SYSTEM-RESOURCE-MIB
24 objects
No module-level DESCRIPTION found.
Imported Objects
| CTRON-MIB-NAMES | ctResource |
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | TimeTicks |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.52.4.1.1.12.1 | NodesysResourceInstalled | |||
| 1.3.6.1.4.1.52.4.1.1.12.1.1 | TablesysResourceCpuTable | not-accessible | mandatory | This table defines the CPus present within the system. |
| 1.3.6.1.4.1.52.4.1.1.12.1.1.1 | RowsysResourceCpuEntry | not-accessible | mandatory | Defines a particular CPU entry. |
| 1.3.6.1.4.1.52.4.1.1.12.1.1.1.1 | ColumnsysResSlotID | read-only | mandatory | The slot for which this CPU information pertains. |
| 1.3.6.1.4.1.52.4.1.1.12.1.1.1.2 | ColumnsysResCpuIndex | read-only | mandatory | An identifier for the CPU on a per slot basis. |
| 1.3.6.1.4.1.52.4.1.1.12.1.1.1.3 | ColumnsysResCpuType | read-only | mandatory | The processor (CPU) type. |
| 1.3.6.1.4.1.52.4.1.1.12.1.1.1.4 | ColumnsysResCpuSpeed | read-only | mandatory | The speed of the processor in mega-hertz. |
| 1.3.6.1.4.1.52.4.1.1.12.1.1.1.5 | ColumnsysResCpuID | read-only | mandatory | A system wide unique identifier for each CPU. |
| 1.3.6.1.4.1.52.4.1.1.12.1.1.1.6 | ColumnsysResInstalledLocalMemory | read-only | mandatory | Total installed local memory 'DRAM' used for code and data. This is reported in mega-bytes. |
| 1.3.6.1.4.1.52.4.1.1.12.1.1.1.7 | ColumnsysResUsedLocalMemory | read-only | mandatory | The current amount of local memory 'DRAM' that is currently being used for code and data. This is reported in bytes. |
| 1.3.6.1.4.1.52.4.1.1.12.1.2 | TablesysResourceTable | not-accessible | mandatory | This table describes total installed system resources. |
| 1.3.6.1.4.1.52.4.1.1.12.1.2.1 | RowsysResourceEntry | not-accessible | mandatory | Describes a particular installed set of system resources. |
| 1.3.6.1.4.1.52.4.1.1.12.1.2.1.1 | ColumnsysResInstalledNvram | read-only | mandatory | The total installed non-volatile memory 'NVRAM'. This is reported in K-bytes. |
| 1.3.6.1.4.1.52.4.1.1.12.1.2.1.2 | ColumnsysResInstalledFlash | read-only | mandatory | The total installed flash memory. This is reported in K-bytes. |
| 1.3.6.1.4.1.52.4.1.1.12.1.2.1.3 | ColumnsysResInstalledSharedMemory | read-only | mandatory | The total amount of shared memory that is installed. This is reported in K-bytes. |
| 1.3.6.1.4.1.52.4.1.1.12.1.2.1.4 | ColumnsysResUsedNvram | read-only | mandatory | The current amount of non-volatile memory 'NVRAM' that is currently being used for data. This is reported in bytes. |
| 1.3.6.1.4.1.52.4.1.1.12.1.2.1.5 | ColumnsysResUsedFlash | read-only | mandatory | The current amount of flash memory that is currently being used for code and data. This is reported in bytes. |
| 1.3.6.1.4.1.52.4.1.1.12.1.2.1.6 | ColumnsysResUsedSharedMemory | read-only | mandatory | The current amount of shared memory that is currently being used for data. This is reported in bytes. |
| 1.3.6.1.4.1.52.4.1.1.12.2 | NodesysResourceSwitch | |||
| 1.3.6.1.4.1.52.4.1.1.12.2.1 | ScalarsysResManagementCpuResource | read-write | mandatory | The desired amount of CPU bandwith reserved for management purposes. For example, in the default state (1), the device will devote all CPU bandwith to switchin… |
| 1.3.6.1.4.1.52.4.1.1.12.2.2 | ScalarswitchLoad | read-only | mandatory | The returned value represents the current switch load based upon a percentage of maximum switching capacity where maximum switching capacity is 100%. |
| 1.3.6.1.4.1.52.4.1.1.12.2.3 | ScalarpeakSwitchload | read-only | mandatory | The peak load which has occured on this switch. The value returned represents The peak percentage of switch load based upon a percentage of maximum switch load… |
| 1.3.6.1.4.1.52.4.1.1.12.2.4 | ScalarpeakSwitchLoadTime | read-only | mandatory | The time at which the peak switch load occured. The value returned will represent system up time at which the peak occured. |
| 1.3.6.1.4.1.52.4.1.1.12.2.5 | ScalarpeakSwitchClear | read-write | mandatory | This object is used to clear the values found in peakSwitchload and peakSwitchLoadTime. When set with a value of clear(1) the values will be cleared. When read… |