SYNSO-UPSMIB
105 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC1155-SMI | enterprises IpAddress |
| RFC1213-MIB | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9557 | Nodesynso | |||
| 1.3.6.1.4.1.9557.1 | NodesynsoUpsSoftware | |||
| 1.3.6.1.4.1.9557.1.1 | NodesyupsBasicSetting | |||
| 1.3.6.1.4.1.9557.1.1.1 | ScalarsyupsPlatForm | read-only | mandatory | The platform which the UPS software is running on. |
| 1.3.6.1.4.1.9557.1.1.2 | TablesyupsFeatureTable | not-accessible | mandatory | A table containing the supported features. |
| 1.3.6.1.4.1.9557.1.1.2.1 | RowsyupsFeatureEntry | not-accessible | mandatory | An entry representing the support information for a feature. |
| 1.3.6.1.4.1.9557.1.1.2.1.1 | ColumnsyupsFeature | read-only | mandatory | The string representing a feature. |
| 1.3.6.1.4.1.9557.1.1.2.1.2 | ColumnsyupsSupportInfo | read-only | mandatory | The string containing the support information for a feature. |
| 1.3.6.1.4.1.9557.1.1.3 | ScalarsyupsSystemStartTime | read-only | mandatory | The time that the UPS software starts. It is the number of seconds elapsed since 00:00:00, January 1, 1970. |
| 1.3.6.1.4.1.9557.1.1.4 | ScalarsyupsSignalType | read-write | mandatory | The signaling method between the UPS and software. When the basicSignal used, the UPS changes the voltage level of some specific pins to notify the software of… |
| 1.3.6.1.4.1.9557.1.1.5 | ScalarsyupsBasicSignalDefinition | read-only | mandatory | The signal definitions for the basic signaling UPS. The value can be the following bit combinations: SG_POWER_FAILURE_ENABLE 0x01 SG_BATTERY_LOW_ENABLE 0x02 SG… |
| 1.3.6.1.4.1.9557.1.1.6 | ScalarsyupsUpsComPort | read-write | mandatory | The serial port which the UPS software use to communicate with the UPS. The format varies from platform to platform. For DOS program, the format is 'portNo, po… |
| 1.3.6.1.4.1.9557.1.1.7 | ScalarsyupsModemComPort | read-write | mandatory | The serial port which the UPS software use to dial out when some particular events occur. The format varies from platform to platform. For DOS program, the for… |
| 1.3.6.1.4.1.9557.1.2 | NodesyupsUpsExtension | |||
| 1.3.6.1.4.1.9557.1.2.1 | ScalarsyupsUpsAlarm | read-only | mandatory | It is used internally. Each bit indicates a critical event, such as input bad, on battery, communications lost, ...,etc. |
| 1.3.6.1.4.1.9557.1.2.2 | ScalarsyupsSerialNo | read-only | mandatory | The serial number of the UPS connected to the UPS software. |
| 1.3.6.1.4.1.9557.1.2.3 | ScalarsyupsConfigBatteryVoltage | read-only | mandatory | The nominal battery voltage. |
| 1.3.6.1.4.1.9557.1.2.4 | ScalarsyupsBatteryReplaceDate | read-write | mandatory | The last battery replacement date. It represents the number of days elapsed since January 1, 1901. |
| 1.3.6.1.4.1.9557.1.2.5 | ScalarsyupsNoOutlet | read-only | mandatory | The total number of controllable outlets. |
| 1.3.6.1.4.1.9557.1.2.6 | ScalarsyupsOutletParamter | read-write | mandatory | This object is not used any more. |
| 1.3.6.1.4.1.9557.1.2.7 | ScalarsyupsShutdownDepend | read-write | mandatory | A string containing those who should perform their shutdown procedure before the UPS turns off. The agent will inform each one in the list to begin their shutd… |
| 1.3.6.1.4.1.9557.1.2.8 | ScalarsyupsEnableAutoSave | read-write | mandatory | Setting it to 1, the agent will try to save all files opened by applications before shutting down the operation system. Setting it to 0 will disable the auto s… |
| 1.3.6.1.4.1.9557.1.2.9 | ScalarsyupsShutdownOsDelay | read-write | mandatory | The delay time before shutting down the operation system. When it is necessary to shut down the operation system, the agent will run the specified command file… |
| 1.3.6.1.4.1.9557.1.2.10 | ScalarsyupsShutdownUpsDelay | read-write | mandatory | The delay time before shutting down the UPS. Before shutting down the operation system, the agent will send a command to tell the UPS to shut down. This delay … |
| 1.3.6.1.4.1.9557.1.2.11 | ScalarsyupsSaveConfig | read-write | mandatory | Used to inform the agnet to save the configurations. Its value indicates which group to be saved. For example, a 1 indicates group 1 (syupsBasicSetting) to be … |
| 1.3.6.1.4.1.9557.1.2.12 | ScalarsyupsNoOutlets | read-only | mandatory | The number of controllable outlets. |
| 1.3.6.1.4.1.9557.1.2.13 | TablesyupsOutletTable | not-accessible | mandatory | A list of outlet table entries. The number of entries is given by the value of syupsNoOutlets. |
| 1.3.6.1.4.1.9557.1.2.13.1 | RowsyupsOutletEntry | not-accessible | mandatory | An entry containing information applicable to a particular controllable outlet. |
| 1.3.6.1.4.1.9557.1.2.13.1.1 | ColumnsyupsOutletIndex | not-accessible | mandatory | The outlet identifier. |
| 1.3.6.1.4.1.9557.1.2.13.1.2 | ColumnsyupsOutletDescription | read-write | mandatory | The outlet description. |
| 1.3.6.1.4.1.9557.1.2.13.1.3 | ColumnsyupsOutletShutdownDelay | read-write | mandatory | The delay time (in seconds) before turning off the outlet. Before turning off the outlet, the agent will send a shutdown command to anyone specified in the syu… |
| 1.3.6.1.4.1.9557.1.2.13.1.4 | ColumnsyupsOutletShutdownDepend | read-write | mandatory | A string containing those who should perform their shutdown procedure before the outlet turns off. The agent will inform each one in the list to begin their sh… |
| 1.3.6.1.4.1.9557.1.2.14 | ScalarsyupsOutletOperator | read-write | mandatory | The operator is used to control the outlets. There are two commands: 1. 'SWITCH: OutletNo, OnOff'. The OutletNo specify the outlet. The OnOff can be 0 (off) or… |
| 1.3.6.1.4.1.9557.1.3 | NodesyupsEventAction | |||
| 1.3.6.1.4.1.9557.1.3.1 | ScalarsyupsNoEventActionEntries | read-only | mandatory | The number of event-action items. This variable indicates the number of rows in the event-action table. |
| 1.3.6.1.4.1.9557.1.3.2 | TablesyupsEventActionTable | not-accessible | mandatory | A list of event action entries. The number of entries is given by the value of syupsNoEventActionEntries. |
| 1.3.6.1.4.1.9557.1.3.2.1 | RowsyupsEventActionEntry | not-accessible | mandatory | An entry containing information applicable to a particular event action. |
| 1.3.6.1.4.1.9557.1.3.2.1.1 | ColumnsyupsEventId | read-only | mandatory | The event ID. |
| 1.3.6.1.4.1.9557.1.3.2.1.2 | ColumnsyupsLogEnable | read-write | mandatory | Whether to log the event in the log file when it occurs. A 1 indicates enable, a 0 indicates disable. |
| 1.3.6.1.4.1.9557.1.3.2.1.3 | ColumnsyupsNotifyEnable | read-write | mandatory | Whether to notify users when the event occurs. A 1 indicates enable, a 0 indicates disable. |
| 1.3.6.1.4.1.9557.1.3.2.1.4 | ColumnsyupsNotifyDelay | read-write | mandatory | How long the event must last before notifying users. |
| 1.3.6.1.4.1.9557.1.3.2.1.5 | ColumnsyupsNotifyMessage | read-write | mandatory | The message which will be sent when the event occurs. |
| 1.3.6.1.4.1.9557.1.3.2.1.6 | ColumnsyupsNotifyPeriod | read-write | mandatory | How often (in seconds) to send the message. The -1 means once. |
| 1.3.6.1.4.1.9557.1.3.2.1.7 | ColumnsyupsNotifyUsers | read-write | mandatory | Who will receive the message when the event occurs. |
| 1.3.6.1.4.1.9557.1.3.2.1.8 | ColumnsyupsEmailEnable | read-write | mandatory | Whether to email users when the event occurs. A 1 indicates enable, a 0 indicates disable. |
| 1.3.6.1.4.1.9557.1.3.2.1.9 | ColumnsyupsEmailDelay | read-write | mandatory | How long the event must last before emailing users. |
| 1.3.6.1.4.1.9557.1.3.2.1.10 | ColumnsyupsEmailMessage | read-write | mandatory | The additional message which will be sent when the event occurs. |
| 1.3.6.1.4.1.9557.1.3.2.1.11 | ColumnsyupsEmailUsers | read-write | mandatory | Who will receive the mail when the event occurs. |
| 1.3.6.1.4.1.9557.1.3.2.1.12 | ColumnsyupsPageEnable | read-write | mandatory | Whether to page users when the event occurs. A 1 indicates enable, a 0 indicates disable. |
| 1.3.6.1.4.1.9557.1.3.2.1.13 | ColumnsyupsPageDelay | read-write | mandatory | How long the event must last before paging users. |
| 1.3.6.1.4.1.9557.1.3.2.1.14 | ColumnsyupsPageMessage | read-write | mandatory | The message which will be sent when the event occurs. |
| 1.3.6.1.4.1.9557.1.3.2.1.15 | ColumnsyupsPageUsers | read-write | mandatory | Who will receive the code when the event occurs. |
| 1.3.6.1.4.1.9557.1.3.2.1.16 | ColumnsyupsCommandEnable | read-write | mandatory | Whether to execute the external command file when the event occurs. A 1 indicates enable, a 0 indicates disable. |
| 1.3.6.1.4.1.9557.1.3.2.1.17 | ColumnsyupsCommandDelay | read-write | mandatory | How long the event must last before executing the external command file. |
| 1.3.6.1.4.1.9557.1.3.2.1.18 | ColumnsyupsCommandFile | read-write | mandatory | The external command file which will be executed when the event occurs. |
| 1.3.6.1.4.1.9557.1.3.2.1.19 | ColumnsyupsShutdownEnable | read-write | mandatory | Whether to shut down the system when the event occurs. A 1 indicates enable, a 0 indicates disable. |
| 1.3.6.1.4.1.9557.1.3.2.1.20 | ColumnsyupsShutdownDelay | read-write | mandatory | How long the event must last before shutting down the system. |
| 1.3.6.1.4.1.9557.1.4 | NodesyupsHistory | |||
| 1.3.6.1.4.1.9557.1.4.1 | ScalarsyupsMaxEventFileLength | read-write | mandatory | The maximum length (in bytes) of the event log file. UPS software will cut the first half of the file whenever the file exceeds this maximum length. |
| 1.3.6.1.4.1.9557.1.4.2 | ScalarsyupsEventNumRecords | read-only | mandatory | The total number of records in the event log file. |
| 1.3.6.1.4.1.9557.1.4.3 | TablesyupsEventTable | not-accessible | mandatory | A list of event entries. Each entry represents a record in the event log file. |
| 1.3.6.1.4.1.9557.1.4.3.1 | RowsyupsEventEntry | not-accessible | mandatory | An entry representing a record in the event log file. |
| 1.3.6.1.4.1.9557.1.4.3.1.1 | ColumnsyupsEventIndex | read-only | mandatory | The record number of an event entry. |
| 1.3.6.1.4.1.9557.1.4.3.1.2 | ColumnsyupsEventRecord | read-only | mandatory | The string containing an event entry. |
| 1.3.6.1.4.1.9557.1.4.4 | ScalarsyupsDataRecordInterval | read-write | mandatory | The number of minutes to wait between each recording to the data log file. |
| 1.3.6.1.4.1.9557.1.4.5 | ScalarsyupsMaxDataFileLength | read-write | mandatory | The maximum length (in bytes) of the data log file. UPS software will cut the first half of the file whenever the file exceeds this maximum length. |
| 1.3.6.1.4.1.9557.1.4.6 | ScalarsyupsDataNumRecords | read-only | mandatory | The total number of records in the data log file. |
| 1.3.6.1.4.1.9557.1.4.7 | TablesyupsDataTable | not-accessible | mandatory | A list of data entries. Each entry represents a record in the data log file. |
| 1.3.6.1.4.1.9557.1.4.7.1 | RowsyupsDataEntry | not-accessible | mandatory | An entry representing a record in the data log file. |
| 1.3.6.1.4.1.9557.1.4.7.1.1 | ColumnsyupsDataIndex | read-only | mandatory | The record number of a data entry. |
| 1.3.6.1.4.1.9557.1.4.7.1.2 | ColumnsyupsDataRecord | read-only | mandatory | The string containing a data entry. |
| 1.3.6.1.4.1.9557.1.4.8 | ScalarsyupsHistoryOperator | read-write | mandatory | The operator which is used to operate on the history file. The command format is 'Command, File, Range'. So far, Command can be PURGE, File can be EVENT or DAT… |
| 1.3.6.1.4.1.9557.1.4.9 | ScalarsyupsScopeSettings | read-write | mandatory | The string contains the settings for UPS Scope Chart, including Value Original Point, Value Unit, Time Unit, Time Interval, and Display Items. The format for t… |
| 1.3.6.1.4.1.9557.1.5 | NodesyupsSchedule | |||
| 1.3.6.1.4.1.9557.1.5.1 | ScalarsyupsNoSchEntries | read-only | mandatory | The total number of schedule entries. |
| 1.3.6.1.4.1.9557.1.5.2 | ScalarsyupsSchOperator | read-write | mandatory | The operator which is used to operate on the schedule table. There are three commands: 1. 'ADD: action, mm/dd/yyyy, hh:mm:ss, week_day, repeat' indicates to ad… |
| 1.3.6.1.4.1.9557.1.5.3 | TablesyupsSchTable | not-accessible | mandatory | A list of schedule entries. |
| 1.3.6.1.4.1.9557.1.5.3.1 | RowsyupsSchEntry | not-accessible | mandatory | A schedule entry. |
| 1.3.6.1.4.1.9557.1.5.3.1.1 | ColumnsyupsSchIndex | read-only | mandatory | The entry number of a schedule setting. |
| 1.3.6.1.4.1.9557.1.5.3.1.2 | ColumnsyupsSchStartDate | read-only | mandatory | The starting date (mm/dd/yyyy) of the schedule entry. |
| 1.3.6.1.4.1.9557.1.5.3.1.3 | ColumnsyupsSchStartTime | read-only | mandatory | The starting time (hh:mm:ss) of the schedule entry. |
| 1.3.6.1.4.1.9557.1.5.3.1.4 | ColumnsyupsSchWeekDay | read-only | mandatory | The starting day of week for the schedule entry. It could be Sun(0), Mon(1), ..., and Sat(6). It is used when syupsSchRepeat is set to weekly. |
| 1.3.6.1.4.1.9557.1.5.3.1.5 | ColumnsyupsSchAction | read-only | mandatory | The action of the schedule entry. It could be: General System Test (1) Quick Battery Test (2) Deep Battery Test (3) Turn On UPS (11) Turn Off UPS (21) Turn On … |
| 1.3.6.1.4.1.9557.1.5.3.1.6 | ColumnsyupsSchRepeat | read-only | mandatory | It indicates the frequency of the action, it could be Once(1), Daily(2), Weekly(3) and Monthly(4). |
| 1.3.6.1.4.1.9557.1.6 | NodesyupsCoworker | |||
| 1.3.6.1.4.1.9557.1.6.1 | ScalarsyupsNoAccessControl | read-only | mandatory | The total number of access control entries. |
| 1.3.6.1.4.1.9557.1.6.2 | ScalarsyupsAccessControlOperator | read-write | mandatory | The operator which is used to operate on the access control table. There are three commands: 1. 'ADD: community' indicates to add a new entry to the access con… |
| 1.3.6.1.4.1.9557.1.6.3 | TablesyupsAccessControlTable | not-accessible | mandatory | A list of access control entries. Only entries in this list can have access to the agent. |
| 1.3.6.1.4.1.9557.1.6.3.1 | RowsyupsAccessControlEntry | not-accessible | mandatory | An access control entry. |
| 1.3.6.1.4.1.9557.1.6.3.1.1 | ColumnsyupsAccessControlIndex | read-only | mandatory | The entry number of a access control setting. |
| 1.3.6.1.4.1.9557.1.6.3.1.2 | ColumnsyupsAccessControlSetting | read-only | mandatory | A string containing the community name. |
| 1.3.6.1.4.1.9557.1.6.4 | ScalarsyupsNoTrapReceiver | read-only | mandatory | The total number of trap receiver entries. |
| 1.3.6.1.4.1.9557.1.6.5 | ScalarsyupsTrapReceiverOperator | read-write | mandatory | The operator which is used to operate on the trap receiver table. There are three commands: 1. 'ADD: ipAddress' indicates to add a new entry to the trap receiv… |
| 1.3.6.1.4.1.9557.1.6.6 | TablesyupsTrapReceiverTable | not-accessible | mandatory | A list of trap receiver entries. When an important event occurs, the agent will send traps to all the entries in the list. |
| 1.3.6.1.4.1.9557.1.6.6.1 | RowsyupsTrapReceiverEntry | not-accessible | mandatory | An trap receiver entry. |
| 1.3.6.1.4.1.9557.1.6.6.1.1 | ColumnsyupsTrapReceiverIndex | read-only | mandatory | The entry number of a trap receiver setting. |
| 1.3.6.1.4.1.9557.1.6.6.1.2 | ColumnsyupsTrapReceiverSetting | read-only | mandatory | A string containing a trap receiver's IP address. |
| 1.3.6.1.4.1.9557.1.7 | NodesyupsTraps | |||
| 1.3.6.1.4.1.9557.1.7.1 | NotificationsyupsTrapOverTemperature | current | The battery temperature is too high. This trap is persistent and is resent at one minute intervals until the UPS either turns off or the status is no longer pr… | |
| 1.3.6.1.4.1.9557.1.7.2 | NotificationsyupsTrapOverCurrent | current | The current is too high. This trap is persistent and is resent at one minute intervals until the UPS either turns off or the status is no longer present. | |
| 1.3.6.1.4.1.9557.1.7.3 | NotificationsyupsTrapOverVoltage | current | The voltage is too high. This trap is persistent and is resent at one minute intervals until the UPS either turns off or the status is no longer present. | |
| 1.3.6.1.4.1.9557.1.7.4 | NotificationsyupsTrapUnderVoltage | current | The voltage is too low. This trap is persistent and is resent at one minute intervals until the UPS either turns off or the status is no longer present. | |
| 1.3.6.1.4.1.9557.1.7.5 | NotificationsyupsOffFrequency | current | The frequency is abnormal. This trap is persistent and is resent at one minute intervals until the UPS either turns off or the status is no longer present. | |
| 1.3.6.1.4.1.9557.1.7.6 | NotificationsyupsLowBattery | current | The battery is too low. This trap is persistent and is resent at one minute intervals until the UPS either turns off or the status is no longer present. | |
| 1.3.6.1.4.1.9557.1.7.7 | NotificationsyupsBadBattery | current | The battery is bad. This trap is persistent and is resent at one minute intervals until the UPS either turns off or the status is no longer present. |