SUPERMICRO-ISS-MIB
334 objects
The MIB for ISS.
Imported Objects
| IF-MIB | InterfaceIndex |
| INET-ADDRESS-MIB | InetAddress InetAddressType |
| SNMPv2-SMI | Counter32 enterprises Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString MacAddress RowStatus StorageType TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.10876.101.1.81 | Identityiss | The MIB for ISS. | ||
| 1.3.6.1.4.1.10876.101.1.81.0 | NodeissNotifications | |||
| 1.3.6.1.4.1.10876.101.1.81.0.1 | NotificationissTrapConfigRestore | current | This trap signifies the successful restoration of the saved configuration | |
| 1.3.6.1.4.1.10876.101.1.81.0.2 | NotificationissMsrUpdateEventFail | current | An MsrUpdateEventFail notification is sent when there is some failure in configuration change event received from SNMP Agent. issMsrFailedOid indicates the OID… | |
| 1.3.6.1.4.1.10876.101.1.81.0.3 | NotificationissAuditTrapMessage | current | This trap notifies the erros on Audit file. | |
| 1.3.6.1.4.1.10876.101.1.81.0.4 | NotificationissTrapTemperature | current | This notification is sent when the current temperature rises above or drops below the threshold. | |
| 1.3.6.1.4.1.10876.101.1.81.0.5 | NotificationissTrapCPUThreshold | current | This notification is sent when CPU load exceeds the threshold value | |
| 1.3.6.1.4.1.10876.101.1.81.0.6 | NotificationissTrapPowerSupply | current | This notification is sent when the current voltage drops below or exceeds the threshold value | |
| 1.3.6.1.4.1.10876.101.1.81.0.7 | NotificationissTrapRAMUsage | current | This notification is sent when the RAM usage crosses the threshold percentage. | |
| 1.3.6.1.4.1.10876.101.1.81.0.8 | NotificationissTrapFlashUsage | current | This notification is sent when the flash usage crosses the threshold. | |
| 1.3.6.1.4.1.10876.101.1.81.0.9 | NotificationissTrapFanStatus | current | This notification is sent when the fan status is changed from down state to up state or vice versa. | |
| 1.3.6.1.4.1.10876.101.1.81.0.10 | NotificationissLogTrapMessage | current | This trap notifies the erros on System Log file. | |
| 1.3.6.1.4.1.10876.101.1.81.1 | NodeissSystem | |||
| 1.3.6.1.4.1.10876.101.1.81.1.1 | ScalarissSwitchName | read-write | current | System name used for identification of the device. |
| 1.3.6.1.4.1.10876.101.1.81.1.2 | ScalarissHardwareVersion | read-only | current | Version number of the Hardware. |
| 1.3.6.1.4.1.10876.101.1.81.1.3 | ScalarissFirmwareVersion | read-only | current | Version number of the Firmware. |
| 1.3.6.1.4.1.10876.101.1.81.1.4 | ScalarissDefaultIpAddrCfgMode | read-write | current | Specifies the means by which the default interface in the device gets the IP address. If 'manual' mode is selected, the default interface takes the 'issDefault… |
| 1.3.6.1.4.1.10876.101.1.81.1.5 | ScalarissDefaultIpAddr | read-write | current | Default IP Address of the system. This IP address, if modified, will take effect only when the configuration is stored & restored. |
| 1.3.6.1.4.1.10876.101.1.81.1.6 | ScalarissDefaultIpSubnetMask | read-write | current | IP subnet mask for the default IP address. This subnet mask, if modified, will take effect only when the configuration is stored & restored. |
| 1.3.6.1.4.1.10876.101.1.81.1.7 | ScalarissEffectiveIpAddr | read-only | deprecated | Effective IP address of the switch to be used for contacting through SNMP interface or web interface. This IP address will be same as the default IP address if… |
| 1.3.6.1.4.1.10876.101.1.81.1.8 | ScalarissDefaultInterface | read-write | current | Name of the default interface that can be used for communicating with the system for configuration through SNMP or WebInterface. The default interface, if modi… |
| 1.3.6.1.4.1.10876.101.1.81.1.9 | ScalarissRestart | read-write | current | This object allows the user to restart the Switch (i.e)the entire switch will operationally go down and start again. Setting a value of 'true' causes the switc… |
| 1.3.6.1.4.1.10876.101.1.81.1.10 | ScalarissConfigSaveOption | read-write | current | Specifies whether the configurations of the switch has to be saved or not. The value 'noSave' specifies that the configurations need not be saved. The value 'f… |
| 1.3.6.1.4.1.10876.101.1.81.1.11 | ScalarissConfigSaveIpAddr | read-write | deprecated | IP Address of the remote system to which the switch configurations have to be saved. This object is valid only if 'issConfigSaveOption' is chosen to be 'remote… |
| 1.3.6.1.4.1.10876.101.1.81.1.12 | ScalarissConfigSaveFileName | read-write | current | Name of the file in which the switch configurations are to be saved. This object is valid only if 'issConfigSaveOption' is chosen to be 'flashSave' or 'remoteS… |
| 1.3.6.1.4.1.10876.101.1.81.1.13 | ScalarissInitiateConfigSave | read-write | current | When set as 'true' switch configurations save operation is initiated. As soon as the configuration save operation is completed, the value of this object revert… |
| 1.3.6.1.4.1.10876.101.1.81.1.14 | ScalarissConfigSaveStatus | read-only | current | Status of configuration save operation. |
| 1.3.6.1.4.1.10876.101.1.81.1.15 | ScalarissConfigRestoreOption | read-write | current | Specifies whether the switch configurations have to be restored or not. The value 'noRestore' specifies that the switch configurations need not be restored whe… |
| 1.3.6.1.4.1.10876.101.1.81.1.16 | ScalarissConfigRestoreIpAddr | read-write | deprecated | IP Address of the remote system from where the switch configurations have to be downloaded to the 'Startup Configuration File' in the flash. This object is dep… |
| 1.3.6.1.4.1.10876.101.1.81.1.17 | ScalarissConfigRestoreFileName | read-write | current | The configuration file name in the remote system which has to be downloaded to the 'Startup Configuration File' in the flash. |
| 1.3.6.1.4.1.10876.101.1.81.1.18 | ScalarissInitiateConfigRestore | read-write | current | When set as 'true', the switch configurations will be downloaded from the specified remote system to the 'Startup Configuration File' in the flash. As soon as … |
| 1.3.6.1.4.1.10876.101.1.81.1.19 | ScalarissConfigRestoreStatus | read-only | current | The status of the switch configuration restore operation. |
| 1.3.6.1.4.1.10876.101.1.81.1.20 | ScalarissDlImageFromIp | read-write | deprecated | The Ip Address of machine from where the image has to be downloaded. This object is deprecated, as this object supports only IPv4, this IP can be set through i… |
| 1.3.6.1.4.1.10876.101.1.81.1.21 | ScalarissDlImageName | read-write | current | The image name which is to be downloaded to the switch. |
| 1.3.6.1.4.1.10876.101.1.81.1.22 | ScalarissInitiateDlImage | read-write | current | Initiates the Image Download operation. |
| 1.3.6.1.4.1.10876.101.1.81.1.23 | ScalarissLoggingOption | read-write | current | The Logging option specifying whether the logging is to be done at console or to a file(system buffer) in the system. Flash specifies the logging of traces int… |
| 1.3.6.1.4.1.10876.101.1.81.1.24 | ScalarissUploadLogFileToIp | read-write | deprecated | The Ip Address of machine to which the log file is to be uploaded. This object is deprecated, as this object supports only IPv4, this IP can be set through iss… |
| 1.3.6.1.4.1.10876.101.1.81.1.25 | ScalarissLogFileName | read-write | current | The file name to be used for uploading the logs from 'file' to the remote system. This object is useful only when the 'LogOption' is chosen as 'file'. |
| 1.3.6.1.4.1.10876.101.1.81.1.26 | ScalarissInitiateUlLogFile | read-write | current | Initiates uploading of Log File to the specified IP address in 'issUploadLogFileToIp'. The logs will be uploaded in the specified 'issLogFileName'. |
| 1.3.6.1.4.1.10876.101.1.81.1.27 | ScalarissRemoteSaveStatus | read-only | current | Status of remote save operation. The remote save operation could be a a) configuration file save to remote system b) log file upload to remote system. |
| 1.3.6.1.4.1.10876.101.1.81.1.28 | ScalarissDownloadStatus | read-only | current | The status of the Image download operation to the switch. |
| 1.3.6.1.4.1.10876.101.1.81.1.29 | ScalarissSysContact | read-write | deprecated | The textual identification of the contact person for this managed node, together with information on how to contact this person. If no contact information is k… |
| 1.3.6.1.4.1.10876.101.1.81.1.30 | ScalarissSysLocation | read-write | deprecated | The physical location of this node (e.g., `telephone closet, 3rd floor'). If the location is unknown, the value is the zero-length string. |
| 1.3.6.1.4.1.10876.101.1.81.1.31 | ScalarissLoginAuthentication | read-write | current | Configures the mechanism by which the user login has to be authenticated for accessing the GUI to manage the switch. Authentication is done either locally or i… |
| 1.3.6.1.4.1.10876.101.1.81.1.32 | ScalarissSwitchBaseMacAddress | read-write | current | Ethernet address (base address) of the Switch. This base Mac Address, if modified, will take effect only when the Switch is restarted. |
| 1.3.6.1.4.1.10876.101.1.81.1.33 | ScalarissOOBInterface | read-only | current | Indicates wheteher OOB Interface Exists in the System |
| 1.3.6.1.4.1.10876.101.1.81.1.34 | ScalarissSwitchDate | read-write | current | The date is configured in the switch in the format, Hours:Minutes:Seconds Day Month Year e.g 19:10:31 11 08 2005 01-12 Month - beginning from January to Decemb… |
| 1.3.6.1.4.1.10876.101.1.81.1.35 | ScalarissNoCliConsole | read-write | current | Indicates whether the CLI console prompt will be made available to the user for the session through serial console. When set to TRUE CLI prompt will be availab… |
| 1.3.6.1.4.1.10876.101.1.81.1.36 | ScalarissDefaultIpAddrAllocProtocol | read-write | current | Specifies the protocol to be used to obtain IP address for this interface. This object is valid only when issDefaultIpAddrCfgMode is set to dynamic (2). Curren… |
| 1.3.6.1.4.1.10876.101.1.81.1.37 | ScalarissHttpPort | read-write | current | The port to be used by the hosts/PC to configure ISS using the Web Interface The HTTP server must be disabled before this configuration is done |
| 1.3.6.1.4.1.10876.101.1.81.1.38 | ScalarissHttpStatus | read-write | current | This object is for enabling or disabling HTTP in the system. |
| 1.3.6.1.4.1.10876.101.1.81.1.39 | ScalarissConfigRestoreFileVersion | read-only | current | Config Restoration file version. This version will be compared in each reboot against version stored in restoration file. Restoration will occur only if the fi… |
| 1.3.6.1.4.1.10876.101.1.81.1.40 | ScalarissDefaultRmIfName | read-write | current | Name of the default RM interface that can be used for communication between the Active and Standby nodes for providing redundancy support.The default RM interf… |
| 1.3.6.1.4.1.10876.101.1.81.1.41 | ScalarissDefaultVlanId | read-write | current | The Default VLAN Identifier to be used at system startup. The VLAN Module creates this vlan as the default vlan. The Default VLAN Identifier, if modified, will… |
| 1.3.6.1.4.1.10876.101.1.81.1.42 | ScalarissNpapiMode | read-write | current | The Mode of NPAPI Processing. It can be 1. Synchronous, 2. Asynchronous. |
| 1.3.6.1.4.1.10876.101.1.81.1.43 | ScalarissConfigAutoSaveTrigger | read-write | current | When set as 'true', automatic save operation is enabled. i.e., every configuration is saved automatically. When set as 'false', automatic save operation is dis… |
| 1.3.6.1.4.1.10876.101.1.81.1.44 | ScalarissConfigIncrSaveFlag | read-write | current | Indicates whether SNMP Update Trigger for Incremental Save shall be generated or not. 'True' value implies that the update trigger shall be generated each time… |
| 1.3.6.1.4.1.10876.101.1.81.1.45 | ScalarissConfigRollbackFlag | read-write | current | Indicates whether SNMP Rollback feature is enabled or disabled. 'enabled' value implies that failure in set operation for any varbind will result in rollback o… |
| 1.3.6.1.4.1.10876.101.1.81.1.46 | ScalarissConfigSyncUpOperation | read-write | current | Indicates that sync operation is to be performed. Incremental save OFF: RB tree, incremental file/buffer are not present in the system, sync operation is not a… |
| 1.3.6.1.4.1.10876.101.1.81.1.47 | ScalarissFrontPanelPortCount | read-write | current | The object defines the number of physical ports configured in a device for the purpose of switching/routing. The value of the object should not exceed system d… |
| 1.3.6.1.4.1.10876.101.1.81.1.48 | ScalarissAuditLogStatus | read-write | current | To Enable or disable Audit Logging |
| 1.3.6.1.4.1.10876.101.1.81.1.49 | ScalarissAuditLogFileName | read-write | current | The name of the file to which Audit log is saved |
| 1.3.6.1.4.1.10876.101.1.81.1.50 | ScalarissAuditLogFileSize | read-write | current | This is the maximum file size in bytes of the config.txt file |
| 1.3.6.1.4.1.10876.101.1.81.1.51 | ScalarissAuditLogReset | read-write | current | Setting this to true ,erases the contents in configs.txt fileand start logging |
| 1.3.6.1.4.1.10876.101.1.81.1.52 | ScalarissAuditLogRemoteIpAddr | read-write | deprecated | IP Address of the remote system to which the Audit file has to be transfered from flash. This object is deprecated, as this object supports only IPv4, this IP … |
| 1.3.6.1.4.1.10876.101.1.81.1.53 | ScalarissAuditLogInitiateTransfer | read-write | current | Setting this will start transfer of the file indicated by issAuditLogFileName from flash to remote Address mentioned by issAuditLogRemoteIpAddr |
| 1.3.6.1.4.1.10876.101.1.81.1.54 | ScalarissAuditTransferFileName | read-write | current | The name of the file to be retrieved from flash |
| 1.3.6.1.4.1.10876.101.1.81.1.55 | ScalarissDownLoadTransferMode | read-write | current | To select the Transfer mode for downloading image. |
| 1.3.6.1.4.1.10876.101.1.81.1.56 | ScalarissDownLoadUserName | read-write | current | This mib-object is used for setting User name required for downloading image. When Transfer Mode is selected as tftp, contents of this mib-object becomes irrel… |
| 1.3.6.1.4.1.10876.101.1.81.1.57 | ScalarissDownLoadPassword | read-write | current | This mib-object is used for setting password required for downloading image. When Transfer Mode is selected as tftp, contents of this mib-object becomes irrele… |
| 1.3.6.1.4.1.10876.101.1.81.1.58 | ScalarissUploadLogTransferMode | read-write | current | To select the Transfer mode for uploading log file. |
| 1.3.6.1.4.1.10876.101.1.81.1.59 | ScalarissUploadLogUserName | read-write | current | This mib-object is used for setting User name required for uploading log file. When Transfer Mode is selected as tftp, contents of this mib-object becomes irre… |
| 1.3.6.1.4.1.10876.101.1.81.1.60 | ScalarissUploadLogPasswd | read-write | current | This mib-object is used for setting password required for uploading log file. When Transfer Mode is selected as tftp, contents of this mib-object becomes irrel… |
| 1.3.6.1.4.1.10876.101.1.81.1.61 | ScalarissConfigSaveTransferMode | read-write | current | To select the Transfer mode for saving the configurations on to a remote system. Contents of this mib is relevant only when issConfigSaveOption is remote save. |
| 1.3.6.1.4.1.10876.101.1.81.1.62 | ScalarissConfigSaveUserName | read-write | current | This mib-object is used for setting User name required for saving configurations onto a remote site. Contents of this mib is relevant only when issConfigSaveOp… |
| 1.3.6.1.4.1.10876.101.1.81.1.63 | ScalarissConfigSavePassword | read-write | current | This mib-object is used for setting Password required for saving configurations onto a remote site. Contents of this mib is relevant only when the value of iss… |
| 1.3.6.1.4.1.10876.101.1.81.1.64 | ScalarissSwitchMinThresholdTemperature | read-write | current | Indicates the minimum threshold temperature of the switch in celsius. When the current temperature drops below the threshold, an SNMP trap with maximum severit… |
| 1.3.6.1.4.1.10876.101.1.81.1.65 | ScalarissSwitchMaxThresholdTemperature | read-write | current | Indicates the maximum threshold temperature of the switch in celsius. When the current temperature rises above the threshold, an SNMP trap with maximum severit… |
| 1.3.6.1.4.1.10876.101.1.81.1.66 | ScalarissSwitchCurrentTemperature | read-only | current | Indicates the current temperature of the switch in celsius. |
| 1.3.6.1.4.1.10876.101.1.81.1.67 | ScalarissSwitchMaxCPUThreshold | read-write | current | Indicates the maximum CPU usage of the switch in percentage. When CPU load exceeds the threshold value, an SNMP trap with maximum severity will be sent to the … |
| 1.3.6.1.4.1.10876.101.1.81.1.68 | ScalarissSwitchCurrentCPUThreshold | read-only | current | Indicates the current CPU threshold of the switch in percentage |
| 1.3.6.1.4.1.10876.101.1.81.1.69 | ScalarissSwitchPowerSurge | read-write | current | Indicates the maximum power supply of the switch in volts. When the current voltage exceeds the threshold value, an SNMP trap with maximum severity will be sen… |
| 1.3.6.1.4.1.10876.101.1.81.1.70 | ScalarissSwitchPowerFailure | read-write | current | Indicates the minimum power supply of the switch in volts. When the current voltage drops below the threshold value, an SNMP trap with maximum severity will be… |
| 1.3.6.1.4.1.10876.101.1.81.1.71 | ScalarissSwitchCurrentPowerSupply | read-only | current | Indicates the current power supply in volts. |
| 1.3.6.1.4.1.10876.101.1.81.1.72 | ScalarissSwitchMaxRAMUsage | read-write | current | Indicates the maximum RAM usage of the switch in percentage. When the RAM usage crosses the threshold percentage an SNMP trap with maximum severity will be sen… |
| 1.3.6.1.4.1.10876.101.1.81.1.73 | ScalarissSwitchCurrentRAMUsage | read-only | current | Indicates the current RAM usage of the switch in percentage |
| 1.3.6.1.4.1.10876.101.1.81.1.74 | ScalarissSwitchMaxFlashUsage | read-write | current | Indicates the maximum flash usage of the switch in percentage. When the flash usage crosses the threshold percentage an SNMP trap with maximum severity will be… |
| 1.3.6.1.4.1.10876.101.1.81.1.75 | ScalarissSwitchCurrentFlashUsage | read-only | current | Indicates the current flash usage of the switch in percentage |
| 1.3.6.1.4.1.10876.101.1.81.1.76 | ScalarissConfigRestoreFileFormatVersion | read-only | current | Config Save Restoration file format Version.This issConfigRestoreFile FormatVersion value will be compared in each reboot against file format version value sto… |
| 1.3.6.1.4.1.10876.101.1.81.1.77 | ScalarissDebugOption | read-write | current | This object stores the trace option string input given by the user. To enable particular trace the user has to enter the corresponding string(given below) assi… |
| 1.3.6.1.4.1.10876.101.1.81.1.78 | ScalarissConfigDefaultValueSaveOption | read-write | current | Indicates whether default values needs to be saved or not when incremental save option is true.'enabled' value implies, MSR stores default values also when Inc… |
| 1.3.6.1.4.1.10876.101.1.81.1.79 | ScalarissConfigSaveIpAddrType | read-write | current | Address type of IP Address of the remote system to which the switch configurations have to be saved. This object is valid only if 'issConfigSaveOption' is chos… |
| 1.3.6.1.4.1.10876.101.1.81.1.80 | ScalarissConfigSaveIpvxAddr | read-write | current | IP Address of the remote system to which the switch configurations have to be saved. This object is valid only if 'issConfigSaveOption' is chosen to be 'remote… |
| 1.3.6.1.4.1.10876.101.1.81.1.81 | ScalarissConfigRestoreIpAddrType | read-write | current | IP Address type of the remote system from where the switch configurations have to be downloaded to the 'Startup Configuration File' in the flash. |
| 1.3.6.1.4.1.10876.101.1.81.1.82 | ScalarissConfigRestoreIpvxAddr | read-write | current | IP Address of the remote system from where the switch configurations have to be downloaded to the 'Startup Configuration File' in the flash. |
| 1.3.6.1.4.1.10876.101.1.81.1.83 | ScalarissDlImageFromIpAddrType | read-write | current | Ip Address type of machine from where the image has to be downloaded. |
| 1.3.6.1.4.1.10876.101.1.81.1.84 | ScalarissDlImageFromIpvx | read-write | current | The Ip Address of machine from where the image has to be downloaded. |
| 1.3.6.1.4.1.10876.101.1.81.1.85 | ScalarissUploadLogFileToIpAddrType | read-write | current | Ip Address Type of machine to which the log file is to be uploaded. |
| 1.3.6.1.4.1.10876.101.1.81.1.86 | ScalarissUploadLogFileToIpvx | read-write | current | The Ip Address of machine to which the log file is to be uploaded. |
| 1.3.6.1.4.1.10876.101.1.81.1.87 | ScalarissAuditLogRemoteIpAddrType | read-write | current | IP Address Type of the remote system to which the Audit file has to be transfered from flash. |
| 1.3.6.1.4.1.10876.101.1.81.1.88 | ScalarissAuditLogRemoteIpvxAddr | read-write | current | IP Address of the remote system to which the Audit file has to be transfered from flash. |
| 1.3.6.1.4.1.10876.101.1.81.1.89 | ScalarissSystemTimerSpeed | read-write | current | Configures the system timer speed. This is for testing purpose. Value - 1 enables the timer to run in real time speed. Values from (2 - 1000), enables the time… |
| 1.3.6.1.4.1.10876.101.1.81.1.90 | ScalarissMgmtInterfaceRouting | read-write | current | Enables / Disables Routing over the Management Interface. This object can be configured only if the Management Port is used for IP Access. |
| 1.3.6.1.4.1.10876.101.1.81.1.91 | ScalarissMacLearnRateLimit | read-write | current | Maximum number of unicast dynamic MAC (L2) entries hardware can learn in the system, in a configured time interval 'issMacLearnRateLimitInterval'. In next subs… |
| 1.3.6.1.4.1.10876.101.1.81.1.92 | ScalarissMacLearnRateLimitInterval | read-write | current | Number of MAC entries,'issMacLearnRateLimit' that can be learnt in the system in this configured time interval. Any changed timer interval value will take effe… |
| 1.3.6.1.4.1.10876.101.1.81.1.93 | ScalarissVrfUnqMacFlag | read-write | current | Unique mac address can be assigned to each virtual router by enabling this flag. Configuring this object value will result in updation to issnvram.file. The co… |
| 1.3.6.1.4.1.10876.101.1.81.1.94 | ScalarissLoginAttempts | read-write | current | Number of times a user may be allowed to login using wrong password in the login prompt. |
| 1.3.6.1.4.1.10876.101.1.81.1.95 | ScalarissLoginLockTime | read-write | current | Time in seconds a user is blocked following unsuccessful logins. |
| 1.3.6.1.4.1.10876.101.1.81.1.96 | ScalarissAuditLogSizeThreshold | read-write | current | This is the threshold value of the Log storage space with respect to the maximum Log Storage Space. It is entered as a percentage value. |
| 1.3.6.1.4.1.10876.101.1.81.1.97 | ScalarissTelnetStatus | read-write | current | This object is for enabling or disabling the TELNET in the system. Set operation of enable will move this object to the enableInProgress first then to the enab… |
| 1.3.6.1.4.1.10876.101.1.81.1.98 | ScalarissWebSessionTimeOut | read-write | current | Set the Web Session Time Out Value in Seconds |
| 1.3.6.1.4.1.10876.101.1.81.1.99 | ScalarissWebSessionMaxUsers | read-write | current | Set the maximum number of web sessions |
| 1.3.6.1.4.1.10876.101.1.81.1.100 | ScalarissHeartBeatMode | read-write | current | The object is for setting the method for Redundancy manager election mechanism, it can be internal election logic or it can be a external logic. When this obje… |
| 1.3.6.1.4.1.10876.101.1.81.1.101 | ScalarissRmRType | read-write | current | The object is for setting the type of the Redundancy manager, it can be Hot or Cold. When this object is set to be cold, whenever there is node state transitio… |
| 1.3.6.1.4.1.10876.101.1.81.1.102 | ScalarissRmDType | read-write | current | This object specifies the type of the dataplane/hardware, it can be a shared dataplane or a separate dataplane. When this object is set to be shared, standby c… |
| 1.3.6.1.4.1.10876.101.1.81.1.103 | ScalarissClearConfig | read-write | current | When the object is set to TRUE, configurations will be cleared and default configurations will be restored. The value will be reset to FALSE again. |
| 1.3.6.1.4.1.10876.101.1.81.1.104 | ScalarissClearConfigFileName | read-write | current | This is the name of the file, which contains the default configurations to be restored once configurations are cleared. This is optional. When this file name i… |
| 1.3.6.1.4.1.10876.101.1.81.1.105 | ScalarissTelnetClientStatus | read-write | current | This object is for enabling or disabling the TELNET client functionality in the system. Set operation of enable will allow to establish new Telnet client sessi… |
| 1.3.6.1.4.1.10876.101.1.81.1.106 | ScalarissSshClientStatus | read-write | current | This object is for enabling or disabling the SSH client functionality in the system. Set operation of enable will allow to establish new SSH client sessions. S… |
| 1.3.6.1.4.1.10876.101.1.81.1.107 | ScalarissActiveTelnetClientSessions | read-only | current | Specifies the number of active Telnet client sessions running |
| 1.3.6.1.4.1.10876.101.1.81.1.108 | ScalarissActiveSshClientSessions | read-only | current | Specifies the number of active SSH client sessions running |
| 1.3.6.1.4.1.10876.101.1.81.1.109 | ScalarissLogFileSize | read-write | current | This is the maximum file size in bytes of the log file |
| 1.3.6.1.4.1.10876.101.1.81.1.110 | ScalarissLogReset | read-write | current | Setting this to true ,erases the contents in configs.txt fileand start logging |
| 1.3.6.1.4.1.10876.101.1.81.1.111 | ScalarissLogSizeThreshold | read-write | current | This is the threshold value of the Log storage space with respect to the maximum Log Storage Space. It is entered as a percentage value. |
| 1.3.6.1.4.1.10876.101.1.81.1.112 | ScalarissAutomaticPortCreate | read-write | current | This object is for enabling and disabling automatic port create feature.When set to enabled the ports in will be automatically created in RSTP module when it i… |
| 1.3.6.1.4.1.10876.101.1.81.1.113 | ScalarissUlRemoteLogFileName | read-write | current | This object is used to specify the filename/filename with path to which the local file need to be copied in the remote system. This object is useful only when … |
| 1.3.6.1.4.1.10876.101.1.81.1.114 | ScalarissDefaultExecTimeOut | read-write | current | This object is for configuring the default idle time out for ISS Prompt (exec-time out). |
| 1.3.6.1.4.1.10876.101.1.81.1.115 | ScalarissRmStackingInterfaceType | read-write | current | This object is used to specify the type of stacking Interface used for RM communication . Interface can be either an Out of Band port (or) an Inband Ethernet p… |
| 1.3.6.1.4.1.10876.101.1.81.1.116 | ScalarissLoginAuthenticationType | read-write | current | Configures the encrypted type by which the user login has to be authenticated for managing the switch. Authentication is done in the remote side through a TACA… |
| 1.3.6.1.4.1.10876.101.1.81.1.118 | ScalarissLoginAuthenticationServerGroup | read-write | current | This object is used to specify the server group name when doing authentication. If this value is empty, then all TACACS/RADIUS server will be used. |
| 1.3.6.1.4.1.10876.101.1.81.1.119 | ScalarissMgmtInterfaceVlanId | read-write | current | Configure OOB as a untagged or tagged interface. The default vlan 1 menas untagged traffic. |
| 1.3.6.1.4.1.10876.101.1.81.1.120 | ScalarissMemFree | read-only | current | This is the free memory size in kilo bytes of the switch |
| 1.3.6.1.4.1.10876.101.1.81.1.121 | ScalarissCRUTotalBufInUseCount | read-only | current | This is the in use count of CRU(packet) buffer |
| 1.3.6.1.4.1.10876.101.1.81.2 | NodeissConfigControl | |||
| 1.3.6.1.4.1.10876.101.1.81.2.1 | TableissConfigCtrlTable | not-accessible | current | A table to control device features like egress traffic control, stats collection, etc. either for the entire switch or for each interface in the switch. |
| 1.3.6.1.4.1.10876.101.1.81.2.1.1 | RowissConfigCtrlEntry | not-accessible | current | An entry appears in this table for each interface in the system. In addition to that an entry with index '0' is created in this table by default. If 'issConfig… |
| 1.3.6.1.4.1.10876.101.1.81.2.1.1.1 | ColumnissConfigCtrlIndex | not-accessible | current | Interface index of the port for which the configuration in this entry applies. If any configuration is made in this table for the index '0', that configuration… |
| 1.3.6.1.4.1.10876.101.1.81.2.1.1.2 | ColumnissConfigCtrlEgressStatus | read-write | current | Controls the transmission of egress traffic over this interface. This value for entry '0' controls the egress traffic over all interfaces. |
| 1.3.6.1.4.1.10876.101.1.81.2.1.1.3 | ColumnissConfigCtrlStatsCollection | read-write | current | Enables or disables statistics collection for this interface. This value for entry '0' controls the stats collection for all interfaces. |
| 1.3.6.1.4.1.10876.101.1.81.2.1.1.4 | ColumnissConfigCtrlStatus | read-write | current | Speficies the validity of the entry. If the 'Config Control Status' for entry '0' is made 'valid', then global control is chosen in the system. It signifies th… |
| 1.3.6.1.4.1.10876.101.1.81.2.2 | TableissPortCtrlTable | not-accessible | current | A table to control the port specific parameters of the device like speed, duplex mode, etc. |
| 1.3.6.1.4.1.10876.101.1.81.2.2.1 | RowissPortCtrlEntry | not-accessible | current | An entry appears in this table for each interface in the system. Index to the table is the interface index of the port. |
| 1.3.6.1.4.1.10876.101.1.81.2.2.1.1 | ColumnissPortCtrlIndex | not-accessible | current | Interface index of the port for which the configuration in this entry applies. |
| 1.3.6.1.4.1.10876.101.1.81.2.2.1.2 | ColumnissPortCtrlMode | read-write | current | Speficies the mode in which the speed, duplex modes and flow control of the interface is determined. If set as 'auto', the hardware senses speed and negotiates… |
| 1.3.6.1.4.1.10876.101.1.81.2.2.1.3 | ColumnissPortCtrlDuplex | read-write | current | Configures interface data transfer mode as full-duplex or half-duplex. This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'Por… |
| 1.3.6.1.4.1.10876.101.1.81.2.2.1.4 | ColumnissPortCtrlSpeed | read-write | current | Configures interface speed. This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it obtains the value … |
| 1.3.6.1.4.1.10876.101.1.81.2.2.1.5 | ColumnissPortCtrlFlowControl | read-write | deprecated | Enables / disables flow control for the interface. This object be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it… |
| 1.3.6.1.4.1.10876.101.1.81.2.2.1.6 | ColumnissPortCtrlRenegotiate | read-write | current | When configured as 'true', restarts autonegotiation on the interface. Once autonegotiation is restarted, the value of this object reverts to 'false'. |
| 1.3.6.1.4.1.10876.101.1.81.2.2.1.7 | ColumnissPortCtrlMaxMacAddr | read-write | current | Specifies the maximum number of new MAC addresses that can be learnt over the interface. |
| 1.3.6.1.4.1.10876.101.1.81.2.2.1.8 | ColumnissPortCtrlMaxMacAction | read-write | current | Specifies the action to be taken when the maximum number of new MAC addresses that can be learnt over the interface is exceeded. If the action is 'drop', the p… |
| 1.3.6.1.4.1.10876.101.1.81.2.2.1.9 | ColumnissPortHOLBlockPrevention | read-write | current | Enables or disables Head-Of-Line Blocking prevention on a port. |
| 1.3.6.1.4.1.10876.101.1.81.2.2.1.10 | ColumnissPortAutoNegAdvtCapBits | read-write | current | A value uniquely identifies the set of capabilities advertised by the local auto negotiation entity other than the standard capabilities supported by ifMauAuto… |
| 1.3.6.1.4.1.10876.101.1.81.2.2.1.11 | ColumnissPortCpuControlledLearning | read-write | current | Enables or disables the CPU controlled learning on a port. The default behavior is hardware learning. By enabling this object software learning on that particu… |
| 1.3.6.1.4.1.10876.101.1.81.2.2.1.12 | ColumnissPortMdiOrMdixCap | read-write | current | Specifies the port should be in Auto-Mdix mode or Mdi/Mdix. Setting the value to `auto` enables the Auto MDIX in the port - issPortCtrlIndex. This will be effe… |
| 1.3.6.1.4.1.10876.101.1.81.2.2.1.13 | ColumnissPortCtrlFlowControlMaxRate | read-write | current | Configures the maximum rate (kbps) - a high water mark beyond which pause frames will be generated to flow control the ingress traffic. This value should be se… |
| 1.3.6.1.4.1.10876.101.1.81.2.2.1.14 | ColumnissPortCtrlFlowControlMinRate | read-write | current | Configures the minimum rate (kbps) - a low water mark below which pause frames generation will be stopped. This value should be set to a value lesser that of '… |
| 1.3.6.1.4.1.10876.101.1.81.2.3 | TableissPortIsolationTable | not-accessible | current | This table is used to configure the port isolation feature. For a given port, user can configure the list of allowed forwarding/egress ports, where the packets… |
| 1.3.6.1.4.1.10876.101.1.81.2.3.1 | RowissPortIsolationEntry | not-accessible | current | Each etnry in this table gives a ingress port to egress port mapping. |
| 1.3.6.1.4.1.10876.101.1.81.2.3.1.1 | ColumnissPortIsolationIngressPort | not-accessible | current | This object speficies the IfIndex of the ingress port. This port can be a physical or link aggregated port. |
| 1.3.6.1.4.1.10876.101.1.81.2.3.1.2 | ColumnissPortIsolationInVlanId | not-accessible | current | If this object value is non-zero, then the port isolation rule is applied for all packets received on the given ingress port. Otherwise the rule is applied for… |
| 1.3.6.1.4.1.10876.101.1.81.2.3.1.3 | ColumnissPortIsolationEgressPort | not-accessible | current | This object specifies one of the allowed egress ports for the given ingress port identified by the first index for this row. This port can be either a physical… |
| 1.3.6.1.4.1.10876.101.1.81.2.3.1.4 | ColumnissPortIsolationStorageType | read-only | current | Indicates the storage type of this entry. Only 'volatile' and 'nonVolatile' values are allowed for this object. 'readOnly', 'permenant' and 'other' values are … |
| 1.3.6.1.4.1.10876.101.1.81.2.3.1.5 | ColumnissPortIsolationRowStatus | read-create | current | Denotes the Row Status for port isolation table entry. Only 'CreateAndGo' and 'destroy' values are allowed for this object. 'CreateAndWait' and 'notInService' … |
| 1.3.6.1.4.1.10876.101.1.81.2.4 | TableissSplitModeTable | not-accessible | current | A table to control the port split mode of the device |
| 1.3.6.1.4.1.10876.101.1.81.2.4.1 | RowissSplitModeEntry | not-accessible | current | An entry appears in this table for each interface in the system. Index to the table is the interface index of the port. |
| 1.3.6.1.4.1.10876.101.1.81.2.4.1.1 | ColumnissSplitModeIndex | not-accessible | current | Interface index of the port for which the configuration in this entry applies. |
| 1.3.6.1.4.1.10876.101.1.81.2.4.1.2 | ColumnissSplitModeValue | read-write | current | Speficies the setting in which split mode of the interface is determined. If set as 'off', Qx port will be turn on and related Ex ports will be turn off. If se… |
| 1.3.6.1.4.1.10876.101.1.81.3 | NodeissMirror | |||
| 1.3.6.1.4.1.10876.101.1.81.3.1 | ScalarissMirrorStatus | read-write | current | This object is used to enable/disable mirroring feature in hardware. When set to 'disabled (1)', all mirroring configurations will be removed from hardware. Wh… |
| 1.3.6.1.4.1.10876.101.1.81.3.2 | ScalarissMirrorToPort | read-write | current | Specifies the port to which the active mirrored traffic controlled by issMirrorCtrlTable is to be copied. |
| 1.3.6.1.4.1.10876.101.1.81.3.3 | TableissMirrorCtrlTable | not-accessible | current | A table to control mirroring features for each interface in the switch. Parameters in this table are valid only when the 'issMirrorStatus' for the switch is no… |
| 1.3.6.1.4.1.10876.101.1.81.3.3.1 | RowissMirrorCtrlEntry | not-accessible | current | An entry appears in this table for each interface in the system. |
| 1.3.6.1.4.1.10876.101.1.81.3.3.1.1 | ColumnissMirrorCtrlIndex | not-accessible | current | The interface index of the port for which the configuration in this entry applies. |
| 1.3.6.1.4.1.10876.101.1.81.3.3.1.2 | ColumnissMirrorCtrlIngressMirroring | read-write | current | Provides control to enable or disable mirroring of ingress traffic over this interface to the mirrored-to port. |
| 1.3.6.1.4.1.10876.101.1.81.3.3.1.3 | ColumnissMirrorCtrlEgressMirroring | read-write | current | Provides control to enable or disable mirroring of egress traffic over this interface to the mirrored-to port. |
| 1.3.6.1.4.1.10876.101.1.81.3.3.1.4 | ColumnissMirrorCtrlStatus | read-write | current | Specifies the validity of the entry. |
| 1.3.6.1.4.1.10876.101.1.81.3.4 | ScalarissMirrorCtrlRemainingSrcRcrds | read-only | current | Specifies the number of source records remaining in the system. Each record can store at least one source information. In case consecutive source id are config… |
| 1.3.6.1.4.1.10876.101.1.81.3.5 | ScalarissMirrorCtrlRemainingDestRcrds | read-only | current | Specifies the number of destination records remaining in the system. Each record can store at least one destination information. In case consecutive destinatio… |
| 1.3.6.1.4.1.10876.101.1.81.3.6 | TableissMirrorCtrlExtnTable | not-accessible | current | This Table is used to configure advanced mirroring features like - Port Based Mirroring: - flow based mirroring - vlan based mirroring Following are the config… |
| 1.3.6.1.4.1.10876.101.1.81.3.6.1 | RowissMirrorCtrlExtnEntry | not-accessible | current | An entry appears in this table for each session in the system. |
| 1.3.6.1.4.1.10876.101.1.81.3.6.1.1 | ColumnissMirrorCtrlExtnSessionIndex | not-accessible | current | The index of the mirroring session for which the configuration in this entry applies. |
| 1.3.6.1.4.1.10876.101.1.81.3.6.1.2 | ColumnissMirrorCtrlExtnMirrType | read-write | current | This object tells the type of mirroring this session supports. This object needs to be set before doing any configuration for a mirroring session |
| 1.3.6.1.4.1.10876.101.1.81.3.6.1.3 | ColumnissMirrorCtrlExtnRSpanStatus | read-write | current | This object indicates session is enabled or disabled for Remote monitoring. If set as 'source-rspan-vlanid' indicates that the session is enabled for Remote mo… |
| 1.3.6.1.4.1.10876.101.1.81.3.6.1.4 | ColumnissMirrorCtrlExtnRSpanVlanId | read-write | current | Vlan Id used for Remote monitoring for this session. If issMirrorCtrlExtnRSpanStatus is set to disabled, then this object will have an invalid value (zero) |
| 1.3.6.1.4.1.10876.101.1.81.3.6.1.5 | ColumnissMirrorCtrlExtnRSpanContext | read-write | current | Specifies the Context Id to which the RSpan Vlan belongs. Value '0' mean this object is not considered for this mirroring session. |
| 1.3.6.1.4.1.10876.101.1.81.3.6.1.6 | ColumnissMirrorCtrlExtnStatus | read-create | current | This object indicates the status of the entry. The entry can be made active only if issMirrorCtrlExtnMirrType is configured and source and destination entries … |
| 1.3.6.1.4.1.10876.101.1.81.3.7 | TableissMirrorCtrlExtnSrcTable | not-accessible | current | A table to configure list of source entities for mirroring sessions |
| 1.3.6.1.4.1.10876.101.1.81.3.7.1 | RowissMirrorCtrlExtnSrcEntry | not-accessible | current | An entry appears in this table for each mirroring session. |
| 1.3.6.1.4.1.10876.101.1.81.3.7.1.1 | ColumnissMirrorCtrlExtnSrcId | not-accessible | current | Specifies the source id which participates in a mirroring session. For Port based mirroring this object can be port IfIndex. To mirror Tunnel and Trunk ports t… |
| 1.3.6.1.4.1.10876.101.1.81.3.7.1.2 | ColumnissMirrorCtrlExtnSrcCfg | read-write | current | This object is used to create/delete a source entry for a session. |
| 1.3.6.1.4.1.10876.101.1.81.3.7.1.3 | ColumnissMirrorCtrlExtnSrcMode | read-write | current | Provides control to set the mode of mirroring. It can be ingress, egress, both or disable. |
| 1.3.6.1.4.1.10876.101.1.81.3.8 | TableissMirrorCtrlExtnSrcVlanTable | not-accessible | current | A table to configure list of vlan source entities for mirroring sessions |
| 1.3.6.1.4.1.10876.101.1.81.3.8.1 | RowissMirrorCtrlExtnSrcVlanEntry | not-accessible | current | An entry appears in this table for each mirroring session. |
| 1.3.6.1.4.1.10876.101.1.81.3.8.1.1 | ColumnissMirrorCtrlExtnSrcVlanContext | not-accessible | current | Specifies the Context Id to which the source entity belongs, this is used in case of specifying vlan as source. Value '-1' mean this object is not considered f… |
| 1.3.6.1.4.1.10876.101.1.81.3.8.1.2 | ColumnissMirrorCtrlExtnSrcVlanId | not-accessible | current | Specifies the Vlan id which participates in a mirroring session. |
| 1.3.6.1.4.1.10876.101.1.81.3.8.1.3 | ColumnissMirrorCtrlExtnSrcVlanCfg | read-write | current | This object is used to create/delete a vlan entry for a session. |
| 1.3.6.1.4.1.10876.101.1.81.3.8.1.4 | ColumnissMirrorCtrlExtnSrcVlanMode | read-write | current | Provides control to set the mode of mirroring. It can be ingerss,Egress or Both. |
| 1.3.6.1.4.1.10876.101.1.81.3.9 | TableissMirrorCtrlExtnDestinationTable | not-accessible | current | A table to configure list of destination entities |
| 1.3.6.1.4.1.10876.101.1.81.3.9.1 | RowissMirrorCtrlExtnDestinationEntry | not-accessible | current | An entry appears in this table for each destination entity in a mirroring session. |
| 1.3.6.1.4.1.10876.101.1.81.3.9.1.1 | ColumnissMirrorCtrlExtnDestination | not-accessible | current | Specifies the destination port id which participates in a mirroring session. |
| 1.3.6.1.4.1.10876.101.1.81.3.9.1.2 | ColumnissMirrorCtrlExtnDestCfg | read-write | current | This object is used to create/delete a destination entry for a session. |
| 1.3.6.1.4.1.10876.101.1.81.4 | NodeissRateControl | |||
| 1.3.6.1.4.1.10876.101.1.81.4.1 | TableissRateCtrlTable | not-accessible | deprecated | A table to control the rate limiting parameters either for the entire switch or for each interface in the switch. This object is deprecated and the correspondi… |
| 1.3.6.1.4.1.10876.101.1.81.4.1.1 | RowissRateCtrlEntry | not-accessible | deprecated | An entry appears in this table for each physical interface in the switch. This object is deprecated and the corresponding functionality is met with issRateCont… |
| 1.3.6.1.4.1.10876.101.1.81.4.1.1.1 | ColumnissRateCtrlIndex | not-accessible | deprecated | The interface index for which the configuration in this entry applies. This object is deprecated and the corresponding functionality is met with issRateControl… |
| 1.3.6.1.4.1.10876.101.1.81.4.1.1.2 | ColumnissRateCtrlDLFLimitValue | read-write | deprecated | Allows to configure the limiting value for the maximum number of dlf packets that can be transmitted per second over this interface. Setting this object to the… |
| 1.3.6.1.4.1.10876.101.1.81.4.1.1.3 | ColumnissRateCtrlBCASTLimitValue | read-write | deprecated | Allows to configure the limiting value for the maximum number of broadcast packets that can be transmitted per second over this interface. Setting this object … |
| 1.3.6.1.4.1.10876.101.1.81.4.1.1.4 | ColumnissRateCtrlMCASTLimitValue | read-write | deprecated | Allows to configure the limiting value for the maximum number of multicast packets that can be transmitted per second over this interface. Setting this object … |
| 1.3.6.1.4.1.10876.101.1.81.4.1.1.5 | ColumnissRateCtrlPortRateLimit | read-write | deprecated | Configures interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed.… |
| 1.3.6.1.4.1.10876.101.1.81.4.1.1.6 | ColumnissRateCtrlPortBurstSize | read-write | deprecated | Configures interface Burst Pkt Rate. (Packet Burst that can be transferred on a port at a particular second) This object's value will take effect on the interf… |
| 1.3.6.1.4.1.10876.101.1.81.5 | NodeissL2Filter | |||
| 1.3.6.1.4.1.10876.101.1.81.5.1 | TableissL2FilterTable | not-accessible | deprecated | A table to configure L2 filter rules in the system. This object is deprecated and the corresponding functionality is met with issL2Filter objects in fsissext.m… |
| 1.3.6.1.4.1.10876.101.1.81.5.1.1 | RowissL2FilterEntry | not-accessible | deprecated | Each entry in this table is a L2 filter rule.Index to the table is the L2 filter number.This object is deprecated and the corresponding functionality is met wi… |
| 1.3.6.1.4.1.10876.101.1.81.5.1.1.1 | ColumnissL2FilterNo | not-accessible | current | L2 Filter rule number. This object is deprecated and the corresponding functionality is met with issL2Filter objects in fsissext.mib. |
| 1.3.6.1.4.1.10876.101.1.81.5.1.1.2 | ColumnissL2FilterPriority | read-write | current | The priority of the L2 filter can be used to decide which filter rule is applicable when Higher value of 'filter priority' implies a higher priority. Usage of … |
| 1.3.6.1.4.1.10876.101.1.81.5.1.1.3 | ColumnissL2FilterEtherType | read-write | deprecated | The value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '0'. When this object is SET with t… |
| 1.3.6.1.4.1.10876.101.1.81.5.1.1.4 | ColumnissL2FilterProtocolType | read-write | deprecated | Specifies the non IP protocol type to be filtered. aarp | amber | dec-spanning | decnet-iv | diagnostic | dsm |etype-6000 | etype-8042 | lat | lavc-sca | mop-c… |
| 1.3.6.1.4.1.10876.101.1.81.5.1.1.5 | ColumnissL2FilterDstMacAddr | read-write | deprecated | Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero which means dont care condition ie) any Dst Mac Add… |
| 1.3.6.1.4.1.10876.101.1.81.5.1.1.6 | ColumnissL2FilterSrcMacAddr | read-write | deprecated | Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero which means dont care condition ie) any Src Mac address This … |
| 1.3.6.1.4.1.10876.101.1.81.5.1.1.7 | ColumnissL2FilterVlanId | read-write | deprecated | Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. A value of '0' means, this object is unused. Configuring… |
| 1.3.6.1.4.1.10876.101.1.81.5.1.1.8 | ColumnissL2FilterInPortList | read-write | deprecated | Specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list. If the In port list is '0', the filter rule is… |
| 1.3.6.1.4.1.10876.101.1.81.5.1.1.9 | ColumnissL2FilterAction | read-write | deprecated | Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding r… |
| 1.3.6.1.4.1.10876.101.1.81.5.1.1.10 | ColumnissL2FilterMatchCount | read-only | deprecated | Number of times this filter is matched. This object is deprecated and the corresponding functionality is met with issL2Filter objects in fsissext.mib. |
| 1.3.6.1.4.1.10876.101.1.81.5.1.1.11 | ColumnissL2FilterStatus | read-create | deprecated | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.10876.101.1.81.5.1.1.12 | ColumnissL2FilterOutPortList | read-write | deprecated | Specifies the complete set of ports over which this filter is applied for packets egress at Ports in this list. If the Out port list is '0', the filter rule is… |
| 1.3.6.1.4.1.10876.101.1.81.5.1.1.13 | ColumnissL2FilterDirection | read-write | deprecated | Specifies the direction of this filter to be applied. By Default the filter will be applied on ingress direction. When the direction of this filter is 'in', It… |
| 1.3.6.1.4.1.10876.101.1.81.6 | NodeissL3Filter | |||
| 1.3.6.1.4.1.10876.101.1.81.6.1 | TableissL3FilterTable | not-accessible | deprecated | A table to configure L3 filter rules in the system. This object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.m… |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1 | RowissL3FilterEntry | not-accessible | deprecated | Each entry in this table is a L3 filter rule. Index to the table is L3 filter number. This object is deprecated and the corresponding functionality is met with… |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.1 | ColumnissL3FilterNo | not-accessible | deprecated | L3 Filter rule number. This object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.mib. |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.2 | ColumnissL3FilterPriority | read-write | deprecated | The priority of the filter can be used to decide which filter rule is applicable when Higher value of 'L3 filter priority' implies a higher priority. Usage of … |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.3 | ColumnissL3FilterProtocol | read-write | deprecated | The type of protocol to be checked against the packet. The default value is 255. If the value is 255, it means that the protocol type can be anything and it wi… |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.4 | ColumnissL3FilterMessageType | read-write | deprecated | The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action s… |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.5 | ColumnissL3FilterMessageCode | read-write | deprecated | The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action s… |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.6 | ColumnissL3FilterDstIpAddr | read-write | deprecated | Destination IP address to be matched with the packet. This object is valid only if the 'issFilterType' is 'l3filter'. This object is deprecated and the corresp… |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.7 | ColumnissL3FilterSrcIpAddr | read-write | deprecated | Source IP address to be matched with the packet. This object is valid only if the 'issFilterType' is 'l3filter' This object is deprecated and the corresponding… |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.8 | ColumnissL3FilterDstIpAddrMask | read-write | deprecated | The IP subnet mask for Destination IP address. This object is valid only if the 'issFilterType' is 'l3filter' This object is deprecated and the corresponding f… |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.9 | ColumnissL3FilterSrcIpAddrMask | read-write | deprecated | The IP subnet mask for Source IP address. This object is valid only if the 'issFilterType' is 'l3filter'. This object is deprecated and the corresponding funct… |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.10 | ColumnissL3FilterMinDstProtPort | read-write | deprecated | The minimum port in the destination port range. Please note these ports are the TCP / UDP ports. This object is deprecated and the corresponding functionality … |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.11 | ColumnissL3FilterMaxDstProtPort | read-write | deprecated | The maximum port in the destination port range. Please note these ports are the TCP / UDP ports. This object is deprecated and the corresponding functionality … |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.12 | ColumnissL3FilterMinSrcProtPort | read-write | deprecated | The minimum port in the source port range. Please note these ports are the TCP / UDP ports. This object is deprecated and the corresponding functionality is me… |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.13 | ColumnissL3FilterMaxSrcProtPort | read-write | deprecated | The maximum port in the source port range. Please note these ports are the TCP / UDP ports. This object is deprecated and the corresponding functionality is me… |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.14 | ColumnissL3FilterInPortList | read-write | deprecated | Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable. If the incoming port list is '0', the filter rule is … |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.15 | ColumnissL3FilterOutPortList | read-write | deprecated | Specifies the complete set of ports over which if the packet goes out, this filter rule will be applicable. If the outgoing port list is '0',the filter rule is… |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.16 | ColumnissL3FilterAckBit | read-create | deprecated | The TCP ACK bit to be checked against the packet. The default value is 'any'(3). It means that ACK bit will not be checked to decide the action. This object is… |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.17 | ColumnissL3FilterRstBit | read-create | deprecated | The TCP RST bit to be checked against the packet. The default value is 'any'(3). It means that RST bit will not be checked to decide the action. This object is… |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.18 | ColumnissL3FilterTos | read-create | deprecated | The IP TOS bit to be checked against the packet. This is a single byte integer of which the last three bits (least significant bits) indicate Delay, Throughput… |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.19 | ColumnissL3FilterDscp | read-create | deprecated | The IP Dscp value to be checked against the packet. A value of '-1' means, the Dscp Field becomes dont care. This object is deprecated and the corresponding fu… |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.20 | ColumnissL3FilterDirection | read-write | deprecated | Specifies the direction of this filter to be applied. By Default the filter will be applied on ingress direction. When the direction of this filter is 'in', It… |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.21 | ColumnissL3FilterAction | read-write | deprecated | Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be sent to the ports in 'out port list'. I… |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.22 | ColumnissL3FilterMatchCount | read-only | deprecated | Number of times this filter is matched. This object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.mib. |
| 1.3.6.1.4.1.10876.101.1.81.6.1.1.23 | ColumnissL3FilterStatus | read-create | deprecated | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.10876.101.1.81.7 | NodeissIpAuthMgr | |||
| 1.3.6.1.4.1.10876.101.1.81.7.1 | TableissIpAuthMgrTable | not-accessible | current | A table to configure IP authorized managers in the system. |
| 1.3.6.1.4.1.10876.101.1.81.7.1.1 | RowissIpAuthMgrEntry | not-accessible | current | Each entry in this table represents rules for particular IP authorized manager. |
| 1.3.6.1.4.1.10876.101.1.81.7.1.1.1 | ColumnissIpAuthMgrIpAddr | not-accessible | current | Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'. |
| 1.3.6.1.4.1.10876.101.1.81.7.1.1.2 | ColumnissIpAuthMgrIpMask | not-accessible | current | Specifies the IP address mask to be applied on issIpAuthMgrIpAddr. Value 0.0.0.0 indicates mask for 'Any Manager'. |
| 1.3.6.1.4.1.10876.101.1.81.7.1.1.3 | ColumnissIpAuthMgrPortList | read-write | current | Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch throug… |
| 1.3.6.1.4.1.10876.101.1.81.7.1.1.4 | ColumnissIpAuthMgrVlanList | read-write | current | Specifies the Vlan's in which the IP authorized manager can reside. By default the manager is allowed to reside in any vlan. If a set of vlans are configured i… |
| 1.3.6.1.4.1.10876.101.1.81.7.1.1.5 | ColumnissIpAuthMgrOOBPort | read-write | current | Specifies whether the authorized manager can access the switch through OOB Port By default the manager is denied access to reside on OOB Interface |
| 1.3.6.1.4.1.10876.101.1.81.7.1.1.6 | ColumnissIpAuthMgrAllowedServices | read-write | current | Specifies the allowed services through which the authorized manager can access the switch. This object takes bit mask values. The services represented by each … |
| 1.3.6.1.4.1.10876.101.1.81.7.1.1.7 | ColumnissIpAuthMgrRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.10876.101.1.81.8 | NodeissExt | |||
| 1.3.6.1.4.1.10876.101.1.81.9 | NodeissL4Switching | |||
| 1.3.6.1.4.1.10876.101.1.81.9.1 | TableissL4SwitchingFilterTable | not-accessible | current | A table to L4 Switching rules in the system. |
| 1.3.6.1.4.1.10876.101.1.81.9.1.1 | RowissL4SwitchingFilterEntry | not-accessible | current | Each entry in this table is a L4 Switching rule. Index to the table is L4 filter number. |
| 1.3.6.1.4.1.10876.101.1.81.9.1.1.1 | ColumnissL4SwitchingFilterNo | not-accessible | current | L4 Switching Filter rule number. |
| 1.3.6.1.4.1.10876.101.1.81.9.1.1.2 | ColumnissL4SwitchingProtocol | read-write | current | The type of protocol to be checked against the packet. The default value is 255. If the value is 255, it means that the protocol type can be anything and it wi… |
| 1.3.6.1.4.1.10876.101.1.81.9.1.1.3 | ColumnissL4SwitchingPortNo | read-write | current | The Layer 4 port no. Please note these ports are the TCP / UDP ports. |
| 1.3.6.1.4.1.10876.101.1.81.9.1.1.4 | ColumnissL4SwitchingCopyToPort | read-write | current | This object is Port to which the packet would be switched |
| 1.3.6.1.4.1.10876.101.1.81.9.1.1.5 | ColumnissL4SwitchingFilterStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.10876.101.1.81.10 | NodeissSystemTrap | |||
| 1.3.6.1.4.1.10876.101.1.81.10.1 | ScalarissMsrFailedOid | accessible-for-notify | current | Indicates the OID for which updation failure has occured at MSR |
| 1.3.6.1.4.1.10876.101.1.81.10.2 | ScalarissMsrFailedValue | accessible-for-notify | current | Indicates the value of corresponding OID for which updation failure has occured at MSR |
| 1.3.6.1.4.1.10876.101.1.81.11 | NodeissAuditTrap | |||
| 1.3.6.1.4.1.10876.101.1.81.11.1 | ScalarissAuditTrapEvent | accessible-for-notify | current | openFailed - Open operation on Audit File failed. writeFailed - Write operation on Audit File failed. sizeExceeded - Audit File Size exceeded. sizeThresholdHit… |
| 1.3.6.1.4.1.10876.101.1.81.11.2 | ScalarissAuditTrapEventTime | accessible-for-notify | current | This object specifies the date and time at which fsAuditTrapEvent was performed. |
| 1.3.6.1.4.1.10876.101.1.81.11.3 | ScalarissAuditTrapFileName | read-only | current | Audit File name in the trap message. |
| 1.3.6.1.4.1.10876.101.1.81.12 | NodeissModule | |||
| 1.3.6.1.4.1.10876.101.1.81.12.1 | TableissModuleTable | not-accessible | current | A table for triggering Graceful shutdown and Start |
| 1.3.6.1.4.1.10876.101.1.81.12.1.1 | RowissModuleEntry | not-accessible | current | Each entry in this table corresponding to one protocol |
| 1.3.6.1.4.1.10876.101.1.81.12.1.1.1 | ColumnissModuleId | not-accessible | current | This object indicates the ID of the protocol. Following IDs are supported. 1. OSPF 2. OSPFV3 3. BGP 4. ISIS 5. RSVPTE 6. LDP |
| 1.3.6.1.4.1.10876.101.1.81.12.1.1.2 | ColumnissModuleSystemControl | read-write | current | This object shuts and starts the process |
| 1.3.6.1.4.1.10876.101.1.81.13 | NodeissSwitchFan | |||
| 1.3.6.1.4.1.10876.101.1.81.13.1 | TableissSwitchFanTable | not-accessible | current | Table containing the Fan information. |
| 1.3.6.1.4.1.10876.101.1.81.13.1.1 | RowissSwitchFanEntry | not-accessible | current | Indicates information related to fan status of the switch. |
| 1.3.6.1.4.1.10876.101.1.81.13.1.1.1 | ColumnissSwitchFanIndex | not-accessible | current | Indicates the fan number in the switch |
| 1.3.6.1.4.1.10876.101.1.81.13.1.1.2 | ColumnissSwitchFanStatus | read-only | current | Indicates the fan status of the switch. |
| 1.3.6.1.4.1.10876.101.1.81.14 | NodeissAclNp | |||
| 1.3.6.1.4.1.10876.101.1.81.14.1 | ScalarissAclProvisionMode | read-write | current | The MIB object issAclProvisionMode is used to configure the mode for provisioning active Filter Rules to the hardware. This object takes values immediate/conso… |
| 1.3.6.1.4.1.10876.101.1.81.14.2 | ScalarissAclTriggerCommit | read-write | current | The MIB object issAclTriggerCommit takes values true(1)/false (0). A SET on this object ( only true is allowed) triggers the programming of active ACL entries … |
| 1.3.6.1.4.1.10876.101.1.81.15 | NodeissAclTrafficControl | |||
| 1.3.6.1.4.1.10876.101.1.81.15.1 | ScalarissAclTrafficSeperationCtrl | read-write | current | This object provides control to administrator, to have system default or user defined ACL/QoS rules to carry control traffic to CPU. system-default: ACL/QoS ru… |
| 1.3.6.1.4.1.10876.101.1.81.16 | NodeissLogTrap | |||
| 1.3.6.1.4.1.10876.101.1.81.16.1 | ScalarissLogTrapEvent | accessible-for-notify | current | openFailed - Open operation on Log File failed. writeFailed - Write operation on Log File failed. sizeExceeded - Log File Size exceeded. sizeThresholdHit - Log… |
| 1.3.6.1.4.1.10876.101.1.81.16.2 | ScalarissLogTrapEventTime | accessible-for-notify | current | This object specifies the date and time at which fsLogTrapEvent was performed. |
| 1.3.6.1.4.1.10876.101.1.81.16.3 | ScalarissLogTrapFileName | read-only | current | Log File name in the trap message. |
| 1.3.6.1.4.1.10876.101.1.81.17 | NodeissHealthCheckGroup | |||
| 1.3.6.1.4.1.10876.101.1.81.17.1 | ScalarissHealthChkStatus | read-only | current | upAndRunning(1), This status indicates that ISS is up and running and carrying out its job smoothly. downNonRecoverableErr(2), This indicates that the health s… |
| 1.3.6.1.4.1.10876.101.1.81.17.2 | ScalarissHealthChkErrorReason | read-only | current | When the MIB object 'issHealthChkStatus' indicates health as down, this object provides the reason for errors encountered. nonRecovTaskInitializationFailure(1)… |
| 1.3.6.1.4.1.10876.101.1.81.17.3 | ScalarissHealthChkMemAllocErrPoolId | read-only | current | This object retrieves the mem-pool identifier for which memory allocation failure was encountered at run-time.This object will get updated when MIB object fsIS… |
| 1.3.6.1.4.1.10876.101.1.81.17.4 | ScalarissHealthChkConfigRestoreStatus | read-only | current | configRestoreSuccess(1), Indicates that configuration restore operation was successfully done. configRestoreFailed(2),Indicates that configuration restoration … |
| 1.3.6.1.4.1.10876.101.1.81.17.5 | ScalarissHealthChkClearCtr | read-write | current | This object clears the counters associated with the following protocols - BGP, OSPFv2, RIPv2/ng, OSPFv3, RTMv4/v6, ARP/ND, NETIP(v4/v6) All the bit is set as 1… |
| 1.3.6.1.4.1.10876.101.1.81.18 | NodeissUDFilter | |||
| 1.3.6.1.4.1.10876.101.1.81.18.1 | TableissUDFilterTable | not-accessible | current | A table to configure User-Defined filter rules in the system. |
| 1.3.6.1.4.1.10876.101.1.81.18.1.1 | RowissUDFilterEntry | not-accessible | current | Each entry in this table is a User-Defined filter rule. Index to the table is User-Defined filter number. |
| 1.3.6.1.4.1.10876.101.1.81.18.1.1.1 | ColumnissUDFilterNo | not-accessible | current | User-Defined Filter rule number. This object is deprecated and the corresponding functionality is met with issUDFilter objects in fsissext.mib. |
| 1.3.6.1.4.1.10876.101.1.81.18.1.1.2 | ColumnissUDFilterPriority | read-write | current | The priority of the UDF filter can be used to decide which filter rule is applicable when the packet matches with more than one filter rules. Higher value of '… |
| 1.3.6.1.4.1.10876.101.1.81.18.1.1.3 | ColumnissUDFilterPktType | read-write | current | The packet header type to be filtered by User-Defined Filter. |
| 1.3.6.1.4.1.10876.101.1.81.18.1.1.4 | ColumnissUDFilterDstMacAddr | read-write | current | Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero which means dont care condition ie) any Dst Mac Add… |
| 1.3.6.1.4.1.10876.101.1.81.18.1.1.5 | ColumnissUDFilterSrcMacAddr | read-write | current | Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero which means dont care condition ie) any Src Mac address. This… |
| 1.3.6.1.4.1.10876.101.1.81.18.1.1.6 | ColumnissUDFilterProtocol | read-write | current | The type of protocol to be checked against the packet. The default value is 255. If the value is 255, it means that the protocol type can be anything and it wi… |
| 1.3.6.1.4.1.10876.101.1.81.18.1.1.7 | ColumnissUDFilterDstIpAddr | read-write | current | Destination IP address to be matched with the packet. This object is valid only if the 'issUDFilterPktType' is 'IP', 'UDP' or 'TCP'. |
| 1.3.6.1.4.1.10876.101.1.81.18.1.1.8 | ColumnissUDFilterSrcIpAddr | read-write | current | Source IP address to be matched with the packet. This object is valid only if the 'issUDFilterPktType' is 'IP', 'UDP' or 'TCP'. |
| 1.3.6.1.4.1.10876.101.1.81.18.1.1.9 | ColumnissUDFilterDstIpAddrMask | read-write | current | The IP subnet mask for Destination IP address. This object is valid only if the 'issUDFilterPktType' is 'IP', 'UDP' or 'TCP'. |
| 1.3.6.1.4.1.10876.101.1.81.18.1.1.10 | ColumnissUDFilterSrcIpAddrMask | read-write | current | The IP subnet mask for Source IP address. This object is valid only if the 'issUDFilterPktType' is 'IP', 'UDP' or 'TCP'. |
| 1.3.6.1.4.1.10876.101.1.81.18.1.1.11 | ColumnissUDFilterMinDstProtPort | read-write | current | The minimum port in the destination port range. Please note these ports are the TCP / UDP ports. This object is valid only if the 'issUDFilterPktType' is 'UDP'… |
| 1.3.6.1.4.1.10876.101.1.81.18.1.1.12 | ColumnissUDFilterMaxDstProtPort | read-write | current | The maximum port in the destination port range. Please note these ports are the TCP / UDP ports. This object is valid only if the 'issUDFilterPktType' is 'UDP'… |
| 1.3.6.1.4.1.10876.101.1.81.18.1.1.13 | ColumnissUDFilterMinSrcProtPort | read-write | current | The minimum port in the source port range. Please note these ports are the TCP / UDP ports. This object is valid only if the 'issUDFilterPktType' is 'UDP' or '… |
| 1.3.6.1.4.1.10876.101.1.81.18.1.1.14 | ColumnissUDFilterMaxSrcProtPort | read-write | current | The maximum port in the source port range. Please note these ports are the TCP / UDP ports. This object is valid only if the 'issUDFilterPktType' is 'UDP' or '… |
| 1.3.6.1.4.1.10876.101.1.81.18.1.1.15 | ColumnissUDFilterInPortList | read-write | current | Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable. If the incoming port list is '0', the filter rule is … |
| 1.3.6.1.4.1.10876.101.1.81.18.1.1.16 | ColumnissUDFilterOutPortList | read-write | current | Specifies the complete set of ports over which if the packet goes out, this filter rule will be applicable. If the outgoing port list is '0',the filter rule is… |
| 1.3.6.1.4.1.10876.101.1.81.18.1.1.17 | ColumnissUDFilterAction | read-write | current | Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be sent to the ports in 'out port list'. I… |
| 1.3.6.1.4.1.10876.101.1.81.18.1.1.18 | ColumnissUDFilterStatus | read-create | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.10876.101.1.81.19 | NodeecnProfile | |||
| 1.3.6.1.4.1.10876.101.1.81.19.1 | TableecnProfileTable | not-accessible | current | A profile table to configure Explicit Congestion Notification (ECN) in the system. |
| 1.3.6.1.4.1.10876.101.1.81.19.1.1 | RowecnProfileEntry | not-accessible | current | Each entry in this table is a Explicit Congestion Notification (ECN) profile . Index to the table is profile name. |
| 1.3.6.1.4.1.10876.101.1.81.19.1.1.1 | ColumnecnProfileName | not-accessible | current | ECN Profile Name |
| 1.3.6.1.4.1.10876.101.1.81.19.1.1.2 | ColumnecnProfileMinThreshold | read-write | current | Packets are treated normally when average queue size below minimum threshold (bytes). |
| 1.3.6.1.4.1.10876.101.1.81.19.1.1.3 | ColumnecnProfileMaxThreshold | read-write | current | Packets are marked congestion experienced when average queue size above maximum threshold (bytes). |
| 1.3.6.1.4.1.10876.101.1.81.19.1.1.4 | ColumnecnProfileProbability | read-write | current | The proportion of ECN marking varies linear with average queue size when average queue size between minimum and maximum thresholds. |
| 1.3.6.1.4.1.10876.101.1.81.19.1.1.5 | ColumnecnProfilePortList | read-write | current | Specifies the inteface lists to be applied ECN profile. e.g. 8040... : Port 1 and 6 ... |
| 1.3.6.1.4.1.10876.101.1.81.19.1.1.6 | ColumnecnProfileRowStatus | read-create | current | This object is used to create and delete rows in the ecnProfileTable. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| PortList | OCTET STRING | current | Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents… |