TRIPPUPS1-MIB
93 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | Counter enterprises Gauge IpAddress NetworkAddress OBJECT-TYPE TimeTicks |
| RFC1213-MIB | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.850 | Nodetripplite | |||
| 1.3.6.1.4.1.850.1 | NodetrippUPS1 | |||
| 1.3.6.1.4.1.850.1.1 | Nodeups | |||
| 1.3.6.1.4.1.850.1.1.1 | NodeupsIdent | |||
| 1.3.6.1.4.1.850.1.1.1.1 | ScalarupsIdentManufacturer | read-only | mandatory | The name of the UPS manufacturer. |
| 1.3.6.1.4.1.850.1.1.1.2 | ScalarupsIdentModel | read-only | mandatory | The UPS Model designation. |
| 1.3.6.1.4.1.850.1.1.1.3 | ScalarupsIdentUPSSoftwareVersion | read-only | mandatory | The UPS Firmware software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations. |
| 1.3.6.1.4.1.850.1.1.1.4 | ScalarupsIdentAgentSoftwareVersion | read-only | mandatory | The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations. |
| 1.3.6.1.4.1.850.1.1.1.5 | ScalarupsIdentName | read-write | mandatory | A string identifying the UPS. This object should be set by the administrator. |
| 1.3.6.1.4.1.850.1.1.1.6 | ScalarupsIdentAttachedDevices | read-write | mandatory | A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator. |
| 1.3.6.1.4.1.850.1.1.2 | NodeupsBattery | |||
| 1.3.6.1.4.1.850.1.1.2.1 | ScalarupsBatteryStatus | read-only | mandatory | The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the batteries are fully charged. A value of bat… |
| 1.3.6.1.4.1.850.1.1.2.2 | ScalarupsSecondsOnBattery | read-only | mandatory | If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last res… |
| 1.3.6.1.4.1.850.1.1.2.3 | ScalarupsEstimatedMinutesRemaining | read-only | mandatory | An estimate of the time to battery charge depletion under the present load conditions if the utility power were to be lost and remain off. UNITS - minutes |
| 1.3.6.1.4.1.850.1.1.2.4 | ScalarupsBatteryChargeRemaining | read-only | mandatory | The estimate of the battery charge remaining expressed as a percent of full charge. |
| 1.3.6.1.4.1.850.1.1.2.5 | ScalarupsBatteryVoltage | read-only | mandatory | The magnitude of the present battery voltage. UNITS 0.1 Volt DC. |
| 1.3.6.1.4.1.850.1.1.2.7 | ScalarupsBatteryTemperature | read-only | mandatory | The ambient temperature at or near the UPS Battery. UNITS degrees Centigrade |
| 1.3.6.1.4.1.850.1.1.3 | NodeupsInput | |||
| 1.3.6.1.4.1.850.1.1.3.1 | ScalarupsInputFrequency | read-only | mandatory | The present input frequency. UNITS 0.1 Hertz |
| 1.3.6.1.4.1.850.1.1.3.2 | ScalarupsInputLineBads | read-only | mandatory | A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. |
| 1.3.6.1.4.1.850.1.1.3.3 | ScalarupsInputNumLines | read-only | mandatory | The number of input lines utilized in this device. This variable indicates the number of rows in the input table. |
| 1.3.6.1.4.1.850.1.1.3.4 | ScalarupsInputVolt | read-only | mandatory | The magnitude of the present input voltage. UNITS RMS Volts |
| 1.3.6.1.4.1.850.1.1.3.5 | TableupsInputTable | not-accessible | mandatory | A list of input table entries. The number of entries is given by the value of upsInputNumLines. |
| 1.3.6.1.4.1.850.1.1.3.5.1 | RowupsInputEntry | not-accessible | mandatory | An entry containing information applicable to a particular input line. |
| 1.3.6.1.4.1.850.1.1.3.5.1.1 | ColumnupsInputLineIndex | read-only | mandatory | The input line identifier. |
| 1.3.6.1.4.1.850.1.1.3.5.1.2 | ColumnupsInputVoltage | read-only | mandatory | The magnitude of the present input voltage. UNITS RMS Volts |
| 1.3.6.1.4.1.850.1.1.4 | NodeupsOutput | |||
| 1.3.6.1.4.1.850.1.1.4.1 | ScalarupsOutputSource | read-only | mandatory | The present source of output power. |
| 1.3.6.1.4.1.850.1.1.4.2 | ScalarupsOutputFrequency | read-only | mandatory | The present output frequency. UNITS 0.1 Hertz |
| 1.3.6.1.4.1.850.1.1.4.3 | ScalarupsOutputNumLines | read-only | mandatory | The number of output lines utilized in this device. This variable indicates the number of rows in the output table. |
| 1.3.6.1.4.1.850.1.1.4.4 | ScalarupsOutputPercLoad | read-only | mandatory | The percentage of true power capacity presently being used. UNITS percent |
| 1.3.6.1.4.1.850.1.1.4.5 | TableupsOutputTable | not-accessible | mandatory | A list of output table entries. The number of entries is given by the value of upsOutputNumLines. |
| 1.3.6.1.4.1.850.1.1.4.5.1 | RowupsOutputEntry | not-accessible | mandatory | An entry containing information applicable to a particular output line. |
| 1.3.6.1.4.1.850.1.1.4.5.1.1 | ColumnupsOutputLineIndex | read-only | mandatory | The output line identifier. |
| 1.3.6.1.4.1.850.1.1.4.5.1.2 | ColumnupsOutputVoltage | read-only | mandatory | The present output voltage. UNITS RMS Volts |
| 1.3.6.1.4.1.850.1.1.4.5.1.3 | ColumnupsOutputCurrent | read-only | mandatory | The present output mandatory. UNITS 0.1 Amp |
| 1.3.6.1.4.1.850.1.1.4.5.1.4 | ColumnupsOutputPower | read-only | mandatory | The present output true power. UNITS Watts |
| 1.3.6.1.4.1.850.1.1.4.5.1.5 | ColumnupsOutputPercentLoad | read-only | mandatory | The percentage of true power capacity presently being used. UNITS percent |
| 1.3.6.1.4.1.850.1.1.6 | NodeupsAlarm | |||
| 1.3.6.1.4.1.850.1.1.6.1 | ScalarupsAlarmsPresent | read-only | mandatory | The present number of active alarm conditions. |
| 1.3.6.1.4.1.850.1.1.6.2 | ScalarupsAlarmID | read-only | mandatory | A unique identifier for an alarm condition. This value must remain constant. |
| 1.3.6.1.4.1.850.1.1.6.3 | ScalarupsAlarmDESCR | read-only | mandatory | A reference to an alarm description object. The object references should not be accessible, but rather be used to provide a unique description of the alarm con… |
| 1.3.6.1.4.1.850.1.1.6.4 | TableupsAlarmTable | not-accessible | mandatory | A list of alarm table entries. The table consists of zero, one, or may rows at any moment, depending upon the number of alarm conditions in effect. The table i… |
| 1.3.6.1.4.1.850.1.1.6.4.1 | RowupsAlarmEntry | not-accessible | mandatory | An entry containing information applicable to a particular alarm. |
| 1.3.6.1.4.1.850.1.1.6.4.1.1 | ColumnupsAlarmId | read-only | mandatory | A unique identifier for an alarm condition. This value must remain constant. |
| 1.3.6.1.4.1.850.1.1.6.4.1.2 | ColumnupsAlarmDescr | read-only | mandatory | A reference to an alarm description object. The object references should not be accessible, but rather be used to provide a unique description of the alarm con… |
| 1.3.6.1.4.1.850.1.1.6.4.1.3 | ColumnupsAlarmTime | read-only | mandatory | The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumable existed before ag… |
| 1.3.6.1.4.1.850.1.1.7 | NodeupsWellKnownAlarms | |||
| 1.3.6.1.4.1.850.1.1.7.1 | ScalarupsAlarmBatteryBad | read-only | mandatory | One or more batteries have been determined to require replacement. |
| 1.3.6.1.4.1.850.1.1.7.2 | ScalarupsAlarmOnBattery | read-only | mandatory | The UPS is drawing power from the batteries. |
| 1.3.6.1.4.1.850.1.1.7.3 | ScalarupsAlarmLowBattery | read-only | mandatory | The remaining battery run-time is less than or equal to upsConfigMinutesRemaining. |
| 1.3.6.1.4.1.850.1.1.7.4 | ScalarupsAlarmDepletedBattery | read-only | mandatory | The UPS will be unable to sustain the present load when and if the utility power is lost. |
| 1.3.6.1.4.1.850.1.1.7.5 | ScalarupsAlarmTempBad | read-only | mandatory | A temperature is out of tolerance. |
| 1.3.6.1.4.1.850.1.1.7.6 | ScalarupsAlarmOutputOverload | read-only | mandatory | The output load exceeds the UPS output capacity. |
| 1.3.6.1.4.1.850.1.1.7.7 | ScalarupsAlarmOutputOffAsRequested | read-only | mandatory | The UPS has shutdown as commanded, i.e., the output is off. |
| 1.3.6.1.4.1.850.1.1.7.8 | ScalarupsAlarmUpsOutputOff | read-only | mandatory | The UPS is in the off state. |
| 1.3.6.1.4.1.850.1.1.7.9 | ScalarupsAlarmDiagnosticTestFailed | read-only | mandatory | The result of the last diagnostic test indicates a failure. |
| 1.3.6.1.4.1.850.1.1.7.10 | ScalarupsAlarmCommunicationsLost | read-only | mandatory | A problem has been encountered in the communications between the agent and the UPS. |
| 1.3.6.1.4.1.850.1.1.7.11 | ScalarupsAlarmShutdownPending | read-only | mandatory | A upsShutdownAfterDelay countdown is underway. |
| 1.3.6.1.4.1.850.1.1.7.12 | ScalarupsAlarmShutdownImminent | read-only | mandatory | A upsShutdownAfterDelay countdown is underway. |
| 1.3.6.1.4.1.850.1.1.7.13 | ScalarupsAlarmTestInProgress | read-only | mandatory | A upsShutdownAfterDelay countdown is underway. |
| 1.3.6.1.4.1.850.1.1.8 | NodeupsTest | |||
| 1.3.6.1.4.1.850.1.1.8.1 | ScalarupsTestId | read-write | mandatory | The test named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of test, including the well known tests identified in this document… |
| 1.3.6.1.4.1.850.1.1.8.2 | ScalarupsTestResultsSummary | read-only | mandatory | The results of the mandatory or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) are self-documenting. The val… |
| 1.3.6.1.4.1.850.1.1.9 | NodeupsControl | |||
| 1.3.6.1.4.1.850.1.1.9.1 | ScalarupsShutdownType | read-write | mandatory | Setting this object will start the output after the indicated number of seconds. Setting this object to 0 will cause the UPS to start the output immediately. I… |
| 1.3.6.1.4.1.850.1.1.9.2 | ScalarupsShutdownAfterDelay | read-write | mandatory | Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShhutdownType at the time of shutd… |
| 1.3.6.1.4.1.850.1.1.9.3 | ScalarupsStartupAfterDelay | read-write | mandatory | Setting this object will start the output after the indicated number of seconds, includeing starting the UPS, if necessary. Setting this object to 0 will cause… |
| 1.3.6.1.4.1.850.1.1.9.4 | ScalarupsRebootDuration | read-write | mandatory | Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of the upsShutdownType at th… |
| 1.3.6.1.4.1.850.1.1.9.5 | ScalarupsAutoRestart | read-write | mandatory | Setting this object to 'on' will cause the UPS system to restart after a shutdown if/when utility power is present. |
| 1.3.6.1.4.1.850.1.1.10 | NodeupsConfig | |||
| 1.3.6.1.4.1.850.1.1.10.11 | ScalarupsConfigInputVoltageHigh | read-write | mandatory | If the value of the input voltage (in Volts) exceeds this value, a utilityVoltageHigh trap will be triggered. |
| 1.3.6.1.4.1.850.1.1.10.12 | ScalarupsConfigInputVoltageLow | read-write | mandatory | If the value of the input voltage (in Volts) falls below this value, a utilityVoltageLow trap will be triggered. |
| 1.3.6.1.4.1.850.1.1.10.13 | ScalarupsConfigOutputPercLoadHigh | read-write | mandatory | If the value of the output percent load exceeds this value, a upsOverload trap will be triggered. |
| 1.3.6.1.4.1.850.1.1.10.14 | ScalarupsConfigBatteryPercLow | read-write | mandatory | If the value of the battery percent capacity falls below this value, a lowBattery trap will be triggered. |
| 1.3.6.1.4.1.850.1.1.10.15 | ScalarupsConfigBatteryTemperatureHigh | read-write | mandatory | If the value of the battery temperature exceeds this value, a batteryTemperatureHigh trap will be triggered. |
| 1.3.6.1.4.1.850.5 | NodeupsOnBattery | The UPS is on battery. | ||
| 1.3.6.1.4.1.850.6 | NodepowerRestored | Utility power has been restored. | ||
| 1.3.6.1.4.1.850.7 | NodelowBattery | The UPS batteries are low and will soon be exhausted. | ||
| 1.3.6.1.4.1.850.8 | NodereturnFromLowBattery | The UPS has returned from a low battery condition. | ||
| 1.3.6.1.4.1.850.9 | NodecommunicationEstablished | Communication with the UPS has been established. This trap will be sent each time there is a transition from a power off condition to a power on condition. | ||
| 1.3.6.1.4.1.850.10 | NodecommunicationLost | Communication with the UPS has been lost. | ||
| 1.3.6.1.4.1.850.11 | NodeupsOverload | The UPS has sensed a load greater than the value of the upsConfigOutputPercLoadHigh MIB variable. | ||
| 1.3.6.1.4.1.850.12 | NodeupsDiagnosticsFailed | The UPS failed its self-test. | ||
| 1.3.6.1.4.1.850.13 | NodeupsDiagnosticsPassed | The UPS passed its internal self-test. | ||
| 1.3.6.1.4.1.850.14 | NodeutilityVoltageHigh | The UPS input voltage greater than or equal to the value of the upsConfigInputVoltageHigh MIB variable. | ||
| 1.3.6.1.4.1.850.15 | NodeutilityVoltageLow | The UPS input voltage is less than or equal to the value of the upsConfigInputVoltageLow MIB variable. | ||
| 1.3.6.1.4.1.850.16 | NodeutilityVoltageReturnToNormal | The UPS has returned from a utility voltage high or low condition. | ||
| 1.3.6.1.4.1.850.17 | NodebatteryTemperatureHigh | The UPS battery temperature has exceeded the value of the upsConfigBatteryTemperatureHigh MIB variable. | ||
| 1.3.6.1.4.1.850.18 | NodeshutdownPending | A UPS shutdown countdown is underway. | ||
| 1.3.6.1.4.1.850.19 | NodeupsSleeping | The output of the UPS has been turned off. | ||
| 1.3.6.1.4.1.850.20 | NodeupsWokeup | The output of the UPS has been turned on. | ||
| 1.3.6.1.4.1.850.21 | NodeupsBatteryNeedsReplacement | The UPS battery needs to be replaced. |