SUPERMICRO-MI-BGP-MIB
531 objects
The Proprietary BGP MIB Created for MI support
Imported Objects
| SNMPv2-SMI | Counter32 enterprises Gauge32 Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DateAndTime DisplayString RowStatus TruthValue |
| SUPERMICRO-BGP-MIB | BgpSafi InetAddress InetAddressType |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.10876.101.2.77 | IdentityfsMIBgp | The Proprietary BGP MIB Created for MI support | ||
| 1.3.6.1.4.1.10876.101.2.77.1 | ScalarfsMIBgp4GlobalTraceDebug | read-write | current | This object is used to enable global trace for the BGP module. A four byte integer value is specified for enabling the level of tracing. Each Bit in the four b… |
| 1.3.6.1.4.1.10876.101.2.77.2 | ScalarfsMIBgp4LocalAs | read-write | current | This is Global local autonomous system number. |
| 1.3.6.1.4.1.10876.101.2.77.3 | ScalarfsMIBgp4MaxPeerEntry | read-write | current | The Maximum number of peers supported by BGP |
| 1.3.6.1.4.1.10876.101.2.77.4 | ScalarfsMIBgp4MaxNoofRoutes | read-write | current | It represents the maximum number of routes in the routing table |
| 1.3.6.1.4.1.10876.101.2.77.5 | ScalarfsMIBgp4GRAdminStatus | read-write | current | This object is used to enable or disable GR capability in BGP speaker. |
| 1.3.6.1.4.1.10876.101.2.77.6 | ScalarfsMIBgp4GRRestartTimeInterval | read-write | current | This is the estimated time (in seconds) it will take for the BGP session to be re-established after a restart. Suggested default value should be less than or e… |
| 1.3.6.1.4.1.10876.101.2.77.7 | ScalarfsMIBgp4RestartExitReason | read-only | current | Describes the outcome of the last attempt at a graceful restart. If the value is 'none': no restart has yet been attempted. 'inProgress': a restart attempt is … |
| 1.3.6.1.4.1.10876.101.2.77.8 | ScalarfsMIBgp4GRSelectionDeferralTimeInterval | read-write | current | This interval is the upper bound on the amount of time a router defers its route selection. The value of this timer should be large enough, so as to provide al… |
| 1.3.6.1.4.1.10876.101.2.77.9 | ScalarfsMIBgp4GRStaleTimeInterval | read-write | current | This interval is the upper bound on the amount of time a router retains the stale routes. The GR stale time interval configured can be used only for the new pe… |
| 1.3.6.1.4.1.10876.101.2.77.10 | ScalarfsMIBgp4GRMode | read-only | current | This object indicates whether the BGP speaker is restarting speaker or receiving speaker. |
| 1.3.6.1.4.1.10876.101.2.77.11 | ScalarfsMIBgp4RestartSupport | read-write | current | The router's support for BGP graceful restart Options include: no restart support, only planned restarts, or both planned and unplanned restarts. This object i… |
| 1.3.6.1.4.1.10876.101.2.77.12 | ScalarfsMIBgp4RestartStatus | read-only | current | Current status of BGP graceful restart, it indicates whether the speaker restarted or not if it is restarted whether it is a planned restart or unplanned resta… |
| 1.3.6.1.4.1.10876.101.2.77.13 | ScalarfsMIBgp4ForwardingPreservation | read-only | current | This object indicates whether the forwarding plane is preserved during restart or not |
| 1.3.6.1.4.1.10876.101.2.77.14 | TablefsMIBgpContextTable | not-accessible | current | This context table contains the global parameters of BGP that is required to be configured for each context. |
| 1.3.6.1.4.1.10876.101.2.77.14.1 | RowfsMIBgpContextEntry | not-accessible | current | An Entry for the configuration in a particular VR. |
| 1.3.6.1.4.1.10876.101.2.77.14.1.1 | ColumnfsMIBgp4ContextId | not-accessible | current | The index value that uniquely identifies the virtual router in which the configuration is done. |
| 1.3.6.1.4.1.10876.101.2.77.14.1.2 | ColumnfsMIBgp4GlobalAdminStatus | read-write | current | The desired state of the BGP system. The BGP4 speaker is functionally active only when the global admin status is up. The global admin status can be made up on… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.3 | ColumnfsMIBgp4Identifier | read-write | current | This object configures the BGP Identifier in that VR. If admin status is made up, by default the BGP Identifier will take the value of highest interface addres… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.4 | ColumnfsMIBgp4Synchronization | read-write | current | Attribute to enable/disable synchronization within an AS. This object can be set only if fsMIBgp4LocalAs has been configured. |
| 1.3.6.1.4.1.10876.101.2.77.14.1.5 | ColumnfsMIBgp4DefaultLocalPref | read-write | current | The default value of local-pref that is to be sent in updates to internal peers.This object can be set only if fsMIBgp4LocalAs has been configured. |
| 1.3.6.1.4.1.10876.101.2.77.14.1.6 | ColumnfsMIBgp4AdvtNonBgpRt | read-write | current | This mib object can be used to configure the peer type to whom non-bgp routes can be propagated. external - indicates non-bgp routes can be exported to only ex… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.7 | ColumnfsMIBgp4TraceEnable | read-write | current | This object can be used to enable trace dynamically in BGP module. A four byte integer value is specified for enabling the level of tracing.Each Bit in the fou… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.8 | ColumnfsMIBgp4DebugEnable | read-write | current | This object can be used to enable debug dynamically in BGP module. Its a four byte integer value specified for enabling the level of debugging. Each Bit in the… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.9 | ColumnfsMIBgp4OverlappingRoute | read-write | current | This object is used to configure the BGP speaker's policy for handling the overlapping routes. When an overlapping route is received, depending upon the config… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.10 | ColumnfsMIBgp4AlwaysCompareMED | read-write | current | If this object is set to disable, then in best route decision process, MED will be compared only between routes received from the same autonomous system. If se… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.11 | ColumnfsMIBgp4DefaultOriginate | read-write | current | If this object is set to enable/disable the redistribution and advertisement of the default route (0.0.0.0/0). By default, the default routes are not redistrib… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.12 | ColumnfsMIBgp4DefaultIpv4UniCast | read-write | current | If this object is set to enable, and if a neighbor is created, then the MP IPv4 Unicast Address Family Capability will be negotiate for that peer. If this obje… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.13 | ColumnfsMIBgp4IsTrapEnabled | read-write | current | If this object is set to disable, then the NOTIFICATION messages wont be sent to the SNMP Manager. If enabled, NOTIFICATION messages are sent. |
| 1.3.6.1.4.1.10876.101.2.77.14.1.14 | ColumnfsMIBgp4NextHopProcessingInterval | read-write | current | This object is used to configure the interval at which next hops will be mointored for reachablity |
| 1.3.6.1.4.1.10876.101.2.77.14.1.15 | ColumnfsMIBgp4IBGPRedistributionStatus | read-write | current | If this object is set to enable, IBGP routes will also be redistributed to other IGP protocols when redistribution is enabled for that protocol |
| 1.3.6.1.4.1.10876.101.2.77.14.1.16 | ColumnfsMIBgp4RRDAdminStatus | read-write | current | Controls redistribution of Direct, Static, IGP(OSPF,RIP) routes into BGP. If this object is set to enable, then routes from protocols as specified by fsMIBgp4R… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.17 | ColumnfsMIBgp4RRDProtoMaskForEnable | read-write | current | The bit mask of source protocols from which routes are imported to BGP.(LSB corresponds to Bit 0) Bit 1, if set, indicates that direct routes can be redistribu… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.18 | ColumnfsMIBgp4RRDSrcProtoMaskForDisable | read-write | current | The bit mask of source protocols from which redistribution to BGP is disabled.(LSB corresponds to Bit 0) Bit 1, if set, indicates that direct routes cannot be … |
| 1.3.6.1.4.1.10876.101.2.77.14.1.19 | ColumnfsMIBgp4RRDDefaultMetric | read-write | current | The default metric value for the IGP routes and static route. If configured to 0, the metric received from the IGP route will be used. If configured to other v… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.20 | ColumnfsMIBgp4RRDRouteMapName | read-write | current | Name Identifies the specified route-map in the list of route-maps. If this Object needs to be changed, first reset this object and then configure the new value. |
| 1.3.6.1.4.1.10876.101.2.77.14.1.21 | ColumnfsMIBgp4RRDMatchTypeEnable | read-write | current | Match type Enable specifies the OSPF route type that needs to be redistributed into BGP, This object is used only ospf redistribution. |
| 1.3.6.1.4.1.10876.101.2.77.14.1.22 | ColumnfsMIBgp4RRDMatchTypeDisable | read-write | current | Match type Disable specifies the OSPF route type that should be disbled from redistribution into BGP. This object is used only for OSPF protocol. |
| 1.3.6.1.4.1.10876.101.2.77.14.1.23 | ColumnfsMIBgp4AscConfedId | read-write | current | The Local Confederation Identification number of the AS confederation, a value of zero indicates the absence of this value. The object fsbgp4LocalAs must be co… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.24 | ColumnfsMIBgp4AscConfedBestPathCompareMED | read-write | current | This object is used to compare MED among paths learned from confed peers. if this object value is set and AS path contains only AS_CONFED segments then then ME… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.25 | ColumnfsMIBgp4RflbgpClusterId | read-write | current | The configured Cluster-ID of the local router. By default, when the BGP speaker acts as Route Reflector, the BGP Identifier is used as the cluster id. Administ… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.26 | ColumnfsMIBgp4RflRflSupport | read-write | current | The desired support of the Route Reflector in the cluster. Note that none(1) value is for read-only. This object can be set only if fsMIBgp4LocalAS is configur… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.27 | ColumnfsMIBgp4RfdCutOff | read-write | current | The figure-of-merit value above which the route will be suppressed. This object can be set only if fsMIBgp4RfdAdminStatus is disabled is set to down and fsMIBg… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.28 | ColumnfsMIBgp4RfdReuse | read-write | current | The figure-of-merit value below which the suppressed route will be reused. This object can be set only if fsMIBgp4RfdAdminStatus is disabled and fsMIBgp4LocalA… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.29 | ColumnfsMIBgp4RfdCeiling | read-only | current | The highest value the figure-of-merit can attain. |
| 1.3.6.1.4.1.10876.101.2.77.14.1.30 | ColumnfsMIBgp4RfdMaxHoldDownTime | read-write | current | Maximum time (in seconds) a route can be suppressed. This object can be set only if fsMIBgp4RfdAdminStatus is disabled and fsMIBgp4LocalAS is configured. |
| 1.3.6.1.4.1.10876.101.2.77.14.1.31 | ColumnfsMIBgp4RfdDecayHalfLifeTime | read-write | current | The time duration in seconds during which the figure-of-merit will be reduced by half. This object can be set only if fsMIBgp4RfdAdminStatus is disabled and fs… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.32 | ColumnfsMIBgp4RfdDecayTimerGranularity | read-write | current | Time granularity in seconds used to perform all decay calculations. This object can be set only if fsMIBgp4RfdAdminStatus is disabled and fsMIBgp4LocalAS is co… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.33 | ColumnfsMIBgp4RfdReuseTimerGranularity | read-write | current | Time interval between evaluations of the reuse lists. This object can be set only if fsMIBgp4RfdAdminStatus is disabled and fsMIBgp4LocalAS is configured. |
| 1.3.6.1.4.1.10876.101.2.77.14.1.34 | ColumnfsMIBgp4RfdReuseIndxArraySize | read-write | current | Size of reuse index arrays.This object can be set only if fsMIBgp4GlobalAdminStatus is set to down and fsMIBgp4LocalAS is configured. |
| 1.3.6.1.4.1.10876.101.2.77.14.1.35 | ColumnfsMIBgp4RfdAdminStatus | read-write | current | The desired state of the RouteFlap Dampening feature of the BGP system. The SupermicroBGP4 speaker's route flap dampending is functionally active only when the… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.36 | ColumnfsMIBgp4CommMaxInFTblEntries | read-write | current | Maximum Number of Entries in the Input Community Filter Table. This object can not be set to a higher value than the initial value of the object.However initia… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.37 | ColumnfsMIBgp4CommMaxOutFTblEntries | read-write | current | Maximum number of entries in the outgoing community filter table. This object can not be set to a higher value than the initial value of the object.However ini… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.38 | ColumnfsMIBgp4ExtCommMaxInFTblEntries | read-write | current | Maximum Number of Entries in the Input Extended Community Filter Table. This object can not be set to a higher value than the initial value of the object.Howev… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.39 | ColumnfsMIBgp4ExtCommMaxOutFTblEntries | read-write | current | Maximum number of entries in the outgoing extended community filter table. This object can not be set to a higher value than the initial value of the object.Ho… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.40 | ColumnfsMIBgp4CapabilitySupportAvailable | read-write | current | This variable determines whether the Capability Advertisement Support is enabled or not.This object can be set only if fsMIBgp4GlobalAdminStatus is set to down… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.41 | ColumnfsMIBgp4MaxCapsPerPeer | read-write | current | The maximum number of Capabilities that can be supported per peer or received from peer. This object can not be set to a higher value than the initial value of… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.42 | ColumnfsMIBgp4MaxInstancesPerCap | read-write | current | The maximum number of Instances of same Capability code can be advertised to peer or received from peer. This object can not be set to a higher value than the … |
| 1.3.6.1.4.1.10876.101.2.77.14.1.43 | ColumnfsMIBgp4MaxCapDataSize | read-write | current | The maximum size of the Capability Data size of each Capability. To enable packing, the size should be multiples of 4. This object can not be set to a higher v… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.44 | ColumnfsMIBgp4PreferenceValue | read-write | current | Preference value for RIP routes. Use '0' to set default value |
| 1.3.6.1.4.1.10876.101.2.77.14.1.45 | ColumnfsMIBgp4ContextStatus | read-write | current | this is used to enable or disable status of context |
| 1.3.6.1.4.1.10876.101.2.77.14.1.46 | ColumnfsMIBgp4IBGPMaxPaths | read-write | current | Maximum number of internal BGP multipath routes to be added per destination network in Routing table. When this object takes the value 1, then only best route … |
| 1.3.6.1.4.1.10876.101.2.77.14.1.47 | ColumnfsMIBgp4EBGPMaxPaths | read-write | current | Maximum number of external BGP multipath routes to be added per destination network in Routing table. When this object takes the value 1, then only best route … |
| 1.3.6.1.4.1.10876.101.2.77.14.1.48 | ColumnfsMIBgp4EIBGPMaxPaths | read-write | current | Maximum number of external plus internal BGP multipath routes (with same AS PATH) to be added per destination network in Routing table. When this object takes … |
| 1.3.6.1.4.1.10876.101.2.77.14.1.49 | ColumnfsMIBgp4OperIBGPMaxPaths | read-only | current | Operational value for Maximum number of internal BGP multipath routes to be added per destination network in Routing table. When this object takes the value 1,… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.50 | ColumnfsMIBgp4OperEBGPMaxPaths | read-only | current | Operational value for Maximum number of external BGP multipath routes that to be added per destination network in Routing table. When this object takes the val… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.51 | ColumnfsMIBgp4OperEIBGPMaxPaths | read-only | current | Operational value for Maximum number of external plus internal BGP multipath routes (with same AS PATH) to be added in Routing table. When this object takes th… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.52 | ColumnfsMIBgp4FourByteASNSupportStatus | read-write | current | This object is used to enable or disable 4 byte ASN support in BGP Speaker. This can be configured only if fsMIBgp4GlobalAdminStatus is down. |
| 1.3.6.1.4.1.10876.101.2.77.14.1.53 | ColumnfsMIBgp4FourByteASNotationType | read-write | current | This object denotes the notation to be used to display the 4 byte ASN. This will change only the way the AS number is represented within router show commands i… |
| 1.3.6.1.4.1.10876.101.2.77.14.1.54 | ColumnfsMIBgp4LocalAsNo | read-write | current | This is local autonomous system number specific to a Context. |
| 1.3.6.1.4.1.10876.101.2.77.14.1.55 | ColumnfsMIBgp4RIBRoutes | read-only | current | This is the total number of the routes present in the RIB of a context at the given instance. |
| 1.3.6.1.4.1.10876.101.2.77.15 | TablefsMIBgp4RRDMetricTable | not-accessible | current | A table describing the configuration of metric values to the redistributed routes. |
| 1.3.6.1.4.1.10876.101.2.77.15.1 | RowfsMIBgp4RRDMetricEntry | not-accessible | current | Information describing the configuration of single entry. |
| 1.3.6.1.4.1.10876.101.2.77.15.1.1 | ColumnfsMIBgp4RRDMetricProtocolId | not-accessible | current | Protocol Id for which the Metric value needs to be changed by the User. |
| 1.3.6.1.4.1.10876.101.2.77.15.1.2 | ColumnfsMIBgp4RRDMetricValue | read-write | current | The Metric value to be considered instead of the default value from RTM for the protocol specified. If the value not secified by the user, default metric value… |
| 1.3.6.1.4.1.10876.101.2.77.16 | NodefsMIBgpComm | |||
| 1.3.6.1.4.1.10876.101.2.77.16.1 | TablefsMIBgp4CommInFilterTable | not-accessible | current | This table is used to configure the incoming filter status for a given community value |
| 1.3.6.1.4.1.10876.101.2.77.16.1.1 | RowfsMIBgp4CommInFilterEntry | not-accessible | current | Incoming Communities Filter Table Entry |
| 1.3.6.1.4.1.10876.101.2.77.16.1.1.1 | ColumnfsMIBgp4InFilterCommVal | not-accessible | current | The community value for which the input filtering policy is to be updated |
| 1.3.6.1.4.1.10876.101.2.77.16.1.1.2 | ColumnfsMIBgp4CommIncomingFilterStatus | read-create | current | Incoming filtering policy for the community. o none - is for read-only o accept - Accept the community value. o deny - Deny the community value. |
| 1.3.6.1.4.1.10876.101.2.77.16.1.1.3 | ColumnfsMIBgp4InFilterRowStatus | read-create | current | Row status for creating entries into this table.This object can be set only if fsMIBgp4LocalAs is configured. |
| 1.3.6.1.4.1.10876.101.2.77.16.2 | TablefsMIBgp4CommOutFilterTable | not-accessible | current | This table is used to configure the outgoing filter status for a given community value |
| 1.3.6.1.4.1.10876.101.2.77.16.2.1 | RowfsMIBgp4CommOutFilterEntry | not-accessible | current | Outgoing Communities Filter Table Entry |
| 1.3.6.1.4.1.10876.101.2.77.16.2.1.1 | ColumnfsMIBgp4OutFilterCommVal | not-accessible | current | The community value for which the outgoing filtering policy is to be updated |
| 1.3.6.1.4.1.10876.101.2.77.16.2.1.2 | ColumnfsMIBgp4CommOutgoingFilterStatus | read-create | current | Outgoing filtering policy for the community. o none - is for read-only o advertise - Advertise the community value. o filter - Filter the community value. |
| 1.3.6.1.4.1.10876.101.2.77.16.2.1.3 | ColumnfsMIBgp4OutFilterRowStatus | read-create | current | Row status for creating entries into this table.This object can be set only if fsMIBgp4LocalAs is configured. |
| 1.3.6.1.4.1.10876.101.2.77.17 | NodefsMIBgpExtComm | |||
| 1.3.6.1.4.1.10876.101.2.77.17.1 | TablefsMIBgp4ExtCommInFilterTable | not-accessible | current | This table is used to configure the incoming filter status for a given extended community value |
| 1.3.6.1.4.1.10876.101.2.77.17.1.1 | RowfsMIBgp4ExtCommInFilterEntry | not-accessible | current | Incoming Extended Communities Filter Table Entry |
| 1.3.6.1.4.1.10876.101.2.77.17.1.1.1 | ColumnfsMIBgp4ExtCommInFilterCommVal | not-accessible | current | The extended community value for which the input filtering policy is to be updated |
| 1.3.6.1.4.1.10876.101.2.77.17.1.1.2 | ColumnfsMIBgp4ExtCommIncomingFilterStatus | read-create | current | Incoming filtering policy for the extended community. o none - is for read-only o accept - Accept the extended community value. o deny - Deny the extended comm… |
| 1.3.6.1.4.1.10876.101.2.77.17.1.1.3 | ColumnfsMIBgp4ExtCommInFilterRowStatus | read-create | current | Row Status for creating the entries into this table.This object can be set only if fsMIBgp4LocalAs is configured. |
| 1.3.6.1.4.1.10876.101.2.77.17.2 | TablefsMIBgp4ExtCommOutFilterTable | not-accessible | current | This table is used to configure the outgoing filter status for a given extended community value |
| 1.3.6.1.4.1.10876.101.2.77.17.2.1 | RowfsMIBgp4ExtCommOutFilterEntry | not-accessible | current | Outgoing Extended Communities Filter Table Entry |
| 1.3.6.1.4.1.10876.101.2.77.17.2.1.1 | ColumnfsMIBgp4ExtCommOutFilterCommVal | not-accessible | current | The extended community value for which the outgoing filtering policy is to be updated |
| 1.3.6.1.4.1.10876.101.2.77.17.2.1.2 | ColumnfsMIBgp4ExtCommOutgoingFilterStatus | read-create | current | Outgoing filtering policy for the extended community. o none - is for read-only o advertise - Advertise the extended community value. o filter - Filter the ext… |
| 1.3.6.1.4.1.10876.101.2.77.17.2.1.3 | ColumnfsMIBgp4ExtCommOutFilterRowStatus | read-create | current | Row Status to create entries into this table.This object can be set only if fsMIBgp4LocalAs is configured. |
| 1.3.6.1.4.1.10876.101.2.77.18 | NodefsMIBgp4TCPMD5Auth | |||
| 1.3.6.1.4.1.10876.101.2.77.18.1 | TablefsMIBgp4TCPMD5AuthTable | not-accessible | current | TCP MD5 Authientication Table |
| 1.3.6.1.4.1.10876.101.2.77.18.1.1 | RowfsMIBgp4TCPMD5AuthEntry | not-accessible | current | Entry corresponds to the TCP MD5 authentication password. |
| 1.3.6.1.4.1.10876.101.2.77.18.1.1.1 | ColumnfsMIBgp4TCPMD5AuthPeerType | not-accessible | current | Address Family Identifier of the peer remote address. |
| 1.3.6.1.4.1.10876.101.2.77.18.1.1.2 | ColumnfsMIBgp4TCPMD5AuthPeerAddr | not-accessible | current | The IP address of the peer for which the TCP MD5 Authentication Password has to be set. to be read. |
| 1.3.6.1.4.1.10876.101.2.77.18.1.1.3 | ColumnfsMIBgp4TCPMD5AuthPassword | read-write | current | The TCP MD5 Authentication Password that has to be sent with all TCP packets originated from the peer. |
| 1.3.6.1.4.1.10876.101.2.77.18.1.1.4 | ColumnfsMIBgp4TCPMD5AuthPwdSet | read-write | current | This object indicates whether TCP MD5 password needs to be set/reset for the peer. This object needs to be set before the object fsMIBgp4TCPMD5AuthPassword can… |
| 1.3.6.1.4.1.10876.101.2.77.19 | NodefsMIBgpAsc | |||
| 1.3.6.1.4.1.10876.101.2.77.19.1 | TablefsMIBgpAscConfedPeerTable | not-accessible | current | BGP peer confederation table, this table contains information about the Member-ASs of the confederation |
| 1.3.6.1.4.1.10876.101.2.77.19.1.1 | RowfsMIBgpAscConfedPeerEntry | not-accessible | current | Entry containing information about a member-AS of the confederation. |
| 1.3.6.1.4.1.10876.101.2.77.19.1.1.1 | ColumnfsMIBgpAscConfedPeerASNo | not-accessible | current | The local AS number of member-AS, a value of zero indicates the absence of this value |
| 1.3.6.1.4.1.10876.101.2.77.19.1.1.2 | ColumnfsMIBgpAscConfedPeerStatus | read-write | current | This object is used to enable or disable the member-AS. Use disable, if member-AS entry needs to disabled, Use enable, if member-AS entry needs to be enabled. |
| 1.3.6.1.4.1.10876.101.2.77.20 | TablefsMIBgp4MpeBgpPeerTable | not-accessible | current | BGP peer table. This table contains, one entry per BGP peer, information about the connections with BGP peers. |
| 1.3.6.1.4.1.10876.101.2.77.20.1 | RowfsMIBgp4MpeBgpPeerEntry | not-accessible | current | Entry containing information about the connection with a BGP peer. |
| 1.3.6.1.4.1.10876.101.2.77.20.1.1 | ColumnfsMIBgp4mpebgpPeerIdentifier | read-only | current | The BGP Identifier of this entry's BGP peer. |
| 1.3.6.1.4.1.10876.101.2.77.20.1.2 | ColumnfsMIBgp4mpebgpPeerRemoteAddrType | not-accessible | current | Type of the remote peer |
| 1.3.6.1.4.1.10876.101.2.77.20.1.3 | ColumnfsMIBgp4mpebgpPeerLocalAs | read-write | current | It is used to configure as Local As per peer |
| 1.3.6.1.4.1.10876.101.2.77.20.1.4 | ColumnfsMIBgp4mpebgpPeerState | read-only | current | The BGP peer connection state. |
| 1.3.6.1.4.1.10876.101.2.77.20.1.5 | ColumnfsMIBgp4mpebgpPeerAdminStatus | read-write | current | The desired state of the BGP connection. A transition from 'stop' to 'start' will cause the BGP Start Event to be generated. A transition from 'start' to 'stop… |
| 1.3.6.1.4.1.10876.101.2.77.20.1.6 | ColumnfsMIBgp4mpebgpPeerNegotiatedVersion | read-only | current | The negotiated version of BGP running between the two peers. |
| 1.3.6.1.4.1.10876.101.2.77.20.1.7 | ColumnfsMIBgp4mpebgpPeerLocalAddr | read-only | current | The local IP address of this entry's BGP connection. |
| 1.3.6.1.4.1.10876.101.2.77.20.1.8 | ColumnfsMIBgp4mpebgpPeerLocalPort | read-only | current | The local port for the TCP connection between the BGP peers. |
| 1.3.6.1.4.1.10876.101.2.77.20.1.9 | ColumnfsMIBgp4mpebgpPeerRemoteAddr | not-accessible | current | The remote IP address of this entry's BGP peer. |
| 1.3.6.1.4.1.10876.101.2.77.20.1.10 | ColumnfsMIBgp4mpebgpPeerRemotePort | read-only | current | The remote port for the TCP connection between the BGP peers. Note that the objects bgpPeerLocalAddr, bgpPeerLocalPort, bgpPeerRemoteAddr and bgpPeerRemotePort… |
| 1.3.6.1.4.1.10876.101.2.77.20.1.11 | ColumnfsMIBgp4mpebgpPeerRemoteAs | read-only | current | The remote autonomous system number. |
| 1.3.6.1.4.1.10876.101.2.77.20.1.12 | ColumnfsMIBgp4mpebgpPeerInUpdates | read-only | current | The number of BGP UPDATE messages received on this connection. This object should be initialized to zero (0) when the connection is established. |
| 1.3.6.1.4.1.10876.101.2.77.20.1.13 | ColumnfsMIBgp4mpebgpPeerOutUpdates | read-only | current | The number of BGP UPDATE messages transmitted on this connection. This object should be initialized to zero (0) when the connection is established. |
| 1.3.6.1.4.1.10876.101.2.77.20.1.14 | ColumnfsMIBgp4mpebgpPeerInTotalMessages | read-only | current | The total number of messages received from the remote peer on this connection. This object should be initialized to zero when the connection is established. |
| 1.3.6.1.4.1.10876.101.2.77.20.1.15 | ColumnfsMIBgp4mpebgpPeerOutTotalMessages | read-only | current | The total number of messages transmitted to the remote peer on this connection. This object should be initialized to zero when the connection is established. |
| 1.3.6.1.4.1.10876.101.2.77.20.1.16 | ColumnfsMIBgp4mpebgpPeerLastError | read-only | current | The last error code and subcode seen by this peer on this connection. If no error has occurred, this field is zero. Otherwise, the first byte of this two byte … |
| 1.3.6.1.4.1.10876.101.2.77.20.1.17 | ColumnfsMIBgp4mpebgpPeerFsmEstablishedTransitions | read-only | current | The total number of times the BGP FSM transitioned into the established state. |
| 1.3.6.1.4.1.10876.101.2.77.20.1.18 | ColumnfsMIBgp4mpebgpPeerFsmEstablishedTime | read-only | current | This timer indicates how long (in seconds) this peer has been in the Established state or how long since this peer was last in the Established state. It is set… |
| 1.3.6.1.4.1.10876.101.2.77.20.1.19 | ColumnfsMIBgp4mpebgpPeerConnectRetryInterval | read-write | current | Time interval in seconds for the ConnectRetry timer. The suggested value for this timer is 120 seconds. |
| 1.3.6.1.4.1.10876.101.2.77.20.1.20 | ColumnfsMIBgp4mpebgpPeerHoldTime | read-only | current | Time interval in seconds for the Hold Timer established with the peer. The value of this object is calculated by this BGP speaker by using the smaller of the v… |
| 1.3.6.1.4.1.10876.101.2.77.20.1.21 | ColumnfsMIBgp4mpebgpPeerKeepAlive | read-only | current | Time interval in seconds for the KeepAlive timer established with the peer. The value of this object is calculated by this BGP speaker such that, when compared… |
| 1.3.6.1.4.1.10876.101.2.77.20.1.22 | ColumnfsMIBgp4mpebgpPeerHoldTimeConfigured | read-write | current | Time interval in seconds for the Hold Time configured for this BGP speaker with this peer. This value is placed in an OPEN message sent to this peer by this BG… |
| 1.3.6.1.4.1.10876.101.2.77.20.1.23 | ColumnfsMIBgp4mpebgpPeerKeepAliveConfigured | read-write | current | Time interval in seconds for the KeepAlive timer configured for this BGP speaker with this peer. The value of this object will only determine the KEEPALIVE mes… |
| 1.3.6.1.4.1.10876.101.2.77.20.1.24 | ColumnfsMIBgp4mpebgpPeerMinASOriginationInterval | read-write | current | Time interval in seconds for the MinASOriginationInterval timer. The suggested value for this timer is 15 seconds. |
| 1.3.6.1.4.1.10876.101.2.77.20.1.25 | ColumnfsMIBgp4mpebgpPeerMinRouteAdvertisementInterval | read-write | current | Time interval in seconds for the MinRouteAdvertisementInterval timer. The suggested value for this timer is 30 seconds. |
| 1.3.6.1.4.1.10876.101.2.77.20.1.26 | ColumnfsMIBgp4mpebgpPeerInUpdateElapsedTime | read-only | current | Elapsed time in seconds since the last BGP UPDATE message was received from the peer. Each time bgpPeerInUpdates is incremented, the value of this object is se… |
| 1.3.6.1.4.1.10876.101.2.77.20.1.27 | ColumnfsMIBgp4mpebgpPeerEndOfRIBMarkerSentStatus | read-only | current | This object indicates that whether the End-Of-RIB marker sent to peer or not |
| 1.3.6.1.4.1.10876.101.2.77.20.1.28 | ColumnfsMIBgp4mpebgpPeerEndOfRIBMarkerReceivedStatus | read-only | current | This object indicates that whether the End-Of-RIB marker received from peer or not |
| 1.3.6.1.4.1.10876.101.2.77.20.1.29 | ColumnfsMIBgp4mpebgpPeerRestartMode | read-only | current | This object indicates whether the peer BGP speaker is restarting speaker or receiving speaker or not having GR capability |
| 1.3.6.1.4.1.10876.101.2.77.20.1.30 | ColumnfsMIBgp4mpePeerRestartTimeInterval | read-only | current | This is the time (in seconds) received from peer through GR capability of open message. This is used in receiving speaker to make sure that the restarting spea… |
| 1.3.6.1.4.1.10876.101.2.77.20.1.31 | ColumnfsMIBgp4mpePeerAllowAutomaticStart | read-write | current | This MIB object specifies whether BGP session with the associated peer can be started automatically. This object when set to 'disabled', requires manual start … |
| 1.3.6.1.4.1.10876.101.2.77.20.1.32 | ColumnfsMIBgp4mpePeerAllowAutomaticStop | read-write | current | This MIB object specifies whether a BGP connection needs to be automatically stopped after a TCP connect-retry count value specified by MIB object 'fsMIBgp4mpe… |
| 1.3.6.1.4.1.10876.101.2.77.20.1.33 | ColumnfsMIBgp4mpebgpPeerIdleHoldTimeConfigured | read-write | current | IdleHoldTime specifies the length of time the BGP peer is held in the Idle state prior to allowing the next automatic restart. The IdleHoldTime is configured o… |
| 1.3.6.1.4.1.10876.101.2.77.20.1.34 | ColumnfsMIBgp4mpeDampPeerOscillations | read-write | current | The DampPeerOscillations option specifies that the implementation engages additional logic to damp the oscillations of BGP peers in the face of series of autom… |
| 1.3.6.1.4.1.10876.101.2.77.20.1.35 | ColumnfsMIBgp4mpePeerDelayOpen | read-write | current | This MIB object allows configuration option to enable/disable delay in sending of OPEN messages to the BGP peer for a specific time period (DelayOpenTime). The… |
| 1.3.6.1.4.1.10876.101.2.77.20.1.36 | ColumnfsMIBgp4mpebgpPeerDelayOpenTimeConfigured | read-write | current | The DelayOpen time specifies the amount of time the BGP Peer should delay in sending the OPEN message to the remote peer. If the fsMIBgp4mpePeerDelayOpen optio… |
| 1.3.6.1.4.1.10876.101.2.77.20.1.37 | ColumnfsMIBgp4mpePeerPrefixUpperLimit | read-write | current | BGP speaker imposes a locally-configured, upper bound on the number of address prefixes the speaker is willing to accept from a neighbor. The default value is … |
| 1.3.6.1.4.1.10876.101.2.77.20.1.38 | ColumnfsMIBgp4mpePeerTcpConnectRetryCnt | read-write | current | This counter denotes the Maximum number of times the BGP Peer has tried to issue a TCP-Connect with its neighboring peers. The default value for the counter is… |
| 1.3.6.1.4.1.10876.101.2.77.20.1.39 | ColumnfsMIBgp4mpePeerTcpCurrentConnectRetryCnt | read-only | current | This counter denotes the number of times the BGP Peer has tried to issue a TCP-Connect with its neighboring peers. It is an internal value. It increments for e… |
| 1.3.6.1.4.1.10876.101.2.77.20.1.40 | ColumnfsMIBgp4mpeIsPeerDamped | read-only | current | This MIB object specifies the PeerDamped Status. If it is enabled, it denotes that the peer is in damped state. If it is disabled, it denotes that either the p… |
| 1.3.6.1.4.1.10876.101.2.77.20.1.41 | ColumnfsMIBgp4mpePeerSessionAuthStatus | read-only | current | This object indicates whether peer-session is TCP MD5/TCP-AO authenticated or not. If no session is established yet, its value is no-session |
| 1.3.6.1.4.1.10876.101.2.77.20.1.42 | ColumnfsMIBgp4mpePeerTCPAOKeyIdInUse | read-only | current | Key id of the MKT which is used by the TCP session of the peer, this field will be valid only when fsMIBgp4mpePeerSessionAuthStatus has value authenticatedTcpAo |
| 1.3.6.1.4.1.10876.101.2.77.20.1.43 | ColumnfsMIBgp4mpePeerTCPAOAuthNoMKTDiscard | read-write | current | Discard packet for the peer, if packets are received with TCP-AO and no matching MKT is found, default value is accept |
| 1.3.6.1.4.1.10876.101.2.77.20.1.44 | ColumnfsMIBgp4mpePeerTCPAOAuthICMPAccept | read-write | current | Accept ICMPv4 type 3 & ICMPv6 type 1 messages for the TCP-AO authenticated peer, default value is ignore |
| 1.3.6.1.4.1.10876.101.2.77.20.1.45 | ColumnfsMIBgp4mpePeerIpPrefixNameIn | read-write | current | This object is used to configure the IP Prefix list name in IN direction for this peer entry. |
| 1.3.6.1.4.1.10876.101.2.77.20.1.46 | ColumnfsMIBgp4mpePeerIpPrefixNameOut | read-write | current | This object is used to configure the IP Prefix list name in OUT direction for this peer entry. |
| 1.3.6.1.4.1.10876.101.2.77.21 | TablefsMIBgp4MpeBgp4PathAttrTable | not-accessible | current | The BGP-4 Received Path Attribute Table contains information about paths to destination networks received from all BGP4 peers. |
| 1.3.6.1.4.1.10876.101.2.77.21.1 | RowfsMIBgp4MpeBgp4PathAttrEntry | not-accessible | current | Information about a path to a network. |
| 1.3.6.1.4.1.10876.101.2.77.21.1.1 | ColumnfsMIBgp4mpebgp4PathAttrRouteAfi | not-accessible | current | The AFI of the prefix |
| 1.3.6.1.4.1.10876.101.2.77.21.1.2 | ColumnfsMIBgp4mpebgp4PathAttrRouteSafi | not-accessible | current | The SAFI of the prefix |
| 1.3.6.1.4.1.10876.101.2.77.21.1.3 | ColumnfsMIBgp4mpebgp4PathAttrPeerType | not-accessible | current | The AFI of the peer |
| 1.3.6.1.4.1.10876.101.2.77.21.1.4 | ColumnfsMIBgp4mpebgp4PathAttrPeer | not-accessible | current | The IP address of the peer where the path information was learned. |
| 1.3.6.1.4.1.10876.101.2.77.21.1.5 | ColumnfsMIBgp4mpebgp4PathAttrIpAddrPrefixLen | not-accessible | current | Length in bits of the IP address prefix in the Network Layer Reachability Information field. |
| 1.3.6.1.4.1.10876.101.2.77.21.1.6 | ColumnfsMIBgp4mpebgp4PathAttrIpAddrPrefix | not-accessible | current | An IP address prefix in the Network Layer Reachability Information field. This object is an IP address containing the prefix with length specified by bgp4PathA… |
| 1.3.6.1.4.1.10876.101.2.77.21.1.7 | ColumnfsMIBgp4mpebgp4PathAttrOrigin | read-only | current | The ultimate origin of the path information. |
| 1.3.6.1.4.1.10876.101.2.77.21.1.8 | ColumnfsMIBgp4mpebgp4PathAttrASPathSegment | read-only | current | The sequence of AS path segments. Each AS path segment is represented by a triple <type, length, value>. The type is a 1-octet field which has two possible val… |
| 1.3.6.1.4.1.10876.101.2.77.21.1.9 | ColumnfsMIBgp4mpebgp4PathAttrNextHop | read-only | current | The address of the border router that should be used for the destination network. |
| 1.3.6.1.4.1.10876.101.2.77.21.1.10 | ColumnfsMIBgp4mpebgp4PathAttrMultiExitDisc | read-only | current | This metric is used to discriminate between multiple exit points to an adjacent autonomous system. A value of -1 indicates the absence of this attribute. |
| 1.3.6.1.4.1.10876.101.2.77.21.1.11 | ColumnfsMIBgp4mpebgp4PathAttrLocalPref | read-only | current | The originating BGP4 speaker's degree of preference for an advertised route. A value of -1 indicates the absence of this attribute. |
| 1.3.6.1.4.1.10876.101.2.77.21.1.12 | ColumnfsMIBgp4mpebgp4PathAttrAtomicAggregate | read-only | current | Whether or not the local system has selected a less specific route without selecting a more specific route. |
| 1.3.6.1.4.1.10876.101.2.77.21.1.13 | ColumnfsMIBgp4mpebgp4PathAttrAggregatorAS | read-only | current | The AS number of the last BGP4 speaker that performed route aggregation. A value of zero (0) indicates the absence of this attribute. |
| 1.3.6.1.4.1.10876.101.2.77.21.1.14 | ColumnfsMIBgp4mpebgp4PathAttrAggregatorAddr | read-only | current | The IP address of the last BGP4 speaker that performed route aggregation. A value of 0.0.0.0 indicates the absence of this attribute. |
| 1.3.6.1.4.1.10876.101.2.77.21.1.15 | ColumnfsMIBgp4mpebgp4PathAttrCalcLocalPref | read-only | current | The degree of preference calculated by the receiving BGP4 speaker for an advertised route. A value of -1 indicates the absence of this attribute. |
| 1.3.6.1.4.1.10876.101.2.77.21.1.16 | ColumnfsMIBgp4mpebgp4PathAttrBest | read-only | current | An indication of whether or not this route was chosen as the best BGP4 route. |
| 1.3.6.1.4.1.10876.101.2.77.21.1.17 | ColumnfsMIBgp4mpebgp4PathAttrCommunity | read-only | current | The community values received for this destinatin from the peer |
| 1.3.6.1.4.1.10876.101.2.77.21.1.18 | ColumnfsMIBgp4mpebgp4PathAttrOriginatorId | read-only | current | The Originator-ID identifying the router that initially advertised this destination to a Route Reflector. A value of 0.0.0.0 indicates the absence of this attr… |
| 1.3.6.1.4.1.10876.101.2.77.21.1.19 | ColumnfsMIBgp4mpebgp4PathAttrClusterList | read-only | current | A sequence of four octet long values Cluster-IDs representing the reflection path that the route has passed. Each four octet long value represents the ID of a … |
| 1.3.6.1.4.1.10876.101.2.77.21.1.20 | ColumnfsMIBgp4mpebgp4PathAttrExtCommunity | read-only | current | The extended community values received for this destinatin from the peer |
| 1.3.6.1.4.1.10876.101.2.77.21.1.21 | ColumnfsMIBgp4mpebgp4PathAttrUnknown | read-only | current | One or more path attributes not understood by this BGP4 speaker. Size zero (0) indicates the absence of such attribute(s). Octets beyond the maximum size, if a… |
| 1.3.6.1.4.1.10876.101.2.77.21.1.22 | ColumnfsMIBgp4mpebgp4PathAttrLabel | read-only | current | MPLS Label received for this destination from the peer |
| 1.3.6.1.4.1.10876.101.2.77.21.1.23 | ColumnfsMIBgp4mpebgp4PathAttrAS4PathSegment | read-only | current | The sequence of AS path segments. Each AS path segment is represented by a triple <type, length, value>. The type is a 1-octet field which has two possible val… |
| 1.3.6.1.4.1.10876.101.2.77.21.1.24 | ColumnfsMIBgp4mpebgp4PathAttrAggregatorAS4 | read-only | current | The 4 Byte AS number of the last BGP4 speaker that performed route aggregation. A value of zero (0) indicates the absence of this attribute. |
| 1.3.6.1.4.1.10876.101.2.77.22 | TablefsMIBgp4MpePeerExtTable | not-accessible | current | BGP Peer Extension Table. The entries in the table specifies the additional features supported for a peer by futureBGP4 Speaker in addition to the features spe… |
| 1.3.6.1.4.1.10876.101.2.77.22.1 | RowfsMIBgp4MpePeerExtEntry | not-accessible | current | Entry containing information about the additional features supported for a peer by futureBGP4 Speaker. |
| 1.3.6.1.4.1.10876.101.2.77.22.1.1 | ColumnfsMIBgp4mpePeerExtPeerType | not-accessible | current | The Type of the remote peer |
| 1.3.6.1.4.1.10876.101.2.77.22.1.2 | ColumnfsMIBgp4mpePeerExtPeerRemoteAddr | not-accessible | current | The remote IP address of this entry's BGP peer. |
| 1.3.6.1.4.1.10876.101.2.77.22.1.3 | ColumnfsMIBgp4mpePeerExtConfigurePeer | read-write | current | This object is used to create or delete a peer. If called with create and no matching peer exists, then a new peer entry will be created. The admin status of t… |
| 1.3.6.1.4.1.10876.101.2.77.22.1.4 | ColumnfsMIBgp4mpePeerExtPeerRemoteAs | read-write | current | The remote autonomous system number of the Peer. The peer admin status can be made up only if this object is configured for a valid AS number. When OPEN messag… |
| 1.3.6.1.4.1.10876.101.2.77.22.1.5 | ColumnfsMIBgp4mpePeerExtEBGPMultiHop | read-write | current | This objects enables the BGP4 Speaker to accept or attempt connections to external peers residing on network that are not directly connected. By default, only … |
| 1.3.6.1.4.1.10876.101.2.77.22.1.6 | ColumnfsMIBgp4mpePeerExtEBGPHopLimit | read-write | current | This objects enables the BGP4 Speaker to accept or attempt connections to external peers residing on network that are not directly connected and seperated by a… |
| 1.3.6.1.4.1.10876.101.2.77.22.1.7 | ColumnfsMIBgp4mpePeerExtNextHopSelf | read-write | current | This object specifies how the next hop attribute sent in the update messages to this peer has to be generated. When the object takes the value of self,the next… |
| 1.3.6.1.4.1.10876.101.2.77.22.1.8 | ColumnfsMIBgp4mpePeerExtRflClient | read-write | current | This object specifies whether the peer is Client peer or Non-Client peer. By default, the peer is created as Non-Client Peer. |
| 1.3.6.1.4.1.10876.101.2.77.22.1.9 | ColumnfsMIBgp4mpePeerExtTcpSendBufSize | read-write | current | This object configures the tcp window size on the sender side. |
| 1.3.6.1.4.1.10876.101.2.77.22.1.10 | ColumnfsMIBgp4mpePeerExtTcpRcvBufSize | read-write | current | This object configures the tcp window size on the receiver side. |
| 1.3.6.1.4.1.10876.101.2.77.22.1.11 | ColumnfsMIBgp4mpePeerExtLclAddress | read-write | current | This object specifies which address should be used as the source address of the TCP session initiated with the Peer. By default this object takes value as 0 an… |
| 1.3.6.1.4.1.10876.101.2.77.22.1.12 | ColumnfsMIBgp4mpePeerExtNetworkAddress | read-write | current | This object specifies the remote peer's network address. TCP connection is established using the peer's remote-address. If the peer's remote-address is a IPv4 … |
| 1.3.6.1.4.1.10876.101.2.77.22.1.13 | ColumnfsMIBgp4mpePeerExtGateway | read-write | current | This object specifies the gateway router's address that will be used as nexthop in the routes advertised to the peer. This ensures that the traffic coming from… |
| 1.3.6.1.4.1.10876.101.2.77.22.1.14 | ColumnfsMIBgp4mpePeerExtCommSendStatus | read-create | current | Community Send status of the peer. o none - is for read-only o send - send communities to this peer o donotsend - do not send communities to this peer. |
| 1.3.6.1.4.1.10876.101.2.77.22.1.15 | ColumnfsMIBgp4mpePeerExtECommSendStatus | read-create | current | Extended Community Send status of the peer. o none - is for read-only o send - send extended communities to this peer o donotsend - do not send extended commun… |
| 1.3.6.1.4.1.10876.101.2.77.22.1.16 | ColumnfsMIBgp4mpePeerExtPassive | read-write | current | This object is used to set a peer connection to be passive, that means the speaker will not initiate the session with that peer instead it waits for the remote… |
| 1.3.6.1.4.1.10876.101.2.77.22.1.17 | ColumnfsMIBgp4mpePeerExtDefaultOriginate | read-write | current | If this object is set to enable/disable the advertisement of the default route to the peer. This object overrides the global default route configuration (fsMIB… |
| 1.3.6.1.4.1.10876.101.2.77.23 | TablefsMIBgp4MpeMEDTable | not-accessible | current | BGP4 MED table. This table contains the MED values that are to be assigned to routes. |
| 1.3.6.1.4.1.10876.101.2.77.23.1 | RowfsMIBgp4MpeMEDEntry | not-accessible | current | Entry containing information about the MED value. |
| 1.3.6.1.4.1.10876.101.2.77.23.1.1 | ColumnfsMIBgp4mpeMEDIndex | not-accessible | current | This is the index to the table. Any entry in the table can be configured only if fsMIBgp4LocalAs is set. |
| 1.3.6.1.4.1.10876.101.2.77.23.1.2 | ColumnfsMIBgp4mpeMEDAdminStatus | read-write | current | The desired state of this entry. The entries in a row are configurable only if the admin status is DOWN. |
| 1.3.6.1.4.1.10876.101.2.77.23.1.3 | ColumnfsMIBgp4mpeMEDRemoteAS | read-write | current | The remote autonomous system with which this entry is associated. A value of zero indicates that this entry is not valid and will not be matched for when the M… |
| 1.3.6.1.4.1.10876.101.2.77.23.1.4 | ColumnfsMIBgp4mpeMEDIPAddrAfi | read-write | current | Type of IP address prefix in the Network Layer Reachability Information field in updates. This field needs to be set before setting the object fsMIBgp4mpeMEDIP… |
| 1.3.6.1.4.1.10876.101.2.77.23.1.5 | ColumnfsMIBgp4mpeMEDIPAddrSafi | read-write | current | Type of IP address prefix in the Network Layer Reachability Information field in updates. This field needs to be set before setting the object fsMIBgp4mpeMEDIP… |
| 1.3.6.1.4.1.10876.101.2.77.23.1.6 | ColumnfsMIBgp4mpeMEDIPAddrPrefix | read-write | current | An IP address prefix in the Network Layer Reachability Information field in updates. A value of zero indicates that the entry is not valid and will not be matc… |
| 1.3.6.1.4.1.10876.101.2.77.23.1.7 | ColumnfsMIBgp4mpeMEDIPAddrPrefixLen | read-write | current | Length in bits of the IP address prefix in the Network Layer Reachability Information field. A value of zero indicates that the entry is not valid and will not… |
| 1.3.6.1.4.1.10876.101.2.77.23.1.8 | ColumnfsMIBgp4mpeMEDIntermediateAS | read-write | current | Comma seperated list of AS numbers that are to be checked against the AS_PATH attribute of the Update. An empty field indicates that the same need not be check… |
| 1.3.6.1.4.1.10876.101.2.77.23.1.9 | ColumnfsMIBgp4mpeMEDDirection | read-write | current | The direction of the update with which the entry is to be associated. |
| 1.3.6.1.4.1.10876.101.2.77.23.1.10 | ColumnfsMIBgp4mpeMEDValue | read-write | current | The value assigned to the MED Attribute for the route present in NLRI |
| 1.3.6.1.4.1.10876.101.2.77.23.1.11 | ColumnfsMIBgp4mpeMEDPreference | read-write | current | This object specifies whether the value present in this entry takes precedence when the attribute is already present in the update message that has been receiv… |
| 1.3.6.1.4.1.10876.101.2.77.23.1.12 | ColumnfsMIBgp4mpeMEDVrfName | read-write | current | The human-readable name of the VPN. |
| 1.3.6.1.4.1.10876.101.2.77.24 | TablefsMIBgp4MpeLocalPrefTable | not-accessible | current | BGP Local Preference table. This table contains, the value that is to be assigned to the Local Preference attibute. |
| 1.3.6.1.4.1.10876.101.2.77.24.1 | RowfsMIBgp4MpeLocalPrefEntry | not-accessible | current | Entry containing information about the connection with a BGP peer. |
| 1.3.6.1.4.1.10876.101.2.77.24.1.1 | ColumnfsMIBgp4mpeLocalPrefIndex | not-accessible | current | This is the index to the table. Any entry in the table can be configured only if fsMIBgp4mpeLocalAs is set. |
| 1.3.6.1.4.1.10876.101.2.77.24.1.2 | ColumnfsMIBgp4mpeLocalPrefAdminStatus | read-write | current | The desired state of this entry. The entries in a row are configurable only if the admin status is DOWN. |
| 1.3.6.1.4.1.10876.101.2.77.24.1.3 | ColumnfsMIBgp4mpeLocalPrefRemoteAS | read-write | current | The remote autonomous system with which this entry is associated. A value of zero indicates that this entry is not valid and will not be matched for when the L… |
| 1.3.6.1.4.1.10876.101.2.77.24.1.4 | ColumnfsMIBgp4mpeLocalPrefIPAddrAfi | read-write | current | Type of IP address prefix in the Network Layer Reachability Information field. This field needs to be set before setting the object fsMIBgp4mpeLocalPrefIPAddrP… |
| 1.3.6.1.4.1.10876.101.2.77.24.1.5 | ColumnfsMIBgp4mpeLocalPrefIPAddrSafi | read-write | current | Sub-sequent address family of IP address prefix in the Network Layer Reachability Information field.This field needs to be set before setting the object fsMIBg… |
| 1.3.6.1.4.1.10876.101.2.77.24.1.6 | ColumnfsMIBgp4mpeLocalPrefIPAddrPrefix | read-write | current | An IP address prefix in the Network Layer Reachability Information field. A value of zero indicates that the entry is not valid and will not be matched for whe… |
| 1.3.6.1.4.1.10876.101.2.77.24.1.7 | ColumnfsMIBgp4mpeLocalPrefIPAddrPrefixLen | read-write | current | Length in bits of the IP address prefix in the Network Layer Reachability Information field. A value of zero indicates that the entry is not valid and will not… |
| 1.3.6.1.4.1.10876.101.2.77.24.1.8 | ColumnfsMIBgp4mpeLocalPrefIntermediateAS | read-write | current | Comma separated list of AS numbers that are to be present in the AS_PATH attribute of the Update. An empty field indicates that the same need not be checked fo… |
| 1.3.6.1.4.1.10876.101.2.77.24.1.9 | ColumnfsMIBgp4mpeLocalPrefDirection | read-write | current | The direction of the update with which the entry is to be associated. |
| 1.3.6.1.4.1.10876.101.2.77.24.1.10 | ColumnfsMIBgp4mpeLocalPrefValue | read-write | current | The value assigned to the LP Attribute for the route present in NLRI |
| 1.3.6.1.4.1.10876.101.2.77.24.1.11 | ColumnfsMIBgp4mpeLocalPrefPreference | read-write | current | This object specifies whether the value present in this entry takes precedence when the attribute is already present in the update message that has been receiv… |
| 1.3.6.1.4.1.10876.101.2.77.24.1.12 | ColumnfsMIBgp4mpeLocalPrefVrfName | read-write | current | The human-readable name of the VPN. |
| 1.3.6.1.4.1.10876.101.2.77.25 | TablefsMIBgp4MpeUpdateFilterTable | not-accessible | current | BGP Update Filter Table. This table contains Rules to filter out updates based on the AS from which it is received, NLRI and AS through which it had passed. |
| 1.3.6.1.4.1.10876.101.2.77.25.1 | RowfsMIBgp4MpeUpdateFilterEntry | not-accessible | current | Entry containing information about the updates that are to be filtered. |
| 1.3.6.1.4.1.10876.101.2.77.25.1.1 | ColumnfsMIBgp4mpeUpdateFilterIndex | not-accessible | current | This is the index to the table. Any entry in the table can be configured only if fsMIBgp4LocalAs is set. |
| 1.3.6.1.4.1.10876.101.2.77.25.1.2 | ColumnfsMIBgp4mpeUpdateFilterAdminStatus | read-write | current | The desired state of this entry. The entries in a row are configurable only if the admin status is DOWN. |
| 1.3.6.1.4.1.10876.101.2.77.25.1.3 | ColumnfsMIBgp4mpeUpdateFilterRemoteAS | read-write | current | The remote autonomous system with which this entry is associated. A value of zero indicates that this entry is not valid and will not be matched for when the u… |
| 1.3.6.1.4.1.10876.101.2.77.25.1.4 | ColumnfsMIBgp4mpeUpdateFilterIPAddrAfi | read-write | current | Type of IP address prefix in the Network Layer Reachability Information field. This field needs to be set, before setting the object fsMIBgp4mpeUpdateFilterIPA… |
| 1.3.6.1.4.1.10876.101.2.77.25.1.5 | ColumnfsMIBgp4mpeUpdateFilterIPAddrSafi | read-write | current | SAFI of IP address prefix in the Network Layer Reachability Information field. This field needs to be set, before setting the object fsMIBgp4mpeUpdateFilterIPA… |
| 1.3.6.1.4.1.10876.101.2.77.25.1.6 | ColumnfsMIBgp4mpeUpdateFilterIPAddrPrefix | read-write | current | An IP address prefix in the Network Layer Reachability Information field. A value of zero in this field indicates that the NLRI field may not be matched. |
| 1.3.6.1.4.1.10876.101.2.77.25.1.7 | ColumnfsMIBgp4mpeUpdateFilterIPAddrPrefixLen | read-write | current | Length in bits of the IP address prefix in the Network Layer Reachability Information field. A value of zero in this field indicates that the NLRI field may no… |
| 1.3.6.1.4.1.10876.101.2.77.25.1.8 | ColumnfsMIBgp4mpeUpdateFilterIntermediateAS | read-write | current | Comma separated list of AS numbers that are to be present in the AS_PATH attribute of the Update. An empty field indicates that the same need not be checked fo… |
| 1.3.6.1.4.1.10876.101.2.77.25.1.9 | ColumnfsMIBgp4mpeUpdateFilterDirection | read-write | current | The direction of the update with which the entry is to be associated. |
| 1.3.6.1.4.1.10876.101.2.77.25.1.10 | ColumnfsMIBgp4mpeUpdateFilterAction | read-write | current | The action to be taken when the characteristics that are specified in the entry is matched. |
| 1.3.6.1.4.1.10876.101.2.77.25.1.11 | ColumnfsMIBgp4mpeUpdateFilterVrfName | read-write | current | The human-readable name of the VPN. |
| 1.3.6.1.4.1.10876.101.2.77.26 | TablefsMIBgp4MpeAggregateTable | not-accessible | current | BGP Aggregate Table. The entries in the table specifies the IP address based on which the routing information has to be aggregated. |
| 1.3.6.1.4.1.10876.101.2.77.26.1 | RowfsMIBgp4MpeAggregateEntry | not-accessible | current | Entry containing information about the IP address on which the aggregation has to be done. |
| 1.3.6.1.4.1.10876.101.2.77.26.1.1 | ColumnfsMIBgp4mpeAggregateIndex | not-accessible | current | This is the index to the table.Any entry in the table can be configured only if fsMIBgp4LocalAs is set. |
| 1.3.6.1.4.1.10876.101.2.77.26.1.2 | ColumnfsMIBgp4mpeAggregateAdminStatus | read-write | current | The desired state of this entry. When the adminstatus is set to up, the aggregate entry will be made active and the aggregate route will be formed for this ent… |
| 1.3.6.1.4.1.10876.101.2.77.26.1.3 | ColumnfsMIBgp4mpeAggregateIPAddrAfi | read-write | current | Type of IP address prefix in the Network Layer Reachability Information field. This field needs to be set before setting the object fsMIBgp4mpeAggregateIPAddrP… |
| 1.3.6.1.4.1.10876.101.2.77.26.1.4 | ColumnfsMIBgp4mpeAggregateIPAddrSafi | read-write | current | SAFI of IP address prefix in the Network Layer Reachability Information field. This field needs to be set before setting the object fsMIBgp4mpeAggregateIPAddrP… |
| 1.3.6.1.4.1.10876.101.2.77.26.1.5 | ColumnfsMIBgp4mpeAggregateIPAddrPrefix | read-write | current | An IP address prefix in the Network Layer Reachability Information field. This field is configurable only if the admin status is DOWN |
| 1.3.6.1.4.1.10876.101.2.77.26.1.6 | ColumnfsMIBgp4mpeAggregateIPAddrPrefixLen | read-write | current | Length in bits of the IP address prefix in the Network Layer Reachability Information field. This field is configurable only if the admin status is DOWN. |
| 1.3.6.1.4.1.10876.101.2.77.26.1.7 | ColumnfsMIBgp4mpeAggregateAdvertise | read-write | current | This object specifies the route update that should be sent to the peers - summary-only - specifies that only the summarized route has to be advertised to peers… |
| 1.3.6.1.4.1.10876.101.2.77.26.1.8 | ColumnfsMIBgp4mpeAggregateVrfName | read-write | current | The human-readable name of the VPN. |
| 1.3.6.1.4.1.10876.101.2.77.26.1.9 | ColumnfsMIBgp4mpeAggregateAsSet | read-write | current | Enables/Disables the autonomous system set path information. It is an optional parameter |
| 1.3.6.1.4.1.10876.101.2.77.26.1.10 | ColumnfsMIBgp4mpeAggregateAdvertiseRouteMapName | read-write | current | The human-readable name for adverise route-map. The route map contains the rules for advertising the routes while aggregation. When we use advertise-map, only … |
| 1.3.6.1.4.1.10876.101.2.77.26.1.11 | ColumnfsMIBgp4mpeAggregateSuppressRouteMapName | read-write | current | The human-readable name for suppress route-map. The route map contains the rules for suppressing the routes while aggregation. when we use suppress-map configu… |
| 1.3.6.1.4.1.10876.101.2.77.26.1.12 | ColumnfsMIBgp4mpeAggregateAttributeRouteMapName | read-write | current | The human-readable name for attribute route-map. The route map contains the rules for setting the attributes the aggregated route. When attribute-map and adver… |
| 1.3.6.1.4.1.10876.101.2.77.27 | TablefsMIBgp4MpeImportRouteTable | not-accessible | current | Non-BGP routes imported into the BGP RIB can be viewed through this table. Also allows importing a static route into BGP.After updating the RIB tree, if there … |
| 1.3.6.1.4.1.10876.101.2.77.27.1 | RowfsMIBgp4MpeImportRouteEntry | not-accessible | current | Import Route entry. |
| 1.3.6.1.4.1.10876.101.2.77.27.1.1 | ColumnfsMIBgp4mpeImportRoutePrefixAfi | not-accessible | current | Type of Prefix of the route to be imported. |
| 1.3.6.1.4.1.10876.101.2.77.27.1.2 | ColumnfsMIBgp4mpeImportRoutePrefixSafi | not-accessible | current | SAFI of Prefix of the route to be imported. Only UNICAST (1) is allowed right now. Route can be imported into VRF by providing SAFI (1) and VRF name. |
| 1.3.6.1.4.1.10876.101.2.77.27.1.3 | ColumnfsMIBgp4mpeImportRoutePrefix | not-accessible | current | Prefix of the route to be imported. |
| 1.3.6.1.4.1.10876.101.2.77.27.1.4 | ColumnfsMIBgp4mpeImportRoutePrefixLen | not-accessible | current | Prefix length of the route. |
| 1.3.6.1.4.1.10876.101.2.77.27.1.5 | ColumnfsMIBgp4mpeImportRouteProtocol | not-accessible | current | Protocol value for Non-BGP routes. 2- LOCAL, 3 - STATIC, 8 - RIP, 13 - OSPF. Only STATIC routes (protocol 3) can be added through this table. However all non-B… |
| 1.3.6.1.4.1.10876.101.2.77.27.1.6 | ColumnfsMIBgp4mpeImportRouteNextHop | not-accessible | current | NextHop Ipaddress for the route. |
| 1.3.6.1.4.1.10876.101.2.77.27.1.7 | ColumnfsMIBgp4mpeImportRouteIfIndex | not-accessible | current | Interface Index of the Route |
| 1.3.6.1.4.1.10876.101.2.77.27.1.8 | ColumnfsMIBgp4mpeImportRouteMetric | not-accessible | current | Metric for the route being imported. |
| 1.3.6.1.4.1.10876.101.2.77.27.1.9 | ColumnfsMIBgp4mpeImportRouteVrf | not-accessible | current | Vrf in which the route should be imported. If the rotueis to be installed in default VRF, the value should be NULL string |
| 1.3.6.1.4.1.10876.101.2.77.27.1.10 | ColumnfsMIBgp4mpeImportRouteAction | read-write | current | Controls addition or deletion of route. |
| 1.3.6.1.4.1.10876.101.2.77.28 | TablefsMIBgp4MpeFsmTransitionHistTable | not-accessible | current | Gets FSM transitions history per peer |
| 1.3.6.1.4.1.10876.101.2.77.28.1 | RowfsMIBgp4MpeFsmTransitionHistEntry | not-accessible | current | Fsm Hist entry. |
| 1.3.6.1.4.1.10876.101.2.77.28.1.1 | ColumnfsMIBgp4mpePeerType | not-accessible | current | Type of Peer from which FSM transition history would be read. |
| 1.3.6.1.4.1.10876.101.2.77.28.1.2 | ColumnfsMIBgp4mpePeer | not-accessible | current | Peer from which FSM transition history would be read. |
| 1.3.6.1.4.1.10876.101.2.77.28.1.3 | ColumnfsMIBgp4mpeFsmTransitionHist | read-only | current | sequence of FSM states separated by space |
| 1.3.6.1.4.1.10876.101.2.77.29 | NodefsMIBgp4MpeRfd | |||
| 1.3.6.1.4.1.10876.101.2.77.29.1 | TablefsMIBgp4MpeRfdRtDampHistTable | not-accessible | current | Route damping history table.This table contains the figure-of-merit and the route status |
| 1.3.6.1.4.1.10876.101.2.77.29.1.1 | RowfsMIBgp4MpeRfdRtDampHistEntry | not-accessible | current | Entry contains route damping history |
| 1.3.6.1.4.1.10876.101.2.77.29.1.1.1 | ColumnfsMIBgp4mpePathAttrAddrPrefixAfi | not-accessible | current | AFI of the route |
| 1.3.6.1.4.1.10876.101.2.77.29.1.1.2 | ColumnfsMIBgp4mpePathAttrAddrPrefixSafi | not-accessible | current | SAFI of the route |
| 1.3.6.1.4.1.10876.101.2.77.29.1.1.3 | ColumnfsMIBgp4mpePathAttrAddrPrefix | not-accessible | current | An IP address prefix in the NLRI field. This object is an IP address containing the prefix with the length specified by fsMIBgp4mpePathAttrAddrPrefixLen. Any b… |
| 1.3.6.1.4.1.10876.101.2.77.29.1.1.4 | ColumnfsMIBgp4mpePathAttrAddrPrefixLen | not-accessible | current | Length in bits of the IP address prefix in NLRI field. |
| 1.3.6.1.4.1.10876.101.2.77.29.1.1.5 | ColumnfsMIBgp4mpePathAttrPeerType | not-accessible | current | AFI of the peer |
| 1.3.6.1.4.1.10876.101.2.77.29.1.1.6 | ColumnfsMIBgp4mpePathAttrPeer | not-accessible | current | The Peer remote address of the peer where the path information was learned. |
| 1.3.6.1.4.1.10876.101.2.77.29.1.1.7 | ColumnfsMIBgp4mpeRfdRtFom | read-only | current | The figure-of-merit of the route |
| 1.3.6.1.4.1.10876.101.2.77.29.1.1.8 | ColumnfsMIBgp4mpeRfdRtLastUpdtTime | read-only | current | The time when the route figure-of-merit was updated. |
| 1.3.6.1.4.1.10876.101.2.77.29.1.1.9 | ColumnfsMIBgp4mpeRfdRtState | read-only | current | The value gives the status whether the route is suppressed or not |
| 1.3.6.1.4.1.10876.101.2.77.29.1.1.10 | ColumnfsMIBgp4mpeRfdRtStatus | read-only | current | The value gives the status whether the route is feasible or unfeasible route |
| 1.3.6.1.4.1.10876.101.2.77.29.1.1.11 | ColumnfsMIBgp4mpeRfdRtFlapCount | read-only | current | This value gives the number of times the route being flapped |
| 1.3.6.1.4.1.10876.101.2.77.29.1.1.12 | ColumnfsMIBgp4mpeRfdRtFlapTime | read-only | current | The time calculated for a route, from when a route is being flapped for first time, time in seconds |
| 1.3.6.1.4.1.10876.101.2.77.29.1.1.13 | ColumnfsMIBgp4mpeRfdRtReuseTime | read-only | current | The time after which a route can be reused again after it moves to suppressed state from unsuppressed state, time in seconds |
| 1.3.6.1.4.1.10876.101.2.77.29.2 | TablefsMIBgp4MpeRfdPeerDampHistTable | not-accessible | current | Peer Damping history table. It contains the peer figure-of-merit and peer status. |
| 1.3.6.1.4.1.10876.101.2.77.29.2.1 | RowfsMIBgp4MpeRfdPeerDampHistEntry | not-accessible | current | Entry contains peer damping history |
| 1.3.6.1.4.1.10876.101.2.77.29.2.1.1 | ColumnfsMIBgp4mpePeerRemoteIpAddrType | not-accessible | current | AFI of the remote peer |
| 1.3.6.1.4.1.10876.101.2.77.29.2.1.2 | ColumnfsMIBgp4mpePeerRemoteIpAddr | not-accessible | current | The peer remote address of the peer. |
| 1.3.6.1.4.1.10876.101.2.77.29.2.1.3 | ColumnfsMIBgp4mpeRfdPeerFom | read-only | current | The current figure-of-merit of peer |
| 1.3.6.1.4.1.10876.101.2.77.29.2.1.4 | ColumnfsMIBgp4mpeRfdPeerLastUpdtTime | read-only | current | The time when the figure-of-merit was updated. |
| 1.3.6.1.4.1.10876.101.2.77.29.2.1.5 | ColumnfsMIBgp4mpeRfdPeerState | read-only | current | This value gives the status whether peer is suppressed or not |
| 1.3.6.1.4.1.10876.101.2.77.29.2.1.6 | ColumnfsMIBgp4mpeRfdPeerStatus | read-only | current | This value gives the status whether peer is up or down |
| 1.3.6.1.4.1.10876.101.2.77.29.3 | TablefsMIBgp4MpeRfdRtsReuseListTable | not-accessible | current | Routes Reuse List Table. It contains the IP prefix and prefix length. |
| 1.3.6.1.4.1.10876.101.2.77.29.3.1 | RowfsMIBgp4MpeRfdRtsReuseListEntry | not-accessible | current | Entry contains routes reuse list |
| 1.3.6.1.4.1.10876.101.2.77.29.3.1.1 | ColumnfsMIBgp4mpeRtAfi | not-accessible | current | AFI of the route |
| 1.3.6.1.4.1.10876.101.2.77.29.3.1.2 | ColumnfsMIBgp4mpeRtSafi | not-accessible | current | AFI of the route |
| 1.3.6.1.4.1.10876.101.2.77.29.3.1.3 | ColumnfsMIBgp4mpeRtIPPrefix | not-accessible | current | An IP address prefix in the NLRI field. This object is an IP address containing the prefix with the length specified by fsMIBgp4RtIPPrefixLen. Any bits beyond … |
| 1.3.6.1.4.1.10876.101.2.77.29.3.1.4 | ColumnfsMIBgp4mpeRtIPPrefixLen | not-accessible | current | Length in bits of the IP address prefix in NLRI field. |
| 1.3.6.1.4.1.10876.101.2.77.29.3.1.5 | ColumnfsMIBgp4mpeRfdRtsReusePeerType | not-accessible | current | AFI of the remote peer |
| 1.3.6.1.4.1.10876.101.2.77.29.3.1.6 | ColumnfsMIBgp4mpePeerRemAddress | not-accessible | current | The Peer remote address of the peer where the path information was learned. |
| 1.3.6.1.4.1.10876.101.2.77.29.3.1.7 | ColumnfsMIBgp4mpeRfdRtReuseListRtFom | read-only | current | The figure-of-merit of the route which is in the routes reuse list |
| 1.3.6.1.4.1.10876.101.2.77.29.3.1.8 | ColumnfsMIBgp4mpeRfdRtReuseListRtLastUpdtTime | read-only | current | The time when the route figure-of-merit was updated. |
| 1.3.6.1.4.1.10876.101.2.77.29.3.1.9 | ColumnfsMIBgp4mpeRfdRtReuseListRtState | read-only | current | The value gives the status whether the route is suppressed or not |
| 1.3.6.1.4.1.10876.101.2.77.29.3.1.10 | ColumnfsMIBgp4mpeRfdRtReuseListRtStatus | read-only | current | The value gives the status whether the route is feasible or unfeasible route |
| 1.3.6.1.4.1.10876.101.2.77.29.4 | TablefsMIBgp4MpeRfdPeerReuseListTable | not-accessible | current | Peer's Reuse List Table. It contains the Peer Remote Address. |
| 1.3.6.1.4.1.10876.101.2.77.29.4.1 | RowfsMIBgp4MpeRfdPeerReuseListEntry | not-accessible | current | Entry contains routes reuse list |
| 1.3.6.1.4.1.10876.101.2.77.29.4.1.1 | ColumnfsMIBgp4mpeRfdPeerRemIpAddrType | not-accessible | current | AFI of the peer |
| 1.3.6.1.4.1.10876.101.2.77.29.4.1.2 | ColumnfsMIBgp4mpeRfdPeerRemIpAddr | not-accessible | current | The peer remote address of the peer which is in the peer's reuse list. |
| 1.3.6.1.4.1.10876.101.2.77.29.4.1.3 | ColumnfsMIBgp4mpeRfdPeerReuseListPeerFom | read-only | current | The current figure-of-merit of peer |
| 1.3.6.1.4.1.10876.101.2.77.29.4.1.4 | ColumnfsMIBgp4mpeRfdPeerReuseListLastUpdtTime | read-only | current | The time when the figure-of-merit was updated. |
| 1.3.6.1.4.1.10876.101.2.77.29.4.1.5 | ColumnfsMIBgp4mpeRfdPeerReuseListPeerState | read-only | current | This value gives the status whether peer is suppressed or not |
| 1.3.6.1.4.1.10876.101.2.77.29.4.1.6 | ColumnfsMIBgp4mpeRfdPeerReuseListPeerStatus | read-only | current | This value gives the status whether peer is up or down |
| 1.3.6.1.4.1.10876.101.2.77.30 | NodefsMIBgp4MpeComm | |||
| 1.3.6.1.4.1.10876.101.2.77.30.1 | TablefsMIBgp4MpeCommRouteAddCommTable | not-accessible | current | This table is used to configure additive communities for a given destination. |
| 1.3.6.1.4.1.10876.101.2.77.30.1.1 | RowfsMIBgp4MpeCommRouteAddCommEntry | not-accessible | current | Routes configured additive communities Table Entry |
| 1.3.6.1.4.1.10876.101.2.77.30.1.1.1 | ColumnfsMIBgp4mpeAddCommRtAfi | not-accessible | current | AFI of IP address of the destination |
| 1.3.6.1.4.1.10876.101.2.77.30.1.1.2 | ColumnfsMIBgp4mpeAddCommRtSafi | not-accessible | current | SAFI of IP address of the destination |
| 1.3.6.1.4.1.10876.101.2.77.30.1.1.3 | ColumnfsMIBgp4mpeAddCommIpNetwork | not-accessible | current | IP address of the destination |
| 1.3.6.1.4.1.10876.101.2.77.30.1.1.4 | ColumnfsMIBgp4mpeAddCommIpPrefixLen | not-accessible | current | IP prefix length for the destination |
| 1.3.6.1.4.1.10876.101.2.77.30.1.1.5 | ColumnfsMIBgp4mpeAddCommVal | not-accessible | current | Additive Community configured for the Route |
| 1.3.6.1.4.1.10876.101.2.77.30.1.1.6 | ColumnfsMIBgp4mpeAddCommRowStatus | read-create | current | Row status for creating entries into this table.This object can be set only if fsMIBgp4LocalAS is configured. |
| 1.3.6.1.4.1.10876.101.2.77.30.2 | TablefsMIBgp4MpeCommRouteDeleteCommTable | not-accessible | current | This table is used to configure delete communities for a given destination. |
| 1.3.6.1.4.1.10876.101.2.77.30.2.1 | RowfsMIBgp4MpeCommRouteDeleteCommEntry | not-accessible | current | Routes configured delete communities Table Entry |
| 1.3.6.1.4.1.10876.101.2.77.30.2.1.1 | ColumnfsMIBgp4mpeDeleteCommRtAfi | not-accessible | current | AFI of IP address of the destination |
| 1.3.6.1.4.1.10876.101.2.77.30.2.1.2 | ColumnfsMIBgp4mpeDeleteCommRtSafi | not-accessible | current | SAFI of IP address of the destination |
| 1.3.6.1.4.1.10876.101.2.77.30.2.1.3 | ColumnfsMIBgp4mpeDeleteCommIpNetwork | not-accessible | current | IP address of the destination |
| 1.3.6.1.4.1.10876.101.2.77.30.2.1.4 | ColumnfsMIBgp4mpeDeleteCommIpPrefixLen | not-accessible | current | IP prefix length for the destination |
| 1.3.6.1.4.1.10876.101.2.77.30.2.1.5 | ColumnfsMIBgp4mpeDeleteCommVal | not-accessible | current | Delete Community configured for the Route |
| 1.3.6.1.4.1.10876.101.2.77.30.2.1.6 | ColumnfsMIBgp4mpeDeleteCommRowStatus | read-create | current | Row status for creating entries into this table.This object can be set only if fsMIBgp4LocalAS is configured. |
| 1.3.6.1.4.1.10876.101.2.77.30.3 | TablefsMIBgp4MpeCommRouteCommSetStatusTable | not-accessible | current | This table is used to configure the local policy of communities for a given destination. |
| 1.3.6.1.4.1.10876.101.2.77.30.3.1 | RowfsMIBgp4MpeCommRouteCommSetStatusEntry | not-accessible | current | Routes configured delete communities Table Entry |
| 1.3.6.1.4.1.10876.101.2.77.30.3.1.1 | ColumnfsMIBgp4mpeCommSetStatusAfi | not-accessible | current | AFI of IP address of the destination |
| 1.3.6.1.4.1.10876.101.2.77.30.3.1.2 | ColumnfsMIBgp4mpeCommSetStatusSafi | not-accessible | current | SAFI of IP address of the destination |
| 1.3.6.1.4.1.10876.101.2.77.30.3.1.3 | ColumnfsMIBgp4mpeCommSetStatusIpNetwork | not-accessible | current | IP address of the destination |
| 1.3.6.1.4.1.10876.101.2.77.30.3.1.4 | ColumnfsMIBgp4mpeCommSetStatusIpPrefixLen | not-accessible | current | IP prefix length for the destination |
| 1.3.6.1.4.1.10876.101.2.77.30.3.1.5 | ColumnfsMIBgp4mpeCommSetStatus | read-create | current | Community Set status for the Route. o none - is for read-only o set - to send only with configured additive communities o setnone - to send without communities… |
| 1.3.6.1.4.1.10876.101.2.77.30.3.1.6 | ColumnfsMIBgp4mpeCommSetStatusRowStatus | read-create | current | Row status for creating entries into this table. This object can be set only if fsMIBgp4LocalAs is configured. |
| 1.3.6.1.4.1.10876.101.2.77.31 | NodefsMIBgp4MpeExtComm | |||
| 1.3.6.1.4.1.10876.101.2.77.31.1 | TablefsMIBgp4MpeExtCommRouteAddExtCommTable | not-accessible | current | This table is used to configure additive extended communities for a given destination. |
| 1.3.6.1.4.1.10876.101.2.77.31.1.1 | RowfsMIBgp4MpeExtCommRouteAddExtCommEntry | not-accessible | current | Routes configured additive ext-communities Table Entry |
| 1.3.6.1.4.1.10876.101.2.77.31.1.1.1 | ColumnfsMIBgp4mpeAddExtCommRtAfi | not-accessible | current | AFI of IP address of the destination |
| 1.3.6.1.4.1.10876.101.2.77.31.1.1.2 | ColumnfsMIBgp4mpeAddExtCommRtSafi | not-accessible | current | AFI of IP address of the destination |
| 1.3.6.1.4.1.10876.101.2.77.31.1.1.3 | ColumnfsMIBgp4mpeAddExtCommIpNetwork | not-accessible | current | IP address of the destination |
| 1.3.6.1.4.1.10876.101.2.77.31.1.1.4 | ColumnfsMIBgp4mpeAddExtCommIpPrefixLen | not-accessible | current | IP prefix length for the destination |
| 1.3.6.1.4.1.10876.101.2.77.31.1.1.5 | ColumnfsMIBgp4mpeAddExtCommVal | not-accessible | current | Additive Ext-Community for the destination |
| 1.3.6.1.4.1.10876.101.2.77.31.1.1.6 | ColumnfsMIBgp4mpeAddExtCommRowStatus | read-create | current | Row status for creating entries into this table.This object can be set only if fsMIBgp4LocalAs is configured. |
| 1.3.6.1.4.1.10876.101.2.77.31.2 | TablefsMIBgp4MpeExtCommRouteDeleteExtCommTable | not-accessible | current | This table is used to configure delete extended communities for a given destination. |
| 1.3.6.1.4.1.10876.101.2.77.31.2.1 | RowfsMIBgp4MpeExtCommRouteDeleteExtCommEntry | not-accessible | current | Routes configured delete ext-communities Table Entry |
| 1.3.6.1.4.1.10876.101.2.77.31.2.1.1 | ColumnfsMIBgp4mpeDeleteExtCommRtAfi | not-accessible | current | AFI of IP address of the destination |
| 1.3.6.1.4.1.10876.101.2.77.31.2.1.2 | ColumnfsMIBgp4mpeDeleteExtCommRtSafi | not-accessible | current | SAFI of IP address of the destination |
| 1.3.6.1.4.1.10876.101.2.77.31.2.1.3 | ColumnfsMIBgp4mpeDeleteExtCommIpNetwork | not-accessible | current | IP address of the destination |
| 1.3.6.1.4.1.10876.101.2.77.31.2.1.4 | ColumnfsMIBgp4mpeDeleteExtCommIpPrefixLen | not-accessible | current | IP prefix length for the destination |
| 1.3.6.1.4.1.10876.101.2.77.31.2.1.5 | ColumnfsMIBgp4mpeDeleteExtCommVal | not-accessible | current | Delete Ext-Community for the destination |
| 1.3.6.1.4.1.10876.101.2.77.31.2.1.6 | ColumnfsMIBgp4mpeDeleteExtCommRowStatus | read-create | current | Row status to create entries into this table. This object can be set only if fsMIBgp4LocalAs is configured. |
| 1.3.6.1.4.1.10876.101.2.77.31.3 | TablefsMIBgp4MpeExtCommRouteExtCommSetStatusTable | not-accessible | current | This table is used to configure the local policy of extended communities for a given destination. |
| 1.3.6.1.4.1.10876.101.2.77.31.3.1 | RowfsMIBgp4MpeExtCommRouteExtCommSetStatusEntry | not-accessible | current | Routes configured delete ext-communities Table Entry |
| 1.3.6.1.4.1.10876.101.2.77.31.3.1.1 | ColumnfsMIBgp4mpeExtCommSetStatusRtAfi | not-accessible | current | AFI of IP address of the destination |
| 1.3.6.1.4.1.10876.101.2.77.31.3.1.2 | ColumnfsMIBgp4mpeExtCommSetStatusRtSafi | not-accessible | current | SAFI of IP address of the destination |
| 1.3.6.1.4.1.10876.101.2.77.31.3.1.3 | ColumnfsMIBgp4mpeExtCommSetStatusIpNetwork | not-accessible | current | IP address of the destination |
| 1.3.6.1.4.1.10876.101.2.77.31.3.1.4 | ColumnfsMIBgp4mpeExtCommSetStatusIpPrefixLen | not-accessible | current | IP prefix length of the destination |
| 1.3.6.1.4.1.10876.101.2.77.31.3.1.5 | ColumnfsMIBgp4mpeExtCommSetStatus | read-create | current | Ext-Community Set status for the Route. o none - is for read-only o set - to send only with configured additive ext-communities o setnone - to send without ext… |
| 1.3.6.1.4.1.10876.101.2.77.31.3.1.6 | ColumnfsMIBgp4mpeExtCommSetStatusRowStatus | read-create | current | Row status to create entries into this table. This object can be set only if fsMIBgp4LocalAs is configured. |
| 1.3.6.1.4.1.10876.101.2.77.31.4 | TablefsMIBgp4MpePeerLinkBwTable | not-accessible | current | This table is used to configure the link bandwidths for a given peer |
| 1.3.6.1.4.1.10876.101.2.77.31.4.1 | RowfsMIBgp4MpePeerLinkBwEntry | not-accessible | current | Peer Link Bandwidth Table Entry |
| 1.3.6.1.4.1.10876.101.2.77.31.4.1.1 | ColumnfsMIBgp4mpePeerLinkType | not-accessible | current | AFI of IP address of the Peer |
| 1.3.6.1.4.1.10876.101.2.77.31.4.1.2 | ColumnfsMIBgp4mpePeerLinkRemAddr | not-accessible | current | IP address of the Peer |
| 1.3.6.1.4.1.10876.101.2.77.31.4.1.3 | ColumnfsMIBgp4mpeLinkBandWidth | read-create | current | Link Bandwidth in bytes per second.This object can be set only if fsMIBgp4LocalAs is configured. |
| 1.3.6.1.4.1.10876.101.2.77.31.4.1.4 | ColumnfsMIBgp4mpePeerLinkBwRowStatus | read-create | current | Row Status to create entries into this table. This object can be set only if fsMIBgp4LocalAs is configured. |
| 1.3.6.1.4.1.10876.101.2.77.32 | NodefsMIBgp4MpeCaps | |||
| 1.3.6.1.4.1.10876.101.2.77.32.1 | TablefsMIBgp4MpeCapSupportedCapsTable | not-accessible | current | Supported Capabilities Table. This table contains, the capabilities that are supported for particular peer |
| 1.3.6.1.4.1.10876.101.2.77.32.1.1 | RowfsMIBgp4MpeCapSupportedCapsEntry | not-accessible | current | Entry contains supported Capabilites |
| 1.3.6.1.4.1.10876.101.2.77.32.1.1.1 | ColumnfsMIBgp4mpeCapPeerType | not-accessible | current | The remote IP Address of Peer |
| 1.3.6.1.4.1.10876.101.2.77.32.1.1.2 | ColumnfsMIBgp4mpeCapPeerRemoteIpAddr | not-accessible | current | The remote IP Address of Peer |
| 1.3.6.1.4.1.10876.101.2.77.32.1.1.3 | ColumnfsMIBgp4mpeSupportedCapabilityCode | not-accessible | current | BGP-4 Capability Advertisement Capability Code that is supported for peer. |
| 1.3.6.1.4.1.10876.101.2.77.32.1.1.4 | ColumnfsMIBgp4mpeSupportedCapabilityLength | not-accessible | current | The length of the supported Capability data. Currently the max size is set as 16. Update the BGP_MAX_CAP_DATA_SIZE in inc/system.size file or BGP_DEF_MAX_CAP_D… |
| 1.3.6.1.4.1.10876.101.2.77.32.1.1.5 | ColumnfsMIBgp4mpeSupportedCapabilityValue | not-accessible | current | The value of the supported Capability |
| 1.3.6.1.4.1.10876.101.2.77.32.1.1.6 | ColumnfsMIBgp4mpeCapSupportedCapsRowStatus | read-create | current | The variable displays the status of the entry.Setting it to 'invalid' has the effect of rendering it inoperative. |
| 1.3.6.1.4.1.10876.101.2.77.32.1.1.7 | ColumnfsMIBgp4mpeCapAnnouncedStatus | read-only | current | The variable displays the status whether the capability is announced to the peer or not. |
| 1.3.6.1.4.1.10876.101.2.77.32.1.1.8 | ColumnfsMIBgp4mpeCapReceivedStatus | read-only | current | The variable displays the status whether the capability is received from the peer or not. |
| 1.3.6.1.4.1.10876.101.2.77.32.1.1.9 | ColumnfsMIBgp4mpeCapNegotiatedStatus | read-only | current | The variable displays the status whether the capability is Negotiated to the peer or not. |
| 1.3.6.1.4.1.10876.101.2.77.32.1.1.10 | ColumnfsMIBgp4mpeCapConfiguredStatus | read-only | current | The variable displays the status whether the capability is enabled by default or through configuration |
| 1.3.6.1.4.1.10876.101.2.77.33 | NodefsMIBgp4MpeRtRefresh | |||
| 1.3.6.1.4.1.10876.101.2.77.33.1 | TablefsMIBgp4MpeRtRefreshInboundTable | not-accessible | current | Route Refresh Inbound Table |
| 1.3.6.1.4.1.10876.101.2.77.33.1.1 | RowfsMIBgp4MpeRtRefreshInboundEntry | not-accessible | current | Entry corresponds to Route Refresh Inbound. |
| 1.3.6.1.4.1.10876.101.2.77.33.1.1.1 | ColumnfsMIBgp4mpeRtRefreshInboundPeerType | not-accessible | current | Address Family Identifier of the peer remote address |
| 1.3.6.1.4.1.10876.101.2.77.33.1.1.2 | ColumnfsMIBgp4mpeRtRefreshInboundPeerAddr | not-accessible | current | The IP address of the peeri for which the Route Refresh request has to be issued. |
| 1.3.6.1.4.1.10876.101.2.77.33.1.1.3 | ColumnfsMIBgp4mpeRtRefreshInboundAfi | not-accessible | current | The AFI for which the Route-Refresh message is to be sent |
| 1.3.6.1.4.1.10876.101.2.77.33.1.1.4 | ColumnfsMIBgp4mpeRtRefreshInboundSafi | not-accessible | current | The SAFI for which the Route-Refresh message is to be sent |
| 1.3.6.1.4.1.10876.101.2.77.33.1.1.5 | ColumnfsMIBgp4mpeRtRefreshInboundRequest | read-write | current | Setting this object triggers the sending of the Route Refresh message to the peer. This object will be cleared once the Route Refresh message is sent to the pe… |
| 1.3.6.1.4.1.10876.101.2.77.33.1.1.6 | ColumnfsMIBgp4mpeRtRefreshInboundPrefixFilter | read-write | current | Setting this object triggers the sending of the ORF entris in the Route Refresh message to the peer. This object will be cleared once the ORF message is sent t… |
| 1.3.6.1.4.1.10876.101.2.77.33.2 | TablefsMIBgp4MpeRtRefreshStatisticsTable | not-accessible | current | Route Refresh Statistics Table |
| 1.3.6.1.4.1.10876.101.2.77.33.2.1 | RowfsMIBgp4MpeRtRefreshStatisticsEntry | not-accessible | current | Entry gives the statistics of Route Refresh. |
| 1.3.6.1.4.1.10876.101.2.77.33.2.1.1 | ColumnfsMIBgp4mpeRtRefreshStatisticsPeerType | not-accessible | current | Address Family Identifier of the peer remote address. |
| 1.3.6.1.4.1.10876.101.2.77.33.2.1.2 | ColumnfsMIBgp4mpeRtRefreshStatisticsPeerAddr | not-accessible | current | The IP address of the peer for which the Route Refresh Statistics has to be read. |
| 1.3.6.1.4.1.10876.101.2.77.33.2.1.3 | ColumnfsMIBgp4mpeRtRefreshStatisticsAfi | not-accessible | current | AFI for for which the Route Refresh Statistics has to be read. |
| 1.3.6.1.4.1.10876.101.2.77.33.2.1.4 | ColumnfsMIBgp4mpeRtRefreshStatisticsSafi | not-accessible | current | SAFI for for which the Route Refresh Statistics has to be read. |
| 1.3.6.1.4.1.10876.101.2.77.33.2.1.5 | ColumnfsMIBgp4mpeRtRefreshStatisticsRtRefMsgSentCntr | read-only | current | The number of Route Refresh messages sent to the peer. |
| 1.3.6.1.4.1.10876.101.2.77.33.2.1.6 | ColumnfsMIBgp4mpeRtRefreshStatisticsRtRefMsgTxErrCntr | read-only | current | The number of Route Refresh messages that could not be transmitted to the peer. |
| 1.3.6.1.4.1.10876.101.2.77.33.2.1.7 | ColumnfsMIBgp4mpeRtRefreshStatisticsRtRefMsgRcvdCntr | read-only | current | The number of Route Refresh messages received from the peer. |
| 1.3.6.1.4.1.10876.101.2.77.33.2.1.8 | ColumnfsMIBgp4mpeRtRefreshStatisticsRtRefMsgInvalidCntr | read-only | current | The number of invalid Route Refresh messages received from the peer. |
| 1.3.6.1.4.1.10876.101.2.77.34 | NodefsMIBgp4MpeSoftReconfigOut | |||
| 1.3.6.1.4.1.10876.101.2.77.34.1 | TablefsMIBgp4MpeSoftReconfigOutboundTable | not-accessible | current | Soft Reconfig outbound Table |
| 1.3.6.1.4.1.10876.101.2.77.34.1.1 | RowfsMIBgp4MpeSoftReconfigOutboundEntry | not-accessible | current | Entry corresponds to Soft Reconfig outbound. |
| 1.3.6.1.4.1.10876.101.2.77.34.1.1.1 | ColumnfsMIBgp4mpeSoftReconfigOutboundPeerType | not-accessible | current | Address Family Identifier of the peer remote address |
| 1.3.6.1.4.1.10876.101.2.77.34.1.1.2 | ColumnfsMIBgp4mpeSoftReconfigOutboundPeerAddr | not-accessible | current | The IP address of the peer for which the outbound soft-reconfig has to be performed. |
| 1.3.6.1.4.1.10876.101.2.77.34.1.1.3 | ColumnfsMIBgp4mpeSoftReconfigOutboundAfi | not-accessible | current | AFI for which the outbound soft-reconfig has to be performed. |
| 1.3.6.1.4.1.10876.101.2.77.34.1.1.4 | ColumnfsMIBgp4mpeSoftReconfigOutboundSafi | not-accessible | current | SAFI for which the outbound soft-reconfig has to be performed. |
| 1.3.6.1.4.1.10876.101.2.77.34.1.1.5 | ColumnfsMIBgp4mpeSoftReconfigOutboundRequest | read-write | current | Setting this object triggers the outbound soft-reconfig process for the peer. This object value is cleared once the soft-reconfig process is completed. |
| 1.3.6.1.4.1.10876.101.2.77.35 | TablefsMIBgp4MpePrefixCountersTable | not-accessible | current | Additional per-peer, per AFI/SAFI counters for prefixes |
| 1.3.6.1.4.1.10876.101.2.77.35.1 | RowfsMIBgp4MpePrefixCountersEntry | not-accessible | current | Entry containing information about a bgp-peer's prefix counters. |
| 1.3.6.1.4.1.10876.101.2.77.35.1.1 | ColumnfsMIBgp4MpePeerRemoteAddrType | not-accessible | current | The type of the remote address of peer. |
| 1.3.6.1.4.1.10876.101.2.77.35.1.2 | ColumnfsMIBgp4MpePeerRemoteAddr | not-accessible | current | The remote address of the peer. |
| 1.3.6.1.4.1.10876.101.2.77.35.1.3 | ColumnfsMIBgp4MpePrefixCountersAfi | not-accessible | current | The AFI index of the per-peer, per prefix counters |
| 1.3.6.1.4.1.10876.101.2.77.35.1.4 | ColumnfsMIBgp4MpePrefixCountersSafi | not-accessible | current | The SAFI index of the per-peer, per prefix counters |
| 1.3.6.1.4.1.10876.101.2.77.35.1.5 | ColumnfsMIBgp4MpePrefixCountersPrefixesReceived | read-only | current | Total number of discrete prefixes received from this peer. The value in fsMIBgp4MpePrefixCountersPrefixesReceived will be greater than or equal to what is in f… |
| 1.3.6.1.4.1.10876.101.2.77.35.1.6 | ColumnfsMIBgp4MpePrefixCountersPrefixesSent | read-only | current | Total number of prefixes which the local BGP speaker has announced to this peer. The value for fsMIBgp4MpePrefixCountersPrefixesSent will be greater than or eq… |
| 1.3.6.1.4.1.10876.101.2.77.35.1.7 | ColumnfsMIBgp4MpePrefixCountersWithdrawsReceived | read-only | current | Total number of prefixes withdrawn by this peer. Specifically, this is the total number of withdrawn-routes which have been received in UPDATE messages from th… |
| 1.3.6.1.4.1.10876.101.2.77.35.1.8 | ColumnfsMIBgp4MpePrefixCountersWithdrawsSent | read-only | current | Total number of prefixes which have been reported as withdrawn by the local BGP speaker to the peer in locally generated UPDATE messages to the peer. |
| 1.3.6.1.4.1.10876.101.2.77.35.1.9 | ColumnfsMIBgp4MpePrefixCountersInPrefixes | read-only | current | The number of prefixes received from a peer and are stored in the Adj-Ribs-In for that peer. |
| 1.3.6.1.4.1.10876.101.2.77.35.1.10 | ColumnfsMIBgp4MpePrefixCountersInPrefixesAccepted | read-only | current | The number of prefixes for a peer that are installed in the Adj-Ribs-In and are eligible to become active in the Loc-Rib. |
| 1.3.6.1.4.1.10876.101.2.77.35.1.11 | ColumnfsMIBgp4MpePrefixCountersInPrefixesRejected | read-only | current | The number of prefixes for a peer that are installed in the Adj-Ribs-In and are NOT eligible to become active in the Loc-Rib. |
| 1.3.6.1.4.1.10876.101.2.77.35.1.12 | ColumnfsMIBgp4MpePrefixCountersOutPrefixes | read-only | current | The number of prefixes for a peer that are installed in that peer's Adj-Ribs-Out. |
| 1.3.6.1.4.1.10876.101.2.77.36 | NodefsMIBgp4DistInOutRouteMap | |||
| 1.3.6.1.4.1.10876.101.2.77.36.1 | TablefsMIBgp4DistInOutRouteMapTable | not-accessible | current | A table describing the configuration of filtering for route map. |
| 1.3.6.1.4.1.10876.101.2.77.36.1.1 | RowfsMIBgp4DistInOutRouteMapEntry | not-accessible | current | Information describing the filtering configuration of single entry. |
| 1.3.6.1.4.1.10876.101.2.77.36.1.1.1 | ColumnfsMIBgp4DistInOutRouteMapName | not-accessible | current | Route map name. |
| 1.3.6.1.4.1.10876.101.2.77.36.1.1.2 | ColumnfsMIBgp4DistInOutRouteMapType | not-accessible | current | Type of route map to indicate the route map is for distribute in or for distribute out or for distance. 1 - distance 2 - distribute in 3 - distribute out |
| 1.3.6.1.4.1.10876.101.2.77.36.1.1.3 | ColumnfsMIBgp4DistInOutRouteMapValue | read-write | current | Distance value ( this will be unused for distribute list ) |
| 1.3.6.1.4.1.10876.101.2.77.36.1.1.4 | ColumnfsMIBgp4DistInOutRouteMapRowStatus | read-write | current | The status of this row, by which new entries may be created, or old entries deleted from this table. |
| 1.3.6.1.4.1.10876.101.2.77.37 | NodefsMIBgp4Notification | |||
| 1.3.6.1.4.1.10876.101.2.77.37.0 | NodefsMIBgp4Trap | |||
| 1.3.6.1.4.1.10876.101.2.77.37.0.1 | NotificationfsMIBgp4RestartStatusChange | current | A fsMIBgp4RestartStatusChange trap signifies that there has been a change in the graceful restart state for the router. This trap should be generated when the … | |
| 1.3.6.1.4.1.10876.101.2.77.37.0.3 | NotificationfsMIBgp4RouteAddRTMFailure | current | A fsMIBGP4RouteAddRTMFailure trap signifies failure in adding a route to RTM from BGP. | |
| 1.3.6.1.4.1.10876.101.2.77.37.1 | NodefsMIBgp4Objects | |||
| 1.3.6.1.4.1.10876.101.2.77.37.1.1 | ScalarfsMIBgp4TrapContextId | accessible-for-notify | current | This object refers to the BGP Context in which the route addition failed. |
| 1.3.6.1.4.1.10876.101.2.77.37.1.2 | ScalarfsMIBgp4TrapRouteAddressType | accessible-for-notify | current | This object refers to the addresstype of BGP Route. Used for sending BGP route addition failure Traps. |
| 1.3.6.1.4.1.10876.101.2.77.37.1.3 | ScalarfsMIBgp4TrapRoutePrefix | accessible-for-notify | current | This object refers to BGP Route. Used for sending BGP route addition failure Traps. |
| 1.3.6.1.4.1.10876.101.2.77.37.1.4 | ScalarfsMIBgp4NextHop | accessible-for-notify | current | This object refers to nexthop of bgp Route. Used for sending BGP route addition failure Traps. |
| 1.3.6.1.4.1.10876.101.2.77.37.1.5 | ScalarfsMIBgp4TrapPeerAddrType | accessible-for-notify | current | This object refers to the addresstype of bgp peer address. Used for sending BGP route addition failure Traps. |
| 1.3.6.1.4.1.10876.101.2.77.37.1.6 | ScalarfsMIBgp4TrapPeerAddr | accessible-for-notify | current | This object refers to the address of bgp peer from which route is learned. Used for sending BGP route addition failure Traps. |
| 1.3.6.1.4.1.10876.101.2.77.38 | NodefsMIBgp4NeighborRouteMap | |||
| 1.3.6.1.4.1.10876.101.2.77.38.1 | TablefsMIBgp4NeighborRouteMapTable | not-accessible | current | A table describing the configuration of route map on a neighbour. |
| 1.3.6.1.4.1.10876.101.2.77.38.1.1 | RowfsMIBgp4NeighborRouteMapEntry | not-accessible | current | Information describing the routemap configuration of single entry. |
| 1.3.6.1.4.1.10876.101.2.77.38.1.1.1 | ColumnfsMIBgp4NeighborRouteMapPeerAddrType | not-accessible | current | Adress type of the Neighbor. |
| 1.3.6.1.4.1.10876.101.2.77.38.1.1.2 | ColumnfsMIBgp4NeighborRouteMapPeer | not-accessible | current | IpAddress of the Neighbor. |
| 1.3.6.1.4.1.10876.101.2.77.38.1.1.3 | ColumnfsMIBgp4NeighborRouteMapDirection | not-accessible | current | Direction of route map to indicate the route map is for in or out. In direction routemap is to apply the routemap rules for incoming routes from the peer.Out d… |
| 1.3.6.1.4.1.10876.101.2.77.38.1.1.4 | ColumnfsMIBgp4NeighborRouteMapName | read-write | current | Route map name. |
| 1.3.6.1.4.1.10876.101.2.77.38.1.1.5 | ColumnfsMIBgp4NeighborRouteMapRowStatus | read-write | current | The status of this row, by which new entries may be created, or old entries deleted from this table. |
| 1.3.6.1.4.1.10876.101.2.77.39 | TablefsMIBgp4PeerGroupTable | not-accessible | current | A table for configuring the bgp peer groups. Configuring a property for the peer group copies it to all the peers present in the peer group. |
| 1.3.6.1.4.1.10876.101.2.77.39.1 | RowfsMIBgp4PeerGroupEntry | not-accessible | current | An entry describing the bgp peer group. |
| 1.3.6.1.4.1.10876.101.2.77.39.1.1 | ColumnfsMIBgp4PeerGroupName | not-accessible | current | The group name for this peer group entry. |
| 1.3.6.1.4.1.10876.101.2.77.39.1.2 | ColumnfsMIBgp4PeerGroupAddrType | read-only | current | The address type of the peers added to this peer group. |
| 1.3.6.1.4.1.10876.101.2.77.39.1.3 | ColumnfsMIBgp4PeerGroupRemoteAs | read-write | current | The remote autonomous system number for this peer group. |
| 1.3.6.1.4.1.10876.101.2.77.39.1.4 | ColumnfsMIBgp4PeerGroupHoldTimeConfigured | read-write | current | Time interval (in seconds) for the Hold Time configured for this BGP speaker with all the peers configured for this group. This value is placed in an OPEN mess… |
| 1.3.6.1.4.1.10876.101.2.77.39.1.5 | ColumnfsMIBgp4PeerGroupKeepAliveConfigured | read-write | current | Time interval (in seconds) for the KeepAlive timer configured for this BGP speaker with all the peers configured in this group. The value of this object will o… |
| 1.3.6.1.4.1.10876.101.2.77.39.1.6 | ColumnfsMIBgp4PeerGroupConnectRetryInterval | read-write | current | Time interval in seconds for the ConnectRetry timer for the peers in this group. The suggested value for this timer is 120 seconds. |
| 1.3.6.1.4.1.10876.101.2.77.39.1.7 | ColumnfsMIBgp4PeerGroupMinASOriginInterval | read-write | current | Time interval (in seconds) for the MinASOriginationInterval timer for all peers configured in this group. The suggested value for this timer is 15 seconds. |
| 1.3.6.1.4.1.10876.101.2.77.39.1.8 | ColumnfsMIBgp4PeerGroupMinRouteAdvInterval | read-write | current | Time interval (in seconds) for the MinRouteAdvertisementInterval timer. The suggested value for this timer is 30 seconds for EBGP connections and 5 seconds for… |
| 1.3.6.1.4.1.10876.101.2.77.39.1.9 | ColumnfsMIBgp4PeerGroupAllowAutomaticStart | read-write | current | This MIB object specifies whether BGP session with the peers in the peer group can be started automatically. This object when set to 'disabled', requires manua… |
| 1.3.6.1.4.1.10876.101.2.77.39.1.10 | ColumnfsMIBgp4PeerGroupAllowAutomaticStop | read-write | current | This MIB object specifies whether BGP session with the peers in the peer group need to be automatically stopped after a TCP connect-retry count value specified… |
| 1.3.6.1.4.1.10876.101.2.77.39.1.11 | ColumnfsMIBgp4PeerGroupIdleHoldTimeConfigured | read-write | current | IdleHoldTime specifies the length of time the BGP peers in this peer group is held in Idle state prior to allowing the next automatic restart. The IdleHoldTime… |
| 1.3.6.1.4.1.10876.101.2.77.39.1.12 | ColumnfsMIBgp4PeerGroupDampPeerOscillations | read-write | current | The DampPeerOscillations option specifies that the implementation engages additional logic to damp the oscillations of BGP peers in the face of series of autom… |
| 1.3.6.1.4.1.10876.101.2.77.39.1.13 | ColumnfsMIBgp4PeerGroupDelayOpen | read-write | current | This MIB object allows configuration option to enable/disable delay in sending of OPEN messages to the BGP peers for a specific time period (DelayOpenTime). Th… |
| 1.3.6.1.4.1.10876.101.2.77.39.1.14 | ColumnfsMIBgp4PeerGroupDelayOpenTimeConfigured | read-write | current | The DelayOpen time specifies the amount of time the BGP Peers should delay in sending the OPEN message to the remote peers. If the fsMIBgp4PeerGroupDelayOpen o… |
| 1.3.6.1.4.1.10876.101.2.77.39.1.15 | ColumnfsMIBgp4PeerGroupPrefixUpperLimit | read-write | current | BGP speaker imposes a locally-configured, upper bound on the number of address prefixes the speaker is willing to accept from a neighbor. The default value is … |
| 1.3.6.1.4.1.10876.101.2.77.39.1.16 | ColumnfsMIBgp4PeerGroupTcpConnectRetryCnt | read-write | current | This counter denotes the Maximum number of times the BGP Peers have tried to issue a TCP-Connect with its neighboring peers. The default value for the counter … |
| 1.3.6.1.4.1.10876.101.2.77.39.1.17 | ColumnfsMIBgp4PeerGroupEBGPMultiHop | read-write | current | This objects enables the BGP4 Speaker to accept or attempt connections to external peers residing on network that are not directly connected. By default, only … |
| 1.3.6.1.4.1.10876.101.2.77.39.1.18 | ColumnfsMIBgp4PeerGroupEBGPHopLimit | read-write | current | This objects enables the BGP4 Speaker to accept or attempt connections to external peers residing on network that are not directly connected and seperated by a… |
| 1.3.6.1.4.1.10876.101.2.77.39.1.19 | ColumnfsMIBgp4PeerGroupNextHopSelf | read-write | current | This object specifies how the next hop attribute sent in the update messages to the peers in this peer group. When the object takes the value of self,the next … |
| 1.3.6.1.4.1.10876.101.2.77.39.1.20 | ColumnfsMIBgp4PeerGroupRflClient | read-write | current | This object specifies whether the peers in this peer group are Client peers or Non-Client peers. By default, the peers are created as Non-Client Peer. |
| 1.3.6.1.4.1.10876.101.2.77.39.1.21 | ColumnfsMIBgp4PeerGroupTcpSendBufSize | read-write | current | This object configures the tcp window size on the sender side for all the peers in this peer group. |
| 1.3.6.1.4.1.10876.101.2.77.39.1.22 | ColumnfsMIBgp4PeerGroupTcpRcvBufSize | read-write | current | This object configures the tcp window size on the receiver side for all the peers in this peer group. |
| 1.3.6.1.4.1.10876.101.2.77.39.1.23 | ColumnfsMIBgp4PeerGroupCommSendStatus | read-create | current | Community Send status for the peers in this peer group. o none - is for read-only o send - send communities to this peer o donotsend - do not send communities … |
| 1.3.6.1.4.1.10876.101.2.77.39.1.24 | ColumnfsMIBgp4PeerGroupECommSendStatus | read-create | current | Extended Community Send status for the peers in this peer group. o none - is for read-only o send - send extended communities to this peer o donotsend - do not… |
| 1.3.6.1.4.1.10876.101.2.77.39.1.25 | ColumnfsMIBgp4PeerGroupPassive | read-write | current | This object is used to set the peers in this group to be active, that means the speaker will not initiate the session with the peers instead it waits for the r… |
| 1.3.6.1.4.1.10876.101.2.77.39.1.26 | ColumnfsMIBgp4PeerGroupDefaultOriginate | read-write | current | This object is used to enable/disable the advertisement of the default route to all the peers in this peer group. This object overrides the global default rout… |
| 1.3.6.1.4.1.10876.101.2.77.39.1.27 | ColumnfsMIBgp4PeerGroupActivateMPCapability | read-write | current | This object is set to activate the corresponding MP Capability. If any of MP Capability is activated, then this capability should be negotiated while establish… |
| 1.3.6.1.4.1.10876.101.2.77.39.1.28 | ColumnfsMIBgp4PeerGroupDeactivateMPCapability | read-write | current | This object is set to deactivate the corresponding MP Capability. If any of MP Capability is deactivated, then this capability should not be negotiated while e… |
| 1.3.6.1.4.1.10876.101.2.77.39.1.29 | ColumnfsMIBgp4PeerGroupRouteMapNameIn | read-write | current | This object is used to configure the in routemap for this peer group entry. |
| 1.3.6.1.4.1.10876.101.2.77.39.1.30 | ColumnfsMIBgp4PeerGroupRouteMapNameOut | read-write | current | This object is used to configure the out routemap for this peer group entry. |
| 1.3.6.1.4.1.10876.101.2.77.39.1.31 | ColumnfsMIBgp4PeerGroupStatus | read-write | current | This object is used to create the peer group or delete the group. |
| 1.3.6.1.4.1.10876.101.2.77.39.1.32 | ColumnfsMIBgp4PeerGroupIpPrefixNameIn | read-write | current | This object is used to configure the IP Prefix list name in IN direction for this peer group entry. |
| 1.3.6.1.4.1.10876.101.2.77.39.1.33 | ColumnfsMIBgp4PeerGroupIpPrefixNameOut | read-write | current | This object is used to configure the IP Prefix list name in OUT direction for this peer group entry. |
| 1.3.6.1.4.1.10876.101.2.77.39.1.34 | ColumnfsMIBgp4PeerGroupOrfType | read-write | current | This object is used to configure the ORF type supported for this peer group entry. This object should be configure before enabling the ORF modes fsMIBgp4PeerGr… |
| 1.3.6.1.4.1.10876.101.2.77.39.1.35 | ColumnfsMIBgp4PeerGroupOrfCapMode | read-write | current | This object is used to configure the ORF Capability mode supported for this peer group entry. If it is set to ZERO, then the both ORF modes will be disabled |
| 1.3.6.1.4.1.10876.101.2.77.39.1.36 | ColumnfsMIBgp4PeerGroupOrfRequest | read-write | current | This object is to trigger the ORF messages to the peers associated with this peer group entry. Once the ORF messages are transmitted, this object will be clear… |
| 1.3.6.1.4.1.10876.101.2.77.40 | TablefsMIBgp4PeerGroupListTable | not-accessible | current | A table for adding/removing the bgp peers to a peer group. |
| 1.3.6.1.4.1.10876.101.2.77.40.1 | RowfsMIBgp4PeerGroupListEntry | not-accessible | current | An entry describing the bgp peer group list. |
| 1.3.6.1.4.1.10876.101.2.77.40.1.1 | ColumnfsMIBgp4PeerAddrType | not-accessible | current | This object specifies the address type of the BGP peer entry added to this peer group entry |
| 1.3.6.1.4.1.10876.101.2.77.40.1.2 | ColumnfsMIBgp4PeerAddress | not-accessible | current | This object specifies the remote address of the BGP peer entry added to this peer group entry |
| 1.3.6.1.4.1.10876.101.2.77.40.1.3 | ColumnfsMIBgp4PeerAddStatus | read-write | current | This object is used to add or remove the bgp peer specified through fsMIBgp4PeerAddress to this bgp peer group entry. |
| 1.3.6.1.4.1.10876.101.2.77.41 | ScalarfsMIBgp4RestartReason | read-write | current | The reason for restart for the Restarting Router. Options include: unknown,softwarerestart,swreloadupgrade, switchtoredundant. This object is persistent and wh… |
| 1.3.6.1.4.1.10876.101.2.77.42 | NodefsMIBgp4TCPMKTAuth | |||
| 1.3.6.1.4.1.10876.101.2.77.42.1 | TablefsMIBgp4TCPMKTAuthTable | not-accessible | current | TCP MKT Authentication Table, used for configuring MKT for TCP-AO authentication, supported algorithms HMAC-SHA-1 and AES-128-CMAC |
| 1.3.6.1.4.1.10876.101.2.77.42.1.1 | RowfsMIBgp4TCPMKTAuthEntry | not-accessible | current | Entry corresponds to the TCP MKT parameters |
| 1.3.6.1.4.1.10876.101.2.77.42.1.1.1 | ColumnfsMIBgp4TCPMKTAuthKeyId | not-accessible | current | Send KeyID of the MKT. This object value is used to fill the key-id field in the TCP-AO option in the TCP header |
| 1.3.6.1.4.1.10876.101.2.77.42.1.1.2 | ColumnfsMIBgp4TCPMKTAuthRecvKeyId | read-write | current | Receive Key-id of the MKT. The MKT that is ready at the sender to be used to authenticate received segments is indicated to the peer by filling the receive key… |
| 1.3.6.1.4.1.10876.101.2.77.42.1.1.3 | ColumnfsMIBgp4TCPMKTAuthMasterKey | read-write | current | Master Key corresponding to the MKT |
| 1.3.6.1.4.1.10876.101.2.77.42.1.1.4 | ColumnfsMIBgp4TCPMKTAuthAlgo | read-write | current | Algorithm used for TCP-AO MAC or KDF calculation, allowed algorithms are HMAC-SHA-1 & AES-128-CMAC, default value is HMAC-SHA-1 |
| 1.3.6.1.4.1.10876.101.2.77.42.1.1.5 | ColumnfsMIBgp4TCPMKTAuthTcpOptExc | read-write | current | Exclude TCP options other than TCP-AO during MAC calculation, if fsMIBgp4TCPMKTAuthTcpOptExc is not set TCP-AO MAC will be calculated on tcp segment including … |
| 1.3.6.1.4.1.10876.101.2.77.42.1.1.6 | ColumnfsMIBgp4TCPMKTAuthRowStatus | read-write | current | This variable represents the status of the MKT entry, can have values allowed for RowStatus, eg. createAndGo, destroy etc |
| 1.3.6.1.4.1.10876.101.2.77.43 | NodefsMIBgp4TCPAOAuthPeer | |||
| 1.3.6.1.4.1.10876.101.2.77.43.1 | TablefsMIBgp4TCPAOAuthPeerTable | not-accessible | current | TCP-AO Peer config Table |
| 1.3.6.1.4.1.10876.101.2.77.43.1.1 | RowfsMIBgp4TCPAOAuthPeerEntry | not-accessible | current | Entry corresponds to the TCP-AO configs for peer, Support for associating one keyId(MKT) per peer is available at present. If a new keyId/MKT is associated wit… |
| 1.3.6.1.4.1.10876.101.2.77.43.1.1.1 | ColumnfsMIBgp4TCPAOAuthPeerType | not-accessible | current | The IP address type of the peer IP address |
| 1.3.6.1.4.1.10876.101.2.77.43.1.1.2 | ColumnfsMIBgp4TCPAOAuthPeerAddr | not-accessible | current | The IP address of this the peer for which TCP-AO config is done |
| 1.3.6.1.4.1.10876.101.2.77.43.1.1.3 | ColumnfsMIBgp4TCPAOAuthKeyId | not-accessible | current | Key id of the MKT which need to be associated with the peer |
| 1.3.6.1.4.1.10876.101.2.77.43.1.1.4 | ColumnfsMIBgp4TCPAOAuthKeyStatus | read-write | current | While doing a write on the object(snmpset) the value 'set(1)' will associate the MKT with KeyId mentioned in the index to the peer 'clear(2)' will clear/dissoc… |
| 1.3.6.1.4.1.10876.101.2.77.43.1.1.5 | ColumnfsMIBgp4TCPAOAuthKeyStartAccept | read-write | current | The date & time the router will start accepting packets that have been created with the MKT specified by the key-id. |
| 1.3.6.1.4.1.10876.101.2.77.43.1.1.6 | ColumnfsMIBgp4TCPAOAuthKeyStartGenerate | read-write | current | The date & time the router will start using the MKT specified by the key-id for packets generation. |
| 1.3.6.1.4.1.10876.101.2.77.43.1.1.7 | ColumnfsMIBgp4TCPAOAuthKeyStopGenerate | read-write | current | The date & time the router will stop using the MKT specified by the key-id for packets generation. |
| 1.3.6.1.4.1.10876.101.2.77.43.1.1.8 | ColumnfsMIBgp4TCPAOAuthKeyStopAccept | read-write | current | The date & time the router will stop accepting packets that have been created withthe MKT specified by the key-id. |
| 1.3.6.1.4.1.10876.101.2.77.44 | TablefsMIBgp4ORFListTable | not-accessible | current | A table for adding/removing Outbound Route Filter entries received from the peer |
| 1.3.6.1.4.1.10876.101.2.77.44.1 | RowfsMIBgp4ORFListEntry | not-accessible | current | An entry describing the bgp ORF list. |
| 1.3.6.1.4.1.10876.101.2.77.44.1.1 | ColumnfsMIBgp4ORFPeerAddrType | not-accessible | current | This object specifies the address type of the BGP peer associated with this ORF entry |
| 1.3.6.1.4.1.10876.101.2.77.44.1.2 | ColumnfsMIBgp4ORFPeerAddr | not-accessible | current | This object specifies the remote address of the BGP peer associated with this ORF entry |
| 1.3.6.1.4.1.10876.101.2.77.44.1.3 | ColumnfsMIBgp4ORFAfi | not-accessible | current | This object specifies the type of IP address prefix in the ORF entry. |
| 1.3.6.1.4.1.10876.101.2.77.44.1.4 | ColumnfsMIBgp4ORFSafi | not-accessible | current | This object specifies the Sub-sequent address family of IP address prefix in the ORF entry. |
| 1.3.6.1.4.1.10876.101.2.77.44.1.5 | ColumnfsMIBgp4ORFType | not-accessible | current | This object specifies the type of the ORF entry. Currently it supports only Address-Prefix based ORF type (64) |
| 1.3.6.1.4.1.10876.101.2.77.44.1.6 | ColumnfsMIBgp4ORFSequence | not-accessible | current | This object specifies the sequential order in which a route should be matched against an ORF entry. |
| 1.3.6.1.4.1.10876.101.2.77.44.1.7 | ColumnfsMIBgp4ORFAddrPrefix | not-accessible | current | This object specifies the IP address prefix for which the ORF rule was specified. |
| 1.3.6.1.4.1.10876.101.2.77.44.1.8 | ColumnfsMIBgp4ORFAddrPrefixLen | not-accessible | current | This object specifies the length of the IP address prefix length in bits which will be considered when matching a route with the ORF entry. |
| 1.3.6.1.4.1.10876.101.2.77.44.1.9 | ColumnfsMIBgp4ORFMinLength | not-accessible | current | This object specifies the minimum prefix-length in bits for a IP address prefix. Any route with prefix-length equal to or greater than this length will be cons… |
| 1.3.6.1.4.1.10876.101.2.77.44.1.10 | ColumnfsMIBgp4ORFMaxLength | not-accessible | current | This object specifies the maximum prefix-length in bits for a IP address prefix. Any route with prefix-length equal to or less than this length will be conside… |
| 1.3.6.1.4.1.10876.101.2.77.44.1.11 | ColumnfsMIBgp4ORFAction | not-accessible | current | This object specifies the action to be taken for a particular route if it matches with the ORF rules defined in this particular ORF entry. If it is PERMIT, the… |