TE-MIB
85 objects
The Traffic Engineering MIB module. Copyright (C) The Internet Society (2005). This version of this MIB module is part of RFC 3970; see the RFC itself for full legal notices.
Imported Objects
| MPLS-TC-STD-MIB | MplsBitRate TeHopAddress TeHopAddressType |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 Gauge32 Integer32 mib-2 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | RowStatus StorageType TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.122 | IdentityteMIB | The Traffic Engineering MIB module. Copyright (C) The Internet Society (2005). This version of this MIB module is part of RFC 3970; see the RFC itself for full… | ||
| 1.3.6.1.2.1.122.0 | NodeteMIBNotifications | |||
| 1.3.6.1.2.1.122.0.1 | NotificationteTunnelUp | current | A teTunnelUp notification is generated when the Tunnel indexed by teTunnelName transitions to the 'up' state. A tunnel is up when at least one of its paths is … | |
| 1.3.6.1.2.1.122.0.2 | NotificationteTunnelDown | current | A teTunnelDown notification is generated when the Tunnel indexed by teTunnelName transitions to the 'down' state. A tunnel is up when at least one of its paths… | |
| 1.3.6.1.2.1.122.0.3 | NotificationteTunnelChanged | current | A teTunnelChanged notification is generated when an active path on the Tunnel indexed by teTunnelName changes or a new path becomes active. The value of tePath… | |
| 1.3.6.1.2.1.122.0.4 | NotificationteTunnelRerouted | current | A teTunnelRerouted notification is generated when an active path for the Tunnel indexed by teTunnelName stays the same, but its route changes. This notificatio… | |
| 1.3.6.1.2.1.122.1 | NodeteMIBObjects | |||
| 1.3.6.1.2.1.122.1.1 | NodeteInfo | |||
| 1.3.6.1.2.1.122.1.1.1 | ScalarteDistProtocol | read-only | current | IGP used to distribute Traffic Engineering information and topology to each device for the purpose of automatic path computation. More than one IGP may be used… |
| 1.3.6.1.2.1.122.1.1.2 | ScalarteSignalingProto | read-only | current | Traffic Engineering signaling protocols supported by this device. More than one protocol may be supported. |
| 1.3.6.1.2.1.122.1.1.3 | ScalarteNotificationEnable | read-write | current | If this object is true, then it enables the generation of notifications from this MIB module. Otherwise notifications are not generated. |
| 1.3.6.1.2.1.122.1.1.4 | ScalarteNextTunnelIndex | read-only | current | An integer that may be used as a new Index in the teTunnelTable. The special value of 0 indicates that no more new entries can be created in that table. When t… |
| 1.3.6.1.2.1.122.1.1.5 | ScalarteNextPathHopIndex | read-only | current | An integer that may be used as a new Index in the tePathHopTable. The special value of 0 indicates that no more new entries can be created in that table. When … |
| 1.3.6.1.2.1.122.1.1.6 | ScalarteConfiguredTunnels | read-only | current | Number of currently configured Tunnels. |
| 1.3.6.1.2.1.122.1.1.7 | ScalarteActiveTunnels | read-only | current | Number of currently active Tunnels. |
| 1.3.6.1.2.1.122.1.1.8 | ScalartePrimaryTunnels | read-only | current | Number of currently active Tunnels running on their primary paths. |
| 1.3.6.1.2.1.122.1.1.9 | TableteAdminGroupTable | not-accessible | current | A mapping of configured administrative groups. Each entry represents an Administrative Group and provides a name and index for the group. Administrative groups… |
| 1.3.6.1.2.1.122.1.1.9.1 | RowteAdminGroupEntry | not-accessible | current | A mapping between a configured group number and its human-readable name. The group number should be between 1 and 32, inclusive. Group number n represents bit … |
| 1.3.6.1.2.1.122.1.1.9.1.1 | ColumnteAdminGroupNumber | not-accessible | current | Index of the administrative group. |
| 1.3.6.1.2.1.122.1.1.9.1.2 | ColumnteAdminGroupName | read-create | current | Name of the administrative group. |
| 1.3.6.1.2.1.122.1.1.9.1.3 | ColumnteAdminGroupRowStatus | read-create | current | The status of this conceptual row. The value of this object has no effect on whether other objects in this conceptual row can be modified. |
| 1.3.6.1.2.1.122.1.2 | TableteTunnelTable | not-accessible | current | Table of Configured Traffic Tunnels. |
| 1.3.6.1.2.1.122.1.2.1 | RowteTunnelEntry | not-accessible | current | Entry containing information about a particular Traffic Tunnel. |
| 1.3.6.1.2.1.122.1.2.1.1 | ColumnteTunnelIndex | not-accessible | current | A unique index that identifies a Tunnel. If the TE Tunnel is considered an interface, then this index must match the interface index of the corresponding inter… |
| 1.3.6.1.2.1.122.1.2.1.2 | ColumnteTunnelName | read-create | current | Name of the Traffic Tunnel. Note that the name of a Tunnel MUST be unique. When a SET request contains a name that is already in use for another entry, then th… |
| 1.3.6.1.2.1.122.1.2.1.3 | ColumnteTunnelNextPathIndex | read-only | current | An integer that may be used as a new Index for the next Path in this Tunnel. The special value of 0 indicates that no more Paths can be created for this Tunnel… |
| 1.3.6.1.2.1.122.1.2.1.4 | ColumnteTunnelRowStatus | read-create | current | The status of this conceptual row. When the value of this object is 'active', then the values for the corresponding objects teTunnelName, teTunnelSourceAddress… |
| 1.3.6.1.2.1.122.1.2.1.5 | ColumnteTunnelStorageType | read-create | current | The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. |
| 1.3.6.1.2.1.122.1.2.1.6 | ColumnteTunnelSourceAddressType | read-create | current | The type of Traffic Engineered Tunnel hop address for the source of this Tunnel. Typically, this address type is IPv4 or IPv6, with a prefix length of 32 or 12… |
| 1.3.6.1.2.1.122.1.2.1.7 | ColumnteTunnelSourceAddress | read-create | current | The Source Traffic Engineered Tunnel hop address of this Tunnel. The type of this address is determined by the value of the corresponding teTunnelSourceAddress… |
| 1.3.6.1.2.1.122.1.2.1.8 | ColumnteTunnelDestinationAddressType | read-create | current | The type of Traffic Engineered Tunnel hop address for the destination of this Tunnel. The value of this object cannot be changed if the value of the correspond… |
| 1.3.6.1.2.1.122.1.2.1.9 | ColumnteTunnelDestinationAddress | read-create | current | The Destination Traffic Engineered Tunnel hop address of this Tunnel. The type of this address is determined by the value of the corresponding teTunnelDestinat… |
| 1.3.6.1.2.1.122.1.2.1.10 | ColumnteTunnelState | read-only | current | The operational state of the Tunnel. |
| 1.3.6.1.2.1.122.1.2.1.11 | ColumnteTunnelDiscontinuityTimer | read-only | current | The value of sysUpTime on the most recent occasion at which any one or more of this tunnel's counters suffered a discontinuity. The relevant counters are teTun… |
| 1.3.6.1.2.1.122.1.2.1.12 | ColumnteTunnelOctets | read-only | current | The number of octets that have been forwarded over the Tunnel. Discontinuities in the value of this counter can occur at re-initialization of the management sy… |
| 1.3.6.1.2.1.122.1.2.1.13 | ColumnteTunnelPackets | read-only | current | The number of packets that have been forwarded over the Tunnel. Discontinuities in the value of this counter can occur at re-initialization of the management s… |
| 1.3.6.1.2.1.122.1.2.1.14 | ColumnteTunnelLPOctets | read-only | current | The number of octets that have been forwarded over the Tunnel. Discontinuities in the value of this counter can occur at re-initialization of the management sy… |
| 1.3.6.1.2.1.122.1.2.1.15 | ColumnteTunnelLPPackets | read-only | current | The number of packets that have been forwarded over the Tunnel. Discontinuities in the value of this counter can occur at re-initialization of the management s… |
| 1.3.6.1.2.1.122.1.2.1.16 | ColumnteTunnelAge | read-only | current | The age (i.e., time from creation of this conceptual row till now) of this Tunnel in hundredths of a second. Note that because TimeTicks wrap in about 16 month… |
| 1.3.6.1.2.1.122.1.2.1.17 | ColumnteTunnelTimeUp | read-only | current | The total time in hundredths of a second that this Tunnel has been operational. Note that because TimeTicks wrap in about 16 months, this value is best used in… |
| 1.3.6.1.2.1.122.1.2.1.18 | ColumnteTunnelPrimaryTimeUp | read-only | current | The total time in hundredths of a second that this Tunnel's primary path has been operational. Note that because TimeTicks wrap in about 16 months, this value … |
| 1.3.6.1.2.1.122.1.2.1.19 | ColumnteTunnelTransitions | read-only | current | The number of operational state transitions (up -> down and down -> up) this Tunnel has undergone. |
| 1.3.6.1.2.1.122.1.2.1.20 | ColumnteTunnelLastTransition | read-only | current | The time in hundredths of a second since the last operational state transition occurred on this Tunnel. Note that if the last transition was over 16 months ago… |
| 1.3.6.1.2.1.122.1.2.1.21 | ColumnteTunnelPathChanges | read-only | current | The number of path changes this Tunnel has had. |
| 1.3.6.1.2.1.122.1.2.1.22 | ColumnteTunnelLastPathChange | read-only | current | The time in hundredths of a second since the last path change occurred on this Tunnel. Note that if the last transition was over 16 months ago, this value will… |
| 1.3.6.1.2.1.122.1.2.1.23 | ColumnteTunnelConfiguredPaths | read-only | current | The number of paths configured for this Tunnel. |
| 1.3.6.1.2.1.122.1.2.1.24 | ColumnteTunnelStandbyPaths | read-only | current | The number of standby paths configured for this Tunnel. |
| 1.3.6.1.2.1.122.1.2.1.25 | ColumnteTunnelOperationalPaths | read-only | current | The number of operational paths for this Tunnel. This includes the path currently active, as well as operational standby paths. |
| 1.3.6.1.2.1.122.1.3 | TabletePathTable | not-accessible | current | Table of Configured Traffic Tunnels. |
| 1.3.6.1.2.1.122.1.3.1 | RowtePathEntry | not-accessible | current | Entry containing information about a particular Traffic Tunnel. Each Traffic Tunnel can have zero or more Traffic Paths. As a Traffic Path can only exist over … |
| 1.3.6.1.2.1.122.1.3.1.1 | ColumntePathIndex | not-accessible | current | An index that uniquely identifies a path within a Tunnel. The combination of <teTunnelIndex, tePathIndex> thus uniquely identifies a path among all paths on th… |
| 1.3.6.1.2.1.122.1.3.1.2 | ColumntePathName | read-create | current | The name of this path. A pathName must be unique within the set of paths over a single tunnel. If a SET request is received with a duplicate name, then the imp… |
| 1.3.6.1.2.1.122.1.3.1.3 | ColumntePathRowStatus | read-create | current | The status of this conceptual row. When the value of this object is 'active', then the value of tePathName cannot be changed. All other writable objects may be… |
| 1.3.6.1.2.1.122.1.3.1.4 | ColumntePathStorageType | read-create | current | The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. |
| 1.3.6.1.2.1.122.1.3.1.5 | ColumntePathType | read-create | current | The type for this PathEntry; i.e., whether this path is a primary path, a standby path, or a secondary path. |
| 1.3.6.1.2.1.122.1.3.1.6 | ColumntePathConfiguredRoute | read-create | current | The route that this TE path is configured to follow; i.e., an ordered list of hops. The value of this object gives the primary index into the Hop Table. The se… |
| 1.3.6.1.2.1.122.1.3.1.7 | ColumntePathBandwidth | read-create | current | The configured bandwidth for this Tunnel, in units of thousands of bits per second (Kbps). |
| 1.3.6.1.2.1.122.1.3.1.8 | ColumntePathIncludeAny | read-create | current | This is a configured set of administrative groups specified as a bit vector (i.e., bit n is 1 if group n is in the set, where n = 0 is the LSB). For each link … |
| 1.3.6.1.2.1.122.1.3.1.9 | ColumntePathIncludeAll | read-create | current | This is a configured set of administrative groups specified as a bit vector (i.e., bit n is 1 if group n is in the set, where n = 0 is the LSB). For each link … |
| 1.3.6.1.2.1.122.1.3.1.10 | ColumntePathExclude | read-create | current | This is a configured set of administrative groups specified as a bit vector (i.e., bit n is 1 if group n is in the set, where n = 0 is the LSB). For each link … |
| 1.3.6.1.2.1.122.1.3.1.11 | ColumntePathSetupPriority | read-create | current | The setup priority configured for this path, with 0 as the highest priority and 7 as the lowest. |
| 1.3.6.1.2.1.122.1.3.1.12 | ColumntePathHoldPriority | read-create | current | The hold priority configured for this path, with 0 as the highest priority and 7 as the lowest. |
| 1.3.6.1.2.1.122.1.3.1.13 | ColumntePathProperties | read-create | current | The set of configured properties for this path, expressed as a bit map. For example, if the path supports 'make before break', then bit 2 is set. |
| 1.3.6.1.2.1.122.1.3.1.14 | ColumntePathOperStatus | read-only | current | The operational status of the path: unknown: down: Signaling failed. testing: Administratively set aside for testing. dormant: Not signaled (for a backup tunne… |
| 1.3.6.1.2.1.122.1.3.1.15 | ColumntePathAdminStatus | read-create | current | The operational status of the path: normal: Used normally for forwarding. testing: Administratively set aside for testing. |
| 1.3.6.1.2.1.122.1.3.1.16 | ColumntePathComputedRoute | read-only | current | The route computed for this path, perhaps using some form of Constraint-based Routing. The algorithm is implementation dependent. This object returns the compu… |
| 1.3.6.1.2.1.122.1.3.1.17 | ColumntePathRecordedRoute | read-only | current | The route actually used for this path, as recorded by the signaling protocol. This is again an ordered list of hops; each hop is expected to be strict. The val… |
| 1.3.6.1.2.1.122.1.4 | TabletePathHopTable | not-accessible | current | Table of Tunnel Path Hops. |
| 1.3.6.1.2.1.122.1.4.1 | RowtePathHopEntry | not-accessible | current | Entry containing information about a particular hop. |
| 1.3.6.1.2.1.122.1.4.1.1 | ColumnteHopListIndex | not-accessible | current | An index that identifies a list of hops. This is the primary index to access hops. |
| 1.3.6.1.2.1.122.1.4.1.2 | ColumntePathHopIndex | not-accessible | current | An index that identifies a particular hop among the list of hops for a path. An index of i identifies the ith hop. This is the secondary index for a hop entry. |
| 1.3.6.1.2.1.122.1.4.1.3 | ColumntePathHopRowStatus | read-create | current | The status of this conceptual row. Any field in this table can be changed, even if the value of this object is 'active'. However, such a change may cause traff… |
| 1.3.6.1.2.1.122.1.4.1.4 | ColumntePathHopStorageType | read-create | current | The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. |
| 1.3.6.1.2.1.122.1.4.1.5 | ColumntePathHopAddrType | read-create | current | The type of Traffic Engineered Tunnel hop Address of this hop. The value of this object cannot be changed if the value of the corresponding tePathRowStatus obj… |
| 1.3.6.1.2.1.122.1.4.1.6 | ColumntePathHopAddress | read-create | current | The Traffic Engineered Tunnel hop Address of this hop. The type of this address is determined by the value of the corresponding tePathHopAddressType. The value… |
| 1.3.6.1.2.1.122.1.4.1.7 | ColumntePathHopType | read-only | current | The type of hop: unknown: loose: This hop is a LOOSE hop. strict: This hop is a STRICT hop. |
| 1.3.6.1.2.1.122.2 | NodeteMIBConformance | |||
| 1.3.6.1.2.1.122.2.1 | NodeteGroups | |||
| 1.3.6.1.2.1.122.2.1.1 | GroupteTrafficEngineeringGroup | current | Objects for Traffic Engineering in this MIB module. | |
| 1.3.6.1.2.1.122.2.1.2 | GroupteNotificationGroup | current | Notifications specified in this MIB module. | |
| 1.3.6.1.2.1.122.2.2 | NodeteModuleCompliance | |||
| 1.3.6.1.2.1.122.2.2.1 | ComplianceteModuleReadOnlyCompliance | read-only | current | When this MIB module is implemented without support for read-create (i.e., in read-only mode), then such an implementation can claim read-only compliance. Such… |
| 1.3.6.1.2.1.122.2.2.2 | ComplianceteModuleFullCompliance | current | When this MIB module is implemented with support for read-create, then the implementation can claim full compliance. Such devices can be both monitored and con… | |
| 1.3.6.1.2.1.122.2.2.3 | ComplianceteModuleServerReadOnlyCompliance | read-only | current | When this MIB module is implemented by a path computation server without support for read-create (i.e., in read-only mode), then the implementation can claim r… |
| 1.3.6.1.2.1.122.2.2.4 | ComplianceteModuleServerFullCompliance | current | When this MIB module is implemented by a path computation server with support for read-create, then the implementation can claim full compliance. |