multiple flags of the FIN, SYN, RST, PSH, ACK, URG by the sum of FIN… |
| 1.3.6.1.4.1.202.20.66.1.16.4.17.1.22 | ColumndiffServIpAceStatus | read-create | current | This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: The status column has six … |
| 1.3.6.1.4.1.202.20.66.1.16.4.18 | TablediffServMacAceTable | not-accessible | current | Table for MAC ACE. |
| 1.3.6.1.4.1.202.20.66.1.16.4.18.1 | RowdiffServMacAceEntry | not-accessible | current | Entry for MAC ACE. |
| 1.3.6.1.4.1.202.20.66.1.16.4.18.1.1 | ColumndiffServMacAceIndex | not-accessible | current | An index that uniquely identifies an entry in the MAC ACE table. |
| 1.3.6.1.4.1.202.20.66.1.16.4.18.1.2 | ColumndiffServMacAceAccess | read-create | current | Indicates the action to be taken if a packet matches this ACE. |
| 1.3.6.1.4.1.202.20.66.1.16.4.18.1.3 | ColumndiffServMacAcePktformat | read-create | current | Used to check the packet format of the packets. This object cannot be configured when the status of the entry, diffServMacAceStatus, is active(1). |
| 1.3.6.1.4.1.202.20.66.1.16.4.18.1.4 | ColumndiffServMacAceSourceMacAddr | read-create | current | Indicates the 48-bit source MAC address. The specified source MAC of the packet. The packet's source MAC address is AND-ed with the value of diffServMacAceSour… |
| 1.3.6.1.4.1.202.20.66.1.16.4.18.1.5 | ColumndiffServMacAceSourceMacAddrBitmask | read-create | current | The specified source MAC address mask. |
| 1.3.6.1.4.1.202.20.66.1.16.4.18.1.6 | ColumndiffServMacAceDestMacAddr | read-create | current | Indicates the 48-bit destination MAC address. The specified destination MAC of the packet. The packet's destination MAC address is AND-ed with the value of dif… |
| 1.3.6.1.4.1.202.20.66.1.16.4.18.1.7 | ColumndiffServMacAceDestMacAddrBitmask | read-create | current | The specified destination MAC address mask. |
| 1.3.6.1.4.1.202.20.66.1.16.4.18.1.8 | ColumndiffServMacAceVidOp | read-create | current | Indicates how a packet's VID is to be compared. This object cannot be configured when the status of the entry, diffServMacAceStatus, is active(1). |
| 1.3.6.1.4.1.202.20.66.1.16.4.18.1.9 | ColumndiffServMacAceMinVid | read-create | current | Indicates the lower bound of the VID value range if the diffServMacAceVidOp is range(3). |
| 1.3.6.1.4.1.202.20.66.1.16.4.18.1.10 | ColumndiffServMacAceVidBitmask | read-create | current | The bitmask of the VID if the diffServMacAceVidOp is equal(2). Default value is 0xfff. |
| 1.3.6.1.4.1.202.20.66.1.16.4.18.1.12 | ColumndiffServMacAceEtherTypeOp | read-create | current | Indicates how a packet's ether type is to be compared. |
| 1.3.6.1.4.1.202.20.66.1.16.4.18.1.13 | ColumndiffServMacAceEtherTypeBitmask | read-create | current | The bitmask of ether type if the diffServMacAceEtherTypeOp is equal(2). The default value is 'FFFF'h. |
| 1.3.6.1.4.1.202.20.66.1.16.4.18.1.14 | ColumndiffServMacAceMinEtherType | read-create | current | Indicates the lower bound of the ether type value range if the diffServMacAceEtherTypeOp is range(3). |
| 1.3.6.1.4.1.202.20.66.1.16.4.18.1.16 | ColumndiffServMacAceStatus | read-create | current | This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: The status column has six … |
| 1.3.6.1.4.1.202.20.66.1.16.4.19 | TablediffServActionTable | not-accessible | current | Table for action. |
| 1.3.6.1.4.1.202.20.66.1.16.4.19.1 | RowdiffServActionEntry | not-accessible | current | Entry for action. |
| 1.3.6.1.4.1.202.20.66.1.16.4.19.1.1 | ColumndiffServActionIndex | not-accessible | current | An index that uniquely identifies an entry in the action table. |
| 1.3.6.1.4.1.202.20.66.1.16.4.19.1.2 | ColumndiffServActionList | read-create | current | The bitmap value used to identify which action capabilities are enabled on the entry. The actionPktNewPri and actionPktNewDscp can not be enabled at the same t… |
| 1.3.6.1.4.1.202.20.66.1.16.4.19.1.3 | ColumndiffServActionPktNewPri | read-create | current | Specifies the new priority value for the packet when the action is satisfied. If the actionPktNewPri bit of the diffServActionList is not enabled, this object … |
| 1.3.6.1.4.1.202.20.66.1.16.4.19.1.5 | ColumndiffServActionPktNewDscp | read-create | current | Specifies the new DSCP value for the packet when the action is satisfied. If the actionPktNewDscp bit of the diffServActionList is not enabled, this object can… |
| 1.3.6.1.4.1.202.20.66.1.16.4.19.1.6 | ColumndiffServActionRedPktNewDscp | read-create | current | Specifies the new DSCP value for the red marking packet when the action is satisfied. If the actionRedPktNewDscp bit of the diffServActionList is not enabled, … |
| 1.3.6.1.4.1.202.20.66.1.16.4.19.1.7 | ColumndiffServActionRedDrop | read-only | current | The actionRedDrop bit of the diffServActionList is for configuring this object. If the value of this object is enabled, the red marking packet will be dropped. |
| 1.3.6.1.4.1.202.20.66.1.16.4.19.1.8 | ColumndiffServActionStatus | read-create | current | This object is used to create a new row, modify or delete an existing row in this table. The status column has six defined values: The status column has six de… |
| 1.3.6.1.4.1.202.20.66.1.16.4.20 | TablediffServMeterTable | not-accessible | current | Table for meter. |
| 1.3.6.1.4.1.202.20.66.1.16.4.20.1 | RowdiffServMeterEntry | not-accessible | current | Entry for meter. |
| 1.3.6.1.4.1.202.20.66.1.16.4.20.1.1 | ColumndiffServMeterIndex | not-accessible | current | An entry that describes a single set of token bucket parameters. |
| 1.3.6.1.4.1.202.20.66.1.16.4.20.1.2 | ColumndiffServMeterModel | read-create | current | The Metering algorithm associated with the Token Bucket parameters. The zeroDotZero indicates this is unknown. |
| 1.3.6.1.4.1.202.20.66.1.16.4.20.1.3 | ColumndiffServMeterRate | read-create | current | The token-bucket rate, in kilobits per second (kbps). |
| 1.3.6.1.4.1.202.20.66.1.16.4.20.1.4 | ColumndiffServMeterBurstSize | read-create | current | The maximum number of bytes in a single transmission burst. |
| 1.3.6.1.4.1.202.20.66.1.16.4.20.1.5 | ColumndiffServMeterInterval | read-create | current | The time interval used with the token bucket. |
| 1.3.6.1.4.1.202.20.66.1.16.4.20.1.6 | ColumndiffServMeterStatus | read-create | current | This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: The status column has six … |
| 1.3.6.1.4.1.202.20.66.1.17 | NodesecurityMgt | |||
| 1.3.6.1.4.1.202.20.66.1.17.1 | NodeprivateVlanMgt | |||
| 1.3.6.1.4.1.202.20.66.1.17.1.4 | TableprivateVlanVlanTable | not-accessible | current | A table containing private VLAN information on the VLANs which currently exist. |
| 1.3.6.1.4.1.202.20.66.1.17.1.4.1 | RowprivateVlanVlanEntry | not-accessible | current | A conceptual row containing the private VLAN information on the VLANs for a particular management domain. |
| 1.3.6.1.4.1.202.20.66.1.17.1.4.1.1 | ColumnprivateVlanVlanIndex | not-accessible | current | The VLAN ID of this private VLAN. |
| 1.3.6.1.4.1.202.20.66.1.17.1.4.1.2 | ColumnprivateVlanVlanType | read-create | current | The VLAN type as defined for Private VLAN feature. Set the value to invalid(1) to destroy an entry. Set other values to create an entry. If an index already ex… |
| 1.3.6.1.4.1.202.20.66.1.17.1.4.1.3 | ColumnprivateVlanAssoicatedPrimaryVlan | read-create | current | The VLAN ID of the associated primary VLAN used for the private VLAN feature if privateVlanVlanType has the value of isolated(3), community(4). If privateVlanV… |
| 1.3.6.1.4.1.202.20.66.1.17.1.5 | TableprivateVlanPrivatePortTable | not-accessible | current | A table containing information on the configuration of secondary VLANs on the device ports. |
| 1.3.6.1.4.1.202.20.66.1.17.1.5.1 | RowprivateVlanPrivatePortEntry | not-accessible | current | A conceptual row containing information of the configuration of secondary VLANs for each port. An entry is created by the managed system for each interface whi… |
| 1.3.6.1.4.1.202.20.66.1.17.1.5.1.1 | ColumnprivateVlanPrivatePortIfIndex | not-accessible | current | This is defined as the ifIndex. |
| 1.3.6.1.4.1.202.20.66.1.17.1.5.1.2 | ColumnprivateVlanPrivatePortSecondaryVlan | read-write | current | The VLAN ID of the secondary VLAN configured on this private port. A private port is a port that allows ingress traffic of the secondary VLAN as well as egress… |
| 1.3.6.1.4.1.202.20.66.1.17.1.6 | TableprivateVlanPromPortTable | not-accessible | current | A table containing secondary VLAN to primary VLAN remapping information on ports of the device. |
| 1.3.6.1.4.1.202.20.66.1.17.1.6.1 | RowprivateVlanPromPortEntry | not-accessible | current | A conceptual row containing secondary VLAN to primary VLAN remapping information for each port. An entry is created by the managed system for each interface wh… |
| 1.3.6.1.4.1.202.20.66.1.17.1.6.1.1 | ColumnprivateVlanPromPortIfIndex | not-accessible | current | This is defined as ifIndex. |
| 1.3.6.1.4.1.202.20.66.1.17.1.6.1.2 | ColumnprivateVlanPromPortPrimaryVlanId | read-write | current | The primary VLAN ID of the promiscous port. |
| 1.3.6.1.4.1.202.20.66.1.17.1.6.1.3 | ColumnprivateVlanPromPortSecondaryRemap | read-only | current | A string of octets containing one bit per VLAN in the management domain on this port. The first octet corresponds to VLANs with VlanIndexOrZero values of 0 thr… |
| 1.3.6.1.4.1.202.20.66.1.17.1.6.1.4 | ColumnprivateVlanPromPortSecondaryRemap2k | read-only | current | A string of octets containing one bit per VLAN for VLANs with VlanIndexOrZero values of 1024 through 2047 in the management domain on this port. The first octe… |
| 1.3.6.1.4.1.202.20.66.1.17.1.6.1.5 | ColumnprivateVlanPromPortSecondaryRemap3k | read-only | current | A string of octets containing one bit per VLAN for VLANs with VlanIndexOrZero values of 2048 through 3071 in the management domain on this port. The first octe… |
| 1.3.6.1.4.1.202.20.66.1.17.1.6.1.6 | ColumnprivateVlanPromPortSecondaryRemap4k | read-only | current | A string of octets containing one bit per VLAN for VLANs with VlanIndexOrZero values of 3072 through 4095 in the management domain on this port. The first octe… |
| 1.3.6.1.4.1.202.20.66.1.17.2 | NodeportSecurityMgt | |||
| 1.3.6.1.4.1.202.20.66.1.17.2.1 | TableportSecPortTable | not-accessible | current | The port security(MAC binding) Table. |
| 1.3.6.1.4.1.202.20.66.1.17.2.1.1 | RowportSecPortEntry | not-accessible | current | The entry of portSecPortTable. |
| 1.3.6.1.4.1.202.20.66.1.17.2.1.1.1 | ColumnportSecPortIndex | not-accessible | current | The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface… |
| 1.3.6.1.4.1.202.20.66.1.17.2.1.1.2 | ColumnportSecPortStatus | read-write | current | Set enabled(1) to enable port security and set disabled(2) to disable port security. |
| 1.3.6.1.4.1.202.20.66.1.17.2.1.1.3 | ColumnportSecAction | read-write | current | The corresponding actions that will take place when a port is under intrusion, when this variable is set to none(1), no action will be performed, when this var… |
| 1.3.6.1.4.1.202.20.66.1.17.2.1.1.4 | ColumnportSecMaxMacCount | read-write | current | The maximun number of MAC addresses that will be learned and locked. When we change the value of this variable, if the portSecPortStatus is enabled, we will di… |
| 1.3.6.1.4.1.202.20.66.1.17.4 | NoderadiusMgt | |||
| 1.3.6.1.4.1.202.20.66.1.17.4.2 | ScalarradiusServerPortNumber | read-write | current | IP port number of RADIUS server. |
| 1.3.6.1.4.1.202.20.66.1.17.4.3 | ScalarradiusServerKey | read-write | current | Key for RADIUS. This variable can only be set. When this variable is read, it always returns a zero-length string. |
| 1.3.6.1.4.1.202.20.66.1.17.4.4 | ScalarradiusServerRetransmit | read-write | current | Maximum number of retransmissions for RADIUS. |
| 1.3.6.1.4.1.202.20.66.1.17.4.5 | ScalarradiusServerTimeout | read-write | current | Timeout for RADIUS. |
| 1.3.6.1.4.1.202.20.66.1.17.4.7 | TableradiusMultipleServerTable | not-accessible | current | The table for multiple RADIUS server. |
| 1.3.6.1.4.1.202.20.66.1.17.4.7.1 | RowradiusMultipleServerEntry | not-accessible | current | The conceptual row for radiusMultipleServerTable. |
| 1.3.6.1.4.1.202.20.66.1.17.4.7.1.1 | ColumnradiusMultipleServerIndex | not-accessible | current | The RADIUS multiple server index. |
| 1.3.6.1.4.1.202.20.66.1.17.4.7.1.2 | ColumnradiusMultipleServerAddress | read-create | current | IP address of a multiple RADIUS server. |
| 1.3.6.1.4.1.202.20.66.1.17.4.7.1.3 | ColumnradiusMultipleServerPortNumber | read-create | current | IP port number of a multiple RADIUS server. |
| 1.3.6.1.4.1.202.20.66.1.17.4.7.1.4 | ColumnradiusMultipleServerKey | read-create | current | Key for RADIUS. This variable can only be set. When this variable is read, it always returns a zero-length string. |
| 1.3.6.1.4.1.202.20.66.1.17.4.7.1.5 | ColumnradiusMultipleServerRetransmit | read-create | current | Maximum number of retransmissions for RADIUS. |
| 1.3.6.1.4.1.202.20.66.1.17.4.7.1.6 | ColumnradiusMultipleServerTimeout | read-create | current | Timeout for RADIUS. |
| 1.3.6.1.4.1.202.20.66.1.17.4.7.1.8 | ColumnradiusMultipleServerStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.202.20.66.1.17.5 | NodetacacsMgt | |||
| 1.3.6.1.4.1.202.20.66.1.17.5.1 | ScalartacacsServerAddress | read-write | current | IP address of TACACS server. |
| 1.3.6.1.4.1.202.20.66.1.17.5.2 | ScalartacacsServerPortNumber | read-write | current | IP port number of TACACS server. |
| 1.3.6.1.4.1.202.20.66.1.17.5.3 | ScalartacacsServerKey | read-write | current | The encryption key used to authenticate logon access for the client using TACAS. Do not use blank spaces in the string. This variable can only be set. When thi… |
| 1.3.6.1.4.1.202.20.66.1.17.6 | NodesshMgt | |||
| 1.3.6.1.4.1.202.20.66.1.17.6.1 | ScalarsshServerStatus | read-write | current | The status of Secure Shell Server. Set this value to enabled(1) to enable SSH server, set this value to disabled(2) to disable the SSH server. |
| 1.3.6.1.4.1.202.20.66.1.17.6.2 | ScalarsshServerMajorVersion | read-only | current | The major version of the SSH Server. |
| 1.3.6.1.4.1.202.20.66.1.17.6.3 | ScalarsshServerMinorVersion | read-only | current | The minor version of the SSH Server. |
| 1.3.6.1.4.1.202.20.66.1.17.6.4 | ScalarsshTimeout | read-write | current | The time interval that the router waits for the SSH client to respond. The range is 1-120. |
| 1.3.6.1.4.1.202.20.66.1.17.6.5 | ScalarsshAuthRetries | read-write | current | The number of attempts after which the interface is reset. The range is 1-5. |
| 1.3.6.1.4.1.202.20.66.1.17.6.6 | TablesshConnInfoTable | not-accessible | current | The table for Secure Shell Connection. |
| 1.3.6.1.4.1.202.20.66.1.17.6.6.1 | RowsshConnInfoEntry | not-accessible | current | The conceptual row for sshConnInfoTable. |
| 1.3.6.1.4.1.202.20.66.1.17.6.6.1.1 | ColumnsshConnID | not-accessible | current | The connection ID of the Secure Shell Connection. |
| 1.3.6.1.4.1.202.20.66.1.17.6.6.1.2 | ColumnsshConnMajorVersion | read-only | current | The SSH major version. |
| 1.3.6.1.4.1.202.20.66.1.17.6.6.1.3 | ColumnsshConnMinorVersion | read-only | current | The SSH minor version. |
| 1.3.6.1.4.1.202.20.66.1.17.6.6.1.5 | ColumnsshConnStatus | read-only | current | The SSH connection State. negotiationStart(1) means the SSH is in its negotiation start state, authenticationStart(2) means the SSH is in authentication start … |
| 1.3.6.1.4.1.202.20.66.1.17.6.6.1.6 | ColumnsshConnUserName | read-only | current | The user name of the connection. |
| 1.3.6.1.4.1.202.20.66.1.17.6.6.1.7 | ColumnsshDisconnect | read-write | current | Set the variable to disconnect the connection, noDisconnect(1) will always be obtained when reading this variable. |
| 1.3.6.1.4.1.202.20.66.1.17.6.6.1.8 | ColumnsshConnEncryptionTypeStr | read-only | current | The encryption type of the SSH. |
| 1.3.6.1.4.1.202.20.66.1.17.6.7 | ScalarsshKeySize | read-write | current | The SSH server key size. |
| 1.3.6.1.4.1.202.20.66.1.17.6.8 | ScalarsshRsaHostKey1 | read-only | current | The RSA host key segment 1. |
| 1.3.6.1.4.1.202.20.66.1.17.6.9 | ScalarsshRsaHostKey2 | read-only | current | The RSA host key segment 2. |
| 1.3.6.1.4.1.202.20.66.1.17.6.10 | ScalarsshRsaHostKey3 | read-only | current | The RSA host key segment 3. |
| 1.3.6.1.4.1.202.20.66.1.17.6.11 | ScalarsshRsaHostKey4 | read-only | current | The RSA host key segment 4. |
| 1.3.6.1.4.1.202.20.66.1.17.6.12 | ScalarsshRsaHostKey5 | read-only | current | The RSA host key segment 5. |
| 1.3.6.1.4.1.202.20.66.1.17.6.13 | ScalarsshRsaHostKey6 | read-only | current | The RSA host key segment 6. |
| 1.3.6.1.4.1.202.20.66.1.17.6.14 | ScalarsshRsaHostKey7 | read-only | current | The RSA host key segment 7. |
| 1.3.6.1.4.1.202.20.66.1.17.6.15 | ScalarsshRsaHostKey8 | read-only | current | The RSA host key segment 8. |
| 1.3.6.1.4.1.202.20.66.1.17.6.16 | ScalarsshDsaHostKey1 | read-only | current | The DSA host key segment 1. |
| 1.3.6.1.4.1.202.20.66.1.17.6.17 | ScalarsshDsaHostKey2 | read-only | current | The DSA host key segment 2. |
| 1.3.6.1.4.1.202.20.66.1.17.6.18 | ScalarsshDsaHostKey3 | read-only | current | The DSA host key segment 3. |
| 1.3.6.1.4.1.202.20.66.1.17.6.19 | ScalarsshDsaHostKey4 | read-only | current | The DSA host key segment 4. |
| 1.3.6.1.4.1.202.20.66.1.17.6.20 | ScalarsshDsaHostKey5 | read-only | current | The DSA host key segment 5. |
| 1.3.6.1.4.1.202.20.66.1.17.6.21 | ScalarsshDsaHostKey6 | read-only | current | The DSA host key segment 6. |
| 1.3.6.1.4.1.202.20.66.1.17.6.22 | ScalarsshDsaHostKey7 | read-only | current | The DSA host key segment 7. |
| 1.3.6.1.4.1.202.20.66.1.17.6.23 | ScalarsshDsaHostKey8 | read-only | current | The DSA host key segment 8. |
| 1.3.6.1.4.1.202.20.66.1.17.6.24 | ScalarsshHostKeyGenAction | read-write | current | This variable is for host key generating. For the set behavior: Set it to genRsaKey(2) to generate the RSA host key, and to genDsaKey(3) to generate the DSA ho… |
| 1.3.6.1.4.1.202.20.66.1.17.6.25 | ScalarsshHostKeyGenStatus | read-only | current | The result of the last KeyGen status. if no key gen action has been performed. you will get unknown(1) status. |
| 1.3.6.1.4.1.202.20.66.1.17.6.26 | ScalarsshHostKeySaveAction | read-write | current | To save host key from memory to flash. For the set behavior: Set it to save(2) to perform the save operation. For the get behavior: You will get save(1) when t… |
| 1.3.6.1.4.1.202.20.66.1.17.6.27 | ScalarsshHostKeySaveStatus | read-only | current | The result of the last savekey status. If no save action has been performed, you will get unknown(1) status. |
| 1.3.6.1.4.1.202.20.66.1.17.6.28 | ScalarsshHostKeyDelAction | read-write | current | To delete the host key. For the set behavior: Set it to delRsaKey(2) to delete the RSA host key, to delDsaKey(3) to delete the DSA host key, or to delBothKeys(… |
| 1.3.6.1.4.1.202.20.66.1.17.6.29 | TablesshUserTable | not-accessible | current | The conceptual table of all of sshUserEntry. |
| 1.3.6.1.4.1.202.20.66.1.17.6.29.1 | RowsshUserEntry | not-accessible | current | The conceptual row for sshUserTable. |
| 1.3.6.1.4.1.202.20.66.1.17.6.29.1.1 | ColumnsshUserName | not-accessible | current | User Name. |
| 1.3.6.1.4.1.202.20.66.1.17.6.29.1.2 | ColumnsshUserRsaKey1 | read-only | current | The RSA user key segment 1. |
| 1.3.6.1.4.1.202.20.66.1.17.6.29.1.3 | ColumnsshUserRsaKey2 | read-only | current | The RSA user key segment 2. |
| 1.3.6.1.4.1.202.20.66.1.17.6.29.1.4 | ColumnsshUserRsaKey3 | read-only | current | The RSA user key segment 3. |
| 1.3.6.1.4.1.202.20.66.1.17.6.29.1.5 | ColumnsshUserRsaKey4 | read-only | current | The RSA user key segment 4. |
| 1.3.6.1.4.1.202.20.66.1.17.6.29.1.6 | ColumnsshUserRsaKey5 | read-only | current | The RSA user key segment 5. |
| 1.3.6.1.4.1.202.20.66.1.17.6.29.1.7 | ColumnsshUserRsaKey6 | read-only | current | The RSA user key segment 6. |
| 1.3.6.1.4.1.202.20.66.1.17.6.29.1.8 | ColumnsshUserRsaKey7 | read-only | current | The RSA user key segment 7. |
| 1.3.6.1.4.1.202.20.66.1.17.6.29.1.9 | ColumnsshUserRsaKey8 | read-only | current | The RSA user key segment 8. |
| 1.3.6.1.4.1.202.20.66.1.17.6.29.1.10 | ColumnsshUserDsaKey1 | read-only | current | The DSA user key segment 1. |
| 1.3.6.1.4.1.202.20.66.1.17.6.29.1.11 | ColumnsshUserDsaKey2 | read-only | current | The DSA user key segment 2. |
| 1.3.6.1.4.1.202.20.66.1.17.6.29.1.12 | ColumnsshUserDsaKey3 | read-only | current | The DSA user key segment 3. |
| 1.3.6.1.4.1.202.20.66.1.17.6.29.1.13 | ColumnsshUserDsaKey4 | read-only | current | The DSA user key segment 4. |
| 1.3.6.1.4.1.202.20.66.1.17.6.29.1.14 | ColumnsshUserDsaKey5 | read-only | current | The DSA user key segment 5. |
| 1.3.6.1.4.1.202.20.66.1.17.6.29.1.15 | ColumnsshUserDsaKey6 | read-only | current | The DSA user key segment 6. |
| 1.3.6.1.4.1.202.20.66.1.17.6.29.1.16 | ColumnsshUserDsaKey7 | read-only | current | The DSA user key segment 7. |
| 1.3.6.1.4.1.202.20.66.1.17.6.29.1.17 | ColumnsshUserDsaKey8 | read-only | current | The DSA user key segment 8. |
| 1.3.6.1.4.1.202.20.66.1.17.6.29.1.18 | ColumnsshUserKeyDelAction | read-write | current | To delete the user key. For the set behavior: Set it to delRsaKey(2) to delete the RSA user key, to delDsaKey(3) to delete the DSA user key, or to delBothKeys(… |
| 1.3.6.1.4.1.202.20.66.1.17.6.30 | ScalarsshRsaHostKeySHA1FingerPrint | read-only | current | The SHA1 finger print of the RSA host key. |
| 1.3.6.1.4.1.202.20.66.1.17.6.31 | ScalarsshRsaHostKeyMD5FingerPrint | read-only | current | The MD5 finger print of RSA host key. |
| 1.3.6.1.4.1.202.20.66.1.17.6.32 | ScalarsshDsaHostKeySHA1FingerPrint | read-only | current | The SHA1 finger print of the DSA host key. |
| 1.3.6.1.4.1.202.20.66.1.17.6.33 | ScalarsshDsaHostKeyMD5FingerPrint | read-only | current | The MD5 finger print of the DSA host key. |
| 1.3.6.1.4.1.202.20.66.1.17.7 | NodeaclMgt | |||
| 1.3.6.1.4.1.202.20.66.1.17.9 | NodeipFilterMgt | |||
| 1.3.6.1.4.1.202.20.66.1.17.9.1 | TableipFilterSnmpTable | not-accessible | current | A list of IP address entries. |
| 1.3.6.1.4.1.202.20.66.1.17.9.1.1 | RowipFilterSnmpEntry | not-accessible | current | This entry includes an IP address range which the system will allow to connect to this device through SNMP. |
| 1.3.6.1.4.1.202.20.66.1.17.9.1.1.1 | ColumnipFilterSnmpStartAddress | not-accessible | current | The start IP address. |
| 1.3.6.1.4.1.202.20.66.1.17.9.1.1.2 | ColumnipFilterSnmpEndAddress | read-create | current | The end IP address. |
| 1.3.6.1.4.1.202.20.66.1.17.9.1.1.3 | ColumnipFilterSnmpStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.202.20.66.1.17.9.2 | TableipFilterHTTPTable | not-accessible | current | A list of IP address entries. |
| 1.3.6.1.4.1.202.20.66.1.17.9.2.1 | RowipFilterHTTPEntry | not-accessible | current | This entry includes an IP address range which the system will allow to connect to this device through SNMP. |
| 1.3.6.1.4.1.202.20.66.1.17.9.2.1.1 | ColumnipFilterHTTPStartAddress | not-accessible | current | The start IP address. |
| 1.3.6.1.4.1.202.20.66.1.17.9.2.1.2 | ColumnipFilterHTTPEndAddress | read-create | current | The end IP address. |
| 1.3.6.1.4.1.202.20.66.1.17.9.2.1.3 | ColumnipFilterHTTPStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.202.20.66.1.17.9.3 | TableipFilterTelnetTable | not-accessible | current | A list of IP address entries. |
| 1.3.6.1.4.1.202.20.66.1.17.9.3.1 | RowipFilterTelnetEntry | not-accessible | current | This entry includes an IP address range which the system will allow them to connect to this device through SNMP. |
| 1.3.6.1.4.1.202.20.66.1.17.9.3.1.1 | ColumnipFilterTelnetStartAddress | not-accessible | current | The start IP address. |
| 1.3.6.1.4.1.202.20.66.1.17.9.3.1.2 | ColumnipFilterTelnetEndAddress | read-create | current | The end IP address. |
| 1.3.6.1.4.1.202.20.66.1.17.9.3.1.3 | ColumnipFilterTelnetStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.202.20.66.1.19 | NodesysLogMgt | |||
| 1.3.6.1.4.1.202.20.66.1.19.1 | ScalarsysLogStatus | read-write | current | Whether the system log is enabled. |
| 1.3.6.1.4.1.202.20.66.1.19.2 | ScalarsysLogHistoryFlashLevel | read-write | current | Severity level for logging to flash. |
| 1.3.6.1.4.1.202.20.66.1.19.3 | ScalarsysLogHistoryRamLevel | read-write | current | Severity level for logging to RAM. |
| 1.3.6.1.4.1.202.20.66.1.19.6 | NoderemoteLogMgt | |||
| 1.3.6.1.4.1.202.20.66.1.19.6.1 | ScalarremoteLogStatus | read-write | current | Whether the remote log system is enabled. |
| 1.3.6.1.4.1.202.20.66.1.19.6.2 | ScalarremoteLogLevel | read-write | current | Severity level for remote log. |
| 1.3.6.1.4.1.202.20.66.1.19.6.3 | ScalarremoteLogFacilityType | read-write | current | The facility type for remote log. |
| 1.3.6.1.4.1.202.20.66.1.19.6.4 | TableremoteLogServerTable | not-accessible | current | A Table for storing the remote log Server list. |
| 1.3.6.1.4.1.202.20.66.1.19.6.4.1 | RowremoteLogServerEntry | not-accessible | current | A conceptually row for remoteLogServerTable. |
| 1.3.6.1.4.1.202.20.66.1.19.6.4.1.1 | ColumnremoteLogServerIp | not-accessible | current | The IP address of the remote log Server. |
| 1.3.6.1.4.1.202.20.66.1.19.6.4.1.2 | ColumnremoteLogServerStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.202.20.66.1.19.7 | NodesmtpMgt | |||
| 1.3.6.1.4.1.202.20.66.1.19.7.1 | ScalarsmtpStatus | read-write | current | Set enabled(1) to enable the SMTP, set disabled(2) to disable the SMTP. |
| 1.3.6.1.4.1.202.20.66.1.19.7.2 | ScalarsmtpSeverityLevel | read-write | current | Specify the SMTP minimum severity level to send the event message. |
| 1.3.6.1.4.1.202.20.66.1.19.7.3 | ScalarsmtpSourceEMail | read-write | current | SMTP source email address, the sender's mail address that appears in the 'From' field of the mail. |
| 1.3.6.1.4.1.202.20.66.1.19.7.4 | TablesmtpServerIpTable | not-accessible | current | The SMTP server IP table. The maximum servers to be added is 3. |
| 1.3.6.1.4.1.202.20.66.1.19.7.4.1 | RowsmtpServerIpEntry | not-accessible | current | A conceptual row of the smtpServerIpTable. |
| 1.3.6.1.4.1.202.20.66.1.19.7.4.1.1 | ColumnsmtpServerIp | accessible-for-notify | current | SMTP mail server's IP address. |
| 1.3.6.1.4.1.202.20.66.1.19.7.4.1.2 | ColumnsmtpServerIpStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.202.20.66.1.19.7.5 | TablesmtpDestEMailTable | not-accessible | current | The table of the destination e-mail address. The maximum numbers of destination email address to be added is 5. |
| 1.3.6.1.4.1.202.20.66.1.19.7.5.1 | RowsmtpDestEMailEntry | not-accessible | current | A conceptual row of the smtpDestEMailTable. |
| 1.3.6.1.4.1.202.20.66.1.19.7.5.1.1 | ColumnsmtpDestEMail | not-accessible | current | SMTP destination e-mail address. |
| 1.3.6.1.4.1.202.20.66.1.19.7.5.1.2 | ColumnsmtpDestEMailStatus | read-create | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.202.20.66.1.20 | NodelineMgt | |||
| 1.3.6.1.4.1.202.20.66.1.20.1 | NodeconsoleMgt | |||
| 1.3.6.1.4.1.202.20.66.1.20.1.1 | ScalarconsoleDataBits | read-write | current | Number of data bits. |
| 1.3.6.1.4.1.202.20.66.1.20.1.2 | ScalarconsoleParity | read-write | current | Defines the generation of a parity bit. |
| 1.3.6.1.4.1.202.20.66.1.20.1.4 | ScalarconsoleStopBits | read-write | current | The console stop bits, valid values are stopbits1(1) or stopbits2(2) |
| 1.3.6.1.4.1.202.20.66.1.20.1.5 | ScalarconsoleExecTimeout | read-write | current | In a serial console, use the consoleExecTimeout variable to set the interval that the EXEC command interpreter waits until user input is detected; set the valu… |
| 1.3.6.1.4.1.202.20.66.1.20.1.6 | ScalarconsolePasswordThreshold | read-write | current | The number of failed console logon attempts that may be made before the system will not accept a further attempt in the time specified by consoleSilentTime. A … |
| 1.3.6.1.4.1.202.20.66.1.20.1.7 | ScalarconsoleSilentTime | read-write | current | The length of time that the management console is inaccessible after the number of failed logon attempts has reached consolePasswordThreshold. A value of 0 dis… |
| 1.3.6.1.4.1.202.20.66.1.20.1.8 | ScalarconsoleAdminBaudRate | read-write | current | Baud rate. Valid values are 2400, 4800, 9600, 19200, 38400, 57600, 115200. Setting this variable to 0 means autobaud. Please read the actual baud rate in the c… |
| 1.3.6.1.4.1.202.20.66.1.20.1.9 | ScalarconsoleOperBaudRate | read-only | current | The baud rate currently in use. |
| 1.3.6.1.4.1.202.20.66.1.20.1.10 | ScalarconsoleLoginResponseTimeout | read-write | current | Console login response timeout setting. Valid range is 0 to 300. Setting to 0 means disabled. |
| 1.3.6.1.4.1.202.20.66.1.20.2 | NodetelnetMgt | |||
| 1.3.6.1.4.1.202.20.66.1.20.2.1 | ScalartelnetExecTimeout | read-write | current | Specifies the interval that the system waits for user input before terminating the current telnet session. |
| 1.3.6.1.4.1.202.20.66.1.20.2.2 | ScalartelnetPasswordThreshold | read-write | current | The number of failed telnet logon attempts that may be made before the system will not accept a further attempt to logon with telnet. |
| 1.3.6.1.4.1.202.20.66.1.20.2.3 | ScalartelnetLoginResponseTimeout | read-write | current | Telnet login response timeout setting. Valid range is 1 to 300. This timout setting cannot be disbled. |
| 1.3.6.1.4.1.202.20.66.1.20.2.4 | ScalartelnetStatus | read-write | current | To enable or disable the telnet function. Any new telnet request will be rejected and all current telnet sessions will be terminated if this status is set to d… |
| 1.3.6.1.4.1.202.20.66.1.20.2.5 | ScalartelnetPortNumber | read-write | current | The telnet session port number. |
| 1.3.6.1.4.1.202.20.66.1.23 | NodesysTimeMgt | |||
| 1.3.6.1.4.1.202.20.66.1.23.1 | NodesntpMgt | |||
| 1.3.6.1.4.1.202.20.66.1.23.1.1 | ScalarsntpStatus | read-write | current | Set enabled(1) to enable the SNTP, set disabled(2) to disable the SNTP. |
| 1.3.6.1.4.1.202.20.66.1.23.1.2 | ScalarsntpServiceMode | read-write | current | Service mode. |
| 1.3.6.1.4.1.202.20.66.1.23.1.3 | ScalarsntpPollInterval | read-write | current | Polling interval. |
| 1.3.6.1.4.1.202.20.66.1.23.1.4 | TablesntpServerTable | not-accessible | current | Table for SNTP servers |
| 1.3.6.1.4.1.202.20.66.1.23.1.4.1 | RowsntpServerEntry | not-accessible | current | Entry for SNTP servers. |
| 1.3.6.1.4.1.202.20.66.1.23.1.4.1.1 | ColumnsntpServerIndex | not-accessible | current | The index of a server. This table has fixed size. |
| 1.3.6.1.4.1.202.20.66.1.23.1.4.1.2 | ColumnsntpServerIpAddress | read-write | current | The IP address of a server. Valid IP addresses must occupy contiguous indexes. All IP addresses after the last valid index are 0. |
| 1.3.6.1.4.1.202.20.66.1.23.2 | ScalarsysCurrentTime | read-write | current | This is a text string in the following form, based on Unix: 'Mmm _d hh:mm:ss yyyy'. 'Mmm' are the first three letters of the English name of the month. '_d' is… |
| 1.3.6.1.4.1.202.20.66.1.23.3 | ScalarsysTimeZone | read-write | current | This is a text string in the following form: '[s]hh:mm'. '[s]' is a plus-or-minus sign. For UTC, this is omitted. For a positive offset, this is '+'. For a neg… |
| 1.3.6.1.4.1.202.20.66.1.23.4 | ScalarsysTimeZoneName | read-write | current | The name of the time zone. |
| 1.3.6.1.4.1.202.20.66.1.24 | NodefileMgt | |||
| 1.3.6.1.4.1.202.20.66.1.24.1 | NodefileCopyMgt | |||
| 1.3.6.1.4.1.202.20.66.1.24.1.1 | ScalarfileCopySrcOperType | read-write | current | The Copy Operation that we want to perform on the fileCopyDestOperType, this operation is similar to the CLI command 'copy fileCopySrcOperType fileCopyDestOper… |
| 1.3.6.1.4.1.202.20.66.1.24.1.2 | ScalarfileCopySrcFileName | read-write | current | The source file name for fileCopyMgt when a copy operation is next requested via this MIB. This value is set to a zero length string when no file name has been… |
| 1.3.6.1.4.1.202.20.66.1.24.1.3 | ScalarfileCopyDestOperType | read-write | current | The Copy Operation that we want to perform on fileCopySrcOperType, this operation is similar to the CLI command 'copy fileCopySrcOperType fileCopyDestOperType'… |
| 1.3.6.1.4.1.202.20.66.1.24.1.4 | ScalarfileCopyDestFileName | read-write | current | The destination file name for fileCopyMgt when a copy operation is next requested via this MIB. This value is set to a zero length string when no file name has… |
| 1.3.6.1.4.1.202.20.66.1.24.1.5 | ScalarfileCopyFileType | read-write | current | Type of file to copy in fileCopyMgt. If the fileCopySrcOperType or fileCopyDestOperType is either runningCfg(2) or startupCfg(3), this variable can be ignored.… |
| 1.3.6.1.4.1.202.20.66.1.24.1.6 | ScalarfileCopyTftpServer | read-write | current | The IP address of the TFTP server for transfer when a download is next requested via this MIB. This value is set to '0.0.0.0' when no IP address has been speci… |
| 1.3.6.1.4.1.202.20.66.1.24.1.7 | ScalarfileCopyUnitId | read-write | current | Specifies the switch unit for stackable devices. When performing the 'copy unit file' or 'copy file unit' action, if neither fileCopySrcOperType nor fileCopyDe… |
| 1.3.6.1.4.1.202.20.66.1.24.1.8 | ScalarfileCopyAction | read-write | current | Setting this object to copy(2) to begin the copy Operation. |
| 1.3.6.1.4.1.202.20.66.1.24.1.9 | ScalarfileCopyStatus | read-only | current | The status of the last copy procedure, if any. This object will have a value of fileCopyUnknown(18) if no copy operation has been performed. |
| 1.3.6.1.4.1.202.20.66.1.24.2 | NodefileInfoMgt | |||
| 1.3.6.1.4.1.202.20.66.1.24.2.1 | TablefileInfoTable | not-accessible | current | This table contain the information of the file system; we can also perform the delete, set startup file operation. |
| 1.3.6.1.4.1.202.20.66.1.24.2.1.1 | RowfileInfoEntry | not-accessible | current | A conceptually row for fileInfoTable. |
| 1.3.6.1.4.1.202.20.66.1.24.2.1.1.1 | ColumnfileInfoUnitID | not-accessible | current | The switch unit in a stacking system, in a non-stacking system, this value is always 1. |
| 1.3.6.1.4.1.202.20.66.1.24.2.1.1.2 | ColumnfileInfoFileName | not-accessible | current | The file Name of the file System in the device. |
| 1.3.6.1.4.1.202.20.66.1.24.2.1.1.3 | ColumnfileInfoFileType | read-only | current | The file type of the file System in the device. |
| 1.3.6.1.4.1.202.20.66.1.24.2.1.1.4 | ColumnfileInfoIsStartUp | read-write | current | This flag indicate whether this file is a startup file. Set this object to true(1) to indicate that this is a startup file. Setting this object to false(2) is … |
| 1.3.6.1.4.1.202.20.66.1.24.2.1.1.5 | ColumnfileInfoFileSize | read-only | current | The sizes( in bytes) of the file. |
| 1.3.6.1.4.1.202.20.66.1.24.2.1.1.6 | ColumnfileInfoCreationTime | read-only | current | The creation time of the file, This is a text string in the following form, based on Unix: 'Mmm _d hh:mm:ss yyyy'. 'Mmm' are the first three letters of the Eng… |
| 1.3.6.1.4.1.202.20.66.1.24.2.1.1.7 | ColumnfileInfoDelete | read-write | current | Write this object to delete(2) to delete a file, when read, this always return noDelete(1). |
| 1.3.6.1.4.1.202.20.66.1.24.3 | TablefileAutoDownloadResultTable | not-accessible | current | This table contains file auto download result information. |
| 1.3.6.1.4.1.202.20.66.1.24.3.1 | RowfileAutoDownloadResultEntry | not-accessible | current | A conceptual row for fileAutoDownloadResultTable. |
| 1.3.6.1.4.1.202.20.66.1.24.3.1.1 | ColumnfileAutoDownloadResultUnitID | not-accessible | current | The switch unit in a stacking system, in a non-stacking system, this value is always 1. |
| 1.3.6.1.4.1.202.20.66.1.24.3.1.2 | ColumnfileAutoDownloadResultAction | read-only | current | The status of the auto download action. value copying(2) will be obtained if the auto download action is currently processing, or value notCopying(1) will be o… |
| 1.3.6.1.4.1.202.20.66.1.24.3.1.3 | ColumnfileAutoDownloadResultStatus | read-only | current | The last auto download result status. value fileCopyUnknown(18) will be obtained if no download action has been performed before. |
| 1.3.6.1.4.1.202.20.66.1.44 | NodemvrMgt | |||
| 1.3.6.1.4.1.202.20.66.1.44.1 | ScalarmvrStatus | read-write | current | Parameter to enable or disable MVR(Multicast VLAN Registration) on the device. NOTE: IGMP Snooping must be enabled first before enabling MVR and MVR will be di… |
| 1.3.6.1.4.1.202.20.66.1.44.2 | ScalarmvrVlanId | read-write | current | To set VLAN for MVR.The VLAN identified by a particular value of this index is the same VLAN as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-… |
| 1.3.6.1.4.1.202.20.66.1.44.3 | ScalarmvrMaxGroups | read-only | current | The maximum number of MVR groups. |
| 1.3.6.1.4.1.202.20.66.1.44.4 | ScalarmvrCurrentGroups | read-only | current | The current number of MVR groups. |
| 1.3.6.1.4.1.202.20.66.1.44.5 | NodemvrGroupsCtl | |||
| 1.3.6.1.4.1.202.20.66.1.44.5.1 | ScalarmvrGroupsCtlId | read-write | current | The start of a contiguous range of MVR group addresses. |
| 1.3.6.1.4.1.202.20.66.1.44.5.2 | ScalarmvrGroupsCtlCount | read-write | current | The range count for configuring MVR group addresses. |
| 1.3.6.1.4.1.202.20.66.1.44.5.3 | ScalarmvrGroupsCtlAction | read-write | current | Sets the configure action for a contiguous range of MVR group addresses. The start addresses is the current value of mvrGroupsCtlId and the range count is the … |
| 1.3.6.1.4.1.202.20.66.1.44.6 | TablemvrGroupTable | not-accessible | current | The table for configuring the MVR group. |
| 1.3.6.1.4.1.202.20.66.1.44.6.1 | RowmvrGroupEntry | not-accessible | current | The entry for configuring the MVR group. |
| 1.3.6.1.4.1.202.20.66.1.44.6.1.1 | ColumnmvrGroupId | not-accessible | current | The multicast address of the MVR group. |
| 1.3.6.1.4.1.202.20.66.1.44.6.1.2 | ColumnmvrGroutActive | read-only | current | To indicate if the group has a member or not. If there are no members, the status is inactive(2); otherwise the status is active(1). |
| 1.3.6.1.4.1.202.20.66.1.44.6.1.3 | ColumnmvrGroupStatus | read-write | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.202.20.66.1.44.7 | TablemvrGroupStaticTable | not-accessible | current | The table for configuring the static members of the MVR group. |
| 1.3.6.1.4.1.202.20.66.1.44.7.1 | RowmvrGroupStaticEntry | not-accessible | current | The entry for configuring the static members of the MVR group. |
| 1.3.6.1.4.1.202.20.66.1.44.7.1.1 | ColumnmvrGroupStaticAddress | not-accessible | current | The multicast address of the MVR group. |
| 1.3.6.1.4.1.202.20.66.1.44.7.1.2 | ColumnmvrGroupStaticPorts | read-write | current | The set of ports configured by management in this entry. Ports entered in this list will be the static members of this MVR group. |
| 1.3.6.1.4.1.202.20.66.1.44.7.1.3 | ColumnmvrGroupStaticStatus | read-write | current | Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry. |
| 1.3.6.1.4.1.202.20.66.1.44.8 | TablemvrGroupCurrentTable | not-accessible | current | The table for the current members of the MVR group. |
| 1.3.6.1.4.1.202.20.66.1.44.8.1 | RowmvrGroupCurrentEntry | not-accessible | current | The entry for the current members of the MVR group. |
| 1.3.6.1.4.1.202.20.66.1.44.8.1.1 | ColumnmvrGroupCurrentAddress | not-accessible | current | The multicast address of the MVR group. |
| 1.3.6.1.4.1.202.20.66.1.44.8.1.2 | ColumnmvrGroupCurrentPorts | read-only | current | The complete set of ports currently associated with this MVR group. |
| 1.3.6.1.4.1.202.20.66.1.44.9 | TablemvrPortTable | not-accessible | current | The table for configuring the MVR port. |
| 1.3.6.1.4.1.202.20.66.1.44.9.1 | RowmvrPortEntry | not-accessible | current | The entry for configuring the MVR port. |
| 1.3.6.1.4.1.202.20.66.1.44.9.1.1 | ColumnmvrIfIndex | not-accessible | current | The port interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIn… |
| 1.3.6.1.4.1.202.20.66.1.44.9.1.2 | ColumnmvrPortType | read-write | current | For configuring the MVR port type. To disable the MVR port type, use the none(0). |
| 1.3.6.1.4.1.202.20.66.1.44.9.1.3 | ColumnmvrPortImmediateLeave | read-write | current | To enable immediate leave on MVR port. |
| 1.3.6.1.4.1.202.20.66.1.44.9.1.4 | ColumnmvrPortActive | read-only | current | To indicate if the port is associated with the MVR group. If the port is the MVR receiver port or the MVR source port in MVR vlan, the status is active(1); oth… |
| 1.3.6.1.4.1.202.20.66.1.44.10 | ScalarmvrRunningStatus | read-only | current | Describes the running status of MVR (Multicast VLAN Registration) to the switch. A value of true(1) indicates that all necessary conditions in the MVR environm… |
| 1.3.6.1.4.1.202.20.66.1.46 | NodedhcpSnoopMgt | |||
| 1.3.6.1.4.1.202.20.66.1.46.1 | NodedhcpSnoopGlobal | |||
| 1.3.6.1.4.1.202.20.66.1.46.1.1 | ScalardhcpSnoopEnable | read-write | current | This object indicates whether the DHCP Snooping feature is enabled. |
| 1.3.6.1.4.1.202.20.66.1.46.1.2 | ScalardhcpSnoopVerifyMacAddressEnable | read-write | current | This object indicates whether DHCP Snooping Mac address verification is enabled. |
| 1.3.6.1.4.1.202.20.66.1.46.1.3 | ScalardhcpSnoopInformationOptionEnable | read-write | current | This object indicates whether the DHCP snooping information option(option 82) feature is enabled. |
| 1.3.6.1.4.1.202.20.66.1.46.1.4 | ScalardhcpSnoopInformationOptionPolicy | read-write | current | This object indicates which reforwarding policy shall be used for DHCP snooping information option(option 82). A value of drop(1) means to drop the DHCP reques… |
| 1.3.6.1.4.1.202.20.66.1.46.2 | NodedhcpSnoopVlan | |||
| 1.3.6.1.4.1.202.20.66.1.46.2.1 | TabledhcpSnoopVlanConfigTable | not-accessible | current | A table contains DHCP Snooping configurations of existing VLANs. |
| 1.3.6.1.4.1.202.20.66.1.46.2.1.1 | RowdhcpSnoopVlanConfigEntry | not-accessible | current | An instance contains the configuration to enable or disable DHCP Snooping at each existing VLAN. |
| 1.3.6.1.4.1.202.20.66.1.46.2.1.1.1 | ColumndhcpSnoopVlanIndex | not-accessible | current | This object indicates the VLAN ID on which DHCP Snooping feature is configured. |
| 1.3.6.1.4.1.202.20.66.1.46.2.1.1.2 | ColumndhcpSnoopVlanEnable | read-write | current | This object indicates whether DHCP Snooping is enabled in this VLAN. |
| 1.3.6.1.4.1.202.20.66.1.46.3 | NodedhcpSnoopInterface | |||
| 1.3.6.1.4.1.202.20.66.1.46.3.1 | TabledhcpSnoopPortConfigTable | not-accessible | current | A table provides the mechanism to configure the trust state of each port or trunk for DHCP Snooping purpose. |
| 1.3.6.1.4.1.202.20.66.1.46.3.1.1 | RowdhcpSnoopPortConfigEntry | not-accessible | current | An instance contains the configuration to enable or disable trust state of each port or trunk for DHCP Snooping purpose. |
| 1.3.6.1.4.1.202.20.66.1.46.3.1.1.1 | ColumndhcpSnoopPortIfIndex | not-accessible | current | The ifIndex value of the port or trunk. |
| 1.3.6.1.4.1.202.20.66.1.46.3.1.1.2 | ColumndhcpSnoopPortTrustEnable | read-write | current | This object indicates whether the port or trunk is trusted for DHCP Snooping purpose. |
| 1.3.6.1.4.1.202.20.66.1.46.4 | NodedhcpSnoopBindings | |||
| 1.3.6.1.4.1.202.20.66.1.46.4.1 | TabledhcpSnoopBindingsTable | not-accessible | current | A table contains the DHCP bindings information learnt by the device. |
| 1.3.6.1.4.1.202.20.66.1.46.4.1.1 | RowdhcpSnoopBindingsEntry | not-accessible | current | An instance contains the Mac address, IP address type, IP address, VLAN number, interface number, leased time and status. |
| 1.3.6.1.4.1.202.20.66.1.46.4.1.1.1 | ColumndhcpSnoopBindingsVlanIndex | not-accessible | current | This object indicates the VLAN which a DHCP client host belongs to. |
| 1.3.6.1.4.1.202.20.66.1.46.4.1.1.2 | ColumndhcpSnoopBindingsMacAddress | not-accessible | current | This object indicates the MAC address of a DHCP client host. |
| 1.3.6.1.4.1.202.20.66.1.46.4.1.1.3 | ColumndhcpSnoopBindingsAddrType | read-only | current | This object indicates the type of IP address denoted in dhcpSnoopBindingsIpAddress type. |
| 1.3.6.1.4.1.202.20.66.1.46.4.1.1.4 | ColumndhcpSnoopBindingsEntryType | read-only | current | This object indicates that this binding is obtained from dynamically learning or is a static configuraion. |
| 1.3.6.1.4.1.202.20.66.1.46.4.1.1.5 | ColumndhcpSnoopBindingsIpAddress | read-only | current | This object indicates the allocated IP address of a DHCP client host. |
| 1.3.6.1.4.1.202.20.66.1.46.4.1.1.6 | ColumndhcpSnoopBindingsPortIfIndex | read-only | current | This object indicates the port or trunk where a DHCP client host connects to. |
| 1.3.6.1.4.1.202.20.66.1.46.4.1.1.7 | ColumndhcpSnoopBindingsLeaseTime | read-only | current | This object indicates the leased time of this DHCP bindings. |
| 1.3.6.1.4.1.202.20.66.1.46.5 | NodedhcpSnoopStatistics | |||
| 1.3.6.1.4.1.202.20.66.1.46.5.1 | ScalardhcpSnoopTotalForwardedPkts | read-only | current | Indicates the total number of packets subjected to DHCP Snooping is forwarded. |
| 1.3.6.1.4.1.202.20.66.1.46.5.3 | ScalardhcpSnoopUntrustedPortDroppedPkts | read-only | current | Indicates the number of packets subjected to DHCP Snooping is dropped because they come from untrusted interface. |
| 1.3.6.1.4.1.202.20.66.1.47 | NodeclusterMgt | |||
| 1.3.6.1.4.1.202.20.66.1.47.1 | ScalarclusterEnable | read-write | current | Enables or disables clustering on the device. |
| 1.3.6.1.4.1.202.20.66.1.47.2 | ScalarclusterCommanderEnable | read-write | current | Enables or disables the device as commander in a cluster. |
| 1.3.6.1.4.1.202.20.66.1.47.4 | ScalarclusterIpPool | read-write | current | The start internal IP address of a cluster pool. |
| 1.3.6.1.4.1.202.20.66.1.47.5 | ScalarclusterClearCandidateTable | read-write | current | Setting this object to clear(2) starts to clear the candidate table. |
| 1.3.6.1.4.1.202.20.66.1.47.6 | ScalarclusterRole | read-only | current | The current role of the device in a cluster. commander(1) : The switch is the controlling device in a cluster. candidate(2) : The switch has been discovered by… |
| 1.3.6.1.4.1.202.20.66.1.47.7 | ScalarclusterMemberCount | read-only | current | The total number of members in a cluster. |
| 1.3.6.1.4.1.202.20.66.1.47.8 | ScalarclusterCandidateCount | read-only | current | The total number of candidates in a cluster. |
| 1.3.6.1.4.1.202.20.66.1.47.9 | TableclusterCandidateTable | not-accessible | current | A table listing cluster candidates. |
| 1.3.6.1.4.1.202.20.66.1.47.9.1 | RowclusterCandidateEntry | not-accessible | current | A conceptual row containing the information of the candidate. |
| 1.3.6.1.4.1.202.20.66.1.47.9.1.1 | ColumnclusterCandidateMacAddr | not-accessible | current | The MAC address of the candidate. |
| 1.3.6.1.4.1.202.20.66.1.47.9.1.3 | ColumnclusterCandidateDesc | read-only | current | The description of the candidate. |
| 1.3.6.1.4.1.202.20.66.1.47.9.1.4 | ColumnclusterCandidateRole | read-only | current | The role of the candidate. candidate(2) : The switch is discovered by the commander, but it has not been manually configured for access from the commander. act… |
| 1.3.6.1.4.1.202.20.66.1.47.10 | TableclusterMemberTable | not-accessible | current | A table listing clustering members. |
| 1.3.6.1.4.1.202.20.66.1.47.10.1 | RowclusterMemberEntry | not-accessible | current | A conceptual row containing the information of the member. |
| 1.3.6.1.4.1.202.20.66.1.47.10.1.1 | ColumnclusterMemberId | not-accessible | current | The ID of the member. |
| 1.3.6.1.4.1.202.20.66.1.47.10.1.2 | ColumnclusterMemberMacAddr | read-only | current | The MAC address of the member. |
| 1.3.6.1.4.1.202.20.66.1.47.10.1.3 | ColumnclusterMemberDesc | read-only | current | The description of the member. |
| 1.3.6.1.4.1.202.20.66.1.47.10.1.4 | ColumnclusterMemberActive | read-only | current | The active status of the member. activeMember(3) : The switch is manually configured for access from the commander and it is active in the cluster. inactiveMem… |
| 1.3.6.1.4.1.202.20.66.1.47.11 | NodeclusterMemberAddCtl | |||
| 1.3.6.1.4.1.202.20.66.1.47.11.1 | ScalarclusterMemberAddCtlMacAddr | read-write | current | The MAC address of the device associated with clusterMemberAddCtlAction. |
| 1.3.6.1.4.1.202.20.66.1.47.11.2 | ScalarclusterMemberAddCtlId | read-write | current | The member id associated with clusterMemberAddCtlAction. |
| 1.3.6.1.4.1.202.20.66.1.47.11.5 | ScalarclusterMemberAddCtlAction | read-write | current | Adds the device to members that can be accessed from the commander. The MAC of the device is the current value of clusterMemberAddCtlMacAddr and the assigned m… |
| 1.3.6.1.4.1.202.20.66.1.47.12 | NodeclusterMemberRemoveCtl | |||
| 1.3.6.1.4.1.202.20.66.1.47.12.1 | ScalarclusterMemberRemoveCtlId | read-write | current | The member ID associated with clusterMemberRemoveCtlAction. |
| 1.3.6.1.4.1.202.20.66.1.47.12.2 | ScalarclusterMemberRemoveCtlAction | read-write | current | Removes the device from members that can be accessed from the commander. The member ID is the current value of clusterMemberRemoveCtlId. Set this object to rem… |
| 1.3.6.1.4.1.202.20.66.1.48 | NodeipSrcGuardMgt | |||
| 1.3.6.1.4.1.202.20.66.1.48.1 | TableipSrcGuardConfigTable | not-accessible | current | A table contains the configurations to enable or disable IP Source Guard at each port or trunk. |
| 1.3.6.1.4.1.202.20.66.1.48.1.1 | RowipSrcGuardConfigEntry | not-accessible | current | An instance contains the configuration to enable or disable IP Source Guard at each port or trunk. |
| 1.3.6.1.4.1.202.20.66.1.48.1.1.1 | ColumnipSrcGuardPortIfIndex | not-accessible | current | This object idents the port or trunk which is capable of IP Source Guard feature. |
| 1.3.6.1.4.1.202.20.66.1.48.1.1.2 | ColumnipSrcGuardMode | read-write | current | This object indicates whether Ip Source Guard is enabled at this interface. If the value equals 0, it means Ip Source Guard is disabled. If the value equals 1,… |
| 1.3.6.1.4.1.202.20.66.1.48.2 | TableipSrcGuardAddrTable | not-accessible | current | A table contains the IP Source Guard bindings information learnt by the device. |
| 1.3.6.1.4.1.202.20.66.1.48.2.1 | RowipSrcGuardAddrEntry | not-accessible | current | An instance contains the Mac address, IP address type, IP address, VLAN number, interface number, leased time and status. |
| 1.3.6.1.4.1.202.20.66.1.48.2.1.1 | ColumnipSrcGuardBindingsVlanIndex | not-accessible | current | This object indicates the VLAN which a DHCP client host belongs to. |
| 1.3.6.1.4.1.202.20.66.1.48.2.1.2 | ColumnipSrcGuardBindingsMacAddress | not-accessible | current | This object indicates the MAC address of a DHCP client host. |
| 1.3.6.1.4.1.202.20.66.1.48.2.1.3 | ColumnipSrcGuardBindingsAddrType | read-create | current | This object indicates the type of IP address denoted in ipSrcGuardBindingsIpAddress type. |
| 1.3.6.1.4.1.202.20.66.1.48.2.1.4 | ColumnipSrcGuardBindingsEntryType | read-only | current | This object indicates that this binding is obtained from dynamically learning or is a static configuraion. |
| 1.3.6.1.4.1.202.20.66.1.48.2.1.5 | ColumnipSrcGuardBindingsIpAddress | read-create | current | This object indicates the allocated IP address of a DHCP client host. |
| 1.3.6.1.4.1.202.20.66.1.48.2.1.6 | ColumnipSrcGuardBindingsPortIfIndex | read-create | current | This object indicates the port or trunk where a DHCP client host connects to. |
| 1.3.6.1.4.1.202.20.66.1.48.2.1.7 | ColumnipSrcGuardBindingsLeaseTime | read-only | current | This object indicates the leased time of this DHCP bindings. |
| 1.3.6.1.4.1.202.20.66.1.48.2.1.8 | ColumnipSrcGuardBindingsStatus | read-create | current | The status of this conceptual row entry. This object issued to manage the creation and deletion of conceptual rows. The status column has six defined values: -… |
| 1.3.6.1.4.1.202.20.66.2 | Nodesmc6152L2Notifications | |||
| 1.3.6.1.4.1.202.20.66.2.1 | Nodesmc6152L2Traps | |||
| 1.3.6.1.4.1.202.20.66.2.1.0 | Nodesmc6152L2TrapsPrefix | |||
| 1.3.6.1.4.1.202.20.66.2.1.0.1 | NotificationswPowerStatusChangeTrap | current | This trap is sent when the power state changes. | |
| 1.3.6.1.4.1.202.20.66.2.1.0.36 | NotificationswPortSecurityTrap | current | This trap is sent when the port is being intruded. This trap will only be sent when the portSecActionTrap is enabled. | |
| 1.3.6.1.4.1.202.20.66.3 | Nodesmc6152L2Conformance |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| FileCopyStatus | INTEGER { fileCopyTftpUndefError(1), fileCopyTftpFileNotFound(2), fileCopyTftpAccessViolation(3), fileCopyTftpDiskFull(4), fileCopyTftpIllegalOperation(5), fileCopyTftpUnkownTransferId(6), fileCopyTftpFileExisted(7), fileCopyTftpNoSuchUser(8), fileCopyTftpTimeout(9), fileCopyTftpSendError(10), fileCopyTftpReceiverError(11), fileCopyTftpSocketOpenError(12), fileCopyTftpSocketBindError(13), fileCopyTftpUserCancel(14), fileCopyTftpCompleted(15), fileCopyParaError(16), fileCopyBusy(17), fileCopyUnknown(18), fileCopyReadFileError(19), fileCopySetStartupError(20), fileCopyFileSizeExceed(21), fileCopyMagicWordError(22), fileCopyImageTypeError(23), fileCopyHeaderChecksumError(24), fileCopyImageChecksumError(25), fileCopyWriteFlashFinish(26), fileCopyWriteFlashError(27), fileCopyWriteFlashProgramming(28), fileCopyError(29), fileCopySuccess(30), fileCopyCompleted(31) } | current | The file copy result status. |
| KeySegment | DisplayString(SIZE(0..128)) | current | The total length of the key is 1024 characters, it is divided into 8 parts and stored in 8 separated mib variables as below: Key1: part 1 of the key (1-128) Key2: part 2 of the key (129-256) Key3: part 3 of the key (257… |
| StaPathCostMode | INTEGER { short(1), long(2) } | current | The path cost mode of a spanning tree algorithm, short(1) indicates that we retrieve/configure the spanning tree path cost as a 16 bit value and long(2) indicates that we retrieve/configure the spanning tree path cost a… |
| ValidStatus | INTEGER { valid(1), invalid(2) } | current | A simple status value for the object to create and destroy a table entry. This is a simplified variant of RowStatus as it supports only two values. Setting it to valid(1) creates an entry. Setting it to invalid(2) destr… |