TN-TC-MIB
406 objects
This document is the SNMP MIB module for the SNMP Textual Conventions (TCs) used in the Nokia SROS manageability instrumentation. This SNMP MIB module (Specification) embodies Nokia's proprietary intellectual property. Nokia retains all title and ownership in the Specification, including any revisions. Nokia grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Nokia products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied `as is', and Nokia makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
Imported Objects
| SNMPv2-SMI | Integer32 MODULE-IDENTITY Unsigned32 |
| SNMPv2-TC | DisplayString TEXTUAL-CONVENTION |
| TROPIC-GLOBAL-REG | tnModules |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.7483.5.1.2 | IdentitytnTCMIBModule | This document is the SNMP MIB module for the SNMP Textual Conventions (TCs) used in the Nokia SROS manageability instrumentation. This SNMP MIB module (Specifi… |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| BgpPeeringStatus | INTEGER { notApplicable (0), installed (1), notInstalled (2), noEnhancedSubmgt (3), wrongAntiSpoof (4), parentItfDown (5), hostInactive (6), noDualHomingSupport (7), invalidRadiusAttr (8), noDynamicPeerGroup (9), duplicatePeer (10), maxPeersReached (11), genError (12) } | current | The status of the BGP peering session. |
| Dot1PPriority | Integer32 (-1 | 0..7) | current | IEEE 802.1p priority. zero is lowest, seven is highest. -1 means not set |
| Dot1PPriorityMask | Integer32 (0..7) | current | IEEE 802.1p priority mask. zero is lowest, seven is highest. |
| InterfaceIndex | Integer32 | current | A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub- layer must r… |
| IpAddressPrefixLength | Integer32 (0..32) | current | the number of bits to match in an IP address mask. |
| QTag | Integer32 (1..4094) | current | The QTag data type is a 12-bit integer tag used to identify a service. The values 0 and 4095 are not allowed. |
| QTagFullRange | Unsigned32 (0..4095) | current | The data type QTagFullRange represents a VLAN tag. A VLAN tag is 12 bits is size. The data type QTagFullRange covers the whole range of possible values. (0..4095 or 0x0 .. 0xFFF) |
| QTagFullRangeOrNone | Integer32 (-1 | 0..4095) | current | The data type QTagFullRangeOrNone represents a VLAN tag. A VLAN tag is 12 bits is size. The data type QTagFullRange covers the whole range of possible values. (0..4095 or 0x0 .. 0xFFF). The value '-1' indicates the abse… |
| QTagOrZero | Unsigned32 (0..4094) | current | The data type QTagOrZero represents a VLAN tag. The value '0' indicates that no VLAN tag is provisioned, or that its value is unknown. |
| SapLoopbackMode | INTEGER { disabled(1), terminal(2), facility(3) } | current | SapLoopbackMode data type is an enumerated integer that describes the values used to identify the loopback mode of a sap. |
| SdpBindId | OCTET STRING (SIZE (8)) | current | The value used to uniquely identify an SDP Binding. The first four octets correspond to the zero-extended 16-bit SDP ID, while the remaining four octets correspond to the 32-bit VC ID, both encoded in network byte order. |
| ServiceAccessPoint | Integer32 (-1 | 0..255) | current | 802.2 LLC SAP value, Source and Destination. |
| ServiceAdminStatus | INTEGER { up(1), down(2) } | current | ServiceAdminStatus data type is an enumerated integer that describes the values used to identify the administrative state of a service. |
| ServiceOperStatus | INTEGER { up(1), down(2) } | current | ServiceOperStatus data type is an enumerated integer that describes the values used to identify the current operational state of a service. |
| ServObjDesc | DisplayString (SIZE (0..80)) | current | ASCII string used to describe various service objects. |
| TAdaptationRule | INTEGER { max (1), min (2), closest(3) } | current | The adaptation rule to be applied to calcluate the operational values for the specified entity. |
| TAdaptationRuleOverride | INTEGER { noOverride (0), max (1), min (2), closest (3) } | current | The adaptation rule to be applied to calcluate the operational values for the specified entity. |
| TAdvCfgRate | Integer32 (0..100000000) | current | The PIR rate to be used in kbps. |
| TAtmTdpDescrType | INTEGER { clp0And1pcr(0), clp0And1pcrPlusClp0And1scr(1), clp0And1pcrPlusClp0scr(2), clp0And1pcrPlusClp0scrTag(3) } | current | The TAtmTdpDescrType is an enumerated integer whose value indicates the types of cell loss priority to be used in conjunction with traffic parameters. The following values are outlined: Integer Value Interpretation clp0… |
| TBurstHundredthsOfPercent | Integer32 (0..10000) | current | The percentage of buffer space assigned to a queue that is reserved for some purpose, defined to two decimal places. |
| TBurstLimit | Integer32 (-1 | 1..14000000) | current | An explicit shaping burst size for a queue. The value of -1 specifies system default value. |
| TBurstPercent | Integer32 (0..100) | current | The percentage of buffer space assigned to a queue that is reserved for some purpose. |
| TBurstPercentOrDefault | Integer32 (-1 | 0..100) | current | The percentage of buffer space assigned to a queue that is reserved for some purpose. The value -1 means that the actual value is derived from the corresponding buffer policy's default value. |
| TBurstPercentOrDefaultOverride | Integer32 (-2 | -1 | 0..100) | current | The percentage of buffer space assigned to a queue that is reserved for some purpose. The value -1 means that the actual value is derived from the corresponding buffer policy's default value. A value of -2 specifies no … |
| TBurstSize | Integer32 (-1 | 0..131072) | current | The amount of buffer space (in kbytes) assigned to a queue. The value -1 means that the actual value is derived from the corresponding buffer policy's default value. |
| TBurstSizeBytes | Integer32 (-1 | 0..134217728) | current | The amount of buffer space (in bytes) assigned to a queue. The value -1 means that the actual value is derived from the corresponding buffer policy's default value. |
| TBurstSizeBytesOverride | Integer32 (-2 | -1 | 0..134217728) | current | The amount of buffer space (in bytes) assigned to a queue. The value -1 means that the actual value is derived from the corresponding buffer policy's default value. A value of -2 specifies no override. |
| TBurstSizeOverride | Integer32 (-2 | -1 | 0..131072) | current | The amount of buffer space (in kbytes) assigned to a queue. The value -1 means that the actual value is derived from the corresponding buffer policy's default value. A value of -2 specifies no override. |
| TBWRateType | INTEGER { kbps (1), percentPortLimit (2), percentLocalLimit (3) } | current | The type of the PIR/CIR percent rate. The value 'kbps' means the rate is specified in kbps. The value 'percentPortLimit' means the rate is specified in percentage of port limit. The value 'percentLocalLimit' means the r… |
| TCIRPercentOverride | Integer32 (-2 | 0..10000) | current | The CIR percentage rate specified in hundredths of a percent. A value of -2 specifies no override. |
| TCIRRate | Integer32 (-1 | 0..100000000) | current | The CIR rate to be used in kbps. The value -1 means maximum rate. |
| TCIRRateOverride | Integer32 (-2 | -1 | 0..100000000) | current | The CIR rate to be used in kbps. The value -1 means maximum rate. A value of -2 specifies no override. |
| TClassBurstLimit | Integer32 (-1|1..327680) | current | An explicit shaping burst size for a class. The value -1 means that the actual value is derived from the corresponding class's default value. |
| TCpmProtPolicyID | Unsigned32 (0..255) | current | The data type TCpmProtPolicyID represents the identification number of a CPM Protection policy. The value '0' indicates that no CPM Protection policy is provisioned. |
| TCpmProtPolicyIDOrDefault | Integer32 (-1 | 1..255) | current | The data type TCpmProtPolicyIDOrDefault represents the identification number of a CPM Protection policy. The value of '-1' indicates the system determined default value. |
| TDEProfile | INTEGER { in (1), out (2), de (3) } | current | This textual-convention specifies the profile marking of a packet. Value of 'in' specifies the in-profile marking. Value of 'out' specifies the out-profile marking. Value of 'de' specifies that the profile marking will … |
| TDEProfileOrDei | INTEGER { in (1), out (2), de (3), use-dei (13) } | current | This textual-convention specifies the profile marking of a packet. Value of 'in' specifies the in-profile marking. Value of 'out' specifies the out-profile marking. Value of 'de' specifies that the profile marking will … |
| TDEValue | Integer32 (-1 | 0..1) | current | This textual-convention specifies the DE (Drop Eligible) bit value. The value of '-1' means DE value is not specified. |
| TDirection | INTEGER { both (0), ingress(1), egress (2) } | current | TDirection denotes a direction. |
| TDSCPFilterActionValue | Integer32 (-1 | 0..255) | current | The value of a Differential Services Code Point. -1 means not set. |
| TDSCPName | TNamedItem | current | The name of a Differential Services Code Point value. |
| TDSCPNameOrEmpty | TNamedItemOrEmpty | current | The name of a Differential Services Code Point value. |
| TDSCPValue | Integer32 (0..63) | current | The value of a Differential Services Code Point. |
| TDSCPValueOrNone | Integer32 (-1 | 0..63) | current | The value of a Differential Services Code Point (DSCP). A value of -1 means that no DSCP value is configured or available. |
| TEgressHsmdaCounterId | Unsigned32 (1..8) | current | The identifcation number of a HSMDA egress counter. |
| TEgressHsmdaCounterIdOrZero | Unsigned32 (0|1..8) | current | The identifcation number of a HSMDA egress counter. The value 0 indicates an undefined counter id. |
| TEgressHsmdaPerPacketOffset | Integer32 (-32..31) | current | The value, in bytes, of the adjustment to make to the size of each outgoing packet for accounting. |
| TEgressHsmdaQueueId | Integer32 (0 | 1..8) | current | The value of TEgressHsmdaQueueId specifies the identification number of a HSMDA egress queue. A value of zero (0) indicates that no specific queue identification has been assigned for this object. When an object of type… |
| TEgressQPerPacketOffset | Integer32 (-64..32) | current | The value, in bytes, of the adjustment to make to the size of each packet for accounting. |
| TEgressQueueId | Integer32 (0 | 1..8) | current | The value of TEgressQueueId specifies the identification number of an egress queue. A value of zero (0) indicates that no specific queue identification has been assigned for this object. When an object of type TEgressQu… |
| TEgrHsmdaPerPacketOffsetOvr | Integer32 (-128 | -32..31) | current | The value, in bytes, of the override of the adjustment to make to the size of each outgoing packet for accounting. A value of -128 indicates no override. |
| TEgrPolicerId | Integer32 (1..8) | current | The data type describes the QoS control policer identifier on egress side. |
| TEgrPolicerIdOrNone | Integer32 (0|1..8) | current | The data type describes the QoS control policer identifier on egress side or zero when not specified. |
| TEgrRateModType | INTEGER { none (1), aggRateLimit (2), namedScheduler (3) } | current | The data type TEgrRateModType represents the type of egress-rate modification that is to be applied. |
| TEntryId | TEntryIndicator (1..65535) | current | uniquely identifies an entry in a policy or filter table. to facilitate insertion of entries in the tables, we recommend assigning entry IDs by 10s: 10, 20, 30, etc. |
| TEntryIndicator | Unsigned32 (0..65535) | current | Uniquely identifies an entry in a policy or filter table. The value 0 is not a valid entry-id. When used as insertion point the value 0 indicates that entries must be inserted at the very beginning, i.e.before the first… |
| TExpSecondaryShaperClassRate | Integer32 (-1 | 1..10000000) | current | The expanded secondary shaper class PIR rate to be used in Kbps. The value -1 means maximum rate. |
| TExpSecondaryShaperPIRRate | Integer32 (-1 | 1..10000000) | current | The expanded secondary shaper PIR rate to be used in Kbps. The value -1 means maximum rate. |
| TFCName | TNamedItem | current | The name of a Forwarding Class entry. |
| TFCNameOrEmpty | TNamedItemOrEmpty | current | The name of a Forwarding Class entry. |
| TFCSet | BITS { be (0), l2 (1), af (2), l1 (3), h2 (4), ef (5), h1 (6), nc (7) } | current | This data type describes a set of Forwarding Classes. |
| TFCType | INTEGER { be (0), l2 (1), af (2), l1 (3), h2 (4), ef (5), h1 (6), nc (7) } | current | This data type enumerates the Forwarding Classes. |
| TFdbTableSizeProfileID | Unsigned32 (1..7) | current | The identification number of a Fdb Table Size profile. |
| TFilterID | Unsigned32 (0..65535) | current | the identification number of a filter. 0 indicates an invalid filter-id. |
| TFIRRate | Integer32 (-1 | 1..100000000) | current | The static fair rate to be used in kbps. The value -1 means maximum rate. |
| TFrameType | INTEGER { e802dot3(0), e802dot2LLC(1), e802dot2SNAP(2), ethernetII(3), atm(5) } | current | The type of the frame for which this mac filter match criteria is defined. |
| THPolCIRRate | Integer32 (-1 | 0..20000000) | current | The CIR rate to be used in kbps. The value -1 means maximum rate. |
| THPolCIRRateOverride | Integer32 (-2 | -1 | 0..20000000) | current | The CIR rate to be used in kbps. The value -1 means maximum rate. A value of -2 specifies no override. |
| THPolPIRRate | Integer32 (-1 | 1..20000000) | current | The PIR rate to be used in kbps. The value -1 means maximum rate. |
| THPolPIRRateOverride | Integer32 (-2 | -1 | 1..20000000) | current | The PIR rate to be used in kbps. The value -1 means maximum rate. A value of -2 specifies no override. |
| THPolVirtualScheCIRRate | Integer32 (-1 | 0..800000000) | current | The CIR rate to be used in kbps. The value -1 means maximum rate. |
| THPolVirtualSchePIRRate | Integer32 (-1 | 1..800000000) | current | The PIR rate to be used in kbps. The value -1 means maximum rate. |
| THSMDABurstSizeBytes | Integer32 (-1 | 0..2688000) | current | The amount of buffer space (in bytes) assigned to a HSMDA queue. The value -1 means that the actual value is derived from the corresponding buffer policy's default value. |
| THSMDABurstSizeBytesOverride | Integer32 (-2 | -1 | 0..2688000) | current | The amount of buffer space (in bytes) assigned to a HSMDA queue. The value -1 means that the actual value is derived from the corresponding buffer policy's default value. A value of -2 specifies no override. |
| THsmdaCIRKRate | Integer32 (-1 | 0..100000000) | current | The HSMDA CIR rate to be used in Kbps. The value -1 means maximum rate. |
| THsmdaCIRKRateOverride | Integer32 (-2 | -1 | 0..100000000) | current | The HSMDA CIR rate to be used in Kbps. The value -1 means maximum rate. A value of -2 specifies no override. |
| THsmdaCIRMRate | Integer32 (-1 | 0..100000) | current | The HSMDA CIR rate to be used in Mbps. The value -1 means maximum rate. |
| THsmdaCIRMRateOverride | Integer32 (-2 | -1 | 0..100000) | current | The HSMDA CIR rate to be used in Mbps. The value -1 means maximum rate. A value of -2 specifies no override. |
| THsmdaCounterIdOrZero | Unsigned32 (0|1..8) | current | The identifcation number of a HSMDA counter. The value 0 indicates an undefined counter id. |
| THsmdaCounterIdOrZeroOrAll | Integer32 (-1 | 0 | 1..8) | current | The identifcation number of a HSMDA counter. The value (0) indicates an undefined counter id. The value (-1) is used to indicate all counters. |
| THsmdaPIRKRate | Integer32 (-1 | 1..100000000) | current | The HSMDA PIR rate to be used in Kbps. The value -1 means maximum rate. |
| THsmdaPIRKRateOverride | Integer32 (-2 | -1 | 1..100000000) | current | The HSMDA PIR rate to be used in Kbps. The value -1 means maximum rate. A value of -2 specifies no override. |
| THsmdaPIRMRate | Integer32 (-1 | 1..100000) | current | The HSMDA PIR rate to be used in Mbps. The value -1 means maximum rate. |
| THsmdaPIRMRateOverride | Integer32 (-2 | -1 | 1..100000) | current | The HSMDA PIR rate to be used in Mbps. The value -1 means maximum rate. A value of -2 specifies no override. |
| THsmdaPolicyIncludeQueues | INTEGER { q1to2 (1), q1to3 (2) } | current | The value of THsmdaPolicyIncludeQueues specifies which queues are to be scheduled in the same class in a HSMDA scheduler. |
| THsmdaPolicyScheduleClass | Integer32 (1..3) | current | The value of THsmdaPolicyScheduleClass the class at which the queues specified by THsmdaPolicyIncludeQueues in a HSMDA scheduler. |
| THSMDAQueueBurstLimit | Integer32 (-1 | 1..1000000) | current | An explicit shaping burst size of a HSMDA queue. The value -1 means that the actual value is derived from the corresponding queue's default value. |
| THsmdaSchedulerPolicyGroupId | Integer32 (0 | 1..2) | current | The value of THsmdaSchedulerPolicyGroupId specifies the identification number of a HSMDA scheduler policy group. A value of zero (0) indicates that no specific group identification has been assigned for this object. Whe… |
| THsmdaWeight | Integer32 (1..100) | current | The weight of the specified HSMDA entity while feeding into the parent. |
| THsmdaWeightClass | INTEGER { class1 (1), class2 (2), class4 (4), class8 (8) } | current | The weight of the specified HSMDA entity while feeding into the parent. |
| THsmdaWeightOverride | Integer32 (-2 | 1..100) | current | The weight of the specified HSMDA entity while feeding into the parent. A value of -2 specifies no override. |
| THsmdaWrrWeight | Integer32 (1..32) | current | The weight of the specified HSMDA entity while feeding into the parent. |
| THsmdaWrrWeightOverride | Integer32 (-2 | 1..32) | current | The weight of the specified HSMDA entity while feeding into the parent. A value of -2 specifies no override. |
| TIngHsmdaPerPacketOffsetOvr | Integer32 (-128 | -32..31) | current | The value, in bytes, of the override of the adjustment to make to the size of each incoming packet for accounting. A value of -128 indicates no override. |
| TIngPolicerId | Integer32 (1..32) | current | The data type describes the QoS control policer identifier on ingress side. |
| TIngPolicerIdOrNone | Integer32 (0|1..32) | current | The data type describes the QoS control policer identifier on ingress side or zero when not specified. |
| TIngressHsmdaCounterId | Unsigned32 (1..8) | current | The identifcation number of a HSMDA ingress counter. |
| TIngressHsmdaCounterIdOrZero | Unsigned32 (0|1..8) | current | The identifcation number of a HSMDA ingress counter. The value 0 indicates an undefined counter id. |
| TIngressHsmdaPerPacketOffset | Integer32 (-32..31) | current | The value, in bytes, of the adjustment to make to the size of each incoming packet for accounting. |
| TIngressHsmdaQueueId | Integer32 (0 | 1..8) | current | The value of TIngressHsmdaQueueId specifies the identification number of a HSMDA ingress queue. A value of zero (0) indicates that no specific queue identification has been assigned for this object. When an object of ty… |
| TIngressMeterId | Integer32 (0 | 1..32) | current | Ingress Meter Id |
| TIngressQueueId | Integer32 (0 | 1..32) | current | The value of TIngressQueueId specifies the identification number of an ingress queue. A value of zero (0) indicates that no specific queue identification has been assigned for this object. When an object of type TIngres… |
| TIPFilterID | Unsigned32 (0..65535) | current | the identification number of an IP filter. |
| TIpOption | Integer32 (0..255) | current | IP packet options octet. explanation of the octet bits: IP OPTION NUMBERS The Internet Protocol (IP) has provision for optional header fields identified by an option type field. Options 0 and 1 are exactly one octet whi… |
| TIpProtocol | Integer32 (-2 | -1 | 0..255) | current | IP protocol number. well known protocol numbers include ICMP(1), TCP(6), UDP(17). -1 means value not set. -2 indicates protocol wildcard for UDP and TCP. |
| TItemDescription | DisplayString (SIZE(0..80)) | current | Description for an item. Note, use only NVT ASCII displayable characters here, no control characters, no UTF-8, etc. |
| TItemLongDescription | DisplayString (SIZE(0..160)) | current | Longer description for an item. Note, use only NVT ASCII displayable characters here, no control characters, no UTF-8, etc. |
| TItemMatch | INTEGER { off(1), false(2), true(3) } | current | when set to off, the item is not matched. when set to false, packets without the item match the filter. when set to true, packets with the item match the filter. |
| TItemScope | INTEGER { exclusive(1), template(2) } | current | This textual-convention determines some aspects of an item's behavior regarding creation and use, unused entry garbage collection, and automated promulgation by Element Management System to other systems in the service … |
| TLevel | Integer32 (1..8) | current | The level of the specified entity while feeding into the parent. |
| TLevelOrDefault | Integer32 (0|1..8) | current | The level of the specified entity while feeding into the parent. The value 0 is used to denote a default value. |
| TLNamedItem | DisplayString (SIZE (1..64)) | current | The long name of an item. When used as an index to a table, the item name uniquely identifies the instance. When used in a reference (TLNamedItemOrEmpty) the item name entry must exist in the table. Note, use only NVT A… |
| TLNamedItemOrEmpty | DisplayString (SIZE (0 | 1..64)) | current | The long name of an item, or an empty string. When used in a reference (TLNamedItemOrEmpty) the item name entry must exist in the table. Note, use only NVT ASCII displayable characters here, no control characters, no UT… |
| TLspExpValue | Integer32 (-1 | 0..7) | current | MPLS Experimental bits. -1 means not set. |
| TMACFilterID | Unsigned32 (0..65535) | current | the identification number of a MAC filter. |
| TMacFilterType | INTEGER { normal(1), isid (2), vid (3) } | current | A type containing the possible types of MAC filters provided by the system |
| TMatchCriteria | INTEGER { ip(1), mac(2), none(3),dscp(4), dot1p(5), prec(6) } | current | determines whether the entry matches traffic using IP match entries or MAC match entries. |
| TMaxDecRate | Integer32 (0 | 1..100000000) | current | The Advanced Configuration policy Max-Decrement rate to be used in kbps. |
| TMcFrQoSProfileId | Unsigned32 (0..65535) | current | This textual-convention uniquely identifies Multi-class Frame-relay QoS profiles in the ingress and egress multi-class frame-relay QoS profile tables. The value 0 indicates a default QoS Profile as applicable to a given… |
| TMeterMode | INTEGER { priority(1), profile (2) } | current | Meter Mode |
| TMlpppQoSProfileId | Unsigned32 (0..65535) | current | This textual-convention uniquely identifies MLPPP Bundle QoS profile in the ingress and egress MLPPP QoS profile tables. The value 0 indicates default MLPPP QoS Profile as applicable to a given H/W |
| TmnxAccessLoopEncapDataLink | INTEGER { aal5 (0), ethernet (1) } | current | The data type TmnxAccessLoopEncapDataLink specifies the data link used by the subscriber on the DSL access loop. |
| TmnxAccessLoopEncaps1 | INTEGER { notAvailable (0), untaggedEthernet (1), singleTaggedEthernet (2) } | current | The data type TmnxAccessLoopEncaps1 specifies the encapsulation used by the subscriber on the DSL access loop. |
| TmnxAccessLoopEncaps2 | INTEGER { notAvailable (0), pppoaLlc (1), pppoaNull (2), ipoaLlc (3), ipoaNull (4), ethernetOverAal5LlcFcs (5), ethernetOverAal5LlcNoFcs (6), ethernetOverAal5NullFcs (7), ethernetOverAal5NullNoFcs (8) } | current | The data type TmnxAccessLoopEncaps2 specifies the encapsulation used by the subscriber on the DSL access loop. |
| TmnxAccPlcyAACounters | BITS { any (0), sfa (1), nfa (2), sfd (3), nfd (4), saf (5), naf (6), spa (7), npa (8), sba (9), nba (10), spd (11), npd (12), sbd (13), nbd (14), sdf (15), mdf (16), ldf (17), tfd (18), tfc (19), sbm (20), spm (21), smt (22), nbm (23), npm (24), nmt (25) } | current | This data type describes a set of AA (Application Assurance) counters for which accounting data can be collected. |
| TmnxAccPlcyOECounters | BITS { ipf (0), ipd (1), opf (2), opd (3), iof (4), iod (5), oof (6), ood (7) } | current | This data type describes a set egress counters for which accounting data can be collected associated with a given counter. |
| TmnxAccPlcyOICounters | BITS { apo (0), aoo (1), hpd (2), lpd (3), hod (4), lod (5), ipf (6), opf (7), iof (8), oof (9) } | current | This data type describes a set ingress counters for which accounting data can be collected associated with a given counter. |
| TmnxAccPlcyQECounters | BITS { ipf (0), ipd (1), opf (2), opd (3), iof (4), iod (5), oof (6), ood (7) } | current | This data type describes a set egress counters for which accounting data can be collected associated with a given queue. |
| TmnxAccPlcyQICounters | BITS { hpo (0), lpo (1), ucp (2), hoo (3), loo (4), uco (5), apo (6), aoo (7), hpd (8), lpd (9), hod (10), lod (11), ipf (12), opf (13), iof (14), oof (15) } | current | This data type describes a set ingress counters for which accounting data can be collected associated with a given queue. |
| TmnxActionType | INTEGER { doAction (1), notApplicable (2) } | current | The TmnxActionType data type is an enumerated integer that describes the values used to support action or operation style commands. Setting a variable of this type to 'doAction' causes the action to occur. GETs and GETN… |
| TmnxAdminState | INTEGER { noop (1), inService (2), outOfService (3) } | current | The TmnxAdminState data type is an enumerated integer that describes the values used to identify the administratively desired state of functional modules. |
| TmnxAiiType | INTEGER { aiiType1 (1), aiiType2 (2) } | current | TmnxAiiType indicates LDP FEC 129 Attachment Individual Identifier (AII) type. |
| TmnxAncpString | DisplayString (SIZE (1..63)) | current | The TmnxAncpString data type contains a valid ancp string. |
| TmnxAncpStringOrZero | DisplayString (SIZE (0..63)) | current | The TmnxAncpStringOrZero data type contains a valid ancp string. An empty string indicates that no ANCP string is defined. |
| TmnxAppProfileString | DisplayString (SIZE (1..16)) | current | The data type TmnxAppProfileString denotes the application profile string. |
| TmnxAppProfileStringOrEmpty | DisplayString (SIZE (0..16)) | current | The data type TmnxAppProfileStringOrEmpty denotes the application profile string. The empty string denotes the absence of a application profile. |
| TmnxAsciiSpecification | DisplayString (SIZE (0..255)) | current | The data type TmnxAsciiSpecification is a format string that specifies how to form a target ASCII string. The format is as follows: <ascii-specification> ::= <char-specification>+ <char-specification> ::= <ascii-char> |… |
| TmnxBfdSessOperState | INTEGER { unknown (1), connected (2), broken (3), peerDetectsDown(4), notConfigured (5), noResources (6) } | current | The TmnxBfdSessOperState data type is an enumerated integer that describes the values used to identify the operational state of a BFD session the instance is relying upon for its fast triggering mechanism. |
| TmnxBgpAutonomousSystem | Integer32 (0..65535) | current | an autonomous system (AS) number. |
| TmnxBGPFamilyType | BITS { ipv4Unicast (0), ipv4Multicast (1), ipv4UastMcast (2), ipv4MplsLabel (3), ipv4Vpn (4), ipv6Unicast (5), ipv6Multicast (6), ipv6UcastMcast (7), ipv6MplsLabel (8), ipv6Vpn (9), l2Vpn (10), ipv4Mvpn (11), msPw (12), ipv4Flow (13), mdtSafi (14), routeTarget (15), mcastVpnIpv4 (16) } | current | The value of TmnxBGPFamilyType specifies the AFI-SAFI family for BGP peer. |
| TmnxBgpLocalPreference | Unsigned32 | current | a local route preference value. |
| TmnxBgpPreference | Unsigned32 (0..255) | current | a route preference value. |
| TmnxBgpRouteTarget | OCTET STRING (SIZE(1..32)) | current | TmnxBgpRouteTarget is an readable string that specifies the extended community name to be accepted by a Route Reflector Server or advertised by the router when reflecting any routes. I.e, it does not apply to routes tha… |
| TmnxBinarySpecification | DisplayString (SIZE (0..255)) | current | The data type TmnxBinarySpecification is a string of ASCII characters that specifies how to form a binary number. The format is as follows: <binary-specification> ::= <bit-specification>+ <bit-specification> ::= '0' | '… |
| TmnxBsxAarpId | Unsigned32 (1..65535) | current | TmnxBsxAarpId identifies an instance of the AA Redundancy Protocol (AARP). |
| TmnxBsxAarpIdOrZero | Unsigned32 (0 | 1..65535) | current | TmnxBsxAarpIdOrZero identifies an instance of the AA Redundancy Protocol (AARP). The value of '0' indicates an invalid AARP instance. |
| TmnxBsxAarpServiceRefType | INTEGER { none (0), dualHomed (1), shuntSubscriberSide (2), shuntNetworkSide (3) } | current | TmnxBsxAarpServiceRefType identifies the role of the SAP or Spoke SDP service point being referenced by an AARP instance. This reference is made in the context of a AARP instance identified by TmnxBsxAarpIdOrZero. The s… |
| TmnxBsxTransitIpPolicyId | Unsigned32 (1..65535) | current | TmnxBsxTransitIpPolicyId identifies a transit IP policy. |
| TmnxBsxTransitIpPolicyIdOrZero | Unsigned32 (0 | 1..65535) | current | TmnxBsxTransitIpPolicyId identifies a transit ip policy. The value '0' indicates an invalid transit IP policy. |
| TmnxBsxTransPrefPolicyId | Unsigned32 (1..65535) | current | TmnxBsxTransPrefPolicyId identifies a transit prefix policy. |
| TmnxBsxTransPrefPolicyIdOrZero | Unsigned32 (0 | 1..65535) | current | TmnxBsxTransPrefPolicyId identifies a transit prefix policy. The value '0' indicates an invalid transit prefix policy. |
| TmnxCdrDiagnosticAction | INTEGER { included (1), excluded (2) } | current | The TmnxCdrDiagnosticAction is an enumerated integer that describes whether the Diagnostics should be included or excluded in the Charging Data Record (CDR). |
| TmnxCdrType | INTEGER { pgwCdr (1), gCdr (2), eGCdr (3) } | current | The TmnxCdrType is an enumerated integer that describes the current charging type in Charging Data Record (CDR). pgwCdr - indicates Packet data network Gateway CDR gCdr - indicates Gateway GPRS Support Node (GGSN) CDR, … |
| TmnxCustId | Unsigned32 (0|1..2147483647) | current | A number used to identify a Customer or Subscriber. This ID must be unique within the Service Domain. The value 0 is used as the null ID. |
| TmnxDefInterDestIdSource | INTEGER { useString (1), useTopQTag (2), useVpi (3) } | current | The data type TmnxDefInterDestIdSource specifies what will be used as the default intermediate destination identifier. This value is used in case no other source (like RADIUS) provides an intermediate destination identi… |
| TmnxDefSubIdSource | INTEGER { useSapId (1), useString (2), useAutoId (3) } | current | The data type TmnxDefSubIdSource specifies what will be used as the default subscriber identification. This value is used in case no other source (like RADIUS) provides a subscriber identification string. If the value o… |
| TmnxDHCP6MsgType | INTEGER { dhcp6MsgTypeSolicit (1), dhcp6MsgTypeAdvertise (2), dhcp6MsgTypeRequest (3), dhcp6MsgTypeConfirm (4), dhcp6MsgTypeRenew (5), dhcp6MsgTypeRebind (6), dhcp6MsgTypeReply (7), dhcp6MsgTypeRelease (8), dhcp6MsgTypeDecline (9), dhcp6MsgTypeReconfigure (10), dhcp6MsgTypeInfoRequest (11), dhcp6MsgTypeRelayForw (12), dhcp6MsgTypeRelayReply (13), dhcp6MsgTypeMaxValue (14) } | current | The DHCP6 messagetype. |
| TmnxDhcpOptionType | INTEGER { ipv4(1), ascii(2), hex(3), ipv6(4), domain(5) } | current | The data type TmnxDhcpOptionType represents how the value of this option is encoded: - 'ipv4 (1)' : this option contains an IPv4 address (4 octets) - 'ascii(2)' : this option contains seven-bit ASCII characters - 'hex (… |
| TmnxEgrPolicerStatMode | INTEGER { noStats (0), minimal (1), offeredProfileNoCIR (2), offeredTotalCIR (3), offeredProfileCIR (4), offeredLimitedCapCIR(5), offeredProfileCapCIR(6) } | current | TmnxEgrPolicerStatMode specifies the mode of statistics collected by this egress policer. |
| TmnxEgrPolicerStatModeOverride | INTEGER { noOverride (-1), noStats (0), minimal (1), offeredProfileNoCIR (2), offeredTotalCIR (3), offeredProfileCIR (4), offeredLimitedCapCIR(5), offeredProfileCapCIR(6) } | current | TmnxEgrPolicerStatModeOverride specifies the override mode of statistics collected by this egress policer. |
| TmnxEnabledDisabled | INTEGER { enabled (1), disabled (2) } | current | The TmnxEnabledDisabled data type is an enumerated integer that describes the values used to identify whether an entity is 'enabled' or 'disabled'. |
| TmnxEnabledDisabledOrInherit | INTEGER { enabled (1), disabled (2), inherit (3) } | current | The TmnxEnabledDisabledOrInherit data type is an enumerated integer that describes the values used to identify whether an entity is 'enabled', 'disabled' or inherits its state from another object that is usually in anot… |
| TmnxEncapVal | Unsigned32 | current | The value of the label used to identify the entity using the specified encapsulation value on a specific port. The format of this object depends on the encapsulation type defined on this port. When the encapsulation is … |
| TmnxFilterProfileStringOrEmpty | DisplayString (SIZE (0..16)) | current | The data type TmnxFilterProfileStringOrEmpty denotes the filter profile string. The empty string denotes the absence of a filter profile. |
| TmnxIgmpGroupFilterMode | INTEGER { include (1), exclude (2) } | current | The data type TmnxIgmpGroupFilterMode describes the filter-mode of a group. In 'include(1)' mode, reception of packets sent to the specified multicast address is requested only from those IPv4 Source addresses listed in… |
| TmnxIgmpGroupType | INTEGER { static(1), dynamic(2) } | current | The data type TmnxIgmpGroupType describes how a multicast group is learned. |
| TmnxIgmpVersion | INTEGER { version1(1), version2(2), version3(3) } | current | The data type TmnxIgmpVersion denotes the version of the IGMP protocol: - 'version1(1)': means version 1 of the IGMP protocol - 'version2(2)': means version 2 of the IGMP protocol - 'version3(3)': means version 3 of the… |
| TmnxIkePolicyAuthMethod | INTEGER { psk (1), hybridX509XAuth (2), plainX509XAuth (3), plainPskXAuth (4), cert (5) } | current | TmnxIkePolicyAuthMethod data type is an enumerated integer that describes the type of authentication method used. |
| TmnxIkePolicyOwnAuthMethod | INTEGER { symmetric (0), psk (1), cert (5) } | current | TmnxIkePolicyOwnAuthMethod data type is an enumerated integer that describes the type of authentication method used for its own side. |
| TmnxIngPolicerStatMode | INTEGER { noStats (0), minimal (1), offeredProfileNoCIR (2), offeredTotalCIR (3), offeredPrioNoCIR (4), offeredProfileCIR (5), offeredPrioCIR (6), offeredLimitedProfileCIR (7), offeredProfileCapCIR (8), offeredLimitedCapCIR (9) } | current | TmnxIngPolicerStatMode specifies the mode of statistics collected by this ingress policer. |
| TmnxIngPolicerStatModeOverride | INTEGER { noOverride (-1), noStats (0), minimal (1), offeredProfileNoCIR (2), offeredTotalCIR (3), offeredPrioNoCIR (4), offeredProfileCIR (5), offeredPrioCIR (6), offeredLimitedProfileCIR (7), offeredProfileCapCIR (8), offeredLimitedCapCIR (9) } | current | TmnxIngPolicerStatModeOverride specifies the override mode of statistics collected by this ingress policer. |
| TmnxIpSecIsaOperFlags | BITS { adminDown (0), noActive (1), noResources (2) } | current | The value of TmnxIpSecIsaOperFlags specifies the operational flags that determine the status of the MDAs associated with IPsec ISA. |
| TmnxIPsecTunnelTemplateId | Unsigned32 (1..2048) | current | A number used to identify an entry in the tIPsecTnlTempTable. |
| TmnxIPsecTunnelTemplateIdOrZero | Unsigned32 (0..2048) | current | A number used to identify an entry in the tIPsecTnlTempTable or zero. |
| TmnxLdpFECType | INTEGER { addrWildcard (1), addrPrefix (2), addrHost (3), vll (128), vpws (129), vpls (130) } | current | TmnxLdpFECType determines the kind of FEC that the label mapping, withdraw, release and request messages are referring to. |
| TmnxMacSpecification | DisplayString (SIZE (0..17)) | current | The data type TmnxMacSpecification is a string of ASCII characters that specifies how to format a string that represents a MAC address. The format is as follows: <mac-specification> ::= <alpha-string> [<delimiter-char>]… |
| TmnxManagedRouteStatus | INTEGER { installed (0), notYetInstalled (1), wrongAntiSpoofType (2), outOfMemory (3), shadowed (4), routeTableFull (5), parentInterfaceDown (6), hostInactive (7), enhancedSubMgmtRequired (8), deprecated1 (9), l2AwNotSupported (10) } | current | The data type TmnxManagedRouteStatus denotes the status of a Managed Route. |
| TmnxMdaQos | INTEGER { unknown (0), mda (1), hsmda1 (2), hsmda2 (3) } | current | TmnxMdaQos is an enumerated integer whose value specifies the Quality of Service support of a Media Dependent Adapter (MDA). |
| TmnxMldGroupFilterMode | INTEGER { include (1), exclude (2) } | current | The data type TmnxMldGroupFilterMode describes the filter-mode of a group. In 'include(1)' mode, reception of packets sent to the specified multicast address is requested only from those IPv6 source addresses listed in … |
| TmnxMldGroupType | INTEGER { static(1), dynamic(2) } | current | The data type TmnxMldGroupType describes how a multicast group is learned. |
| TmnxMldVersion | INTEGER { version1(1), version2(2) } | current | The data type TmnxMldVersion denotes the version of the MLD protocol: - 'version1(1)': means version 1 of the MLD protocol - 'version2(2)': means version 2 of the MLD protocol |
| TmnxMlpppEpClass | INTEGER { null (0), local (1), ipv4Address (2), macAddress (3), magicNumber (4), directoryNumber (5) } | current | The TmnxMlpppEpClass type represents the address class of the MLPPP Endpoint Discriminator option. |
| TmnxMobAccessType | INTEGER { eps (1), gprs (2), non3gpp (3) } | current | The data type TmnxMobAccessType describes the various access types. eps - evolved packet system. gprs - general packet radio services. non3gpp - trusted non-3gpp network such as evolved High Rate Packet Data (eHRPD) and… |
| TmnxMobAddrScheme | INTEGER { stateful (1), stateless (2) } | current | The data type TmnxMobAddrScheme describes the addressing scheme. If the value is set to 'stateful', User Equipment (UE) uses DHCPv6 to get IPv6 address. If the value is set to 'stateless', UE uses ICMPv6 to get IPv6 add… |
| TmnxMobApn | DisplayString (SIZE (1..80)) | current | The data type TmnxMobApn describes the Access Point Name (APN) associated with an User Equipment (UE). |
| TmnxMobApnOrZero | DisplayString (SIZE (0..80)) | current | The data type TmnxMobApnOrZero describes the Access Point Name (APN) associated with an User Equipment (UE). |
| TmnxMobArp | Unsigned32 (0..15) | current | The data type TmnxMobArp describes the QoS parameter, Allocation and Retention Priority (ARP). |
| TmnxMobArpValue | Unsigned32 (1..15) | current | The data type TmnxMobArpValue describes the Allocation and Retention Priority (ARP) value. |
| TmnxMobArpValueOrZero | Unsigned32 (0..15) | current | The data type TmnxMobArpValueOrZero describes the Allocation and Retention Priority (ARP) value. |
| TmnxMobAuthType | INTEGER { radius (1), diameter (2) } | current | The data type TmnxMobAuthType describes the authentication type used by mobile gateways. |
| TmnxMobAuthUserName | INTEGER { imsi (1), msisdn (2), pco (3) } | current | The data type TmnxMobAuthUserName describes the user name used in authentication requests by mobile gateways. |
| TmnxMobBearerId | Unsigned32 (1..15) | current | The data type TmnxMobBearerId describes the bearer identifier. |
| TmnxMobBearerType | INTEGER { default (1), dedicated (2) } | current | The data type TmnxMobBearerType describes the type of a bearer. |
| TmnxMobBufferLimit | Unsigned32 (1000..12000) | current | The data type TmnxMobBufferLimit describes the buffer limit in bytes. |
| TmnxMobChargingBearerType | INTEGER { home (1), visiting (2), roaming (3) } | current | The data type TmnxMobChargingBearerType describes the type of a bearer context used in charging applications. |
| TmnxMobChargingLevel | INTEGER { pdn (1), bearer (2) } | current | The data type TmnxMobChargingLevel describes the level where the charging is done. |
| TmnxMobChargingProfile | Unsigned32 (0..255) | current | The data type TmnxMobChargingProfile describes the charging trigger rules applied for generating Charging Data Records (CDR) for subscribers. |
| TmnxMobChargingProfileOrInherit | Integer32 (-1 | 0..255) | current | The data type TmnxMobChargingProfileOrInherit describes the charging trigger rules applied for generating Charging Data Records (CDR) for subscribers. A value of '-1' indicates that identifier will be inherited from ano… |
| TmnxMobDfPeerId | Unsigned32 (1..16) | current | The data type TmnxMobDfPeerId identifies Delivery Function (DF) peer for the mobile gateways. |
| TmnxMobDiaDetailPathMgmtState | INTEGER { error (0), idle (1), closed (2), localShutdown (3), remoteClosing (4), waitConnAck (5), waitCea (6), open (7), openCoolingDown (8), waitDns (9) } | current | The data type TmnxMobDiaDetailPathMgmtState describes the detail state of a path for a diameter connection. |
| TmnxMobDiaPathMgmtState | INTEGER { shutDown (0), shuttingDown (1), inactive (2), active (3) } | current | The data type TmnxMobDiaPathMgmtState describes the state of a path for a diameter connection. |
| TmnxMobDiaPeerHost | DisplayString (SIZE (0..80)) | current | The data type TmnxMobDiaPeerHost describes the name of a destination realm, originating realm and originating host. |
| TmnxMobDiaRetryCount | Unsigned32 (0..8) | current | The data type TmnxMobDiaRetryCount describes the diameter peer retry count value. |
| TmnxMobDiaTransTimer | Unsigned32 (1..180) | current | The data type TmnxMobDiaTransTimer describes the diameter peer transaction timer value in seconds. |
| TmnxMobDualStackPref | INTEGER { ipv4 (1), ipv6 (2), useCplane (3) } | current | The data type TmnxMobDualStackPref describes the preference in a dual IP stack. The value 'useCplane' specifies that the value is inherited from the preference in a dual IP stack on control plane. |
| TmnxMobGwId | Unsigned32 (1..8) | current | The data type TmnxMobGwId identifies mobile gateways. |
| TmnxMobGwType | INTEGER { sgw (1), pgw (2), wlanGw (3) } | current | The data type TmnxMobGwType describes the mobile gateway type. |
| TmnxMobImei | DisplayString (SIZE (0|16)) | current | The data type TmnxMobImei describes the International Mobile Equipment Identity (IMEI) of an User Equipment (UE). |
| TmnxMobImsi | OCTET STRING (SIZE (8)) | current | The data type TmnxMobImsi describes the International Mobile Subscriber Identity (IMSI) of an User Equipment (UE). IMSI is defined as a number consisting of up to 15 BCD digits. The first 3 digits are the Mobile Country… |
| TmnxMobImsiStr | DisplayString (SIZE (0|9..15)) | current | The data type TmnxMobImsiStr describes the International Mobile Subscriber Identity (IMSI) of a User Equipment (UE). |
| TmnxMobIpCanType | INTEGER { epc3gpp (1), gprs3gpp (2) } | current | The data type TmnxMobIpCanType describes the type of Internet Protocol Connectivity Access Network (IP-CAN) session as Evolved Packet Core (epc3gpp) or GPRS (gprs3gpp). |
| TmnxMobLiTarget | OCTET STRING (SIZE (8)) | current | The data type TmnxMobLiTarget describes the target for the interception. The target can be of type International Mobile Subscriber Identity (IMSI), Mobile Subscriber Integrated Services Digital Network (MSISDN) or Inter… |
| TmnxMobLiTargetType | INTEGER { imsi (1), msisdn (2), imei (3) } | current | The data type TmnxMobLiTargetType describes the types of target in Lawful Interception (LI). |
| TmnxMobMcc | DisplayString (SIZE (3)) | current | The data type TmnxMobMcc describes the Mobile Country Code (MCC) of an User Equipment (UE). |
| TmnxMobMccOrEmpty | DisplayString (SIZE (0|3)) | current | The data type TmnxMobMccOrEmpty describes the Mobile Country Code (MCC) of an User Equipment (UE). |
| TmnxMobMnc | DisplayString (SIZE (2|3)) | current | The data type TmnxMobMnc describes the Mobile Network Code (MNC) of an User Equipment (UE). |
| TmnxMobMncOrEmpty | DisplayString (SIZE (0|2|3)) | current | The data type TmnxMobMncOrEmpty describes the Mobile Network Code (MNC) of an User Equipment (UE). |
| TmnxMobMsisdn | DisplayString (SIZE (0..15)) | current | The data type TmnxMobMsisdn describes the Mobile Subscriber Integrated Services Digital Network (MSISDN) number of an User Equipment (UE). |
| TmnxMobNai | DisplayString (SIZE (0..72)) | current | The data type TmnxMobNai describes the Network Address Identifier (NAI) of an User Equipment (UE). |
| TmnxMobNode | DisplayString (SIZE (0..30)) | current | The data type TmnxMobNode describes the name of a mobile gateway which consists of Mobile Country Code (MCC), Mobile Network Code (MNC), Region string, Group Id, Node Id. A mobile gateway name can be described as follow… |
| TmnxMobPathMgmtState | INTEGER { disabled (0), up (1), reqTimeOut (2), fault (3), idle (4), restart (5) } | current | The data type TmnxMobPathMgmtState describes the state of a path for a reference point. A value of 'reqTimeOut' indicates that the peer is not replying to the Echo Request messages the SGW is sending out. |
| TmnxMobPdnGyChrgTriggerType | INTEGER { sgsnIpAddrRecvd (0), qosRecvd (1), locRecvd (2), ratRecvd (3), qosTrfClsRecvd (4), qosRlbClsRecvd (5), qosDlyClsRecvd (6), qosPeakThrptRecvd (7), qosPrcClsRecvd (8), qosMeanTrptRecvd (9), qosMxBtRtUplnkRecvd (10), qosMxBtRtDllnkRecvd (11), qosResBerRecvd (12), qosSduErrRatRecvd (13), qosTransDelayRecvd (14), qosTrfHndPriRecvd (15), qosGrtBtRtUplnkRecvd (16), qosGrtBtRtDllnkRecvd (17), locMccRecvd (18), locMncRecvd (19), locRacRecvd (20), locLacRecvd (21), locCellIdRecvd (22), medCompRecvd (23), partcNmbRecvd (24), thrldPartcNmbRecvd (25), usrPartcTypeRecvd (26), servCondRecvd (27), servNodeRecvd (28), usrCsgInfoRecvd (29) } | current | The data type TmnxMobPdnGyChrgTriggerType describes type of the trigger activated by the Online Charging System (OCS). sgsnIpAddrRecvd - Change in Serving GPRS Support Node (SGSN) IP address qosRecvd - Change in Quality… |
| TmnxMobPdnRefPointType | INTEGER { s5 (1), s8 (2), gn (3), s2a (4), gp (5) } | current | The data type TmnxMobPdnRefPointType describes the types of reference point. |
| TmnxMobPdnSessionEvent | INTEGER { sessionInvalid (0), gtpCreateSessReq (1), gtpUpdateBearerReq (2), gtpDeleteSessReq (3), gtpDeleteBearerResp (4), gtpUpdateBearerResp (5), gtpModifyActiveToIdle (6), gtpResrcAllocCmd (7), gtpModifyQosCmd (8), gtpX1eNodeBTeidUpdate (9), gtpX2SrcSgwDeleteSessReq (10), gtpS1CreateIndirectTunnel (11), dlPktRecvIndication (12), dlPktNotificationAck (13), dlPktNotificationFail (14), pcrfSessEstResp (15), pcrfSessTerminateRsp (16), pcrfProvQosRules (17), pmipSessResp (18), pmipSessUpdate (19), pmipSessDeleteRsp (20), pmipSessDeleteReq (21), eventMax (22) } | current | The data type TmnxMobPdnSessionEvent describes the feedback signaling message (FSM) event of a Packet Data Network (PDN) session. |
| TmnxMobPdnSessionState | INTEGER { invalid (0), init (1), waitPcrfResponse (2), waitPgwResponse (3), waitEnodebUpdate (4), connected (5), ulDelPending (6), dlDelPending (7), idleMode (8), pageMode (9), dlHandover (10), incomingHandover (11), outgoingHandover (12), stateMax (13) } | current | The data type TmnxMobPdnSessionState describes the feedback signaling message (FSM) state of a Packet Data Network (PDN) session. |
| TmnxMobPdnType | INTEGER { ipv4 (1), ipv6 (2), ipv4v6 (3) } | current | The data type TmnxMobPdnType describes the type of a Pakcet Data Network (PDN). |
| TmnxMobPeerType | INTEGER { sgw (1), pgw (2), hsgw (3) } | current | The data type TmnxMobPeerType describes the type of the mobile gateway peer as Serving Gateway (SGW), Packet Data Network Gateway (PGW) or High Rate Packet Data (HRPD) Serving Gateway (HSGW). |
| TmnxMobPgwSigProtocol | INTEGER { gtp (1), pmip (2) } | current | The data type TmnxMobPgwSigProtocol describes the signaling protocol used on S5 or S8 reference point. |
| TmnxMobPresenceState | INTEGER { absent (0), present (1) } | current | The data type TmnxMobPresenceState describes the whether the given field is present. |
| TmnxMobProfGbrRate | Unsigned32 (0..100000) | current | The data type TmnxMobProfGbrRate describes the Guaranteed Bit Rate (GBR) value in kilo-bits per second(kbps). |
| TmnxMobProfIpTtl | Unsigned32 (1..255) | current | The data type TmnxMobProfIpTtl describes the Time-To-Live (TTL) value. |
| TmnxMobProfMbrRate | Unsigned32 (0..100000) | current | The data type TmnxMobProfMbrRate describes the Maximum Bit Rate (MBR) value in kilo-bits per second(kbps). |
| TmnxMobProfName | TNamedItem | current | The data type TmnxMobProfName describes the name of a profile used by mobile gateways. |
| TmnxMobProfNameOrEmpty | TNamedItemOrEmpty | current | The data type TmnxMobProfNameOrEmpty describes the name of a profile used by mobile gateways. |
| TmnxMobProfPolChargingMethod | INTEGER { profChargingMtd (0), online (1), offline (2), both (3) } | current | TmnxMobProfPolChargingMethod data type is an enumerated integer that describes the Charging Method for the Policy and Charging Control (PCC) rule. A variable of this type could be set to 'online' charging method, 'offli… |
| TmnxMobProfPolMeteringMethod | INTEGER { timeBased (1), volBased (2), both (3) } | current | TmnxMobProfPolMeteringMethod data type is an enumerated integer that describes the Metering Method for the Policy and Charging Control (PCC) rule. |
| TmnxMobProfPolReportingLevel | INTEGER { servId (1), ratingGrp (2) } | current | TmnxMobProfPolReportingLevel data type is an enumerated integer that describes the Reporting level for the Policy and Charging Control (PCC) rule. |
| TmnxMobQci | Unsigned32 (0..9) | current | The data type TmnxMobQci describes the QoS Class Identifier. |
| TmnxMobQciValue | Unsigned32 (1..9) | current | The data type TmnxMobQciValue describes the QoS Class Identifier (QCI) value. |
| TmnxMobQciValueOrZero | Unsigned32 (0..9) | current | The data type TmnxMobQciValueOrZero describes the QoS Class Identifier (QCI) value. |
| TmnxMobQueueLimit | Unsigned32 (1000..12000) | current | The data type TmnxMobQueueLimit describes the queue limit in bytes. |
| TmnxMobRatingGrpState | INTEGER { allowFlow (1), disallowFlow (2), redWebPortal (3), allowResRules (4), iom1stPktTrigger (5), dis1stPktTrigger (6), creditsToppedUp (7), waitForFpt (8) } | current | The data type TmnxMobRatingGrpState describes the state of a rating group. allowFlow - Allow the traffic to flow disallowFlow - Disallow the traffic to Flow redWebPortal - Redirect the traffic to web portal allowResRule… |
| TmnxMobRfAcctLevel | INTEGER { pdnLevel (1), qciLevel (2) } | current | TmnxMobRfAcctLevel data type is an enumerated integer that describes the accounting level. |
| TmnxMobRtrAdvtInterval | Unsigned32 (1..60) | current | The data type TmnxMobRtrAdvtInterval describes the router advertisement interval in minutes. |
| TmnxMobRtrAdvtLifeTime | Unsigned32 (1..24) | current | The data type TmnxMobRtrAdvtLifeTime describes the router advertisement life time in hours. |
| TmnxMobSdf | Unsigned32 (0..255) | current | The data type TmnxMobSdf describes the number of Service Data Flows (SDFs). |
| TmnxMobSdfFilter | Unsigned32 (0..16) | current | The data type TmnxMobSdfFilter describes a IP filter in a Service Data Flow (SDF) or Traffic Flow Template (TFT). |
| TmnxMobSdfFilterDirection | INTEGER { preRel7 (0), downLink (1), upLink (2), biDir (3) } | current | The data type TmnxMobSdfFilterDirection describes the direction on which a Service Data Flow (SDF) filter rule is valid. |
| TmnxMobSdfFilterNum | Unsigned32 (0..16) | current | The data type TmnxMobSdfFilterNum describes the number of IP filters. |
| TmnxMobSdfFilterProtocol | INTEGER { any (-1), ipv6HopByOpOpt (0), icmp (1), igmp (2), ggp (3), ip (4), st (5), tcp (6), cbt (7), egp (8), igp (9), bbnRccMon (10), nvp2 (11), pup (12), argus (13), emcon (14), xnet (15), chaos (16), udp (17), mux (18), dcnMeas (19), hmp (20), prm (21), xnsIdp (22), trunk1 (23), trunk2 (24), leaf1 (25), leaf2 (26), rdp (27), irdp (28), isoTp4 (29), netblt (30), mfeNsp (31), meritInp (32), dccp (33), pc3 (34), idpr (35), xtp (36), ddp (37), idprCmtp (38), tpplusplus (39), il (40), ipv6 (41), sdrp (42), ipv6Route (43), ipv6Frag (44), idrp (45), rsvp (46), gre (47), dsr (48), bna (49), esp (50), ah (51), iNlsp (52), swipe (53), narp (54), mobile (55), tlsp (56), skip (57), ipv6Icmp (58), ipv6NoNxt (59), ipv6Opts (60), anyHostIntl (61), cftp (62), anyLocalNet (63), satExpak (64), kryptolan (65), rvd (66), ippc (67), anyDFS (68), satMon (69), visa (70), ipcv (71), cpnx (72), cphb (73), wsn (74), pvp (75), brSatMon (76), sunNd (77), wbMon (78), wbExpak (79), isoIp (80), vmtp (81), secureVmpt (82), vines (83), ttp (84), nsfnetIgp (85), dgp (86), tcf (87), eiGrp (88), ospfIgp (89), spriteRpc (90), larp (91), mtp (92), ax25 (93), ipip (94), micp (95), sccSp (96), etherIp (97), encap (98), anyPEC (99), gmtp (100), ifmp (101), pnni (102), pim (103), aris (104), scps (105), qnx (106), activeNet (107), ipComp (108), snp (109), compaqPeer (110), ipxInIp (111), vrrp (112), pgm (113), any0hop (114), l2tp (115), ddx (116), iatp (117), stp (118), srp (119), uti (120), smp (121), sm (122), ptp (123), isis (124), fire (125), crtp (126), crudp (127), sscopmce (128), iplt (129), sps (130), pipe (131), sctp (132), fc (133), rsvpE2eIgnore (134), mobHeader (135), udpLite (136), mplsInIp (137), manet (138), hip (139), shim6 (140) } | current | The data type TmnxMobSdfFilterProtocol describes IPv4 protocol or IPv6 next header on which Service Data Flow (SDF) filter matches. |
| TmnxMobSdfRuleName | DisplayString (SIZE (1..64)) | current | The data type TmnxMobSdfRuleName describes the policy rule name of a Service Data Flow (SDF). |
| TmnxMobServerState | INTEGER { na (0), up (1), down (2) } | current | The data type TmnxMobServerState describes the state of a server connected with a mobile gateway. |
| TmnxMobServRefPointType | INTEGER { s5 (1), s8 (2), s2a (4) } | current | The data type TmnxMobServRefPointType describes the types of reference point. |
| TmnxMobStaticPolPrecedence | Unsigned32 (1..65536) | current | The data type TmnxMobStaticPolPrecedence describes the precedence value for a static policy configured in the system. |
| TmnxMobStaticPolPrecedenceOrZero | Unsigned32 (0..65535) | current | The data type TmnxMobStaticPolPrecedence describes the precedence value for a static policy configured in the system. |
| TmnxMobUeId | OCTET STRING (SIZE (8)) | current | The data type TmnxMobUeId describes the identity of an User Equipment. TmnxMobUeId can be of the following types: International Mobile Subscriber Identity (IMSI), International Mobile station Equipment Identity (IMEI), … |
| TmnxMobUeIdType | INTEGER { imsi (0), imei (1), msisdn (2) } | current | The data type TmnxMobUeIdType describes the types of identification for User Equipment (UE). |
| TmnxMobUeRat | INTEGER { utran (1), geran (2), wlan (3), gan (4), hspa (5), eutran (6), ehrpd (7), hrpd (8), oneXrtt (9), umb (10) } | current | The data type TmnxMobUeRat describes the Radio Access Type (RAT) of an User Equipment (UE). |
| TmnxMobUeState | INTEGER { idle (1), active (2), paging (3), init (4), suspend (5), ddnDamp (6) } | current | The data type TmnxMobUeState describes the state of an User Equipment (UE). |
| TmnxMobUeStrPrefix | DisplayString (SIZE (4..15)) | current | The data type TmnxMobUeStrPrefix describes the prefix for International Mobile Subscriber Identity (IMSI) or Mobile Subscriber Integrated Services Digital Network (MSISDN) of an User Equipment (UE). |
| TmnxMobUeSubType | INTEGER { homer (1), roamer (2), visitor (3) } | current | The data type TmnxMobUeSubType describes the subscription type of User Equipment (UE). |
| TmnxMplsTpGlobalID | Unsigned32 | current | The value of TmnxMplsTpGlobalID specifies the MPLS-TP global identifier. |
| TmnxMplsTpNodeID | Unsigned32 | current | The value of TmnxMplsTpNodeID specifies the MPLS-TP node identifier. |
| TmnxMplsTpTunnelType | INTEGER { mplsTpStatic (1) } | current | The type of this MPLS-TP tunnel entity. |
| TmnxMsPwPeSignaling | INTEGER { auto (1), master (2) } | current | A number used to identify a multi-segment pseudo-wire provider-edge signaling type. |
| TmnxMulticastAddrFamily | INTEGER { ipv4Multicast (0), ipv6Multicast (1) } | current | The data type TmnxMulticastAddrFamily denotes the family for multicast protocol. |
| TmnxOperGrpHoldDownTime | Unsigned32 (0..3600) | current | TmnxOperGrpHoldDownTime indicates time-interval in seconds for the service operational-group hold down time. |
| TmnxOperGrpHoldUpTime | Unsigned32 (0..3600) | current | TmnxOperGrpHoldUpTime indicates time-interval in seconds for the service operational-group hold uptime. |
| TmnxOperState | INTEGER { unknown (1), inService (2), outOfService (3), transition (4) } | current | The TmnxOperState data type is an enumerated integer that describes the values used to identify the current operational state of functional modules. |
| TmnxOspfInstance | Unsigned32 (0..31) | current | A number used to identify an instance of OSPF. |
| TmnxPortID | InterfaceIndex | current | On PSS, the TmnxPortID will be the ifIndex as encoded in PSS. Port Identifier: 32 .. 25|24 .. 17|16 .. 9|8 .. 1 + | shelf(8) | slot(8) |0| port(7)| unused(8)| + WANIF Identifier: 32 .. 25|24 .. 17|16 .. 9|8 .. 1 + | she… |
| TmnxPppNcpProtocol | INTEGER { ipcp (1), ipv6cp (2) } | current | The TmnxPppNcpProtocol data type represents the PPP Network Control Protocol. |
| TmnxPppoePadoDelay | Unsigned32 (0|1..30) | current | The data type TmnxPppoePadoDelay specifies the delay timeout in deci-seconds before sending a PADO (PPPoE Active Discovery Offer). |
| TmnxPppoeSessionId | Unsigned32 (0..65535) | current | The TmnxPppoeSessionId indicates the 16 bit wide PPPoE session Id. |
| TmnxPppoeSessionInfoOrigin | INTEGER { none (0), default (1), radius (2), localUserDb (3), dhcp (4), midSessionChange (5), tags (6), l2tp (7) } | current | The TmnxPppoeSessionInfoOrigin indicates the originator of the provided information. |
| TmnxPppoeSessionType | INTEGER { local (1), localWholesale (2), localRetail (3), l2tp (4) } | current | The TmnxPppoeSessionType indicates the type of PPPoE session. |
| TmnxPppoeUserName | DisplayString (SIZE (1..128)) | current | The data type TmnxPppoeUserName denotes the PPPoE username. |
| TmnxPppoeUserNameOrEmpty | DisplayString (SIZE (0..128)) | current | The data type TmnxPppoeUserNameOrEmpty denotes the PPPoE username. |
| TmnxPwGlobalId | Unsigned32 (1..4294967295) | current | A number used to identify a global pseudo-wire routing identifier. |
| TmnxPwGlobalIdOrZero | Unsigned32 | current | A number used to identify a global pseudo-wire routing identifier or zero. |
| TmnxPwPathHopId | Unsigned32 (1..16) | current | A number used to identify a specific hop associated with pseudo-wire routing path. |
| TmnxPwPathHopIdOrZero | Unsigned32 (0..16) | current | A number used to identify a specific hop associated with pseudo-wire routing path. |
| TmnxQosBytesHex | OCTET STRING (SIZE (0..30)) | current | Represents the QoS bytes that has been requested for the bearer context of an User Equipment (UE). |
| TmnxRadiusPendingReqLimit | Unsigned32 (1..4096) | current | The TmnxRadiusPendingReqLimit data type is a number that specifies the limit to the number of pending RADIUS request messages. |
| TmnxRadiusServerOperState | INTEGER { unknown (1), inService (2), outOfService (3), transition (4), overloaded (5) } | current | The TmnxRadiusServerOperState data type is an enumerated integer that describes the values used to identify the operational state of a RADIUS server. |
| TmnxReasContextVal | Unsigned32 (0..31) | current | The value of the label used to identify the entity using the specified context value on a specific port. 31 0 + |00000000 00000000 00000000 000XXXXX| + The value of this object is encoded in the least significant 5 bits… |
| TmnxRsvpDSTEClassType | Unsigned32 (0..7) | current | TmnxRsvpDSTEClassType is an unsigned integer in the range of (0..7) that defines the class type (CT). |
| TmnxServId | Unsigned32 (0|1..2147483647|2147483648|2147483649|2147483650) | current | A number used to identify a Service. This ID must be unique within the Service Domain. The value 0 is used as the null ID. |
| TmnxSlaProfileString | DisplayString (SIZE (1..16)) | current | The data type TmnxSlaProfileString denotes the SLA profile string. |
| TmnxSlaProfileStringOrEmpty | DisplayString (SIZE (0..16)) | current | The data type TmnxSlaProfileStringOrEmpty denotes the SLA profile string. The empty string denotes the absence of a SLA profile. |
| TmnxSlopeMap | INTEGER { none (0), low (1), high (2), highLow (3) } | current | TmnxSlopeMap indicates the mapping style of the slope. |
| TmnxSpbBridgePriority | Integer32 (0..15) | current | TmnxSpbFid indicates the bridge priority for Shortest Path Bridging. |
| TmnxSpbFdbLocale | INTEGER { local (1), sap (2), sdp (3), unknown (4) } | current | TmnxSpbFdbLocale data type is an enumerated integer that describes the values used to indicate source of forwarding data-base (FDB) entry for Shortest Path Bridging (SPB). |
| TmnxSpbFdbState | INTEGER { ok (0), addModPending (1), delPending (2), sysFdbLimit (3), noFateShared (4), svcFdbLimit (5), noUcast (6) } | current | TmnxSpbFdbState data type is an enumerated integer that describes the values used to indicate state of the forwarding data-base FDB entry for Shortest Path Bridging (SPB). |
| TmnxSpbFid | Integer32 (1..4095) | current | TmnxSpbFid indicates Shortest Path Bridging forwarding database identifier. |
| TmnxSpbFidOrZero | Integer32 (0..4095) | current | TmnxSpbFid indicates Shortest Path Bridging forwarding database identifier. |
| TmnxSpokeSdpId | Unsigned32 (1..4294967295) | current | A number used to identify a multi-segment pseudo-wire provider-edge identifier. |
| TmnxSpokeSdpIdOrZero | Unsigned32 | current | A number used to identify a multi-segment pseudo-wire provider-edge identifier. |
| TmnxSrrpPriorityStep | Integer32 (0..10) | current | TmnxSrrpPriorityStep indicates the range of the priority steps used by the operational group to monitor SRRP. |
| TmnxStatus | INTEGER { create (1), delete (2) } | current | The TmnxStatus data type is an enumerated integer that describes the values used to identify the current status of functional modules in the system such as OSPF and MPLS protocols. Setting this variable to 'create' caus… |
| TmnxStrSapId | DisplayString (SIZE (0..32)) | current | The value of TmnxStrSapId is a printable string which contains the owner SAP Id or equivalent on a remote system. The string should contain the printable string equivalent of the textual-conventions TmnxPortID and TmnxE… |
| TmnxSubAleOffset | INTEGER { none (0), pppoaLlc (1), pppoaNull (2), pppoeoaLlc (3), pppoeoaLlcFcs (4), pppoeoaLlcTagged (5), pppoeoaLlcTaggedFcs (6), pppoeoaNull (7), pppoeoaNullFcs (8), pppoeoaNullTagged (9), pppoeoaNullTaggedFcs (10), ipoaLlc (11), ipoaNull (12), ipoeoaLlc (13), ipoeoaLlcFcs (14), ipoeoaLlcTagged (15), ipoeoaLlcTaggedFcs (16), ipoeoaNull (17), ipoeoaNullFcs (18), ipoeoaNullTagged (19), ipoeoaNullTaggedFcs (20), pppoe (21), pppoeTagged (22), ipoe (23), ipoeTagged (24) } | current | The data type TmnxSubAleOffset specifies the encapsulation offset value of the subscriber in the DSL access loop as used by the 7xxx system. This offset is used in 7xxx egress shaping in order to accurately shape the en… |
| TmnxSubAleOffsetMode | INTEGER { none (0), auto (1) } | current | The data type TmnxSubAleOffsetMode specifies the way the encapsulation offset of the subscriber in the DSL access loop is learned by the 7xxx system. This offset is used in 7xxx egress shaping, adjusting the subscriber … |
| TmnxSubIdentString | DisplayString (SIZE (1..32)) | current | The data type TmnxSubIdentString denotes the subscriber identification string. |
| TmnxSubIdentStringOrEmpty | DisplayString (SIZE (0..32)) | current | The data type TmnxSubIdentStringOrEmpty denotes the subscriber identification string. The empty string denotes the absence of a subscriber identification string. |
| TmnxSubMgtIntDestId | TmnxSubMgtIntDestIdOrEmpty (SIZE (1..32)) | current | The data type TmnxSubMgtIntDestId denotes the intermediate destination id. |
| TmnxSubMgtIntDestIdOrEmpty | DisplayString (SIZE (0..32)) | current | The data type TmnxSubMgtIntDestIdOrEmpty denotes the intermediate destination id. The empty string denotes the absence of an intermediate destination id. |
| TmnxSubMgtOrgString | TmnxSubMgtOrgStrOrZero (SIZE (1..32)) | current | The data type TmnxSubMgtOrgStrOrZero denotes the organization string. |
| TmnxSubMgtOrgStrOrZero | DisplayString (SIZE (0..32)) | current | The data type TmnxSubMgtOrgStrOrZero denotes the organization string. The empty string denotes the absence of an organization string. |
| TmnxSubNasPortPrefixType | INTEGER { none (0), userString (1) } | current | The TmnxSubNasPortPrefixType data type is an enumerated integer that specifies what prefix will be added to the RADIUS NAS-Port attribute: - none (0): No prefix will be added. - userString (1): A user configurable strin… |
| TmnxSubNasPortSuffixType | INTEGER { none (0), circuitId (1), remoteId (2) } | current | The TmnxSubNasPortSuffixType data type is an enumerated integer that specifies what suffix will be added to the RADIUS NAS-Port attribute: - none (0): No suffix will be added. - circuitId (1): If available, the circuit-… |
| TmnxSubNasPortTypeType | INTEGER { standard (1), config (2) } | current | The TmnxSubNasPortTypeType data type is an enumerated integer that specifies what value will be put in the RADIUS NAS-Port-Type attribute: - standard (1): according to the RADIUS specification RFC 2865 section 5.41 NAS-… |
| TmnxSubProfileString | DisplayString (SIZE (1..16)) | current | The data type TmnxSubProfileString denotes the subscriber profile string. |
| TmnxSubProfileStringOrEmpty | DisplayString (SIZE (0..16)) | current | The data type TmnxSubProfileStringOrEmpty denotes the subscriber profile string. The empty string denotes the absence of a subscriber profile. |
| TmnxSubRadiusAttrType | Unsigned32 (0..255) | current | The TmnxSubRadiusAttrType data type contains a number that indicates a RADIUS attribute type. |
| TmnxSubRadiusVendorId | Unsigned32 (0..16777215) | current | The TmnxSubRadiusVendorId data type contains a number that indicates a RADIUS Vendor-Id. |
| TmnxSubRadServAlgorithm | INTEGER { direct (1), roundRobin (2), hashBased (3) } | current | The TmnxSubRadServAlgorithm data type is an enumerated integer that indicates the algorithm used to access the list of configured RADIUS servers: - direct (1): The first server will be used as primary server for all req… |
| TmnxSvcOperGrpCreationOrigin | INTEGER { manual (1), mvrp (2) } | current | A number used to identify creation origin for the service operational group. |
| TmnxThresholdGroupType | INTEGER { brMgmtLimit (1), brMgmtCfSuccess (2), brMgmtCfFailure (3), brMgmtTraffic (4), pathMgmt (5), cpmSystem (6), mgIsmSystem (7) } | current | The TmnxThresholdGroupType is an enumerated integer that describes the group type in threshold based monitoring. brMgmtLimit - indicates the group for bearer management limit brMgmtCfSuccess - indicates the group for be… |
| TmnxTimeInSec | Unsigned32 (0..86400) | current | The data type TmnxTimeInSec describes the Tarrif Time for the Charging Data Record (CDR). |
| TmnxTlsGroupId | Unsigned32 (1..4094) | current | A number used to identify a TLS Group. This ID must be unique within that Service Domain. |
| TmnxTunnelGroupId | Unsigned32 (1..16) | current | The value of TmnxTunnelGroupId specifies the tunnel-group identifier. |
| TmnxTunnelGroupIdOrZero | Unsigned32 (0..16) | current | The value of TmnxTunnelGroupId specifies the tunnel-group identifier including zero indicating that group-id is not specified. |
| TmnxTunnelID | Unsigned32 | current | The identifying value for a BGP-VPRN tunnel. Depending on the tunnel type the associated tunnel-id may be an sdp-id, an lsp-id or zero(0). |
| TmnxTunnelType | INTEGER { sdp (1), ldp (2), rsvp (3), gre (4), bypass (5), invalid (6), bgp (7) } | current | The type of this tunnel entity. |
| TmnxVcId | Unsigned32 (1..4294967295) | current | A 32 bit number is used to identify a VC(Virtual Circuit). The VC ID cannot be 0. |
| TmnxVcIdOrNone | Unsigned32 (0|1..4294967295) | current | A 32 bit number is used to identify a VC(Virtual Circuit). A value of 0 indicates no VC ID is configured or available. |
| TmnxVcType | INTEGER { frDlciMartini(1), atmSdu(2), atmCell(3), ethernetVlan(4), ethernet(5), atmVccCell(9), atmVpcCell(10), ipipe(11), satopE1(17), satopT1(18), satopE3(19), satopT3(20), cesopsn(21), cesopsnCas(23), frDlci(25), mirrorDest(4096) } | current | The value of TmnxVcType is an enumerated integer that indicates a Virtual Circuit (VC) type. 'frDlciMartini(1)' replaces the old 'frDlci' when used over martini tunnels. |
| TmnxVdoAnalyzerAlarm | INTEGER { none (0), tnc (1), qos (2), poa (3) } | current | The data type TmnxVdoAnalyzerAlarm is an enumerated integer that specifies the severity of the analyzer state alarm. Setting a variable of this type to 'none' indicates no error level. A value of 'tnc' indicates a TNC (… |
| TmnxVdoAnalyzerAlarmStates | OCTET STRING (SIZE (10)) | current | |
| TmnxVdoFccServerMode | INTEGER { none (0), burst (1), dent (2), hybrid (3) } | current | The TmnxVdoFccServerMode data type is an enumerated integer that describes the mode of the Fast Channel Change (FCC) server. A value of 'burst' indicates that the FCC server is enabled and will send the channel at a nom… |
| TmnxVdoGrpId | Unsigned32 (0..4) | current | TmnxVdoGrpId data type describes the identifier for a video group. |
| TmnxVdoGrpIdIndex | Unsigned32 (1..4) | current | TmnxVdoGrpIdIndex data type describes the id of a TIMETRA-VIDEO-MIB::tmnxVdoGrpEntry and is the primary index for the table. |
| TmnxVdoGrpIdOrInherit | Integer32 (-1|0..4) | current | The data type describes the identifier for a video group. A value of '-1' indicates that identifier will be inherited from another object that is usually in another mib table. |
| TmnxVdoIfName | TNamedItem | current | The data type describes the name of a video interface. The name of a video interface must always start with a letter. |
| TmnxVdoOutputFormat | INTEGER { udp (1), rtp-udp (2) } | current | The data type TmnxVdoOutputFormat is an enumerated integer that specifies the output format of the video stream. Setting a variable of this type to 'udp' causes the video stream to be of type 'udp' whereas setting a val… |
| TmnxVdoPortNumber | Unsigned32 (1024..5999 | 6251..65535) | current | The data type describes the port number of an Internet transport layer protocol. |
| TmnxVdoStatInt | INTEGER { current (1), interval (2) } | current | The data type TmnxVdoStatInt is an enumerated integer that specifies the time duration for which the video statistics are being counted. Setting a variable of this type to 'current' causes the time duration to be set to… |
| TmnxVpnIpBackupFamily | BITS { ipv4 (0), ipv6 (1) } | current | The value of TmnxVpnIpBackupFamily specifies the respective vpn family for which backup paths would be enabled. |
| TmnxVPNRouteDistinguisher | OCTET STRING (SIZE (8)) | current | The VPRN route distinguisher is a 8-octet object. It contains a 2-octet type field followed by a 6-octet value field. The type field specify how to interpret the value field. Type 0 specifies two subfields as a 2-octet … |
| TmnxVRtrID | Integer32 (1..10240) | current | A number used to identify a virtual router instance in the system. |
| TmnxVRtrIDOrZero | Integer32 (0..10240) | current | A number used to identify a virtual router instance in the system. The number 0 will have special significance in the context the TC is used. |
| TmnxVRtrMplsLspID | Unsigned32 (0..65535) | current | A unique value, greater than zero, for each Label Switched Path in the managed system. |
| TmnxVwmCardType | INTEGER { not-provisioned (0), not-equipped (1), sfc1A (2), sfc1B (3), sfc1C (4), sfc1D (5), sfc1E (6), sfc1F (7), sfc1G (8), sfc1H (9), sfc2AandB (10), sfc2CandD (11), sfc2EandF (12), sfc2GandH (13), sfc4A-D (14), sfc4E-H (15), sfc8 (16), sfd8A-R (17), sfd8B-R (18), sfd8C-R (19), sfd8D-R (20), sfd4A-R (21), sfd4B-R (22), sfd4C-R (23), sfd4D-R (24), sfd4E-R (25), sfd4F-R (26), sfd4G-R (27), sfd4H-R (28), sfd2A-R (29), sfd2B-R (30), sfd2C-R (31), sfd2D-R (32), sfd2E-R (33), sfd2F-R (34), sfd2G-R (35), sfd2H-R (36), sfd2I-R (37), sfd2L-R (38), sfd2M-R (39), sfd2N-R (40), sfd2O-R (41), sfd2P-R (42), sfd2Q-R (43), sfd2R-R (44) } | current | The TmnxVwmCardType data type is an enumerated integer that describes the values used to identify the VWM Shelf Card type. |
| TMplsLspExpProfMapID | TPolicyID (1..65535) | current | The identification number of a MPLS LSP EXP profile. |
| TNamedItem | DisplayString (SIZE (1..32)) | current | The name of an item. When used as an index to a table, the item name uniquely identifies the instance. When used in a reference (TNamedItemOrEmpty) the item name entry must exist in the table. Note, use only NVT ASCII d… |
| TNamedItemOrEmpty | DisplayString (SIZE (0 | 1..32)) | current | The name of an item, or an empty string. When used in a reference (TNamedItemOrEmpty) the item name entry must exist in the table. Note, use only NVT ASCII displayable characters here, no control characters, no UTF-8, e… |
| TNetworkIngressMeterId | Integer32 (0 | 1..16) | current | Ingress Meter Id |
| TNetworkPolicyID | TPolicyID (1..65535|65536|65537) | current | the identification number of a network policy. |
| TNonZeroWeight | Integer32 (1..100) | current | The weight of the specified entity while feeding into the parent. |
| TnSwitchID | Integer32 | current | A Switch ID that can be used to uniquely identify a switching domain on an NE. 32 29 | 28 23 | 22 17 | 16 1 | + |type=1| shelf | slot | unused| + type=1 : binary 0001 = shelf/slot config. 32 29 | 28 23 | 22 17 | 16 1 | … |
| TOperator | INTEGER { none(0), eq(1), range(2), lt(3), gt(4) } | current | The operator specifies the manner in which a couple of other MIB objects in the table are supposed to be used. Operator Value1 Value2 none(0) Any(0) Any(0) eq(1) Specified Value Any(0) range(2) Starting Value Ending Val… |
| TPerPacketOffset | Integer32 (-32..31) | current | The value, in bytes, of the adjustment to make to the size of each packet for accounting. |
| TPerPacketOffsetOvr | Integer32 (-128 | -32..31) | current | The value, in bytes, of the override of the adjustment to make to the size of each packet for accounting. A value of -128 indicates no override. |
| TPIRPercentOverride | Integer32 (-2 | 1..10000) | current | The PIR percentage rate specified in hundredths of a percent. A value of -2 specifies no override. |
| TPIRRate | Integer32 (-1 | 1..100000000) | current | The PIR rate to be used in kbps. The value -1 means maximum rate. |
| TPIRRateOrZero | Integer32 (-1 | 0..100000000) | current | The PIR rate to be used in kbps. The value -1 means maximum rate. The value 0 means undefined rate. |
| TPIRRateOverride | Integer32 (-2 | -1 | 1..100000000) | current | The PIR rate to be used in kbps. The value -1 means maximum rate. A value of -2 specifies no override. |
| TPIRRatePercent | Integer32 (1..100) | current | The percentage of maximum PIR rate allowed. A value of 0 is not acceptable, so the range begins at 1. |
| TPlcrBurstSizeBytes | Integer32 (-1 | 0..4194304) | current | The amount of buffer space (in bytes) assigned to a queue by policer. The value -1 means that the actual value is derived from the corresponding buffer policy's default value. |
| TPlcrBurstSizeBytesOverride | Integer32 (-2 | -1 | 0..4194304) | current | The amount of buffer space (in bytes) assigned to a queue by policer. The value -1 means that the actual value is derived from the corresponding buffer policy's default value. A value of -2 specifies no override. |
| TPlcyMode | INTEGER { none (0), roundRobin (1), weightedRoundRobin (2), weightedDeficitRoundRobin (3) } | current | Port scheduler Policy Mode |
| TPolicerRateType | INTEGER { kbps (1), percentLocalLimit (2) } | current | The type of the PIR/CIR percent rate. The value 'kbps' means the rate is specified in kbps. The value 'percentLocalLimit' means the rate is specified in percentage of local limit. |
| TPolicerWeight | Integer32 (1..100) | current | The relative weight of the specified entity while feeding into the parent. |
| TPolicyID | Unsigned32 (0..65535|65536|65537) | current | The identification number of a policy. |
| TPolicyStatementNameOrEmpty | TNamedItemOrEmpty | current | The name of a policy statement, when an object refers to it. |
| TPortSchedulerCIR | Integer32 (-1 | 0..400000000) | current | The Committed Information Rate (CIR) rate to be used in kbps. The value -1 means maximum rate. |
| TPortSchedulerPIR | Integer32 (-1 | 1..100000000) | current | The Peak Information Rate (PIR) rate to be used in kbps. The value -1 means maximum rate. |
| TPortSchedulerPIRRate | Integer32 (-1 | 1..400000000) | current | The Peak Information Rate (PIR) rate to be used in kbps. The value -1 means maximum rate. |
| TPrecValue | Integer32 (0..7) | current | The precedence bits as used in the IPv4 header. This constitutes of 3 bits and hence can hold the values from 0 to 7. |
| TPrecValueOrNone | Integer32 (-1 | 0..7) | current | The precedence bits as used in the IPv4 header. This constitutes of 3 bits and hence can hold the values from 0 to 7. The value '-1' specifies that the precedence value is undefined/unused. |
| TPriority | INTEGER { low(1), high(2) } | current | the priority to apply to a packet |
| TPriorityOrDefault | INTEGER { low(1), high(2), default(3) } | current | the priority to apply to a packet. when set to default(3), the priority from the default-action is used. |
| TPriorityOrUndefined | INTEGER { undefined(0), low(1), high(2) } | current | the priority to apply to a packet. when set to undefined(0), the priority is not applicable. |
| TProfile | INTEGER { in(1), out(2) } | current | the profile marking of a packet at the ingress. |
| TProfileOrDei | INTEGER { in(1), out(2), use-dei(13) } | current | the profile marking of a packet at the ingress. |
| TProfileOrNone | INTEGER { none (0), in(1), out(2) } | current | Profile marking of a packet. |
| TProfileUseDEOrNone | INTEGER { none (0), in (1), out (2), de (3) } | current | This textual-convention specifies the profile marking of a packet. Value of 'in' specifies in-profile marking. Value of 'out' specifies out-profile marking. Value of 'de' specifies that the profile marking of the packet… |
| TQGroupType | INTEGER { port (0), vpls(1) } | current | This textual-convention specifies the type of the Queue-Group. |
| TQosOverrideType | INTEGER { queue (1), policer (2), aggRateLimit (3), arbiter (4), scheduler (5) } | current | This textual-convention specifies the type of the Qos Override. |
| TQosQGrpInstanceIDorZero | Unsigned32 (0|1..65535) | current | The identifcation number of a QoS queue group instance. The value of '0' indicates the system determined default value. |
| TQPreempt | INTEGER { express (0), preemptable (1) } | current | Specifies the preemption mode for the queue. express - frames queued for the priority are to be transmitted using the express service (eMAC) for the Port preemptable - frames queued for the priority are to be transmitte… |
| TQueueId | Integer32 (0 | 1..32) | current | The value of TQueueId specifies the identification number of a queue. A value of zero (0) indicates that no specific queue identification has been assigned for this object. When an object of type TQueueId is an SNMP tab… |
| TQueueIdOrAll | Integer32 (-1 | 0 | 1..32) | current | The value of TQueueIdOrAll specifies the identification number of a queue A value of zero (0) indicates that no specific queue identification has been assigned for this object. A value of (-1) indicates 'all queues'. |
| TQueueMode | INTEGER { priority(1), profile (2) } | current | The mode in which the queue is operating. If the queue is operating in the 'priority' mode, it is capable of handling traffic differently with two distinct priorities. These priorities are assigned by the stages precedi… |
| TQWeight | Integer32 (0 |1..100) | current | The Queue weight of the specified entity. |
| TRatePercent | Integer32 (0..100) | current | The percentage of maximum rate allowed. |
| TRateType | INTEGER { kbps (1), percent (2) } | current | The type of the PIR/CIR rate. The value 'kbps' means the rate is specified in kbps. The value 'percent' means the rate is specified in percentage |
| TRemarkType | INTEGER { none (1), dscp (2), precedence (3) } | current | The remarking to be used. |
| TSapEgrEncapGroupActionType | INTEGER { create (1), destroy (2) } | current | TSapEgrEncapGroupActionType identifies Encapsulation group action type on SAP egress. It is used to create or destroy row entries in an associated table. |
| TSapEgrEncapGroupType | INTEGER { isid (1) } | current | TSapEgrEncapGroupType identifies Encapsulation group type on SAP egress. |
| TSapEgrEncapGrpQosPolicyIdOrZero | Unsigned32 (0 | 1..65535) | current | TSapEgrEncapGrpQosPolicyIdOrZero identifies SAP egress Encapsulation group QoS policy. The value '0' indicates no QoS policy is set. |
| TSapEgressPolicyID | TPolicyID (1..65535|65536|65537) | current | The identification number of a SAP egress policy. |
| TSapIngressMeterId | Integer32 (0 | 1..32) | current | Ingress Meter Id |
| TSapIngressPolicyID | TPolicyID | current | The identification number of a SAP ingress policy. |
| TSdpEgressPolicyID | TPolicyID | current | The identification number of a SDP egress network policy. |
| TSdpIngressPolicyID | TPolicyID | current | The identification number of a SDP ingress network policy. |
| TSecondaryShaper10GPIRRate | Integer32 (-1 | 1..10000) | current | The secondary shaper PIR rate to be used in Mbps. The value -1 means maximum rate. |
| TSiteOperStatus | INTEGER { up (1), down (2), outOfResource (3) } | current | TSiteOperStatus data type is an enumerated integer that describes the values used to identify the current operational state of a site. |
| TSubHostId | Unsigned32 | current | A number used to uniquely identify a subscriber host in the system |
| TSysResource | Integer32 (-1 | 0..11) | current | The resource allocated for a particular application. The value -1 means maximum rate. |
| TTcpUdpPort | Integer32 (0 | 1..65535) | current | The number of a TCP or UDP port. Well known port numbers include ftp-data(20), ftp(21), telnet(23), smtp(25), http(80), pop3(110), nntp(119), snmp(161), snmptrap(162), etc. |
| TTcpUdpPortOperator | TOperator | current | The operator used for checking on TCP/UDP ports values and ranges |
| TTmplPolicyID | Unsigned32 (1..65535) | current | The identification number of a policy for template objects. |
| TWeight | Integer32 (0..100) | current | The weight of the specified entity while feeding into the parent. |