USWI-sysSettings-MIB
108 objects
system_settings
Imported Objects
| RFC1155-SMI | enterprises -- IpAddress |
| SNMPv2-SMI | MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.43242 | Nodeuswi | |||
| 1.3.6.1.4.1.43242.1 | IdentitysysSettings | system_settings | ||
| 1.3.6.1.4.1.43242.1.1 | Scalaroutputs | read-only | current | Largest Output. |
| 1.3.6.1.4.1.43242.1.2 | Scalarinputs | read-only | current | Largest Input. |
| 1.3.6.1.4.1.43242.1.3 | Scalarmodules | read-only | current | Number of modules for which the system is configured |
| 1.3.6.1.4.1.43242.1.4 | ScalarlastQueryError | read-only | current | Last query error or zero. |
| 1.3.6.1.4.1.43242.1.5 | ScalarmoduleSlot | read-write | current | Set: (see Note 2 in programmers guide in GET? and SET Values section) Get: returns the slot where the module should be. |
| 1.3.6.1.4.1.43242.1.6 | ScalarinputsOnModule | read-write | current | Set: (see Note 2 in programmers guide in GET? and SET Values section) Get: returns the number of inputs on the module. |
| 1.3.6.1.4.1.43242.1.7 | ScalaroutputsOnModule | read-write | current | Set: (see Note 2 in programmers guide in GET? and SET Values section) Get: returns the number of outputs on the module |
| 1.3.6.1.4.1.43242.1.8 | Scalarslots | read-only | current | Number of slots in the system. |
| 1.3.6.1.4.1.43242.1.9 | ScalarmodInSlot | read-write | current | Set: (see Note 2 in programmers guide in GET? and SET Values section) Get: returns module number in slot or 0 |
| 1.3.6.1.4.1.43242.1.10 | ScalarmodIDinSlot | read-write | current | Set: (see Note 2 in programmers guide in GET? and SET Values section) Get: returns module number in slot or 0 |
| 1.3.6.1.4.1.43242.1.15 | ScalarfaultFIFO | read-only | current | Returns next fault or zero if empty, This is shared between all the interfaces. The Fault bit in the SBR clears once it is empty. |
| 1.3.6.1.4.1.43242.1.16 | ScalarlastExeError | read-only | current | Last error or zero, As long as the register's corresponding bit in SESR is set, the GET? Command returns the last error. Once the SESR has been cleared (by the… |
| 1.3.6.1.4.1.43242.1.20 | ScalargangedModules | read-write | current | 0(False) is unganged, 1(True) is ganged |
| 1.3.6.1.4.1.43242.1.21 | ScalarautoInterlock | read-write | current | Auto interlock on (1) or off (0) |
| 1.3.6.1.4.1.43242.1.22 | ScalarautoRestore | read-write | current | Auto restore on(1) off(0) |
| 1.3.6.1.4.1.43242.1.23 | ScalardebugMode | read-write | current | 1: SPI traffic appears on Telnet port, 0: no traffic on port |
| 1.3.6.1.4.1.43242.1.24 | ScalarbeepOnError | read-write | current | Beep on error (1) or silent (0) default is 1 |
| 1.3.6.1.4.1.43242.1.25 | ScalarinactivityTimeout | read-write | current | TCP/IP port inactivity timeout in seconds. Values: 0 - disabled (i.e. port remains open until closed by host or the FORceclose command) 1 - 28800 (8 hours) - n… |
| 1.3.6.1.4.1.43242.1.26 | ScalarpowerSupply1 | read-only | current | Last status returned from PS1 |
| 1.3.6.1.4.1.43242.1.27 | ScalarpowerSupply2 | read-only | current | Last status returned from PS2 |
| 1.3.6.1.4.1.43242.1.28 | Scalarmemories | read-only | current | number of memories available to SAV or RCL |
| 1.3.6.1.4.1.43242.1.32 | ScalarlastCommandError | read-only | current | Last error or zero As long as the register's corresponding bit in SESR is set, the GET? Command returns the last error. Once the SESR has been cleared (by the … |
| 1.3.6.1.4.1.43242.1.33 | ScalarcpusCurrentIpAddress1 | read-only | current | nnn of nnn.XXX.XXX.XXX for current IP address |
| 1.3.6.1.4.1.43242.1.34 | ScalarcpusCurrentIpAddress2 | read-only | current | nnn of XXX.nnn.XXX.XXX for current IP address |
| 1.3.6.1.4.1.43242.1.35 | ScalarcpusCurrentIpAddress3 | read-only | current | nnn of XXX.XXX.nnn.XXX for current IP address |
| 1.3.6.1.4.1.43242.1.36 | ScalarcpusCurrentIpAddress4 | read-only | current | nnn of XXX.XXX.XXX.nnn for current IP address |
| 1.3.6.1.4.1.43242.1.37 | ScalarcpusCurrentSubnetmask1 | read-only | current | nnn of nnn.XXX.XXX.XXX for current subnet mask |
| 1.3.6.1.4.1.43242.1.38 | ScalarcpusCurrentSubnetmask2 | read-only | current | nnn of XXX.nnn.XXX.XXX for current subnet mask |
| 1.3.6.1.4.1.43242.1.39 | ScalarcpusCurrentSubnetmask3 | read-only | current | nnn of XXX.XXX.nnn.XXX for current subnet mask |
| 1.3.6.1.4.1.43242.1.40 | ScalarcpusCurrentSubnetmask4 | read-only | current | nnn of XXX.XXX.XXX.nnn for current subnet mask |
| 1.3.6.1.4.1.43242.1.41 | Scalarcpu_1IpAddressAfterReset1 | read-write | current | nnn of nnn.XXX.XXX.XXX for IP address after next reset |
| 1.3.6.1.4.1.43242.1.42 | Scalarcpu_1IpAddressAfterReset2 | read-write | current | nnn of XXX.nnn.XXX.XXX for IP address after next reset |
| 1.3.6.1.4.1.43242.1.43 | Scalarcpu_1IpAddressAfterReset3 | read-write | current | nnn of XXX.XXX.nnn.XXX for IP address after next reset |
| 1.3.6.1.4.1.43242.1.44 | Scalarcpu_1IpAddressAfterReset4 | read-write | current | nnn of XXX.XXX.XXX.nnn for IP address after next reset |
| 1.3.6.1.4.1.43242.1.45 | Scalarcpu_1SubnetmaskAfterReset1 | read-write | current | nnn of nnn.XXX.XXX.XXX for subnet mask after next reset |
| 1.3.6.1.4.1.43242.1.46 | Scalarcpu_1SubnetmaskAfterReset2 | read-write | current | nnn of XXX.nnn.XXX.XXX for subnet mask after next reset |
| 1.3.6.1.4.1.43242.1.47 | Scalarcpu_1SubnetmaskAfterReset3 | read-write | current | nnn of XXX.XXX.nnn.XXX for subnet mask after next reset |
| 1.3.6.1.4.1.43242.1.48 | Scalarcpu_1SubnetmaskAfterReset4 | read-write | current | nnn of XXX.XXX.XXX.nnn for subnet mask after next reset |
| 1.3.6.1.4.1.43242.1.49 | ScalarcpusCurrentgateway1 | read-only | current | nnn of nnn.XXX.XXX.XXX for current Gateway address |
| 1.3.6.1.4.1.43242.1.50 | ScalarcpusCurrentgateway2 | read-only | current | nnn of XXX.nnn.XXX.XXX for current Gateway address |
| 1.3.6.1.4.1.43242.1.51 | ScalarcpusCurrentgateway3 | read-only | current | nnn of XXX.XXX.nnn.XXX for current Gateway address |
| 1.3.6.1.4.1.43242.1.52 | ScalarcpusCurrentgateway4 | read-only | current | nnn of XXX.XXX.XXX.nnn for current Gateway address |
| 1.3.6.1.4.1.43242.1.53 | Scalarcpu_1GatewayAfterReset1 | read-write | current | nnn of nnn.XXX.XXX.XXX for gateway mask after next reset |
| 1.3.6.1.4.1.43242.1.54 | Scalarcpu_1GatewayAfterReset2 | read-write | current | nnn of XXX.nnn.XXX.XXX for gateway mask after next reset |
| 1.3.6.1.4.1.43242.1.55 | Scalarcpu_1GatewayAfterReset3 | read-write | current | nnn of XXX.XXX.nnn.XXX for gateway mask after next reset |
| 1.3.6.1.4.1.43242.1.56 | Scalarcpu_1GatewayAfterReset4 | read-write | current | nnn of XXX.XXX.XXX.nnn for gateway mask after next reset |
| 1.3.6.1.4.1.43242.1.57 | Scalarcpu_2IpAddressAfterReset1 | read-write | current | nnn of nnn.XXX.XXX.XXX for IP address after next reset |
| 1.3.6.1.4.1.43242.1.58 | Scalarcpu_2IpAddressAfterReset2 | read-write | current | nnn of XXX.nnn.XXX.XXX for IP address after next reset |
| 1.3.6.1.4.1.43242.1.59 | Scalarcpu_2IpAddressAfterReset3 | read-write | current | nnn of XXX.XXX.nnn.XXX for IP address after next reset |
| 1.3.6.1.4.1.43242.1.60 | Scalarcpu_2IpAddressAfterReset4 | read-write | current | nnn of XXX.XXX.XXX.nnn for IP address after next reset |
| 1.3.6.1.4.1.43242.1.61 | Scalarcpu_1SerialPortSetting | read-write | current | weighted value |
| 1.3.6.1.4.1.43242.1.62 | Scalarcpu_2SerialPortSetting | read-write | current | weighted value |
| 1.3.6.1.4.1.43242.1.63 | Scalarcpu_2SubnetmaskAfterReset1 | read-write | current | nnn of nnn.XXX.XXX.XXX for subnet mask after next reset |
| 1.3.6.1.4.1.43242.1.64 | Scalarcpu_2SubnetmaskAfterReset2 | read-write | current | nnn of XXX.nnn.XXX.XXX for subnet mask after next reset |
| 1.3.6.1.4.1.43242.1.65 | Scalarcpu_2SubnetmaskAfterReset3 | read-write | current | nnn of XXX.XXX.nnn.XXX for subnet mask after next reset |
| 1.3.6.1.4.1.43242.1.66 | Scalarcpu_2SubnetmaskAfterReset4 | read-write | current | nnn of XXX.XXX.XXX.nnn for subnet mask after next reset |
| 1.3.6.1.4.1.43242.1.69 | Scalarcpu_1SerialPortInstalled | read-only | current | 0: no, 1: yes |
| 1.3.6.1.4.1.43242.1.70 | Scalarcpu_2SerialPortInstalled | read-only | current | 0: no, 1: yes |
| 1.3.6.1.4.1.43242.1.71 | Scalarcpu_2GatewayAfterReset1 | read-write | current | nnn of nnn.XXX.XXX.XXX for gateway mask after next reset |
| 1.3.6.1.4.1.43242.1.72 | Scalarcpu_2GatewayAfterReset2 | read-write | current | nnn of XXX.nnn.XXX.XXX for gateway mask after next reset |
| 1.3.6.1.4.1.43242.1.73 | Scalarcpu_2GatewayAfterReset3 | read-write | current | nnn of XXX.XXX.nnn.XXX for gateway mask after next reset |
| 1.3.6.1.4.1.43242.1.74 | Scalarcpu_2GatewayAfterReset4 | read-write | current | nnn of XXX.XXX.XXX.nnn for gateway mask after next reset |
| 1.3.6.1.4.1.43242.1.77 | ScalardhcpClient | read-write | current | 0: disable(default), 1: enable |
| 1.3.6.1.4.1.43242.1.78 | ScalarnetworkIdNumber | read-write | current | A number between 0 and 255.default is 0. see note 6 in program guide |
| 1.3.6.1.4.1.43242.1.79 | ScalarpowerSupplyMonitoringDisabling | read-write | current | 0,1,2,or 3. 0:both power supplies are monitored 1:power supply 1 is not monitored 2:power supply 2 is not monitored 3:no power supply is being monitored. see n… |
| 1.3.6.1.4.1.43242.1.80 | ScalardualFaultConditionMask | read-write | current | a number between 0 and 15.default is 0 for backwards compatible but a different factory default can be specified for each project. see note8 in program guide |
| 1.3.6.1.4.1.43242.1.83 | ScalarthePoleToWhichTheModuleBelongs | read-write | current | set: see note2 in program guide, GET:returns,-1,for a valid pole,for a module, returns the pole to which it belongs. for the case where pole 0 is invalid, retu… |
| 1.3.6.1.4.1.43242.1.84 | ScalarlsiIdentification | read-write | current | 0, or 1 where: 0 for off(default), 1 for on |
| 1.3.6.1.4.1.43242.1.86 | ScalarserialCommunicationMode | read-write | current | 0,1,2,3 or 4 where: 0: RS232(default) 1: RS485 with term 2: RS422 without term 3: RS485 without term 4: RS422 with term |
| 1.3.6.1.4.1.43242.1.200 | Scalarval | read-only | current | Checks in input and output are in range without sending anything to the module CPU |
| 1.3.6.1.4.1.43242.1.201 | Scalarstb | read-only | current | Get the status of STB |
| 1.3.6.1.4.1.43242.1.202 | Scalaresr | read-only | current | Get the status of ESR |
| 1.3.6.1.4.1.43242.1.203 | Scalarese | read-write | current | Get: the status of ESER. set: ESER bits based on received value |
| 1.3.6.1.4.1.43242.1.204 | Scalarsre | read-write | current | Get: the status of ESER.set: SRER bits based on the received value |
| 1.3.6.1.4.1.43242.1.205 | Scalarcls | read-write | current | Clears the Last Error Registers, Event Status Register and the Status Byte Register (except for MAV, FLT and PSFLT) but not its queued responses |
| 1.3.6.1.4.1.43242.1.206 | Scalarrst | read-write | current | Clears all switchpoint routings in all modules |
| 1.3.6.1.4.1.43242.1.207 | Scalartst | read-only | current | Selftest/moduleR |
| 1.3.6.1.4.1.43242.1.208 | Scalaridn | read-only | current | Displays system model# and rev# |
| 1.3.6.1.4.1.43242.1.209 | Scalaropc | read-write | current | Get:always return 1,Set: ESR bit1 |
| 1.3.6.1.4.1.43242.1.210 | Scalarsav | read-write | current | Store |
| 1.3.6.1.4.1.43242.1.211 | Scalarrcl | read-write | current | Recall |
| 1.3.6.1.4.1.43242.1.212 | Scalarpsc | read-write | current | Get:returns the current value of PSC.Set: the integer value n (0 or 1) in the PSC register. If the register is 1, ESER and SRER are cleared on each restart. If… |
| 1.3.6.1.4.1.43242.1.213 | Scalarres | read-write | current | System Reset |
| 1.3.6.1.4.1.43242.1.214 | Scalarloc | read-write | current | Keypad lock |
| 1.3.6.1.4.1.43242.1.215 | Scalarunl | read-write | current | Keypad unlock |
| 1.3.6.1.4.1.43242.1.216 | Scalareth | read-only | current | Display MAC address |
| 1.3.6.1.4.1.43242.1.217 | Scalarfor | read-write | current | Forceclose |
| 1.3.6.1.4.1.43242.1.218 | Scalaroth | read-write | current | Disable the other CPU |
| 1.3.6.1.4.1.43242.1.219 | ScalarvolPS1 | read-only | current | Power supply1 voltages |
| 1.3.6.1.4.1.43242.1.220 | ScalarvolPS2 | read-only | current | Power supply2 voltages |
| 1.3.6.1.4.1.43242.1.221 | Scalarfan | read-only | current | FAN speed |
| 1.3.6.1.4.1.43242.1.222 | Scalarpoa | read-write | current | Add port if there is space |
| 1.3.6.1.4.1.43242.1.223 | Scalarpod | read-write | current | Delet port if there are two for more ports in the port structure |
| 1.3.6.1.4.1.43242.1.224 | Scalarpol | read-only | current | Give a list of all ports in the port structure |
| 1.3.6.1.4.1.43242.1.225 | Scalarufw | read-write | current | Update firmware status returned |
| 1.3.6.1.4.1.43242.1.226 | Scalarexc | read-write | current | Exclude a particular signal path for Tristage algorithm |
| 1.3.6.1.4.1.43242.1.227 | Scalarinc | read-write | current | Undo a signal path exclusion for Tristage algorithm |
| 1.3.6.1.4.1.43242.1.228 | Scalarxcl | read-write | current | Clears all signal path exclusions for Tristage algorithm |
| 1.3.6.1.4.1.43242.1.229 | Scalarlci | read-write | current | LXI LAN Configuration initialize |
| 1.3.6.1.4.1.43242.1.230 | ScalartemPS1 | read-only | current | Display Power suppley1 temperature |
| 1.3.6.1.4.1.43242.1.231 | ScalartemPS2 | read-only | current | Display Power Supply2 temperature |
| 1.3.6.1.4.1.43242.1.232 | TabletrapHostIP | not-accessible | current | This table contions the destination IP addresses of TRAPs sent to the SNMP manager |
| 1.3.6.1.4.1.43242.1.232.1 | RowtrapHostIPentry | not-accessible | current | |
| 1.3.6.1.4.1.43242.1.232.1.1 | ColumntrapHostAddress | read-write | current | TRAP host IP address.to update use Forceclose/Reset |
| 1.3.6.1.4.1.43242.1.233 | Scalartime | read-write | current | Current time |
| 1.3.6.1.4.1.43242.1.234 | Scalardate | read-write | current | Current date |