MIB Viewer

VDSL-LINE-MIB

189 objects
The MIB module defining objects for the management of a pair of VDSL transceivers at each end of the VDSL line. Each such line has an entry in an ifTable which may include multiple transceiver lines. An agent may reside at either end of the VDSL line. However, the MIB is designed to require no management communication between them beyond that inherent in the low-level VDSL line protocol. The agent may monitor and control this protocol for its needs. VDSL lines may support optional Fast or Interleaved channels. If these are supported, additional entries corresponding to the supported channels must be created in the ifTable. Thus a VDSL line that supports both channels will have three entries in the ifTable, one for each physical, fast, and interleaved, whose ifType values are equal to vdsl(97), fast(125), and interleaved(124), respectively. The ifStackTable is used to represent the relationship between the entries. Naming Conventions: Vtuc Vtur Vtu Curr Prev Atn ES SES UAS LCS Lof Lol Los Lpr xxxs (e.g., xxx = Lof, Los, Lpr, Lol) Max Mgn Min Psd Snr Tx Blks Copyright (C) The Internet Society (2003). This version of this MIB module is part of RFC XXXX: see the RFC itself for full legal notices.
Imported Objects
HC-PerfHist-TC-MIBHCPerfCurrentCount HCPerfIntervalCount HCPerfIntervalThreshold HCPerfInvalidIntervals HCPerfTimeElapsed HCPerfValidIntervals
HCNUM-TCZeroBasedCounter64
IF-MIBifIndex
SNMP-FRAMEWORK-MIBSnmpAdminString
SNMPv2-CONFMODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP
SNMPv2-SMIGauge32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE transmission Unsigned32
SNMPv2-TCRowStatus TEXTUAL-CONVENTION TruthValue
OIDNameAccessStatusDescription
1.3.6.1.2.1.10.97IdentityvdslMIBThe MIB module defining objects for the management of a pair of VDSL transceivers at each end of the VDSL line. Each such line has an entry in an ifTable which…
1.3.6.1.2.1.10.97.1NodevdslLineMib
1.3.6.1.2.1.10.97.1.0NodevdslNotifications
1.3.6.1.2.1.10.97.1.0.1NotificationvdslPerfLofsThreshNotificationcurrentLoss of Framing 15-minute interval threshold (vdslThresh15MinLofs) reached.
1.3.6.1.2.1.10.97.1.0.2NotificationvdslPerfLossThreshNotificationcurrentLoss of Signal 15-minute interval threshold (vdslThresh15MinLoss) reached.
1.3.6.1.2.1.10.97.1.0.3NotificationvdslPerfLprsThreshNotificationcurrentLoss of Power 15-minute interval threshold (vdslThresh15MinLprs) reached.
1.3.6.1.2.1.10.97.1.0.4NotificationvdslPerfLolsThreshNotificationcurrentLoss of Link 15-minute interval threshold (vdslThresh15MinLols) reached.
1.3.6.1.2.1.10.97.1.0.5NotificationvdslPerfESsThreshNotificationcurrentErrored Seconds 15-minute interval threshold (vdslThresh15MinESs) reached.
1.3.6.1.2.1.10.97.1.0.6NotificationvdslPerfSESsThreshNotificationcurrentSeverely Errored Seconds 15-minute interval threshold (vdslThresh15MinSESs) reached.
1.3.6.1.2.1.10.97.1.0.7NotificationvdslPerfUASsThreshNotificationcurrentUnavailable Seconds 15-minute interval threshold (vdslThresh15MinUASs) reached.
1.3.6.1.2.1.10.97.1.0.8NotificationvdslDownMaxSnrMgnNotificationcurrentThe downstream Signal to Noise Margin exceeded vdslLineConfDownMaxSnrMgn. The object vdslPhysCurrSnrMgn will contain the Signal to Noise margin as measured by …
1.3.6.1.2.1.10.97.1.0.9NotificationvdslDownMinSnrMgnNotificationcurrentThe downstream Signal to Noise Margin fell below vdslLineConfDownMinSnrMgn. The object vdslPhysCurrSnrMgn will contain the Signal to Noise margin as measured b…
1.3.6.1.2.1.10.97.1.0.10NotificationvdslUpMaxSnrMgnNotificationcurrentThe upstream Signal to Noise Margin exceeded vdslLineConfUpMaxSnrMgn. The object vdslPhysCurrSnrMgn will contain the Signal to Noise margin as measured by the …
1.3.6.1.2.1.10.97.1.0.11NotificationvdslUpMinSnrMgnNotificationcurrentThe upstream Signal to Noise Margin fell below vdslLineConfUpMinSnrMgn. The object vdslPhysCurrSnrMgn will contain the Signal to Noise margin as measured by th…
1.3.6.1.2.1.10.97.1.0.12NotificationvdslInitFailureNotificationcurrentVtu initialization failed. See vdslPhysCurrStatus for potential reasons.
1.3.6.1.2.1.10.97.1.1NodevdslMibObjects
1.3.6.1.2.1.10.97.1.1.1TablevdslLineTablenot-accessiblecurrentThis table includes common attributes describing both ends of the line. It is required for all VDSL physical interfaces. VDSL physical interfaces are those ifE…
1.3.6.1.2.1.10.97.1.1.1.1RowvdslLineEntrynot-accessiblecurrentAn entry in the vdslLineTable.
1.3.6.1.2.1.10.97.1.1.1.1.1ColumnvdslLineCodingread-onlycurrentSpecifies the VDSL coding type used on this line.
1.3.6.1.2.1.10.97.1.1.1.1.2ColumnvdslLineTyperead-onlycurrentDefines the type of VDSL physical line entity that exists, by defining whether and how the line is channelized. If the line is channelized, the value will be o…
1.3.6.1.2.1.10.97.1.1.1.1.3ColumnvdslLineConfProfileread-writecurrentThe value of this object identifies the row in the VDSL Line Configuration Profile Table, vdslLineConfProfileTable, which applies for this VDSL line, and chann…
1.3.6.1.2.1.10.97.1.1.1.1.4ColumnvdslLineAlarmConfProfileread-writecurrentThe value of this object identifies the row in the VDSL Line Alarm Configuration Profile Table, vdslLineAlarmConfProfileTable, which applies to this VDSL line,…
1.3.6.1.2.1.10.97.1.1.2TablevdslPhysTablenot-accessiblecurrentThis table provides one row for each Vtu. Each row contains the Physical Layer Parameters table for that Vtu. VDSL physical interfaces are those ifEntries wher…
1.3.6.1.2.1.10.97.1.1.2.1RowvdslPhysEntrynot-accessiblecurrentAn entry in the vdslPhysTable.
1.3.6.1.2.1.10.97.1.1.2.1.1ColumnvdslPhysSidenot-accessiblecurrentIdentifies whether the transceiver is the Vtuc or Vtur.
1.3.6.1.2.1.10.97.1.1.2.1.2ColumnvdslPhysInvSerialNumberread-onlycurrentThe vendor specific string that identifies the vendor equipment.
1.3.6.1.2.1.10.97.1.1.2.1.3ColumnvdslPhysInvVendorIDread-onlycurrentThe vendor ID code is a copy of the binary vendor identification field expressed as readable characters in hexadecimal notation.
1.3.6.1.2.1.10.97.1.1.2.1.4ColumnvdslPhysInvVersionNumberread-onlycurrentThe vendor specific version number sent by this Vtu as part of the initialization messages. It is a copy of the binary version number field expressed as readab…
1.3.6.1.2.1.10.97.1.1.2.1.5ColumnvdslPhysCurrSnrMgnread-onlycurrentNoise Margin as seen by this Vtu with respect to its received signal in 0.25dB. The effective range is -31.75 to +31.75 dB.
1.3.6.1.2.1.10.97.1.1.2.1.6ColumnvdslPhysCurrAtnread-onlycurrentMeasured difference in the total power transmitted by the peer Vtu and the total power received by this Vtu. The effective range is 0 to +63.75 dB.
1.3.6.1.2.1.10.97.1.1.2.1.7ColumnvdslPhysCurrStatusread-onlycurrentIndicates current state of the Vtu line. This is a bit-map of possible conditions. The various bit positions are: 0 noDefect There are no defects on the line. …
1.3.6.1.2.1.10.97.1.1.2.1.8ColumnvdslPhysCurrOutputPwrread-onlycurrentMeasured total output power transmitted by this VTU. This is the measurement that was reported during the last activation sequence.
1.3.6.1.2.1.10.97.1.1.2.1.9ColumnvdslPhysCurrAttainableRateread-onlycurrentIndicates the maximum currently attainable data rate in steps of 1000 bits/second by the Vtu. This value will be equal to or greater than vdslPhysCurrLineRate.…
1.3.6.1.2.1.10.97.1.1.2.1.10ColumnvdslPhysCurrLineRateread-onlycurrentIndicates the current data rate in steps of 1000 bits/second by the Vtu. This value will be less than or equal to vdslPhysCurrAttainableRate. Note: 1 kbps = 10…
1.3.6.1.2.1.10.97.1.1.3TablevdslChanTablenot-accessiblecurrentThis table provides one row for each Vtu channel. VDSL channel interfaces are those ifEntries where ifType is equal to interleave(124) or fast(125).
1.3.6.1.2.1.10.97.1.1.3.1RowvdslChanEntrynot-accessiblecurrentAn entry in the vdslChanTable.
1.3.6.1.2.1.10.97.1.1.3.1.1ColumnvdslChanInterleaveDelayread-onlycurrentInterleave Delay for this channel. Interleave delay applies only to the interleave (slow) channel and defines the mapping (relative spacing) between subsequent…
1.3.6.1.2.1.10.97.1.1.3.1.2ColumnvdslChanCrcBlockLengthread-onlycurrentIndicates the length of the channel data-block on which the CRC operates.
1.3.6.1.2.1.10.97.1.1.3.1.3ColumnvdslChanCurrTxRateread-onlycurrentActual transmit data rate on this channel. Note: 1 kbps = 1000 bps.
1.3.6.1.2.1.10.97.1.1.3.1.4ColumnvdslChanCurrTxSlowBurstProtectread-onlycurrentActual level of impulse noise (burst) protection for an interleaved (slow) channel. This parameter is not applicable to fast channels. For fast channels, a val…
1.3.6.1.2.1.10.97.1.1.3.1.5ColumnvdslChanCurrTxFastFecread-onlycurrentActual Forward Error Correction (FEC) redundancy related overhead for a fast channel. This parameter is not applicable to an interleaved (slow) channel. For in…
1.3.6.1.2.1.10.97.1.1.4TablevdslPerfDataTablenot-accessiblecurrentThis table provides one row for each VDSL physical interface. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97).
1.3.6.1.2.1.10.97.1.1.4.1RowvdslPerfDataEntrynot-accessiblecurrentAn entry in the vdslPerfDataTable.
1.3.6.1.2.1.10.97.1.1.4.1.1ColumnvdslPerfDataValidIntervalsread-onlycurrentValid Intervals per definition found in HC-PerfHist-TC-MIB.
1.3.6.1.2.1.10.97.1.1.4.1.2ColumnvdslPerfDataInvalidIntervalsread-onlycurrentInvalid Intervals per definition found in HC-PerfHist-TC-MIB.
1.3.6.1.2.1.10.97.1.1.4.1.3ColumnvdslPerfDataLofsread-onlycurrentCount of seconds since the unit was last reset that there was Loss of Framing.
1.3.6.1.2.1.10.97.1.1.4.1.4ColumnvdslPerfDataLossread-onlycurrentCount of seconds since the unit was last reset that there was Loss of Signal.
1.3.6.1.2.1.10.97.1.1.4.1.5ColumnvdslPerfDataLprsread-onlycurrentCount of seconds since the unit was last reset that there was Loss of Power.
1.3.6.1.2.1.10.97.1.1.4.1.6ColumnvdslPerfDataLolsread-onlycurrentCount of seconds since the unit was last reset that there was Loss of Link.
1.3.6.1.2.1.10.97.1.1.4.1.7ColumnvdslPerfDataESsread-onlycurrentCount of Errored Seconds since the unit was last reset. An Errored Second is a one-second interval containing one or more CRC anomalies, or one or more LOS or …
1.3.6.1.2.1.10.97.1.1.4.1.8ColumnvdslPerfDataSESsread-onlycurrentCount of Severely Errored Seconds since the unit was last reset.
1.3.6.1.2.1.10.97.1.1.4.1.9ColumnvdslPerfDataUASsread-onlycurrentCount of Unavailable Seconds since the unit was last reset.
1.3.6.1.2.1.10.97.1.1.4.1.10ColumnvdslPerfDataInitsread-onlycurrentCount of the line initialization attempts since the unit was last reset. This count includes both successful and failed attempts.
1.3.6.1.2.1.10.97.1.1.4.1.11ColumnvdslPerfDataCurr15MinTimeElapsedread-onlycurrentTotal elapsed seconds in this interval.
1.3.6.1.2.1.10.97.1.1.4.1.12ColumnvdslPerfDataCurr15MinLofsread-onlycurrentCount of seconds during this interval that there was Loss of Framing.
1.3.6.1.2.1.10.97.1.1.4.1.13ColumnvdslPerfDataCurr15MinLossread-onlycurrentCount of seconds during this interval that there was Loss of Signal.
1.3.6.1.2.1.10.97.1.1.4.1.14ColumnvdslPerfDataCurr15MinLprsread-onlycurrentCount of seconds during this interval that there was Loss of Power.
1.3.6.1.2.1.10.97.1.1.4.1.15ColumnvdslPerfDataCurr15MinLolsread-onlycurrentCount of seconds during this interval that there was Loss of Link.
1.3.6.1.2.1.10.97.1.1.4.1.16ColumnvdslPerfDataCurr15MinESsread-onlycurrentCount of Errored Seconds during this interval. An Errored Second is a one-second interval containing one or more CRC anomalies, or one or more LOS or LOF defec…
1.3.6.1.2.1.10.97.1.1.4.1.17ColumnvdslPerfDataCurr15MinSESsread-onlycurrentCount of Severely Errored Seconds during this interval.
1.3.6.1.2.1.10.97.1.1.4.1.18ColumnvdslPerfDataCurr15MinUASsread-onlycurrentCount of Unavailable Seconds during this interval.
1.3.6.1.2.1.10.97.1.1.4.1.19ColumnvdslPerfDataCurr15MinInitsread-onlycurrentCount of the line initialization attempts during this interval. This count includes both successful and failed attempts.
1.3.6.1.2.1.10.97.1.1.4.1.20ColumnvdslPerfData1DayValidIntervalsread-onlycurrentValid Intervals per definition found in HC-PerfHist-TC-MIB.
1.3.6.1.2.1.10.97.1.1.4.1.21ColumnvdslPerfData1DayInvalidIntervalsread-onlycurrentInvalid Intervals per definition found in HC-PerfHist-TC-MIB.
1.3.6.1.2.1.10.97.1.1.4.1.22ColumnvdslPerfDataCurr1DayTimeElapsedread-onlycurrentNumber of seconds that have elapsed since the beginning of the current 1-day interval.
1.3.6.1.2.1.10.97.1.1.4.1.23ColumnvdslPerfDataCurr1DayLofsread-onlycurrentCount of Loss of Framing (LOF) Seconds since the beginning of the current 1-day interval.
1.3.6.1.2.1.10.97.1.1.4.1.24ColumnvdslPerfDataCurr1DayLossread-onlycurrentCount of Loss of Signal (LOS) Seconds since the beginning of the current 1-day interval.
1.3.6.1.2.1.10.97.1.1.4.1.25ColumnvdslPerfDataCurr1DayLprsread-onlycurrentCount of Loss of Power (LPR) Seconds since the beginning of the current 1-day interval.
1.3.6.1.2.1.10.97.1.1.4.1.26ColumnvdslPerfDataCurr1DayLolsread-onlycurrentCount of Loss of Link (LOL) Seconds since the beginning of the current 1-day interval.
1.3.6.1.2.1.10.97.1.1.4.1.27ColumnvdslPerfDataCurr1DayESsread-onlycurrentCount of Errored Seconds (ES) since the beginning of the current 1-day interval.
1.3.6.1.2.1.10.97.1.1.4.1.28ColumnvdslPerfDataCurr1DaySESsread-onlycurrentCount of Severely Errored Seconds (SES) since the beginning of the current 1-day interval.
1.3.6.1.2.1.10.97.1.1.4.1.29ColumnvdslPerfDataCurr1DayUASsread-onlycurrentCount of Unavailable Seconds (UAS) since the beginning of the current 1-day interval.
1.3.6.1.2.1.10.97.1.1.4.1.30ColumnvdslPerfDataCurr1DayInitsread-onlycurrentCount of the line initialization attempts since the beginning of the current 1-day interval. This count includes both successful and failed attempts.
1.3.6.1.2.1.10.97.1.1.5TablevdslPerfIntervalTablenot-accessiblecurrentThis table provides one row for each Vtu performance data collection interval. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97).
1.3.6.1.2.1.10.97.1.1.5.1RowvdslPerfIntervalEntrynot-accessiblecurrentAn entry in the vdslPerfIntervalTable.
1.3.6.1.2.1.10.97.1.1.5.1.1ColumnvdslPerfIntervalNumbernot-accessiblecurrentPerformance Data Interval number 1 is the most recent previous interval; interval 96 is 24 hours ago. Intervals 2 to 96 are optional.
1.3.6.1.2.1.10.97.1.1.5.1.2ColumnvdslPerfIntervalLofsread-onlycurrentCount of seconds in the interval when there was Loss of Framing.
1.3.6.1.2.1.10.97.1.1.5.1.3ColumnvdslPerfIntervalLossread-onlycurrentCount of seconds in the interval when there was Loss of Signal.
1.3.6.1.2.1.10.97.1.1.5.1.4ColumnvdslPerfIntervalLprsread-onlycurrentCount of seconds in the interval when there was Loss of Power.
1.3.6.1.2.1.10.97.1.1.5.1.5ColumnvdslPerfIntervalLolsread-onlycurrentCount of seconds in the interval when there was Loss of Link.
1.3.6.1.2.1.10.97.1.1.5.1.6ColumnvdslPerfIntervalESsread-onlycurrentCount of Errored Seconds (ES) in the interval. An Errored Second is a one-second interval containing one or more CRC anomalies, one or more LOS or LOF defects.
1.3.6.1.2.1.10.97.1.1.5.1.7ColumnvdslPerfIntervalSESsread-onlycurrentCount of Severely Errored Seconds in the interval.
1.3.6.1.2.1.10.97.1.1.5.1.8ColumnvdslPerfIntervalUASsread-onlycurrentCount of Unavailable Seconds in the interval.
1.3.6.1.2.1.10.97.1.1.5.1.9ColumnvdslPerfIntervalInitsread-onlycurrentCount of the line initialization attempts during this interval. This count includes both successful and failed attempts.
1.3.6.1.2.1.10.97.1.1.6TablevdslPerf1DayIntervalTablenot-accessiblecurrentThis table provides one row for each VDSL performance data collection interval. This table contains live data from equipment. As such, it is NOT persistent.
1.3.6.1.2.1.10.97.1.1.6.1RowvdslPerf1DayIntervalEntrynot-accessiblecurrentAn entry in the vdslPerf1DayIntervalTable.
1.3.6.1.2.1.10.97.1.1.6.1.1ColumnvdslPerf1DayIntervalNumbernot-accessiblecurrentHistory Data Interval number. Interval 1 is the most recent previous day; interval 30 is 30 days ago. Intervals 2 to 30 are optional.
1.3.6.1.2.1.10.97.1.1.6.1.2ColumnvdslPerf1DayIntervalMoniSecsread-onlycurrentThe amount of time in the 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval dur…
1.3.6.1.2.1.10.97.1.1.6.1.3ColumnvdslPerf1DayIntervalLofsread-onlycurrentCount of Loss of Frame (LOF) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
1.3.6.1.2.1.10.97.1.1.6.1.4ColumnvdslPerf1DayIntervalLossread-onlycurrentCount of Loss of Signal (LOS) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
1.3.6.1.2.1.10.97.1.1.6.1.5ColumnvdslPerf1DayIntervalLprsread-onlycurrentCount of Loss of Power (LPR) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
1.3.6.1.2.1.10.97.1.1.6.1.6ColumnvdslPerf1DayIntervalLolsread-onlycurrentCount of Loss of Link (LOL) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
1.3.6.1.2.1.10.97.1.1.6.1.7ColumnvdslPerf1DayIntervalESsread-onlycurrentCount of Errored Seconds (ES) during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
1.3.6.1.2.1.10.97.1.1.6.1.8ColumnvdslPerf1DayIntervalSESsread-onlycurrentCount of Severely Errored Seconds (SES) during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
1.3.6.1.2.1.10.97.1.1.6.1.9ColumnvdslPerf1DayIntervalUASsread-onlycurrentCount of Unavailable Seconds (UAS) during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
1.3.6.1.2.1.10.97.1.1.6.1.10ColumnvdslPerf1DayIntervalInitsread-onlycurrentCount of the line initialization attempts during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs. This count includes both successful and failed…
1.3.6.1.2.1.10.97.1.1.7TablevdslChanPerfDataTablenot-accessiblecurrentThis table provides one row for each Vtu channel. VDSL channel interfaces are those ifEntries where ifType is equal to interleave(124) or fast(125).
1.3.6.1.2.1.10.97.1.1.7.1RowvdslChanPerfDataEntrynot-accessiblecurrentAn entry in the vdslChanPerfDataTable.
1.3.6.1.2.1.10.97.1.1.7.1.1ColumnvdslChanValidIntervalsread-onlycurrentValid Intervals per definition found in HC-PerfHist-TC-MIB.
1.3.6.1.2.1.10.97.1.1.7.1.2ColumnvdslChanInvalidIntervalsread-onlycurrentInvalid Intervals per definition found in HC-PerfHist-TC-MIB.
1.3.6.1.2.1.10.97.1.1.7.1.3ColumnvdslChanFixedOctetsread-onlycurrentCount of corrected octets since the unit was last reset.
1.3.6.1.2.1.10.97.1.1.7.1.4ColumnvdslChanBadBlksread-onlycurrentCount of uncorrectable blocks since the unit was last reset.
1.3.6.1.2.1.10.97.1.1.7.1.5ColumnvdslChanCurr15MinTimeElapsedread-onlycurrentTotal elapsed seconds in this interval.
1.3.6.1.2.1.10.97.1.1.7.1.6ColumnvdslChanCurr15MinFixedOctetsread-onlycurrentCount of corrected octets in this interval.
1.3.6.1.2.1.10.97.1.1.7.1.7ColumnvdslChanCurr15MinBadBlksread-onlycurrentCount of uncorrectable blocks in this interval.
1.3.6.1.2.1.10.97.1.1.7.1.8ColumnvdslChan1DayValidIntervalsread-onlycurrentValid Intervals per definition found in HC-PerfHist-TC-MIB.
1.3.6.1.2.1.10.97.1.1.7.1.9ColumnvdslChan1DayInvalidIntervalsread-onlycurrentInvalid Intervals per definition found in HC-PerfHist-TC-MIB.
1.3.6.1.2.1.10.97.1.1.7.1.10ColumnvdslChanCurr1DayTimeElapsedread-onlycurrentNumber of seconds that have elapsed since the beginning of the current 1-day interval.
1.3.6.1.2.1.10.97.1.1.7.1.11ColumnvdslChanCurr1DayFixedOctetsread-onlycurrentCount of corrected octets since the beginning of the current 1-day interval.
1.3.6.1.2.1.10.97.1.1.7.1.12ColumnvdslChanCurr1DayBadBlksread-onlycurrentCount of uncorrectable blocks since the beginning of the current 1-day interval.
1.3.6.1.2.1.10.97.1.1.8TablevdslChanIntervalTablenot-accessiblecurrentThis table provides one row for each Vtu channel data collection interval. VDSL channel interfaces are those ifEntries where ifType is equal to interleave(124)…
1.3.6.1.2.1.10.97.1.1.8.1RowvdslChanIntervalEntrynot-accessiblecurrentAn entry in the vdslChanIntervalTable.
1.3.6.1.2.1.10.97.1.1.8.1.1ColumnvdslChanIntervalNumbernot-accessiblecurrentPerformance Data Interval number 1 is the most recent previous interval; interval 96 is 24 hours ago. Intervals 2 to 96 are optional.
1.3.6.1.2.1.10.97.1.1.8.1.2ColumnvdslChanIntervalFixedOctetsread-onlycurrentCount of corrected octets in this interval.
1.3.6.1.2.1.10.97.1.1.8.1.3ColumnvdslChanIntervalBadBlksread-onlycurrentCount of uncorrectable blocks in this interval.
1.3.6.1.2.1.10.97.1.1.9TablevdslChan1DayIntervalTablenot-accessiblecurrentThis table provides one row for each VDSL performance data collection interval. This table contains live data from equipment. As such, it is NOT persistent.
1.3.6.1.2.1.10.97.1.1.9.1RowvdslChan1DayIntervalEntrynot-accessiblecurrentAn entry in the vdslChan1DayIntervalTable.
1.3.6.1.2.1.10.97.1.1.9.1.1ColumnvdslChan1DayIntervalNumbernot-accessiblecurrentHistory Data Interval number. Interval 1 is the most recent previous day; interval 30 is 30 days ago. Intervals 2 to 30 are optional.
1.3.6.1.2.1.10.97.1.1.9.1.2ColumnvdslChan1DayIntervalMoniSecsread-onlycurrentThe amount of time in the 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval dur…
1.3.6.1.2.1.10.97.1.1.9.1.3ColumnvdslChan1DayIntervalFixedOctetsread-onlycurrentCount of corrected octets in this interval.
1.3.6.1.2.1.10.97.1.1.9.1.4ColumnvdslChan1DayIntervalBadBlksread-onlycurrentCount of uncorrectable blocks in this interval.
1.3.6.1.2.1.10.97.1.1.11TablevdslLineConfProfileTablenot-accessiblecurrentThis table contains information on the VDSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure …
1.3.6.1.2.1.10.97.1.1.11.1RowvdslLineConfProfileEntrynot-accessiblecurrentEach entry consists of a list of parameters that represents the configuration of a VDSL line. A default profile with an index of 'DEFVAL', will always exist an…
1.3.6.1.2.1.10.97.1.1.11.1.1ColumnvdslLineConfProfileNamenot-accessiblecurrentThis object identifies a row in this table. A default profile with an index of 'DEFVAL', will always exist and its parameters will be set to vendor specific va…
1.3.6.1.2.1.10.97.1.1.11.1.2ColumnvdslLineConfDownRateModeread-createcurrentSpecifies the rate selection behavior for the line in the downstream direction. manual(1) forces the rate to the configured rate adaptAtInit(2) adapts the line…
1.3.6.1.2.1.10.97.1.1.11.1.3ColumnvdslLineConfUpRateModeread-createcurrentSpecifies the rate selection behavior for the line in the upstream direction. manual(1) forces the rate to the configured rate adaptAtInit(2) adapts the line b…
1.3.6.1.2.1.10.97.1.1.11.1.4ColumnvdslLineConfDownMaxPwrread-createcurrentSpecifies the maximum aggregate downstream power level in the range 0 to 14.5 dBm.
1.3.6.1.2.1.10.97.1.1.11.1.5ColumnvdslLineConfUpMaxPwrread-createcurrentSpecifies the maximum aggregate upstream power level in the range 0 to 14.5 dBm.
1.3.6.1.2.1.10.97.1.1.11.1.6ColumnvdslLineConfDownMaxSnrMgnread-createcurrentSpecifies the maximum downstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB.
1.3.6.1.2.1.10.97.1.1.11.1.7ColumnvdslLineConfDownMinSnrMgnread-createcurrentSpecifies the minimum downstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB.
1.3.6.1.2.1.10.97.1.1.11.1.8ColumnvdslLineConfDownTargetSnrMgnread-createcurrentSpecifies the target downstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB. This is the Noise Margin the transceivers must achieve w…
1.3.6.1.2.1.10.97.1.1.11.1.9ColumnvdslLineConfUpMaxSnrMgnread-createcurrentSpecifies the maximum upstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB.
1.3.6.1.2.1.10.97.1.1.11.1.10ColumnvdslLineConfUpMinSnrMgnread-createcurrentSpecifies the minimum upstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB.
1.3.6.1.2.1.10.97.1.1.11.1.11ColumnvdslLineConfUpTargetSnrMgnread-createcurrentSpecifies the target upstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB. This is the Noise Margin the transceivers must achieve wit…
1.3.6.1.2.1.10.97.1.1.11.1.12ColumnvdslLineConfDownFastMaxDataRateread-createcurrentSpecifies the maximum downstream fast channel data rate in steps of 1000 bits/second.
1.3.6.1.2.1.10.97.1.1.11.1.13ColumnvdslLineConfDownFastMinDataRateread-createcurrentSpecifies the minimum downstream fast channel data rate in steps of 1000 bits/second.
1.3.6.1.2.1.10.97.1.1.11.1.14ColumnvdslLineConfDownSlowMaxDataRateread-createcurrentSpecifies the maximum downstream slow channel data rate in steps of 1000 bits/second. The maximum aggregate downstream transmit speed of the line can be derive…
1.3.6.1.2.1.10.97.1.1.11.1.15ColumnvdslLineConfDownSlowMinDataRateread-createcurrentSpecifies the minimum downstream slow channel data rate in steps of 1000 bits/second. The minimum aggregate downstream transmit speed of the line can be derive…
1.3.6.1.2.1.10.97.1.1.11.1.16ColumnvdslLineConfUpFastMaxDataRateread-createcurrentSpecifies the maximum upstream fast channel data rate in steps of 1000 bits/second. The maximum aggregate upstream transmit speed of the line can be derived fr…
1.3.6.1.2.1.10.97.1.1.11.1.17ColumnvdslLineConfUpFastMinDataRateread-createcurrentSpecifies the minimum upstream fast channel data rate in steps of 1000 bits/second. The minimum aggregate upstream transmit speed of the line can be derived fr…
1.3.6.1.2.1.10.97.1.1.11.1.18ColumnvdslLineConfUpSlowMaxDataRateread-createcurrentSpecifies the maximum upstream slow channel data rate in steps of 1000 bits/second.
1.3.6.1.2.1.10.97.1.1.11.1.19ColumnvdslLineConfUpSlowMinDataRateread-createcurrentSpecifies the minimum upstream slow channel data rate in steps of 1000 bits/second.
1.3.6.1.2.1.10.97.1.1.11.1.20ColumnvdslLineConfDownRateRatioread-createcurrentFor dynamic rate adaptation at startup, the allocation of data rate in excess of the minimum data rate for each channel is controlled by the object. This objec…
1.3.6.1.2.1.10.97.1.1.11.1.21ColumnvdslLineConfUpRateRatioread-createcurrentFor dynamic rate adaptation at startup, the allocation of data rate in excess of the minimum data rate for each channel is controlled by the object. This objec…
1.3.6.1.2.1.10.97.1.1.11.1.22ColumnvdslLineConfDownMaxInterDelayread-createcurrentSpecifies the maximum interleave delay for the downstream slow channel.
1.3.6.1.2.1.10.97.1.1.11.1.23ColumnvdslLineConfUpMaxInterDelayread-createcurrentSpecifies the maximum interleave delay for the upstream slow channel.
1.3.6.1.2.1.10.97.1.1.11.1.24ColumnvdslLineConfDownPboControlread-createcurrentDownstream power backoff (PBO) control for this line. For transceivers which do not support downstream PBO control, this object MUST be fixed at disabled(1). I…
1.3.6.1.2.1.10.97.1.1.11.1.25ColumnvdslLineConfUpPboControlread-createcurrentUpstream power backoff (PBO) control for this line. For transceivers which do not support upstream PBO control, this object MUST be fixed at disabled(1). If au…
1.3.6.1.2.1.10.97.1.1.11.1.26ColumnvdslLineConfDownPboLevelread-createcurrentSpecifies the downstream backoff level to be used when vdslLineConfDownPboControl = manual(3).
1.3.6.1.2.1.10.97.1.1.11.1.27ColumnvdslLineConfUpPboLevelread-createcurrentSpecifies the upstream backoff level to be used when vdslLineConfUpPboControl = manual(3).
1.3.6.1.2.1.10.97.1.1.11.1.28ColumnvdslLineConfDeploymentScenarioread-createcurrentThe VDSL line deployment scenario. When using fttCab(1), the VTU-C is located in a street cabinet. When using fttEx(2), the VTU-C is located at the central off…
1.3.6.1.2.1.10.97.1.1.11.1.29ColumnvdslLineConfAdslPresenceread-createcurrentIndicates presence of ADSL service in the associated cable bundle/binder. none(1) indicates no ADSL service in the bundle adslOverPots(2) indicates ADSL servic…
1.3.6.1.2.1.10.97.1.1.11.1.30ColumnvdslLineConfApplicableStandardread-createcurrentThe VDSL standard to be used for the line. ansi(1) indicates ANSI standard etsi(2) indicates ETSI standard itu(3) indicates ITU standard other(4) indicates a s…
1.3.6.1.2.1.10.97.1.1.11.1.31ColumnvdslLineConfBandPlanread-createcurrentThe VDSL band plan to be used for the line. bandPlan997(1) is to be used for ITU-T G.993.1 Bandplan-B ETSI Bandplan ANSI Plan 997 bandPlan998(2) is to be used …
1.3.6.1.2.1.10.97.1.1.11.1.32ColumnvdslLineConfBandPlanFxread-createcurrentThe frequency limit between bands D2 and U2 when vdslLineConfBandPlan is set to bandPlanFx(3).
1.3.6.1.2.1.10.97.1.1.11.1.33ColumnvdslLineConfBandOptUsageread-createcurrentDefines the VDSL link use of the optional frequency range [25kHz - 138kHz] (Opt). unused(1) indicates Opt is unused upstream(2) indicates Opt usage is for upst…
1.3.6.1.2.1.10.97.1.1.11.1.34ColumnvdslLineConfUpPsdTemplateread-createcurrentThe upstream PSD template to be used for the line. Here, templateMask1(1) refers to a notched mask that limits the transmitted PSD within the internationally s…
1.3.6.1.2.1.10.97.1.1.11.1.35ColumnvdslLineConfDownPsdTemplateread-createcurrentThe downstream PSD template to be used for the line. Here, templateMask1(1) refers to a notched mask that limits the transmitted PSD within the internationally…
1.3.6.1.2.1.10.97.1.1.11.1.36ColumnvdslLineConfHamBandMaskread-createcurrentThe transmit power spectral density mask code, used to avoid interference with HAM (Handheld Amateur Radio) radio bands by introducing power control (notching)…
1.3.6.1.2.1.10.97.1.1.11.1.37ColumnvdslLineConfCustomNotch1Startread-createcurrentSpecifies the start frequency of custom HAM (Handheld Amateur Radio) notch 1. vdslLineConfCustomNotch1Start MUST be less than or equal to vdslLineConfCustomNot…
1.3.6.1.2.1.10.97.1.1.11.1.38ColumnvdslLineConfCustomNotch1Stopread-createcurrentSpecifies the stop frequency of custom HAM (Handheld Amateur Radio) notch 1. vdslLineConfCustomNotch1Stop MUST be greater than or equal to vdslLineConfCustomNo…
1.3.6.1.2.1.10.97.1.1.11.1.39ColumnvdslLineConfCustomNotch2Startread-createcurrentSpecifies the start frequency of custom HAM (Handheld Amateur Radio) notch 2. vdslLineConfCustomNotch2Start MUST be less than or equal to vdslLineConfCustomNot…
1.3.6.1.2.1.10.97.1.1.11.1.40ColumnvdslLineConfCustomNotch2Stopread-createcurrentSpecifies the stop frequency of custom HAM (Handheld Amateur Radio) notch 2. vdslLineConfCustomNotch2Stop MUST be greater than or equal to vdslLineConfCustomNo…
1.3.6.1.2.1.10.97.1.1.11.1.41ColumnvdslLineConfDownTargetSlowBurstread-createcurrentSpecifies the target level of impulse noise (burst) protection for an interleaved (slow) channel.
1.3.6.1.2.1.10.97.1.1.11.1.42ColumnvdslLineConfUpTargetSlowBurstread-createcurrentSpecifies the target level of impulse noise (burst) protection for an interleaved (slow) channel.
1.3.6.1.2.1.10.97.1.1.11.1.43ColumnvdslLineConfDownMaxFastFecread-createcurrentThis parameter provisions the maximum level of Forward Error Correction (FEC) redundancy related overhead to be maintained for a fast channel.
1.3.6.1.2.1.10.97.1.1.11.1.44ColumnvdslLineConfUpMaxFastFecread-createcurrentThis parameter provisions the maximum level of Forward Error Correction (FEC) redundancy related overhead to be maintained for a fast channel.
1.3.6.1.2.1.10.97.1.1.11.1.45ColumnvdslLineConfLineTyperead-createcurrentThis parameter provisions the VDSL physical entity at start-up by defining whether and how the line will be channelized, i.e. which channel type(s) are support…
1.3.6.1.2.1.10.97.1.1.11.1.46ColumnvdslLineConfProfRowStatusread-createcurrentThis object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to 'active'. When 'active…
1.3.6.1.2.1.10.97.1.1.20TablevdslLineAlarmConfProfileTablenot-accessiblecurrentThis table contains information on the VDSL line alarm configuration. One entry in this table reflects a profile defined by a manager which can be used to conf…
1.3.6.1.2.1.10.97.1.1.20.1RowvdslLineAlarmConfProfileEntrynot-accessiblecurrentEach entry consists of a list of parameters that represents the configuration of a VDSL line alarm profile. A default profile with an index of 'DEFVAL', will a…
1.3.6.1.2.1.10.97.1.1.20.1.1ColumnvdslLineAlarmConfProfileNamenot-accessiblecurrentThe name for this profile as specified by an adminstrator.
1.3.6.1.2.1.10.97.1.1.20.1.2ColumnvdslThresh15MinLofsread-createcurrentThis object configures the threshold for the number of loss of frame seconds (lofs) within any given 15-minute performance data collection interval. If the val…
1.3.6.1.2.1.10.97.1.1.20.1.3ColumnvdslThresh15MinLossread-createcurrentThis object configures the threshold for the number of loss of signal seconds (loss) within any given 15-minute performance data collection interval. If the va…
1.3.6.1.2.1.10.97.1.1.20.1.4ColumnvdslThresh15MinLprsread-createcurrentThis object configures the threshold for the number of loss of power seconds (lprs) within any given 15-minute performance data collection interval. If the val…
1.3.6.1.2.1.10.97.1.1.20.1.5ColumnvdslThresh15MinLolsread-createcurrentThis object configures the threshold for the number of loss of link seconds (lols) within any given 15-minute performance data collection interval. If the valu…
1.3.6.1.2.1.10.97.1.1.20.1.6ColumnvdslThresh15MinESsread-createcurrentThis object configures the threshold for the number of errored seconds (ESs) within any given 15-minute performance data collection interval. If the value of e…
1.3.6.1.2.1.10.97.1.1.20.1.7ColumnvdslThresh15MinSESsread-createcurrentThis object configures the threshold for the number of severely errored seconds (SESs) within any given 15-minute performance data collection interval. If the …
1.3.6.1.2.1.10.97.1.1.20.1.8ColumnvdslThresh15MinUASsread-createcurrentThis object configures the threshold for the number of unavailable seconds (UASs) within any given 15-minute performance data collection interval. If the value…
1.3.6.1.2.1.10.97.1.1.20.1.9ColumnvdslInitFailureNotifyEnableread-createcurrentThis object specifies if a vdslInitFailureNotification notification will be generated if an initialization failure occurs.
1.3.6.1.2.1.10.97.1.1.20.1.10ColumnvdslLineAlarmConfProfRowStatusread-createcurrentThis object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to 'active'. When 'active…
1.3.6.1.2.1.10.97.1.3NodevdslConformance
1.3.6.1.2.1.10.97.1.3.1NodevdslGroups
1.3.6.1.2.1.10.97.1.3.1.1GroupvdslGroupcurrentA collection of objects providing information about a VDSL Line.
1.3.6.1.2.1.10.97.1.3.1.2GroupvdslNotificationGroupcurrentThis group supports notifications of significant conditions associated with VDSL Lines.
1.3.6.1.2.1.10.97.1.3.2NodevdslCompliances
1.3.6.1.2.1.10.97.1.3.2.1CompliancevdslLineMibCompliancecurrentThe compliance statement for SNMP entities which manage VDSL interfaces.
Type Definitions
NameSyntaxStatusDescription
VdslLineCodingTypeINTEGER { other(1), mcm(2), scm(3) }current
VdslLineEntityINTEGER { vtuc(1), vtur(2) }current
MIB Viewer