TROPIC-SYNCE-MIB
95 objects
Synchronous Ethernet MIB attributes.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.7483.1.1.2.2.4.6 | IdentitytnSyncEMibModule | of | Synchronous Ethernet MIB attributes. | |
| 1.3.6.1.4.1.7483.2.2.4.8.1 | NodetnSyncEConf | |||
| 1.3.6.1.4.1.7483.2.2.4.8.1.1 | NodetnSyncEGroups | |||
| 1.3.6.1.4.1.7483.2.2.4.8.1.1.1 | GrouptnSyncEGroup | current | . | |
| 1.3.6.1.4.1.7483.2.2.4.8.1.1.2 | GrouptnSyncELineRefGroup | current | . | |
| 1.3.6.1.4.1.7483.2.2.4.8.1.1.3 | GrouptnSyncEControlGroup | current | . | |
| 1.3.6.1.4.1.7483.2.2.4.8.1.1.4 | GrouptnSyncEPortGroup | current | . | |
| 1.3.6.1.4.1.7483.2.2.4.8.1.1.5 | GrouptnSyncEStationClockGroup | current | . | |
| 1.3.6.1.4.1.7483.2.2.4.8.1.1.6 | GrouptnSyncEBITSPortGroup | current | . | |
| 1.3.6.1.4.1.7483.2.2.4.8.1.1.7 | GrouptnWanGroup | current | . | |
| 1.3.6.1.4.1.7483.2.2.4.8.1.1.8 | GrouptnSyncEPacketswitchControlGroup | current | . | |
| 1.3.6.1.4.1.7483.2.2.4.8.1.2 | NodetnSyncECompliances | |||
| 1.3.6.1.4.1.7483.2.2.4.8.1.2.1 | CompliancetnSyncECompliance | current | . | |
| 1.3.6.1.4.1.7483.2.2.4.8.2 | NodetnSyncEObjs | |||
| 1.3.6.1.4.1.7483.2.2.4.8.2.1 | NodetnSyncEBasics | |||
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.1 | TabletnSyncETable | not-accessible | current | Table of Sync-E attributes. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1 | RowtnSyncEEntry | not-accessible | current | . |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.1 | ColumntnSyncESyncMsg | read-create | current | Determines if the timing reference selection for system timing uses Synchronization Status Message (SSM) Quality Levels or Enhanced Quality Levels. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.2 | ColumntnSyncEActiveRef | read-only | current | The ID of the association line reference. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.3 | ColumntnSyncEWTR | read-create | current | The system timing WTR. Current configurable range: 0 to 12, and 999999. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.4 | ColumntnSyncESwCmdLineRef | read-create | current | The third byte represents the switch command: 1 - nocmd 2 - clear 3 - lockout 4 - forceswitch 5 - mannual 6 - auto 7 - clearlockout. The last byte represents t… |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.5 | ColumntnSyncEClkModState | read-only | current | The Sync-E clock mode state. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.6 | ColumntnSyncESystemQL | read-only | current | The value of the system quality level (SSM), shown in following: 31 - not applicable When the NE is in SDH mode: 0 - quality unknown 1 - PRC 2 - SSU_A 3 - SSU_… |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.7 | ColumntnSyncEQLDegradeThreshold | read-create | current | The threshold value of SSM quality level degradation for systme timing reference. When the NE is in SDH mode: 1 - PRC 2 - SSU_A 3 - SSU_B 4 - SEC - Default 23 … |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.8 | ColumntnSyncECurrentActiveLineRefFreqOff | read-only | current | The current frequency offset of the active timing reference. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.9 | ColumntnSyncEAlmProfName | read-create | current | . |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2 | TabletnSyncELineRefTable | not-accessible | current | Table of VTS map. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1 | RowtnSyncELineRefEntry | not-accessible | current | . |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.1 | ColumntnSyncELineRefIndex | not-accessible | current | The ifIndex of the line reference table. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.2 | ColumntnSyncELineRefAssignedPort | read-create | current | The assigned port for the line reference. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.3 | ColumntnSyncELineRefPriority | read-create | current | Line reference priority. Current configurable range: 0 to 8. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.4 | ColumntnSyncELineRefAdminState | read-create | current | The administrative state of the line reference. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.5 | ColumntnSyncELineRefOperState | read-only | current | The operating state of the line reference. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.6 | ColumntnSyncELineLockOut | read-only | current | If lock out line reference or not. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.7 | ColumntnSyncELineRefState | read-only | current | The Sync-E line reference state. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.8 | ColumntnSyncELineRefSwState | read-only | current | The Sync-E line reference switch state. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.9 | ColumntnSyncELineRefIncSSMMsg | read-only | current | This object indicates the current value of incoming QL on that port. 30 - unstable 31 - not applicable When the NE works in SDH mode: 0 - Unknown 1 - PRC 2 - S… |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.10 | ColumntnSyncELineRefIncSSMStatus | read-only | current | This object indicates the current status of incoming QL on that port. 0: Valid 1: Invalid 2: Not Supported 3: Not Applicable It's applicable only to the timing… |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.11 | ColumntnSyncELineRefIncSSMSupp | read-create | current | Enable or disable the line reference incoming QL processing. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.12 | ColumntnSyncELineRefProvQL | read-create | current | Manually provisioned incoming SSM value for the line reference. The value can be: 0 - AUTO When the NE is in SDH mode: 1 - PRC 2 - SSU_A 3 - SSU_B 4 - SEC 5 - … |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.13 | ColumntnSyncELineRefAssociatedPort | read-create | current | The associated physical port of the line reference. This parameter replaces tnSyncELineRefAssignedPort in order to support assigning a line reference to a port… |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.14 | ColumntnSyncELineRefPriorityOfStationClock | read-create | current | Line reference priority for the output station clock. Current configurable range: 0 to 8. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.15 | ColumntnSyncELineRefLockOutOfStationClock | read-only | current | If lock out the line reference or not for the output station clock. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.16 | ColumntnSyncELineRefSwStateOfStationClock | read-only | current | The Sync-E line reference switch state of the output station clock. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.17 | ColumntnSyncELineRefCurrentFreqOff | read-only | current | The current frequency offset of the timing reference. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.18 | ColumntnSyncELineRefAlmProfName | read-create | current | . |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.19 | ColumntnSyncELineRefIncExtdQLTLVClockID | read-only | current | Incoming Extended QL TLV Clock ID. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.20 | ColumntnSyncELineRefIncExtdQLTLVMixedClockType | read-only | current | Incoming Extended QL TLV Mixed Clock Type Flag. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.21 | ColumntnSyncELineRefIncExtdQLTLVPartialChain | read-only | current | Incoming Extended QL TLV Partial Chain Flag. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.22 | ColumntnSyncELineRefIncExtdQLTLVNumeEEC | read-only | current | Incoming Extended QL TLV Number of eEEC. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.23 | ColumntnSyncELineRefIncExtdQLTLVNumEEC | read-only | current | Incoming Extended QL TLV Number of EEC. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.24 | ColumntnSyncELineRefProvQLOfStationClock | read-create | current | Manually provisioned incoming SSM value of the line reference output timing. The value can be: 0 - AUTO When the NE is in SDH mode: 1 - PRC 2 - SSU_A 3 - SSU_B… |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.25 | ColumntnSyncELineRefIncSSMMsgOfStationClock | read-only | current | This object indicates the current value of incoming QL for output timing on that port. 30 - unstable 31 - not applicable When the NE works in SDH mode: 0 - Unk… |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.26 | ColumntnSyncELineRefIncSSMStatusOfStationClock | read-only | current | This object indicates the current status of incoming QL on that port for output timing. 0: Valid 1: Invalid 2: Not Supported 3: Not Applicable It's applicable … |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.3 | TabletnSyncEControlTable | not-accessible | current | Table of Sync-E Control attributes. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.3.1 | RowtnSyncEControlEntry | not-accessible | current | . |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.3.1.1 | ColumntnSyncEControlEECEnable | read-create | current | enable - The Synchronous Ethernet is supported for the pack and the synchronization attributes can be configured. disable - The Synchronous Ethernet is not sup… |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.4 | TabletnSyncEPortTable | not-accessible | current | Table of Sync-E Port attributes. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.4.1 | RowtnSyncEPortEntry | not-accessible | current | . |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.4.1.1 | ColumntnSyncEOprMode | read-create | current | The port Synchronous Ethernet Operation Mode. When the port is in SYNC mode, recovered clock of its input signal can be selected as a reference clock to the sy… |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.4.1.2 | ColumntnSyncEOutgoingForceSsmTrans | read-create | current | The port SSM/Quality Level Transmission value. The value can be: In SDH mode - act, prc, ssua, ssub, sec, dnu, ePRTC, PRTC, ePRC, eSEC, none; In sonet mode - a… |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.5 | TabletnSyncEStationClockTable | not-accessible | current | Table of Sync-E station clock attributes. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1 | RowtnSyncEStationClockEntry | not-accessible | current | . |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.1 | ColumntnSyncEStationClockSyncMsg | read-create | current | Determines if the timing reference selection for station clock timing uses Synchronization Status Message (SSM) Quality Levels or Enhanced Quality Levels. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.2 | ColumntnSyncEStationClockActiveRef | read-only | current | The ID of the association line reference. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.3 | ColumntnSyncEStationClockWTR | read-create | current | The station clock timing WTR. Current configurable range: 0 to 12, and 999999. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.4 | ColumntnSyncEStationClockSwCmdLineRef | read-create | current | The third byte represents the switch command: 1 - nocmd 2 - clear 3 - lockout 4 - forceswitch 5 - mannual 6 - auto 7 - clearlockout. The last byte represents t… |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.5 | ColumntnSyncEStationClockSystemQL | read-only | current | The value of the system quality level (SSM) for the output timing clock, shown in following: 31 - not applicable When the NE is in SDH mode: 0 - quality unknow… |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.6 | ColumntnSyncEStationClockQLThreshold | read-create | current | Specifies the threshold value for the quality level i.e., SSM value for squelching the output towards timing output. If the quality value of the current select… |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.7 | ColumntnSyncEStationClockOutSel | read-create | current | Specifies which signal is selected for the output station clock: OUTTIM - Output is selected from output timing selection process SETG - Output is selected fro… |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.8 | ColumntnSyncEStationClockAlmProfName | read-create | current | . |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.6 | TabletnSyncEBITSPortTable | not-accessible | current | Table of BITS port attributes. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1 | RowtnSyncEBITSPortEntry | not-accessible | current | . |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.1 | ColumntnSyncEBITSPortDirection | read-create | current | Indicate the direction of the BITS port. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.2 | ColumntnSyncEBITSPortSignalType | read-create | current | Specify the signal type for the BITS interface: 0 - 2MHz 1 - unframed E1 2 - framed E1 without SSM 3 - framed E1 with SSM 4 - DS1 SF 5 - DS1 ESF. In SDH mode, … |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.3 | ColumntnSyncEBITSPortSaBit | read-create | current | Specifies the Sa bit location used to carry the SSM information. This parameter is only applicable when tnSyncEBITSPortSignalType = 3 (framed E1 with SSM) |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.4 | ColumntnSyncEBITSPortOutputSSMTrans | read-create | current | The port SSM/Quality Level Transmission value. The value can be: In SDH mode - act, prc, ssua, ssub, sec, dnu, none; In sonet mode - act, stu, prs, st2, sts3e,… |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.5 | ColumntnSyncEBITSPortOutputAISMode | read-create | current | Specifies which signal is inserted for the timing output port if the output signal is squelched. The parameter is only applicable for output port types support… |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.6 | ColumntnSyncEBITSPortLineImpedance | read-create | current | Nominal line impedance. When in SDH mode, imp75ohms or imp120ohms could be used and the default is imp120ohms. When in ONET mode, imp100ohms could be used and … |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.7 | ColumntnSyncEBITSPortLineCode | read-create | current | Line code. This attribute is applicable when tnSyncEBITSPortSignalType is DS1 SF or DS1 ESF. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.8 | ColumntnSyncEBITSPortLbo | read-create | current | Line equalization value for the BITS output port, taking one of the following values: - lbo: no compensation - lbo1: 0 to 133 feet - lbo2: 133 to 266 feet - lb… |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.9 | ColumntnSyncEBITSPortAlmProfName | read-create | current | Alarm profile for BITs port |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.7 | TabletnWanTable | not-accessible | current | Table of Wan attributes. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1 | RowtnWanEntry | not-accessible | current | . |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.1 | ColumntnWanAlmProfName | read-create | current | . |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.2 | ColumntnWanSyncEOprMode | read-create | current | The Synchronous Ethernet Operation Mode. When in SYNC mode, recovered clock of its input signal can be selected as a reference clock to the system clock.When i… |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.3 | ColumntnWanSyncEOutgoingForceSsmTrans | read-create | current | The port SSM/Quality Level Transmission value. The value can be: In SDH mode - act, prc, ssua, ssub, sec, dnu, ePRTC, PRTC, ePRC, eSEC, none. In SONET mode - a… |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.4 | ColumntnWanAdminStatus | read-create | current | Wan administrative state. It may be used to suppress the alarms or disable consequent actions on the WAN entity. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.5 | ColumntnWanOperStatus | read-only | current | operational state of WAN entity |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.6 | ColumntnWanStateQualifier | read-only | current | Indicates the state qualifier (i.e., the secondary state) of the WAN state. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.7 | ColumntnWanOperationalCapability | read-only | current | The partiallyEnabled(3) state means an abnormal state. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.8 | ColumntnWanDescription | read-create | current | Wan Description. |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.8 | TabletnSyncEPacketswitchControlTable | not-accessible | current | Table of Sync-E Control attributes for a packetswitch. This table provides the same functionality as tnSyncEControlTable, but requires a switchid as an index |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.8.1 | RowtnSyncEPacketswitchControlEntry | not-accessible | current | . |
| 1.3.6.1.4.1.7483.2.2.4.8.2.1.8.1.1 | ColumntnSyncEPacketswitchControlEECEnable | read-create | current | enable - Synchronous Ethernet is supported for the packetswitch and the synchronization attributes can be configured. disable - Synchronous Ethernet is not sup… |