SUPERMICRO-IPV6-MIB
262 objects
The MIB module for IPv6.
Imported Objects
| IF-MIB | InterfaceIndex |
| INET-ADDRESS-MIB | InetScopeType InetZoneIndex |
| SNMPv2-SMI | Counter32 enterprises Integer32 MODULE-IDENTITY OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | DisplayString RowStatus TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.10876.101.1.28 | Identityfutureipv6 | The MIB module for IPv6. | ||
| 1.3.6.1.4.1.10876.101.1.28.1 | Nodefsipv6 | |||
| 1.3.6.1.4.1.10876.101.1.28.1.1 | Nodefsipv6Scalars | |||
| 1.3.6.1.4.1.10876.101.1.28.1.1.1 | Scalarfsipv6NdCacheMaxRetries | read-write | current | This object specifies the maximum number of retries that can be attempted upon resolving the 'physical' address of an IPv6 address during address resolution or… |
| 1.3.6.1.4.1.10876.101.1.28.1.1.2 | Scalarfsipv6PmtuConfigStatus | read-write | current | Flag to enable or disable Path MTU Discovery for the node. |
| 1.3.6.1.4.1.10876.101.1.28.1.1.3 | Scalarfsipv6PmtuTimeOutInterval | read-write | current | The time in minutes after which the path MTU entry times out. |
| 1.3.6.1.4.1.10876.101.1.28.1.1.4 | Scalarfsipv6JumboEnable | read-write | current | Flag to enable or disable IPv6 Jumbogram facility for the node. |
| 1.3.6.1.4.1.10876.101.1.28.1.1.5 | Scalarfsipv6NumOfSendJumbo | read-only | current | Number of IPv6 Jumbograms sent from the node. |
| 1.3.6.1.4.1.10876.101.1.28.1.1.6 | Scalarfsipv6NumOfRecvJumbo | read-only | current | Number of IPv6 Jumbograms received. |
| 1.3.6.1.4.1.10876.101.1.28.1.1.7 | Scalarfsipv6ErrJumbo | read-only | current | Number of IPv6 Error Jumbograms received or transmitted. |
| 1.3.6.1.4.1.10876.101.1.28.1.1.8 | Scalarfsipv6GlobalDebug | read-write | current | Enables the tracing in the selected submodule in IP6. A 32 bit integer is used to store the Tracing level in the specified module. Different Tracing Levels - B… |
| 1.3.6.1.4.1.10876.101.1.28.1.1.9 | Scalarfsipv6MaxRouteEntries | read-write | current | Maximum Number of Route Entries that could be configured in the system. Minumum value is 5. |
| 1.3.6.1.4.1.10876.101.1.28.1.1.10 | Scalarfsipv6MaxLogicalIfaces | read-write | current | Maximum Number of configurable Logical IPv6 Interfaces |
| 1.3.6.1.4.1.10876.101.1.28.1.1.11 | Scalarfsipv6MaxTunnelIfaces | read-write | current | Maximum Number of configurable Tunnel Interfaces |
| 1.3.6.1.4.1.10876.101.1.28.1.1.12 | Scalarfsipv6MaxAddresses | read-write | current | Maximum Number of Configurable IPv6 Interfaces. |
| 1.3.6.1.4.1.10876.101.1.28.1.1.13 | Scalarfsipv6MaxFragReasmEntries | read-write | current | This object could be used for 2 purpose. 1. Maximum Number of IP6 datagrams awaiting reassembly. 2. Maximum Number of fragments that could be allowed in a sing… |
| 1.3.6.1.4.1.10876.101.1.28.1.1.14 | Scalarfsipv6Nd6MaxCacheEntries | read-write | current | Maximum Number of ND Cache Entries. |
| 1.3.6.1.4.1.10876.101.1.28.1.1.15 | Scalarfsipv6PmtuMaxDest | read-write | current | Maximum Number of PMTU Table Entries |
| 1.3.6.1.4.1.10876.101.1.28.1.1.16 | Scalarfsipv6RFC5095Compatibility | read-write | current | When the IPv6 node is configured to be RFC5095 compatible, then it should treat Type 0 Routing Header as invalid routing header type. |
| 1.3.6.1.4.1.10876.101.1.28.1.2 | Nodefsipv6Tables | |||
| 1.3.6.1.4.1.10876.101.1.28.1.2.1 | Tablefsipv6IfTable | not-accessible | current | The IPv6 Interface table contains information on the entity's internetwork-layer interfaces on which IPv6. protocol is enabled. An IPv6 interface constitutes a… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1 | Rowfsipv6IfEntry | not-accessible | current | An interface entry containing objects about a particular IPv6 interface. The entry is created or deleted from SNMP. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.1 | Columnfsipv6IfIndex | not-accessible | current | A unique value identifying the particular IPv6 interface. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.2 | Columnfsipv6IfType | read-only | current | The type of interface immediately `below' the network layer in the protocol stack. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.3 | Columnfsipv6IfPortNum | read-only | current | This object identifies the 'interface' over which this network interface operates and is dependent on the value of fsipv6IfType. This object reflects the ifind… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.4 | Columnfsipv6IfCircuitNum | read-only | current | This object identifies the circuit over which this network interface operates and is dependent on the value of fsipv6IfType. If the data-link layer is Ethernet… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.5 | Columnfsipv6IfToken | read-write | current | The address token for this interface that is (at least) unique on the link this interface is attached to. This token can be specified only if the fsipv6IfType … |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.6 | Columnfsipv6IfAdminStatus | read-write | current | Indicates whether IPv6 is enabled/disabled on this interface. When lower layer indicates the creation of the interface, an entry will be create in IPv6 interfa… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.7 | Columnfsipv6IfOperStatus | read-only | current | The operational state of interface. It is up(1) if the fsipv6IfAdminStatus is 'up' and the layer below the network layer is also operational. Otherwise it is d… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.8 | Columnfsipv6IfRouterAdvStatus | read-write | current | The router advertisement status on this interface. When the object is set to enabled(1), router advertisements can be allowed on the IPv6 interface. Otherwise,… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.9 | Columnfsipv6IfRouterAdvFlags | read-write | current | This object specifies the bits to be set in the router advertisements sent by this entity on this interface. M-bit set in the router advertisement indicates ho… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.10 | Columnfsipv6IfHopLimit | read-write | current | The Hop Limit value to be placed in the router advertisements sent on this IPv6 interface. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.11 | Columnfsipv6IfDefRouterTime | read-write | current | The default router time to be indicated in the router advertisements sent on this IPv6 interface. This defines the time in seconds for which this entity acts a… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.12 | Columnfsipv6IfReachableTime | read-write | current | The reachable time to be indicated in the router advertisements sent on this IPv6 interface and also used by this entity. This defines the time in seconds that… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.13 | Columnfsipv6IfRetransmitTime | read-write | current | The retransmit time to be indicated in the router advertisements sent on this IPv6 interface and also used by this entity. This defines the time in seconds bet… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.14 | Columnfsipv6IfDelayProbeTime | read-write | current | The time in seconds to delay before starting unreachability probing of neighbor entries which are stale. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.15 | Columnfsipv6IfPrefixAdvStatus | read-write | current | The prefix advertisement status on this IPv6 interface. Object value enabled(1) allows the configured prefixes to be advertised in router advertisements. Other… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.16 | Columnfsipv6IfMinRouterAdvTime | read-write | current | The minimum time in seconds allowed between sending unsolicited router advertisements.The default value is one-third the default value of fsipv6IfMaxRouterAdvT… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.17 | Columnfsipv6IfMaxRouterAdvTime | read-write | current | The maximum time in seconds between sending unsolicited router advertisements. Router advertisements are sent periodically at a random interval between the val… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.18 | Columnfsipv6IfDADRetries | read-write | current | The maximum number of neighbor solicitations sent for the purpose of duplicate address detection on a tentative address. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.19 | Columnfsipv6IfForwarding | read-write | current | This MIB object is used to configure IPv6 routing and forwarding on this interface. The default value is set to enabled. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.20 | Columnfsipv6IfRoutingStatus | read-only | current | This MIB object indicates the current routing status on this interface. This is based on the global IPv6 forwarding status of the mib object 'ipv6Forwarding'. … |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.21 | Columnfsipv6IfIcmpErrInterval | read-write | current | Time interval between tokens being added to the ICMPv6 token bucket. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.22 | Columnfsipv6IfIcmpTokenBucketSize | read-write | current | Maximum number of tokens stored in the ICMPv6 bucket |
| 1.3.6.1.4.1.10876.101.1.28.1.2.1.1.23 | Columnfsipv6IfDestUnreachableMsg | read-write | current | Indicates whether ICMPv6 destination unreachable messages are enabled/disabled on this interface. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2 | Tablefsipv6IfStatsTable | not-accessible | current | IPv6 interface traffic statistics |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1 | Rowfsipv6IfStatsEntry | not-accessible | current | An interface statistics entry containing objects at a particular IPv6 interface. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.1 | Columnfsipv6IfStatsIndex | not-accessible | current | The index value which uniquely identifies the IPv6 interface for which this statistics are maintained. The interface identified by a particular value of this i… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.2 | Columnfsipv6IfStatsInReceives | read-only | current | The total number of input datagrams received from interfaces, including those received in error. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.3 | Columnfsipv6IfStatsInHdrErrors | read-only | current | The number of input datagrams discarded due to errors in their IPv6 headers, including version number mismatch, other format errors, hop count exceeded, errors… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.4 | Columnfsipv6IfStatsTooBigErrors | read-only | current | The number of datagrams that could not be forwarded because their size exceeded the Path MTU |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.5 | Columnfsipv6IfStatsInAddrErrors | read-only | current | The number of input datagrams discarded because the IPv6 address in their IPv6 header's destination field was not a valid address to be received at this entity… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.6 | Columnfsipv6IfStatsForwDatagrams | read-only | current | The number of input datagrams for which this entity was not their final IPv6 destination, as a result of which an attempt was made to find a route to forward t… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.7 | Columnfsipv6IfStatsInUnknownProtos | read-only | current | The number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.8 | Columnfsipv6IfStatsInDiscards | read-only | current | The number of input IPv6 datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (e.g., for lack of bu… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.9 | Columnfsipv6IfStatsInDelivers | read-only | current | The total number of input datagrams successfully delivered to IPv6 user-protocols (including ICMP). |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.10 | Columnfsipv6IfStatsOutRequests | read-only | current | The total number of IPv6 datagrams which local IPv6 user-protocols (including ICMP) supplied to IPv6 in requests for transmission. Note that this counter does … |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.11 | Columnfsipv6IfStatsOutDiscards | read-only | current | The number of output IPv6 datagrams for which no problem was encountered to prevent their transmission to their destination, but which were discarded (e.g., fo… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.12 | Columnfsipv6IfStatsOutNoRoutes | read-only | current | The number of IPv6 datagrams discarded because no route could be found to transmit them to their destination. Note that this counter includes any packets count… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.13 | Columnfsipv6IfStatsReasmReqds | read-only | current | The number of IPv6 fragments received which needed to be reassembled at this entity. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.14 | Columnfsipv6IfStatsReasmOKs | read-only | current | The number of IPv6 datagrams successfully reassembled. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.15 | Columnfsipv6IfStatsReasmFails | read-only | current | The number of failures detected by the IPv6 re- assembly algorithm (for whatever reason: timed out, errors, etc). Note that this is not necessarily a count of … |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.16 | Columnfsipv6IfStatsFragOKs | read-only | current | The number of IPv6 datagrams that have been successfully fragmented at this entity. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.17 | Columnfsipv6IfStatsFragFails | read-only | current | The number of IPv6 datagrams that have been discarded because they needed to be fragmented at this entity but could not be. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.18 | Columnfsipv6IfStatsFragCreates | read-only | current | The number of IPv6 datagram fragments that have been generated as a result of fragmentation at this entity. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.19 | Columnfsipv6IfStatsInMcastPkts | read-only | current | The number of multicast packets received by the interface |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.20 | Columnfsipv6IfStatsOutMcastPkts | read-only | current | The number of multicast packets transmitted by the interface |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.21 | Columnfsipv6IfStatsInTruncatedPkts | read-only | current | The number of input datagrams discarded because datagram frame didn't carry enough data |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.22 | Columnfsipv6IfStatsInRouterSols | read-only | current | The number of ICMP Router Solicit messages received. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.23 | Columnfsipv6IfStatsInRouterAdvs | read-only | current | The number of ICMP Router Advertisement messages received. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.24 | Columnfsipv6IfStatsInNeighSols | read-only | current | The number of ICMP Neighbor Solicit messages received. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.25 | Columnfsipv6IfStatsInNeighAdvs | read-only | current | The number of ICMP Neighbor Advertisement messages received. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.26 | Columnfsipv6IfStatsInRedirects | read-only | current | The number of ICMP Redirect messages received. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.27 | Columnfsipv6IfStatsOutRouterSols | read-only | current | The number of ICMP Router Solicit messages sent. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.28 | Columnfsipv6IfStatsOutRouterAdvs | read-only | current | The number of ICMP Router Advertisement messages sent. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.29 | Columnfsipv6IfStatsOutNeighSols | read-only | current | The number of ICMP Neighbor Solicitation messages sent. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.30 | Columnfsipv6IfStatsOutNeighAdvs | read-only | current | The number of ICMP Neighbor Advertisement messages sent. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.31 | Columnfsipv6IfStatsOutRedirects | read-only | current | The number of Redirect messages sent. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.32 | Columnfsipv6IfStatsLastRouterAdvTime | read-only | current | The time at which the last Periodic router advertisement was sent. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.33 | Columnfsipv6IfStatsNextRouterAdvTime | read-only | current | The time at which the next Periodic router advertisement is scheduled to be sent. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.2.1.34 | Columnfsipv6IfStatsIcmp6ErrRateLmtd | read-only | current | No of rate limited ICMP6 error messages |
| 1.3.6.1.4.1.10876.101.1.28.1.2.3 | Tablefsipv6PrefixTable | not-accessible | current | The table containing entity's IPv6 address prefix information. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.3.1 | Rowfsipv6PrefixEntry | not-accessible | current | The entry in the IPv6 Address Prefix Table which defines a prefix to be advertised in the route advertisement message send on an IPv6 interface. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.3.1.1 | Columnfsipv6PrefixIndex | not-accessible | current | The index value which uniquely identifies the IPv6 interface on which this IPv6 address prefix entry is to be advertised. The interface identified by a particu… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.3.1.2 | Columnfsipv6PrefixAddress | not-accessible | current | The IPv6 address prefix to which this entry's prefix information pertains. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.3.1.3 | Columnfsipv6PrefixAddrLen | not-accessible | current | The length of the prefix (in bits) associated with the IPv6 address prefix of this entry. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.3.1.4 | Columnfsipv6PrefixProfileIndex | read-write | current | Indicates the index into the IPv6 Address Profile Table. This entry of the IPv6 Address Profile table defines the parameters for this prefix. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.3.1.5 | Columnfsipv6PrefixAdminStatus | read-create | current | Indicates the administrative status of the prefix. CreateAndGo and NotInService are not supported. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.3.1.6 | Columnfsipv6SupportEmbeddedRp | read-write | current | Flag to control the usage of associated IPv6 Prefix address as a valid embedded-RP prefix on specified interface |
| 1.3.6.1.4.1.10876.101.1.28.1.2.4 | Tablefsipv6AddrTable | not-accessible | current | The table containing entity's IPv6 addressing information. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.4.1 | Rowfsipv6AddrEntry | not-accessible | current | The entry in the IPv6 Address Table which defines a unicast, anycast or link-local address on an IPv6 interface. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.4.1.1 | Columnfsipv6AddrIndex | not-accessible | current | The index value which uniquely identifies the IPv6 interface on which this IPv6 address entry exists. The interface identified by a particular value of this in… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.4.1.2 | Columnfsipv6AddrAddress | not-accessible | current | The IPv6 address to which this entry's addressing information pertains. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.4.1.3 | Columnfsipv6AddrPrefixLen | not-accessible | current | The length of the prefix (in bits) associated with the IPv6 address of this entry. For a link-local address, the prefix is always start with '0xfe80' and the p… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.4.1.4 | Columnfsipv6AddrAdminStatus | read-create | current | Indicates the desired status of the address. Also a creation of an address can trigger IPv6 to be enabled over the interface. Similarly deletion of all the add… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.4.1.5 | Columnfsipv6AddrType | read-write | current | Indicates whether the address is a unicast, anycast or link-local address. Syntactically there is no difference between a unicast address and a anycast address… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.4.1.6 | Columnfsipv6AddrProfIndex | read-write | current | Indicates the index into the IPv6 Address Profile Table. This entry of the IPv6 Address Profile table defines the parameters for this address. For a link-local… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.4.1.7 | Columnfsipv6AddrOperStatus | read-only | current | Indicates the operational status of the address. A status of failed(4) indicates that a duplicate address has been detected on this IPv6 interface. On interfac… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.4.1.8 | Columnfsipv6AddrScope | read-only | current | Scope is a 4-bit value that describes the scope of an IPV6 address.An unicast address can possibly have 2 scopes (Linklocal and Global) only. A multicast addre… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.5 | Tablefsipv6AddrProfileTable | not-accessible | current | The table containing information for an address or set of addresses of the entity. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.5.1 | Rowfsipv6AddrProfileEntry | not-accessible | current | The entry in the IPv6 Address Profile Table which contains parameters related to the advertisement of address prefixes. One or more IPv6 addresses refer to thi… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.5.1.1 | Columnfsipv6AddrProfileIndex | not-accessible | current | A unique value identifying the particular IPv6 Address profile entry. This is referred by fsipv6AddrProfIndex of IPv6 Address Table. The index 0 is created wit… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.5.1.2 | Columnfsipv6AddrProfileStatus | read-write | current | Indicates that the entry is valid or not. An entry other than the first entry can be deleted by setting this object to invalid(2). |
| 1.3.6.1.4.1.10876.101.1.28.1.2.5.1.3 | Columnfsipv6AddrProfilePrefixAdvStatus | read-write | current | If this object has value on(1), the address prefixes corresponding to those addresses which use this profile will be advertised in router advertisements sent b… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.5.1.4 | Columnfsipv6AddrProfileOnLinkAdvStatus | read-write | current | If this object has value on(1), the address prefixes corresponding to those addresses which use this profile will be advertised with on-link flag set in the ro… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.5.1.5 | Columnfsipv6AddrProfileAutoConfAdvStatus | read-write | current | If this object has value on(1), the address prefixes corresponding to those addresses which use this profile will be advertised with autonomous address configu… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.5.1.6 | Columnfsipv6AddrProfilePreferredTime | read-write | current | This object specifies the preferred lifetime in seconds for the address prefixes corresponding to those addresses which use this profile. This is sent in route… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.5.1.7 | Columnfsipv6AddrProfileValidTime | read-write | current | This object specifies the valid lifetime in seconds for the address prefixes corresponding to those addresses which use this profile. This is sent in router ad… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.5.1.8 | Columnfsipv6AddrProfileValidLifeTimeFlag | read-write | current | By setting this flag to fixed (1),the router advertisement Valid life time value is set to fixed and by setting to variable(2), the router advertisement Valid … |
| 1.3.6.1.4.1.10876.101.1.28.1.2.5.1.9 | Columnfsipv6AddrProfilePreferredLifeTimeFlag | read-write | current | By setting this flag to fixed (1),the router advertisement Preferred life time value is set to fixed and by setting to variable(2), the router advertisement pr… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.6 | Tablefsipv6PmtuTable | not-accessible | current | IPv6 Path MTU table. This table contains an entry for a specific path traversed by packets exchanged between the source and destination nodes. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.6.1 | Rowfsipv6PmtuEntry | not-accessible | current | A Path MTU entry. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.6.1.1 | Columnfsipv6PmtuDest | not-accessible | current | The destination IPv6 address of the packets to be exchanged. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.6.1.2 | Columnfsipv6Pmtu | read-write | current | Indicates the path MTU value for the path. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.6.1.3 | Columnfsipv6PmtuTimeStamp | read-only | current | Indicates the entry created time in the PMTU table. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.6.1.4 | Columnfsipv6PmtuAdminStatus | read-write | current | The desired status of the PmtuTable. This variable has to be made valid(1) for creating a entry in the PmtuTable. If set to invalid(2), the entry is deleted. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.7 | Tablefsipv6NdLanCacheTable | not-accessible | current | The IPv6 Address Translation table used for mapping from IPv6 addresses to physical addresses on Ethernet. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.7.1 | Rowfsipv6NdLanCacheEntry | not-accessible | current | Each entry contains one IPv6 address to `physical' address equivalence. Entries are created dynamically upon address resolution or statically from SNMP. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.7.1.1 | Columnfsipv6NdLanCacheIfIndex | not-accessible | current | The index value which uniquely identifies the IPv6 interface on which this fsipv6NdLanCache entry exists. The interface identified by a particular value of thi… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.7.1.2 | Columnfsipv6NdLanCacheIPv6Addr | not-accessible | current | The IPv6 Address corresponding to the `physical' address on Ethernet. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.7.1.3 | Columnfsipv6NdLanCacheStatus | read-write | current | Setting this object to the value invalid(2) effects in invalidating the corresponding entry in the fsipv6NdLanCacheTable. Otherwise, the entry remains valid. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.7.1.4 | Columnfsipv6NdLanCachePhysAddr | read-write | current | The `physical' address on Ethernet. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.7.1.5 | Columnfsipv6NdLanCacheState | read-only | current | The reachability state of NdLanCacheEntry. Upon creation of an entry from SNMP, this object takes the value as 'static'. Otherwise takes the value that corresp… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.7.1.6 | Columnfsipv6NdLanCacheUseTime | read-only | current | The value of sysUpTime at the time the entry was consulted upon IPv6 packet forwarding. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.8 | Tablefsipv6NdWanCacheTable | not-accessible | current | The IPv6 Address Translation table used for mapping from IPv6 addresses to physical addresses on NBMA interface. The 'physical address' actually refers to the … |
| 1.3.6.1.4.1.10876.101.1.28.1.2.8.1 | Rowfsipv6NdWanCacheEntry | not-accessible | current | Each entry contains one IPv6 address to `physical' address equivalence. Entries are created dynamically upon reception of IPv6 packet from an on-link source or… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.8.1.1 | Columnfsipv6NdWanCacheIfIndex | not-accessible | current | The index value which uniquely identifies the IPv6 interface on which this fsipv6NdWanCache entry exists. The interface identified by a particular value of thi… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.8.1.2 | Columnfsipv6NdWanCacheIPv6Addr | not-accessible | current | The IPv6 Address of the on-link node on this NBMA interface. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.8.1.3 | Columnfsipv6NdWanCacheStatus | read-write | current | Setting this object to the value 'invalid(2)' effects in invalidating the corresponding entry in the fsipv6NdWanCacheTable. Otherwise, the entry remains valid. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.8.1.4 | Columnfsipv6NdWanCacheState | read-only | current | The reachability state of NdWanCacheEntry. Upon creation of an entry from SNMP, this object takes the value as 'static'. Otherwise takes the value as 'reachabl… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.8.1.5 | Columnfsipv6NdWanCacheUseTime | read-only | current | The value of sysUpTime at the time the entry was consulted upon IPv6 packet forwarding. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.12 | Tablefsipv6PingTable | not-accessible | current | This entity's IPv6 Ping Table. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.12.1 | Rowfsipv6PingEntry | not-accessible | current | Contains the information about a particular IPv6 Ping operation. An entry is created/deleted from SNMP. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.12.1.1 | Columnfsipv6PingIndex | not-accessible | current | A unique value identifying the particular IPv6 Ping entry. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.12.1.2 | Columnfsipv6PingDest | read-write | current | The IPv6 address of the destination to be pinged. This should be a unicast or link-local address |
| 1.3.6.1.4.1.10876.101.1.28.1.2.12.1.3 | Columnfsipv6PingIfIndex | read-write | current | The index value which uniquely identifies the IPv6 interface on which this Ping is to be sent. The interface identified by a particular value of this index is … |
| 1.3.6.1.4.1.10876.101.1.28.1.2.12.1.4 | Columnfsipv6PingAdminStatus | read-write | current | The desired status for the ping operation. This variable has to be made up(1) for starting the ping operation. If set to down(2), the ping is stopped but the s… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.12.1.5 | Columnfsipv6PingInterval | read-write | current | The time interval in seconds between successive pings sent to the destination. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.12.1.6 | Columnfsipv6PingRcvTimeout | read-write | current | The time in seconds after which this entity times out waiting for a particular ping response. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.12.1.7 | Columnfsipv6PingTries | read-write | current | The number of times the destination is to be pinged. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.12.1.8 | Columnfsipv6PingSize | read-write | current | The size of the data portion of the Ping packet. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.12.1.9 | Columnfsipv6PingSentCount | read-only | current | Total number of packets sent to destination. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.12.1.10 | Columnfsipv6PingAverageTime | read-only | current | The average value of the round trip time in seconds to this destination. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.12.1.11 | Columnfsipv6PingMaxTime | read-only | current | The maximum value of the round trip time in seconds to this destination. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.12.1.12 | Columnfsipv6PingMinTime | read-only | current | The minimum value of the round trip time in seconds to this destination. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.12.1.13 | Columnfsipv6PingOperStatus | read-only | current | The current status of this ping operation. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.12.1.14 | Columnfsipv6PingSuccesses | read-only | current | The number of ping responses received. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.12.1.15 | Columnfsipv6PingPercentageLoss | read-only | current | Percentage of lost packets for which no responses were received till timeout. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.12.1.16 | Columnfsipv6PingData | read-write | current | Data that should be sent in the Ping message |
| 1.3.6.1.4.1.10876.101.1.28.1.2.12.1.17 | Columnfsipv6PingSrcAddr | read-write | current | Source address to be used for the ping |
| 1.3.6.1.4.1.10876.101.1.28.1.2.12.1.18 | Columnfsipv6PingZoneId | read-write | current | Zone-Id shoule be able to identify a particular zone of the address's scope. This Zone id applies to all kinds of unicast and multicast addresses of non-global… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.12.1.19 | Columnfsipv6PingDestAddrType | read-write | current | The address type of the destination to be pinged. other - unicast or linklocal address anycast - anycast address .An IPv6 packet cannot have anycast address as… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.13 | Tablefsipv6NDProxyListTable | not-accessible | current | Configurable list of IPv6 Addresses for which Proxy Neighbor Discovery is desired. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.13.1 | Rowfsipv6NDProxyListEntry | not-accessible | current | An entry in the ND Proxy Table. Each entry specifies the IPv6 address for which proxy feature is needed, and the adminstatus for the row. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.13.1.1 | Columnfsipv6NdProxyAddr | not-accessible | current | IPv6 address for Proxy ND. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.13.1.2 | Columnfsipv6NdProxyAdminStatus | read-write | current | The desired state of the ND Proxy list entry. When set to create(4) the IPv6 interface is created and invalid(4) to delete the interface. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.14 | Tablefsipv6AddrSelPolicyTable | not-accessible | current | This table is used for default address selection in IPv6. This table is used to configure the Precedence and Label associated with a source/destination address… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.14.1 | Rowfsipv6AddrSelPolicyEntry | not-accessible | current | This table entry is used to configure the following parameters for an IPv6 source/destination address - Prefix, PrefixLen,Ifindex,Preference,Label,Address Type… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.14.1.1 | Columnfsipv6AddrSelPolicyPrefix | not-accessible | current | The IPv6 Address/Prefix for which the policy needs to be configured. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.14.1.2 | Columnfsipv6AddrSelPolicyPrefixLen | not-accessible | current | The Prefix length associated with the IPV6 address identified by 'fsipv6AddrSelPolicyPrefix. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.14.1.3 | Columnfsipv6AddrSelPolicyIfIndex | not-accessible | current | The index value that uniquely identifies the interface to which this entry is applicable. A value of 0 indicates that the associated address is reachable via a… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.14.1.4 | Columnfsipv6AddrSelPolicyScope | read-only | current | This MIB object identifies the scope of the IPv6 address. This can take the following values based on whether the address is unicast/anycast or multicast. 0 re… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.14.1.5 | Columnfsipv6AddrSelPolicyPrecedence | read-write | current | The precedence value associated with the address in the policy table. This value is applicable for destination addresses.Higher the value, higher the precedenc… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.14.1.6 | Columnfsipv6AddrSelPolicyLabel | read-write | current | The label value associated with the address in the policy table. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.14.1.7 | Columnfsipv6AddrSelPolicyAddrType | read-write | current | This MIB object is used to configure an address as unicast/anycast/multicast, provided the IPv6 address meets the validation criteria for the address type. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.14.1.8 | Columnfsipv6AddrSelPolicyIsPublicAddr | read-only | current | This MIB object indicates whether the address configured in the policy table is a private or public address. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.14.1.9 | Columnfsipv6AddrSelPolicyIsSelfAddr | read-only | current | This MIB object indicates whether the given address is configured on the associated interface and represents a self-address. The associated MIB object fsipv6Ad… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.14.1.10 | Columnfsipv6AddrSelPolicyReachabilityStatus | read-only | current | This MIB object indicates whether the address configured in the Policy Table is reachable/unreachable |
| 1.3.6.1.4.1.10876.101.1.28.1.2.14.1.11 | Columnfsipv6AddrSelPolicyConfigStatus | read-only | current | This MIB object indicates whether the associated entry in the Policy table is created automatically or via the administrator. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.14.1.12 | Columnfsipv6AddrSelPolicyRowStatus | read-create | current | Administrative Status of the policy table. This object is used to create or delete the entry in the policy table. The following values are not supported for th… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.15 | Tablefsipv6IfScopeZoneMapTable | not-accessible | current | A zone index identifies an instance of a specific scope uniquely within the system.The zone index is used to associate unambiguously an IPv6 address to a speci… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.15.1 | Rowfsipv6IfScopeZoneMapEntry | not-accessible | current | Each entry contains the list of scope identifiers on a given interface. Its a unique value assigned for each scope on an interface. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.15.1.1 | Columnfsipv6ScopeZoneIndexIfIndex | not-accessible | current | The index value that uniquely identifies the interface to which these scopes belong. The interface identified by a particular value of this index is the same i… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.15.1.2 | Columnfsipv6ScopeZoneIndexInterfaceLocal | read-write | current | The zone index for the Interface local scope on this interface. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.15.1.3 | Columnfsipv6ScopeZoneIndexLinkLocal | read-write | current | The zone index for the link-local scope on this interface. The index value corresponding to this scope-zone can be known from ipv6ScopeZoneIndexLinkLocal |
| 1.3.6.1.4.1.10876.101.1.28.1.2.15.1.4 | Columnfsipv6ScopeZoneIndex3 | read-write | current | The zone index for scope 3 on this interface. The index value corresponding to this scope-zone can be known from ipv6ScopeZoneIndex3 |
| 1.3.6.1.4.1.10876.101.1.28.1.2.15.1.5 | Columnfsipv6ScopeZoneIndexAdminLocal | read-write | current | The zone index for the admin-local scope on this interface.The index value corresponding to this scope-zone can be known from ipv6ScopeZoneIndexAdminLocal |
| 1.3.6.1.4.1.10876.101.1.28.1.2.15.1.6 | Columnfsipv6ScopeZoneIndexSiteLocal | read-write | current | The zone index for the site-local scope on this interface.The index value corresponding to this scope-zone can be known from ipv6ScopeZoneIndexSiteLocal |
| 1.3.6.1.4.1.10876.101.1.28.1.2.15.1.7 | Columnfsipv6ScopeZoneIndex6 | read-write | current | The zone index for scope 6 on this interface.The index value corresponding to this scope-zone can be known from ipv6ScopeZoneIndex6 |
| 1.3.6.1.4.1.10876.101.1.28.1.2.15.1.8 | Columnfsipv6ScopeZoneIndex7 | read-write | current | The zone index for scope 7 on this interface.The index value corresponding to this scope-zone can be known from ipv6ScopeZoneIndex7 |
| 1.3.6.1.4.1.10876.101.1.28.1.2.15.1.9 | Columnfsipv6ScopeZoneIndexOrganizationLocal | read-write | current | The zone index for the organization-local scope on this interface.The index value corresponding to this scope-zone can be known from ipv6ScopeZoneIndexOrganiza… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.15.1.10 | Columnfsipv6ScopeZoneIndex9 | read-write | current | The zone index for scope 9 on this interface.The index value corresponding to this scope-zone can be known from ipv6ScopeZoneIndex9 |
| 1.3.6.1.4.1.10876.101.1.28.1.2.15.1.11 | Columnfsipv6ScopeZoneIndexA | read-write | current | The zone index for scope A on this interface.The index value corresponding to this scope-zone can be known from ipv6ScopeZoneIndexA |
| 1.3.6.1.4.1.10876.101.1.28.1.2.15.1.12 | Columnfsipv6ScopeZoneIndexB | read-write | current | The zone index for scope B on this interface.The index value corresponding to this scope-zone can be known from ipv6ScopeZoneIndexB |
| 1.3.6.1.4.1.10876.101.1.28.1.2.15.1.13 | Columnfsipv6ScopeZoneIndexC | read-write | current | The zone index for scope C on this interface.The index value corresponding to this scope-zone can be known from ipv6ScopeZoneIndexC |
| 1.3.6.1.4.1.10876.101.1.28.1.2.15.1.14 | Columnfsipv6ScopeZoneIndexD | read-write | current | The zone index for scope D on this interface.The index value corresponding to this scope-zone can be known from ipv6ScopeZoneIndexD |
| 1.3.6.1.4.1.10876.101.1.28.1.2.15.1.15 | Columnfsipv6ScopeZoneIndexE | read-write | current | The zone index for scope E on this interface. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.15.1.16 | Columnfsipv6IfScopeZoneCreationStatus | read-only | current | Flag to determine if the scope-zone index is configured automatically or by configuration.When an IPv6 interface is created by default the linklocal scope is c… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.15.1.17 | Columnfsipv6IfScopeZoneRowStatus | read-create | current | The rowstatus of the scope-zone index table, used in accordance to creation and deletion of scope-zones.To create a row in this table manager sets this object … |
| 1.3.6.1.4.1.10876.101.1.28.1.2.16 | Tablefsipv6ScopeZoneTable | not-accessible | current | The table is used to map each scope-zone index with the interface to which it has been associated. This table is indeed used while forwarding packets to find o… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.16.1 | Rowfsipv6ScopeZoneEntry | not-accessible | current | An entry in the Scope-Zone Index Member Table.Each entry specifies the interface indices associated with a particular scope-zone index |
| 1.3.6.1.4.1.10876.101.1.28.1.2.16.1.1 | Columnfsipv6ScopeZoneName | not-accessible | current | Displays the scope zone name value(i.e linklocal1, interfacelocal2) for the scope-zone index |
| 1.3.6.1.4.1.10876.101.1.28.1.2.16.1.2 | Columnfsipv6ScopeZoneIndex | read-only | current | A unique value for each scope on an interface. It is recommended that values are assigned contiguously starting from 1. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.16.1.3 | Columnfsipv6ScopeZoneCreationStatus | read-only | current | Flag to determine if the scope-zone index is configured automatically or by configuration.When an IPv6 interface is created by default the linklocal scope is c… |
| 1.3.6.1.4.1.10876.101.1.28.1.2.16.1.4 | Columnfsipv6ScopeZoneInterfaceList | read-only | current | This MIB object displays all the interfaces that are part of/members of this scope-zone index. These interfaces have the corresponding bit set in the octetlist. |
| 1.3.6.1.4.1.10876.101.1.28.1.2.16.1.5 | Columnfsipv6IsDefaultScopeZone | read-write | current | yes- indicates that zone is default zone for the associated scope No - indicates that zone is not the default zone for the associated scope |
| 1.3.6.1.4.1.10876.101.1.28.1.3 | Nodefsipv6Test | |||
| 1.3.6.1.4.1.10876.101.1.28.1.3.1 | ScalarfsIpv6TestRedEntryTime | read-only | current | Time when the node starts entering active state from standby state |
| 1.3.6.1.4.1.10876.101.1.28.1.3.2 | ScalarfsIpv6TestRedExitTime | read-only | current | Time when the node completes entering active state from standby state |
| 1.3.6.1.4.1.10876.101.1.28.2 | Nodefsipv6Icmp | |||
| 1.3.6.1.4.1.10876.101.1.28.2.1 | Scalarfsipv6IcmpInMsgs | read-only | current | The total number of ICMP messages which the entity received. Note that this counter includes all those counted by fsipv6IcmpInErrors. |
| 1.3.6.1.4.1.10876.101.1.28.2.2 | Scalarfsipv6IcmpInErrors | read-only | current | The number of ICMP messages which the entity received but determined as having ICMP-specific errors (bad ICMP checksums, bad length, etc.). |
| 1.3.6.1.4.1.10876.101.1.28.2.3 | Scalarfsipv6IcmpInDestUnreachs | read-only | current | The number of ICMP Destination Unreachable messages received. |
| 1.3.6.1.4.1.10876.101.1.28.2.4 | Scalarfsipv6IcmpInTimeExcds | read-only | current | The number of ICMP Time Exceeded messages received. |
| 1.3.6.1.4.1.10876.101.1.28.2.5 | Scalarfsipv6IcmpInParmProbs | read-only | current | The number of ICMP Parameter Problem messages received. |
| 1.3.6.1.4.1.10876.101.1.28.2.6 | Scalarfsipv6IcmpInPktTooBigs | read-only | current | The number of ICMP Packet Too Big messages received. |
| 1.3.6.1.4.1.10876.101.1.28.2.7 | Scalarfsipv6IcmpInEchos | read-only | current | The number of ICMP Echo (request) messages received. |
| 1.3.6.1.4.1.10876.101.1.28.2.8 | Scalarfsipv6IcmpInEchoReps | read-only | current | The number of ICMP Echo Reply messages received. |
| 1.3.6.1.4.1.10876.101.1.28.2.9 | Scalarfsipv6IcmpInRouterSolicits | read-only | current | The number of ICMP Router Solicit messages received. |
| 1.3.6.1.4.1.10876.101.1.28.2.10 | Scalarfsipv6IcmpInRouterAdvertisements | read-only | current | The number of ICMP Router Advertisement messages received. |
| 1.3.6.1.4.1.10876.101.1.28.2.11 | Scalarfsipv6IcmpInNeighborSolicits | read-only | current | The number of ICMP Neighbor Solicit messages received. |
| 1.3.6.1.4.1.10876.101.1.28.2.12 | Scalarfsipv6IcmpInNeighborAdvertisements | read-only | current | The number of ICMP Neighbor Advertisement messages received. |
| 1.3.6.1.4.1.10876.101.1.28.2.13 | Scalarfsipv6IcmpInRedirects | read-only | current | The number of Redirect messages received. |
| 1.3.6.1.4.1.10876.101.1.28.2.14 | Scalarfsipv6IcmpInAdminProhib | read-only | current | Number of ICMP destination unreachable/communication administratively prohibited messages received. |
| 1.3.6.1.4.1.10876.101.1.28.2.15 | Scalarfsipv6IcmpOutMsgs | read-only | current | The total number of ICMP messages which this entity attempted to send. Note that this counter includes all those counted by icmpOutErrors. |
| 1.3.6.1.4.1.10876.101.1.28.2.16 | Scalarfsipv6IcmpOutErrors | read-only | current | The number of ICMP messages which this entity did not send due to problems discovered within ICMP such as a lack of buffers. This value should not include erro… |
| 1.3.6.1.4.1.10876.101.1.28.2.17 | Scalarfsipv6IcmpOutDestUnreachs | read-only | current | The number of ICMP Destination Unreachable messages sent. |
| 1.3.6.1.4.1.10876.101.1.28.2.18 | Scalarfsipv6IcmpOutTimeExcds | read-only | current | The number of ICMP Time Exceeded messages sent. |
| 1.3.6.1.4.1.10876.101.1.28.2.19 | Scalarfsipv6IcmpOutParmProbs | read-only | current | The number of ICMP Parameter Problem messages sent. |
| 1.3.6.1.4.1.10876.101.1.28.2.20 | Scalarfsipv6IcmpOutPktTooBigs | read-only | current | The number of ICMP Packet Too Big messages sent. |
| 1.3.6.1.4.1.10876.101.1.28.2.21 | Scalarfsipv6IcmpOutEchos | read-only | current | The number of ICMP Echo (request) messages sent. |
| 1.3.6.1.4.1.10876.101.1.28.2.22 | Scalarfsipv6IcmpOutEchoReps | read-only | current | The number of ICMP Echo Reply messages sent. |
| 1.3.6.1.4.1.10876.101.1.28.2.23 | Scalarfsipv6IcmpOutRouterSolicits | read-only | current | The number of ICMP Router Solicitation messages sent. |
| 1.3.6.1.4.1.10876.101.1.28.2.24 | Scalarfsipv6IcmpOutRouterAdvertisements | read-only | current | The number of ICMP Router Advertisement messages received. |
| 1.3.6.1.4.1.10876.101.1.28.2.25 | Scalarfsipv6IcmpOutNeighborSolicits | read-only | current | The number of ICMP Neighbor Solicitation messages sent. |
| 1.3.6.1.4.1.10876.101.1.28.2.26 | Scalarfsipv6IcmpOutNeighborAdvertisements | read-only | current | The number of ICMP Neighbor Advertisement messages received. |
| 1.3.6.1.4.1.10876.101.1.28.2.27 | Scalarfsipv6IcmpOutRedirects | read-only | current | The number of Redirect messages sent. For a host, this object will always be zero, since hosts do not send redirects. |
| 1.3.6.1.4.1.10876.101.1.28.2.28 | Scalarfsipv6IcmpOutAdminProhib | read-only | current | Number of ICMP destination unreachable/ communication administratively prohibited messages sent. |
| 1.3.6.1.4.1.10876.101.1.28.2.29 | Scalarfsipv6IcmpInBadCode | read-only | current | Number of received ICMP messages having unrecognized type of message |
| 1.3.6.1.4.1.10876.101.1.28.2.30 | Scalarfsipv6IcmpInNARouterFlagSet | read-only | current | The number of ICMP Neighbor Advertisement received with Router Flag Set |
| 1.3.6.1.4.1.10876.101.1.28.2.31 | Scalarfsipv6IcmpInNASolicitedFlagSet | read-only | current | The number of ICMP Neighbor Advertisement received with Solicited Flag Set |
| 1.3.6.1.4.1.10876.101.1.28.2.32 | Scalarfsipv6IcmpInNAOverrideFlagSet | read-only | current | The number of ICMP Neighbor Advertisement received with Override Flag Set |
| 1.3.6.1.4.1.10876.101.1.28.2.33 | Scalarfsipv6IcmpOutNARouterFlagSet | read-only | current | The number of ICMP Neighbor Advertisement sent with Router Flag Set |
| 1.3.6.1.4.1.10876.101.1.28.2.34 | Scalarfsipv6IcmpOutNASolicitedFlagSet | read-only | current | The number of ICMP Neighbor Advertisement sent with Solicited Flag Set |
| 1.3.6.1.4.1.10876.101.1.28.2.35 | Scalarfsipv6IcmpOutNAOverrideFlagSet | read-only | current | The number of ICMP Neighbor Advertisement sent with Override Flag Set |
| 1.3.6.1.4.1.10876.101.1.28.3 | Nodefsipv6Udp | |||
| 1.3.6.1.4.1.10876.101.1.28.3.1 | Nodefsipv6UdpScalars | |||
| 1.3.6.1.4.1.10876.101.1.28.3.1.1 | Scalarfsipv6UdpInDatagrams | read-only | current | The total number of UDP datagrams delivered to UDP users. |
| 1.3.6.1.4.1.10876.101.1.28.3.1.2 | Scalarfsipv6UdpNoPorts | read-only | current | The total number of received UDP datagrams for which there was no application at the destination port. |
| 1.3.6.1.4.1.10876.101.1.28.3.1.3 | Scalarfsipv6UdpInErrors | read-only | current | The number of received UDP datagrams that could not be delivered for reasons other than the lack of an application at the destination port. |
| 1.3.6.1.4.1.10876.101.1.28.3.1.4 | Scalarfsipv6UdpOutDatagrams | read-only | current | The total number of UDP datagrams sent from this entity. |
| 1.3.6.1.4.1.10876.101.1.28.5 | Nodefsipv6Tunnel | |||
| 1.3.6.1.4.1.10876.101.1.28.6 | Nodefsipv6Route | |||
| 1.3.6.1.4.1.10876.101.1.28.6.1 | Tablefsipv6RouteTable | not-accessible | current | This table contains dynamic routes that are learnt through dynamic routing protocol as well as local routes derived from configured address prefixes and static… |
| 1.3.6.1.4.1.10876.101.1.28.6.1.1 | Rowfsipv6RouteEntry | not-accessible | current | An entry in the IPv6 Routing Table. An entry can be created by means of the routing protocol, derived from configured address prefixes as well as statically co… |
| 1.3.6.1.4.1.10876.101.1.28.6.1.1.1 | Columnfsipv6RouteDest | not-accessible | current | The destination IPv6 address of this route. This object will not take a Link-Local or Multicast address value. |
| 1.3.6.1.4.1.10876.101.1.28.6.1.1.2 | Columnfsipv6RoutePfxLength | not-accessible | current | Indicates the prefix length of the destination address. |
| 1.3.6.1.4.1.10876.101.1.28.6.1.1.3 | Columnfsipv6RouteProtocol | not-accessible | current | The routing mechanism via which this route was learned. If it has value local(2), it indicates this route was derived from a configured address prefix. |
| 1.3.6.1.4.1.10876.101.1.28.6.1.1.4 | Columnfsipv6RouteNextHop | not-accessible | current | Next hop IPv6 Address for this route. For direct routes it has the value ::0. |
| 1.3.6.1.4.1.10876.101.1.28.6.1.1.5 | Columnfsipv6RouteIfIndex | read-write | current | The index value which uniquely identifies the interface through which the next hop of this route should be reached. The interface identified by a particular va… |
| 1.3.6.1.4.1.10876.101.1.28.6.1.1.6 | Columnfsipv6RouteMetric | read-write | current | The routing metric associated with this route. |
| 1.3.6.1.4.1.10876.101.1.28.6.1.1.7 | Columnfsipv6RouteType | read-write | current | The type of route. Note that 'local(3)' refers to a route for which the next hop is the final destination; 'remote(4)' refers to a route for which the next hop… |
| 1.3.6.1.4.1.10876.101.1.28.6.1.1.8 | Columnfsipv6RouteTag | read-write | current | This object specifies whether this route is an internal or external route. Value 0 represent routes are internal to the routing domain and Value > 0 represent … |
| 1.3.6.1.4.1.10876.101.1.28.6.1.1.9 | Columnfsipv6RouteAge | read-only | current | The number of seconds since this route was last updated or otherwise determined to be correct. For statically configured routes and locally derived routes, thi… |
| 1.3.6.1.4.1.10876.101.1.28.6.1.1.10 | Columnfsipv6RouteAdminStatus | read-create | current | Administrative Status of the route. This object is used to create or delete the route entry. The fsipv6RouteIfIndex needs to be set, before the route entry is … |
| 1.3.6.1.4.1.10876.101.1.28.6.1.1.11 | Columnfsipv6RouteAddrType | read-write | current | Indicates whether the destination address in the route entry is unicast or anycast. |
| 1.3.6.1.4.1.10876.101.1.28.6.1.1.12 | Columnfsipv6RouteHwStatus | read-only | current | Indicates whether the route entry is either present or not present in the hardware. |
| 1.3.6.1.4.1.10876.101.1.28.6.2 | Tablefsipv6PrefTable | not-accessible | current | The IPv6 Preference table contains information on the Preference Value for each supported protocol. |
| 1.3.6.1.4.1.10876.101.1.28.6.2.1 | Rowfsipv6PrefEntry | not-accessible | current | An entry containing objects about a particular protocols preference value. |
| 1.3.6.1.4.1.10876.101.1.28.6.2.1.1 | Columnfsipv6Protocol | not-accessible | current | A unique value identifying the protocol whose preference value needs to be processed. |
| 1.3.6.1.4.1.10876.101.1.28.6.2.1.2 | Columnfsipv6Preference | read-write | current | Preference of the route learned by a particular protocol. This value is used while choosing the best path. Lesser the value, highest is the preference. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| InterfaceList | OCTET STRING | current | Each octet within this value specifies a set of eight interfaces, with the first octet specifying router-ports 1 through 8, the second octet specifying router-ports 9 through 16, etc. Within each octet, the most signifi… |